Extron DTP T MK 4K 331 Manuel utilisateur

Extron
Marque
Extron
Modèle
DTP T MK 4K 331
Taper
Manuel utilisateur

Ce manuel convient également à

1
IMPORTANT:
Go to www.extron.com for the complete
user guide, installation instructions, and
specifications bef
ore connecting the
pr
oduct to the po
wer source.
DTP T EU 4K and DTP T MK 4K • Setup Guide
This guide provides instructions for a professional installer to install any of the Extron
DTP T EU 4K 331, DTP T EU 4K 231, DTP T MK 4K 331, or DTP T MK 4K 231 transmitters into an EU
or MK one-gang junction box or European cable channel system and to make all connections.
The HDMI transmitters, paired with a compatible receiver, can extend the digital video signal up to 330 feet (100 meters) (DTP T EU 4K 331
and DTP T MK 4K 331) or 230 feet (70 meters) (DTP T EU 4K 231 or DTP T MK 4K 231).
Top
Side
RearFront
HDBT
DTP
HDMI IN
0.7 A MAX
POWER
12V
C
D
B
A
C
B
Figure 1. DTP T EU 4K and DTP T MK 4K Unit Features
Installation
Planning
CAUTION: Failure to check these items may result in personal injury or property damage.
ATTENTION : La non-vérication des éléments listés ci-dessous peut provoquer des blessures ou dommages matériels.
Check that the installation meets the building, electrical, and safety codes.
Ensure there is enough space in the junction box or Euro channel for the DTP transmitter, cables, and rear panel connectors when the
DTP transmitter is completely connected and mounted.
NOTE: The transmitters require 47 mm (1.9”) in the junction box for the device plus cable clearance.
Mounting and Cabling
For additional mounting details and considerations, see the DTP T EU 4K 331, DTP T MK 4K 331, DTP T EU 4K 231, and DTP T MK 4K 231
User Guide at www.extron.com).
Step 1 — Install the junction box or Euro channel
Install the appropriate junction box or Euro channel according to the requirements of the manufacturer (see the manufacturer specications
for more details). This may require creating an opening in the mounting surface. If so, consider the following:
• For accuracy, use the mounting enclosure to mark cut guidelines.
• To avoid making an opening too big, cut inside the marked guidelines.
Rear and Side Panel Features
(Set switch and make connections
before mounting)
Front Panel Features
(Make connections after mounting)
A
TP function switch (see page 2)
B
TP output
C
DC power input
D
HDMI input (see page 3)
2
DTP T EU 4K and DTP T MK 4K • Setup Guide (Continued)
Step 2 — Set the TP function switch and make rear and connections
A
TP function switch (see gure 1 on the previous page) —
DTP
HDBT
If the receiving device is in the Extron DTP series, set this switch to DTP. The TP output consists of HDMI with embedded audio,
analog audio, RS-232 and IR, and remote power over the twisted pair (TP) cable from the receiver.
For an HDBaseT-enabled receiver, set this switch to HDBT position. The TP output consists of HDMI with embedded audio plus
RS-232 and IR. The transmitter and receiver each requires its own 12 VDC power supply.
ATTENTION:
• Position this switch BEFORE connecting the appropriate device to the TP connector. Failure to comply can damage the
endpoint.
• Positionnez le sélecteur AVANT de connecter l’appareil approprié au connecteur TP. Ne pas respecter cette procédure
pourrait endommager le point de connexion.
B
TP Output port — Connect the Out (RJ-45) port to the DTP In port on the receiver.
Extron recommends that you terminate both cable ends in accordance with the following, at a minimum: TIA/EIA T 568B
and 24 AWG, solid conductor, shielded cable with 400 MHz bandwidth.
ATTENTION:
• Do not connect this connector to a computer data or telecommunications network.
• Ne connectez pas ces port à des données informatiques ou à un réseau de télécommunications.
Signal (green) LED — Lights when the device is transmitting a video signal or a test pattern.
Link (yellow) LED — Lights when a valid link between a DTP or HDBT input and output is established.
C
Power — When the TP function switch is in the DTP position, this connector is probably not necessary. The connected
0.7 A MAX
POWER
12V
receiving device can power the transmitter via the TP cable.
If the TP function switch (see figure 1, on the previous page and
A
, above) is in the HDBT position, or if otherwise desired,
plug an optional external 12 VDC power supply into this 2-pole direct insertion connector. See the DTP T EU 4K 331,
DTP T MK 4K 331, DTP T EU 4K 231, and DTP T MK 4K 231 User Guide, available at
www.extron.com, for wiring instructions and important safety considerations.
Step 3 — Install the transmitter to a junction box
ATTENTION:
• Ensure that the junction box is grounded properly.
• Assurez vous que le boîtier d’encastrement est correctement mis à la terre.
NOTE: Removal of the module is difficult after the module has been installed in the bezel
frame. Ensure that all connections are correct BEFORE snapping the module in place.
Mount the transmitter to a junction box as follows:
a. Disconnect power from all devices at the source.
b. Orient the mounting bracket as appropriate for your transmitter (see gure 2, at right):
MK mounting — The word “Front” engraved on the bracket reads vertically.
EU mounting — “Front” reads horizontally.
c. Fasten the provided metal mounting bracket to the mounted junction box, in the proper
orientation, using the two included screws.
NOTES:
• To keep the transmitter securely in place and prevent it from being easily pulled
from its mounting surface, ensure that the side of the bracket with the word
“Front” engraved on it faces out (away from the junction box).
• If you want to be able to remove the transmitter easily from its mounting, attach
the mounting bracket with “Front” facing inward, toward the junction box.
d. Run the TP cable and optional power cable through the junction box and the plastic bezel
frame.
e. Set the TP function switch (
A
) to the appropriate position.
f. Connect the rear panel cables to the transmitter.
Figure 2. Installation
EU Mounting Bracket
EU Wall Box
Bezel Frame
DTP T EU
MK Mounting Bracket
EU Mounting
MK Mounting
MK Wall Box
B
l
F
ra
m
3
g. Align the bezel frame to the metal mounting bracket on the mounting surface.
h. Holding the bezel frame in place on the bracket, press the transmitter into the frame until the unit snaps into place and all four tabs on
the unit snap into their slots.
Step 4 — Make front panel (input) connection
D
HDMI input port (see gure 1 on page 1) — Connect an HDMI cable between this port and the HDMI output port of the
HDMI IN
digital video source.
Operation
After all connected devices are connected and powered on, the system is fully operational. If any issues arise, verify that the cables are
routed and connected properly and that the display device has a compatible resolution and refresh rate. If problems persist, call the Extron
S3 Sales & Technical Support Hotline. See the contact numbers on the last page of this guide for the Extron ofce nearest you.
Application Diagram
LR
POWER
12V
0.7A MAX
AUDIO
SIG LINK
DTP IN
OUTPUTS
LR
POWER
12V
0.7A MAX
AUDIO
SIG LINK
DTP IN
OUTPUTS
DTP HDMI 330 Rx
OVER DTP
RS-232
IR
Tx Rx Tx RxG
DTP HDMI 330 Rx
OVER DTP
RS-232
IR
Tx Rx Tx RxG
50-60 Hz
100-240V ~ -- A MAX
SIG LINK
OUT
1
1 2 3 4 5 6
2 3A 4A
4B 4
RS-232 IR
RS-232 IR
Tx Rx Tx RxG
Tx Rx Tx Rx
XTP
RESET
R
S/PDIF
OUT
DTP
XTP
DTP
XTP
DTP
XTP
DTP
+48V
MIC/LINE
1
1
3
2
4
2
3
4
LINK
EXP
HDBT
HDBT
G
7
8
DTP CROSSPOINT 84 4K
RS-232 IR
Tx Rx Tx RxG
OVER TP
OVER TP
SIG LINK
IN
SIG LINK
IN
AUDIO OUTPUTS
AUDIO INPUTS
DMP EXPANSION
CONTROL
AMP OUTPUT
INPUTS
OUTPUTS
SIG LINK
OUT
3B
RS-232 IR
Tx Rx
RTSCTS
G
1
LR
1
LR
3
LR
3
LR
5
LR
2
LR
4
LR
2
LR
4
LR
6
LR
Tx Rx G
12
12
SGSG
C
34C+V
PWR OUT = 6W
+V D-S+S
Tx Rx G Tx Rx G1234G
REMOTE
COM 1 COM 3COM 2 DIGITAL I/O
LAN 1
LAN 2 LAN 3
CLASS 2 WIRING
1
LR
8Ω / 4Ω
IR/SERIAL RELAYS DIGITAL I/O
Extron Extron
Help
System
Off
Display
Room
Control
Off
Mute
Screen
Lighting
December 15, 2013 - 7:58 AM
Audio
Control
Volume
Mute
Tuner
1 2 3
VCRLaptop PC DVD
Doc
Cam
Tuner
On
Channel
Last
Presets
More
Presets
321
654
987
Enter
0
HDMI IN
Extron
DTP T EU 4K 331
DTP Transmitter for
EU-type Junction Boxes
Display
Extron
DTP HDMI
4K 330 Rx
Receiver
RS-232 HDMI
Display
RS-232 HDMI
CATx Cable
up to 330'
(100 m)
CATx Cable
up to 330'
(100 m)
CATx Cable
up to 230'
(70 m)
CATx Cable
up to 330'
(100 m)
Extron
DTP HDMI
4K 230 Rx
Receiver
Ethernet
Ethernet
Audi
o
Audio
Extron
DTP T MK 4K 331
DTP Transmitter for
MK-type Junction Boxes
Inputs
Outputs
AV
Control
Network
Microphones
Extron
DTP CrossPoint 84 4K IPCP SA
Scaling Presentation Matrix Switcher
Extron
SM 26
Surface Mount
Speakers
Extron
TLP Pro 1020T
10" Tabletop TouchLink
Pro Touchpanel
HDMI IN
Figure 3. Typical DTP Transmitter Operation
Figure 2. Installation
4
68-2962-50 Rev. B
08 16
Extron Headquarters
+800.633.9876 Inside USA/Canada Only
Extron USA - West Extron USA - East
+1.714.491.1500 +1.919.850.1000
+1.714.491.1517 FAX +1.919.850.1001 FAX
Extron Europe
+800.3987.6673
Inside Europe Only
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.299.1800
+971.4.299.1880 FAX
Extron Korea
+82.2.3444.1571
+82.2.3444.1575 FAX
Extron India
1800.3070.3777
(Inside India Only)
+91.80.3055.3777
+91.80.3055.3737 FAX
© 2016 Extron Electronics All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com
DTP T EU 4K and DTP T MK 4K • Setup Guide (Continued)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Extron DTP T MK 4K 331 Manuel utilisateur

Extron
Marque
Extron
Modèle
DTP T MK 4K 331
Taper
Manuel utilisateur
Ce manuel convient également à
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes