ADEMCO Ademco 5802WXT Guide d'installation

Catégorie
Systèmes de contrôle d'accès de sécurité
Taper
Guide d'installation
ADEMCO 5802WXT Supervised Miniature
Transmitter – Installation Instructions
General Information
The ADEMCO 5802WXT is a wireless transmitter that may be worn around
the neck, on a wrist band or as an apparel clip that may also may be mounted
to a desk, dresser, etc. (necklace, band, and clip supplied). Pressing and
holding the transmitter button for two seconds sends a signal to the control
receiver. The 5802WXT is intended for use only with wireless alarm systems
that support 5800 Series devices.
The transmitter is supervised, i.e., it automatically sends a message to the
control receiver that includes battery status information every 70-90 minutes.
This transmitter can be programmed as any zone type response (e.g.,
Emergency Panics, Relay Action, etc.).
Programming the Serial Number
The 5802WXT has a unique identification code (serial number) permanently
assigned during manufacture.
You must “enroll” the transmitter’s serial number and loop number during
system programming. The 5802WXT may be defined as Input Type “RF”
(supervised RF, for an hourly check-in; do not take out of range) or “UR
(Unsupervised RF). Its loop number is “1.” See the control unit’s Installation
Instructions for further details regarding programming. When installation is
complete, verify operation from desired location(s).
Battery Replacement
The 5802WXT is powered by a long-life Lithium battery that may be replaced
when a low battery is eventually indicated by the control unit.
NOTE: When replacing the battery, wait a minimum of 30 seconds prior to installing the
new battery.
NOTE: Although water-resistant, please do not immerse in water at a depth below
10cm for more than 1 hour.
1. Remove 4 screws and lift off
cover.
2. Using a small flat-blade
screwdriver remove old battery.
3. Insert new battery by placing
new battery under the gold tab
and then pressing down.
Ensure the POS + side of
battery is face up after
installation.
4. Align cover and attach with 4
screws.
5802WXT-001-V0
BATTERY
SCREWS (4) TYP.
5802WXT-002-V0
INSERT BATTERY
UNDER GOLD TAB
AND PRESS DOWN
Specifications
Unit Dimensions:
1.5” (3.9mm) Diameter
LED:
Lights when unit transmits.
Battery:
3-Volt 2032 Lithium
In ETL installations: 3V Panasonic or SENER
CR2032 only
REFER TO THE INSTALLATION INSTRUCTIONS FOR THE RECEIVER/CONTROL
WITH WHICH THIS DEVICE IS USED FOR WARRANTY INFORMATION AND FOR
DETAILS REGARDING THE LIMITATIONS OF THE ENTIRE ALARM SYSTEM.
ETL US Listings: HOUSEHOLD BURGLARY WARNING SYSTEM CONTROL UNIT ACCESSORY ETL Canadian
Listings: HOUSEHOLD BURGLARY WARNING SYSTEM CONTROL UNIT ACCESSORY ALSO LISTED FOR USE AS
A SIGNAL APPLIANCE, MISCELLANEOUS CERTIFIED FOR CANADA.
FEDERAL COMMUNICATIONS COMMISSION STATEMENTS
The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions
or User's Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment.
FCC/IC STATEMENT
This device complies with Part 15 of the FCC Rules, and RSS 210 of IC. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received,
including interference that may cause undesired operation.
Cet appareil est conforme à la partie 15 des règles de la FCC & de RSS 210 des Industries Canada. Son fonctionnement
est soumis aux conditions suivantes: (1) Cet appareil ne doit pas causer d' interferences nuisibles. (2) Cet appareil doit
accepter toute interference reçue y compris les interferences causant une reception indésirable.
IC MODEL: 5802WXT
2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747
Copyright 2011 Honeywell International Inc.
www.honeywell.com/security
Ê800-090083Š
800-09008 5/11 Rev. C
  • Page 1 1
  • Page 2 2

ADEMCO Ademco 5802WXT Guide d'installation

Catégorie
Systèmes de contrôle d'accès de sécurité
Taper
Guide d'installation

dans d''autres langues