Vulcan VCRG36-T Le manuel du propriétaire

©ITW Food Equipment Group, LLC

3600 North Point Blvd.

Baltimore, MD 21222

RETAIN THIS MANUAL FOR FUTURE USE

FORM F-38305 (rev. 9-15)

INSTALLATION & OPERATION MANUAL

MEDIUM DUTY GAS GRIDDLES

VCRG48-T

MODELS

VCRG24-T

VCRG36-T

VCRG48-T

WCRG24-T

WCRG36-T

WCRG48-T

For additional information on Vulcan or to locate an authorized parts and

service provider in your area, visit our website at www.vulcanequipment.com

- 2 -

IMPORTANT FOR YOUR SAFETY

THIS MANUAL HAS BEEN PREPARED FOR PERSONNEL QUALIFIED TO

INSTALL GAS EQUIPMENT, WHO SHOULD PERFORM THE INITIAL FIELD

START-UP AND ADJUSTMENTS OF THE EQUIPMENT COVERED BY THIS

MANUAL.

POST IN A PROMINENT LOCATION THE INSTRUCTIONS TO BE FOLLOWED IN

THE EVENT THE SMELL OF GAS IS DETECTED. THIS INFORMATION CAN BE

OBTAINED FROM THE LOCAL GAS SUPPLIER.

IMPORTANT

IN THE EVENT A GAS ODOR IS DETECTED, SHUT

DOWN UNITS AT MAIN SHUTOFF VALVE AND

CONTACT THE LOCAL GAS COMPANY OR GAS

SUPPLIER FOR SERVICE.

FOR YOUR SAFETY

DO NOT STORE OR USE GASOLINE OR OTHER

FLAMMABLE VAPORS OR LIQUIDS IN THE VICINITY OF

THIS OR ANY OTHER APPLIANCE.

IN THE EVENT OF A POWER FAILURE, DO NOT

ATTEMPT TO OPERATE THIS DEVICE.

Improper installation,

adjustment, alteration, service or maintenance

can cause property damage, injury, or death.

Read the installation, operating and maintenance

instructions thoroughly before installing or

servicing this equipment.

- 3 -

INSTALLATION, OPERATION AND CARE OF

MEDIUM DUTY GAS GRIDDLES

GENERAL

Medium Duty Gas Griddles are produced with quality workmanship and materials. Proper

installation, usage and maintenance of your griddle will result in many years of

satisfactory performance.

Thoroughly read this entire manual and carefully follow all of the instructions provided.

Model

Number Of Burners

BTU/hr Input Rating

VCRG24-T / WCRG24-T

2

50,000

VCRG36-T / WCRG36-T

3

75,000

VCRG48-T / WCRG48-T

4

100,000

INSTALLATION

UNPACKING

This griddle was inspected before leaving the factory. The carrier assumes full responsibility for the

safe delivery upon acceptance of the shipment. Check for possible shipping damage immediately after

receipt.

If the griddle is found to be damaged, complete the following steps:

1. Carrier must be notified within 5 business days of receipt.

2. Carrier’s local terminal must be notified immediately upon discovery (note time, date, and

who was spoken to), and follow up and confirm with written or electronic communication.

3. All original packing materials must be kept for inspection purposes.

4. The griddle cannot have been moved, installed, or modified.

5. Notify Vulcan Customer Service immediately at 800-814-2028.

Carefully unpack your griddle and make sure that no parts are discarded with packaging

material. A pressure regulator designed to operate with the griddle has been supplied and

must be installed before the griddle is placed into service (Refer to GAS PRESSURE

REGULATOR INSTALLATION in this manual).

LOCATION

The installation location must be kept free and clear of combustibles. When installing,

never enclose the bottom of the griddle with a raised curb or other constructions that

would obstruct flow of air into or out of the griddle. Adequate clearance for air openings

into the combustion chamber must be provided. Make sure there is an adequate supply of

air in the room to replace air taken out by the ventilation system.

Do not permit air to blow directly at the griddle. Avoid open windows next to the griddle

wherever possible. Avoid wall-type fans which create air cross-currents within the room.

- 4 -

This griddle is Design Certified for installation on a non-combustible counter with 4” legs,

or combustible floor with 24” high stand.

INSTALLATION CLEARANCES

COMBUSTIBLE CONSTRUCTION

NON-COMBUSTIBLE CONSTRUCTION

Back:

6”

0”

Sides:

Side:

6”

0”

INSTALLATION CODES AND STANDARDS

The griddle must be installed in accordance with:

In the United States of America:

1. State and local codes.

2. National Fuel Gas Code, ANSI-Z223.1/NFPA #54 (latest edition). This shall include but

not be limited to: NFPA #54 Section 10.3.5.2 for Venting. Copies may be obtained

from The American Gas Association Accredited Standards Committee Z223, @ 400

N. Capital St. NW, Washington, DC 20001 or the Secretary Standards Council, NFPA,

1 Batterymarch Park Quincy, MA 02169-7471

NOTE: In the Commonwealth of Massachusetts

All gas appliances vented through a ventilation hood or exhaust system equipped with

a damper or with a power means of exhaust shall comply with 248 CMR.

3. NFPA Standard # 96 Vapor Removal from Cooking Equipment, latest edition, available

from the National Fire Protection Association, Batterymarch Park, Quincy, MA 02269.

In Canada:

1. Local codes.

2. CAN/CSA-B149.1 Natural Gas Installation (latest edition)

3. CAN/CSA-B149.2 Propane Installation Code (latest edition), available from the

Canadian Gas Association, 178 Rexdale Blvd., Etobicoke, Ontario, Canada M9W 1R3

GRIDDLES MOUNTED ON STANDS WITH CASTERS

Griddles mounted on stands with casters must use a

flexible connector (not supplied) that complies with the

Standard for Connectors for Movable Gas Appliances

ANSI Z21.69•CSA6.16, and a quick-disconnect device

that complies with Gas Fuel, ANSI Z21.3•CSA6.9. In

addition, adequate means must be provided to limit

movement of the appliance without depending on the

connector and the quick-disconnect device (or its

associated piping) to limit appliance movement. Attach

the restraining device at the rear of the griddle as

shown in Fig. 1.

Fig. 1

If disconnection of the restraint is necessary, turn off the gas supply before

disconnecting. Reconnect the restraint prior to turning the gas supply on and returning

the griddle to its installation position.

Casters are only supplied on a griddle stand. If the griddle is moved for any reason the

griddle should be re-leveled (see LEVELING in this manual).

- 5 -

FLUE CONNECTIONS

Do not obstruct the flow of flue gases from the flue, located at the rear of the griddle. It is

recommended that flue gases be ventilated to the outside of the building through a

ventilation system installed by qualified personnel.

From the termination of the flue to the filters of the hood venting system, a minimum

clearance of 18” must be maintained.

Information on the construction and installation of ventilating hoods may be obtained from

the standard for “Vapor Removal from Cooking Equipment”, NFPA No. 96 (latest edition),

available from the National Fire Protection Association, Batterymarch Park, Quincy, MA

02269.

GAS CONNECTIONS

Gas supply connections and any pipe joint compound must be resistant to the

action of propane gases.

Use a ¾” NPT gas supply line for the griddle inlet, located at the rear of the griddle. All of

flexible and semi-rigid gas supply lines must comply with the applicable ANSI standard.

To ensure maximum operating efficiency, this appliance must be connected with a gas

supply line of solid pipe or a commercial type Flexible Connector with the net inside

diameter (I.D.) as large as or larger than the gas pipe inlet on this appliance. Codes

require that a gas shutoff valve must be installed in the gas line upstream of the griddle.

Prior to lighting, check all joints in the gas supply line for leaks.

Use soap and water solution. Do not use an open flame.

After checking for leaks all lines receiving gas should be fully purged to remove air.

TESTING THE GAS SUPPLY SYSTEM

When the gas supply pressure exceeds ½ psig (3.45 kPa), the griddle and its individual

shutoff valve must be disconnected from the gas supply piping system.

When the gas supply pressure is ½ psig (3.45 kPa) or less, the griddle should be isolated

from the gas supply system by closing its individual manual shutoff valve.

GAS PRESSURE REGULATOR INSTALLATION

This griddle is supplied with a convertible gas pressure regulator preset at 4” Water

Column (W.C.) for natural gas. No further adjustment should be required. Install the

regulator as close to the griddle on the gas supply line as possible. Make sure that the

arrow on the underside of the regulator is oriented in the direction of gas flow to the

griddle (Fig. 2 on next page) and the regulator is positioned with the vent plug and

conversion plug cover upright (Fig. 3 on next page).

- 6 -

Fig. 2

Fig. 3

The supply pressure (upstream of the regulator) should be 7-9” W.C. for natural gas and

11-12” W .C. for propane gas. At no time should the griddle be connected to supply

pressure greater than ½ psig (3.45 kPa) or 14” W.C.

PROPANE GAS CONVERSION

This griddle is shipped from the factory equipped with fixed burner and pilot orifices for

natural gas operation. The burner and pilot orifices required to convert the griddle to

propane gas are shipped with the griddle in the shipping packaging. It is recommended

that a trained gas service technician with the necessary tools, instruments and skills

perform the conversion.

Prior to lighting, check all joints in the gas supply line for leaks.

Use soap and water solution. Do not use an open flame.

To convert to propane, following steps

must be completed:

1. Remove all natural gas burner

orifices and install the provided

propane burner orifices. See Fig. 4

2. Remove all pilot orifices and install

the provided propane pilot orifices.

See Fig 4.

3. Set the regulator to 10” W.C. by

inverting the regulator spring plug.

See Fig 5.

Fig. 5

Fig. 4

PILOT

ORIFICE

BURNER

ORIFICE

- 7 -

OPERATION

The griddle and its parts are hot. Use care when operating, cleaning

or servicing the griddle.

BEFORE FIRST USE

Remove all packing material and protective plastic from surfaces of the unit. Before

leaving the factory, the griddle plate is coated with protective coating as a rust inhibitor.

Remove this film when the griddle plate is being cleaned prior to its first cooking use.

Heat the griddle to 200-300°F to loosen and melt the coating, then clean the surface with

a non-corrosive, grease dissolving commercial cleaner, following the manufacturer’s

directions. Rinse thoroughly and wipe dry with a soft clean cloth. Clean all accessories.

SEASONING THE GRIDDLE

Season the griddle to avoid possible surface corrosion before first use, and after every

cleaning. Heat griddle to a low temperature (300-350°F) and apply a small amount of

cooking oil – about one ounce per square foot of surface. Use a soft lint-free cloth to

spread the oil over the entire griddle surface to create a thin film. Wipe off any excess oil

with a cloth. Repeat the procedure until the griddle has a slick, mirror-like finish. This will

also help reduce the sticking of cooked food product.

CONTROLS

This model features a standing pilot that must be manually lit. The pilot is monitored by a

thermocouple and pilot safety valve. If the pilot goes out, the safety valve will shut-off

the gas supply to the pilot and main burners. There is one pilot and one safety valve for

every two burners except on the 36” model. The 36” model has an odd number of main

burners, therefore one of the sets of pilots and safety valves in these models will control

only one main burner. The safety valve push buttons are aligned with pilot burners and

the pilot sight holes are off centered ¾” to the right. The pilot burners are inset

approximately 7” from the front panel. See cutaway view on page 8.

Each 12” section of the griddle is independently controlled by a mechanical snap -action

thermostatic valve. The thermostats have an operating range of 200 to 450 degrees.

Once pilots are lit, turning the thermostats to the desired setting is all that is required to

put the unit into service.

- 8 -

VCRG-T / WCRG-T PILOT LIGHTING PROCEDURE

1. Turn the main gas shut-off valve and all thermostats to the OFF position. Wait 5 minutes to allow

any gas that may have accumulated in the burner compartment to escape.

2. Turn the main gas shut-off valve ON.

3. Depress and hold the safety valve button while lighting the corresponding pilot. You will have to

reach under the front of the unit to light with an outside ignition source(such as a lit taper, etc.) while

viewing thru the pilot sight hole.

4. When the gas at the pilot has been burning for about 45 seconds, release the safety valve button.

If the pilot does not remain lit, repeat the operation allowing more time before releasing the button.

The amount of time necessary to hold the safety valve button will increase at the initial installation of

the unit and if the main gas supply has been turned off for a long period of time. It may be

necessary to adjust the pilot valve to increase gas to the pilot. See Fig. 6 on page 12.

5. Repeat steps until all pilots are lit.

6. If after completing steps 1-5 pilot does not light, turn off the main gas shut-off valve and contact an

authorized service contractor.

CUTAWAY VIEW

PILOT BURNER

PILOT SIGHT HOLE

THERMOSTAT KNOB

SAFETY VALVE BUTTON

7”

- 9 -

USING THE GRIDDLE

To preheat, turn the burners on about 20-25 minutes before cooking.

A uniform and systematic approach to loading the griddle will produce the most consistent

product results.

The griddle plate is steel, but the surface can be scored or dented by careless use of a

spatula or scraper. Be careful not to dent, scratch, or gouge the plate surface. Do not try

to knock off loose food that may be on the spatula by tapping the corner or the edge of

the spatula on the griddle surface.

ZONE COOKING

This griddle features a tubular U-shaped burner in each 12” section, each controlled by

independent thermostats. Each 12” section is a separate cooking zone, and allows

cooking a wide variety of products over a single griddle plate. The chart below is a

suggested usage of zone cooking.

When zone cooking, it is suggested that you start with your lowest temperature setting at

either side of the griddle, increasing the zone temperature as you move up the zone line.

These zone cooking guidelines will vary depending on product temperatures, size and

shape. This guide should be adjusted to suit your product and operational cooking

preference.

ZONE 1

(300°F)

ZONE 2

(350°F)

ZONE 3

(350°F)

ZONE 4

(400°F)

PRODUCT

Sausage

Eggs (Hard Fried)

Eggs (Scrambled)

Burger (Well Done)

Steak (Well Done)

Chicken Breast

Frozen Foods

Pork Chops

PRODUCT

Steak (Rare)

Stir Fry Vegetables

Salmon

Fish Cakes

Lobster

Scampi

Pancakes

French Toast

Bacon

Omelet

Hash Browns

Canadian Bacon

Eggs (Sunny Side Up)

Boiled Ham

Steak (Medium Well)

Fresh Burger (Medium Well)

Small Frozen Burger (Medium Well)

- 10 -

CLEANING THE GRIDDLE

Empty the grease drawer as needed throughout the day and regularly clean at least once

daily.

Clean the griddle regularly. A clean griddle always looks better, lasts longer and performs

better. To produce evenly cooked, perfectly browned griddle products keep the griddle

plate clean and free of carbonized grease. Carbonized grease on the surface hinders the

transfer of heat from the griddle surface to the food, resulting in spotty browning and loss

of cooking efficiency. Carbonized grease tends to cling to griddle foods, giving them a

highly unsatisfactory and unappetizing appearance.

To keep the griddle clean and operating at peak efficiency, follow these procedures:

AFTER EACH USE

Clean the griddle with a wire brush or flexible spatula.

ONCE PER DAY

Thoroughly clean the griddle back splash, sides and front. Remove, empty and wash the

grease drawer in the same manner as an ordinary cooking utensil.

ONCE PER WEEK

Clean the griddle surface thoroughly. Use a griddle stone, screen, or Scotch Bright™ pad

on the surface as necessary. Rub with the grain of the metal while the griddle is still

warm (not hot). A detergent may be used on the plate surface to help clean it, but be sure

the detergent is thoroughly removed by flushing with clear water.

After removal of detergent the surface of the plate the griddle should be seasoned

according to the instructions in this manual.

Clean stainless steel surfaces with a damp cloth and polish with a soft dry cloth. To

remove discoloration, use a griddle cleaner.

If the griddle usage is very high, consider conducting this weekly cleaning procedure

more than once per week.

- 11 -

ADJUSTMENTS

CALIBRATION

1. Each thermostat controls a 12” zone of the

griddle. Using a Surface Probe temperature

measurement device, observe the temperatures

at the center points of the cooking zones.

