Amana 5GBR22PRAA Mode d'emploi

2

Important Safety Instructions

To reduce risk of fire, electric shock, serious injury

or death when using your refrigerator, follow these

basic precautions, including the following:

1. Read all instructions before using the refrigerator.

2. Observe all local codes and ordinances.

3. Be sure to follow earthing instructions.

4. Check with a qualified electrician if you are not sure

this appliance is properly earthed.

5. Do not earth to a gas line.

6. Do not earth to a cold-water pipe.

7. Refrigerator is designed to operate on a separate

220-240 volt, 10 amp., 50 HZ cycle line.

8. Do not modify plug on power cord. If plug does not

fit electrical outlet, have proper outlet installed by a

qualified electrician.

9. Do not use a two-prong adapter, extension cord or

power strip.

10. Do not tamper with refrigerator controls.

11. Do not service or replace any part of refrigerator

unless specifically recommended in Use & Care

Guide or published user-repair instructions. Do not

attempt service if instructions are not understood or

if they are beyond personal skill level.

12. Always disconnect refrigerator from electrical supply

before attempting any service. Disconnect power

cord by grasping the plug, not the cord.

13. Install refrigerator according to Installation

Instructions. All connections for water, electrical

power and earthing must comply with local codes

and be made by licensed personnel when required.

14. Keep your refrigerator in good condition. Bumping

or dropping refrigerator can damage refrigerator or

cause refrigerator to malfunction or leak. If damage

occurs, have refrigerator checked by qualified

service technician.

15. A qualified service technician must replace worn

power cords and/or loose plugs.

16. Always read and follow manufacturer’s storage and

ideal environment instructions for items being stored

in refrigerator.

17. Your refrigerator should not be operated in the

presence of explosive fumes.

18. Children should not climb, hang or stand on any

part of the refrigerator.

19. Clean up spills or water leakage associated with

water installation.

20. The appliance is not intended for use by young

children or infirm persons without supervision.

21. Young children should be supervised to ensure that

they do not play with the appliance.

WARNING

SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE

Installing Your Refrigerator

These instructions were provided to aid you in the installation of your unit. The manufacturer cannot be responsible

for improper installation.

Steps to Follow...

A qualified engineer must connect refrigerator in accordance with these installation instructions.

Measure door opening and depth and width of refrigerator. Remove handles or doors if required. Engineer must

also do the following:

1. Follow local water and electrical company connection regulations.

2. Complete water supply connection before electrical supply connections.

Service to or replacement of power cord must be performed by a qualified engineer.

Note:

When writing or calling about a service problem, please include the following information:

a. Your name, address and telephone number; d. A clear description of the problem you are having;

b. Model number and serial number; e. Proof of purchase (sales receipt)

c. Name and address of your dealer or engineer;

3

Installation

Your refrigerator was packed carefully for shipment.

Remove and discard shelf packaging and tape. Do not

remove the serial plate.

Measuring the Opening

When installing your refrigerator, measure carefully. 1.3

cm (

1

⁄2”) of air space should be provided for the top and

back of the refrigerator.

Subflooring or floor coverings (i.e. carpet, tile, wood

floors, rugs) may make your opening smaller than

anticipated.

Some clearance may be gained by using the leveling

procedure under Leveling.

Important: If refrigerator is to be installed into a

recess where the top of the refrigerator is completely

covered, use dimensions from floor to top of hinge cap

to verify proper clearance.

Transporting Your Refrigerator

• NEVER transport refrigerator on its side. If an

upright position is not possible, lay refrigerator on its

back. Allow refrigerator to sit upright for

approximately 30 minutes before plugging it in to

assure oil returns to the compressor. Plugging the

refrigerator in immediately may cause damage to

internal parts.

• Use an appliance dolly when moving refrigerator.

ALWAYS truck refrigerator from its side or

back–NEVER from its front.

• Protect outside finish of refrigerator during transport

by wrapping cabinet in blankets or inserting padding

between the refrigerator and dolly.

• Secure refrigerator to dolly firmly with straps or

bungee cords. Thread straps through handles when

possible. Do not over-tighten. Over-tightening

restraints may dent or damage outside finish.

Leveling

To protect property and refrigerator from

damage, observe the following:

• Protect vinyl or other flooring with cardboard, rugs,

or other protective material.

• Do not use power tools when performing leveling

procedure.

CAUTION

To enhance the appearance and maintain performance,

the refrigerator should be level. (side to side)

Materials Needed:

•

3

⁄8” hex head driver

• Carpenter’s level

1. Remove toe grille.

• Grasp firmly and pull

outward to unclip.

To be done by a qualified engineer only.

WARNING

Contact a qualified engineer to perform this task.

WARNING

How to Remove and Replace

Door and Hinges

Contact a qualified engineer to perform this task.

