Ameriphone XL-40 Manuel utilisateur

©AMERIPHONE products are manufactured by Walker, a Division of Plantronics, Inc.

12082 Western Avenue, Garden Grove, CA 92841

(800) 874-3005 VOICE • (800) 772-2889 TTY/TDD • (714) 897-4703 FAX

email: [email protected] website: www.ameriphone.com

®

and Walker are all trademarks or registered trademarks of Plantronics, Inc.

E

N

G

L

I

S

H

E

S

P

A

Ñ

O

L

F

R

A

N

Ç

A

I

S

Operating Instructions

∆

M46802

®

XL

XL-40 AMPLIFIED TELEPHONE

The Extra Loud & Clear

with lighted keypad!

IMPORTANT INSTRUCTIONS

Important Safety

Instructions

When using your telephone

equipment, basic safety precautions

should always be followed to

reduce the risk of fire, electric

shock and persons including the

following:

1.Read and understand all

instructions.

2.Follow all warnings and

instructions marked on the

telephone.

3.Do not use this telephone

near a bathtub, wash basin,

kitchen sink or laundry tub, in

a wet basement, near a

swimming pool or anywhere

else there is water.

4.Avoid using a telephone

(other than a cordless type)

during a storm. There may be

a remote risk of electrical

shock from lightning.

5.Do not use the telephone to

report a gas leak in the

vicinity of the leak.

6.Unplug this telephone from

the wall outlets before

cleaning. Do not use liquid

cleaners or aerosol cleaners

on the telephone. Use a damp

cloth for cleaning.

7.Place this telephone on a

stable surface. Serious damage

and/or injury may result if the

telephone falls.

8.Do not cover the slots and

openings on this telephone.

This telephone should never

be placed near or over a

radiator or heat register. This

telephone should not be

placed in a built-in installation

unless proper ventilation is

provided.

9.Operate this telephone using

the electrical voltage as

stated on the base unit or the

owner’s manual. If you are

not sure of the voltage in your

home, consult your dealer or

local power company.

10. Do not place anything on

the power cord. Install the

telephone where no one will

step or trip on the cord.

11. Do not overload wall outlets

or extension cords as this

can increase the risk of fire or

electrical shock.

12. Never push any objects

through the slots in the

telephone. They can touch

dangerous voltage points or

short out parts that could

result in a risk of fire or

electrical shock. Never spill

liquid of any kind on the

telephone.

13. To reduce the risk of electrical

shock, do not take this phone

E

N

G

L

I

S

H

Important Safety

Instructions

apart. Opening or removing

covers may expose you to

dangerous voltages or other

risks. Incorrect reassembly

can cause electric shock when

the appliance is subsequently

used.

14. Unplug this product from the

wall outlets and refer

servicing to the manufacturer

under the following conditions:

A. When the power supply

cord or plug is frayed or

damaged.

B. If liquid has been spilled

into the product.

C. If the telephone has been

exposed to rain or water.

D. If the telephone does not

operate normally by

following the operating

instructions. Adjust only

those controls that are

covered by the operating

instructions. Improper

adjustment may require

extensive work by a

qualified technician to

restore the telephone to

normal operation.

E. If the telephone has been

dropped or the case has

been damaged.

F. If the telephone exhibits a

distinct change in performance.

15. Never install telephone

wiring during a lightning

storm.

16. Never install telephone

jacks in wet locations

unless the jack is specifically

designed for wet locations.

17. Never touch uninsulated

telephone wires or terminals

unless the telephone line

has been disconnected at

the network interface.

18. Use caution when installing

or modifying telephone lines.

19. Use only the power cord

and batteries indicated in

this manual. Do not dispose

of batteries in a fire. They

may explode. Check with

local codes for possible

special disposal instructions.

ADDITIONAL SAFETY NOTES

FOR CANADIAN USERS

The following items are included

as part of the CS-03 Requirements.

The standard connecting

arrangement for the equipment is

CA11A. This product meets the

applicable Industry Canada

technical specifications.

NOTICE: The Canadian

Department of Communications

Important Safety

Instructions

label identifies certified equipment.

This certification means that the

equipment meets certain

telecommunications network

protective operational and safety

requirements. The Department

does not guarantee that the

equipment will operate to the

user’s satisfaction. Before installing

this equipment, users should

ensure that it is permissible to be

connected to the facilities of the

local telecommunications company.

The equipment must also be

installed using an acceptable

method of connection. In some

cases, the company’s inside

wiring associated with a single

line individual service may be

extended by means of a certified

connector assembly (telephone

extension cord). The customer

should be aware that compliance

with the above conditions may not

prevent degradation of service in

some situations. Repairs to certified

equipment should be made by an

authorized Canadian maintenance

facility designated by the supplier.

Any repairs or alterations made

by the user to this equipment, or

equipment malfunctions, may give

the telecommunications company

cause to request the user disconnect

the equipment.

Users should ensure for their own

protection that the electrical

ground connections of the power

utility, telephone lines and internal

metallic water pipe system, if

present, are connected together.

This precaution may be particularly

important in rural areas.

CAUTION: Users should not

attempt to make such connections

themselves, but should contact the

appropriate electric inspection

authority, or electrician, as

appropriate. The Ringer Equivalent

Number is an indication of the

maximum number of terminals

allowed to be connected to a

telephone interface. The

termination on an interface may

consist of any combination of

devices subject only to the

requirement that the sum of the

Ringer Equivalent Number of all

the devices not exceed five.

SAVE THESE INSTRUCTIONS

E

N

G

L

I

S

H

Contents

Introducing the XL-40

Warranty Service..............................................................................1

Sales Receipt ....................................................................................1

Help from Ameriphone ......................................................................1

Package Checklist ............................................................................2

Features ..........................................................................................3

Setting up Your XL-40

Installing the Backup Batteries ............................................................4

Setting the Dialing Mode ..................................................................5

Connecting for Desk or Wall Mount ..................................................5

Desktop Use ..............................................................................5

For Wall Mounting ......................................................................5

Using Your XL-40

Incoming Voice Volume......................................................................7

Incoming Voice Tone..........................................................................8

Ringer Volume and Tone ....................................................................8

Hold................................................................................................8

Last Number Redial ..........................................................................9

Flash................................................................................................9

Special Features

Unanswered Call/Voice Mail Message Light ......................................10

Programming the Memory Buttons......................................................11

Direct Audio Output ........................................................................12

Cochlear Implant Adapter Cord ........................................................12

Connecting to Speech Processor ........................................................12

Regulatory Compliance ....................................................................13

Warranty ........................................................................................19

Specifications ..................................................................................21

Troubleshooting Chart ......................................................................21

Index..............................................................................................22

Help from Ameriphone

For help with using your XL-40, call

our Customer Relations department

at 800-874-3005.

Please make sure your XL-40

package includes the items shown

in Figure 1.

1

Introducing the XL-40

Thank you for selecting the XL-40

Amplified Telephone from

Ameriphone. These Operating

Instructions and the associated

Quick Operating Guide provide

you with the information you

need to use your XL-40 effectively,

easily and safely. Read this

manual thoroughly before using

your telephone. Keep the manual

near the telephone for easy

reference.

Warranty Service

Your telephone is designed to

provide years of quality service.

But, should the phone malfunction

and the Trouble-shooting Chart

on page 12 not resolve the

problem, follow the Warranty

procedure on page 19.

Sales Receipt

Be sure to save your sales receipt

as proof of purchase date should

you need warranty service.

E

N

G

L

I

S

H

2

Package Checklist

1

A

B

C

G

H

I

P

R

S

T

U

V

W

X

Y

J

K

L

M

N

O

D

E

F

23

4

5

6

789

0

#

*

HOLD PROG

TONE

LO HI

FLASH REDIAL

VOL

AMPLIFY

M1

M2

M3

M4

M5

M6

M7

M8

M9

M11

M10

¤

OPERATING

INSTRUCTIONS

AND

QUICK GUIDE

XL-40

Handset

Base Unit

Telephone Line Cords

Handset

Coil Cord

Operating Guides

Figure 1 - Package Components

Mounting Bracket

AC Adapter

3

Features on the XL-40

RINGER volume switch

AUDIO OUTPUT jack

AC adapter and phone

line connection

TONE/PULSE switch

RING TONE switch

Phone number

directory

MEMORY button

REDIAL button

FLASH button

VOL volume slider

LOW BATTERY indicator

RING flasher

AMPLIFY button

AMPLIFY/MISSED CALLS/

VOICE MAIL/EXTENSION

IN USE indicator

PROG program button

RINGER

RING TONE DIAL

AUDIO

OUTPUT

Lo Med Hi

T P

Lo Hi

1

A

B

C

G

H

I

P

R

S

T

U

V

W

X

Y

J

K

L

M

N

O

D

E

F

23

4

5

6

789

0

#

*

HOLD PROG

TONE

LO

HI

FLASH

REDIAL

VOL

AMPLIFY

M1

M2

M5

M6

M7

M8

M9

M10

M11

M3

M4

¤

TONE

slider

HOLD

button

Figure 2 - Base Unit Controls

HOLD

indicator

Insert 4 AA

batteries

here

Press in

here with a

tip of a pen

to open

btt

4

Setting up Your XL-40

There are five initial steps involved

in setting up your XL-40 for the

first time.

1. Insert four AA alkaline

batteries for back-up in case

of AC power outage.

2. Decide if you want the

phone to sit on a desk or

hang on the wall.

3. Connect the telephone

components.

4. Program up to 12 telephone

numbers to call with the

press of a memory button.

5. Set up special features

Installing the Backup Batteries

If there is a power outage, the

XL-40 will operate for up to 48

hours with four AA alkaline

backup batteries (not included). If

the phone is not in use, the

batteries may last for several months.

To install new batteries:

1. Slide open the battery

compartment cover on the

bottom of the telephone

(Figure 3).

2. Install four fresh batteries. Be

sure to observe battery polarity

as imprinted on the base of

the compartment. The battery

indicator on the top panel

will light up if the batteries

are running low.

The phone operates as a regular

phone if there is no power or battery.

XL-40 Low Battery Indicator Light

If the batteries are weak or not

installed, the Low Battery indicator

will light up. Install fresh batteries

according to the directions above.

E

N

G

L

I

S

H

Figure 3 - Accessing the Batteries

HOLD PROG

TONE

LO HI

FLASH REDIAL

VOL

AMPLIFY

Figure 4 - Low Battery Indicator Light

Setting the Dialing Mode

Set the dial mode switch to T

(tone) if you have touch tone

service. Set the switch to P (pulse)

if you have rotary dialing.

Connecting for Desk or Wall Mount

For Desktop Use

1. Connect one end of the

telephone line cord to the

“Line” jack on the back of

the XL-40 and the other end

to the phone outlet on your

wall. Connect the handset

cord to the telephone as

shown in Figure 5.

2. Plug the AC adapter into an

electric outlet and into the

AC jack on the telephone as

shown in Figure 5.

5

Setting up Your XL-40

(continued)

3. Lift the handset and listen for

a dial tone.

The phone is ready to use.

For W

all Mounting

1. Slide the handset hook out of

the base as shown in Figure

6 and reverse its position so

that the hook points up and

will hold the handset when

you hang up.

2. Insert the tabs of the phone

base into the slots in the

lower position of the base as

shown in Figure 7. Push the

mounting bracket in and

down firmly until it snaps into

place.

M

1

M

2

M

5

M

6

M

7

M

8

M

9

M

10

M

11

M

3

M

4

Figure 5 - Connecting the Components

Line Cord

AC Adapter

Handset

(Curly)

Cord

Figure 6 - Reversing the Hook

E

N

G

L

I

S

H

6

Setting up Your XL-40

(continued)

3. Locate a desired wall phone

jack near an AC outlet and

hold phone upright.

4. Plug the short phone line

cord into the wall outlet as

shown in Figure 8.

MANUAL

AUTO

Figure 7 - Mounting Bracket

for Wall Mounting

5. Angle the phone downward

to feel for the LOWER

protruding nail head. Insert

the WALL JACK'S nail head

into the LOWER part of the

phone's mounting bracket.

6. Once the lower nail head

has been inserted, insert the

UPPER nail head into the

phone's bracket and slide

the phone down until it is

firmly in place on the wall.

7. Once firmly in place, attach

the short line cord to the

phone, the AC adapter to

the phone and attach the

phone's handset.

8. Plug the AC adapter into the

AC wall outlet. Lift the

handset and listen for a dial

tone. The phone is now

ready to use.

Figure 8 - Wall mounting installation

M

A

N

U

A

L

A

U

T

O

- Short phone

line cord

7

Using Your XL-40

Caution: Repeated incremental

exposure to amplification levels

greater than 18 dB may be

harmful

to individuals without

hearing disabilities

. Therefore, do

not remove the warning label

attached to the back of the

handset. If it is likely that a

visually impaired person will use

the

telephone, securely attach the

provided

warning printed in

Braille to the back of the handset

(See Diagram A).

Incoming Voice Volume

You can adjust the volume of

incoming

calls by simply sliding

the VOL control. This gives you up

to 18 dB more volume. If you

want more amplification, follow

the directions below.

1. Press the AMPLIFY button as

shown in Figure 9 to turn the

incoming voice amplifier on or

off. When AMPLIFY is on, the

AMPLIFY indicator comes on.

2. Adjust the ear piece volume

while on a call by moving the

VOL slide control in Figure 10.

With AMPLIFY on, incoming

volume will be up to 40dB

louder.

Diagram A.

0

#

HOLD PROG

TONE

LO HI

FLASH REDIAL

VOL

AMPLIFY

*

Figure 9 - AMPLIFY Button

and Indicator

0

#

HOLD PROG

TONE

LO HI

FLASH REDIAL

VOL

AMPLIFY

*

Figure 10 - Volume Slide Control

LOUD

V

OLUME

USE WITH

CAUTION

E

N

G

L

I

S

H

8

Using Your XL-40

(Continued)

Note: In standard use, the amplifier

turns off when you hang up the

telephone. This is a useful feature

if many people use the phone. If

you want the amplifier to always

remain on, slide the Volume Reset

Override switch on the bottom of

the phone to ON, as shown in

Figure 11.

Incoming Voice Tone

The XL-40 provides extra

amplification in the sound frequency

range you need to boost. To

identify the range that best suits

your needs, follow these steps:

1. When you hear a voice on the

line, press the AMPLIFY button

shown in Figure 9.

2. Adjust the TONE slide control in

Figure 12 to suit your hearing.

Figure 11 - Volume Reset Override

On/Off

MANUAL

AUTO

- OFF

- ON

Volume

Reset

Override

0

#

HOLD PROG

TONE

LO HI

FLASH REDIAL

VOL

AMPLIFY

*

Figure 12 - Tone Slide Control

RINGER

RING TONE DIAL

AUDIO

OUTPUT

Lo Med Hi

T P

Lo Hi

Figure 13 - Ringer Volume & Pitch

Ringer Volume and Tone

1. You can adjust the RINGER

VOLUME

as high as 95+

decibels. The settings available

are

LO, MED and HI as shown

in Figure 13.

2. The

RING TONE has two pitch

settings:

LO and HI.

Hold

To put the line on hold, press the

HOLD button and return the hand-

set to its cradle. You will notice the

HOLD indicator light comes on.

9

Using Your XL-40

(Continued)

Last Number Redial

To redial the last number called,

lift the handset and press REDIAL.

The phone will redial up to 31

digits.

0

#

HOLD PROG

TONE

LO HI

FLASH REDIAL

VOL

AMPLIFY

*

Figure 16 - Flash Button

0

#

HOLD PROG

TONE

LO HI

FLASH REDIAL

VOL

AMPLIFY

*

Figure 15 - Redial Button

Note: If you pick up an extension

phone on the same line when the

XL-40 is on HOLD, the XL-40 will

release the HOLD, and you can

continue your conversation on the

extension phone.

0

HOLD PROG

TONE

LO HI

FLASH REDIAL

VOL

AMPLIFY

Figure 14 - Hold Button and

Indicator

Flash

Press the FLASH button shown in

Figure 16 to access special

services available from your local

phone company such as Call

Waiting and 3-Way Calling.

E

N

G

L

I

S

H

10

Special Features

call is not answered by a person

or an answering machine after 1

ring, provided that you set the

switch underneath the phone to

Missed Calls. The light will

continue to flash until the handset

is lifted or AC power is disconnected.

Note: this feature does not require

any optional telephone company

services.

It is useful when you are away for

a short time while expecting a

call. If you don’t want any

notification, set the switch on OFF.

Unanswered Call/Voice Mail

Message Light

If you subscribe to voice mail

messaging with your telephone

company, this light flashes if you

have a message waiting.

Note: To turn the Voice Mail

feature on or off, adjust the switch

underneath the phone.

If you do not have voice mail

service, the same indicator

functions as a missed call

indicator. It flashes if an incoming

0

#

HOLD PROG

TONE

LO HI

FLASH REDIAL

VOL

AMPLIFY

*

Figure 17 - Voice Mail Indicator

VMAIL

MISSED CALL

OFF

Figure 18 - Voice Mail Switch

11

Special Features

(continued)

3. Press a memory button (Figure

19) to store this number on that

button.

4. Immediately hang up the

handset.

Note: Any number previously

stored at that memory button

will be overwritten.

5. To change a stored number,

repeat the programming

process starting with step 1.

1

C

G

H

I

P

R

S

T

U

V

O

P

E

W

X

Y

J

K

L

M

N

O

F

23

4

5

6

789

0

#

*

HOLD PROG FLASH REDIAL

Figure 21 - Telephone Keypad

2. Enter the phone number on the

keypad (Figure 21) just as you

would dial it normally.

Note: Press REDIAL if you want

to insert a brief pause between

two numbers.

To program a button, follow these

steps:

1. Lift the handset and press

PROG as shown in Figure 20.

1

A

B

D

E

23

M2

M3

M4

M5

M6

M8

M9

M11

M10

¤

Figure 19 - Memory Buttons

0

#

HOLD PROG

TONE

LO HI

FLASH REDIAL

VOL

AMPLIFY

*

Figure 20 - PROG Button

Programming the Memory Buttons

You can automatically dial twelve

programmed telephone numbers

using the memory buttons shown

in Figure 19. Each button can be

programmed (or reprogrammed

using the same procedure) for a

phone number up to 15 digits

long.

E

N

G

L

I

S

H

12

RINGER

RING TONE DIAL

AUDIO

OUTPUT

Lo Med Hi

T P

Lo Hi

Figure 22 - Audio Output

Socket

To use this port, plug in a

compatible auxiliary cable and

connect it to your assistive

listening device. Speak into the

handset when you use the Audio

Output connection.

Cochlear Implant Adapter Cord

A cochlear adapter cord is

available from Ameriphone that

can be used to directly connect the

XL-40 to a speech processor.

Connecting the speech processor:

Caution: Before plugging any cord

into your speech processor, you

must consult your implant

manufacturer.

•Plug the mono end of the plug

into the speech processor.

•Plug the stereo end of the plug

into the Audio Output socket on

the phone.

•Speak into the handset when

using the Cochlear Implant

Adapter Cord

WARNING! During thunderstorms,

avoid using telephones (except

cordless models). Electric shock

from lightning can occur.

Figure 23 - Connection of

Speech Processor

Special Features

(continued)

Note:

Please do not program 911

in any memory button.

Direct Audio Output

The AUDIO OUTPUT socket allows

you to connect the XL-40 to a

hearing aid, neck loop, cochlear

implant or other assistive listening

devices.

13

Regulatory Compliance

Part 68 of FCC Rules

Information

This equipment complies with Part

68 of the FCC rules and the

requirements adopted by the

ACTA. On the bottom of this

equipment is a label that contains,

among other information, a

product identifier in the format

US:AAAEQ##TXXXX. If requested,

this

number must be provided to the

telephone company.

A plug and jack used to connect

this equipment

to the premises

wiring and telephone network

must comply with the applicable

FCC Part 68 rules and requirements

adopted by the ACTA. A compliant

telephone cord and modular plug

,

RJ11 USOC, is provided with this

product. It is designed to be

connected to a compatible modular

jack that is also compliant. See

installation instructions for details.

The REN is used to determine the

number of devices that may be

connected to a telephone line.

Excessive RENs on a telephone

line may result in the devices not

ringing in response to an incoming

call. In most but not all areas, the

sum of RENs should not exceed

five (5.0). To be certain of the

number of devices that may be

connected to a line, as determined

by the total RENs, contact the

local telephone company. For

products approved after July 23,

2001, the REN for this product is

part of the product identifier that

has the format US:AAAEQ##TXXXX.

The digits represented by ## are

the REN without a decimal point

(e.g., 03 is a REN of 0.3). For

earlier products,

the REN is

separately shown on the label.

If this telephone equipment, the

XL-40 telephone, causes harm to

the telephone network, the

telephone company will notify you

in advance that temporary

discontinuance of service may be

required. But if advance notice

isn’t practical, the telephone

company will notify the customer

as soon as possible. Also, you will

be advised of your right to file a

complaint with the FCC if you

E

N

G

L

I

S

H

14

believe it is necessary.

The telephone company may

make changes in its facilities,

equipment, operations or procedures

that could affect the operation of

the equipment. If this happens the

telephone company will provide

advance notice in order for you to

make necessary modifications to

maintain uninterrupted service.

If trouble is experienced with this

telephone equipment, for repair or

warranty information, please contact

Walker / Ameriphone, 1-800-

874-3005. If the equipment is

causing harm to the telephone

network, the telephone company

may request that you disconnect

the equipment until the problem is

resolved.

DO NOT DISASSEMBLE THIS

EQUIPMENT.

This telephone equipment is not

intended to be repaired and it

contains no repairable parts.

Opening the equipment or any

attempt to perform repairs will

void the warranty. For service or

repairs, call 1-800-874-3005.

Connection to party line service is

subject to state tariffs. Contact the

state public utility commission,

public service commission or

corporation commission for

information.

If your home has specially wired

alarm equipment connected to the

telephone line, ensure the

installation of this telephone

equipment does not disable your

alarm equipment. If you have

questions about what will disable

alarm equipment, consult your

telephone company or a qualified

installer.

This telephone equipment is

hearing aid compatible.

We recommend the installation of

an AC surge arrester in the AC

outlet to which this equipment is

connected. The telephone

companies report that electrical

surges, typically lighting transients,

are very destructive to customer

terminal equipment connected to

AC power sources.

Regulatory Compliance

(continued)

La page charge ...

Ameriphone XL-40 Manuel utilisateur

Ce manuel convient également à

Ameriphone XL-40 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents