Wacker Neuson LTW8K Manuel utilisateur

Operator’s Manual

Light Tower, Wide Body

LTW 6K

LTW 8K

Notice d’Emploi

Tour d’éclairage, corps large

5000187665 04 0712

5000187665

EN / FR

Copyright

notice

All rights, including copying and distribution rights, are reserved.

This publication may be photocopied by the original purchaser of the machine. Any

other type of reproduction is prohibited without express written permission from

Wacker Neuson Production Americas LLC.

Any type of reproduction or distribution not authorized by Wacker Neuson Production

Americas LLC represents an infringement of valid copyrights. Violators will be

prosecuted.

Trademarks

All trademarks referenced in this manual are the property of their respective owners.

Manufacturer

Wacker Neuson Production Americas LLC

N92W15000 Anthony Avenue

Menomonee Falls, WI 53051 U.S.A.

Tel: (262) 255-0500 · Fax: (262) 255-0550 · Tel: (800) 770-0957

www.wackerneuson.com

Original

instructions

This Operator’s Manual presents the original instructions. The original language of this

Operator’s Manual is American English.

5000187641 03 1111

LTW 6K / 8K Foreword

wc_tx001053gb.fm 3

Foreword

SAVE THESE INSTRUCTIONS—This manual contains important instructions for

the machine models below. These instructions have been written expressly by

Wacker Neuson Production Americas LLC and must be followed during installation,

operation, and maintenance of the machines.

Machines

covered by

this manual

;

Machine

documentation

 From this point forward in this documentation, Wacker Neuson Production

Americas LLC will be referred to as Wacker Neuson.

 Keep a copy of the Operator’s Manual with the machine at all times.

 Use the separate Parts Book supplied with the machine to order replacement

parts.

 Refer to the separate Repair Manual for detailed instructions on servicing and

repairing the machine.

 If you are missing any of these documents, please contact Wacker Neuson to

order a replacement or visit www.wackerneuson.com.

 When ordering parts or requesting service information, be prepared to provide

the machine model number, item number, revision number, and serial number.

Expectations

for

information in

this manual

 This manual provides information and procedures to safely operate and

maintain the above Wacker Neuson model(s). For your own safety and to

reduce the risk of injury, carefully read, understand, and observe all instructions

described in this manual.

 Wacker Neuson expressly reserves the right to make technical modifications,

even without notice, which improve the performance or safety standards of its

machines.

 The information contained in this manual is based on machines manufactured

up until the time of publication. Wacker Neuson reserves the right to change

any portion of this information without notice.

CALIFORNIA

Proposition

65 Warning

Engine exhaust, some of its constituents, and certain vehicle components, contain

or emit chemicals known to the State of California to cause cancer and birth

defects or other reproductive harm.

Laws

pertaining to

spark

arresters

NOTICE: State Health Safety Codes and Public Resources Codes specify that in

certain locations spark arresters be used on internal combustion engines that use

hydrocarbon fuels. A spark arrester is a device designed to prevent accidental dis-

charge of sparks or flames from the engine exhaust. Spark arresters are qualified

and rated by the United States Forest Service for this purpose. In order to comply

with local laws regarding spark arresters, consult the engine distributor or the local

Health and Safety Administrator.

Manufacturer’s

approval

This manual contains references to approved parts, attachments, and modifica-

tions. The following definitions apply:

Machine Item Number

LTW 6K 0620372, 0620840, 0621241, 5200004094

LTW 8K 0620374, 0620841, 0621242, 520004095, 5200004204

Foreword LTW 6K / 8K

4 wc_tx001053gb.fm

 Approved parts or attachments are those either manufactured or provided by

Wacker Neuson.

 Approved modifications are those performed by an authorized Wacker

Neuson service center according to written instructions published by Wacker

Neuson.

 Unapproved parts, attachments, and modifications are those that do not

meet the approved criteria.

Unapproved parts, attachments, or modifications may have the following conse-

quences:

 Serious injury hazards to the operator and persons in the work area

 Permanent damage to the machine which will not be covered under warranty

Contact your Wacker Neuson dealer immediately if you have questions about

approved or unapproved parts, attachments, or modifications.

LTW 6K / 8K Table of Contents

wc_bo5000187641_03TOC.fm 5

Foreword 3

1 Safety Information 7

1.1 Signal Words Found in this Manual ...................................................... 7

1.2 Machine Description and Intended Use ............................................... 7

1.3 Safety Guidelines for Operating the Machine ....................................... 9

1.4 Operator Safety while Using Internal Combustion Engines ............... 12

1.5 Towing Safety ..................................................................................... 13

1.6 Service Safety .................................................................................... 14

2 Labels 16

2.1 Label Locations .................................................................................. 16

2.2 Label Meanings .................................................................................. 18

3 Operation 30

3.1 Preparing the Machine for First Use ................................................... 30

3.2 Preparing Trailer for Towing or Lifting ................................................ 31

3.3 Locating the Trailer ............................................................................. 32

3.4 Ground Connection ............................................................................ 32

3.5 Leveling Trailer ................................................................................... 33

3.6 Refueling the Machine ........................................................................ 34

3.7 Adjusting the Lights ............................................................................ 35

3.8 Control Panel (Manual Winch) ........................................................... 36

3.9 Raising the Tower (Manual Winch) .................................................... 37

3.10 Lowering the Tower (Manual Winch) .................................................. 40

3.11 Control Panel (Power Winch) ............................................................. 42

3.12 Raising the Tower (Power Winch) ...................................................... 43

3.13 Lowering the Tower (Power Winch) .................................................. 46

3.14 Manually Starting the Machine ........................................................... 48

3.15 Stopping the Machine ......................................................................... 49

3.16 Auto Mode (Remote Run) .................................................................. 49

3.17 Troubleshooting Automatic Shutdown ................................................ 50

3.18 Generator Derating ............................................................................. 51

3.19 Receptacle Panel ............................................................................... 52

3.20 Emergency Stop Switch ..................................................................... 53

Table of Contents LTW 6K / 8K

6 wc_bo5000187641_03TOC.fm

4 Maintenance 54

4.1 Periodic Maintenance Schedule ..........................................................54

4.2 Installing / Removing Light Fixtures ....................................................56

4.3 Replacing / Removing Lamps .............................................................57

4.4 Performing Daily Inspection ................................................................58

4.5 Checking Engine Coolant ....................................................................58

4.6 Cleaning Air Filter Element ..................................................................59

4.7 Changing Engine Oil ...........................................................................60

4.8 Maintaining the Fuel/Water Separator .................................................61

4.9 Maintaining the Trailer .........................................................................61

4.10 Long-Term Storage .............................................................................62

4.11 Troubleshooting ...................................................................................63

5 Factory-Installed Options 64

5.1 General Options ..................................................................................64

5.2 Cold Weather Options .........................................................................69

5.3 North Slope Options ............................................................................69

6 Technical Data 72

6.1 Engine .................................................................................................72

6.2 Generator ............................................................................................73

6.3 Machine ...............................................................................................73

6.4 Dimensions ..........................................................................................74

7 Schematics 76

7.1 LTW 6K—Electrical Schematic ...........................................................76

7.2 LTW 6K—Electrical Schematic Components ......................................77

7.3 LTW 8K—Electrical Schematic ...........................................................78

7.4 LTW 8K—Electrical Schematic Components ......................................79

7.5 Engine Wiring ......................................................................................80

7.6 Engine Wiring Components .................................................................81

7.7 Trailer Wiring (Electric Brakes) ............................................................82

7.8 Trailer Wiring Components (Electric Brakes) ......................................82

7.9 Trailer Wiring (Surge Brakes / No Brakes) ..........................................83

LTW 6K/8K Safety Information

wc_si000299gb.fm 7

1 Safety Information

1.1 Signal Words Found in this Manual

This manual contains DANGER, WARNING, CAUTION, NOTICE, and NOTE

signal words which must be followed to reduce the possibility of personal injury,

damage to the equipment, or improper service.

NOTICE: Used without the safety alert symbol, NOTICE indicates a situation

which, if not avoided, could result in property damage.

Note: A Note contains additional information important to a procedure.

1.2 Machine Description and Intended Use

This machine is a mobile, trailer-mounted light tower. The Wacker Neuson Light

Tower consists of a trailer with a cabinet containing a diesel engine, a fuel tank, a

control panel, and an electric alternator. A telescoping tower with four metal halide

lights is mounted to the top of the cabinet. Dual winches tilt, raise, and lower the

telescoping tower. As the engine runs, the generator converts mechanical energy

into electric power. The metal halide lights run off this power. Receptacle(s) are

also present to power auxiliary loads. The operator uses the control panel to

operate and monitor the machine.

This is the safety alert symbol. It is used to alert you to potential personal hazards.

f Obey all safety messages that follow this symbol.

DANGER

DANGER indicates a hazardous situation which, if not avoided, will result in death

or serious injury.

f

To avoid death or serious injury from this type of hazard, obey all safety messages that

follow this signal word.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could result in

death or serious injury.

f

To avoid possible death or serious injury from this type of hazard, obey all safety mes-

sages that follow this signal word.

CAUTION!

CAUTION indicates a hazardous situation which, if not avoided, could result in

minor or moderate injury.

f

To avoid possible minor or moderate injury from this type of hazard, obey all safety mes-

sages that follow this signal word.

Safety Information LTW 6K/8K

8 wc_si000299gb.fm

This machine is intended for the illumination of outdoor areas. This machine is also

intended for the purpose of supplying electrical power to connected loads. Refer to

the product specifications for the output voltage and frequency of this Light Tower,

and for the maximum output power limit of this Light Tower.

This machine has been designed and built strictly for the intended use described

above. Using the machine for any other purpose could permanently damage the

machine or seriously injure the operator or other persons in the area. Machine

damage caused by misuse is not covered under warranty.

 The following are some examples of misuse:

 Connecting a load that has voltage and frequency requirements that are

incompatible with the machine output

 Overloading the machine with a device that draws excessive power during

either continuous running or start-up

 Operating the machine in a manner that is inconsistent with all federal, state and

local codes and regulations

 Using the machine as a ladder, support, or work surface

 Using the machine to carry or transport passengers or equipment

 Using the machine to tow other machines (unless factory equipped)

 Using the machine as a hoist or hanging items from the tower

 Operating the machine outside of factory specifications

 Operating the machine in a manner inconsistent with all warnings found on the

machine and in the Operator’s Manual

This machine has been designed and built in accordance with the latest global

safety standards. It has been carefully engineered to eliminate hazards as far as

practicable and to increase operator safety through protective guards and labeling.

However, some risks may remain even after protective measures have been taken.

They are called residual risks. On this machine, they may include exposure to:

 Heat, noise, exhaust, and carbon monoxide from the engine

 Heat from the lights

 Ultraviolet radiation from the lights

 Fire hazards from improper refueling techniques

 Fuel and its fumes

 Electric shock and arc flash

 Personal injury from improper lifting the trailer tongue

 Glare from lights (lights may blind drivers of nearby motor vehicles if the lights

are incorrectly positioned)

 Typical hazards related to towing a trailer on roads and highways

To protect yourself and others, make sure you thoroughly read and understand the

safety information presented in this manual before operating the machine.

LTW 6K/8K Safety Information

wc_si000299gb.fm 9

1.3 Safety Guidelines for Operating the Machine

Operator

qualifications

Only trained personnel are permitted to start, operate, and shut down the machine.

They also must meet the following qualifications:

 have received instruction on how to properly use the machine

 are familiar with required safety devices

The machine must not be accessed or operated by:

 children

 people impaired by alcohol or drugs

Personal

Protective

Equipment

(PPE)

Wear the following Personal Protective Equipment (PPE) while operating this

machine:

 Close-fitting work clothes that do not hinder movement

 Safety glasses with side shields

 Hearing protection

 Safety-toed footwear

Work area

 Make sure the area immediately surrounding the Light Tower is clean, neat, and

free of debris.

 The tower extends up to 9 m (30 ft). Make sure the area above the trailer is

open and clear of overhead wires and obstructions.

Machine

setup

 Make sure the machine is on a firm, level surface and will not tip, roll, slide, or

fall while operating.

 Make sure the machine is well-grounded and securely fastened to a good

earthen ground per national and local regulations.

 The trailer must be leveled and the outriggers extended before raising the tower.

The outriggers must be extended while the tower is up.

 Never connect the machine to other power sources, such as supply mains of

power companies.

Machine

integrity

 Do not start a machine in need of repair.

 Do not use the machine if the insulation on any electrical cord is cut or worn

through.

 Do not operate the lights without the protective lens cover in place or with a lens

cover that is cracked or damaged.

 Replace or repair electrical components with components that are identical in

rating and performance to the originals.

While

operating the

machine

 Keep the area behind the trailer clear of people and obstructions while raising

and lowering the tower.

 Do not raise the tower or operate the machine in high winds. Lower the tower

immediately if high winds or electrical storms are expected in the area.

 Do not raise, lower, or turn the tower while the unit is operating.

 If any part of the tower hangs up, or the winch cable develops slack while raising

or lowering the tower, STOP immediately! Contact an authorized Wacker

Neuson service representative.

 Do not disengage the tower locking pin while the tower is up.

Safety Information LTW 6K/8K

10 wc_si000299gb.fm

 Lamps become extremely hot in use! Allow the lamps and fixtures to cool 10–15

minutes before handling.

 Lower the tower when not in use.

Work area

 Make sure the area immediately surrounding the Light Tower is clean, neat, and

free of debris.

 The tower extends up to 9 m (30 ft). Make sure the area above the trailer is

open and clear of overhead wires and obstructions.

Machine

setup

 Make sure the machine is on a firm, level surface and will not tip, roll, slide, or

fall while operating.

 Make sure the machine is well-grounded and securely fastened to a good

earthen ground per national and local regulations.

 The trailer must be leveled and the outriggers extended before raising the tower.

The outriggers must be extended while the tower is up.

 Never connect the machine to other power sources, such as supply mains of

power companies.

Machine

integrity

 Do not start a machine in need of repair.

 Do not use the machine if the insulation on any electrical cord is cut or worn

through.

 Do not operate the lights without the protective lens cover in place or with a lens

cover that is cracked or damaged.

 Replace or repair electrical components with components that are identical in

rating and performance to the originals.

While

operating the

machine

 Keep the area behind the trailer clear of people and obstructions while raising

and lowering the tower.

 Do not raise the tower or operate the machine in high winds. Lower the tower

immediately if high winds or electrical storms are expected in the area.

 Do not raise, lower, or turn the tower while the unit is operating.

 If any part of the tower hangs up, or the winch cable develops slack while raising

or lowering the tower, STOP immediately! Contact an authorized Wacker

Neuson service representative.

 Do not disengage the tower locking pin while the tower is up.

 Lamps become extremely hot in use! Allow the lamps and fixtures to cool 10–15

minutes before handling.

 Lower the tower when not in use.

Lamp Safety

Description

The lamps provided with your Light Tower are electric discharge lamps. They are

designed for use with metal halide ballasts only, and require time to reach full

brightness on initial startup and after a power interruption. These lamps comply

with FDA regulation performance standards 21 CFR 1040-30.

LTW 6K/8K Safety Information

wc_si000299gb.fm 11

Operating

safety

 Do not operate the lamps where people will remain for more than a few minutes

unless adequate shielding or other safety precautions are used.

 Replace damaged lamps according to the instructions in section Removing /

Replacing Lamps.

 Lamps that automatically extinguish when the outer envelope is broken or

punctured are commercially available.

WARNING

Personal injury hazard. Lamps can cause serious skin burns and eye inflammation

from shortwave ultraviolet radiation if outer envelope of the lamp is broken or punc-

tured.

f Do not operate the Light Tower if a lamp is damaged.

Safety Information LTW 6K/8K

12 wc_si000299gb.fm

1.4 Operator Safety while Using Internal Combustion Engines

Operating

safety

When running the engine:

 Keep the area around exhaust pipe free of flammable materials.



Check the fuel lines and the fuel tank for leaks and cracks before starting the engine.

Do not run the machine if fuel leaks are present or the fuel lines are loose.

When running the engine:

 Do not smoke while operating the machine.

 Do not run the engine near sparks or open flames.

 Do not touch the engine or muffler while the engine is running or immediately

after it has been turned off.

 Do not operate a machine when its fuel cap is loose or missing.

 Do not start the engine if fuel has spilled or a fuel odor is present. Move the

machine away from the spill and wipe the machine dry before starting.

Refueling

safety

When refueling the engine:

 Clean up any spilled fuel immediately.

 Refill the fuel tank in a well-ventilated area.

 Replace the fuel tank cap after refueling.

 Do not smoke.

 Do not refuel a hot or running engine.

 Do not refuel the engine near sparks or open flames.

WARNING

Internal combustion engines present special hazards during operation and fueling. Failure to

follow the warnings and safety standards could result in severe injury or death.

f Read and follow the warning instructions in the engine owner’s manual and the

safety guidelines below.

DANGER

Exhaust gas from the engine contains carbon monoxide, a deadly poison. Expo-

sure to carbon monoxide can kill you in minutes.

f NEVER operate the machine inside an enclosed area, such as a tunnel, unless

adequate ventilation is provided through such items as exhaust fans or hoses.

LTW 6K/8K Safety Information

wc_si000299gb.fm 13

1.5 Towing Safety

Read and follow the information below:

Equipment

integrity

 Both the trailer and vehicle must be in serviceable condition and securely

fastened together.

 Ensure that the hitch and coupling on the towing vehicle are rated equal to, or

greater than, the trailer’s Gross Vehicle Weight Rating (GVWR).

 Inspect the hitch and coupling for wear or damage. Do not tow the trailer using

defective parts.

 Always connect the safety chains.

 Make sure all directional and trailer lights are connected and working properly.

 Check the tires on the trailer for tread wear, inflation, and condition. Replace

worn tires.

 Verify that all lug nuts holding the wheels are tight and none are missing.

Checking

brakes

 On trailers with surge or electric brakes, connect the breakaway cable (a) on the

trailer coupler to the rear bumper or frame of the vehicle. This cable will actuate

the brake system on the trailer if both the coupling and safety chains have

failed. The breakaway cable is not a parking brake and should not be used as

one.

 Check the operation of the brakes by braking the vehicle at a slow speed before

entering traffic. Both the vehicle and the trailer should brake smoothly. If the

trailer seems to be pushing, check the fluid level (b) in the surge brakes or the

operation of the electric brakes.

Towing speed

 The maximum recommended speed for highway towing is 88 km/hour (55 mph).

Recommended off-road towing speed is not to exceed 16 km/hour (10 mph) or

less depending on terrain.

WARNING

Possibility of personal injury or equipment damage. Towing a large trailer can be

hazardous without careful preparation, appropriate equipment, and/or observance

of maximum towing speeds.

f Refer to the applicable Department of Transportation regulations before towing.

wc_gr006973

a

b

Safety Information LTW 6K/8K

14 wc_si000299gb.fm

1.6 Service Safety

Precautions

 To reduce the risk of personal injury, read and understand the service

procedures before performing any service to the machine.

 All adjustments and repairs MUST be completed before operation. Do not

operate the machine with a known problem or deficiency! All repairs and

adjustments should be completed by a qualified technician.

 Do not service the machine if your clothing or skin is wet.

Personal

Protective

Equipment

(PPE)

Wear the following Personal Protective Equipment (PPE) while servicing or

maintaining this machine:

 Close-fitting work clothes that do not hinder movement

 Safety glasses with side shields

 Hearing protection

 Safety-toed footwear

In addition, before servicing or maintaining the machine:

 Tie back long hair.

 Remove all jewelry (including rings).

Before

servicing the

machine

 Turn the engine off before performing maintenance or making repairs.

 Make sure the engine start switch is turned to OFF.

 Make sure the circuit breakers are open (off).

 Make sure the negative terminal on the battery is disconnected.

 Do not perform even routine service (oil / oil filter changes, cleaning, etc.) unless

all electrical components are shut down.

 Make sure water has not accumulated around the base of the machine. If water

is present, move the machine and allow it to dry before servicing.

 If the machine must be started while servicing, keep hands, feet, and loose

clothing away from moving parts on the generator and engine.

Safety

devices and

modifications

 Replace all safety devices and guards after repair and maintenance.

 Do not modify the machine without the express written approval of the

manufacturer.

Replacing

parts and

labels

 Replace worn or damaged components.

 Use only spare parts recommended by Wacker Neuson.

 Replace all missing and hard-to-read labels.

 Check all external fasteners at regular intervals.

WARNING

High voltage! This machine produces high voltage capable of causing serious injury

or death.

f Only a qualified electrician should troubleshoot or repair electrical problems

occurring with this machine.

LTW 6K/8K Safety Information

wc_si000299gb.fm 15

Lifting and

transporting

When lifting the machine:

 Make sure slings, chains, hooks, ramps, jacks and other types of lifting devices

are attached securely and have enough weight-bearing capacity to lift or hold

the machine safely.

 Remain aware of the location of other people when lifting the machine.

To reduce the possibility of injury:

 Do not stand under the machine while it is being hoisted or moved.

 Do not get onto the machine while it is being hoisted or moved.

Labels LTW 6K / 8K

16 wc_si000385gb.fm

2 Labels

2.1 Label Locations

wc_gr006242

12

BB

OO

DDRR

DD

K

BB

DD

F

CC

L

V

LL

NN

SS

LL

W

FF

D

FF

DD

B

Y

LTW 6K / 8K Labels

wc_si000385gb.fm 17

wc_gr006243

BB

Q

R

O

B

DD

GG

J

C

N

FF

D

IG

FF

E

U

V

S

A

H

HH

T

J

MM

PP

SS

JJ

T

AA

QQ

NN

KK

TT

M

Labels LTW 6K / 8K

18 wc_si000385gb.fm

2.2 Label Meanings

Wacker Neuson machines use international pictorial labels where

needed. These labels are described below.

A

WARNING

Automatic locking pin.

A non-secured, falling tower can cause serious

injury or death if a person is hit. To secure tower,

verify automatic locking pin has been engaged.

B

WARNING!

Avoid crushing area.

C

DANGER!

Contact with overhead electrical power lines will

cause serious injury or death. Do not position

Light Tower under electrical power lines.

WARNING!

Completely lower tower BEFORE tilting tower.

Tilting an extended tower can cause serious

injury or death.

LTW 6K / 8K Labels

wc_si000385gb.fm 19

D

NOTICE

Lifting point.

E

WARNING!

Secure tower in transport lock before lifting or

towing. A loose swinging tower could cause per-

sonal injury or machine damage.

F

DANGER

Using a light tower indoors CAN KILL YOU IN

MINUTES. Light tower exhaust contains carbon

monoxide. This is a poison you cannot see or

smell.

NEVER use inside a home or garage, EVEN IF

doors and windows are open.

Only use OUTSIDE and far away from windows,

doors, and vents.

G

DANGER!

Asphyxiation hazard.

 Engines emit carbon monoxide.

 Do not run the machine indoors or in an

enclosed area unless adequate ventilation,

through such items as exhaust fans or hoses,

is provided.

 Read the Operator’s Manual. No sparks,

flames, or burning objects near the machine.

Stop the engine before refueling.

Labels LTW 6K / 8K

20 wc_si000385gb.fm

H

WARNING!

Electric shock and arc flash can cause serious

injury or death. Electrical storage device within.

Contact a qualified electrician for service or to

open electrical box.

I

WARNING!

Read and understand the supplied Operator’s

Manual before operating the machine. Failure to

do so increases the risk of injury to yourself and

others.

La page charge ...

Wacker Neuson LTW8K Manuel utilisateur

Ce manuel convient également à

Wacker Neuson LTW8K Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents