LG DLEC885W Le manuel du propriétaire

DWG.

No.

TRIG.

DR COMPLETED

도면 DR 완료

완료일 :

LG 전자 (주)

LG Electronics Inc.

UNIT SCALE

1

mm

REVIEWEDDESIGNED

RELATED DWG.

CHECKED APPROVED

윤 혜 진 윤 혜 진 한 일 탁

16.07.21 16.07.21 16.07.21

MODELING

I

T

L

E

T

APPROVED

승인자

PREPARED

시방자

DATE

년/월/일

REF. NO.

시방 번호

REV. NO.

기호

REVISION DESCRIPTION

변경 사항

8

RELEASING THIS DRAWING

WITHOUT PERMISSION LG

Electronics SHOULD BE

ACCUSED ACCORDING TO THE

LAWS AND COMPANY RULES.

이 도면은 LG전자의 자산으로 불법

유출시 관계법과 회사규정에 의해 처벌됨.

PDF

ILLUSTRATOR

150

210

MFL67731090

MANUAL,OWNER’S

PRIME PLUS(D) ECI향

1/1

MFL67731090

<< 주기 >>

1. 재질, 인쇄방법, 인쇄도수, 외곽치수등은 작업표에 준한다.

2. 인쇄내용, 문자크기 및 형상, 선의 굵기 등은 설계에서 제시된 FILM에 준함.

3. 외곽치수는 절단후 치수임.

4. 양산전에 설계 한도를 득할 것.

5. 본 부품에 금지물질이 포함되지 않도록 하고, 상세내용은 LG(63)-A-5501-34

를 만족할 것.

<< NOTES >>

1. Material, printing and exterier size are refer to work tables.

2. Printing, text size and line are based on LG design film.

3. Exterier size on the drawing is cutting line.

4. Before product controlled by criteria sample.

5. The part should not contain prohibited substances(Pb,Cd,Hg,Cr+6,PBB,

PBDE) and details should comply with LG standard of LG(63)-A-5501-34

WORK

적용모델

90

재 질 인쇄방법

인 쇄 도 수

표 지 내 지

1도 1도

OFFSET 인쇄

68, A5

PAGE

REMARK

SEC.

RC9066A3F

7

6

5

4

3

2

1

모조지 80g OFFSET 인쇄

ECI향

Enlish

French

지적재산권 보호 문구 삽입

EAGH300991

2017.03.24

윤혜진

정영석

북미 중재강제조항 적용 관련 문구 추가

EAGI100901

2018.01.30

최장안

정영석

신모델 모델명 추가 EAGI700539 2018.07.23

윤혜진 정영석

DRYER

OWNER’S MANUAL

Read this owner’s manual thoroughly before operating the appliance

and keep it handy for reference at all times.

DLEC888W

DLEC888R

DLEC885W

MFL67731090

Rev.03_072318

www.lg.com

2

Ultra Big Capacity Drum

The LG Dryer has a large capacity.

Reduced drying time

Drying time is reduced by the use of an efficient air flow system and

an optimized heater.

Innovative Noise Reduction

The optimized design of the air flow system and the vibration reduction

technology helps to reduce noise.

Ease of Use

The electronic control has a large, easy to read LED display.

Your dryer provides sensor drying and manual drying programs.

Sensor Dry Dryer electronically senses laundry moisture level and automatically determines operation time

based on the dryness of the load and the selected program. The control will change the estimated time

remaining if it senses a large change in the time needed to complete the cycle. These large increases or

decreases in the time display are normal, and do not indicate a product malfunction.

Manual Dry Manual Dry allows you to set the desired dry time manually. Certain types of loads, such as

large and/or bulky loads, may not dry properly using Sensor Dry. These loads should be dried using the

Manual Dry feature to ensure complete drying.

What are Sensor Dry and Manual Dry?

C

F

ontents

F

eatures

Safety Instructions .................................................................................. 3

Installation Instructions ............................................................................ 7

Electrical Requirement .......................................................................... 11

Appearance And Design ....................................................................... 14

Operating Your Dryer ............................................................................ 15

Additional Functions............................................................................... 18

Caring For Your Dryer ........................................................................... 22

Additional Tips For Smart Use .............................................................. 25

Troubleshooting Guide .......................................................................... 27

Technical Data ....................................................................................... 32

Warranty ................................................................................................ 33

Safety Instructions

3

S

F

afety Instructions

READ ALL INSTRUCTIONS BEFORE USE

BASIC SAFETY PRECAUTIONS

Your Safety and the safety of others is very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey

all safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word DANGER or WARNING.

These words mean:

DANGER:

You can be killed or seriously injured if you don’t immediately follow instructions.

WARNING:

You can be killed or seriously injured if you don’t follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell

you what can happen if the instructions are not followed.

WARNING

For your safety, the information in this manual must be followed to minimize the

risk of fire or explosion, electric shock, or to prevent property damage, personal

injury, or loss of life.

WARNING

To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following:

• Do not install a clothes dryer with flexible

plastic venting materials. If flexible metal (foil

type) duct is installed, it must be of a specific

type identified by the appliance manufacturer as

suitable for use with clothes dryers. Flexible

venting materials are known to collapse, be

easily crushed, and trap lint. These conditions

will obstruct clothes dryer airflow and increase

the risk of fire.

• Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this

appliance or any other appliances.

• Installation and service must be performed by a

qualified installer, service agency, or the gas

supplier.

• Install the clothes dryer according to the

manufacturer’s instructions and local codes.

• Save these instructions.

• Certain internal parts are intentionally not grounded

and may present a risk of electronic shock only

during serving.

Service personnel - do not contact the following

parts while the appliance is energized: Motor

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of

malfunction or breakdown, grounding will reduce the

risk of electric shock by providing a path of least

resistance for electric current. This appliance must be

equipped with a cord having an equipment-grounding

conductor and a grounding plug. The plug must be

plugged into an appropriate outlet that is properly

installed and grounded in accordance with all local

codes and ordinances.

Do not modify the plug provided with the appliance. If it

will not fit the outlet, have a proper outlet installed by a

qualified electrician.

This appliance must be connected to a grounded metal,

permanent wiring system or an equipment-grounding

conductor must be run with the circuit conductors and

connected to the equipment-grounding terminal or lead

on the appliance. Electrical shock can result if the dryer

is not properly grounded.

Safety Instructions

4

S

F

afety Instructions

• Read all instructions before using the dryer.

• Before use, the dryer must be properly

installed as described in this manual.

• Do not place items exposed to cooking oils in

your dryer. Items contaminated with cooking

oils may contribute to a chemical reaction that

could cause a load to catch fire.

• Do not dry articles that have been previously

cleaned in, washed in, soaked in, or spotted

with gasoline, dry-cleaning solvents, or other

flammable or explosive substances as they

give off vapors that could ignite or explode.

• Do not reach into the dryer if the drum or any

other part is moving.

• Do not repair or replace any part of the dryer

or attempt any servicing unless specifically

recommended in this Use and Care Guide or

in published user-repair instructions that you

understand and have the skills to carry out.

• Do not tamper with controls.

• Before the dryer is removed from service or

discarded, remove the door to the drying

compartment.

• Do not allow children to play on or in the dryer.

Close supervision of children is necessary

when the dryer is used near children.

• Do not use fabric softeners or products to

eliminate static unless recommended by the

manufacturer of the fabric softener or product.

• Do not use heat to dry articles containing foam

rubber or similarly textured rubber-like

materials.

• Keep area around the exhaust opening and

adjacent surrounding areas free from the

accumulation of lint, dust, and dirt.

• The interior of the dryer and exhaust vent

should be cleaned periodically by qualified

service personnel.

• Do not install or store the dryer where it will be

exposed to the weather.

• Always check the inside of the dryer for foreign

objects.

• Clean lint screen before or after each load.

• Do not spray dry cleaning detergent directly

onto the product or use the product to dry

clothes left with dry cleaning detergent. Doing

so could result in explosion or fire.

• Do not dry clothes stained with combustible

materials such as thinners, benzene, solvent,

or flammable materials. Doing so could result

in explosion or fire.

(e.g. flammable cleaning solutions, acetone,

alcohol, benzene, gasoline, stain-removing

turpentine, wax, wax removers, hair gel, hair

spray, edible oils, oil, creams, cosmetic

products and lotions, oil stains)

• Do not dry clothes stained with oil substances.

Oil substances (including edible oils) stained

on clothes cannot be completely removed

even after washing with water, and could result

in fire.

• Remove clothes from the product immediately

when drying is complete or the power is turned

off during the drying process.

• Leaving clothes that has been dried in the

product unattended could result in fire.

• Clothes removed from the product after drying

could result in fire. Remove clothes

immediately after drying, and then hang or lay

the clothes flat to cool.

BASIC SAFETY PRECAUTIONS

WARNING

To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following:

WARNING

Improper connection of the equipment-grounding conductor can result in a risk of

electric shock. Check with a qualified electrician or service person if you are in

doubt as to whether the appliance is properly grounded.

Safety Instructions

5

S

F

afety Instructions

WARNING

To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following:

SAFETY INSTRUCTIONS FOR INSTALLATION

• Properly ground dryer to conform with all

governing codes and ordinances. Follow

details in the installation instructions. Electrical

shock can result if the dryer is not properly

grounded.

• Before use, the dryer must be properly

installed as described in this manual.

Electrical shock can result if the dryer is not

properly grounded.

• Install and store the dryer where it will not

be exposed to temperatures below freezing

or exposed to the weather.

• All repairs and servicing must be performed

by an authorized servicer unless

specifically recommended in this Owner’s

Guide. Use only authorized factory parts.

Failure to follow this warning can cause serious

injury, fire, electrical shock, or death.

• To reduce the risk of electric shock, do not

install the dryer in humid spaces. Failure to

follow this warning can cause serious injury,

fire, electrical shock, or death.

• Connect to a properly rated, protected, and

sized power circuit to avoid electrical

overload. Improper power circuit can melt,

creating electrical shock and/or fire hazard.

• Remove all packing items and dispose of all

shipping materials properly. Failure to do so

can result in death, explosion, fire, or burns.

• Place dryer at least 18 in. above the floor for

a garage or basement installation. Failure to

do so can result in death, explosion, fire, or

burns.

• Keep all packaging from children. Packaging

material can be dangerous for children. There is

a risk of suffocation.

• Do not install nearby heat item. Such as

stove, cooking oven. Failure to do so can cause

damage, smoke, and fire.

• Do not place candle and cigarettes on top of

the product. Failure to do so can cause

damage, smoke, and fire.

• Remove all protective vinyl film from the

product. Failure to do so can cause damage,

smoke, and fire.

• Certain internal parts are intentionally not

grounded and may present a risk of electronic

shock only during serving.

Service personnel - do not contact the following

parts while the appliance is energized: Motor

READ ALL INSTRUCTIONS BEFORE USE

Safety Instructions

6

S

F

afety Instructions

SAVE THESE INSTRUCTIONS

WARNING

To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following:

• Do not, under any circumstances, cut or

remove the ground prong from the power cord.

To prevent personal injury or damage to the

dryer, the electrical power cord must be

plugged into a properly grounded outlet.

• For personal safety, this dryer must be properly

grounded. Failure to do so can result in

electrical shock or injury.

• Refer to the installation instructions in this

manual for specific electrical requirements for

your model. Failure to follow these instructions

can create an electrical shock hazard and/or a

fire hazard.

• This dryer must be plugged into a properly

grounded outlet. Electrical shock can result if

the dryer is not properly grounded. Have the

wall outlet and circuit checked by a qualified

electrician to make sure the outlet is properly

grounded. Failure to follow these instructions

can create an electrical shock hazard and/or a

fire hazard.

• The dryer should always be plugged into its

own individual electrical outlet which has a

voltage rating that matches the rating plate.

This provides the best performance and also

prevents overloading house wiring circuits

which could cause a fire hazard from

overheated wires.

• Never unplug your dryer by pulling on the

power cord. Always grip plug firmly and pull

straight out from the outlet. The power cord can

be damaged, resulting in a risk of fire and

electrical shock.

• Repair or replace immediately all power cords

that have become frayed or otherwise

damaged. Do not use a cord that shows cracks

or abrasion damage along its length or at either

end. The power cord can melt, creating

electrical shock and/or fire hazard.

• When installing or moving the dryer, be careful

not to pinch, crush, or damage the power cord.

This will prevent injury and prevent damage to

the dryer from fire and electrical shock.

SAFETY INSTRUCTIONS FOR INSTALLATION

Installation Instructions

7

I

F

nstallation Instructions

The following instructions will help guide you through the initial steps of setting up your dryer for use.

Please note that every section of this manual provides important information regarding the preparation and use of

your dryer, and it is important that you review this entire manual before proceeding with any installation or use.

More detailed instructions concerning electrical connections, gas connections, and exhaust requirements are

provided in other parts of this manual.

Choose a location with a solid floor for your dryer. Place the dryer at least eighteen inches above the floor for a

garage installation. After placing the dryer in the desired location, make sure that it has the required clearances

shown.

Positioning the Dryer.

Leveling legs should be secured.

All four legs should be on a solid, even floor and properly leveled as shown in this manual.

If dryer is not level, laundry may not be able to accurately detect the moisture level in the clothes.

When leveling, please be cautious to avoid injury.

Note

33

1

/2"

(850 mm)

23

5

/8"

(600 mm)

25

1

/4"

(640 mm)

8

Installation Instructions

Prior to the first use of this appliance, use all-purpose

cleaning products or a solution of detergent and water,

with a damp cloth to remove from the inside of the

dryer drum/drying compartment any dust or dirt that

may have accumulated in the inside of the dryer. Plug

in your dryer after reviewing the following parts on your

dryer’s Electrical Requirements.

Close the door to the dryer drum/drying

compartment and, after completing all steps in this

manual for proper installation of this dryer, start the

dryer on a heat setting, as described more fully in

the operating instructions that accompany the dryer.

The following instructions are applicable to

installations of the dryer in a manufactured or

mobile home. Any installation in a manufactured

or mobile home must comply with the

Manufactured Home Construction and Safety

Standards Title 24 CFR, Part 32-80 or Standard

CAN/CSA Z240 MH and local codes and

ordinances. If you are uncertain whether your

proposed installation will comply with these

standards, please contact a service and installation

professional for assistance.

1) The electrical connection for an electric dryer

must be a 4-wire connection. More detailed

information concerning the electrical connection

is provided at the manual section entitled

Electrical Requirements for Electric Dryer

Following are several warnings and instructions

concerning making the electrical connection for

electric dryers. More detailed information

concerning the electrical connection is provided at

the manual section entitled Electrical Requirements

For Electric Dryer and it is important that you

thoroughly review that section, and the remainder of

this manual, before taking any steps to install or use

this dryer.

1. Use only a new U.L. listed No. 10 (copper wire

only) conductor power supply cord kit rated 230

Volts (minimum) 30 Amperes and labeled as

suitable for use in a clothes dryer.

2. 4-wire cord is required for manufactured (mobile)

home installations and use and where local codes

do not allow grounding of this appliance through

neutral. As well as all new construction after

January 1, 1996.

3. For additional instruction on connecting the dryer

to an electrical power source, please refer to this

manual’s section on Electrical Requirements for

Electric Dryer.

Confirming Heat Source

Operation

Additional Instructions

for Installation of Your

Dryer in a Manufactured

or Mobile Home

Electrical Connections

I

F

nstallation Instructions

Preparation of the Dryer

WARNING

• Use a new UL approved 30 amp power

supply cord or 10 gauge solid copper wire.

• Use a UL approved strain relief.

• Disconnect power before making electrical

connections.

• Connect neutral wire (white or center) to

center terminal.

• Ground wire (green or bare) must be

connected to green ground connector.

• Securely tighten all electrical connections

• See installation instructions for complete

instructions.

• A 4-wire connection is required for all

mobile and manufactured home

installations, as well as all new construction

after January 1, 1996.

• Failure to do so can result in fire or

electrical shock.

9

Installation Instructions

I

F

nstallation Instructions

Shape

and

assembly

direction

21

7

/8 inch

(550mm)

Washer Top plate size

23

5

/8 inch

(600mm)

Stacking Kit

In order to stack this dryer an LG stacking kit is

required.

This dryer may only be stacked on top of an LG

washer. DO NOT attempt to stack this dryer on any

other washer, as damage, injury or property damage

could result.

Installation Procedure

1. Place the LG dryer on the LG washing machine.

2. Remove the two screws from the bottom of the rear

cover on each side as illustrated below.

3. Align the stacking kit holes and the rear cover

holes.

3-1) 23

5

/8 inch(600mm)

3-2) 21

7

/8 inch(550mm)

• Fasten the 2 screws that were removed earlier

from the dryer to the stacking kit.

• Use 4 screws in accessory box [0.6inch(16mm)]

to assemble washer rear cover and stacking kit.

• The procedure for the opposite side will be the

same.

WARNING

• Incorrect installation can cause serious

accidents.

• The weight of the dryer and the height of

installation makes the stacking procedure

too risky for one person. This procedure

should be performed by 2 or more

experienced service personnel.

• The dryer is not suitable for a built-in

installation. Please do not install as a built-

in appliance.

• Do not operate if the dryer is disassembled.

Dryer

Washer

Installation Instructions

10

Level the dryer

1. Level the dryer is to prevent undesirable noise

and vibration.

Locate your dryer on a solid, level floor. Make

sure it is not subjected to splashing water or

freezing temperatures. Do not store flammable

materials near the dryer.

2. If the dryer is not properly level, adjust the front

leveling legs up and down as necessary.

Turn the legs clockwise to raise the dryer and

counterclockwise to lower the dryer. Check the

dryer diagonally to make sure it does not rock

either way. Readjust the legs if necessary.

Diagonal Check

When pushing down corners of the dryer,

the machine should not move at all.

(Check in either direction.)

If machine rocks when pushing the machine top plate

diagonally, adjust the feet again.

Adjustable feet

Adjustable feetAdjustable feet

Raise Lower

I

F

nstallation Instructions

❊

Electrical Requirement For Electric Dryers

11

E

F

lectrical Requirement

CONNECTING ELECTRIC DRYERS

Special Electrical Requirements for

Mobile or Manufactured Homes

• This dryer must be connected to a grounded metal,

permanent wiring system, or an equipment-

grounding conductor must be run with the circuit

conductors and connected to the equipment-

grounding terminal or lead on the dryer. Failure to do

so can result in fire, explosion, or death.

• The dryer has its own terminal block that must be

connected to a separate 230 VAC, 60-Hertz,

single-phase circuit, fused at 30 amperes (the circuit

must be fused on both sides of the line.)

ELECTRICAL SERVICE FOR THE DRYER SHOULD

BE OF THE MAXIMUM RATE VOLTAGE LISTED ON

THE NAMEPLATE. DO NOT CONNECT DRYER TO

110-, 115-, OR 120-VOLT CIRCUIT. Heating elements

are available for field installation in dryers which are

to be connected to an electrical service of a different

voltage than that listed on the rating plate. Failure to

follow these instructions can result in fire, explosion, or

death.

• If branch circuit to dryer is 15 ft. (4.5 m) or less in

length, use UL (Underwriters Laboratories) listed No.-

10 AWG wire (copper wire only), or as required by

local codes. If over 15 ft. (4.50 m), use UL-listed

No.-8

AWG wire (copper wire only), or as required by local

codes. Allow sufficient slack in wiring so dryer can be

moved from its normal location when necessary.

Failure to do so can result in fire, explosion, or death.

• The power cord (pigtail) connection between wall

receptacle and dryer terminal block IS NOT supplied

with dryer. Type of pigtail and gauge of wire must

conform to local codes and with instructions on the

following pages. Failure to follow these instructions can

result in fire, explosion, or death.

• A 4-wire connection is required for all mobile and

manufactured home installations, as well as all new

construction after January 1, 1996. A 4-wire

connection must be used where local codes do not

permit grounding through the neutral wire. Failure to

do so can result in fire, explosion, or death.

• Do not modify the plug and internal wire provided with

the dryer.

• If it does not fit the outlet, a proper outlet will need to be

installed by a qualified electrician.

• Any installation in a manufactured or mobile home

must comply with the Manufactured Home

Construction and Safety Standards Title 24 CFR, Part

32-80 or Standard CAN/ CSA Z240 MH and local

codes and ordinances.

• A 4-wire connection is required for all mobile and

manufactured home installations, as well as all

new construction after January 1, 1996.

Failure to do so can result in fire, explosion, or death.

WARNING

To help prevent fire, electric shock, serious

injury, or death, the wiring and grounding

must conform to the latest edition of the

National Electrical Code, ANSI/NFPA 70 and

all applicable local regulations. Please

contact a qualified electrician to check your

home’s wiring and fuses to ensure that your

home has adequate electrical power to

operate the dryer.

WARNING

To reduce the risk of fire, electric shock, or

injury to persons when using this appliance,

follow basic precautions, including the

following:

WARNING

To reduce the risk of fire, electric shock, or

injury to persons when using this appliance,

follow basic precautions, including the

following:

Electrical Requirement For Electric Dryers

12

E

F

lectrical Requirement

Use the instructions in this section if your home has

a 3-wire receptacle (NEMA type 10-30R) and you

will be using a UL listed, 115/230 volt minimum, 30

amp, dryer power supply cord.

Review the following options to determine the appropriate electrical

connection for your home:

Use the instructions in this section if your home has

a 4-wire receptacle (NEMA type 14-30R) and you

will be using a UL listed, 115/230 volt minimum, 30

amp, dryer power supply cord.

4-wire receptacle

(NEMA type14-30R)

3-wire receptacle

(NEMA type10-30R)

• Be sure the screws of the terminal block are

tightened firmly. Failure to properly tighten the

screws can result in fire, or property damage.

• If you are not sure of the power supply wires or

cannot tell which are hot and neutral, consult a

qualified electrician.

• If you are not sure if your electric outlet is wired

properly, consult a qualified electrician.

Connecting the power supply incorrectly can

result in product damage, fire, injury or death.

• Direct wiring is not permitted by code in most

locations. It is the customer's responsibility to

ensure that the installation meets all local codes.

Note

1. Connect neutral wire (white) of power cord to center

terminal block screw.

2. Connect red and black wire to the left and right

terminal block screws.

3. Connect ground wire (green) of power cord to

external ground screw and move neutral ground wire

of appliance and connect it to center screw.

4. Make sure that the strain relief screw is tightened and

be sure that all terminal block nuts are on tight and

power cord is in right position.

• lf your local codes or ordinances do not allow the

use of a 3 wire connection, or you are installing

your dryer in a mobile home, you must use a 4-

wire connection.

4-Prong plug

: 4-wire connection with

a Power supply cord.

Electrical Requirement For Electric Dryers

13

E

F

lectrical Requirement

1. Connect neutral wire (white) of power cord to

center terminal block screw.

2. Connect ground wire of appliance and neutral

wire of power cord to center terminal block screw.

3. Connect red and black wire to the left and right

terminal block screws.

4. Make sure that the strain relief screw is tightened.

and be sure that all terminal block nuts are on

tight and power cord is in right position.

lf your local codes or ordinances permit the

connection of a frame-grounding conductor to the

neutral wire, use these instructions. If your local

codes or ordinances do not allow the connection of

a frame-grounding conductor to the neutral wire,

use the instructions under

Section 3: Optional 3-wire connection.

: 3-Wire Connection with

a Power Supply Cord

• If your local codes or ordinances do not allow the

connection of a frame-grounding conductor to the

neutral wire, use the instructions under this

section.

: Optional 3-wire

connection.

Appearance And Design

14

A

F

ppearance And Design

Control Panel

Additional Function Buttons

• More Time • Time Delay

• Less Time • Custom PGM

• Option • Wrinkle Care

• Signal • Drum Light

LED Display

• Time Display

• Indicator Lamps

Control Panel

Start/Pause

Power

Cycle Selector Knob

Water Container

Door

Condenser Cover

Air Ventilation Grill

Operating Your Dryer

15

O

F

perating Your Dryer

Cycle Selection Table

CAUTION

If the load is less than 2.2lbs (1kg), please use Warm course in MANUAL DRY course.

Your wool should be used in Wool program and heat-sensitive fabrics including silk, underwears,

lingerie should be used in Delicates course.

And also please comply with the recommended laundry load when you use the special fabric

course. (Refer to page 25) Otherwise, these clothes may not dry properly.

Cotton

Mixed Fabrics

Cool Air

Sports Wear

Wool

Easy Care

Delicates

Warm Air

Quick Dry

Gentle Air

Soft Care

Jeans

Bulky Items

SENSOR DRY CYCLES

Very

More

Normal

Damp

Normal

Less

Damp

More

Normal

Damp

-

Drying

Level

High

Medium

High

Medium

Low

Ultra Low

High

-

Adjustable

Ultra Low

Medium

High

Medium

High

Temp.

Quilts, small comforters and

blankets

For thick and quilted fabrics

Terry towels, tea towels,

towels, bed linen

For thick and quilted fabrics which do not need to be ironed

Shirts, T-shirts, trousers,

under-wear and socks

For polyamide, acrylic, and polyester that do not need to be

ironed

Shirts, T-shirts, under-wear,

anoraks and socks

For polyamide, acrylic, polyester that do need to be ironed

Bath towels, tea towels,

underwear, cotton socks

For fabrics which do not need to be ironed

Sheets, pillowcase, towels For fabrics which do not need to be ironed

Bed linen, table linen, towels,

T-shirts, polo shirts, and work

clothes

For fabrics which do need to be ironed

Bed linen, table linen,

tracksuits, parka, blankets

For thick and quilted fabrics which do not need to be ironed

A kind of linen and towel

except for the special fabrics

For the small loads of qualified fabrics with short drying times

Shirts, blouses For fabrics which do not need to be ironed

Trousers, dresses, skirts,

blouses

For fabrics which do need to be ironed

All fabrics that need to be fluffed without heat

Athletic uniform, training wear

Wool

For polyester material

For wool fabrics

Silk, Women's thin clothes,

lingerie

For fabrics which are heat-sensitive like synthetic fabrics

Bath towels, bath robes,

dishclothes, quilted fabrics

made of acrylic

Small clothes and pre-dried laundry normal fabrics using hot

temperature

Silk, wool, delicate lingerie

Refreshes clothes without tumble drying

(It can use the dryer rack.)

T-shirts, pillowcase, and

towels

For cotton fabrics which do not need to be ironed

Jeans and colour fading

garments.

For jeans which do not need to be ironed

Bed clothes, sheets For bulky items

MANUAL DRY CYCLES

Operating Your Dryer

16

O

F

perating Your Dryer

BEFORE YOU USE YOUR DRYER

1. When unpacking your dryer, make sure there is no visible damage to the machine.

2. Follow the installation instructions and use a level to ensure proper installation.

3. Check the water reservoir, condenser, door, gasket and drum for signs of damage.

4. Run the dryer for a few minutes to make sure it is heating properly.

1. Turn power on.

First, press the Power button. The indicator light

above the button will become illuminated,

indicating that the machine is ready set to run.

2. Open the door.

3. Check the lint filter, water

container, and condenser.

The lint filter near the door, should be emptied

before drying operation.

Open and check if lint filter is cleaned.

If not, clean it referring to page 22.

Water container and condenser are also checked

to be emptied and cleaned for better drying result.

4. Place laundry into the drum after

sorting.

The clothes should be sorted by fabric type and

dryness level and all the strings and belts of

clothes should be secured before being put into

the drum.

Push the laundry all the way back to keep it away

from the door seal.

If not, the door seal and clothes may be damaged.

Turn the

dryer on.

Open the

door.

Check the

lint filter.

Operating Your Dryer

17

O

F

perating Your Dryer

5. Close the Door.

Before you close the door, make sure fabrics are

properly loaded and not caught in the door opening.

6.

Select the Drying Cycle you want.

You can choose a cycle by turning the Cycle Selector

Knob until the required program reaches to its indicator.

If you press Start/Pause button without choosing any

cycle, the dryer will proceed with the Cotton program.

[Please refer to following Cycle Selection Table (page 15)

for the detailed information]

7 . Press the

SSttaarrtt//PPaauussee

button.

You can hear the drum turning.

8.

After operation is completed, open the

door and remove the laundry.

Be careful! Drum inside could be still hot.

(Operation time varies depending on your cycle

selection or options.)

9. Clean the lint filters and

empty water container.

The lint filter should be cleaned after each load.

10. Turn off the Dryer.

Press the Power button.

Select the

desired

cycle.

Take out

the laundry.

Clean the

door lint

filter.

CAUTION

• Be careful the filter is not torn or damaged

when using a vacuum cleaner. If there is a

little residue buildup on filter, you can scrub

lint screen with a brush to remove.

• If you want to open the door while dryer is

operating, please press the Start/Pause

button first, wait until drum completely

stops and then open the door.

Additional Functions

18

A

F

dditional Functions

Note

You can only save one Custom PGM

program at a time. If you press and hold the

Custom PGM button for 3 seconds, you will

overwrite any previously stored Custom

PGM settings.

Once Custom PGM has been recalled, any of

the memorized modifiers or options can be

adjusted. However, if the Cycle Selector

Knob is rotated, Custom PGM will be

cancelled.

Note

If the door is opened during the drying portion

of a cycle before Wrinkle Care has started, the

cycle will not be cancelled and Wrinkle Care

will begin as soon as the normal drying portion

of the cycle is completed.

Time Delay

The Time Delay feature allows you to have the

dryer run at a time that is more convenient, for

example when electricity rates are cheaper.

The cycle can be delayed from 3 hours up to a

maximum of 19 hours.

1. Load the dryer and close the door.

2. Press the Power button.

3. Select the desired cycle and options.

4. Press the Time Delay button until the

desired delay time is displayed.

5. Press the Start/Pause button.

Wrinkle Care ( )

Selecting this option will tumble the load

periodically for a few seconds without heat.

This will continue for up to 2 hours after the

selected cycle, or until the door is opened.

This prevents wrinkling of unremoved dry

items until they can be removed.

Custom PGM

If you have a special combination of settings

that you use frequently, you can save these

settings as a Custom PGM.

*

To Save a Custom PGM

1. Turn on the dryer.

2. Select a cycle.

3. Use the cycle modifier buttons to adjust the

settings for that cycle.

4. Set any other desired cycle options.

5. Press and hold the Custom PGM button for 3

seconds. You will hear two beeps to confirm

the settings have been stored.

To Recall a Custom PGM

1. Press and release the Custom PGM button.

The stored settings will be displayed.

2. Press and release the Cycle Selector Knob to

start the cycle. The dryer will start

automatically.

Additional Functions

19

A

F

dditional Functions

More Time / Less Time

The More Time and Less Time buttons can

be used to increase or decrease the dry time

when MANUAL DRY cycles are selected.

These buttons are disabled once the cycle is

started.

Options

Gentle

- This function keeps the garments more moist

than the standard Iron dry level.

- Cotton, Mixed Fabircs and Easy Care cycles.

Damp Dry Signal

- This option causes the control to beep once

the clothes have reached a "Damp Dry Signal"

level. This can be used to alert you to remove

articles that you don't want to over dry or that

you want to have damp for easier ironing.

- Cotton, Mixed Fabircs and Easy Care cycles.

Note

These buttons are available only with

MANUAL DRY, before you push

Start/Pause button.

Drum Light

Press the Drum Light button to turn on the

drum light during dryer operation. This will

allow you to more easily observe the load.

The drum light will come on any time the

door is opened.

Signal

Press the Signal button to adjust the volume of

the signals from high to off.

Child Lock( )

Use this option to prevent cycle settings from

being changed while the dryer is operating.

Press and hold the Dry Level button for 3

seconds to activate or deactivate the Child Lock

function.

The lock icon will be shown in the display, and

all controls are disabled.

Temp.

Adjusts the temperature setting from Ultra Low

to High. This allows precise care of your fabrics

and garments.

• Press the Temp. button repeatedly to scroll

through available settings.

La page charge ...

LG DLEC885W Le manuel du propriétaire

LG DLEC885W Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents