FCC/IC
Federal Communications Commission (FCC) Statement
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may caus harmful interference to radio communications.However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.Increase the separation between the equipment and
receiver.Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.Consult the dealer or an experienced radio/TV technician for help.This equipment
should be installed and operated with minimum distance 20cm between the radiator and your body.
IC Caution:
Door window sensor
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject
to the following two conditions: (1) this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause undesired
operation of the device.
ZW1103 Smoke Sensor
Smoke Sensor
DECLARATION DE CONFORMITE D'INDUSTRIE CANADA
Ce périphérique a été testé et reconnu conforme aux limites spéci
fiées dans RSS-210.
Son utilisation est soumise aux deux conditions suivantes :
(1) il ne doit pas provoquer d'interférences gênantes et
(2) il doit tolérer les interférences re.ues, notamment cellessusceptibles d'en perturber le fonctionnement.
EVALOGIK Products warrants this product to be free from manufacturing defects for
a period of two years from the original date of consumer purchase. This warranty is limited
to the repair or replacement of this product only and does not extend to consequential or
RISK OF FIRE
incidental damage to other products that may be used with this product.
RISK OF ELECTRICAL SHOCK
RISK OF BURNS
This warranty is in lieu of all other warranties, expressed or implied. Some states do not
CONTROLLING APPLIANCES:
allow limitations on how long an implied warranty lasts or permit the exclusion or limitation
EXERCISE EXTREME CAUTION WHEN USING Z-WAVE
of incidental or consequential damage, so the above limitations may not apply to you.
DEVICES TO CONTROL APPLIANCES. OPERATION
This warranty gives you speci
fic rights, and you may also have other rights which vary from
OF THE Z-WAVE DEVICE MAY BE IN A DIFFERENT
state to state. if the unit should prove defective within the warranty period.
ROOM THAN THE CONTROLLED APPLIANCE, ALSO AN
UNINTENTIONAL ACTIVATION MAY OCCUR IF THE WRONG
BUTTON ON THE REMOTE IS PRESSED. Z-WAVE DEVICES
MAY AUTOMATICALLY BE POWERED ON DUE TO TIMED
EVENT PROGRAMMING. DEPENDING UPON THE APPLI-
ANCE, THESE UNATTENDED OR UNINTENTIONAL OP-
Model:ZW1103
ERATIONS COULD POSSIBLY RESULT IN A HAZARDOUS
Power supply: CR123A, 3V.
CONDITION. FOR THESE REASONS, WE RECOMMEND
Signal (Frequency): 908.42 MHz.
DO NOT RETURN THIS PRODUCT TO THE STORE
Operating Range: Up to 50M outdoor,30M indoor
THE FOLLOWING:
Operating Temp.: 0°C~55°C
DO NOT USE Z-WAVE DEVICES TO CONTROL ELECTRIC
Operating Humidity: 0%~93%
HEATERS OR ANY OTHER APPLIANCES WHICH MAY PRESENT
Measured Temperature Range:-20°C~100°C
A HAZARDOUS CONDITION DUE TO UNATTENDED OR
Wireless Controller and the closest Z-Wave
UNINTENTIONAL OR AUTOMATIC POWER ON CONTROL.
receiver module.
Speci
fications subject to change without notice
due to continuing product improvement
Website www.nie-tech.com
Pre cautions:
1. Read this manual before attempting to install the device. Take special precautions during installation, use tools and
equipment in perfect working order. It’s recommended to observe ladders, lifts and other obstacles.
2. Depending on the Smoke Sensors internal conditions (e.g. battery discharge, device failure, etc.) and ambient conditions,
fire alarms, are not always effective in all situations. Smoke Sensors must be tested regularly according to this operating
WARRANTY
SPECIFICATIONS
WARNING
Important safeguards
regularly inspected as well.
1. It’s recommended to install the sensor on the ceiling or upper portion of wall at least 40cm (2 feet) from corners and other
objects. Particular attention should be paid to any adjacent objects or devices which can impede smoke’s access to the sensor.
It’s recommended to install Smoke Sensor in all rooms prone to
fire, and in between such rooms as well.
2. Add the device into the Z-Wave network. Note the adding process may be performed ONLY in direct range of the main controller.
3. Install the sensor’s cover in desired location.
4. Screw the Smoke Sensor into the cover.
5. If the sensor is already added into the Z-Wave network, wake it up by clicking the ADD Button. Otherwise, add the device as
described as below.
6. Test Smoke Sensor’s operation by performing a self-test when press & hold the Test Button.
Notes:
1. When choosing location of smoke sensor, make sure the alarm sound can be easily audible in other rooms in the building.
2. It’s recommended to install the sensor in already decorated, painted rooms and at least 1,5m from air conditioners.
3. Do not install the sensor in direct sunlight. Keep at least 0.5m distance from light sources. Do not install the sensor in places
prone to drafts. Do not install the sensor in places with high water vapor condensation, e.g. above stoves, ovens, kettles, etc.
4. The device can not be installed in places where the temperature exceeds operational values (0 o C - 55 o C).
5. The low battery status will be checked and reported per hour.
TO return your device to factory default:
Use certificated controller to remove device from network will reset it to factory default.
Please use this procedure only in the event that the network primary controller is missing or otherwise inoperable.
Adding to Z-Wave network
1) Install the battery. Visual indicator show status (red - device ready for adding, green - device added),
please remove device from Z-Wave network
firstly.
2) Make sure the device is located within direct range of the Z-Wave controller.
3) Follow the instructions of certified controller to include a device from different manufactures into the Z-Wave network.
4) Once the controller is ready to include your device, triple click the ADD Button, located on Smoke Sensor.
5) Smoke Sensor will be detected and added in the Z-Wave network.
Removing from Z-Wave network
Installation
Removing from Z-Wave network
Note:
1. The association group supports five nodes and lifeline function.
2. This product can be operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers. All non-battery
operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.
Smoke Sensor responds to the physical presence of smoke. Smoke presence is required for the device to react. Smoke Sensor
every 10 seconds checks for smoke presence. Once the level of smoke exceeds value set in parameter 1, Smoke Sensor triggers
an alarm. Fire alarm is signaled by sending an appropriate alarm command to devices, the Z-Wave controller and also by an
intermittent sound and visual indicator blinking red. Once the
fire alarm has ceased, the sensor checks whether the smoke has
actually disappeared before getting back to normal operation, i.e. performing a self test each 10 seconds and checking for
presence of smoke.
ZW1103 Smoke Sensor-1pcs
Test Button Close Lock
Screw-2 pcs
CR123A-1pcs
ADD Button
Installation Operation manual-1pcs
Smoke Sensor bottom
Smoke Sensor top without battery
Package content:
-
1
-
2
dans d''autres langues
- English: EVA LOGIK ZW1103 User manual
Autres documents
-
Show Home ZW1201 Manuel utilisateur
-
GE 34193 Manuel utilisateur
-
First Alert ZCOMBO Le manuel du propriétaire
-
-
Fibaro FGMS-001 Mode d'emploi
-
Fibaro FGFS-101 Guide d'installation
-
Fibaro FGSD-002 ZW5 Le manuel du propriétaire
-
-
-
