3com SuperStack 3 3C16410 Manuel utilisateur
- Catégorie
- Commutateurs réseau
- Taper
- Manuel utilisateur
Ce manuel convient également à
The SuperStack
®
3 Baseline 10/100 Switch is a versatile,
easy-to-use unmanaged switch. It is ideal for users who want the
high-speed performance of 10/100 switching but do not need
sophisticated management capabilities. The Baseline 10/100
Switch is shipped ready for use. No configuration is necessary.
The Baseline 10/100 Switch has 16 or 24 shielded RJ-45,
10/100 Mbps auto-negotiating ports on the front panel. Each port
automatically determines the speed and duplex mode of the
connected equipment and provides a suitable switched
connection. Each port also supports automatic MDI/MDI-X
detection.
The Baseline 10/100 Switch is suited for office use where it can
be free standing, or rack mounted (in a wiring closet or
equipment room).
The Baseline 10/100 Switch comes with:
One power cord for use with the Baseline 10/100 Switch
Four self-adhesive rubber pads
One mounting kit
The Switch is powered from the AC mains supply.
The Baseline 10/100 Switch provides high performance switched
connections to 10 Mbps and 100 Mbps hubs, servers and
workstations that require a dedicated switched link.
The diagram below shows an sample configuration:
INTRODUCTION
Endstations on shared
100Mbps connections
Baseline Dual Speed Hub
100Mbps link10Mbps link
100Mbps connection
to backbone
Endstations on switched
10Mbps connections
Baseline 10/100 Switch
Endstations on shared
10Mbps connections
Baseline Hub
SuperStack
®
3 Baseline 10/100 Switch 16-Port (3C16470) and 24-Port
(3C16471) User Guide
DUA1647-0AAA01
1
13
12
16
17
20
24
21
4
8
9
5
1
Numbered elements in this diagram refer to numbered sections in
the text. A 24-port unit is shown.
Front Panel
1 24 RJ-45 10/100 Ports
WARNING
: RJ-45 ports. These are shielded RJ-45 data
sockets. They cannot be used as standard traditional
telephone sockets, or to connect the unit to a traditional
PBX or public telephone network. Only connect RJ-45
data connectors, network telephony systems, or network
telephones to these sockets. Either shielded or unshielded
data cables with shielded or unshielded jacks can be
connected to these data sockets.
AVERTISSEMENT: Les ports RJ-45. Ceux-ci sont
protégés par des prises de données. Ils ne peuvent pas
être utilisés comme prises de téléphone conventionnelles
standard, ni pour la connection de l’unité à un réseau
téléphonique central privé ou public. Raccorder seulement
connecteurs de données RJ-45, systèmes de réseaux de
téléphonie ou téléphones de réseaux à ces prises. Il est
possible de raccorder des câbles protégés ou non
protégés avec des jacks protégés ou non protégés à ces
prises de don.
WARNUNG: RJ-45-Porte. Diese Porte sind geschützte
Datensteckdosen. Sie dürfen weder wie normale
traditionelle Telefonsteckdosen noch für die Verbindung
der Einheit mit einem traditionellem privatem oder
öffentlichem Telefonnetzwerk gebraucht werden. Nur
RJ-45-Datenanscluße, Telefonnetzsysteme or Netztelefone
an diese Steckdosen anschließen. Entweder geschützte
oder ungeschützte Buchsen dürfen an diese
Datensteckdosen angeschlossen werden.
10BASE-T/100BASE-TX Ports
The Baseline 10/100 Switch has 16 (3C16470) or 24
(3C16471) 10/100 Mbps auto-negotiating ports.
To connect a device to the Baseline 10/100 Switch, use
Category 5 unshielded or shielded (screened) 100 Ohm
TP cable (or Category 3 cable for a 10 Mbps connection).
The maximum length of cable for each connection is
100m (328ft). Connect one end of the cable to an RJ-45
port on the Baseline 10/100 Switch, and the other end to
the appropriate RJ-45 port on the connecting device.
Each port on the Baseline 10/100 Switch is
auto-negotiating: its speed and duplex mode (half duplex
or full duplex) are automatically determined by the
capabilities of the connected device.
Each port supports automatic MDI/MDI-X detection and
can be connected to either a 10BASE-T or a 100BASE-TX
device.
The Switch offers priority queuing, which means all
packets that are received are examined to see if they have
been priority encoded. If a packet has been then the
Switch will read the priority level and determine whether
the packet should be directed through the normal or high
priority channel. This feature can be useful for example
during excessive loads when one type of traffic may
require priority over another. The Switch is configured to
comply with 802.1p, VLAN tagged frames.
Traffic prioritization ensures that high priority data is
forwarded through the Switch without being delayed by
lower priority data. It differentiates traffic into classes and
prioritizes those classes automatically. Traffic prioritization
uses the multiple traffic queues that are present in the
hardware of the Switch to ensure that high priority traffic
is forwarded on a different queue from lower priority
traffic, and is given preference over that traffic. This
ensures that time-sensitive traffic gets the highest level of
service. The 802.1D standard specifies eight distinct levels
of priority (0 to 7), each of which relates to a particular
type of traffic. The priority levels and their traffic types
are shown in the following table.
The traffic prioritization feature supported by the Switch
is compatible with the relevant sections of the IEEE
802.1D standard (incorporating IEEE 802.1p).
If you connect two Baseline 10/100 Switch units together,
the link between them operates at 100 Mbps full duplex.
You must use Category 5 cable when connecting the
units.
HOW TO USE THE BASELINE 10/100 SWITCH
1
2
3
4
6
5
16
1
13
4
17
5
8
20
9
12
21 24
Priority Level Traffic Type
0 Best Effort
1 Background
2 Standard (spare)
3 Excellent Effort (business critical)
4 Controlled Load (streaming multimedia)
5 Video (Interactive media), less than 100
millisecondsn latency and jitter.
6 Voice (Interactive voice), less than 10
milliseconds latency and jitter.
7 Network Control Reserved traffic
2
CAUTION: The Baseline 10/100 Switch supports full
duplex auto-negotiation. If the connected device does not
support auto-negotiation, the Switch will operate in half
duplex mode (even if the device is operating in full duplex
mode). In such a configuration, you may notice some
degradation of network performance. 3Com recommends
that you use devices that are capable of auto-negotiation
(and that you ensure that auto-negotiation is enabled, if
it is a configurable option).
2
Activity/Link/Speed Status LEDs
The first (top) and third row of LEDs, which are colored yellow or
green, show the activity and speed status of the related ports:
3
Duplex Status LEDs
The second and fourth (bottom) row of Status LEDs, which are
colored yellow, show the duplex status of the related ports:
4
Power LED
The Power LED shows the power status of the Switch:
5
Self-adhesive Pads
The unit is supplied with four self-adhesive rubber pads.
You do not need to apply the pads if you intend to rack
mount the unit.
If the unit is to be part of a free standing stack, apply the pads to
each marked corner area on the underside of the unit. Place the
unit on top of the lower unit, ensuring that the pads locate with
the recesses of the lower unit.
Rear Panel Connections
6 Power Supply
The Baseline 10/100 Switch automatically adjusts to the supply
voltage. Only use the power cord that is supplied with the
Baseline 10/100 Switch.
Positioning the Baseline 10/100 Switch
CAUTION: If installing the Baseline 10/100 Switch in a
stack of different size SuperStack 3 units, the smaller
units must be installed above the larger ones. Do not
have a free-standing stack of more than six units.
When deciding where to position the Baseline 10/100 Switch
ensure that:
It is accessible and cables can be connected easily.
Cabling is away from sources of electrical noise such as
radios, transmitters and broadband amplifiers, and away from
power lines and fluorescent lighting fixtures.
The Switch is situated away from sources of electrically
conductive dust, for example laser printers.
The AC supply used by the Switch is separate to those used
by units that generate high levels of AC noise, for example air
conditioning units and laser printers.
Water or moisture cannot enter the case of the unit.
Air flow around the unit and through the vents in the side of
the case is not restricted (3Com recommends that you
provide a minimum of 25 mm (1 in.) clearance).
To prolong the operational life of your units:
Never stack units more than six high if free-standing, and
ensure that cables are supported so that they do not cause
the stack to fall over.
Do not place objects on top of any unit or stack.
Do not obstruct any vents at the sides of the case.
Rack Mounting
The Baseline 10/100 Switch can be mounted in a 19-inch
equipment rack using the Mounting Kit. Refer to “Mounting Kit
Instructions” on page 5.
Power Up
Use the following sequence to power up the Baseline 10/100
Switch:
1 Check the network connections and cables.
2 Connect the power supply cable to the appropriate power
socket on the rear panel of the unit; refer to 6 Power
Supply
.
3 Connect the plug to the power supply outlet socket and
switch on the power supply at the socket.
When the switch is powered on, the Power LED should be lit on
green. If it is not, refer to 4 Power LED.
Spot Checks
At frequent intervals you should visually check the Baseline
10/100 Switch. Regular checks can give you an early warning of a
possible failure; any problems can then be attended to when
there will be least effect on users. Check that all external cabling
connections are secure and that no cables are pulled taut.
If you experience any problems operating the Baseline 10/100
Switch, refer to “Problem Solving” on page 5.
Status Meaning
On The link has been established.
Flashing Packets are being received or transmitted on the port.
Off If the link has not been established, either nothing is
connected to the port, or there is a problem:
■ Check that the attached device is powered on.
■ Check that the cable is the correct type and is not faulty.
If these checks do not identify the cause of the problem, it
may be that the unit or the device connected to the port is
faulty. Contact your supplier for further advice.
Green The link is operating at 100 Mbps.
Yellow The link is operating at 10 Mbps.
!
Status Meaning
On Yellow The port is operating in full-duplex mode.
Off The port is operating in half-duplex mode.
Status Meaning
On Green The unit is powered on and ready for use.
Off The unit is not receiving power:
■ Check the power cord is connected correctly.
■ If the unit still does not operate, contact your supplier.
INSTALLING THE SWITCH
!
3
Please read the following safety information carefully before
installing the Baseline 10/100 Switch.
WARNING: Installation and removal of the unit must be carried out
by qualified personnel only.
If installing the Switch unit in a stack with other SuperStack 3 units,
the Baseline 10/100 Switch unit must be installed below the narrower
Hub units.
The unit must be connected to an earthed (grounded) outlet to comply
with international safety standards.
Do not connect the unit to an A.C. outlet (power supply) without an
earth (ground) connection.
The appliance coupler (the connector to the unit and not the wall plug)
must have a configuration for mating with an EN60320/IEC320
appliance inlet.
The socket outlet must be near to the unit and easily accessible. You
can only remove power from the unit by disconnecting the power cord
from the outlet.
This unit operates under SELV (Safety Extra Low Voltage) conditions
according to IEC 60. The conditions are only maintained if the
equipment to which it is connected also operates under SELV
conditions.
France and Peru only
This unit cannot be powered from IT
†
supplies. If your supplies are of IT type, this
unit must be powered by 230V (2P+T) via an isolation transformer ratio 1:1, with
the secondary connection point labelled Neutral, connected directly to earth
(ground).
†
Impédance à la terre
Power Cord Set
This must be approved for the country where it will be used. e.g.
Veuillez lire à fond l'information de la sécurité suivante avant
d'installer le Baseline 10/100 Switch .
AVERTISSEMENT: L’installation et la dépose de ce groupe doivent
être confiés à un personnel qualifié.
Si vous entassez l’unité Switch avec les unités SuperStack 3, l’unité
Baseline 10/100 Switch doit être installée en dessous des unités Hub
plus étroites.
Ne branchez pas votre appareil sur une prise secteur (alimentation
électrique) lorsqu'il n'y a pas de connexion de mise à la terre (mise à la
masse).
Vous devez raccorder ce groupe à une sortie mise à la terre (mise à la
masse) afin de respecter les normes internationales de sécurité.
Le coupleur d’appareil (le connecteur du groupe et non pas la prise
murale) doit respecter une configuration qui permet un branchement
sur une entrée d’appareil EN60320/IEC 320.
La prise secteur doit se trouver à proximité de l’appareil et son accès
doit être facile. Vous ne pouvez mettre l’appareil hors circuit qu’en
débranchant son cordon électrique au niveau de cette prise.
L’appareil fonctionne à une tension extrêmement basse de sécurité qui
est conforme à la norme IEC60950. Ces conditions ne sont maintenues
que si l’équipement auquel il est raccordé fonctionne dans les mêmes
conditions.
Branchez uniquement un Advanced Redundant Power System
(3C16070, 3C16071, 3C16071A ou 3C16071B) ou un Redundant
Power System (3C565047) sur la prise femelle du Redundant Power
System.
France et Pérou uniquement:
Ce groupe ne peut pas être alimenté par un dispositif à impédance à la terre. Si vos
alimentations sont du type impédance à la terre, ce groupe doit être alimenté par
une tension de 230 V (2 P+T) par le biais d’un transformateur d’isolement à rapport
1:1, avec un point secondaire de connexion portant l’appellation Neutre et avec
raccordement direct à la terre (masse).
Cordon électrique
Il doit être agréé dans le pays d’utilisation.
Bitte unbedingt vor dem Einbauen des Baseline 10/100 Switch
Einheit die folgenden Sicherheitsanweisungen durchlesen.
WARNUNG: Die Installation und der Ausbau des Geräts darf nur
durch Fachpersonal erfolgen.
Wenn die Baseline 10/100 Switch Einheit in einer Stapel mit anderen
SuperStack 3 Einheiten eingebaut werden soll, muß die Baseline
10/100 Switch Einheit unter die schmaleren Hub Einheiten eingebaut
werden.
Das Gerät nicht an eine Wechselstromsteckdose anschließen, die nicht
geerdet ist.
Das Gerät muß an eine geerdete Steckdose angeschlossen werden, die
die internationalen Sicherheitsnormen erfüllt.
Der Gerätestecker (der Anschluß an das Gerät, nicht der
Wandsteckdosenstecker) muß eine passende Konfiguration für einen
Geräteeingang gemäß EN60320/IEC320 haben.
Die Netzsteckdose muß in der Nähe des Geräts und leicht zugänglich
sein. Die Stromversorgung des Geräts kann nur durch Herausziehen
des Gerätenetzkabels aus der Netzsteckdose unterbrochen werden.
Der Betrieb dieses Geräts erfolgt unter den SELV-Bedingungen
(Sicherheitskleinstspannung) gemäß IEC 60. Diese Bedingungen sind nur
gegeben, wenn auch die an das Gerät angeschlossenen Geräte unter
SELV-Bedingungen betrieben werden.
Nur ein Advanced Redundant Power System (3C16070, 3C16071,3C16071A
oder 3C16071B) oder Redundant Power System (3C565047) an den
Redundant Power System Anschluß anschließen.
SAFETY INFORMATION
U.S.A. and
Canada
■ The cord set must be UL-approved and CSA certified.
■ The minimum specifications for the flexible cord are:
No. 18 AWG
Type SV or SJ
3-conductor
■ The cord set must have a rated current capacity of at least
10A.
■ The attachment plug must be an earth-grounding type
with a NEMA 5-15P (15 A, 125 V) or NEMA 6-15P (15 A,
250 V) configuration.
Denmark
■ The supply plug must comply with Section 107-2-D1,
Standard DK2-1a or DK2-5a.
Switzerland
■ The supply plug must comply with SEV/ASE 1011.
UK
■ The supply plug must comply with BS1363 (3-pin 13-amp)
and be fitted with a 5 A fuse which complies with
BS1362.
■ The mains cord must be <HAR> or <BASEC> marked and
be of type HO3VVF3GO.75 (minimum).
Europe
■ The supply plug must comply with CEE7/7 (“SCHUKO”)
■ The mains cord must be <HAR> or <BASEC> marked and
be of type HO3VVF3GO.75 (minimum).
L’INFORMATION DE SÉCURITÉ IMPORTANTE
Etats-Unis et
Canada:
■ Le cordon doit avoir reçu l’homologation des UL et un
certificat de la CSA.
■ Le cordon souple doit respecter, à titre minimum, les
spécifications suivantes:
calibre 18 AWG
type SV ou SJ
à 3 conducteurs
■ Le cordon doit être en mesure d’acheminer un courant
nominal d’au moins 10 A.
■ La prise femelle de branchement doit être du type à mise à la
terre (mise à la masse) et respecter la configuration NEMA
5-15P (15 A, 125 V) ou NEMA 6-15P (15 A, 250 V).
Danemark:
■ La prise mâle d’alimentation doit respecter la section 107-2 D1
de la norme DK2 1a ou DK2 5a.
Suisse:
■ La prise mâle d’alimentation doit respecter la norme SEV/ASE
1011.
Europe
■ La prise secteur doit être conforme aux normes CEE 7/7
(“SCHUKO”)
■ LE cordon secteur doit porter la mention <HAR> ou <BASEC>
et doit être de type HO3VVF3GO.75 (minimum).
WICHTIGE SICHERHEITSINFORMATIONEN
Stromkabel. Dies muss von dem Land, in dem es benutzt wird geprüft werden:
Schweiz
■ Dieser Stromstecker muß die SEV/ASE 1011Bestimmungen
einhalten.
Europe ■ Das Netzkabel muß vom Typ HO3VVF3GO.75
(Mindestanforderung) sein und die Aufschrift <HAR> oder
<BASEC> tragen.
■ Der Netzstecker muß die Norm CEE 7/7 erfüllen (”SCHUKO”).
4
Introduction
The Baseline 10/100 Switch is supplied with two mounting
brackets and four screws. These are used for rack-mounting the
unit. When mounting the unit, you should take note of the
guidelines given in “Positioning the Baseline 10/100 Switch” on
page 3.
Rack Mounting the Units
The Baseline 10/100 Switch is 1U high and will fit a standard
19-inch rack.
CAUTION: Disconnect all cables from the unit before
continuing. Remove the self-adhesive pads from the
underside of unit, if already fitted.
1 Place the unit the right way up on a hard, flat surface with
the front facing towards you.
2 Locate a mounting bracket over the mounting holes on one
side of the unit (refer to the figure following step 6).
3 Insert the two screws supplied in the mounting kit and fully
tighten with a suitable screwdriver.
4 Repeat the two previous steps for the other side of the unit.
5 Insert the unit into the 19-inch rack and secure with suitable
screws (not provided).
6 Reconnect all cables.
Refer to the information about LEDs given earlier in this guide to
see if the problem can be identified and rectified. Here are some
common problems that can occur:
Link Status LED not lit for a port that has a connection.
There is a problem with this connection. Check that:
The device being connected to is powered on and operating
correctly.
The cable is connected at both ends.
The cable is not damaged.
If the connection is to a workstation, that the workstation’s
network interface is installed and configured correctly.
All ports appear to show continual activity. There may be
broadcast storms on the network.
Remove port connections one at a time, waiting a few seconds
between each port. If the LEDs go off after removing a port
connection, the device that was connected to that port is
introducing an excessive amount of broadcast frames to the
network (some pieces of network equipment operate by sending
out broadcast frames regularly). Refer to the documentation that
accompanies the device for information on disabling the
broadcast operation.
If the problem persists and the unit still does not operate
successfully, contact your supplier with the following information
before returning the unit:
Product number and serial number (printed on a label
supplied with the unit)
A brief description of the fault
Related Standards
The SuperStack 3 Baseline 10/100 Switch has been designed to
the following standards:
Environmental
Physical
Electrical
MOUNTING KIT INSTRUCTIONS
PROBLEM SOLVING
TECHNICAL INFORMATION
Functional
ISO 8802-3, IEEE 802.3 (Ethernet), IEEE 802.3u (Fast
Ethernet), IEEE 802.3x (Flow Control), IEEE 802.3d
(Bridging)
Safety
UL 1950, EN 60950, CSA 22.2 #950, IEC 60950
EMC Emissions
EN 55022 Class A, FCC Part 15 Subpart B Class A,
ICES-003 Class A, VCCI Class A, AS/NZS 3548 Class A,
CNS 13438 Class A
Immunity
EN 55024
Operating Temperature
0–40 °C (32–104 °F)
Humidity
10–95% (non-condensing)
Width
440 mm (17.3 in.)
Depth
173 mm (6.8 in.)
Height
44 mm (1.7 in.) or 1U
Weight
2.6 kg (5.8 lb)
Mounting
Free standing, or 19 in. rack mounted using the
mounting kit supplied
Power Inlet
IEC 320
AC Line Frequency
50/60 Hz
Input Voltage
100–240 VAC
Current Rating
1 Amps (maximum)
Maximum Power
Consumption
3C16470: 15 VA
3C16471: 20 VA
Maximum Power
Dissipation
3C16470: 52 BTU/hr
3C16471: 68 BTU/hr
5
FCC Statement
This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to part 15 of the FCC
rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in
a commercial environment. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful
interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful
interference to radio communications, in which case the user will
be required to correct the interference at their own expense.
Information To The User
If this equipment does cause interference to radio or television
reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient the receiving antenna.
Relocate the equipment with respect to the receiver.
Move the equipment away from the receiver.
Plug the equipment into a different outlet so that equipment
and receiver are on different branch circuits.
If necessary, the user should consult the dealer or an experienced
radio/television technician for additional suggestions. The user
may find the following booklet prepared by the Federal
Communications Commission helpful:
How to Identify and Resolve Radio-TV Interference Problems
This booklet is available from the U.S. Government Printing
Office, Washington,
DC 20402, Stock No. 004-000-00345-4.
In order to meet FCC emissions limits, this equipment must be
used only with cables which comply with IEEE 802.3.
CE Statement (Europe)
This product complies with the European Low Voltage Directive
73/23/EEC and ETIC Directive 89/336/EEC as amended by
European Directive 93/68/EEC/.
CSA Statement
This Class A digital apparatus meets all requirements of the
Canadian Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe A respecte toutes les
exigences du Règlement sur le matériel brouilleur du Canada.
VCCI Statement
BSMI Statement
The following options are available for technical support:
In the first instance contact your Network Supplier.
Check the 3Com knowledgebase at
http://knowledgebase.3com.com
Browse the 3Com web site on http://www.3com.com
Please have your product model name, part number, hardware
revision number and serial number along with all relevant details
of the problem to hand before calling your Network Supplier or
3Com on the numbers below.
REGULATORY NOTICES
TECHNICAL SUPPORT
Country Telephone Number Country Telephone Number
Asia, Pacific Rim
Australia
Hong Kong
India
Indonesia
Japan
Malaysia
New Zealand
Pakistan
1 800 678 515
800 933 486
+61 2 9424 5179 or
000800 650 1111
001 803 61009
00531 616 439 or
03 5977 7991
1800 801 777
0800 446 398
+61 2 9937 5083
Philippines
P.R. of China
Singapore
S. Korea
Taiwan
Thailand
1235 61 266 2602 or
+61 2 9937 5076
10800 61 00137 or
021 6350 1590 or
00800 0638 3266
800 6161 463
00798 611 2230 or
02 3455 6455
0080 611 261
001 800 611 2000
Europe, Middle East and Africa
From anywhere in these regions, call: +44 (0)1442 435529 phone
+44 (0)1442 432524 fax
6
© 3Com Technologies, 2002. All rights reserved. No part of this documentation
may be reproduced in any form or by any means or used to make any derivative
work (such as translation, transformation, or adaptation) without permission from
3Com Technologies.
3Com Technologies reserves the right to revise this documentation and to make
changes in content from time to time without obligation on the part of 3Com
Technologies to provide notification of such revision or change.
3Com Technologies provides this documentation without warranty of any kind,
either implied or expressed, including, but not limited to, the implied warranties of
merchantability and fitness for a particular purpose. 3Com may make improvements
or changes in the product(s) and/or the program(s) described in this documentation
at any time.
UNITED STATES GOVERNMENT LEGENDS:
If you are a United States government agency, then this documentation and the
software described herein are provided to you subject to the following restricted
rights:
For units of the Department of Defense:
Restricted Rights Legend: Use, duplication or disclosure by the Government is
subject to restrictions as set forth in subparagraph (c) (1) (ii) for restricted Rights in
Technical Data and Computer Software clause at 48 C.F.R. 52.227-7013. 3Com
Centre, Boundary Way, Maylands Park South, Hemel Hempstead, Herts, HP2 7YU,
U.K.
For civilian agencies:
Restricted Rights Legend: Use, reproduction or disclosure is subject to restrictions set
forth in subparagraph (a) through (d) of the Commercial Computer Software -
Restricted Rights Clause at 48 C.F.R. 52.227-19 and the limitations set forth in
3Com Corporation’s standard commercial agreement for the software. Unpublished
rights reserved under the copyright laws of the United States.
If there is any software on removable media described in this documentation, it is
furnished under a license agreement included with the product as a separate
document, in the hard copy documentation, or on the removable media in a
directory file named LICENSE.TXT. If you are unable to locate a copy, please contact
3Com and a copy will be provided to you.
Unless otherwise indicated, 3Com registered trademarks are registered in the United
States and may or may not be registered in other countries.
3Com and SuperStack are registered trademarks of 3Com Corporation.
Other brand and product names may be registered trademarks or trademarks of their
respective holders.
General Environmental Statement
It is the policy of 3Com Corporation to be environmentally-friendly in all
operations. To uphold our policy, we are committed to:
Establishing environmental performance standards that comply
with national legislation and regulations
Conserving energy, materials and natural resources in all
operations
Reducing the waste generated by all operations
Ensuring that all waste conforms to recognized environmental
standards
Maximizing the recyclable and reusable content of all products
Ensuring that all products can be recycled, reused and disposed
of safely
Ensuring that all products are labelled according to recognized
environmental standards
Improving our environmental record on a continual basis
End Of Life Statement
3Com processes allow for the recovery, reclamation and safe disposal of
all end-of-life electronic components.
Regulated Materials Statement
3Com products do not contain any hazardous or ozone-depleting
material.
Enviromental Statement about the Documentation
The documentation for this product is printed on paper that comes from
sustainable, managed forests; it is fully biodegradeable and recyclable,
and is completely chlorine-free. The varnish is enviromentally-friendly, and
the inks are vegetable-based with a low heavy-metal content.
From the following countries, you may use the toll-free numbers:
Austria
Belgium
Denmark
Finland
France
Germany
Hungary
Ireland
Israel
Italy
0800 297468
0800 71429
800 17309
0800 113153
0800 917959
0800 1821502
06800 12813
1800 553117
1800 9453794
800 879489
Luxembourg
Netherlands
Norway
Poland
Portugal
South Africa
Spain
Sweden
Switzerland
U.K.
0800 3625
0800 0227788
800 11376
00800 3111206
800 831416
0800 995014
900 983125
020 795482
0800 55 3072
0800 966197
Latin America
From the Caribbean, Central and South America, call:
Antigua
Argentina
Aruba
Bahamas
Barbados
Belize
Bermuda
Bonaire
Brazil
Cayman
Chile
Colombia
Costa Rica
Curacao
Ecuador
Dominican Republic
1 800 988 2112
0 810 444 3COM
1 800 998 2112
1 800 998 2112
1 800 998 2112
52 5 201 0010
1 800 998 2112
1 800 998 2112
0800 13 3COM
1 800 998 2112
AT&T +800 998 2112
AT&T +800 998 2112
AT&T +800 998 2112
1 800 998 2112
AT&T +800 998 2112
AT&T +800 998 2112
Guatemala
Haiti
Honduras
Jamiaca
Martinique
Mexico
Nicaragua
Panama
Paraguay
Peru
Puerto Rico
Salvador
Trinidad and Tobago
Uruguay
Venezuela
Virgin Islands
AT&T +800 998 2112
57 1 657 0888
AT&T +800 998 2112
1 800 998 2112
571 657 0888
01 800 849CARE
AT&T +800 998 2112
AT&T +800 998 2112
54 11 4894 1888
AT&T +800 998 2112
1 800 998 2112
AT&T +800 998 2112
1 800 998 2112
AT&T +800 998 2112
AT&T +800 998 2112
57 1 657 0888
North America 1 800 876 3266
Country Telephone Number Country Telephone Number
LEGAL NOTICES
ENVIROMENTAL STATEMENTS
7
Part Number: DUA1647-0AAA01
Published: May 2002
Product Registration
You can now register your SuperStack 3 Baseline 10/100 Switch on the 3Com web site:
http://support.3com.com/registration/frontpg.pl
Documentation Feedback
Your suggestions are very important to us. They will help make our documentation more useful to you. Please e-mail comments about
this document to 3Com at:
Please include the following information when commenting: the document title, part number (shown at the bottom of this page), and
page number, if appropriate.
8
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
3com SuperStack 3 3C16410 Manuel utilisateur
- Catégorie
- Commutateurs réseau
- Taper
- Manuel utilisateur
- Ce manuel convient également à
dans d''autres langues
Documents connexes
-
3com SuperStack 3 3C16475 Manuel utilisateur
-
-
-
-
-
-
-
HP SS3 BASELINE 10 / 100 SWTCH 24 PT Le manuel du propriétaire
-
3com SuperStack II 3C16592A Manuel utilisateur
-