These points are located by starting 6” from the

side splash (left or right) and every 12” across

the width of the griddle, with all points located

12” back from the front edge of the griddle

plate.

NOTE: Use of infrared thermometers is not

recommended. These devices are highly

sensitive to surface color (clean or dirty), angle

of reading and distance from the unit.

2. Set thermostats to 350°F and allow to stabilize,

allowing the burner to cycle ON and OFF at

least two times.

3. Watch for burner to cycle OFF, then measure

the temperature for that zone. The temperature

should be 350°F ±15°F. If not, continue to Step

4.

4. a. Carefully loosen the knob set

screw. DO NOT allow the knob to

turn. Carefully remove the knob

from the thermostat shaft,

exposing the temperature dial.

b. Loosen screws on the temperature

dial and adjust to that the

temperature indicated by the knob

arrow matches the griddle plate

temperature reading. Knob will

have to be placed back on the

shaft to verify adjustment.

IMPORTANT: NEVER ADJUST THE

SCREW IN THE CENTER OF THE

THERMOSTAT SHAFT. This will ruin the

factory calibration; the thermostat will no

longer operate properly and may need to

be replaced.

5. Once calibration is achieved, tighten the

temperature dial screws and knob set

screws.

Step 4a. Set knob &

check Temperature.

Remove knob

Step 4b. – Adjust

temperature dial &

verify temperature

setting

Step 5 –Replace

knob & tighten

screws

- 12 -

LEVELING

The griddle must be level (side-to-side and front-to-back) during operation to ensure

proper performance. Improper leveling can result in uneven temperature distribution, cold

spots, and possibly damaged components.

1. Place a level on the griddle.

2. Adjust legs by turning the bullet feet at the bottom of each leg. Using pliers or a

crescent wrench, turn the feet counter-clockwise to increase height, and clockwise to

decrease height until leveling is achieved. Do not extend the legs more than 1-¾”.

PILOT ADJUSTMENT

Using a flathead screwdriver, turn the slotted hex-head pilot adjustment screw clockwise

to decrease the flame, and counterclockwise to increase the flame. See Fig. 6.

Fig. 6

- 13 -

SHUTDOWN OF GRIDDLE

1. Turn thermostats to the OFF position to cut off burners.

2. The pilots will remain lit and monitored by the safety valve as long as the main gas

supply is on.

EXTENDED SHUTDOWN

1. Shut off the main gas supply valve.

2. Apply a heavy coat of vegetable oil over the griddle plate to inhibit rust.

MAINTENANCE

The griddle and its parts are hot. Use care when operating, cleaning

or servicing the griddle.

LUBRICATION

There are no parts on this griddle that require lubrication.

VENT

Daily, when the griddle is cool, check the flue and clear any obstructions.

SERVICE AND PARTS INFORMATION

Contact the Service Contractor in your area to obtain service and parts information. For a

complete listing of Service and Parts depots refer to or www.vulcanequipment.com.

When calling for service, the following information should be available from the appliance

identification plate: Model Number, Serial Number and Gas Type.

- 14 -

TROUBLESHOOTING

PROBLEM

POSSIBLE CAUSES

Burner does not come on

when the control knob is

turned on

1. Problem with gas valve. (Call for service)

2. Pilot burner not lit. (Call for service)

3. Low gas pressure. (Call for service)

Pilot burner will not light

1. Manual gas valve not turned on.

2. Obstructed pilot orifice. (Call for service)

3. Pilot gas turned off at pilot. Adjust pilot to allow gas flow.

4. Low gas pressure. (Call for service)

Pilot burner will not stay

lit

1. Obstructed or wrong size pilot orifice. (Call for service)

2. Gas supply not purged of air. Depress pilot safety button

until air is purged.

3. Air blowing pilot out. (Call for service)

4. Low gas pressure. (Call for service)

Fat appears to smoke

excessively

1. Temperature set too high.

2. Moisture in food may be turning into steam

Food sticks to griddle or

burned around edges or

contains dark specs

1. Temperature set too high.

2. Griddle surface requires cleaning and/or seasoning.

3. Surface under food not covered with enough cooking oil.

Food under-cooked inside

1. Temperature set too low.

2. Food not cooked for long enough time.

Food tastes greasy or has

objectionable off-flavor

1. Food itself may have off-flavor.

2. Food stored improperly before cooking.

3. Too much griddle fat used.

4. Temperature set too low.

Noticeable build-up of

gum on griddle

1. Temperature set too high.

2. Griddle surface needs cleaning and/or seasoning.

3. Too much griddle fat used.

- 14 -

DÉPANNAGE

PROBLÈME

CAUSES POSSIBLES

Le brûleur ne s’ouvre pas

lorsque le bouton de

commande est ouvert

1. C’est un problème avec la soupape à gaz (Contactez

le service à la clientèle).

2. La veilleuse du brûleur n’est pas allumée. (Contactez

le service à la clientèle).

3. La pression du gaz est basse. (Contactez le service à

la clientèle).

La veilleuse n’est pas

allumée

1. La soupage manuelle du gaz n’est pas ouverte.

2. L’orifice de la veilleuse d’allumage est obstrué.

(Contactez le service à la clientèle).

3. La veilleuse du gaz est fermée. Réglez la veilleuse

d’allumage pour permettre la circulation du gaz.

4. La pression du gaz est basse. (Contactez le service à la

clientèle).

La veilleuse d’allumage ne

reste pas allumée

1. L’orifice de la veilleuse d’allumage est obstrué ou n’a pas

la bonne dimension. (Contactez le service à la clientèle).

2. L’alimentation en gaz n’a pas été vidée de son air. Appuyez

sur le bouton de la soupape de sûreté jusqu’à ce que l’air

soit évacué.

3. Il y a de l’air qui sort de la veilleuse. (Contactez le service

à la clientèle).

4. La pression du gaz est basse. (Contactez le service à la

clientèle).

Le gras semble causer de la

fumée de façon excessive

1. La température est trop haute.

2. L’humidité dans la nourriture peut se transformer en vapeur

La nourriture colle sur la

plaque ou brûle sur les

bouts ou a des taches

foncées

1. La température est trop haute.

2. La surface de la plaque nécessite un nettoyage ou un rodage.

3. La surface sous la nourriture n'a pas été assez enduite d’huile

végétale.

La nourriture n’est pas

assez cuite à l’intérieur

1. La température est trop basse.

2. La nourriture n’a pas été cuite assez longtemps.

La nourriture goûte le gras

ou a un goût altéré

désagréable

1. La nourriture elle-même a un goût altéré.

2. La nourriture a été gardée dans de mauvaises conditions avant

la cuisson.

3. Il y a trop de gras utilisé sur la plaque

4. La température est trop basse.

Accumulation visible de

gomme sur la plaque

1. La température est trop haute.

2. La surface de la plaque a besoin d’un nettoyage ou d’un

rodage.

3. Il y a trop de gras utilisé sur la plaque

- 13 -

FERMERTURE LA PLAQUE CHAUFFANTE

1. Fermez les thermostats pour éteindre les brûleurs.

2 Les veilleuses resteront allumées et contrôlées par la soupape de sûreté aussi longtemps que

l’alimentation principale en gaz est ouverte

FERMETURE PROLONGÉE

1. Fermez le robinet principal d’alimentation en gaz.

2. Mettez une généreuse couche d’huile végétale sur la plaque pour empêcher la rouille.

ENTRETIEN

La plaque chauffante et ses pièces sont chaudes. Faites

attention lorsque vous employez, nettoyez ou entretenez la plaque chauffante.

LUBRIFICATION

Il n’y a aucune pièce sur cette plaque chauffante qui a besoin d’être lubrifiée.

VENTILATION

Quotidiennement, lorsque la plaque chauffante est refroidi, vérifiez le conduit et retirez

toute obstruction.

RENSEIGNEMENTS SUR L’ENTRETIEN ET LES PIÈCES

Contactez l’agence de service de votre région pour obtenir des renseignements sur

l’entretien et les pièces. Pour une liste des bureaux des services et des pièces,

consultez www.vulcanequipment.com.

Lorsque vous appelez pour du service, les renseignements suivants devraient être

disponibles sur la plaque d'identification de l'appareil : le numéro du modèle, le numéro

de série et le type de gaz.

- 12 -

MISE À NIVEAU

La plaque chauffante doit être mise à niveau (d’un côté à l’autre et du devant vers l’arrière)

quand vous l'utilisez pour assurer une performance adéquate. Une mise à niveau inadéquate

peut provoquer une répartition de la température inégale, des zones froides et possiblement des

composants endommagés.

1. Placez un niveau sur la plaque chauffante.

2. Réglez les pattes en tournant les pieds en bas de chaque patte. À l’aide d’une pince -étau ou

d’une clé à molette, tournez les pieds dans le sens contraire des aiguilles d'une montre pour

augmenter la hauteur et dans le sens des aiguilles d'une montre pour diminuer la hauteur

jusqu’à ce que la mise à niveau soit effectuée. Ne pas allonger les pattes plus de 4 cm.

RÉGLAGE DE LA VEILLEUSE D’ALLUMAGE

À l’aide d’un tournevis à tête plate, tournez la vis à tête hexagonale fendue de réglage de la

veilleuse d’allumage dans le sens des aiguilles d'une montre pour diminuer la flamme et dans le

sens contraire des aiguilles d'une montre pour augmenter la flamme. Voir Fig. 6.

Fig. 6

- 11 -

RÉGLAGES

CALIBRAGE

1. Chaque thermostat contrôle une zone de 30 cm

de la plaque chauffante. À l’aide d’une sonde de

surface permettant de mesurer la température,

observez les températures aux points centrés de

la zone de cuisson. Ces points sont situés en

commençant à 15 cm à partir du côté contre les

éclaboussures (gauche ou droit) et à chaque 30

cm de la largeur de la plaque, avec tous les

points situés à 30 cm à l’arrière de la partie

antérieure de la plaque.

REMARQUE : L’utilisation de thermomètres à

infrarouges n’est pas recommandée. Ces

dispositifs sont très sensibles pour la couleur de

la surface (propre ou sale), l’angle de lecture et

la distance avec l’appareil.

2. Réglez les thermostats à 350°F et laissez-les se

stabiliser afin d’aider le brûleur à se fermer et à

s’ouvrir au moins deux fois.

3. Assurez-vous que le brûleur se ferme, puis

mesure la température de cette zone. The

temperature devrait être de 350°F ±15°F. Si ce

n’est pas le cas, continuez à l’étape 4.

4. a. Dévissez soigneusement la vis de

réglage du bouton. NE PAS

permettre au bouton de tourner.

Retirez soigneusement le bouton

de l’arbre du thermostat, exposant

le cadran des températures.

b. Dévissez les vis du cadran des

températures et réglez pour que la

température indiquée par la flèche

du bouton corresponde à la

température de la plaque

chauffante. Le bouton devra être

replacé dans l’arbre pour vérifier

le réglage.

IMPORTANT NE JAMAIS AJUSTER LA

VIS AU CENTRE DE L’ARBRE DU

THERMOSTAT. Cela endommagera le

calibrage effectué en usine; le thermostat

ne fonctionnera plus adéquatement et

aura peut-être besoin d’être remplacé.

5. Une fois le calibrage terminé, resserrez

les vis du cadran des températures et du

réglage du bouton.

Étape 4a. Réglez le

bouton et vérifiez la

température. Retirez

le bouton

Étape 4b. – Réglez le

cadran des

températures et

vérifiez le réglage de

la température.

Étape 5 – Remettez le

bouton et resserrez

les vis.

- 10 -

NETTOYAGE LA PLAQUE CHAUFFANTE

Videz le tiroir à graisse au besoin tout au long de la journée et le nettoyez régulièrement au

moins une fois par jour.

Nettoyez régulièrement la plaque chauffante Une plaque chauffante propre a toujours un meilleur

aspect, dure plus longtemps et a une meilleure performance. Pour obtenir des aliments cuits de

façon uniforme et parfaitement grillés, garder la plaque propre et sans gras carbonisé. Le gras

carbonisé sur la surface empêche le transfert la chaleur de la surface de la plaque à la

nourriture, provoquant du brunissement par endroits et de la perte d’efficacité de cuisson. Le

gras carbonisé a tendance à adhérer aux aliments cuits sur plaque, leur donnant une apparence

très insatisfaisante et peu appétissante.

Pour garder la plaque chauffante propre et l’utiliser à un rendement optimum, suivez ces

procédures :

APRÈS CHAQUE UTILISATION

Nettoyez la plaque chauffante avec une brosse métallique ou une spatule flexible.

UNE FOIS PAR JOUR

Nettoyez à fond le dos antiéclaboussement, les côtés et le devant de la plaque chauffante.

Retirez, videz et lavez le tiroir à graisse de la même façon qu’un ustensile de cuisine ordinaire.

UNE FOIS PAR SEMAINE

Nettoyez à fond la surface de la plaque chauffante. Utilisez une pierre pour plaque chauffante,

une toile ou un tampon Scotch Bright sur la surface au besoin. Frottez avec le grain métallique

pendant la plaque est encore tiède (pas chaude). Vous pouvez utiliser un détersif sur la surface

de la plaque pour vous aider à nettoyer, mais assurez-vous qu’il n'en reste plus en rinçant avec

de l'eau claire.

Après avoir enlevé le détersif, la surface de la plaque devrait être rodée selon les instructions de

ce manuel.

Nettoyez la surface en acier inoxydable avec un linge humide et polissez avec un linge sec doux.

Pour enlever la décoloration, utilisez un nettoyant pour plaque chauffante.

Si vous utilisez très souvent la plaque chauffante, songez à effectuer cette procédure

hebdomadaire de nettoyage plus d’une fois par semaine.

- 9 -

UTILISATION LA PLAQUE CHAUFFANTE

Pour préchauffer, ouvrez les brûleurs environ 20 à 25 minutes avant la cuisson.

Un approche uniforme et méthodique pour remplir la plaque chauffante produira les résultats les

plus constants.

La plaque est en acier, mais la surface peut être rayée ou bosselée par un mauvais usage d'une

spatule ou d’un grattoir. Faites attention de ne pas bosseler, égratigner ou percer la surface de

la plaque. Ne pas essayer de retirer la nourriture qui se retrouve sur la spatule en tappant sur le

coin ou le bout de la spatule sur la surface de la plaque.

ZONES DE CUISSON

La plaque a un brûleur tubulaire en forme de U dans chaque section de 30 cm, chacun contrôlé

par des thermostats indépendants. Chaque section de 30 cm est une zone de cuisson séparée et

permet la cuisson d’un grand nombre de produits sur une seule plaque. Le graphique ci-dessous

démontre un usage suggéré des zones de cuisson.

Lorsque vous utilisez les zones de cuisson, nous vous suggérons de commencer par celle qui a

la plus basse température d'un côté ou l'autre de la plaque et d'augmenter la température des

zones au fur et à mesure que vous vous déplacez tout au long de celles-ci. Ces directives pour

les zones de cuisson varieront selon les températures, la taille et la forme du produit. Ce guide

devrait être réglé selon votre préférence de produits et de fonctionnement lors de la cuisson.

ZONE 1

(300°F)

ZONE 2

(350°F)

ZONE 3

(350°F)

ZONE 4

(400°F)

PRODUIT

Saucisse

Oeufs (poêlés)

Oeufs (brouillés)

Hamburger (bien

cuit)

Bifteck (bien cuit)

Poitrine de poulet

Aliments congelés

Côtelette de porc

PRODUIT

Bifteck

(saignant)

Légumes sautés

Saumon

Galettes de

poisson

Homard

Langoustine

Crêpes

Pain doré

Bacon

Omelette

Pommes de terre

rissolées

Bacon de dos

Oeufs (au miroir)

Jambon blanc

Bifteck (médium)

Hamburger (médium)

Petit hamburger congelé (médium)

La page charge ...

Vulcan VCRG36-T Le manuel du propriétaire

Vulcan VCRG36-T Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents