Philips BT51A/00 Manuel utilisateur
- Catégorie
- Hauts-parleurs portatifs
- Taper
- Manuel utilisateur
Ce manuel convient également à
User manual
1EN
Contents
1 Important 2
2 Your portable speaker 3
Introduction 3
What's in the box 3
Overview of the speaker 3
3 Get started 4
Charge the built-in battery 4
Turn on/off 4
4 Play from Bluetooth devices 5
Connect a device 5
Disconnect a device 5
Reconnect a device 6
5 Play from external devices 7
6 Product information 8
$PSOLÀHU
Speaker 8
Bluetooth 8
General information 8
7 Troubleshooting 9
General 9
About Bluetooth device 9
8 Notice 10
Compliance 10
Care of the environment 10
Trademark notice 10
2 EN
1 Important
Warning
•
Never remove the casing of this product.
• Never lubricate any part of this product.
• Never place this product on other electrical equipment.
• Keep this product away from direct sunlight, naked
ÁDPHVRUKHDW
• Read these instructions.
• Heed all warnings.
• Follow all instructions.
• Do not use this apparatus near water.
• Do not install near any heat sources such
as radiators, heat registers, stoves, or
RWKHUDSSDUDWXVLQFOXGLQJDPSOLÀHUVWKDW
produce heat.
• 2QO\XVHDWWDFKPHQWVDFFHVVRULHVVSHFLÀHG
by the manufacturer.
• 5HIHUDOOVHUYLFLQJWRTXDOLÀHGVHUYLFH
personnel. Servicing is required when
the apparatus has been damaged in any
way, such as liquid has been spilled or
objects have fallen into the apparatus, the
apparatus has been exposed to rain or
moisture, does not operate normally, or
has been dropped.
• The battery shall not be exposed to
H[FHVVLYHKHDWVXFKDVVXQVKLQHÀUHRUWKH
like.
• Apparatus shall not be exposed to
dripping or splashing.
• Do not place any sources of danger on the
DSSDUDWXVHJOLTXLGÀOOHGREMHFWVOLJKWHG
FDQGOHV
Note
•
The type plate is located on the bottom of the
apparatus.
Your portable
speaker
Congratulations on your purchase, and
welcome to Philips!Tofully
from the
support that Philips offers, register your product
at www.philips.com/welcome.
Introduction
With this speaker, you can enjoy audio from
Bluetooth-enabled devices or other external
devices.
What's in the box
Check and identify the contents of your
package:
Speaker
USB cable for charging
Short user manual
Safety & notice
Overview of the speaker
1 LED indicator
Indicate battery or Bluetooth
connection status.
2 Source selector (OFF/ ON)
Select Bluetooth source.
Turn the speaker off.
3 PAIRING
Enter Bluetooth pairing mode.
Disconnect Bluetooth connection.
4 DC IN
Recharge the built-in battery.
13
4
2
EN
3 Get started
Always follow the instructions in this chapter in
sequence.
Charge the built-in battery
The speaker is powered by a built-in
rechargeable battery.
Note
Before use, fully charge the built-in battery.
The micro USB socket is for charging only.
It takes you approximately two hours to fully charge
the battery.
Rechargeable battery has a limited number of charge
cycles. Battery life and number of charge cycles vary by
use and settings.
Connect the USB cable between
the DC IN socket on the speaker, and
a USB socket on a computer.
The LED indicator indicates the battery status.
Under charging Fully charged
OFF
mode
Flashing white Off
Bluetooth
mode
Flashing blue
or solid blue
(depending
on Bluetooth
connection
status)
Flashing blue
or solid blue
(depending
on Bluetooth
connection
status)
Turn on/off
To turn the speaker on, slide the source
selector to
To turn the speaker off, slide the source
selector to OFF
Switch to standby mode
The speaker switches to standby mode
automatically in the following situations:
In Bluetooth mode, the connection with
Bluetooth device is invalid for 15 minutes;
or
4 Play from
Bluetooth
devices
With this speaker, you can listen to audio from
Bluetooth-enabled devices.
The speaker can memorize a maximum of four paired
devices. The
paired device will replace the one.
Any obstacle between this speaker and a Bluetooth
device can reduce the operational range.
Keep away from any other electronic device that may
cause interference.
The operational range between this speaker and a
Bluetooth device is approximately 10 meters (30 feet).
Make sure that no audio input cable is connected to
the AUDIO IN socket.
Connect a device
Slide the source selector to
» The LED indicator blue.
2 On your Bluetooth device, enable
Bluetooth and search for Bluetooth devices
that can be paired (refer to the user
manual of the device).
3 Select [Philips BT51] displayed on your
device for pairing and connection. If
necessary, input “0000” as the pairing
password.
» After successful pairing and connection,
the speaker beeps twice, and the LED
indicator turns solid blue.
If you cannot
[Philips BT51] on
your device, press and hold PAIRING
for more than three seconds until you
hear triple beeps.
4 Play Bluetooth device.
You can use your Bluetooth device to control play.
LED indicator (blue)
Indicator Bluetooth connection status
Fast
(2Hz) Pairing
Slow
(1Hz) Connecting
Solid blue Connected
Disconnect a device
Press and hold PAIRING for more than
three seconds;
» The speaker beeps for three times.
Disable Bluetooth on your device; or
Move the device beyond the
communication range.
» The speaker beeps twice, and the LED
indicator
blue.
Before connecting another Bluetooth device, disconnect
the current device
Reconnect a device
When you turn on the speaker, it will reconnect
the last connected device automatically; If not,
select [Philips BT51] on your Bluetooth device
to start connection.
1
1
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
Philips BT51A/00 Manuel utilisateur
- Catégorie
- Hauts-parleurs portatifs
- Taper
- Manuel utilisateur
- Ce manuel convient également à
dans d''autres langues
- English: Philips BT51A/00 User manual
Documents connexes
-
Philips TAS1505 Manuel utilisateur
-
-
-
-
-
-
-
-
Philips BT50G/37 Guide de démarrage rapide
-