VTech VC2105 Mode d'emploi

Marque: VTech

Modèle: VC2105

Catégorie: Moniteurs vidéo bébé

Taper: Mode d'emploi

• To keep this product working well and looking good, follow these guidelines:

• Avoid placing it near heating appliances and devices that generate electrical noise (for example,

motors or ﬂuorescent lamps).

• DO NOT expose it to direct sunlight or moisture.

• Avoid dropping the product or treating it roughly.

• Clean with a soft damp cloth.

• DO NOT immerse the parent unit and the baby unit in water and do not clean under running water.

• DO NOT use cleaning spray or liquid cleaners.

• Make sure the parent unit and the baby unit are dry before you connect them to the mains again.

When you are not going to use the video monitor for some time, store the parent unit, the baby unit

and the power adapters in a cool, dry location.

Below are the questions most frequently asked about the video monitor.

Can I turn the parent

unit display screen

off but keep hearing

sounds from the baby

unit?

Yes, press | LCD ON/OFF on the parent unit to turn off the screen. The parent

unit display will also dim automatically after being inactive for some time. In both

instances, you will still be able to hear all sounds from the baby unit.

Press any key to turn the screen back on.

Why is the baby

unit not responding

normally?

Try the following (in the order listed) for a common cure:

1. Disconnect the power to the baby unit.

2. Wait a few minutes before connecting power back to the baby unit.

3. Reboot the parent unit.

Why is my screen in

black and white?

The baby unit has a light sensor that measures ambient light. When the

ambient light is dim, such as during night time or in a dark room, the baby unit

activates its infrared LEDs, and displays the camera images in black and white

night vision.

Why does my baby unit

show ofﬂine? Why is the

connection lost every

now and then?

The baby unit may have lost connection to the Wi-Fi router. Check your

network and router settings.

Other electronic products may cause interference with your baby unit. Try

installing your baby unit as far away from these electronic devices as possible.

Why can’t I hear a

sound/Why can’t I hear

my baby crying?

The parent unit speaker volume may be too low. Press on the parent unit

to increase the volume.

You may have set a low sound sensitivity level. Set the sound sensitivity to a

higher level. For details, go to www.vtechphones.com for online help topics.

Frequently asked questions

General product care

Storage

La plaque signalétique appliquée est située au bas du socle de

l’unité du bébé.

Lorsque vous utilisez votre appareil, vous devriez toujours suivre

certaines mesures de précaution de base aﬁn de réduire les risques

d’incendie, d’électrocution et de blessures corporelles, dont ceux

qui suivent:

1. Observez toutes les instructions et mises en garde inscrites sur

l’appareil.

2. L’installation par un adulte est requise.

3. MISE EN GARDE: N’installez pas l’unité du bébé à une hauteur

supérieure à 2 mètres.

4. Ce produit a été conçu pour être un dispositif d’appoint

seulement. Il n’est pas le remplacement d’une supervision

responsable et adéquate par un adulte et ne devrait pas être

utilisé comme telle.

5. Ce produit n’est pas conçu pour être utilisé en tant que moniteur

médical.

6. N’utilisez pas cet appareil près de l’eau ni de toute autre source

d’humidité, par exemple, près d’une baignoire, cuve à lessive,

évier de cuisine, dans un sous-sol humide ni près d’une piscine,

dans un soussol humide ou une douche.

7. MISE EN GARDE: N’utilisez que la pile fournie. Il peut y avoir

un risque d’explosion si un mauvais type de pile est utilisé

pour le dispositif apaisant. La pile ne peut pas être soumise

a des températures extrêmes élevées ou basses et a une

faible pression atmosphérique a haute altitude pendant son

utilisation, son entreposage ou son transport. Le fait de jeter

la pile dans au feu ou dans un four chaud, ou d’écraser ou de

couper mécaniquement la pile peut entrainer une explosion.

Le fait de laisser la pile dans un environnement a température

extrêmement élevée peut entrainer une explosion ou une

fuite de liquide ou de gaz inﬂammable. Une pile soumise a

une pression d’air extrêmement basse peut provoquer une

explosion ou une fuite de liquide ou de gaz inﬂammable.

Mettez au rebut la pile usagée conformément aux informations

ﬁgurant dans la section Le sceau RBRC.

8. N’utilisez que les adaptateurs inclus avec ce produit. L’utilisation

d’un adaptateur dont la polarité ou la tension serait inadéquate

risque d’endommager sérieusement le produit et mettre votre

sécurité en péril.

Informations sur les adaptateurs électriques :

Sortie : 5 V CC 1,5A

VTech Telecommunications Ltd.

Modèle : VT07EUS05150

Sortie : 5 V CC 2A

VTech Telecommunications Ltd.

Modèle : VT07EUS05200

Informations sur les piles rechargeables :

3,7V 5000mAh, 18,5Wh Lithium-ion batterie

Zhuhai Great Power Energy Co., Ltd.

Modèle : GSP806090-5Ah-3.7V-1S1P

9. Lorsqu’ils sont branchés dans une prise de courant, les

adaptateurs secteur ont été conçus pour être orientés

correctement, soit à la verticale ou au plancher. Les broches

n’ont pas été conçues pour supporter le poids du bloc

d’alimentation et le maintenir en place si celuici est branché dans

une prise au plafond, sous une table ou dans un meuble.

10. Pour les appareils raccordés, la prise de courant (de l’adaptateur

secteur) doit être installée près de l’équipement et doit être

facilement accessible.

11. Débranchez ce produit de la prise de courant avant de

procéder au nettoyage. N’utilisez pas de nettoyants en aérosols.

Utilisez un chiffon humide pour le nettoyer.

12. Ne coupez pas les cordons d’alimentation pour remplacer les

ﬁches, car ceci peut présenter un danger potentiel.

13. Ne laissez aucun objet reposer ni appuyer sur le cordon

d’alimentation. N’installez pas cet appareil dans un endroit où

l’on risque d’écraser le cordon d’alimentation ou de le piétiner.

14. Ne faites fonctionner cet appareil qu’avec le type d’alimentation

indiqué sur l’étiquette. Si vous ne connaissez pas le type

d’alimentation que vous possédez à votre domicile, consultez

votre marchand ou votre compagnie locale d’électricité.

15. Ne surchargez pas les prises de courant murales ni les rallonges

électriques.

16. Ne placez pas cet appareil sur un chariot, meuble, trépied,

support de montage ni table chancelants.

17. Les trous et ouvertures du boîtier, situés à l’arrière de l’appareil

ou sous celui-ci, servent à aérer l’appareil. Pour l’empêcher de

surchauffer, ne bloquez sous aucun prétexte ces ouvertures et

n’empêchez pas l’aération adéquate de l’appareil en le plaçant

sur un lit, divan, tapis ou toute autre surface similaire. De même,

ne le positionnez pas à proximité ni au-dessus d’une source de

chaleur ou d’un calorifère. De plus, ne placez pas l’appareil dans

un endroit avant de vous assurer qu’il y ait une bonne circulation

d’air.

18. N’enfoncez jamais d’objets à travers les ouvertures de cet

appareil, car ils pourraient entrer en contact avec des points de

tension dangereux ou causer des courts-circuits qui peuvent

dégénérer en incendies ou en risques d’électrocution. Ne

renversez jamais de liquide dans ce produit.

19. Aﬁn de réduire les risques d’électrocution, ne démontez pas cet

appareil, mais apportez-le dans un centre de service autorisé.

L’ouverture du boîtier ou le retrait de toutes pièces que contient

cet appareil, à l’exception de l’accès autorisé à certaines portes

ou ouvertures, risque de vous exposer à des points de tension

dangereux ou d’autres dangers. Un remontage incorrect peut

par la suite présenter des risques d’électrocution.

20. Vous devriez tester la réception chaque fois que vous mettez

l’appareil en fonction.

21. Examinez les composantes aﬁn de vériﬁer si celles-ci ne sont pas

endommagées.

22. Il existe un très faible risque de perte de conﬁdentialité

avec certains appareils électroniques (autres écoute-bébés,

téléphones sans ﬁls etc.). Pour l’éviter, s’assurer que le produit

n’a jamais été utilisé avant l’achat, réinitialiser l’unité de façon

périodique, éteindre l’écoute-bébé quand il n’est pas en cours

d’utilisation.

23. Les enfants devraient être supervisés aﬁn de vous assurer qu’ils

ne jouent pas avec l’appareil.

