Marshall JVM210H Le manuel du propriétaire

JVM

2 SERIES

USER MANUAL

ENGLISH

CONGRATULATIONS

ON PURCHASING YOUR

MARSHALL JVM.

THE JVM PRODUCES A BROAD SONIC PALETTE, MAKING IT AN INCREDIBLY

VERSATILE TOOL. IT CAN TAKE YOU FROM CLASSIC CLEAN AND

OVERDRIVEN TONES TO HEAVIER GRUNT AND THEN HIGH GAIN. FULLY

PROGRAMMABLE, THE JVM SERIES HAS UNPRECEDENTED TONAL CONTROL,

WITH THREE MODES PER CHANNEL, INDEPENDENT REVERBS, PARALLEL/

SERIES FX LOOP AND STOMPWARE® FOOTSWITCH TECHNOLOGY.

WE HOPE YOU ENJOY YOUR NEW AMP AS MUCH AS WE HAVE ENJOYED

DESIGNING AND BUILDING IT FOR YOU.

THE MARSHALL TEAM

USER MANUAL

Warning! Safety instructions 3

FCC Compliance Statement 4

Overview and specication 5

Front panel functions 7

Rear panel functions 10

Footswitch 14

Warning: before going any further, make sure

that your amp is compatible with your mains

electricity supply. If you have any doubt, please

seek help from a qualied technician – your

Marshall dealer can help you with this.

MAINS INPUT & FUSE

The specic mains input voltage rating that

your amp has been manufactured for is

indicated on the rear panel of the amp. Your

amp is provided with a detachable mains

(power) lead, which should be connected to the

mains input socket on the rear panel of the amp.

The correct value and type of mains fuse is

specied on the rear panel of the amp. Never

attempt to bypass the fuse or t one of the

incorrect value or type.

Warning: your amp must be switched off and

disconnected from the mains electricity supply

before you check and/or change any fuse.

IMPORTANT SET UP INFORMATION

Follow the start-up procedures below to safely

switch on your amplier. The procedure differs

depending on whether you plan to run your

amplier into speaker cabinets or for silent

recording.

Warning: failure to comply with the following

points may damage your amp.

Using your amp with speaker cabs

1. Make sure the power handling rating of

the speaker cabinet(s) is/are equal to or

higher than the output power of the amp.

Connect the speaker cabinet(s) to the

correct impedance speaker output(s) on

the rear panel.

Note: only use speaker (unscreened)

cables to connect the cabinets.

2. Ensure both the power switch and standby

switch are switched off and set all master

volumes on the front panel to zero.

3. Connect the footswitch cable to the

footswitch and then connect to the

footswitch socket on the rear panel of the

amp.

4. Connect the supplied mains (power) lead

into the mains input on the rear panel rst

and then into an electrical outlet.

5. Plug your guitar into the input jack socket

on the front panel.

6. Turn the front panel power switch on. The

switch will glow red.

7. After waiting a couple of minutes, turn the

standby switch on.

Warning: before you turn the standby switch

on, a (speaker) load must be attached to the

unit. Never use your amp without a (speaker)

load attached when the standby switch is on.

Using your amp for silent recording

When the standby switch is off the amp can

be used without a load for silent recording.

This mode allows you to take a signal from the

preamp section without engaging the output

power section.

1. Ensure both the power switch and standby

switch are switched off.

2. Connect the footswitch cable to the

footswitch and then connect to the

footswitch socket on the rear panel of the

amp.

3. Connect the supplied mains (power) lead

into the mains input on the rear panel rst

and then into an electrical outlet.

4. Plug your guitar into the input jack socket

on the front panel.

5. Turn the front panel power switch on. The

switch will glow red.

6. A signal for recording is available through

the series/parallel FX loop send output jack

and/or the pre-amp out/send output jack.

Warning: always ensure a load is connected

before you switch the standby switch on (to

leave silent recording mode).

TRANSPORTING YOUR EQUIPMENT

Please ensure that your amp is switched

off, unplugged from the mains electricity

supply and all removable cables have been

disconnected from your equipment before

attempting to move it.

Only move the amp on its own; do not attempt

to move it while it is stacked on top of a cabinet

or other equipment.

ENGLISH

1.0

WARNING! SAFETY INSTRUCTIONS

PLEASE READ THIS MANUAL CAREFULLY BEFORE PLUGGING IN. FOLLOW ALL INSTRUCTIONS AND HEED ALL WARNINGS.

ENGLISH

1.1

FCC COMPLIANCE STATEMENT

This device complies with part 15 of the FCC

Rules. Operation is subject to the following two

conditions:

1. This device may not cause harmful

interferance, and

2. This device must accept any interferance

received, including interferance that may

cause undesired operation.

This equipment has been tested and found

to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC rules.

These limits are designed to provide reasonable

protection against harmful interferance in a

residential installation.

This equipment generates, uses and can radiate

frequency energy and, if not installed and used

in accordance with the instructions, may cause

harmful interferance to radio communications.

However, there is no guarantee that

interference will not occur in a particular

installation. If this equipment does cause

harmful interferance to radio or television

reception, which can be determined by

turning the equipment off and on, the user is

encouraged to try to correct the interference

by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the seperation between the

equipment and the receiver.

• Connect the equipment into an outlet on

a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio

/ TV technician for help.

CAUTION: Any changes or modications not

expressly approved by the party responsible

for compliance may void the users authority to

operate the equipment.

This device complies with CAN ICES-3(B)/

NMB-3(B).

2-channel JVM amps boast 3 gain modes giving

you a total of 6 different sounds to choose

from.

The front panel contains dedicated EQ and

gain controls for both the 2 channels, master

and reverb sections. The master section is

comprised of 2 footswitchable master volumes,

plus master resonance and presence controls

that work on both channels. The reverb section

consists of reverb level controls for each

channel.

JVM205H

VALVES

4 x ECC83, 1 x ECC83 (phase splitter) and 2 x

EL34

CHANNELS

2 (multi): Clean/Crunch and OD

POWER

50W

EQUALISATION

Treble, middle, bass, presence and resonance

EFFECTS

Digital reverb

OUTPUTS

5 x 1/4” jack speaker outputs, selectable 16Ω/

8Ω / 4Ω load

Emulated line out (XLR)

MIDI thru

EFFECTS LOOPS

2, 1 x series parallel, 1 x series

JVM210H

VALVES

4 x ECC83, 1 x ECC83 (phase splitter) and 4 x

EL34

CHANNELS

2 (multi): Clean/Crunch and OD

POWER

100W

EQUALISATION

Treble, middle, bass, presence and resonance

EFFECTS

Digital reverb

OUTPUTS

5 x 1/4” jack speaker outputs, selectable 16Ω/

8Ω / 4Ω load

Emulated line out (XLR)

MIDI thru

EFFECTS LOOPS

2, 1 x series parallel, 1 x series

ENGLISH

2.0

OVERVIEW AND SPECIFICATION

2.1

OVERVIEW AND SPECIFICATION

JVM205C

VALVES

4 x ECC83, 1 x ECC83 (phase splitter) and 2 x

EL34

CHANNELS

2 (multi): Clean/Crunch and OD

POWER

50W

EQUALISATION

Treble, middle, bass, presence and resonance

EFFECTS

Digital reverb

SPEAKERS

2 x 12”

1 x Celestion Heritage G12H (8Ω, 80W)

1 x Celestion Vintage (8Ω, 70W)

OUTPUTS

5 x 1/4” jack speaker outputs, selectable 16Ω/

8Ω / 4Ω load

Emulated line out (XLR)

MIDI thru

EFFECTS LOOP

2, 1 x series parallel, 1 x series

JVM210C

VALVES

4 x ECC83, 1 x ECC83 (phase splitter) and 4 x

EL34

CHANNELS

2 (multi): Clean/Crunch and OD

POWER

100W

EQUALISATION

Treble, middle, bass, presence and resonance

EFFECTS

Digital reverb

SPEAKERS

2 x 12”

1 x Celestion Heritage G12H (8Ω, 80W)

1 x Celestion Vintage (8Ω, 70W)

OUTPUTS

5 x 1/4” jack speaker outputs, selectable 16Ω/

8Ω / 4Ω load

Emulated line out (XLR)

MIDI thru

EFFECTS LOOP

2, 1 x series parallel, 1 x series

JVM215C

VALVES

4 x ECC83, 1 x ECC83 (phase splitter) and 2 x

EL34

CHANNELS

2 (multi): Clean/Crunch and OD

POWER

50W

EQUALISATION

Treble, middle, bass, presence and resonance

EFFECTS

Digital reverb

SPEAKERS

1 x 12”

Celestion G12 (8Ω, 150W)

OUTPUTS

5 x 1/4” jack speaker outputs, selectable 16Ω/

8Ω / 4Ω load

Emulated line out (XLR)

MIDI thru

EFFECTS LOOP

2, 1 x series parallel, 1 x series

ENGLISH

3.0

FRONT PANEL FUNCTIONS

JVM205C / JVM210C / JVM215C

12313

414 710

6589111215

JVM205H / JVM210H

1

2 4 146 7 5 8 9 11 10 12

15

3

13

ENGLISH

3.1

FRONT PANEL FUNCTIONS CONTINUED

The front panel is divided into 3 main sections:

channels, reverb and master. Each of the

channels has 3 modes which are differentiated

by the colour of the light in the button used to

change channel. These are green, orange or red

respectively.

1. POWER SWITCH

This turns the amp on and off.

2. STANDBY SWITCH

The standby switch is used in conjunction with

the power switch to warm up the amp before

use. Turn power switch on for 2 minutes before

switching standby on.

Set the standby switch to the off position

during breaks in performances.

Note: when the standby switch is off the amp

can be used without a load for silent recording.

See the ‘Using your amp for silent recording’

start-up procedure for more information.

3. FOOTSWITCH/MIDI PROGRAM SWITCH

This switch has a dual function:

1. Pressing it once will enter ‘footswitch

program’ mode. This is indicated by a solid

red light.

2. Pressing it twice will enter ‘MIDI program’

mode. This is indicated by a blinking red light.

See more information on these modes later in

this manual.

4. FX LOOP SWITCH

Engages/disengages the series/parallel FX loop

for the current channel.

Note: this switch does not affect the power

amp insert / series loop.

CHANNEL SECTION

Pressing a channel button has two functions:

• When pressing in the same channel it

cycles the gain modes: GREEN (lowest

gain level) > ORANGE > RED (highest gain

level)> GREEN etc. Each mode remembers

its own previous FX, reverb and master

settings.

• Coming from a different channel recalls

the last setting in the new selected

channel.

Note: when you leave and then reselect a

channel, it will automatically recall the last

active mode.

13. CLEAN/CRUNCH CHANNEL

Green mode: this is the cleanest of the three

modes. It uses a simple and straightforward

circuit keeping the signal as pure as possible. In

this mode the channel’s volume control is taken

out of circuit. This is the only JVM mode where

this happens.

Orange mode: this mode shares the preamp

topology of the classic Marshall JTM45/1959

‘Plexi’ models but with a bit more gain.

Red mode: with more gain than the orange

mode, this mode is reminiscent of the Marshall

JCM800 2203 amp, a staple of hard rock.

14. OVERDRIVE CHANNEL

Green mode: this is similar to the hot-rodded

JCM800 sound found in the red mode of the

clean/crunch channel. So, you can dial-in two

distinctly different yet similar crunch sounds if

you so wish - one in each channel.

Orange mode: this adds gain to the overdrive

green circuit, resulting in a sound that is perfect

for singing leads and hard rock tones.

Red mode: this mode has the highest amount

of gain, resulting in a fully distorted heavy metal

tone.

REVERB SECTION

The digital reverb is routed in parallel to the

main signal and mixed using a valve. The reverb

does not degrade the direct signal when

engaged and when off it is effectively removed

from the circuit.

10. REVERB SWITCH

Switches the reverb effect on or off for the

current channel.

Note: the reverb switching has been designed

to avoid abrupt cut offs when changing from

channel to channel or switching the reverb off,

so uses a tail that naturally decays.

11. REVERB CONTROL (OVERDRIVE CHANNEL)

Adjusts the level of reverb applied to the

overdrive channel.

12. REVERB CONTROL (CLEAN/CRUNCH

CHANNEL)

Adjusts the level of reverb applied to the clean/

crunch channel.

MASTER SECTION

The master volume controls set the overall

volume of the amp across all channels. Master 1

ENGLISH

and Master 2 can be assigned to any mode and

can be switched back and forth.

5. MASTER 1

Master 1 is used on all channels/modes by

default.

6. MASTER 2

To set a channel/mode to recall master 2, select

the channel and mode, push the master button

to engage master 2 and then switch out of the

mode. When you re-visit the mode, the amp

will automatically recall which master volume

control you were previously using.

7. MASTER SWITCH

Switch between master 1 and master 2 for

different volume settings on the same channel/

mode. The red led in the switch indicates that

master 2 is engaged. The light is off when

master 1 is engaged.

Note: pre-sets stored in the footswitch will

recall whether master 1 or master 2 was

selected. However, it will not recall the previous

level of the master volume control.

3.2

FRONT PANEL FUNCTIONS CONTINUED

9. PRESENCE

Adjusts the high frequencies of the power amp.

Increasing high frequencies adds more bite to

your sound.

8. RESONANCE

Adjusts the low frequencies of the power amp.

Increasing low frequencies adds more bottom

end giving you a fatter sound.

Warning: care should be taken to avoid over

exertion of the speaker cones in high resonance

settings.

Note: both the presence and resonance

controls are power amp controls and therefore

only have effect when playing through a

speaker.

15. INPUT JACK SOCKET

Connect your guitar here using a ¼” jack

instrument cable.

ENGLISH

4.0

REAR PANEL FUNCTIONS

2

43 5 7 8 9 10 11 12 13 146

1

JVM205C / JVM210C / JVM215C

2

34567891011121314 1

JVM205H / JVM210H

ENGLISH

1. POWER INLET

The supplied mains power lead is connected

here. The mains input voltage rating that your

amp has been built for is shown on the rear

panel.

Warning: before powering on, ensure the

amp is compatible with the mains voltage of

the country that the amp is being used in. If

you have any doubt, please get advice from a

qualied person.

2. MAINS FUSE

Protects the amp and mains supply in the event

of a fault. The correct value of mains fuse is

specied on the rear panel.

SERIES/PARALLEL FX LOOP

This is a programmable FX loop located after

the pre-amp, right before the reverb and series

loop circuits. The FX Loop switch engages/

disengages this effects loop.

13. SERIES/PARALLEL FX LOOP: SEND

Connect your external FX equipment here

using a ¼” jack instrument cable.

12. SERIES/PARALLEL FX LOOP: RETURN

Return your signal from external FX equipment

here using a ¼” jack instrument cable.

11. SERIES/PARALLEL FX LOOP: FX LEVEL

Congure the loop for use with either professional

equipment (+4dBu setting) or with guitar level

effects like effects pedals (-10dBV setting).

10. SERIES/PARALLEL FX LOOP: MIX

CONTROL

Control the amount of effect that can be dialled

in with the mix control. When mix is set to wet,

all the signal goes through the external loop,

adding more direct (unprocessed) signal as you

turn it towards dry.

Note: if you do not connect any effect to the

series/parallel effects loop the mix control can

be used as an additional volume control in any

of the channels.

Warning: when mixing the wet and dry

signals the external effects processor’s output

should be congured to remove the direct

(unprocessed) signal. If the amp sounds thin

after connecting an external effect check that

no direct signal is being returned from the

processor’s output.

Note: if the FX loop is on and the mix control

is set to wet without an external processor

connected, the amp will be muted.

ADVANCED USES OF THE SERIES/PARALLEL

EFFECTS LOOP

• To have a tuner output mute the amp,

connect the tuner to the FX send and

select the clean channel. Turn the mix

control to wet and switch the FX loop on.

Store this preset and label it for example

as ‘tuner’. With this conguration it is not

possible to connect any other effect to the

loop.

• As the reverb circuitry is connected after

the parallel loop you can create presets

that affect an external preamp, including

reverb and/or selecting a different master

volume.

• To use a different preamp and combine it

with the JVM channels:

1. Connect the external preamp output to

the parallel loop return and turn the mix

to wet.

2. Connect the external preamp input with a

splitter to the amps input.

POWER AMP INSERT/SERIES LOOP

This is a passive loop connected right before

the master controls. It is a line level loop so it

is recommended to only use high headroom

devices to avoid signal degradation.

9. PRE-AMP OUT/SEND

Connect your external FX equipment here

using a ¼” jack instrument cable.

8. POWER-AMP IN/RETURN

Return your signal from external FX equipment

here using a ¼” jack instrument cable.

Note: you can plug an external preamp into this

return jack to override the JVM preamp section

and use the output power section only. The

Master controls and the emulated line out are

located after the series loop so it is still possible

to use those features when using an external

preamp.

Note: to use two heads simultaneously, the

suggested procedure is to:

1. Connect the ‘master’ head pre-amp out to

the ‘slave’ head power-amp in.

2. Switch the power-amp insert to active in

the ‘slave’ amp.

In order to track the master volume settings in

both heads it is suggested to use MIDI control

with both amps programmed in the same way.

4.1

REAR PANEL FUNCTIONS CONTINUED

ENGLISH

Connect the MIDI in of one of the amps to the

MIDI thru of the other and the pedalboard or

MIDI equipment to the remaining MIDI in.

7. BYPASS SWITCH

Engage/disengage the power amp insert/series

loop. This switch cannot be programmed.

6. EMULATED LINE OUT

This output sends signal to external equipment.

The signal is taken pre-master volume,

processed through a 4x12 speaker cabinet

emulator and electronically balanced.

Note: using the line out does not omit the need

for a load to be connected (unless the amp is in

silent recording mode).

5. FOOTSWITCH

Connect the supplied footswitch using any

standard ¼” jack instrument lead.

Note: using any other type of footswitch rather

than the one supplied will have no effect and

will be ignored by the amp.

14. SPEAKER OUTPUTS

1/4” jack speaker outputs. They are labelled

according to the corresponding cabinet setups:

• 1 x 16 Ohm: connect a 16Ω speaker cab.

• 1 x 8 Ohm / 2 x 16 Ohm: connect a single

8Ω guitar cabinet or two 16Ω cabinets.

• 1 x 4 Ohm / 2 x 8 Ohm: connect a single 4Ω

guitar cabinet or two 8Ω guitar cabinets.

Warning: although the amp has ve speaker

outputs, never attempt to connect more

speakers than rated. The safe combinations are

listed above. Any other speaker conguration

may stress or damage the amp.

4.2

REAR PANEL FUNCTIONS CONTINUED

ENGLISH

Note: the JVM only accepts incoming data and

it is not able to send any MIDI commands.

4. MIDI IN

Connect any external MIDI equipment to the

MIDI In DIN socket.

3. MIDI THRU

A copy of the signal from the MIDI In connector

is available on the MIDI thru socket to allow

daisy chaining of MIDI equipment.

STORING MIDI PRE-SETS

Pressing the ‘Footswitch/MIDI program’ switch

twice puts the amp in MIDI waiting mode.

The indicator light will ash until a valid MIDI

program change command is received.

When the MIDI program is changed and the

command is sent, the amp stores the current

status (Channel + FX + Reverb + Master

Settings) in the MIDI program number

received. It is possible to store up to 128

different MIDI pre-sets.

To exit this status without waiting for incoming

MIDI data press the ‘Footswitch/MIDI

program’ switch again.

Note: by default, the amp is congured to listen

to MIDI channel #1 but it can be changed to

listen to any of the 16 MIDI channels as follows:

1. Switch off both the standby switch and

power switch.

2. Press and hold the footswitch/MIDI

program switch and switch the power

switch on.

3. Release the footswitch/MIDI program

switch. The LED will start to ash.

4. Send any MIDI command using your MIDI

pedalboard or any other MIDI equipment.

The amp will detect which channel came

in and congure itself to listen to that

MIDI channel only. From now on any

MIDI pre-set you had previously stored

will be activated only on the new channel

regardless of what channel you used

before. This allows a fast reconguration

should there be a MIDI conict with any

other outboard equipment.

If you want to exit the MIDI channel selection

without any action press the footswitch/MIDI

program switch while waiting for MIDI data.

5.0

MIDI OPERATION

MIDI IMPLEMENTATION CHART

MANUFACTURER: MARSHALL MODEL: JVM VERSION 1.0 DATE: 02-05-2018

TRANSMITTED RECOGNISED REMARKS

1. BASIC INFORMATION

MIDI CHANNELS N Y (1-16) DEFAULT RECEIVE CHANNEL 1

NOTE NUMBERS N N

PROGRAM CHANGE N Y (0-127) PRESET RECALL

BANK SELECT RESPONSE N

MODES SUPPORTED:

MODE 1: OMNI-ON, POLY N

MODE 2: OMNI-ON, MONO N

MODE 3: OMNI-OFF, POLY N

MODE 4: OMNI-OFF, MONO N

MULTI MODE N

NOTE-ON VELOCITY N N

NOTE-OFF VELOCITY N N

UNIVERSAL SYSTEM EXLUSIVE N N

MANUFACTURER SYSTEM

EXCLUSIVE

N N

2. MIDI TIMING AND SYNCHRONIZATION

MIDI CLOCK N N

ENGLISH

2-channel JVM amps come supplied with a

4-way programmable footswitch which can

be connected to the amp via any standard ¼”

jack instrument cable.

Warning: the supplied footswitch lead is

unscreened and not suitable for guitar.

The footswitch features 5 LEDS marked clean /

crunch, OD, master, reverb & FX. The LEDs for

each of the 2 channels are 3-coloured green,

orange and red. These indicate which channel

and mode is selected, alongside the status of

master, reverb and FX loop.

Each of the individual footswitches has 2

modes of operation:

• Switch store mode: assign any of its 4

switches to instantly recall any front panel

function (channel/mode; reverb on/off;

master volume 1/2 and FX loop on/off).

Note: if a switch is assigned to select a

channel, once it has been activated it can

be used to scroll through the three modes,

just like its respective front panel switch.

• Pre-set store mode: Each switch can

be programmed to instantly call up a

combination of JVM button options to

form a pre-set. This allows you to recall

complete channel setups in any order and

combination.

As the switches can be programmed

independently you can program a mixture of

the above.

Note: all the settings are stored within your

footswitch; this means it can be plugged into

any JVM amp and all your footswitch settings

can be instantly recalled.

PROGRAMMING THE FOOTSWITCH

To enter footswitch program mode, press

the ‘footswitch/MIDI program’ button on

the front panel once. The indicator light will

illuminate. This mode allows you to program the

footswitch.

Note: when the front panel ‘footswitch/MIDI

program’ switch is off, the footswitch will

execute commands the moment the switch is

pressed down. When the footswitch program

mode is active, you can use the amp as normal

with commands executed on release of the

footswitch.

To store the current amp status/sengs to a

footswitch (pre-set store mode):

1. Press the ‘footswitch/MIDI program’

button on the front panel to enter

footswitch program mode (red LED).

2. Press and hold the desired footswitch for

about 3 seconds. The FX footswitch LED

will icker indicating that the pre-set has

been stored.

To store a specic front panel funcon to a

footswitch (switch store mode):

1. Press the footswitch/MIDI program

button on the front panel to enter

footswitch program mode (red LED).

2. Press and hold the desired footswitch.

While holding the footswitch down, in

less than 3 seconds, press the front panel

switch you want to map. The FX footswitch

LED will icker a couple of times indicating

that the switch has been mapped.

Note: the footswitch/MIDI program switch

cannot be assigned to a footswitch.

6.0

FOOTSWITCH

The footswitch can be hot-swapped and

synchronises itself with the amp after

connection. Connect the footswitch lead to the

footswitch side rst and then connect it to the

amp.

ENGLISH

7.0

FACTORY RESET

MIDI RESET

Warning: once the memory is erased it cannot

be recovered.

To erase all the MIDI pre-sets and set the MIDI

reception channel to #1:

1. Ensure the amp is completely turned off.

2. Press and hold clean/crunch channel

switch.

3. Switch the amp on (power switch on, not

standby switch). The 2 channel LEDs will

glow red.

4. Release the switch.

5. To conrm the factory reset press

overdrive mode switch. If you want to

abort, press any other switch.

FOOTSWITCH RESET

Warning: once the memory is erased it cannot

be recovered.

To reset the footswitch to the factory default

status:

1. Unplug the footswitch at any of the cable

sides.

2. Press and hold the switch #4 (right switch).

3. Plug in the footswitch cord.

4. Release the switch and the FX LED will

start blinking.

5. If you want to erase the footswitch

memory press the switch #3. To keep the

memory press either the #1 or #2 switch.

6. Release the switch and the footswitch will

synchronise with the amp.

The factory default is as follows:

FSW #1: clean/crunch mode;

FSW #2: overdrive mode;

FSW #3: master;

FSW #4: reverb.

ENGLISH

WHILST THE INFORMATION CONTAINED HEREIN IS CORRECT AT THE TIME

OF PUBLICATION, DUE TO ITS POLICY OF CONSTANT IMPROVEMENT AND

DEVELOPMENT, MARSHALL AMPLIFICATION PLC RESERVES THE RIGHT TO

ALTER SPECIFICATIONS WITHOUT PRIOR NOTICE.

MARSHALL AMPLIFICATION PLC,

DENBIGH ROAD,

BLETCHLEY, MILTON KEYNES,

MK1 1DQ, ENGLAND.

T: +44 (0) 1908 375411

MARSHALL AMPLIFICATION PLC

REGISTERED IN ENGLAND

REGISTERED NUMBER: 805676

M3311.214 | BOOK-00089-02

JVM

2 SERIES

MANUEL D'UTILISATION

FRANÇAIS

FÉLICITATIONS POUR

L’ACHAT DE VOTRE

AMPLIFICATEUR JVM.

LE JVM PRODUIT UNE VASTE PALETTE SONORE, CE QUI EN FAIT UN OUTIL EXTRÊMEMENT POLYVALENT.

CELA VA DES TONALITÉS CLAIRES ET SATURÉES CLASSIQUES À DES GROGNEMENTS PLUS LOURDS ET

UN GAIN PLUS ÉLEVÉ. ENTIÈREMENT PROGRAMMABLE, LA SÉRIE JVM EST DOTÉE D’UNE COMMANDE

TONALE SANS PRÉCÉDENT, AVEC TROIS MODES PAR CANAL, REVERBS INDÉPENDANTES, BOUCLE

D’EFFETS PARALLÈLE/SÉRIE ET TECHNOLOGIE DE PÉDALIER DE CONTRÔLE STOMPWARE®.

NOUS ESPÉRONS QUE VOUS APPRÉCIEREZ VOTRE NOUVEL AMPLIFICATEUR AUTANT QUE NOUS AVONS

PRIS PLAISIR À LE CONCEVOIR ET LE CONSTRUIRE POUR VOUS.

L’ÉQUIPE MARSHALL

MANUEL D'UTILISATION

Avertissement! Consignes de sécurité 19

FCC Déclaration de conformité 20

Présentation et spécications 21

Fonctions du panneau avant 23

Fonctions du panneau arrière 26

Operation MIDI 29

Pedalier 30

an d’allumer votre amplicateur en toute

sécurité. La procédure varie selon que vous

envisagez d’utiliser votre amplicateur sur

des enceintes de haut-parleur ou pour des

enregistrements muets.

Aenon : le non-respect des points suivants est

susceptible d’endommager votre ampli.

Ulisaon de votre ampli avec des enceintes de

haut-parleur

1. Assurez-vous que la puissance admissible de

(des) l’ (des) enceinte(s) de haut-parleur est

égale ou supérieure à la puissance de sortie

de l’ampli. Raccordez l’ (les) enceinte(s) de

haut-parleur à la (aux) sortie(s) d’impédance

correcte(s) du haut-parleur située(s) sur le

panneau arrière.

Remarque : utilisez uniquement des câbles

(non blindés) de haut-parleur pour raccorder

les enceintes.

2. Assurez-vous que l’interrupteur d’alimentation

et l’interrupteur de veille sont éteints et réglez

tous les volumes principaux situés sur le

panneau avant sur zéro.

3. Raccordez le câble du pédalier au pédalier

puis raccordez à la prise du pédalier située

sur le panneau arrière de l’ampli.

4. Branchez en premier lieu le cordon

Averssement : avant d’aller plus loin, vérier

que votre amplicateur est compatible avec

votre alimentation électrique. En cas de doute,

s’adresser à un technicien qualié ; votre vendeur

Marshall est en mesure de vous conseiller à ce sujet.

ENTRÉE SECTEUR ET FUSIBLE

D’ALIMENTATION

La tension nominale de l’entrée d’alimentation

pour laquelle votre amplicateur est conçu

est indiquée sur le panneau arrière. Votre

amplicateur est fourni avec un cordon

d’alimentation amovible qui doit être branché à la

prise d’entrée d’alimentation située sur le panneau

arrière de votre amplicateur.

La valeur et le type de fusible d’alimentation

appropriés sont spéciés sur le panneau arrière de

l’amplicateur. N’essayez jamais de court-circuiter

le fusible ou d’en utiliser un de valeur ou de type

incorrect.

Aenon : votre amplicateur doit être éteint et

déconnecté du réseau électrique avant de vérier

et/ou de changer un fusible.

INFORMATIONS IMPORTANTES CONCERNANT

L’INSTALLATION :

Suivez les procédures de démarrage ci-dessous

d’alimentation fourni à l’entrée d’alimentation

du panneau arrière, puis ensuite à la prise

électrique.

5. Branchez votre guitare à la prise d’entrée du

panneau avant.

6. Activez l’interrupteur d’alimentation du

panneau avant. Le commutateur devient rouge.

7. Attendez quelques minutes, puis allumez

l’interrupteur de veille.

Aenon : Avant d’allumer l’interrupteur de

veille, une charge (de haut-parleur) doit être xée

à l’unité. N’utilisez jamais votre ampli sans qu’une

charge (de haut-parleur) ne soit xée lorsque

l’interrupteur de veille est allumé.

Ulisaon de votre ampli pour un

enregistrement muet

Lorsque l’interrupteur de veille est éteint,

l’ampli peut être utilisé sans charge pour

un enregistrement muet. Ce mode vous

permet de recevoir un signal de la section du

préamplicateur sans engager la section de

puissance de sortie.

1. Assurez-vous que l’interrupteur

d’alimentation et l’interrupteur de veille sont

éteints.

2. Raccordez le câble du pédalier au pédalier

puis raccordez à la prise du pédalier située

sur le panneau arrière de l’ampli.

3. Branchez en premier lieu le cordon

d’alimentation fourni à l’entrée d’alimentation

du panneau arrière, puis ensuite à la prise

électrique.

4. Branchez votre guitare à la prise d’entrée du

panneau avant.

5. Activez l’interrupteur d’alimentation du

panneau avant. Le commutateur devient rouge.

6. Un signal pour l’enregistrement est

disponible à travers la prise de sortie de la

boucle d’effets parallèle/série et/ou de la

prise de sortie du préamplicateur.

Aenon : veillez toujours à ce qu’une charge

soit raccordée avant d’allumer l’interrupteur de

veille (pour quitter le mode enregistrement muet).

TRANSPORT DE VOTRE ÉQUIPEMENT :

Vérier que votre amplicateur est éteint et

débranché de l’alimentation secteur et que tous

les câbles pouvant être débranchés ont été

déconnectés de l’équipement avant de déplacer

l’amplicateur.

Déplacez l’amplicateur uniquement seul ;

n’essayez pas de le déplacer lorsqu’il

est empilé sur une enceinte ou un autre

équipement.

FRANÇAIS

1.0

AVERTISSEMENT ! CONSIGNES DE SÉCURITÉ

VEUILLEZ LIRE ATTENTIVEMENT CE MANUEL AVANT BRANCHEMENT. SUIVEZ TOUTES LES CONSIGNES ET RESPECTEZ TOUS LES AVERTISSEMENTS.

FRANÇAIS

DÉCLARATION DE CONFORMITÉ

Cet appareil est conforme à la section 15 de

la réglementation de la FCC. L’utilisation est

soumise aux deux conditions suivantes :

1. L’appareil ne doit pas provoquer

d’interférences nuisibles, et

2. L’appareil doit pouvoir supporter toutes

les interférences reçues, notamment celles

susceptibles de gêner son fonctionnement.

L’équipement a été testé et déclaré conforme

aux limites imposées aux appareils numériques

de classe B, conformément à la section 15

de la réglementation de la FCC. Ces limites

sont conçues pour fournir une protection

raisonnable contre les interférences nuisibles

dans une installation résidentielle.

Cependant, rien ne garantit qu’il n’y aura

pas d’interférences dans une installation

particulière. Si l’équipement provoque des

interférences nuisibles à la réception des

signaux de radio ou de télévision, ce qui peut

être déterminé en l’éteignant et en le rallumant,

on encourage l’utilisateur à essayer de corriger

ces interférences par l’un des moyens suivants :

• Réorienter ou déplacer l’antenne de

réception.

• Augmenter la distance entre

• l’équipement et le récepteur.

• Brancher l’équipement sur une prise

d’un circuit différent de celui auquel le

récepteur est connecté.

• Consulter le revendeur ou un technicien

expérimenté en radio / télévision pour

obtenir de l’aide.

ATTENTION : Tout changement

ou modication non expressément

approuvé par l’organisme responsable

de la conformité peut annuler le droit de

l’utilisateur à se servir de l’équipement.

Cet appareil est conforme à la norme

CAN ICES-3(B)/NMB-3(B).

1.1

FCC DÉCLARATION DE CONFORMITÉ

La page est en cours de chargement...

Marshall JVM210H Le manuel du propriétaire

Ce manuel convient également à

Marshall JVM210H Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents