Simplicity 030735-00 Manuel utilisateur

Catégorie
Groupes électrogènes
Taper
Manuel utilisateur

Ce manuel convient également à

Not for
Reproduction
Manual No. 80023583 Revision A
Outdoor Inverter Generator
Operator’s Manual
Model Number _____________________________
Revision __________________________________
Serial Number ______________________________
Date Purchased ____________________________
Copyright © 2017. Briggs & Stratton Corporation
Milwaukee, WI, USA. All rights reserved.
800-743-4115
BRIGGSandSTRATTON.COM
Not for
Reproduction
EN2 BRIGGSandSTRATTON.COM
Equipment Description
Table of Contents
Equipment Description.........................2
Features and Controls .........................5
Operation....................................7
Maintenance ................................12
Storage ....................................15
Troubleshooting/Specifications .................16
Warranty ...................................18
Register Your Product
To ensure prompt and complete warranty coverage, register
your product online at www.onlineproductregistration.com.
Symbols and Meanings
Signal Meaning
DANGER
Indicates a hazard which, if not avoided, will
result in death or serious injury.
WARNING
Indicates a hazard which, if not avoided, could
result in death or serious injury.
CAUTION
Indicates a hazard which, if not avoided, could
result in minor or moderate injury.
NOTICE
Indicates information considered important, but
not hazard-related.
Symbol Name Explanation
Safety Alert
Symbol
Indicates a potential personal injury
hazard.
Operator’s
Manual
Failure to follow warnings, instructions
and operator’s manual could result in
death or serious injury.
Toxic
Fumes
Engine exhaust contains carbon
monoxide, a poisonous gas that
could kill you in minutes. You cannot
smell it or see it.
Fire
Fuel and its vapors are extremely
flammable which could cause burns or
fire resulting in death or serious injury.
Engine exhaust could cause fire
resulting in death or serious injury.
Electric
Shock
Generator could cause electrical
shock resulting in death or serious
injury.
Hot Surface
Muffler could cause burns or
resulting in serious injury.
WARNING! This product can expose you to
chemicals including gasoline engine exhaust, which is
known to the State of California to cause cancer, and
carbon monoxide, which is known to the State of California to
cause birth defects or other reproductive harm. For more
information go to www.P65Warnings.ca.gov.
Equipment Description
Read this manual carefully and become familiar
with your outdoor generator. Know its applications,
its limitations, and any hazards involved. Save
these original instructions for future reference.
The generator is an engine–driven, revolving field,
alternating and direct current (AC & DC) generator. It
was designed to supply electrical power for operating
compatible electrical lighting, appliances, tools and motor
loads. The generator’s revolving field is driven at about

switch off) by a single-cylinder engine.
The outdoor generator produces power that can be used for
outdoor items using extension cords or for first time temporary
home power restoration. Before your next home power outage,
install a listed transfer switch. A transfer switch is a separate device
installed by a licensed electrician that allows the portable generator
to be cord connected, using the locking receptacle, directly into
your home’s electrical system. Extension cords connected to the
portable generator’s control panel are not intended to be a long
term solution when connected to items inside your home.
Every effort has been made to ensure that the information in this
manual is both accurate and current. However, the manufacturer
reserves the right to change, alter or otherwise improve the
generator and this documentation at any time without prior notice.
NOTICE If you have questions about intended use, contact an
authorized service dealer. This equipment is designed to be used
with Briggs & Stratton authorized parts only.
This spark ignition system complies with the Canadian
standard ICES-002.

This feature is designed to greatly improve fuel economy.
When switch is ON (I), engine speed increases as
electrical loads are connected, and decreases as electrical
loads are removed.
With switch OFF (0), engine will run at full governed
speed.
NOTICE Always have the switch OFF (0) when starting or
stopping generator or when using DC USB ports.
Not for
Reproduction
EN3
System Ground
The generator has a system ground that connects the generator
frame components to the ground terminals on the AC output
receptacles. The system ground is connected to the AC neutral
wire (the neutral is bonded to the generator frame).
Special Requirements
There may be Federal or State regulations, local codes, or
ordinances that apply to the intended use of the generator.
Please consult a qualified electrician,
electrical inspector, or
the local agency having jurisdiction.
This generator is not intended to be used at a construction
site or similar activity as defined by NFPA 70-2014 (NEC)
section 590.6.
To Temporarily Restore Power Using
Extension Cords
1. Only use cords marked for outdoor use rated for your
loads.
To Temporarily provide power
using extension cords
Total
Amperage
Minimum Guage, Outdoor Rated
Up to 50 FT (15 M) Up to 100 FT (30 M)
Up to 13A
16
14
Up to 15A
14
12
Up to 20A
12
10
Up to 30A
10
8
2. Follow cord safety instructions.
3. Extension cords running directly into the home
increase your risk of carbon monoxide poisoning
through openings. Install carbon monoxide alarm(s).
4. Before your next home power outage, install a listed*
transfer switch.

Transfer Switch
Connections to your home’s electrical system must use a
listed transfer switch installed by a licensed electrician. The
connection must isolate the generator power from the utility
power and comply with all applicable laws and electrical
codes. Power your home with a 30 Amp transfer switch
system.
Equipment Description
120V
OUTLET

product complies to appropriate product safety test standards.
120/240V
Outlet
Transfer
Switch
Typical Indoor Items
Not for
Reproduction
EN4 BRIGGSandSTRATTON.COM
Equipment Description
Air Cleaner (under back cover) — Filters engine intake air.
Back Cover — Remove to gain access to the air filter.
Choke Control — Used when starting a cold engine.
Engine Identification (under side maintenance cover) —
Provides model, type and serial number of engine.
Engine Switch — Set switch to ON (I) before using recoil
starter. Set switch to OFF (0) to stop engine. Also turns fuel
valve on and off.
Fuel Cap — Add unleaded fuel here.
Grounding Fastener — Consult your local agency having
jurisdiction for grounding requirements in your area.
Handholds — Provided for convenient lifting.

generator.
Oil Drain Plug — Drain engine oil here.
Oil Fill/Dipstick (under side maintenance cover) — Check
and add engine oil here.
Recoil Starter — Used to start the engine manually.
Retractable Handle — Press button and pull handle out to
move generator. Press button to push handle back in.
Side Maintenance Cover — Remove to gain access to the
spark plug, spark arrester, and oil service.
Spark Arrester Muffler — Exhaust muffler lowers engine
noise and is equipped with a spark arrester screen.
Engine Identification
Oil Fill/Dipstick
Oil Drain Plug
Fuel Cap
Spark Arrester Muffler
Air Cleaner

Side Maintenance Cover
Back Cover
Handhold
Handhold
Grounding Fastener
Choke Control
Engine Switch
Recoil Starter
Retractable Handle
Handholds
Not for
Reproduction
EN5
Features and Controls
120 Volt AC, 20 Amp, GFCI Duplex Receptacles — Used
to supply 120 Volt AC, single phase, 60 Hz power for
electrical lighting, appliance, tool and motor loads.

supply 120 / 240 Volt AC, single phase, 60 Hz power for
electrical lighting, appliance, tool and motor loads.
Circuit Breakers (AC) — The 120 Volt AC, 20A GFCI
duplex receptacles are provided with “push to reset” 20
Amp circuit breakers to protect the generator against
electrical overload.

protection device. Oil must be at proper level for engine
to run. If the engine oil drops below a preset level, an oil
switch will stop the engine. Check oil level with dipstick.
Overload Reset — If the generator was overloaded, press

operating mode. The button also activates the hour meter.
See Hour Meter.

(generator load) of all the generator receptacles and

also flash to show generator hours. See Hour Meter.

switch to turn the QPT switch on (I) and off (0).
Rocker Switch Circuit Breaker — The receptacles are
provided with a 2 pole rocker switch circuit breaker to
protect the generator against electrical overload.
USB Ports — Use ports to recharge most USB powered
devices.
Main Breaker
120/240 Volt AC, 30 Amp

120 Volt AC, 20 Amp
GFCI Duplex Receptacles
Overload
Reset

Indicator
Compare the illustrations with your generator to familiarize yourself with the locations of various
controls and product warnings.
QPT Switch
USB Ports
Power Use

Circuit
Breakers
Not for
Reproduction
EN6 BRIGGSandSTRATTON.COM
Features and Controls
Muffler
Point away
from home
Not for
Reproduction
EN7
Operation
Operation

Before starting the portable generator there are two equally
important safety concerns regarding carbon monoxide
poisoning and fire that must be addressed.

Carbon Monoxide Poisoning
The engine exhaust of all fossil fuel burning equipment,
such as a portable generator, contains carbon monoxide,
a poisonous gas that could kill you in minutes. You cannot
smell it, see it, or taste it. Even if you do not smell exhaust
fumes, you could still be exposed to carbon monoxide gas.
By law it is required in many states to have a carbon
monoxide alarm in operating condition in your home. A
carbon monoxide alarm is an electronic device that detects
hazardous levels of carbon monoxide. When there is
a buildup of carbon monoxide, the alarm will alert the
occupants by flashing visual indicator light and alarm.
Smoke alarms cannot detect carbon monoxide gas.
DANGER! Engine exhaust contains carbon
monoxide, a poisonous gas that could kill you in
minutes. You cannot smell it, see it, or taste it.
Even if you do not smell exhaust fumes, you could still be
exposed to carbon monoxide gas.
Operate this product only outdoors far away from
windows, doors and vents to reduce the risk of carbon
monoxide gas from accumulating and potentially being
drawn towards occupied spaces.
Install battery-operated carbon monoxide alarms or
plug-in carbon monoxide alarms with battery back-up
according to the manufacturer’s instructions. Smoke
alarms cannot detect carbon monoxide gas.
Do not run this product inside homes, garages,
basements, crawlspaces, sheds, or other partially-
enclosed spaces even if using fans or opening doors
and windows for ventilation. Carbon monoxide can
quickly build up in these spaces and can linger for
hours, even after this product has shut off.
Always place this product downwind and point the
engine exhaust away from occupied spaces.
If you start to feel sick, dizzy, or weak while using this
product, get to fresh air right away. See a doctor. You may
have carbon monoxide poisoning.
Carbon monoxide alarm
Install carbon monoxide alarms inside
your home. Without working carbon
monoxide alarms, you will not realize
you are getting sick and dying from
carbon monoxide poisoning.
CARBON MONOXIDE ALARM(S)
USE OUTDOORS - AVOID CARBON MONOXIDE POISONING
point away
from home
MUFFLER


Not for
Reproduction
EN8 BRIGGSandSTRATTON.COM
Operation

WARNING!
Exhaust heat/gases could ignite
combustibles, structures or damage fuel tank
causing a fire, resulting in death or serious injury.
Portable generator must be at least 5 ft. (1.5 m) from
any structure, overhang, trees, windows, doors, any wall
opening, shrubs, or vegetation over 12 in. (30.5 cm) in
height.
Do not place portable generator under a deck or other
type of structure that may confine airflow. Smoke alarm(s)
must be installed and maintained indoors according to the
manufacturer’s instructions/recommendations.
Carbon monoxide alarms cannot detect smoke.
Do not place portable generator in manner other than
shown.
MUFFLER
5 ft. (1.5 m)
min.
5 ft. (1.5 m)
min.
Not for
Reproduction
EN9
Operation
Step 2: Oil and Fuel
Fuel must meet these requirements:
• Clean, fresh, unleaded fuel with a minimum of 87 octane.
Gasoline with an ethanol content up to 10% is acceptable.
E10
E15
NOTICE Do not mix oil in fuel or modify engine to run on
alternate fuels. Use of unapproved fuels could damage
engine and will not be covered under warranty.
See High Altitude for 5,000 ft. and above.
WARNING! Fuel and its vapors are extremely
flammable which could cause burns or fire
resulting in death or serious injury.
Do not refuel or move during operation.
Turn engine off and let it cool at least 2 minutes before
removing fuel cap.
Fill fuel tank outdoors. Keep fuel away from sparks, open
flames, pilot lights, heat, and other ignition sources.
Check fuel lines, tank, cap and fittings frequently for
cracks or leaks. Replace if necessary.
1. Move generator outdoors to a flat, level surface.
 
remove the side maintenance cover.
3. Clean area around oil fill and remove dipstick.
4. Using oil funnel, slowly pour oil into oil fill opening.
5. Checking oil level frequently, fill to full mark (top hole)
on dipstick.
NOTICE Pause to permit oil to settle. Wipe dipstick clean
each time oil level is checked. DO NOT overfill.
6. Replace and fully tighten dipstick.
7. Replace the maintenance cover and hand tighten the
three maintenance cover screws.
8. Slowly remove fuel cap to relieve pressure in tank.
9. Slowly add unleaded fuel to fuel tank. Be careful not
to fill above lip. This allows adequate space for fuel
expansion.
10. Install fuel cap and let any spilled fuel evaporate
before starting engine.

At altitudes over 5,000 ft. (1524 m), a minimum 85 octane
fuel is acceptable. To remain emissions compliant, high
altitude adjustment is required. Operation without this
adjustment will cause decreased performance, increased
fuel consumption,
and increased emissions.
See an authorized Briggs & Stratton dealer for high altitude
adjustment information. Operation of the engine at altitudes
below 2,500 ft. (762 m) with the high altitude kit is not
recommended.
Transporting
When transporting equipment with a vehicle or trailer,
turn engine switch to off (0) position. Do not tip engine or
equipment at an angle which causes fuel to spill.
NOTICE Do not lift or carry generator by retractable
handle. Handholds provided for convenient lifting.

The low oil indicator system is designed to prevent engine
damage caused by not enough engine oil. If the engine

indicator light comes on and an oil level switch will stop the

light comes on when you pull the recoil handle, check the
engine oil level.
Add
Full
Not for
Reproduction
EN10 BRIGGSandSTRATTON.COM
Step 3: Generator Start Up
NOTICE Always have QPT switch OFF (0) when starting or
stopping generator or when using DC USB ports.
Disconnect all electrical loads from the generator. Use the
following start instructions:
1. Make sure unit is outdoors on a level surface.
NOTICE Failure to operate the unit on a level surface may
cause the unit to shut down.
2. Pull choke control out to close choke ( ).
3. Turn engine switch to ON (I) position.
4. Grasp recoil starter handle and pull slowly until slight
resistance is felt. Then pull rapidly once to start engine.
5. Open choke gradually as engine warms up by pushing
in on choke handle.
NOTICE If engine fails to start, push choke control in and
repeat step 4. If engine starts but fails to run, see Low Oil
Indicator in Oil and Fuel.

Using Extension Cords
Use only grounded extension cords marked for outdoor
use rated for your loads. Follow cord safety instructions.
WARNING! Damaged or overloaded extension
cords could overheat, arc, and burn resulting in
death or serious injury.
NOTICE For generator output required see Generator
Capacity. Connect electrical loads in off position then turn
on for operation.
Power Use
The power use monitor indicates the percentage of total

the generator is operating normally or producing more than



Overload Reset

illuminates and cuts power to the receptacles. You
must turn off and unplug all electrical loads. Press the

and then plug in and restart electrical loads one at a time to
continue in normal operating mode.
5 Volt DC USB Ports
The maximum current available for the USB ports is 2.1
Amps at 5 Volts. The USB port allows you to recharge
most USB powered devices with a USB charging cable
(not included).
NOTICE For maximum output when charging Apple
devices, use the bottom USB port.
NOTICE For charging ITE (Information Technology
Equipment) only.
120 Volt AC, 20 Amp, GFCI Duplex Receptacles
Use each receptacle to operate 120 Volt AC, single-phase,
60 Hz electrical loads requiring up to 2,400 Watts (2.4 kW)
at 20 Amps of current.
Ground Fault Protection
The duplex receptacles are equipped with Ground Fault
Circuit Interrupter (GFCI) protection. The GFCI protects
against electrical shock that may be caused if your body
becomes a path which electricity travels to reach ground.
When protected by a GFCI, one may still feel a shock, but
the GFCI is intended to cut current off quickly enough so
that a person in normal health should not suffer any serious
electrical injury.
WARNING! Generator voltage could cause
electrical shock or burn resulting in death or
serious injury. Contact with the hot and neutral
conductor at the same time could cause electrical shock
or burn, even if the circuit is GFCI protected.
Testing the GFCI
Test your GFCI outlet prior to each use, as follows:
Push the “Test” button. The “Reset” button should pop
out, which should allow no power to reach the outlet.
Press the “Reset” button firmly until it is fully in place
and locks in that position. If the GFCI outlet does
not reset properly, do not use the outlet. Call or take
your generator to a local Briggs & Stratton authorized
service dealer.
If the GFCI trips by itself at any time, reset and test the
outlet.
Operation
Power Use

Overload
Reset
Recoil
Starter
Choke Control
Engine
Switch
USB
Ports
GFCI Duplex
Receptacles
Not for
Reproduction
EN11
Operation


4-wire cord set rated for 250 Volt AC loads at 30 Amps. The
generator’s locking receptacle is not protected by a GFCI.
This receptacle powers 120/240 Volt AC, 60 Hz, single
phase loads requiring up to 5,000 Watts of power (5.0kW)
at 20.8 Amps for 240 Volts or two independent 120 Volt
loads at 20.8 Amps each.
Generator Capacity
To make sure your generator can supply enough running
watts and starting watts for the items you will power at the
same time, follow these simple steps:
1. Select the items you will power at the same time. See
following list for typical wattages.
* Typical wattages listed are approximate only. Check tool
or appliance for actual wattage.
** Per Briggs & Stratton 628K, Starting Watts represents
the momentary electrical current the generator can
provide to start electric motors. Starting Watts does
not represent the power required to continuously run
electrical loads. Starting Watts is the maximum current
that can momentarily be supplied when starting a motor,
multiplied by the generator’s rated voltage.
2. Total the running watts. This is the amount of power
your generator must produce to keep your items
running. See following example:
Example
Total running watts = 2355
Highest starting watts = 2000
Total generator watts required = 4355
3. Estimate the starting watts you will need. Because not
all motors start at the same time, total starting wattage
can be estimated by adding only the item with the
highest additional starting watts requirements to the
total running watts from step 2.
Power Management
To manage generator power, sequentially add loads as
follows:
1. With nothing connected to generator, start the engine
outdoors.
2. Plug in and turn on the first load, preferably the largest
load you have.
3. Permit the generator output to stabilize (engine runs
smoothly and attached device operates properly).
4. Plug in and turn on the next load.
5. Again, permit the generator to stabilize.
6. Repeat steps 4 and 5 for each additional load.
Never add more loads than the generator capacity. Take
special care to consider surge loads in generator capacity.
Step 5: Generator Shutdown
1. Turn off and unplug all electrical loads from generator
panel receptacles. Never stop engine with electrical
devices plugged in and turned on.
 
internal temperatures of engine and generator.
3. Turn engine switch to 0FF (0) position.
4-Wire Cord Set
240V
120V
W (Neutral)
X (Hot)
Y (Hot)
Ground (Green)
120V

Tool or Appliance Running Watts Starting Watts
Window air conditioner
1200 1800
Refrigerator 800 2000
Television 280
 75
2355 Total
Running Watts
2000 Highest
Starting Watts
Tool or Appliance
Running
Watts*
Starting
Watts**
 75 -
Sump Pump 800 1200
Refrigerator/Freezer 800 2000
Water Well Pump - 1/3 HP 1000 2000
Window AC - 10,000 BTU 1200 1800
Furnace Fan Blower - 1/2 HP 800 1300
Microwave Oven - 1000 Watt 1000 -
Color Television - 42” 280 -
Personal Computer w/17” monitor 800 -
Garage Door Opener - 1/2 HP 480 520
Not for
Reproduction
EN12 BRIGGSandSTRATTON.COM
Maintenance
Maintenance
Maintenance Schedule
Follow the hourly or calendar intervals, whichever occurs
first. More frequent service is required when operating in
adverse conditions noted below.
1
Service more often under dirty or dusty conditions.
General Recommendations
Regular maintenance will improve the performance and
extend the life of the generator. See any authorized dealer
for service.
The generator’s warranty does not cover items that have
been subjected to operator abuse or negligence. To
receive full value from the warranty, the operator must
maintain the generator as instructed in this manual.
All service and adjustments should be made at least once
each season. A new spark plug and clean air filter assure
proper fuel-air mixture and help your engine run better and
last longer. Follow requirements in Maintenance Schedule.
Emissions Control
Maintenance, replacement, or repair of the emissions
control devices and systems may be performed by any
non-road engine repair establishment or individual.
However, to obtain ”no charge” emissions control service,
the work must be performed by a factory authorized dealer.
See Emissions Warranty.


and indicates the amount of hours the generator has

RESET button for 3 seconds.


how many digits will display. OK represents the first digit,
25% the second digit, 75% the third digit, and 100% the

with a zero will remain lit.
Example
 OK
First Digit
25%
Second
Digit
75%
Third Digit
100%
Fourth
Digit
2 Hours Off Off Off Blink x 2
47 Hours Off Off Blink x 4 Blink x 7
108 Hours Off Blink x 1 On Blink x 8
1264 Hours Blink x 1 Blink x 2 Blink x 6 Blink x 4
Cleaning
Daily or before use, look around and underneath
the generator for signs of oil or fuel leaks. Clean any
accumulated debris. Keep area around muffler free from
any debris.
Use a soft bristle brush to loosen caked on dirt or oil.
Use a damp cloth to wipe exterior surfaces clean.
NOTICE Improper treatment of generator could damage
it and shorten its life. Do not expose generator to excessive
moisture, dust, dirt, or corrosive vapors. Do not insert any
objects through cooling slots.
Engine Maintenance
Oil Recommendations
We recommend the use of Briggs & Stratton Warranty
Certified oils for best performance. Other high-quality
detergent oils are acceptable if classified for service SF
or higher. Do not use special additives. See Common
Service Parts.
Outdoor temperatures determine the proper oil viscosity for
the engine. Use the chart to select the best viscosity for the
outdoor temperature range expected.
* Below 40°F (4°C) the use of SAE 30 will result in hard starting.
** Above 80°F (27°C) the use of 10W30 may cause increased oil
consumption. Check oil level more frequently.

Change engine oil

Clean debris
Check engine oil level

Clean engine air filter
1

Inspect muffler and spark arrester

Change engine oil
1
Yearly
Replace engine air filter
1
Replace spark plug
Not for
Reproduction
EN13
Maintenance

Oil level should be checked prior to each use or at least
every 8 hours of operation. Keep oil level maintained.
1. Make sure generator is on a level surface.
 
remove the side maintenance cover.
3. Clean area around oil fill, remove dipsitck and wipe
with clean cloth. Replace dipstick. Remove and check
oil level.
4. Verify oil is at full mark (top hole) on dipstick.
5. If needed, using oil funnel, slowly pour oil into oil fill
opening to full mark (top hole) on dipstick. Do not overfill.
NOTICE Overfilling with oil could cause the engine to not
start, or hard starting.
Do not overfill.
If over the full mark (top hole) on dipstick, drain oil to reduce
oil level to full mark on dipstick.
6. Replace and tighten dipstick.
7. Replace the side maintenance cover and hand tighten
the three maintenance cover screws.
NOTICE Do not attempt to crank or start engine before
it has been properly serviced with recommended oil. This
could result in an engine failure.
CAUTION Avoid prolonged or repeated skin contact
with used motor oil. Used motor oil has been shown
to cause skin cancer in certain laboratory animals.
Thoroughly wash exposed areas with soap and water.



Changing Engine Oil
If you are using your generator under extremely dirty or
dusty conditions, or in extremely hot weather, change the
oil more often.
Change oil while engine is still warm from running, as follows:
1. Make sure unit is on a level surface.
2. Remove oil drain plug and drain oil completely into a
suitable container.
3. Reinstall oil drain plug and tighten securely.
 
remove the side maintenance cover.
5. Clean area around oil fill, remove dipsitck and wipe
with clean cloth.
6. Slowly pour recommended oil (about 36 oz. (1.0 l))
into oil fill opening. Pause to permit oil to settle. Fill to
full mark (top hole) on dipstick.
7. Wipe dipstick clean each time oil level is checked. Do
not overfill.
8. Reinstall dipstick.
9. Wipe up any spilled oil.
10. Replace the side maintenance cover and hand tighten
the three maintenance cover screws.
Service Air Filter
Your engine will not run properly and may be damaged if
you run it with a dirty air filter. Clean or replace more often
if operating under dusty or dirty conditions.
 
2. Carefully remove foam filter by pulling it out towards
you.
3. Wash foam filter in liquid detergent and water only.
Squeeze dry in a clean cloth.
4. SATURATE foam air filter in clean engine oil and
squeeze in a clean cloth to remove excess oil.
5. Reinstall clean or new foam filter inside base behind
face plate.
NOTICE Be sure filter is fully seated behind the face
plate.
6. Slide back cover into grove and reinstall.
Oil Drain
Plug
Add
Full
Filter
Face Plate
Not for
Reproduction
EN14 BRIGGSandSTRATTON.COM
Maintenance

Changing the spark plug will help your engine to start
easier and run better.
 
remove the side maintenance cover.
2. Clean area around spark plug and remove spark plug
boot.
3. Remove spark plug and inspect spark plug.
4. Replace spark plug if electrodes are pitted, burned
or porcelain is cracked. Use the recommended
replacement plug. See Common Service Parts.
5. Check electrode gap with wire feeler gauge and reset
spark plug gap to recommended gap if necessary.
See Specifications.
6. Install spark plug and tighten firmly. Reinstall spark
plug boot.
7. Replace the side maintenance cover and hand tighten
the three maintenance cover screws.

The engine exhaust muffler has a spark arrester screen.
Inspect the muffler for cracks, corrosion, or other damage.
Inspect spark arrester screen for damage or carbon
blockage. Clean if carbon blockage is found or replace if
damaged. If replacement parts are required, make sure to
use only original equipment replacement parts.
WARNING!
Contact with muffler area could
cause burns resulting in serious injury.
Do not touch hot parts.
It is a violation of California Public Resource Code,
Section 4442, to use or operate the engine on any forest-
covered, brush-covered, or grass-covered land unless
the exhaust system is equipped with a spark arrester, as
defined in Section 4442, maintained in effective working
order. Other states or federal jurisdictions may have
similar laws, reference Federal Regulation 36 CFR Part
261.52.

 
remove the side maintenance cover.
2. Remove screw that attaches spark arrester screen to
muffler. Remove spark arrester screen.
3. Obtain a replacement screen. See Common Service
Parts.
4. Reattach screen to muffler. Reattach side cover.
Common Service Parts
Air Cleaner .............................596106
Spark Plug .............................798615
Engine Oil Bottle ...............100005 or 100028
Synthetic Oil Bottle ......................100074
Fuel Stabilizer .................100120 or 100117
Contact an authorized service dealer or
BRIGGSandSTRATTON.COM for a full list of parts and
diagrams.
Screw
Spark
Arrester
Not for
Reproduction
EN15
Storage
Storage
If storing the unit for more than 30 days, use the following
guidelines to prepare it for storage.

1. Clean the generator as outlined in Cleaning.
2. Change engine oil while engine is still warm, drain oil
from crankcase. Refill with recommended grade. See
Changing Engine Oil.
3. Treat or drain fuel from generator as fuel can become
stale when stored over 30 days.
Stale fuel causes acid and gum deposits to form in the fuel
system or on essential carburetor parts. To keep fuel fresh,
use Briggs & Stratton® Advanced Formula Fuel Treatment
& Stabilizer, available wherever Briggs & Stratton genuine
service parts are sold. See Common Service Parts.
There is no need to drain gasoline from the engine if a
fuel stabilizer is added according to instructions. Run the
engine for 2 minutes to circulate the stabilizer throughout
the fuel system before storage.
If gasoline in the engine has not been treated with a fuel
stabilizer, it must be drained into an approved container.
Run the engine until it stops from lack of fuel. The use of a
fuel stabilizer in the storage container is recommended to
maintain freshness.
WARNING!
Fuel and its vapors are extremely
flammable and explosive which could cause
burns, fire or explosion resulting in death or
serious injury.
When storing fuel or equipment with fuel in tank, store
away from furnaces, stoves, water heaters, clothes dryers
or other appliances that have pilot light or other ignition
source because they could ignite fuel vapors.
When draining fuel, turn generator engine off and let it

cap slowly to relieve pressure in tank. Drain fuel tank
outdoors. Keep fuel away from sparks, open flames, pilot
lights, heat, and other ignition sources.
Check fuel lines, tank, cap and fittings frequently for
cracks or leaks. Replace if necessary.
4. Store generator in clean, dry area and cover with a
suitable protective cover that does not retain moisture.
WARNING! Storage covers could cause a fire
resulting in death or serious injury.

equipment cool for a sufficient time before placing the
cover on the equipment.
Not for
Reproduction
EN16 BRIGGSandSTRATTON.COM
Troubleshooting/Specifications
Specifications
Running Watts* ...........................5,000
Starting Watts** ...........................6,500
AC Current at 240 Volts ............... 20.8 Amps
AC Current at 120 Volts ............... 41.6 Amps
Frequency. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60 Hz
Phase ............................ Single Phase
Displacement ................18.67 cu. in. (306 cc)
Spark Plug Gap ...............0.030 in. (0.76 mm)
Fuel Capacity ...........
Oil Capacity ................
Power Ratings: The gross power rating for individual gasoline engine models is labeled in accordance with SAE (Society of Automotive
Engineers) code J1940 Small Engine Power & Torque Rating Procedure, and is rated in accordance with SAE J1995. Torque values are
derived at 2600 RPM for those engines with “rpm” called out on the label and 3060 RPM for all others; horsepower values are derived
at 3600 RPM. The gross power curves can be viewed at www.BRIGGSandSTRATTON.COM. Net power values are taken with exhaust
and air cleaner installed whereas gross power values are collected without these attachments. Actual gross engine power will be higher
than net engine power and is affected by, among other things, ambient operating conditions and engine-to-engine variability. Given the
wide array of products on which engines are placed, the gasoline engine may not develop the rated gross power when used in a given
piece of power equipment. This difference is due to a variety of factors including, but not limited to, the variety of engine components
(air cleaner, exhaust, charging, cooling, carburetor, fuel pump, etc.), application limitations, ambient operating conditions (temperature,
humidity, altitude), and engine-to engine variability. Due to manufacturing and capacity limitations, Briggs & Stratton may substitute an
engine of higher rated power for this engine.
* Generator certified in accordance with CSA (Canadian Standards Association) standard C22.2 No. 100-14, Motors and Generators
and PGMA (Portable Generator Manufacturers’ Association) standard ANSI/PGMA G300-2015, Safety and Performance of Portable
Generators.
** Per Briggs & Stratton 628K
Problem Cause Correction
Engine is running, but no AC
output is available.
 
overloaded or overheated.
2. Poor connection or defective cord set.
3. Connected device is bad.
1. See Generator Capacity. Press

control panel.
2. Check and repair.
3. Connect another device that is in
good condition.

“bogs down” when loads are
connected.
1. Generator is overloaded. 1. See Generator Capacity.
Engine will not start; starts
and runs rough or shuts down
when running.
1. Engine switch in OFF (0) position.
 
oil level.
3. Dirty air filter.
4. Out of fuel.
5. Spark plug wire not connected to
spark plug.
6. Flooded with fuel.
1. Turn engine switch to ON (I) position.
2. Fill crankcase to proper level or place
generator on level surface.
3. Clean or replace air filter.
4. Fill fuel tank.
5. Connect wire to spark plug.
6. Wait 5 minutes and re-crank engine.
For all other issues, see a Briggs & Stratton authorized dealer.
Not for
Reproduction
EN17
Troubleshooting
Not for
Reproduction
EN18 BRIGGSandSTRATTON.COM
Warranty
80011053_EN Rev. A


Briggs & Stratton warrants that, during the warranty period specified below, it will repair or replace, free of charge, any part that is defective in material or workmanship
or both. Transportation charges on product submitted for repair or replacement under this warranty must be borne by purchaser. This warranty is effective for
and is subject to the time periods and conditions stated below. For warranty service, find the nearest Authorized Service Dealer in our dealer locator map at
BRIGGSandSTATTON.COM. The purchaser must contact the Authorized Service Dealer, and then make the product available to the Authorized Service Dealer for
inspection and testing.
There is no other express warranty. Implied warranties, including those of merchantability and fitness for a particular purpose, are limited to the
warranty period listed below, or to the extent permitted by law. 
is permitted by law. Some states or countries do not allow limitations on how long an implied warranty lasts, and some states or countries do not allow the exclusion
or limitation of incidental or consequential damages, so the above limitation and exclusion may not apply to you. This warranty gives you specific legal rights and you
may also have other rights which vary from state to state or country to country.**
WARRANTY PERIOD
After 12 months, warranty covers parts only.
* Applies to Briggs & Stratton engines only. Warranty coverage of non-Briggs & Stratton engines is provided by that engine manufacturer. Emissions-related components
are covered by the Emissions Warranty Statement.
**
failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be
of acceptable quality and the failure does not amount to a major failure. For warranty service, find the nearest Authorized Service Dealer in our dealer locator map at

Moorebank Avenue, NSW, Australia, 2170.
The warranty period begins on the date of purchase by the first retail or commercial consumer. “Consumer use” means personal residential household use by a retail
consumer. “Commercial use” means all other uses, including use for commercial, income producing or rental purposes. Once a product has experienced commercial
use, it shall thereafter be considered as a commercial use product for purposes of this warranty.
Save your proof of purchase receipt. If you do not provide proof of the initial purchase date at the time warranty service is requested, the manufacturing date of the
product will be used to determine the warranty period. Product registration is not required to obtain warranty service on Briggs & Stratton products.
ABOUT YOUR WARRANTY
Warranty service is available only through Briggs & Stratton Authorized Service Dealers. This warranty covers only defects in materials or workmanship. It does not cover
damage caused by improper use or abuse, improper maintenance or repair, normal wear and tear, or stale or unapproved fuel.
Improper Use and Abuse - The proper, intended use of this product is described in the Operator’s Manual. Using the product in a way not described in the Operator’s
Manual or using the product after it has been damaged will not be covered under this warranty. Warranty coverage will also not be provided if the serial number on the
product has been removed or the product has been altered or modified in any way, or if the product has evidence of abuse such as impact damage or water/chemical
corrosion damage.
Improper Maintenance or Repair - This product must be maintained according to the procedures and schedules provided in the Operator’s Manual, and serviced or
repaired using genuine Briggs & Stratton parts or equivalent. Damage caused by lack of maintenance or use of non-original parts is not covered by warranty.
Normal Wear and Tear
use has exhausted the life of a part or the equipment. Maintenance and wear items such as filters, belts, cutting blades, and brake pads (except engine brake pads) are
not covered by warranty due to wear characteristics alone, unless the cause is due to defects in material or workmanship.
Stale or Unapproved Fuel - In order to function correctly, this product requires fresh fuel that conforms to the criteria specified in the Operator’s Manual. Engine or
equipment damage caused by stale fuel or the use of unapproved fuels (such as E15 or E85 ethanol blends) is not covered by warranty.
This warranty excludes damage due to accident, abuse, modifications, alterations, improper servicing, freezing or chemical deterioration.
Attachments or accessories that were not originally packaged with the product are also excluded. There is no warranty coverage on equipment used for primary power in
place of utility power or on equipment used in life support applications. This warranty does not include used, reconditioned, second-hand, or demonstration equipment or
engines. This warranty also excludes failures due to acts of God and other force majeure events beyond the manufacturer’s control.
Item Consumer Use Commercial Use
Equipment 24 months 12 months
Engine* 24 months 12 months
Battery (if equipped) 3 months None
Not for
Reproduction
Generador tipo inversor
para exteriores
Manual del operador
Número de modelo __________________________
Revisión __________________________________
Número de serie ____________________________
Fecha de adquisición ________________________
Copyright © 2017. Briggs & Stratton Corporation
Milwaukee, WI, EE. UU. Todos los derechos reservados.
800-743-4115
BRIGGSandSTRATTON.COM
Not for
Reproduction
ES2 BRIGGSandSTRATTON.COM
Índice
Descripción del equipo.........................2
Características y controles......................5
Operación ...................................7
Mantenimiento ..............................13
Almacenamiento.............................16
Solución de problemas/Especificaciones.........17
Garantía....................................18
Registre su producto
Con el fin de garantizar la cobertura de la garantía de
forma oportuna y completa, registre su producto en línea
en www.onlineproductregistration.com.
Símbolos y advertencias
Señal Advertencias

Indica un peligro que, si no se evita,
ocasionará la muerte o lesiones graves.
ADVERTENCIA
Indica un peligro que si no es evitado,
podría ocasionar la muerte o heridas
graves.
PRECAUCIÓN
Indica un peligro que, si no se evita,
podría ocasionar lesiones menores o
moderadas.
AVISO
Indica una información considerada
importante, pero no relacionada con un
peligro.
Símbolo Nombre Explicación
Símbolo de
alerta de
seguridad
Indica un posible riesgo para su
integridad física.
Manual del
operador
El no cumplir con leer y seguir las
advertencias, las instrucciones y
el manual del operador podrían
dar como resultado la muerte o
lesiones graves.
Gases
Tóxicos
El escape del motor contiene
monóxido de carbono, un gas
tóxico que puede matar en
minutos. No puede olerlo ni verlo.
Incendio
El combustible y sus vapores son
extremadamente inflamables, lo
que podría causar quemaduras
o incendios que conlleven la
muerte o lesiones graves.
El escape del motor puede
causar un incendio que conlleve
la muerte o lesiones graves.
Descarga
eléctrica
El generador podría provocar
electrocución que conlleve
lesiones graves o la muerte.
Símbolo Nombre Explicación
Superficie
caliente
El silenciador puede causar
quemaduras que podrían
comportar lesiones graves.
¡ADVERTENCIA! Este producto puede
exponerlo a sustancias químicas entre las que
se incluyen emisiones de escape de motor de
gasolina, reconocidas por el Estado de California como
causantes de cáncer; y monóxido de carbono, reconocido
por el Estado de California como causante de defectos de
nacimiento u otros problemas reproductivos. Para obtener
más información, visite www.P65Warnings.ca.gov.
Descripción del equipo

el generador para exteriores. Conozca sus
aplicaciones, sus limitaciones y cualquier riesgo
implicado. Conserve estas instrucciones originales para
futuras consultas.
Esta unidad es un generador de corriente alterna y continua
(CA y CC) de campo giratorio accionado por motor. Suministra
energía eléctrica para iluminación, electrodomésticos,
herramientas y cargas de motores eléctricos. El campo
giratorio del generador funciona a unas 3600 rpm (con suiche

accionado por un motor de un solo cilindro.
El generador para exteriores produce energía que puede usarse
para dispositivos en el exterior mediante cables de extensión o
para restaurar la energía del hogar temporalmente por primera
vez. Antes del próximo corte de energía en su hogar, instale
uno de los suiches de transferencia que aparecen en la lista.
Un suiche de transferencia es un dispositivo independiente que
instala un electricista con licencia para conectar el generador
portátil con cables, mediante una toma de bloqueo, directamente
al sistema eléctrico de su hogar. No se supone que los cables
de extensión conectados al panel de control del generador
portátil sean una solución a largo plazo cuando se conectan con
dispositivos dentro del hogar.
Se ha realizado el máximo esfuerzo para garantizar que la
información de este manual sea precisa y esté actualizada. No
obstante, el fabricante se reserva el derecho de modificar, alterar
o mejorar de cualquier otra forma el generador y este documento
en cualquier momento y sin previo aviso.
AVISO Si tiene alguna pregunta acerca del uso previsto,
póngase en contacto con el distribuidor autorizado. Este equipo
se ha diseñado para usarse con partes autorizadas de Briggs &
Stratton únicamente.
Este sistema de encendido por chispa cumple con la
norma canadiense ICES-002.
Descripción del equipo
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56

Simplicity 030735-00 Manuel utilisateur

Catégorie
Groupes électrogènes
Taper
Manuel utilisateur
Ce manuel convient également à