24. Les petites pièces de ce moniteur peuvent être avalées par les

bébés ou les petits enfants. Veuillez tenir ces pièces hors de

portée des enfants.

25. Le produit n’est pas conçu pour être utilisé par des personnes

(incluant des enfants) aux capacités physiques, sensorielles

ou mentales réduites ou qui manquent d’expérience et de

connaissances, à moins qu’on leur ait donné sufﬁsamment

de supervision ou d’instructions relativement à l’utilisation de

l’appareil par une personne responsable de leur sécurité.

CONSERVEZ CES INSTRUCTIONS

Mises en garde

• Utilisez et entreposez le produit à une température entre 0˚C

(32˚F) et 40˚C (104˚F).

• Risque de brûlure, risque d’incendie, risque d’explosion associé

à une mauvaise manipulation de la batterie.

• N’exposez pas cet appareil à des froids ou des chaleurs

extrêmes, ainsi qu’à la lumière directe du soleil. Ne l’installez pas

près d’une source de chauffage.

• Avertissement - Risque de strangulation -

Les enfants se sont ÉTRANGLÉS dans des cordons.

Gardez ce cordon hors de portée des enfants (à plus

de 0,9 m). N’enlevez pas cette étiquette.

• Ne jamais placer le moniteur à l’intérieur du berceau ou du parc

de bébé. Ne jamais couvrir le moniteur ou l’unité (s) portative

avec un article tel une serviette ou une couverture.

• D’autres produits électroniques peuvent causer des

interférences auprès de votre caméra IP. Essayez d’installer

votre caméra IP le plus loin possible de ces dispositifs

électroniques : routeurs sans ﬁl, radios, téléphones cellulaires,

interphones, moniteurs de pièces, téléviseurs, ordinateurs

personnels, appareils électriques de cuisine et téléphones

sans ﬁl.

Stimulateurs cardiaques implantés dans l’organisme

Les simulateurs cardiaques (ne s’applique qu’aux dispositifs

numériques sans ﬁl):

L’organisme ‘Wireless Technology Research, LLC (WTR)’, une

ﬁrme de recherche indépendante, a mené une évaluation

pluridisciplinaire des interférences entre les téléphones sans ﬁl

portatifs et les stimulateurs cardiaques implantés dans l’organisme.

Appuyée par l’Administration des aliments et drogues (FDA) des

États-Unis, la ﬁrme WTR recommande aux médecins:

Avis aux détenteurs de stimulateurs cardiaques

• Vous devriez maintenir les dispositifs sans ﬁl à au moins six

pouces du simulateur cardiaque.

• Ils ne doivent PAS placer le téléphone sans ﬁl directement sur

le stimulateur cardiaque, tel que dans une poche de chemise,

lorsque celui-ci est en marche.

L’étude effectuée par l’organisme WRS n’a pas identiﬁé de risque

pour les détenteurs de simulateurs cardiaques causés par les gens

qui utilisent dispositifs sans ﬁl à proximité de ceux-ci.

Champs électromagnétiques (EMF)

Ce produit de VTech est conforme à toutes les normes se rapportant

aux champs électromagnétiques (EMF) standard. Si vous le

manipulez correctement en suivant les instructions de ce guide, son

utilisation sera sécuritaire pendant de nombreuses années, selon les

meilleures évidences scientiﬁques dont nous disposons aujourd’hui.

For cETL compliance only

What does this limited warranty cover?

The manufacturer of this VTech Product warrants to the

holder of a valid proof of purchase (“Consumer” or “you”)

that the Product and all accessories provided in the sales

package (“Product”) are free from defects in material

and workmanship, pursuant to the following terms and

conditions, when installed and used normally and in

accordance with the Product operating instructions. This

limited warranty extends only to the Consumer for Products

purchased and used in the United States of America and

Canada.

What will VTech do if the Product is not free from defects

in materials and workmanship during the limited warranty

period (“Materially Defective Product”)?

During the limited warranty period, VTech’s authorized service

representative will replace at VTech’s option, without charge,

a Materially Defective Product. If we choose to replace

the Product, we may replace it with a new or refurbished

Product of the same or similar design. We will retain

defective parts, modules, or equipment. Replacement of the

Product, at VTech’s option, is your exclusive remedy. VTech

will return the replacement Products to you in working

condition. You should expect the replacement to take

approximately 30 days.

How long is the limited warranty period?

The limited warranty period for the Product extends for ONE

(1) YEAR from the date of purchase (90 days on products

purchased as Refurbished*). This limited warranty also

applies to the replacement Product for a period of either (a)

90 days from the date the replacement Product is shipped

to you or (b) the time remaining on the original one-year

warranty (90-day limited warranty on products that are

purchased as Refurbished*); whichever is longer.

*Refurbished products purchased from our online store

carry a 90-day replacement warranty.

What is not covered by this limited warranty?

This limited warranty does not cover:

1. Product that has been subjected to misuse, accident,

shipping or other physical damage, improper installation,

abnormal operation or handling, neglect, inundation, ﬁre,

water or other liquid intrusion; or

2. Product that has been damaged due to repair, alteration

or modiﬁcation by anyone other than an authorized

service representative of VTech; or

3. Product to the extent that the problem experienced is

caused by signal conditions, network reliability, or cable or

antenna systems; or

4. Product to the extent that the problem is caused by use

with non-VTech accessories; or

5. Product whose warranty/quality stickers, product serial

number plates or electronic serial numbers have been

removed, altered or rendered illegible; or

6. Product purchased, used, serviced, or shipped for repair

from outside the United States of America or Canada, or

used for commercial or institutional purposes (including

but not limited to Products used for rental purposes); or

7. Product returned without a valid proof of purchase (see

item 2 below); or

8. Charges for installation or set up, adjustment of customer

controls, and installation or repair of systems outside the

unit.

How do you get warranty service?

To obtain warranty service in the USA, please visit our

website at www.vtechphones.com or call 1 (800) 595-9511.

In Canada, go to www.vtechcanada.com or call

1 (800) 267-7377.

NOTE: Before calling for service, please review the user’s

manual - a check of the Product’s controls and features may

save you a service call.

Except as provided by applicable law, you assume the risk

of loss or damage during transit and transportation and are

responsible for delivery or handling charges incurred in the

transport of the Product(s) to the service location. VTech

will return replaced Product under this limited warranty.

Transportation, delivery or handling charges are prepaid.

VTech assumes no risk for damage or loss of the Product in

transit.

What must you return with the Product to get warranty

service?

1. Return the entire original package and contents including

the Product to the VTech service location along with a

description of the malfunction or difﬁculty; and

2. Include a “valid proof of purchase” (sales receipt)

identifying the Product purchased (Product model) and

the date of purchase or receipt; and

3. Provide your name, complete and correct mailing

address, and telephone number.

Other limitations

This warranty is the complete and exclusive agreement

between you and VTech. It supersedes all other written or

oral communications related to this Product. VTech provides

no other warranties for this Product. The warranty exclusively

describes all of VTech’s responsibilities regarding the Product.

There are no other express warranties. No one is authorized

to make modiﬁcations to this limited warranty and you should

not rely on any such modiﬁcation. State/Provincial Law Rights:

This warranty gives you speciﬁc legal rights, and you may also

have other rights, which vary from state to state or province

to province.

Limitations: Implied warranties, including those of ﬁtness

for a particular purpose and merchantability (an unwritten

warranty that the Product is ﬁt for ordinary use) are limited

to one year from the date of purchase. Some states/

provinces do not allow limitations on how long an implied

warranty lasts, so the above limitation may not apply to you.

In no event shall VTech be liable for any indirect, special,

incidental, consequential, or similar damages (including,

but not limited to lost proﬁts or revenue, inability to use

the Product or other associated equipment, the cost of

substitute equipment, and claims by third parties) resulting

from the use of this Product. Some states/provinces

do not allow the exclusion or limitation of incidental or

consequential damages, so the above limitation or exclusion

may not apply to you.

Please retain your original sales receipt as proof

of purchase.

Limited warranty

FCC and IC regulations

FCC Part 15

NOTE: This equipment has been tested and found to comply with the requirements for a Class B digital device under Part 15 of

the Federal Communications Commission (FCC) rules. These requirements are intended to provide reasonable protection against

harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio

or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

WARNING: Changes or modiﬁcations to this equipment not expressly approved by the party responsible for compliance could void

the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause

harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired

operation.

To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that can be safely absorbed by a

user or bystander according to the intended usage of the product. This product has been tested and found to comply with the FCC

criteria. The baby unit shall be installed and used such that parts of all persons’ body are maintained at a distance of approximately 8 in

(20 cm) or more. The transmitter and antenna of the parent unit shall be held at least 1 in (2.5 cm) from your face.

This Class B digital apparatus complies with Canadian requirement:

CAN ICES-3 (B)/NMB-3(B)

Industry Canada

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s

licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must

accept any interference, including interference that may cause undesired operation of the device.

The term ‘’IC:‘’ before the certiﬁcation/registration number only signiﬁes that the Industry Canada technical speciﬁcations were met.

This product meets the applicable Innovation, Science and Economic Development Canada technical speciﬁcations.

RF radiation exposure statement

The product complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The baby unit should be

installed and operated with a minimum distance of 8 in (20 cm) between the baby unit and all persons’ body. Use of other accessories

may not ensure compliance with FCC RF exposure guidelines. This equipment complies also with Industry Canada RSS-102 with respect

to Canada’s Health Code 6 for Exposure of Humans to RF Fields.

California Energy Commission battery

charging testing mode

This video monitor meets the California Energy Commission (CEC) regulations for energy consumption. Your video monitor is set up to

comply with the energy-conserving standards right out of the box.

Follow the instructions to install and charge the battery. The CEC battery charging testing mode is activated while charging.

Even if the parent unit is paired to camera units, the CEC battery charging testing mode is activated while it is powered off and

charging.

The RBRC seal on the lithium-ion battery indicates that VTech Communications, Inc. is voluntarily participating in an

industry program to collect and recycle these batteries at the end of their useful lives, when taken out of service within

the United States and Canada. The program provides a convenient alternative to placing used lithium-ion batteries into

the trash or municipal waste, which may be illegal in your area.

VTech’s participation makes it easy for you to drop off the spent product at local retailers participating in the program

or at authorized VTech product service centers. Please call 1 (800) 8 BATTERY® for information on Li-ion battery recycling and disposal

bans/restrictions in your area. VTech’s involvement in this program is part of its commitment to protecting our environment and

conserving natural resources.

The RBRC Seal and 1 (800) 8 BATTERY® are registered trademarks of Call2recycle, Inc.

The RBRC seal

To ensure that your HD video monitor is always at its best performance, the Parent Unit

will prompt a message and ask you to update its software and the Baby Unit’s ﬁrmware

when there are new versions available. Select “Now” to reboot the system, or switch off

and on the Parent Unit later to reboot the system into the latest software.

• To check if your device is running on the latest software, or to update your device

software, go to:

> > Software Update.

Connect your HD video monitor with home Wi-Fi network

You must connect your video monitor to your secured home Wi-Fi network in order to

receive the latest software and ﬁrmware updates. To set the Wi-Fi up, go to:

> > Congure Wi-Fi.

• Make sure the Baby Unit is on when you set up the Wi-Fi network.

Auto software and rmware update

Basic operation

Talk to your baby via the baby unit

1. Press and hold the TALK key.

2. When the icon displays on

screen, speak to your parent unit.

Your voice is transmitted to the

baby unit.

3. When ﬁnished talking, release

the TALK key to hear your baby

again.

Zoom

Press to zoom in or out in a ﬁxed zoom

sequence. indicates the image is

magniﬁed 2 times.

Adjust speaker volume

Press | to adjust the parent unit

speaker volume level received from the

baby unit.

After powering up your baby monitor, the parent unit streams live video in direct mode.

We recommend you follow the instructions on-screen to set up home Wi-Fi network

with your monitor for functionality enhancements and mobile access. See Auto software

and rmware update and Download app for mobile access in this Quick Start Guide.

Use the menu

Press MENU on the parent unit to enter the

main menu, choose a menu item, or save a

setting. You can use the parent unit menu

for advanced settings or operations, such

as to play or stop the baby unit lullaby, or

adjust the baby unit sound sensitivity.

While in the menu:

• Press | | | to scroll through the

menu options.

• Press SELECT to select an item.

• Press TALK to return to the live video.

• Press to go to the Help & info page.

To restore to the default settings or reset the

Wi-Fi connection, you can reset the parent unit

by pressing the RESET key at the back of the unit.

Insert a pin into the RESET hole on the back of

the parent unit, and then gently press the button

inside.

Turn on/off the parent unit screen

You can turn on or turn off the parent unit

screen without powering off the unit. You

will still hear sounds from the baby unit.

• Press | LCD ON/OFF on the parent unit

to turn off the screen.

• Press any key on the parent unit to turn

the screen on again.

Muted

Press and hold

VTech cares about your privacy and peace of mind. That’s why we’ve put together a list of industry-

recommended best practices to help keep your wireless connection private and your devices protected when

online. We recommend you carefully review and consider complying with the following tips.

Ensure your wireless connection is secure.

• Before installing a device, ensure your router’s wireless signal is encrypted by selecting the “WPA2-PSK

with AES” setting in your router’s wireless security menu.

Change default settings.

• Change your wireless router’s default wireless network name (SSID) to something unique.

• Change default passwords to unique, strong passwords. A strong password:

- Is at least 10 characters long.

- Is complex.

- Does not contain dictionary words or personal information.

- Contains a mix of uppercase letters, lowercase letters, special characters and numbers.

Keep your devices up to date.

• Download security patches from manufacturers as soon as they become available. This will ensure you

always have the latest security updates.

• If the feature is available, enable automatic updates for future releases.

Disable Universal Plug and Play (UPnP) on your router.

• UPnP enabled on a router can limit the effectiveness of your ﬁrewall by allowing other network devices

to open inbound ports without any intervention or approval from you. A virus or other malware program

could use this function to compromise security for the entire network.

For more information on wireless connections and protecting your data, please review the following

resources from industry experts:

1. Federal Communications Commission: Wireless Connections and Bluetooth Security Tips –

www.fcc.gov/consumers/guides/how-protect-yourself-online.

2. U.S. Department of Homeland Security: Before You Connect a New Computer to the Internet –

www.us-cert.gov/ncas/tips/ST15-003.

3. Federal Trade Commission: Using IP Cameras Safely –

https://www.consumer.ftc.gov/articles/0382-using-ip-cameras-safely.

4. Wi-Fi Alliance: Discover Wi-Fi Security –

http://www.wi-ﬁ.org/discover-wi-ﬁ/security.

Protect your privacy and online security

Need help?

Use your smartphone or mobile device to access our online help.

• Go to https://help.vtechphones.com/VC2105; OR

• Scan the QR code on the right. Launch the camera app or

QR code scanner app on your smartphone or tablet. Hold

the device’s camera up to the QR code and frame it. Tap

the notiﬁcation to trigger the redirection of the online help.

- If the QR code is not clearly displayed, adjust your

camera’s focus by moving your device closer or

further away until it is clear.

If you would like to contact us, visit

https://help.vtechphones.com/cs.

You can also call our Customer Support at 1-844-848-

8324 (1-844-84-VTECH) [in US] or 1-888-211-2005 [in

Canada] for help.

Driven by system updates, the software, online help topics, and online FAQs

will be updated periodically.

For operations and guides to help you using your HD video monitor, and for

latest information and supports, go and check the online help topics and online

FAQs.

VC2105

CABLE MANAGEMENT

1 2 3

Direct mode

Your baby monitor parent unit and baby unit connect to each other in Direct mode by default,

which allows you to immediately stream video out of the box.

It is NOT recommended to continue using Direct Mode connection after initial installation.

You may experience reduced signal

strength if your parent unit and baby unit

are far apart, or there are obstructing

factors, such as internal walls, between

them. Move the parent unit closer to the

baby unit to improve the signal strength.

Router mode

You are required to set up your

monitor in Router mode to enjoy live

video streaming via your parent unit

with an enhanced connection. Router

mode is the recommended mode for

stable connectivity.

Router mode uses your home Wi-

Fi network to connect your video

monitor. It supports live video

streaming through the parent unit and

smartphone app.

If you want to stream live video

remotely with your mobile device,

download and install the MyVTech

Baby Plus mobile app. With the

mobile app, your Wi-Fi router (not included) provides Internet connectivity to your HD video

monitor system. It serves as a communicating channel between your baby unit and mobile

device, allowing you to monitor and/or control your baby unit wherever you are. For more

details, see Download app for mobile access section in this quick start guide.

• When both parent unit and app are viewing the camera simultaneously,

the video quality will be optimised to deliver the best possible viewing result.

How the system works

For better security and more stable connectivity, this baby monitor requires

connecting to a Wi-Fi network and operating in Router mode connection.

Local access

Local access, for

start up quick view

and setup stage.

Mobile access

Connecting Wi-Fi to

enhance local access

Connect, charge and power on the parent unit

Charge the parent unit battery before use

The parent unit runs on an internal rechargeable battery or AC power. To continuously monitor

your baby, keep the parent unit connected to AC power.

• Before using the baby monitor for the ﬁrst time,

charge the parent unit battery for 12 hours. When

the parent unit battery is fully charged, the battery

icon segments are solid .

• The standby time varies depending on your actual

use.

The parent unit turns on automatically after

connecting to the power socket, and the

welcome screen appears. You can press Power

to turn the parent unit on or press and hold to

turn it off.

Connect the baby monitor

• The rechargeable battery in the parent unit is built-in.

• Use only the power adapters supplied with this product.

• Make sure the parent unit and the baby unit are not connected to an electronically controlled electric

outlet.

• Connect the power adapters in a vertical or ﬂoor mount position only. The adapter prongs are not

designed to hold the weight of the parent unit and the baby unit, so do not connect them to any ceiling,

under-the-table, or cabinet outlets. Otherwise, the adapter may not properly connect to the outlets.

• Make sure the parent unit, the baby unit and the power adapter cords are out of reach of children.

Raise the parent unit

antenna for better

reception

The battery icon indicates the battery status (see the following table).

Battery indicators Battery status Action

and are displayed on

the screen;

The red LED light ﬂashes.

The battery has very little

charge and may be used

for only a short time.

Charge

without interruption

(about 30 minutes).

The battery icon segments are

solid .

The battery is fully

charged. To keep the battery charged,

connect it to AC power

when in use.

Parent unit icons

Main

Sub-

menu Options

Night light

• Turn on or turn off night

light.

• Select a night light color.

• Adjust night light

brightness.

• Set the brightness to

Auto adaptive ambience.

• Set the timer to turn off

night light after 15, 30 or

60 minutes, or remain on

always.

Melodies and soothing sounds

• Play or stop.

• Select to play all

melodies, or play one of

the ﬁve melodies or ﬁve

soothing sounds.

• Set the timer to stop

playing after 15, 30 or 60

minutes, or play non-stop.

• Adjust the play volume

level.

General settings

• Connect to home Wi-Fi

network.

• Connect mobile phone.

• Adjust Baby Unit speaker

volume.

• Adjust Parent Unit screen

brightness.

• Turn the screen off timer

on/off, set to screen off

after 1, 3 or 5 minutes,

or auto screen on when

sound detected.

• Set Sound Sensitivity

Level for auto screen on.

Main

Sub-

menu Options

• Change temperature

display format.

• Mute or adjust

notiﬁcations volume

level.

• Turn on/off low battery

notiﬁcation.

• Turn on/off no link

notiﬁcation.

• Reset settings, software

update.

Alerts Settings

• Adjust alerts volume

level.

• Select maximum and

minimum temperature

for alert range;

• Turn on/off temperature

detection alert.

• Adjust Motion Sensitivity

Level to activate parent

unit screen and speaker.

• Turn on/off motion

detection alert.

• Turn on/off cry alert.

• Turn on/off face covered

alert.

Help and info

• Support Information

• System Information

Status icons

Melodies and soothing sounds are

playing.

Night light is turned on.

Auto night light brightness is activated.

Temperature alert is turned on.

Parent unit is muted.

Humidity

Temperature

Battery level indicator

Low battery indicator

Status icons

Direct mode

The parent unit and baby unit

connect to each other directly.

Red bars indicate no connection.

Router mode

The parent unit and baby unit

connect via the home Wi-Fi network.

The red icon(s) on the baby unit or

parent unit, indicates no connection

between the respective unit(s) and

the router.

Night vision is turned on.

Motion detection alert is turned on.

Cry alert is turned on.

Face covered alert is turned on.

VTech VC2105 Mode d'emploi

Marque: VTech

Modèle: VC2105

Catégorie: Moniteurs vidéo bébé

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: VTech VC2105 User guide

VTech VC2105 Mode d'emploi

VTech VC2105 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents