Moog FCH360C8WY Mode d'emploi

Marque: Moog

Modèle: FCH360C8WY

Catégorie: Boîtiers de caméra

Taper: Mode d'emploi

Ce manuel convient également à

www.moogvideolarm.com

F C H 3 6 0

Fusion Camera Housing with Panomorph Lens Options

Installation and Operation Instructions for the following models:

FCH360CW Environmental housing with feed-thru wall/pole mount with 360 viewing window

FCH360C2W Environmental housing with feed-thru wall/pole mount, 24Vac or 12Vdc input,

360 viewing window, heater & blower

FCH360C2WY Environmental housing with feed-thru wall/pole mount, 24Vac or 12Vdc input,

heater & blower, 360 viewing window, adjustable sunshield

FCH360C8WY Environmental housing with feed-thru wall/pole mount, dynamic power allocation

PoE input, 30 watt midspan included, heater & blower, supports .at PoE cameras,

360 viewing window, adjustable sunshield

Before attempting to connect or operate this product, please read these instructions completely.

81-IN5507

01-18-2013

IMPORTANT SAFEGUARDS SAFETY PRECAUTIONS

UNPACKING

SERVICE

1 Read these instructions.

2 Keep these instructions.

3 Heed all warnings

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with damp cloth.

7 Do not block any of the ventilation openings. Install in accordance with the

manufacturers instructions.

8 Cable Runs- All cable runs must be within permissible distance.

9 Mounting - This unit must be properly and securely mounted to a supporting

structure capable of sustaining the weight of the unit.

Accordingly:

a. This installation should be made by a qualied service person and should conform

to all local codes.

b. Care should be exercised to select suitable hardware to install the unit, taking into

account both the composition of the mounting surface and the weight of the unit.

10 Do not install near any heat sources such as radiators, heat registers, stoves, or other

apparatus ( including ampliers) that produce heat.

11 Do not defeat the safety purpose of the polarized or grounding-type plug. A

polarized plug has two blades with one wider than the other. A grounding type

plug has two blades and a third grounding prong. The wide blade or the third

prong are provided for your safety. When the provided plug does not t into your

outlet, consult an electrician for replacement of the obsolete outlet.

12 Protect the power cord from being walked on or pinched particularly at plugs,

convenience receptacles, and the point where they exit from the apparatus.

13 Only use attachment/ accessories specied by the manufacturer.

14 Use only with a cart, stand, tripod, bracket, or table specied by the manufacturer,

or sold with the apparatus. When a cart is used, use caution when moving the cart/

apparatus combination to avoid injury from tip-over.

15 Unplug this apparatus during lighting storms or when unused for long periods of time.

16 Refer all servicing to qualied service personnel. Servicing is required when the

apparatus has been damaged in any way, such as power-supply cord or plug is

damaged, liquid has been spilled of objects have fallen into the apparatus, the

apparatus has been exposed to rain or moisture, does not operate normally, or

has been dropped.

Be sure to periodically examine the unit and the supporting structure to make sure that the integrity

of the installation is intact. Failure to comply with the foregoing could result in the unit separating

from the support structure and falling, with resultant damages or injury to anyone or anything struck

by the falling unit.

Unpack carefully. Electronic components can be

damaged if improperly handled or dropped. If an item

appears to have been damaged in shipment, replace

it properly in its carton and notify the shipper.

Be sure to save:

1 The shipping carton and packaging material.

They are the safest material in which to make future

shipments of the equipment.

2 These Installation and Operating Instructions.

If technical support or service is needed, contact us at

the following number:

The lightning ash with an arrowhead symbol,

within an equilateral triangle, is intended to

alert the user to the presence of non-insulated

“dangerous voltage” within the product’s

enclosure that may be of sufcient magnitude

to constitute a risk to persons.

Este símbolo se piensa para alertar al usuario a la presencia

del “voltaje peligroso no-aisIado” dentro del recinto de los

productos que puede ser un riesgo de choque eléctrico.

Ce symbole est prévu pour alerter I’utilisateur à la presence

“de la tension dangereuse” non-isolée dans la clôture de

produits qui peut être un risque de choc électrique.

Dieses Symbol soll den Benutzer zum Vorhandensein der

nicht-lsolier “Gefährdungsspannung” innerhalb der

Produkteinschließung alarmieren die eine Gefahr des

elektrischen Schlages sein kann.

Este símbolo é pretendido alertar o usuário à presença “di

tensão perigosa non-isolada” dentro do cerco dos produtos

que pode ser um risco de choque elétrico.

Questo simbolo è inteso per avvertire I’utente alla presenza

“di tensione pericolosa” non-isolata all’interno della

recinzione dei prodotti che può essere un rischio di scossa

elettrica

The exclamation point within an equilateral

triangle is intended to alert the user to

presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the appliance.

Este símbolo del punto del exclamation se piensa para

alertar al usuario a la presencia de instrucciones importantes

en la literatura que acompaña la aplicación.

Ce symbole de point d’exclamation est prévu pour alerter

l’utilisateur à la presence des instructions importantes dans

la littérature accompagnant l’appareil.

Dieses Ausruf Punktsymbol soll den Benutzer zum

Vorhandensein de wichtigen Anweisungen in der Literatur

alarmieren, die das Gerät begleitet.

Este símbolo do ponto do exclamation é pretendido alertar o

usuário à presença de instruções importantes na literatura

que acompanha o dispositivo.

Questo simbolo del punto del exclamaton è inteso per

avvertire l’utente alla presenza delle istruzioni importanti nella

letteratura che accompagna l'apparecchio.

TECHNICAL SUPPORT

AVAILABLE 24 HOURS

1- 800 - 554 -1124

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER ( OR BACK). NO USER- SERVICE-

ABLE PARTS INSIDE. REFER SEVICING

TO QUALIFIED SERVICE PERSONNEL.

Limited Warranty for Moog Videolarm Products

Moog Videolarm warrants these products to be free from defects in material or workmanship as follows:

PRODUCT CATEGORY PARTS \ LABOR

All Enclosures and Electronics* Five (5) Years

Poles/PolEvators™/CamEvator Three (3) Years

Warrior Series™/Q-View™/IR Illuminators Five (5) Years

SView Series™ Five (5) Years **6 months if used in auto scan/tour operation

Controllers Five (5) Years

Power Supplies Five (5) Years

EcoKit Three (3) Years

Accessory Brackets Five (5) Years

Liberty Dome Three (3) Years

*DeputyDome™, NiteTrac™, Igloo Dome, PurgeDome™ Three (3) Years **6 months if used in auto scan/tour operation

During the labor warranty period, to repair the Product, Purchaser will either return the defective product, freight prepaid, or deliver it to Moog Videolarm

Inc. Decatur GA. The Product to be repaired is to be returned in either its original carton or a similar package affording an equal degree of protection with

a RMA # (Return Materials Authorization number) displayed on the outer box or packing slip. To obtain a RMA# you must contact our Technical Support

Team at 800.554.1124, extension 101. Moog Videolarm will return the repaired Product freight prepaid to Purchaser. Moog Videolarm is not obligated to

provide Purchaser with a substitute unit during the warranty period or at any time. After the applicable warranty period, Purchaser must pay all labor and/or

parts charges.

The limited warranty stated in these product instructions is subject to all of the following terms and conditions.

TERMS AND CONDITIONS

1. NOTIFICATION OF CLAIMS: WARRANTY SERVICE: If Purchaser believes that the Product is defective in material or workmanship, then written notice with an

explanation of the claim shall be given promptly by Purchaser to Moog Videolarm. All claims for warranty service must be made within the warranty period.

If after investigation Moog Videolarm determines the reported problem was not covered by the warranty, Purchaser shall pay Moog Videolarm for the cost of

investigating the problem at its then prevailing per incident billable rate. No repair or replacement of any Product or part thereof shall extend the warranty period

of the entire Product. The speci c warranty on the repaired part only shall be in effect for a period of ninety (90) days following the repair or replacement of that

part or the remaining period of the Product parts warranty, whichever is greater.

2. EXCLUSIVE REMEDY: ACCEPTANCE: Purchaser’s exclusive remedy and Moog Videolarm’s sole obligation is to supply (or pay for) all labor necessary to repair any

Product found to be defective within the warranty period and to supply, at no extra charge, new or rebuilt replacements for defective parts.

3. EXCEPTIONS TO LIMITED WARRANTY: Moog Videolarm shall have no liability or obligation to Purchaser with respect to any Product requiring service during the

warranty period which is subjected to any of the following: abuse, improper use, negligence, accident, lightning damage or other acts of God (i.e., hurricanes,

earthquakes), modi cation, failure of the end-user to follow the directions outlined in the product instructions, failure of the end-user to follow the maintenance

procedures recommended by the International Security Industry Organization, written in product instructions, or recommended in the service manual for the

Product. Furthermore, Moog Videolarm shall have no liability where a schedule is speci ed for regular replacement or maintenance or cleaning of certain parts

(based on usage) and the end-user has failed to follow such schedule; attempted repair by non-quali ed personnel; operation of the Product outside of the

published environmental and electrical parameters, or if such Product’s original identi cation (trademark, serial number) markings have been defaced, altered,

or removed. Moog Videolarm excludes from warranty coverage Products sold AS IS and/or WITH ALL FAULTS and excludes used Products which have not

been sold by Moog Videolarm to the Purchaser. All software and accompanying documentation furnished with, or as part of the Product is furnished “AS IS”

(i.e., without any warranty of any kind), except where expressly provided otherwise in any documentation or license agreement furnished with the Product. Any

cost associated with removal of defective product and installation of replacement product is not included in this warranty.

4. PROOF OF PURCHASE: The Purchaser’s dated bill of sale must be retained as evidence of the date of purchase and to establish warranty eligibility.

DISCLAIMER OF WARRANTY

EXCEPT FOR THE FOREGOING WARRANTIES, Moog Videolarm HEREBY DISCLAIMS AND EXCLUDES ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,

INCLUDING, BUT NOT LIMITED TO ANY AND/OR ALL IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND/OR

ANY WARRANTY WITH REGARD TO ANY CLAIM OF INFRINGEMENT THAT MAY BE PROVIDED IN SECTION 2-312(3) OF THE UNIFORM COMMERCIAL

CODE AND/OR IN ANY OTHER COMPARABLE STATE STATUTE. Moog Videolarm HEREBY DISCLAIMS ANY REPRESENTATIONS OR WARRANTY THAT

THE PRODUCT IS COMPATIBLE WITH ANY COMBINATION OF NON-Moog Videolarm PRODUCTS OR NON-Moog Videolarm RECOMMENDED PRODUCTS

PURCHASER MAY CHOOSE TO CONNECT TO THE PRODUCT.

LIMITATION OF LIABILITY

THE LIABILITY OF Moog Videolarm, IF ANY, AND PURCHASER’S SOLE AND EXCLUSIVE REMEDY FOR DAMAGES FOR ANY CLAIM OF ANY KIND

WHATSOEVER, REGARDLESS OF THE LEGAL THEORY AND WHETHER ARISING IN TORT OR CONTRACT, SHALL NOT BE GREATER THAN THE ACTUAL

PURCHASE PRICE OF THE PRODUCT WITH RESPECT TO WHICH SUCH CLAIM IS MADE. IN NO EVENT SHALL Moog Videolarm BE LIABLE TO PURCHASER

FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO, COMPENSATION,

REIMBURSEMENT OR DAMAGES ON ACCOUNT OF THE LOSS OF PRESENT OR PROSPECTIVE PROFITS OR FOR ANY OTHER REASON WHATSOEVER.

Contents of Box

24Vac: 17 watts Heater (16 watts), Blower (1 watt)

12Vdc: 7 watts Heater (6 watts), Blower (1 watt)

PoE: IEEE802.at

Camera Power:

Tools Required: .100” Flat head screwdriver

Phillips head screwdriver

24Vac: 17 vatios Calentador (16 vatios), soplador (1 vatio)

12Vdc: 7 vatios Calentador (6 vatios), soplador (1 vatio)

PoE: IEEE802.at

Energía de la cámara:

Herramientas requeridas: .100” destornillador principal plano

Destornillador principal Phillips

24Vac: 17 watts Réchauffeur (16 watts), ventilateur (1 watt)

12Vdc: 7 watts Réchauffeur (6 watts), ventilateur (1 watt)

PoE : IEEE802.at

Puissance d'appareil-photo:

Outils requis : .100 » tournevis principal plat Tournevis phillips

24Vac: 17 Watt Heizung (16 Watt), Gebläse (1 Watt)

12Vdc: 7 Watt Heizung (6 Watt), Gebläse (1 Watt)

PoE: IEEE802.at

Kamera-Energie:

Werkzeuge erfordert: .100“ acher Hauptschraubenzieher

Kreuzkopfschraubenzieher

24Vac: 17 watts Calefator (16 watts), ventilador (1 watt)

12Vdc: 7 watts Calefator (6 watts), ventilador (1 watt)

Ponto de entrada: IEEE802.at

Ferramentas exigidas: .100” chave de fenda principal lisa Chave de

fenda principal de Phillips

24Vac: 17 watt Riscaldatore (16 watt), ventilatore (1 watt)

12Vdc: 7 watt Riscaldatore (6 watt), ventilatore (1 watt)

PoE: IEEE802.at

Potere della macchina fotograca:

Gli attrezzi hanno richiesto: .100„ cacciaviti capi piani Cacciavite phillips

FCH360C2W / FCH360C2WY / FCH360C8WY

FCH360CW

OUTDOOR and PoE MODELS:

Indoor Model:

No Electronics

Ninguna electrónica

Aucune électronique

Keine Elektronik

Nenhuma eletrônica

Nessun'elettronica

Français

FCH360 Series

Electrical Specifications

Power 24Vac / 12Vdc

Class 2 Only

Deutsch

Italiano

Portuguese

Español

English

Français

Deutsch

Italiano

Portuguese

Español

English

If you are running a conduit to the housing, rst

install the appropriate tting to the wall mount.

• Si usted está funcionando con un conducto a la cubierta, primero instale

la guarnición apropiada al montaje de la pared.

• Si vous courez un conduit au logement, installez d'abord l'ajustage de

précision approprié sur le bâti de mur.

• Wenn Sie ein Rohr zum Gehäuse laufen lassen, bringen Sie zuerst die

passende Befestigung zur Wandeinfassung an.

• Se você está funcionando uma canalização à carcaça, instale

primeiramente o encaixe apropriado à montagem da parede.

• Se stiate facendo funzionare un condotto all'alloggiamento, in primo

luogo installi il montaggio adatto al supporto della parete.

Attach mount to wall with suitable hardware

(not provided).

• Ate el montaje a la pared con el hardware conveniente

(no proporcionado).

• Attachez le bâti au mur avec le matériel approprié (non fourni).

• Bringen Sie Einfassung zur Wand mit der verwendbaren Hardware an

(nicht bereitgestellt).

• Una a montagem à parede com a ferragem apropriada (não fornecida).

• Attacchi il supporto alla parete con ssaggi adatti (non forniti).

WALL MOUNTING

If attaching to pole, rst break away tabs with pliers and

remove (4) strap plugs.

• Si atan al poste, el primeros rompen lejos lengüetas con los alicates

y quitan (4) los enchufes de la correa.

• Si attachant au poteau, les premiers cassent loin des étiquettes avec

des pinces et enlèvent (4) des prises de courroie.

• Bei der Befestigung zum Pfosten, brechen erste weg Vorsprünge mit

Zangen und entfernen (4) Bügelstecker.

• Se unindo ao pólo, o primeiros quebram afastado abas com alicates

e removem (4) plugues da cinta.

• Se attaccando al palo, i primi rompono via le linguette con le pinze e

rimuovono (4) la cinghia tappa.

TAB

POLE MOUNTING

N O T E : T H E F O L L O W I N G I N S T R U C T I O N S M A I N LY S H O W T H E F C H 3 6 0 C W,

B U T T H E S E I N S T R U C T I O N S A R E A P P L I C A B L E T O A L L F C H 3 6 0 M O D E L S .

Lossen and then rotate the wall mount to achieve the

proper orientation.

• Aoje y gire el soporte de pared para conseguir la orientación adecuada.

• Desserrer et puis tourner le support mural pour atteindre le bon sens.

• Lösen und drehen Sie dann die Wandhalterung, um die richtige

Ausrichtung zu erreichen.

• Solte e, em seguida, gire o suporte de parede para alcançar a

orientação adequada.

• Allentare e quindi ruotare il supporto a parete per raggiungere il

corretto orientamento.

Twist

Rotate

Recommended Hardware for the Mounting Holes: • 5/16” - 18 (or M8 for metric) x minimum 1 ¼” Hex Head Bolt • 5/16” Flat Washer

• 5/16” Lock Washer

Hinge housing away from mount by loosening (2)

rear screws.

• Abisagre la cubierta lejos del montaje aojando (2) los tornillos

posteriores.

• Articulez le logement à partir du bâti en desserrant (2) les vis arrière.

• Lagern Sie Gehäuse weg von Einfassung schwenkbar, indem Sie (2)

hintere Schrauben lösen.

• Articule a carcaça longe da montagem afrouxando (2) os parafusos

traseiros.

• Alloggiamento della cerniera a partire dal supporto allentando (2) viti

posteriori.

Attach mount to pole with suitable hardware

(not provided).

• Ate el montaje al poste con el hardware conveniente (no proporcionado).

• Attachez le bâti au poteau avec le matériel approprié (non fourni).

• Bringen Sie Einfassung zum Pfosten mit der verwendbaren Hardware an

(nicht bereitgestellt).

• Una a montagem ao pólo com a ferragem apropriada (não fornecida).

• Attacchi il supporto al palo con ssaggi adatti (non forniti).

TAB

* Max Strap Width: 0.75”

Run cables through mount either by conduit input or through the back of the mount.

• Funcione con los cables montan a través por el conducto entrado o a través de la parte posterior del montaje.

• Courez les câbles montent à travers par le conduit entré ou par le dos du bâti.

• Laufen lassen Sie Kabel anbringen durch entweder durch das eingegebene Rohr oder durch die Rückseite der Einfassung.

• Funcione cabos montam completamente pela canalização entrada ou através da parte traseira da montagem.

• Faccia funzionare i cavi attraverso montano dal condotto immesso o tramite la parte posteriore del supporto.

Pass cables through wiring membranes

(use screwdriver to pierce).

• Pase los cables a través de las membranas del cableado

(el destornillador del uso a perforar) .

• Passez les câbles par des membranes de câblage

(le tournevis d'utilisation à percer).

• Führen Sie Kabel durch Verdrahtungsmembranen

(zu durchbohren der Gebrauchschraubenzieher) .

• Passe cabos através das membranas da ação

(a chave de fenda do uso a perfurar).

• Passi i cavi tramite le membrane dei collegamenti

(cacciavite di uso da perforare).

Hinge the housing closed and tighten (2) rear screws.

• Abisagre la cubierta cerrada y apriete (2) los tornillos posteriores.

• Articulez le logement fermé et serrez (2) les vis arrière.

• Lagern Sie das geschlossene Gehäuse schwenkbar und ziehen Sie

(2) hintere Schrauben fest.

• Articule a carcaça fechado e aperte (2) os parafusos traseiros.

• Munisca l'alloggiamento di cardini chiuso e stringa (2) viti posteriori.

Open housing lid.

• Abra la tapa de la cubierta.

• Ouvrez le couvercle de logement.

• Öffnen Sie Gehäusekappe.

• Abra a tampa da carcaça.

• Apra il coperchio dell'alloggiamento.

Remove camera tray by squeezing tabs together.

• Quite la bandeja de la cámara exprimiendo lengüetas juntas.

• Enlevez le plateau d'appareil-photo en serrant des étiquettes ensemble.

• Entfernen Sie Kamerabehälter, indem Sie zusammen Vorsprünge

zusammendrücken.

• Remova a bandeja da câmera espremendo abas junto.

• Rimuova insieme il vassoio della macchina fotograca comprimendo le

linguette.

TAB

Mount camera with ¼-20 hardware. Position the lens as shown and center with the spacers as needed, conrm

tabs are securely snapped into place. NOTE: Take care not to scratch dome with lens case.

• Monte la cámara con ¼ -20 hardware. Coloque el lente como se muestra y centro con los espaciadores según sea necesario,

conrmar pestañas estén bien encajados. NOTA: Tenga cuidado de no rayar cúpula con estuche.

• Montage de la caméra avec ¼ -20 matériel. Positionnez l'objectif dans le centre et avec les entretoises au besoin,

conrmer onglets sont correctement enclenché. REMARQUE: Veillez à ne pas rayer dôme avec étui à lentilles.

• Mount Kamera mit ¼ -20 Hardware. Positionieren Sie das Objektiv wie abgebildet und in der Mitte mit den Abstandshaltern wie nötig,

werden sicher einrastet bestätigen Registerkarten. HINWEIS: Achten Sie darauf, Kuppel mit Linsenbehälter kratzen.

• Suporte de câmera com ¼ de hardware -20. Posicione a lente como mostrado e centro com os espaçadores, conforme necessário,

conrme guias são bem encaixada no lugar. NOTA: Tome cuidado para não arranhar cúpula com lente caso.

• Montare con fotocamera ¼ -20 hardware. Posizionare la lente come mostrato e centro con i distanziali, se necessario,

vericare le schede siano correttamente scattati in posizione. NOTA: Fare attenzione a non grafare cupola con portalenti.

- ALIGN LENS -

Spacer

- TOP VIEW-

Detail

INPUT POWER CAMERA POWER GO TO

⇒

24Vac ⇒ 24Vac ⇒ SECTION A

⇒ 12Vdc ⇒ 12Vdc ⇒ SECTION B

⇒ 24Vac ⇒ 12Vdc ⇒ SECTION C

⇒ PoE (30W) ⇒ PoE (30W) ⇒ SECTION D

- Terminate incoming voltage as shown.

- Install shunts on “12Vdc” jumpers as shown.

- Power output to camera will be 12Vdc.

• Termine el voltaje entrante como se muestra.

- Instale la desviación en el puente “12Vdc” como se muestra.

- La salida de energía a la cámara será 12Vdc.

• Terminez la tension entrante comme montrée.

- Installez le shunt sur le pullover « 12Vdc » comme montré.

- Le rendement de puissance à l'appareil-photo sera 12Vdc.

• Beenden Sie ankommende Spannung wie gezeigt.

- Bringen Sie Shunt auf Überbrücker „12Vdc“ wie gezeigt an.

- Abgabeleistung zur Kamera ist 12Vdc.

• Termine a tensão entrante como mostrada.

- Instale a derivação na ligação em ponte “12Vdc” como

mostrada.

- A saída de poder à câmera será 12Vdc.

• Termini la tensione ricevuta come indicata.

- Installi lo shunt sul ponticello “12Vdc„ come indicato.

- L'output di forza motrice alla macchina fotograca sarà 12Vdc.

SHUNTS

- Terminate power and data lines.

- Install shunts on “24Vac” jumpers as shown.

- Power output to camera will be 24Vac.

• Termine las líneas de la energía y de datos.

- Instale la desviación en el puente “24Vac” como se muestra.

- La salida de energía a la cámara será 24Vac.

• Terminez les lignes de puissance et de données.

- Installez le shunt sur le pullover « 24Vac » comme montré.

- Le rendement de puissance à l'appareil-photo sera 24Vac.

• Beenden Sie Energie und Datenleitungen.

- Bringen Sie Shunt auf Überbrücker „24Vac“ wie gezeigt an.

- Abgabeleistung zur Kamera ist 24Vac.

• Termine linhas do poder e de dados.

- Instale a derivação na ligação em ponte “24Vac” como

mostrada.

- A saída de poder à câmera será 24Vac.

• Termini le linee di dati e di potere.

- Installi lo shunt sul ponticello “24Vac„ come indicato.

- L'output di forza motrice alla macchina fotograca sarà 24Vac.

SHUNTS

SECTION A: 24Vac Input for 24Vac Camera

SECTION B: 12Vdc Input for 12Vdc Camera

NOTE:

To maximize power for the camera and heater option, the unit

requires that you calibrate the enclosure. During calibration,

the onboard processor intelligently determines the maximum

safe power output of the midspan, and ensures that the

enclosure does not exceed that limit. Once calibration is

complete the required values are stored in permanent

memory, with no additional calibration required.

• Para maximizar la potencia de la opción de cámara y la calefacción, la unidad requiere

que calibre la caja. Durante la calibración, el procesador de a bordo determina de forma

inteligente la potencia máxima seguridad del centro de la luz, y asegura que el recinto no

exceda de ese límite. Una vez que la calibración se ha completado los valores requeridos

se almacenan en la memoria permanente, sin calibración adicional.

• Pour maximiser la puissance de l'option appareil photo et le chauffage, l'unité exige

que vous calibrer l'enceinte. Lors de l'étalonnage, le processeur embarqué détermine

intelligemment la puissance de sortie maximale de sécurité de l'injecteur, et veille à ce

que l'enceinte ne dépasse pas cette limite. Une fois l'étalonnage est terminé, les valeurs

requises sont stockées dans la mémoire permanente, sans étalonnage supplémentaire

n'est nécessaire.

• Um Strom für die Kamera und Heizung Option zu maximieren, setzt das Gerät, dass

Sie das Gehäuse zu kalibrieren. Während der Kalibrierung der Onboard-Prozessor

ermittelt intelligent die maximale sichere Leistung der Feldmitte, und sorgt dafür, dass

das Gehäuse nicht überschreitet diese Grenze. Sobald die Kalibrierung abgeschlossen

ist die geforderten Werte im permanenten Speicher abgelegt werden, ohne zusätzliche

Kalibrierung erforderlich.

• Para maximizar a potência para a opção câmera e aquecedor, a unidade exige que você

calibrar o gabinete. Durante a calibragem, o processador de bordo inteligentemente

determina a potência de saída máxima de segurança do midspan, e assegura que o

invólucro não exceder o limite. Uma vez que a calibração é completar os valores

necessários são armazenados na memória permanente, sem calibração adicional

necessário.

• Per massimizzare la potenza per l'opzione della fotocamera e il riscaldatore, l'unità

richiede la calibrazione del contenitore. Durante la calibrazione, il processore a bordo

determina in modo intelligente la potenza massima sicurezza del midspan, e assicura

che la custodia non superi tale limite. Una volta calibrazione è completa dei necessari

valori memorizzati nella memoria permanente, senza calibrazione aggiuntiva richiesta.

SECTION D: PoE 30W Input for 30W Camera

WARNING!

• The heater and blower will not start for 60 seconds

after power is applied to the product.

• Wait for the camera to completely boot up before

pressing the calibration button. This will allow for the

most accurate calibration.

• The heater and blower will not start for 60 seconds after power is applied to the product.

• Wait for the camera to completely boot up before pressing the calibration button. This

will allow for the most accurate calibration.

• Le chauffage et de ventilation ne démarre pas pendant 60 secondes après mise sous

tension est appliquée au produit.

• Attendez que l'appareil photo à démarrer complètement avant appuyant sur le bouton

d'étalonnage. Cela permettra pour le calibrage le plus précis.

• Die Heizung und das Gebläse wird nicht für 60 Sekunden nach dem Einschalten starten,

um das Produkt angewendet wird.

• Warten Sie, bis sich die Kamera komplett hochfahren, bevor Sie die Kalibrierung Taste.

Dies wird für die genaue Kalibrierung ermöglichen.

• Aquecedor e soprador A não será iniciado durante 60 segundos após a energia é aplicada

ao produto.

• Aguarde até que a câmera completamente arrancar antes de premir o botão de

calibração. Isto irá permitir a calibração mais precisas.

• Il riscaldamento e sofante non inizierà per 60 secondi dopo l'alimentazione è applicata

al prodotto.

• Attendere che la macchina fotograca per avviare completamente a prima di premere il

pulsante di calibrazione. Questo permetterà la taratura più accurata.

Black (-)

Red (+)

Power to Camera (12Vdc)

{

24Vac

(

)

(

)

- Terminate incoming 24Vac on board.

- Shunts should be installed on 24Vac

jumpers.

- Terminate the 12Vdc leads (coming

from power supply mounted on

husing lid) into corresponding

terminals on camera.

• Terminar 24Vac entrantes a bordo.

- Las derivaciones se deben instalar en los puentes

de 24 VAC.

- Terminar los conductores de 12 VCC (procedente

de la fuente de alimentación montada en la tapa

Husing) en los terminales correspondientes de la

cámara.

• Mettre n à 24Vac entrants à bord.

- Shunts doivent être installés sur les cavaliers 24Vac.

- Terminer les ls 12Vdc (en provenance de

l'alimentation monté sur Hüsing couvercle) dans les

terminaux correspondants sur l'appareil photo.

• Beenden Sie eingehende 24Vac an Bord.

- Shunts sollte auf 24Vac Jumper installiert werden.

- Beenden Sie die Leads 12Vdc (kommend von der

Stromversorgung auf Hüsing Deckel montiert) in

entsprechende Endgeräte vor der Kamera.

• Encerra 24Vac entrada a bordo.

- Shunts deve ser instalado em jumpers 24VAC.

- Terminar as ligações 12VDC (proveniente de fonte

de alimentação montada no Hüsing tampa) em

terminais correspondentes na câmera.

• Termina 24Vac in arrivo a bordo.

- Shunt deve essere installato su ponticelli 24Vac.

- Terminare i cavi 12Vdc (provenienti dalla rete di

alimentazione montato su husing coperchio) nei

terminali corrispondenti sulla macchina fotograca.

SECTION C: 12Vac Input for 12Vdc Camera

Connect the network cable from the

midspan to the connector that is labeled

“To Network” connect the camera to the

connector labeled “To Camera”. When

power is applied the “Heat” LED will turn

ON for 5 seconds. 60 seconds the blower

will start.

• Conecte el cable de red del centro de la luz en el conector

que tiene la etiqueta "Para Red", conecte la cámara al

conector con la etiqueta "Para la cámara". Cuando la

energía se aplica el "calor" LED se encenderá durante 5

segundos. 60 segundos, el ventilador se enciende.

• Branchez le câble réseau de la mi-portée sur le connecteur

qui est étiqueté «Pour Réseau" connecter l'appareil photo

au connecteur marqué "à la caméra". Lorsqu'une tension

est appliquée la "chaleur" LED s'allume pendant 5

secondes. 60 secondes le ventilateur démarre.

• Schließen Sie das Netzwerkkabel aus dem Midspan an

den Anschluss, die den Namen "Zum Network" schließen

Sie die Kamera an den Anschluss mit der Aufschrift "Zur

Kamera". Wenn die Macht der "Heat" wird angewendet

LED für 5 Sekunden einzuschalten. 60 Sekunden das

Gebläse startet.

• Conecte o cabo de rede do midspan ao conector que

é rotulado de "rede" conectar a câmera ao conector

identicado como "Para Camera". Quando a energia

é aplicada a "Heat" LED irá acender por 5 segundos.

60 segundos, o ventilador começará.

• Collegare il cavo di rete dal midspan al connettore che

viene etichettato come "alla rete" collegare la fotocamera

al connettore etichettato "Per Camera". Quando il potere

è applicato il "Heat" LED si accende per 5 secondi. 60

secondi il ventilatore si avvia.

To Network To Camera

Press the Calibration button for one second.

Both the Test and Heat LED will turn ON.

Once the unit has been successfully

calibrated, the Test and Heat LED will turn

OFF. Once this is complete the Heat LED

will turn ON only if the heater is ON.

• Pulse el botón de calibración durante un segundo. Tanto la

prueba y el calor se encenderá. Una vez que la unidad ha

sido calibrado correctamente, la prueba y el calor del LED

se apagará. Una vez que se trata de completar el calor se

encenderá sólo si el calentador está encendido.

• Appuyez sur le bouton d'étalonnage pour une seconde.

Tant le test et la chaleur LED s'allume. Une fois l'appareil

a été étalonné avec succès, le test et la chaleur LED

s'éteindra. Une fois cette opération terminée, la chaleur

LED s'allume que si le chauffage est allumé.

• Drücken Sie die Taste Kalibrierung für eine Sekunde.

Sowohl der Test-und Wärme-LED leuchtet auf. Sobald

das Gerät erfolgreich kalibriert wurde, wird die Test-und

Wärme-LED auszuschalten. Sobald dies abgeschlossen

ist die Wärme-LED leuchtet auf, wenn die Heizung an ist.

• Pressione o botão de calibração para um segundo.

Tanto o teste como calor LED acenderá. Uma vez que

o aparelho foi calibrado com sucesso, o teste e calor

LED apaga-se. Uma vez que este é completar o calor

LED acenderá se o aquecedor está ligado.

• Premere il pulsante di calibrazione per un secondo. Sia

il test e di calore LED si accende. Una volta che l'unità è

stata correttamente calibrata, il collaudo e calore LED si

spegne. Una volta che questo è completare il calore LED

si accende solo se il riscaldatore è ON.

Test LED

Heat LED

Calibration

Button

The camera tray can be securely locked into place with

the provided 3.5 x 7mm screw. Tighten it through the

rear tray tab.

• La bandeja de la cámara se puede trabar con seguridad en lugar con el

tornillo proporcionado de 3.5 x de 7m m. Apriétela a través de la

lengüeta posterior de la bandeja.

• Le plateau d'appareil-photo peut être solidement fermé à clef sur

l'endroit avec la vis fournie de 3.5 x de 7mm. Serrez-le par l'étiquette

arrière de plateau.

• Der Kamerabehälter kann in Platz mit der zur Verfügung gestellten 3.5 x

7mm Schraube sicher verriegelt werden. Ziehen Sie ihn durch den

hinteren Behältervorsprung fest.

• A bandeja da câmera pode ser rmemente fechado no lugar com o

parafuso fornecido de 3.5 x de 7mm. Aperte-a através da aba traseira da

bandeja.

• Il vassoio della macchina fotograca può essere saldamente bloccato nel

posto con la vite fornita di 7mm x di 3.5. Stringalo attraverso la linguetta

posteriore del vassoio.

Close the housing lid and securely tighten the

(2) lid screws.

• Cierre la tapa de la cubierta y apriete con seguridad (2) los tornillos

de la tapa.

• Fermez le couvercle de logement et serrez solidement (2) les vis

de couvercle.

• Schließen Sie die Gehäusekappe und ziehen Sie sicher die (2)

Kappenschrauben fest.

• Feche a tampa da carcaça e aperte rmemente (2) os parafusos

da tampa.

• Chiuda il coperchio dell'alloggiamento e saldamente stringa (2) il

coperchio avvita.

Adjust the aim of the housing by loosening the

screw on the mount arm.

• Ajuste la puntería de la cubierta aojando el tornillo en el brazo

del montaje.

• Ajustez le but du logement en desserrant la vis sur le bras de bâti.

• Justieren Sie das Ziel des Gehäuses, indem Sie die Schraube am

Einfassungsarm lösen.

• Ajuste o alvo da carcaça afrouxando o parafuso no braço da montagem.

• Registri lo scopo dell'alloggiamento allentando la vite sul braccio del

supporto.

Hex tool

After powering your system up, make necessary

focus and camera adjustments.

• Después de accionar su sistema para arriba, haga los ajustes

necesarios del foco y de la cámara.

• Après avoir mis votre système, faites les ajustements nécessaires

de foyer et d'appareil-photo.

• Nachdem Sie oben Ihr System angetrieben haben, nehmen Sie

notwendige Fokus- und Kamerajustagen vor.

• Após ter psto seu sistema acima, faça ajustes necessários do foco

e da câmera.

• Dopo la potenza del vostro sistema in su, procedi alle registrazioni

necessarie della macchina fotograca e del fuoco.

If your housing has a sunshield, adjust it for your

particular lighting conditions by loosening (2) screws.

• Si su cubierta tiene un sunshield, ajústelo para que haya sus condiciones

de iluminación particulares aojando (2) los tornillos.

• Si votre logement a un sunshield, ajustez-le à vos états d'éclairage

particuliers en desserrant (2) des vis.

• Wenn Ihr Gehäuse ein sunshield hat, stellen Sie es auf Ihre bestimmten

Beleuchtungzustände ein, indem Sie (2) Schrauben lösen.

• Se sua carcaça tem um sunshield, ajuste-o para suas condições de

iluminação particulares afrouxando (2) os parafusos.

• Se il vostro alloggiamento ha un sunshield, registrilo per ottenere le

vostre condizioni di luce particolari allentando (2) avvita.

Wire Gauge

Total vA

consumed

,75

1,0

1,5

2,5

AWG

5.5

400

121

600

182

960

292

- - -

120

36.5

180

54.9

300

91.4

480

146

800

243

1300

396

27.1

141

43.0

225

68.6

358

109

571

174

905

275

1440

438

19.8

27.4

130

39.6

225

68.6

350

106

525

160

830

252

13.4

21.3

112

34.1

179

54.6

285

86.9

452

138

720

219

10.6

17.1

27.4

143

43.6

228

69.5

362

110

576

175

9.4

14.3

22.9

119

36.2

190

57.9

301

91.7

480

146

8.8

12.2

19.5

102

31.1

163

49.7

258

78.6

411

125

7.6

10.3

16.8

25.9

140

42.7

215

65.5

340

103

These are recommended maximum distances

for 24VAC with a 10% voltage drop.

• Éstos se recomiendan las distancias máximas para

24VAC con una caída de voltaje del 10%.

• Ceux-ci sont recommandés des distances maximum

pour 24VAC avec une chute de tension de 10%.

• Diese werden maximale Abstände für 24VAC mit

einem 10% Spannungsabfall empfohlen.

• Estes são recomendados distâncias máximas para

24VAC com uma queda de tensão de 10%.

• Questi sono suggeriti distanze massime per 24VAC con

una differenza de potenziale di 10%.

SPECIAL NOTE FOR 360 VIEWING APPLICATIONS

A. Horizontal mast mount 360 viewing B. Wall mount 360 viewing

# Part Number Description

1 RPVL3948 FCH Camera Tray

2 RPVL3950 FCH Heater + Bracket

3 RP76VL2016 FCH 12VDC/24VAC PCB

4 RPFD080 12VDC 40mm Fan

5 RPVL3953 Cable Membrane (0.60" hole)

6 RPFTM2425G FCH Wall Mount Assembly

7 RPFCH11HP FCH Hardware Packet

8 RP71VLBL09 Outdoor Rated Fan (Thermiq only)

N/S RP76VL2018 FCHQ 12VDC/24VAC PCB

N/S RP76VL2023 FCHQ PoE PCB

Replacement Parts

FCH11

Product Registration/Warranty

Thank you for choosing Moog Videolarm. We value your patronage and are solely committed to providing you with the highest

quality products available and superior customer service.

Should a problem arise, rest assured that Moog Videolarm stands behind its products by offering impressive 3 Year and 5 Year warranties, depending on the product

purchased. See full warranty details at www.moogvideolarm.com/technical-support/warranty-plan/

Please take a few moments to register your purchase via the Online Product Registration Form at:

www.moogvideolarm.com/technical-support/product-registration

• Simple and Trouble-Free RMA process

• Receive product updates, and special promotion

• Eliminate the need to archive original purchase documents:

Receipts, Purchase Orders, etc…