WARNING

How to Connect the Water

Supply (select models)

60 cm deep models

Note: Trim corners of countertop to a 45° angle if

countertop has 25 mm overhang. Provide 5 mm

clearance on both sides of refrigerator, and allow

7 mm on top for ease of installation and leveling.

No minimum clearance is required at the rear of the

cabinet.

Location

• Do not install refrigerator near oven, radiator or

other heat source. If not possible, shield refrigerator

with cabinet material.

• Do not install where temperature falls below 13° C

or rises above 95° C. Malfunction may occur at this

temperature.

• Refrigerator is designed for indoor household

application only.

Notes:

• Complete any required water supply connection

before leveling.

• Some models only have adjustment screws (A).

For pullout drawer only:

1. Turn both stabilizing

legs clockwise until

firmly against floor.

Turn roller

adjustment screws 2

to 3 times counterclockwise so that the full

weight of refrigerator rests on stabilizing legs.

2. Replace toe grille. See markings on inside of toe

grille to insure proper placement.

Roller Adjustment Screw

Stabilizing

Leg

4

Installation

CC

A

B

A

B

4. Using the carpenter’s level, make sure front of

refrigerator is 6 mm or approximately one half

bubble higher than back of refrigerator and that

the refrigerator is level from side to side.

5. Turn stabilizing legs (C) clockwise until firmly

against floor.

6. Freezer drawer models only: Turn adjustment

screws (A) counterclockwise to allow the full

weight of the refrigerator to rest on the

stabilizing legs.

7. Replace the toe grille.

• Align the toe grille mounting clips with the lower

cabinet slots.

• Snap bottom portion into place first. Press

down on top of grille until top portion snaps into

place.

2. Using hex head driver, turn the front adjustment

screws (A) on each side to raise or lower the front

of the refrigerator.

Handles

If not installed, the handle is located in the interior of

the fresh food section or attached to the back of your

refrigerator.

Remove and discard handle packaging and tape.

Handle design varies from refrigerator to refrigerator.

Please reference the appropriate instructions for your

model below.

3. Select models also have rear adjustment screws

(B). Using the hex head driver, turn each of these

adjustment screws (B) to raise or lower the rear of

the refrigerator.

Fresh Food Handles

Front Mount Handle - Style 1

Materials Needed:

• Phillips screwdriver

•

5

⁄16” hex head driver

To Install:

1. Remove 0.6 cm hex head screws from

door face with hex head driver, and

Phillips screw from top of door.

• If reversing door, remove door plugs

from opposite side of door and

insert in screw holes.

2. Align handle holes with screw holes on

door face and secure with two door face

screws from step 1.

3. Locate handle trim in literature pack and

install over top and bottom of handle, as

illustrated.

• Secure top handle trim with remaining

screw removed in step 1.

• Snap bottom trim over bottom portion

of handle.

To Remove:

1. Remove top handle trim by removing top

handle screw.

• Retain trim and screw for later

replacement.

2. Pry bottom handle trim from handle with

screwdriver flat blade wrapped in

masking tape.

• Retain trim for later replacement.

3. Remove two hex head screws.

• Retain screws for later replacement.

Side Mount Handle

Materials Needed:

• Phillips screwdriver

To Install:

1. Remove screws from the side of the door.

2. Align the side mount handle with the pre-drilled

holes in the door panel.

5

Installation

3. Insert the screws in the sequence as

shown.

4. Ensure the door handle is snug to the

door panel.

To Remove:

Reverse installation procedure.

Upper

Handle

Lower

Handle

1

3

2

4

Freezer Handles

Partial-Width Handle

Materials Needed:

• Phillips screwdriver

To Install:

1. Install handle by fastening with

screws removed from edge of door.

• If reversing freezer door, remove

door plugs from top edge of door

and insert into screw holes.

To Remove:

1. Remove handle screws with Phillips

screwdriver and retain screws for

later use.

Front Mount Handle - Style 2

Materials Needed:

• Gloves to protect hands

Attach Extensions to Handle: (select models)

1. Align handle and

extension as shown.

2. Place extension in

handle opening.

3. Apply slight pressure

to both sides of the extension piece.

4. Slide extension until it stops on inside edge of

handle.

5. Grasp the handle firmly and slide

down.

1. Grasp the lower part of the handle

firmly, slide up, lift and remove from

the surface.

To Remove:

4. Rotate the handle so that the

handle is flat against the door.

Notes:

• There is a slight curve to

this style of freezer

handle.

• For proper installation, be

sure handle is oriented as shown.

Front Mount Freezer Handle

Materials Needed:

• Gloves to protect hands.

To Install:

1. The handles are to be oriented

as shown.

2. Align door handle clip with the

door studs.

3. Ensure the large hole in the

mounting clip is positioned

down on both ends of the

handle.

Door

Stud

6

Installation

To Install:

1. Align drawer handle clips to the left of the studs

attached to the freezer drawer.

2. Ensure the large hole in the mounting clip is

positioned to the right on both ends of the handle.

3. Rotate the handle so the left base is flat against

the door.

4. Grasp the handle firmly and slide handle to the

right.

Handle

Clip

Door

Stud

To Remove:

1. With both hands, firmly grasp the handle toward

the right side.

2. Slide toward the left, lift and remove from the

surface.

Handle Removal

Euro Handles

This handle style is installed at the factory

Materials Needed:

•

3

⁄32” Allen wrench

To Remove:

• Remove set screw from handle

mounting post using

3

⁄32” Allen

wrench.

• Repeat the procedure on all posts

to remove the handle.

To Replace:

• Align handle with the mounting posts.

• Fully tighten all set screws to secure handle

in place.

Opening and Closing Your

Fresh Food Doors

(select models)

Your new refrigerator is uniquely

designed with two fresh food doors.

Either door can be opened or closed

independently of one another.

There is a vertically-hinged section

on the left fresh food door. When

the left door is closed, the hinged

section automatically forms a seal

between the two doors when both

doors are closed.

When the left door is opened, the hinged seal

automatically folds inward so that it is out of the way.

To avoid electrical shock which can cause severe

personal injury or death, DO NOT attempt to

remove the hinged seal from the fresh food

section.

WARNING

To avoid possible product damage, ALWAYS verify

that the hinged seal is folded against the edge of

the door prior to closing.

CAUTION

Vertically

Hinged Seal

Contact a qualified engineer to perform this task.

WARNING

How to Connect the Water

Supply (select models)

Ice Maker Operation

• To turn ice maker On push arm down from locked

position.

• Lift arm up and lock into position to turn ice maker

Off.

Temperature Controls

Touch Temperature Controls

(select models, style varies by model)

The controls are located at the top front of the

refrigerator compartment.

Control

Initial Control Settings

After plugging the refrigerator in, set the controls.

• Pressing the or pads adjusts the controls

to the desired setting.

• The temperature control range for both

compartments is 1 through 7 (coldest).

• Set the Freezer control on 4.

• Set the Refrigerator control on 4.

• Let the refrigerator run at least 8 to 12 hours before

adding food.

Warm Cabinet Surfaces

At times, the front of the refrigerator cabinet may be

warm to the touch. This is a normal occurrence that

helps prevent moisture from condensing on the

cabinet. This condition will be more noticeable when

you first start the refrigerator, during hot weather and

after excessive or lengthy door openings.

Adjusting the Controls

• 24 hours after adding food, you may decide that one

or both compartments should be colder or warmer. If

so, adjust the control(s) as indicated in the

Temperature Control Guide table below. See page 12

for instructions on checking compartment

temperature.

• Except when starting the refrigerator, do not change

either control more than one number at a time.

• Allow 24 hours for temperatures to stabilize.

Temperature Control Guide

Refrigerator too warm

Refrigerator too cold

Freezer too warm

Freezer too cold

Turn control OFF

Set the Refrigerator control

to next higher number by

pressing the pad.

Set the Refrigerator control

to next lower number by

pressing the pad.

Set the Freezer control to

next higher number by

pressing the pad.

Set the Freezer control to

next lower number by

pressing the pad.

Press the Refrigerator or

freezer pad until a dash

(—) appears in the display.

7

8

Fresh Food Features

Shelves

Your refrigerator has either Spill-Catcher™ or non-

sealed Shelves. The Spill-Catcher™ shelves have a spill

retainer edge which allows for easier clean up and

some are equipped with the Easy Glide

TM

slide out

feature. To slide out (select models), grasp the front of

the shelf and pull forward. Push in the shelf to return

to the original position.

To Remove a Shelf:

• Slightly tilt up the

front and lift up the

rear of the shelf, then

pull the shelf straight

out.

To Lock the Shelf Into Another Position:

• Tilt up the front edge of the shelf.

• Insert the hooks into the desired frame openings and

let the shelf settle into place.

• Be sure the shelf is securely locked at the rear.

Elevator™ Shelf (select models)

The fresh food compartment is equipped with an

Elevator™ shelf.

This shelf can be adjusted up or down without having

to be unloaded of its contents. To adjust an Elevator™

shelf, pull out the knob on the crank handle. Rotate the

crank clockwise to raise the height of the shelf, and

counterclockwise to lower the height of the shelf.

To avoid personal injury or property damage,

observe the following:

• Never attempt to adjust a shelf that is loaded with

food (except in the case of the Elevator™ shelf).

• Confirm shelf is secure before placing items on

shelf.

• Handle tempered glass shelves carefully. Shelves

may break suddenly if nicked, scratched, or

exposed to sudden temperature change.

CAUTION

To Remove:

Completely unload the shelf and pull the shelf forward.

When the shelf stops, press up on the tabs located

underneath its outside edges, then continue pulling

forward, clear of the frame.

To Install:

Align the shelf to the frame and push it all the way

back. (There is no need to depress the tabs for

reinstallation).

In ordinary use, the Elevator™ shelf frame assembly

does not require removal. Though unlikely, and not

recommended, the correct removal procedure is as

follows:

To Remove:

• Unload the shelf completely.

• Remove glass shelf by pulling forward. When shelf

stops lift up and continue pulling forward.

• Manually move the two rear latches toward the shelf

center.

• While supporting the entire shelf and frame from

underneath, lift slightly and rotate the assembly

approximately 30° to allow the rear mechanism to

clear the vertical rear side rails.

• The entire assembly can then be moved forward and

clear of the refrigerator compartment.

To Install:

• Reverse the removal procedure. Be sure the shelf is

in a level position.

• When the sliding shelf is pushed to the rear, it will

reposition the rear latches to their correct operating

position.

Note: Do not raise the shelf to the very top of the

vertical rails, as the shelf may become jammed.

Latches

Slide Out

EasyGlide Shel

fEasyGlide Shelf

TM

(style may vary)

9

Fresh Food Features

Door Storage

Dairy Compartment

The Dairy Compartment provides

convenient door storage for

spreadable items such as butter

and margarine. This compartment

can be moved to different locations to accommodate

storage needs. To use the dairy compartment, raise the

cover.

To Remove:

• Raise the cover, pull upward and tilt out.

To Install:

• Reverse above procedure.

Door Buckets

Door Buckets can be moved to meet storage

needs.

To Remove:

• Slide bucket up and pull straight

out.

To Install:

• Slide bucket in and down until firmly seated in the

door liner.

Full-Width Door Shelf

Full-Width Door Shelf removes for easy cleaning.

To Remove:

• Slide shelf up and pull

straight out.

To Install:

• Reverse above procedure.

Storage Drawers

Crisper Top

The Crisper Top serves as the lower fresh food shelf.

To Remove the Crisper Top:

• Remove crisper drawers as indicated on page 11.

• Place hand under the frame to push up the glass. Lift

glass out.

• Lift frame from refrigerator liner rails.

Beverage Chiller™

(select models)

The Beverage Chiller™ keeps

beverages and other items cooler

than the rest of the fresh food

section. A cold air inlet allows air from the freezer

section to pass into the beverage chiller.

The Beverage Chiller™ control is located

on the left wall of the fresh food

compartment. The control adjusts the

amount of cold air allowed in to the

beverage chiller. For a cooler temperature

in the Beverage Chiller™ slide the control

down.

To Remove:

• First remove the pick off

shelf to the left of the

Beverage Chiller™.

• Firmly hold each side of

beverage chiller, lift up

and away from door liner.

To Install:

• Reverse above procedure.

To Install:

• Repeat above instructions in reverse order.

Snack Drawer (select models)

The Snack Drawer can be used for

storage of miscellaneous items or

extra produce.

To Remove:

• Pull drawer out to full extension. Tilt up

front of drawer and pull straight out.

To Install:

• Insert drawer into frame rails and push back into

place.

10

Fresh Food Features

Humidity-Controlled Crisper Drawers

The Crisper Drawers provide a higher humidity

environment for fresh fruit and vegetable storage.

Controls

The Crisper Controls regulate the amount of humidity

in the crisper drawer. Slide the control toward the Fruit

setting when storing produce with outer skins. Slide

the control toward the Vegetable setting when storing

leafy produce.

Note: For best results, keep the crisper drawers

tightly closed.

To Remove:

• Pull drawer out to full extension. Tilt up front of

drawer and pull straight out.

To Install:

• Insert drawer into frame rails and push back into

place.

Temperature-Controlled Drawer

(select models)

The deli drawer is a full-width drawer with adjustable

temperature control. This drawer can be used for large

party trays, deli items, beverages or miscellaneous

items.

There is a temperature control which adjusts the

amount of cold air allowed into the drawer. The

control is located on the right side of the drawer.

Depending on your model, it is either on the front of

the drawer or under the lid.

Set the control to cheese or to provide a normal

refrigerator temperature. Set the drawer on the

meats or setting when a temperature colder than

the main refrigerator compartment is desired. Use the

coldest setting when storing meats.

To Remove:

• Lift lid (select models). Pull drawer out to full

extension. Tilt up front of drawer and pull straight

out.

To Install:

• Push metal glide rails to the back of the refrigerator

(select models). Place drawer onto rails and slide

drawer back until it falls into place.

Some models feature a divider to organize the drawer

into sections.

To Remove:

• Pull drawer completely out and raise the front of the

divider to unhook it from the rear wall of the drawer

and lift it out.

To Install:

• Hook back of divider over rear wall of the drawer and

lower into place.

Notes:

• Cold air directed to the drawer can decrease

refrigerator temperature. Refrigerator control may

need to be adjusted.

• Do not place leafy vegetables in the drawer.

Colder temperatures could damage leafy produce.

Accessories (select models)

Wine Trivet/Can Rack

The Wine Trivet/Can Rack

accessory fits in the deli drawer or

on a shelf.

Bottles or cans can be laid

crosswise, or a single bottle may be

laid in the center depression.

Egg Cradle

The Egg Cradle (style may vary/select models) holds a

“dozen-plus” eggs. It can be removed to carry to work

area or to be washed.

11

Freezer Features

Accessories (select models)

Ice Cube Tray

The Ice Cube Tray provides an area

to freeze cubes for manual

dispensing of ice.

To release ice cubes from tray, hold tray upside down

over a storage container and twist both ends of tray

until cubes release.

The Ice Service Rack (select models) holds the ice

cube tray.

To Install:

• Slide L-shaped groove of shelf

down over back wall screw.

Push rack back until screw is

stopped in L-shaped groove

(1). Slide front portion of shelf

over front wall screw (2).

To Remove:

• Perform above steps in reverse order.

Shelves and Baskets

Models with swing freezer door:

Freezer Shelf (select models)

Select models have a shelf divider.

To Remove:

• Pull shelf out to full

extension. Tilt up front of

shelf and pull straight out.

To Install:

• Insert shelf into freezer liner rails and push to back

of compartment.

Wire Basket (select models)

To Remove:

• Pull basket out to full

extension. Tilt up front of

basket and pull straight out.

To Install:

• Insert basket into freezer liner rails and push back

into place.

Freezer Door Shelf (select models)

The Freezer Door Shelf provides

convenient storage for frozen food

items in freezer door.

To Remove:

• Lift shelf from side liner tabs and pull

out.

To Install:

• Fit ends of shelf on liner tabs and slide down.

1

2

1

Upper Wire Basket

To Remove:

• Pull upper basket out to full extension and lift out to

remove.

To Install:

• Slide upper basket into freezer. Make sure that rear

of basket hooks behind rail catch.

To prevent accidental child entrapment or

suffocation risk, do not remove the divider in the

top freezer basket.

DANGER

Models with pullout freezer drawer:

12

Food Storage Tips

Fresh Food Storage

• The fresh food compartment of a refrigerator should

be kept between 1°-4° C with an optimum

temperature of 3° C. To check the temperature, place

an appliance thermometer in a glass of water and

place in the center of the refrigerator. Check after 24

hours. If the temperature is above 4° C adjust the

controls as explained on page 7.

• Avoid overcrowding the refrigerator shelves. This

reduces the circulation of air around the food and

results in uneven cooling.

Fruits and Vegetables

• Storage in the crisper drawers traps humidity to help

preserve the fruit and vegetable quality for longer

time periods (see page 10).

• Sort fruits and vegetables before storage and use

bruised or soft items first. Discard those showing

signs of decay.

• Always wrap odorous foods such as onions and

cabbage so the odor does not transfer to other foods.

• While vegetables need a certain amount of humidity

to remain fresh, too much humidity can shorten

storage times (especially leafy vegetables). Drain

vegetables well before storing.

• Wait to wash fresh produce until right before use.

Meat and Cheese

• Raw meat and poultry should be wrapped securely

so leakage and contamination of other foods or

surfaces does not occur.

• Occasionally mold will develop on the surface of

hard cheeses (Swiss, Cheddar, Parmesan). Cut off at

least an inch around and below the moldy area. Keep

your knife or instrument out of the mold itself. Do

not try to save individual cheese slices, soft cheese,

cottage cheese, cream, sour cream or yogurt when

mold appears.

Dairy Food

• Most dairy foods such as milk, yogurt, sour cream

and cottage cheese have freshness dates on their

cartons for appropriate length of storage. Store these

foods in the original carton and refrigerate

immediately after purchasing and after each use.

Frozen Food Storage

• The freezer compartment of a refrigerator should be

kept at approximately -18° C. To check the

temperature, place an appliance thermometer

between the frozen packages and check after 24

hours. If the temperature is above -18° C, adjust the

control as described on page 7.

• A freezer operates more efficiently when it is at least

two-thirds full.

Packaging Foods for Freezing

• To minimize dehydration and quality deterioration use

aluminum foil, freezer wrap, freezer bags or airtight

containers. Force as much air out of the packages as

possible and be sure they are tightly sealed. Trapped

air can cause the food to dry out, change color and

develop an off-flavor (freezer burn).

• Overwrap fresh meats and poultry with suitable

freezer wrap prior to freezing.

• Do not refreeze meat that has completely thawed.

Loading the Freezer

• Avoid adding too much warm food to the freezer at

one time. This overloads the freezer, slows the rate of

freezing and can raise the temperature of frozen

foods.

• Leave space between the packages so cold air can

circulate freely, allowing food to freeze as quickly as

possible.

• Avoid storing hard-to-freeze foods such as ice cream

and orange juice on the freezer door shelves. These

foods are best stored in the freezer interior where the

temperature varies less with door openings.

13

Care and Cleaning

PART

Smooth or Textured Painted

Doors and Exterior

(select models)

Damage to finish due to improper

use of cleaning products or

non-recommended products

is not covered under this

product’s warranty.

Cabinet Interior

Stainless Steel Doors

and Exterior (select models)

Important:

Damage to stainless steel

finish due to improper use

of cleaning products or

non-recommended products

is not covered under this

product’s warranty.

Door Gaskets

Condenser Coil

Remove base grille to access.

Condenser Fan Outlet Grille

See back of refrigerator.

Accessories

Shelves, buckets,

drawers, etc.

To avoid personal injury or property damage,

observe the following:

• Read and follow manufacturer’s directions for all

cleaning products.

• Do not place buckets, shelves or accessories in

dishwasher. Cracking or warping of accessories

may result.

CAUTION

DO NOT USE

Abrasive or harsh cleaners

Ammonia

Chlorine bleach

Concentrated detergents

or solvents

Metal or plastic-textured

scouring pads

Abrasive or harsh cleaners

Ammonia

Chlorine bleach

Concentrated detergents or

solvents

Metal or plastic-textured

scouring pads

Vinegar-based products

Citrus-based cleaners

DO

Use 4 tablespoons of baking soda dissolved in 1

quart (1 liter) warm, soapy water.

Rinse surfaces with clean, warm water and dry

immediately to avoid water spots.

Use warm, soapy water and a soft, clean cloth or

sponge.

Rinse surfaces with clean, warm water and dry

immediately to avoid water spots.

To polish and help prevent fingerprints, follow with

Stainless Steel Magic Spray (part no. 20000008*).

Refrigerator Cleaning Chart

Abrasive or harsh cleaners

Metal or plastic-textured

scouring pads

Anything other than a vacuum

cleaner

A dishwasher

Use a vacuum cleaner hose nozzle.

Use a vacuum cleaner hose nozzle with brush

attachment.

Follow removal and installation instructions from

appropriate feature section.

Allow items to adjust to room temperature.

Dilute mild detergent and use a soft, clean cloth or

sponge for cleaning.

Use a plastic bristle brush to get into crevices. Rinse

surfaces with clean, warm water.

Dry glass and clear items immediately to avoid spots.

Use warm, soapy water and a soft, clean cloth or

sponge.

To avoid electrical shock which can cause severe

personal injury or death, disconnect power to

refrigerator before cleaning. After cleaning,

reconnect power.

WARNING

14

Care and Cleaning

Removing Odors From

Refrigerator

1. Remove all food and turn the refrigerator OFF.

2. Disconnect power to the refrigerator.

3. Clean the walls, floor, ceiling of cabinet interior,

drawers, shelves and gaskets according to the

instructions on page 13.

4. Dilute mild detergent and brush solution into

crevices using a plastic bristle brush. Let stand for

five minutes. Rinse surfaces with warm water. Dry

surfaces with a soft, clean cloth.

5. Wash and dry all bottles, containers and jars.

Discard spoiled or expired items.

6. Wrap or store odor-causing foods in tightly sealed

containers to prevent recurring odors.

7. Reconnect power to refrigerator and return food to

refrigerator.

8. Allow the refrigerator to cool.

9. After 24 hours, check if odor has been eliminated.

If odor is still present:

1. Remove drawers and place on top shelf of

refrigerator.

2. Pack refrigerator and freezer sections – including

doors – with crumpled sheets of black and white

newspaper.

3. Place charcoal briquettes randomly on crumpled

newspaper in both freezer and refrigerator

compartments.

4. Close doors and let stand 24 to 48 hours.

Energy Saving Tips

• Avoid overcrowding refrigerator shelves. This reduces

air circulation around food and causes refrigerator to

run longer.

• Avoid adding too much warm food to refrigerator at

one time. This overloads compartments and slows

rate of cooling.

• Do not use aluminum foil, wax paper, or paper

toweling as shelf liners. This decreases air flow and

causes refrigerator to run less efficiently.

• A freezer that is two-thirds full runs most efficiently.

• Locate refrigerator in coolest part of room. Avoid

areas of direct sunlight, or near heating ducts,

registers or other heat producing appliances. If this is

not possible, isolate exterior by using a section of

cabinet.

• Clean door gaskets every three months according to

cleaning instructions. This will assure that door seals

properly and refrigerator runs efficiently.

• Take time to organize items in refrigerator to reduce

time that door is open.

• Be sure your doors are closing securely by leveling

refrigerator as instructed in your installation

instructions.

• Clean condenser coils as indicated in the cleaning

instructions every three months. This will increase

energy efficiency and cooling performance.

To avoid electrical shock which can cause severe

personal injury or death, disconnect power to

refrigerator before cleaning. After cleaning,

reconnect power.

WARNING

15

Care and Cleaning

To avoid electrical shock which can cause severe

personal injury or death, disconnect power to

refrigerator before replacing light bulb. After

replacing light bulb, reconnect power.

WARNING

To avoid personal injury or property damage,

observe the following:

• Allow light bulb to cool.

• Wear gloves when replacing light bulb.

CAUTION

Replacing Light Bulbs

Fresh Food Section

(style of light shield varies)

1. Slide clear light shield

toward back of

compartment to release

from light assembly.

2. Remove light bulbs.

3. Replace with appliance

bulbs no greater than 40 watts.

4. Replace light shield by aligning edge of shield with

control housing. Slide shield toward front of

refrigerator until it locks into place on ‘T’ shape

locking tab. Do not force shield beyond locking

point. Doing so may damage light shield.

Freezer (style of light shield varies)

1. Reach behind the light

cover.

2. With firm pressure, press

forward on the notches at

the back of the cover and

pull down. The cover will

open from the back.

3. Remove the cover.

4. Remove light bulb.

5. Replace bulb with

appliance bulb no

greater than 40 watts.

6. Insert front tabs of light

cover into slots in freezer

liner and snap rear

portion over light

assembly until rear tab

engages.

16

Care and Cleaning

Upon your return:

After a short vacation or absence:

For models with automatic ice makers:

• Reconnect the water supply and turn on supply valve.

• Monitor water connection for 24 hours and correct

leaks if necessary.

• Restart the ice maker.

• Discard at least the first three ice harvests.

After a long vacation or absence:

• If your refrigerator has an automatic ice maker,

reconnect the water supply and turn on supply valve.

• Plug the refrigerator back in and reset controls

(see page 8).

• Monitor water connection for 24 hours and correct

leaks, if necessary.

• Restart the ice maker.

• Discard ice produced within the first 12 hours (at

least the first three harvests).

Preparing to move:

• Follow the above instructions for long

vacations/absences, through step 6.

• Secure all loose items such as shelves and drawers

by taping them securely in place to prevent damage.

• Tape the doors shut.

• Use an appliance dolly when moving the refrigerator.

ALWAYS truck the refrigerator from its side or back

- NEVER from its front.

• Be sure the refrigerator stays in an upright position

during moving.

If your refrigerator has a dispenser and there is any

possibility that the temperature can drop below

freezing where the refrigerator is located, the water

supply system (including the water tank and the

water valve) must be drained by a qualified servicer.

CAUTION

For short vacations or absences (three months or

less):

1. Remove all perishables.

2. If no one will be checking in on the refrigerator

during your absence, remove all frozen items also.

3. If your refrigerator has an automatic ice maker:

• Shut off the water supply to the ice maker at

least one day ahead of time.

• After the last load of ice drops, raise the wire

shut off arm to the OFF position.

• Empty the ice bin.

4. If the room temperature will drop below 13° C,

follow the instructions for longer absences.

For long vacations, absences (more than three

months) OR if the room temperature will drop

below 13° C:

1. Remove food.

2. If your refrigerator has an automatic ice maker:

• Shut off the water supply to the ice maker at

least one day ahead of time.

• After the last load of ice drops, raise the wire

shut off arm to the OFF position.

• Empty the ice bin.

3. Turn the Freezer control to OFF.

4. Unplug the refrigerator.

5. Thoroughly clean the interior of both compartments

with a baking soda solution and a clean, soft cloth

(four tablespoons of baking soda in one quart of

warm water).

6. Dry thoroughly.

7. Leave the doors open to prevent the formation of

mold and mildew.

Preparing for Vacation

17

Operating Sounds

Improvements in refrigeration design may produce sounds in your new refrigerator that are different or were not

present in an older model. These improvements were made to create a refrigerator that is better at preserving food,

is more energy efficient, and is quieter overall. Because new refrigerators run quieter, sounds may be detected that

were present in older refrigerators, but were masked by higher sound levels. Many of these sounds are normal.

Please note that the surfaces adjacent to a refrigerator, such as hard walls, floors and cabinetry may make these

sounds seem even louder. The following are some of the normal sounds that may be noticed in a new refrigerator.

SOUND

Clicking

Air rushing or

whirring

Gurgling or

boiling sound

Thumping

Vibrating noise

Buzzing

Humming

Hissing or

popping

POSSIBLE CAUSE

• Freezer control (A) clicks when starting or

stopping compressor.

• Motorized device (B) sounds like an electric

clock and snaps in and out.

• Freezer fan (C) and condenser fan (D) make

this noise while operating.

• Evaporator (E) and heat exchanger (F)

refrigerant makes this noise when flowing.

• Ice cubes from ice maker (select models) drop

into ice bucket (G).

• Compressor (H) makes a pulsating sound

while running.

• Refrigerator is not level.

• Ice maker water valve (I) hookup (select

models) buzzes when ice maker fills with

water.

• Ice maker (J) is in the ‘on’ position without

water connection.

• Compressor (H) can make a high-pitched hum

while operating.

• Defrost heater (K) hisses, sizzles or pops when

operational.

SOLUTION

• Normal operation

• See pages 3-4 for details on how to

level your refrigerator.

• Normal operation

• Stop sound by raising ice maker arm

to OFF position.

• Normal operation

J

G

A

F

C

I

E

K

D

H

B

18

Troubleshooting

PROBLEM

Freezer control and

lights are on, but

compressor is not

operating

Crisper drawer

temperature is too

warm

Refrigerator does

not operate

Refrigerator still

won’t operate

Food temperature

is too cold

Food temperature

is too warm

Refrigerator has

an odor

Water droplets

form on outside

of refrigerator

POSSIBLE CAUSES

Refrigerator is in defrost mode.

Control settings are too low.

Refrigerator is not plugged in.

Control is not on.

Fuse is blown, or circuit breaker needs

to be reset.

Power outage has occurred.

Refrigerator is malfunctioning.

Condenser coils are dirty.

Refrigerator or freezer controls are set

too high.

Door is not closing properly.

Controls need to be adjusted.

Condenser coils are dirty.

Rear air grille is blocked.

Door has been opened frequently, or has

been opened for long periods of time.

Food has recently been added.

Compartment is dirty or has odor-

causing food.

Check gaskets for proper seal.

Humidity levels are high.

Controls require adjustment.

WHAT TO DO

Normal operation.

Wait 40 minutes to see if refrigerator restarts.

See page 7 to adjust controls.

Plug in refrigerator.

See page 7 to adjust your controls.

Replace any blown fuses.

Check circuit breaker and reset, if necessary.

Call local power company listing to report outage.

Unplug refrigerator and transfer food to another

refrigerator. If another refrigerator is not available,

place dry ice in freezer section to preserve food.

Warranty does not cover food loss.

Contact service for assistance.

Clean according to the chart on page 13.

See page 8 to adjust your controls.

Refrigerator is not level. See page 3 for details on how

to level your refrigerator.

Check gaskets for proper seal. Clean, if necessary,

according to the chart on page 13.

Check for internal obstructions that are keeping door

from closing properly (i.e. improperly closed drawers,

ice buckets, oversized or improperly stored

containers, etc.)

See page 8 to adjust your controls.

Clean according to the chart on page 13.

Check the positioning of food items in refrigerator to

make sure grille is not blocked. Rear air grilles are

located under crisper drawers.

Reduce time door is open.

Organize food items efficiently to assure door is open

for as short a time as possible.

Allow time for recently added food to reach

refrigerator or freezer temperature.

Clean according to instructions on page 14.

Clean according to the chart on page 13.

Normal during times of high humidity.

See page 7 to adjust your controls.

19

Troubleshooting

PROBLEM

Water droplets form

on inside of

refrigerator

Refrigerator or ice

maker makes

unfamiliar sounds

or seems too loud

Crisper drawers

do not close freely

Refrigerator runs

too frequently

POSSIBLE CAUSES

Humidity levels are high or door has

been been opened frequently.

Check gaskets for proper seal.

Normal operation.

Contents of drawer, or positioning of

items in the surrounding compartment

could be obstructing drawer.

Drawer is not in proper position.

Refrigerator is not level.

Drawer channels are dirty or need

treatment.

Doors have been opened frequently or

for long periods of time.

Humidity or heat in surrounding area is

high.

Food has recently been added.

Refrigerator is exposed to heat by

environment or by appliances nearby.

Condenser coils are dirty.

Controls need to be adjusted.

Door is not closing properly.

Normal Operation

See page 8 to adjust your controls.

Reduce time door is open.

Organize food items efficiently to assure door is open

for as short a time as possible.

Clean, if necessary, according to the chart on page 13.

See page 17.

Reposition food items and containers to avoid

interference with the drawers.

See page 10 for proper drawer placement.

See page 3 for details on how to level your

refrigerator.

Clean drawer channels with warm, soapy water.

Rinse and dry thoroughly.

Apply a thin layer of petroleum jelly to drawer

channels.

Reduce time door is open.

Organize food items efficiently to assure door is open

for as short a time as possible.

Allow interior environment to adjust for period the

door has been opened.

Normal operation.

Allow time for recently added food to reach

refrigerator or freezer temperature.

Evaluate your refrigerator’s environment. Refrigerator

may need to be moved to run more efficiently.

Clean, if necessary, according to the chart on page 13.

See page 8 to adjust your controls.

Refrigerator is not level. See page 3 for details on how

to level your refrigerator.

Check gaskets for proper seal.

Clean, if necessary, according to the chart on page 13.

Check for internal obstructions that are keeping door

from closing properly (i.e. improperly closed drawers,

ice buckets, oversized or improperly stored

containers, etc.)

See Operating Sounds on page 17.

WHAT TO DO

La page charge ...

Amana 5GBR22PRAA Mode d'emploi

Ce manuel convient également à

Amana 5GBR22PRAA Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents