Polk Audio SURROUNDBAR Le manuel du propriétaire

Taper
Le manuel du propriétaire

Ce manuel convient également à

ENGLISH
2 Polk Audio Customer Service 800-377-7655 (Outside USA & Canada: 410-358-3600)
IMPORTANT SAFETY INSTRUCTIONS
T
his product was designed and manufactured to meet strict quality and safety standards.
There are, however, some installation and operation precautions which you should
be particularly aware of.
1. Read Instructions. All the safety and operating instructions should
be read before the system is operated.
2. Retain Instructions. The safety and operating instructions should
b
e retained for future reference.
3
. Heed Warnings. All warnings on the appliances and in the operating
i
nstructions should be adhered to.
4. Follow Instructions. All operating and use instructions should be followed.
5. Cleaning. Unplug the appliance from wall outlet before cleaning. Do not
u
se liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
6
. Attachments. Do not use attachments not recommended by the product
m
anufacturer as they may cause hazards.
7. Water and Moisture. Do not use these appliances near water for example,
near a bath tub, washbowl, kitchen sink, or laundry tub, in a wet basement,
or near a swimming pool, and the like.
8. Accessories. Do not place these appliances on an unstable cart, stand, tripod, bracket,
or table. The audio/video products may fall, causing serious injury to a child or adult,
and serious damage to the products. Use only with a cart, stand, tripod, bracket,
or table recommended by the manufacturer, or sold with the appliances. Any mounting
o
f the appliances should follow the manufacturer’s instructions, and should use mounting
a
ccessories recommended by the manufacturer.
9. Ventilation. Slots and openings in the cabinet are provided for ventilation and to ensure
r
eliable operation of the appliances and to protect them from overheating, and these openings
must not be blocked or covered. The openings should never be blocked by placing the products
on a bed, sofa, rug, or other similar surface. This product should never be placed near or over
a radiator or heat register. This product should not be placed in a built-in installation such
as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions
have been adhered to.
10. Power Sources. This product should be operated only from the type of power source
indicated on the marking labels. If you are not sure of the type of power supply to your
home, consult your appliance dealer or local power company.
11. Grounding or Polarization. This product is equipped with polarized alternating-current
line plugs (plugs having one blade wider than the other). This plug will fit into the power
outlet only one way. This is a safety feature. If you are unable to insert the plug fully into
the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician
to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.
12. Power Cord Protection. Power-supply cord should be routed so that it is not likely to be walked
on or pinched by items placed upon or against it, paying particular attention to cords at plugs,
convenience receptacles, and the point where they exit from the appliances.
13. Lightning. For added protection for this audio/video product during a lightning storm,
or when it is left unattended and unused for long periods of time, unplug it from
the wall outlet and disconnect the antenna or cable system. This will prevent damage
to the product due to lightning and power-line surges.
14. Power Lines. An outside antenna system should not be located in the vicinity of overhead
power lines or other electric light or power circuits, or where it can fall into such power lines
or circuits. When installing an outside antenna system, extreme care should be taken to keep
from touching such power lines or circuits as contact with them might be fatal.
15. Overloading. Do not overload wall outlets and extension cords as this can result
in a risk of fire or electric shock.
16. Object and Liquid Entry. Never push objects of any kind into this product through openings,
as they may touch dangerous voltage points or short out parts that could result in a fire
or electric shock. Never spill liquid of any kind on this audio/video product.
17. Servicing. Do not attempt to service this product yourself, as opening or removing
covers may expose you to dangerous voltage or other hazards. Refer all servicing
to qualified service personnel.
18. Damage Requiring Service. Unplug this product from wall outlets and refer servicing
to qualified service personnel under the following conditions:
a. When the power supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by following the operating
instructions. Adjust only those controls that are covered by the operating
instructions, as an improper adjustment of other controls may result
in damage and will often require extensive work by a qualified technician
t
o restore the product to its normal operation.
e
. If the product has been dropped or the cabinet has been damaged.
f
. When the product exhibits a distinct change in performance this indicates
a need for service.
19. Replacement Parts. When replacement parts are required, be sure the service
t
echnician has used replacement parts specified by the manufacturer or that
t
he parts have the same characteristics as the original part. Unauthorized
s
ubstitutions may result in fire, electric shock or other hazards.
C
AUTION: Danger of EXPLOSION if battery is incorrectly replaced.
Repalce only with the same or equivalent type. (CR2032)
WARNING: Do not expose batteries or battery pack to excessive
heat such as sunshine, fire or the like.
2
0. Safety Check. Upon completion of any service or repairs to this product,
a
sk the service technician to perform safety checks to determine that
the products are in proper operating condition.
21. Carts and Stands. The appliances should be used only with a cart or stand
that is recommended by the manufacturer. An appliance and cart combina-
tion should be moved with care. Quick stops, excessive force, and uneven
surfaces may cause the appliance and cart combination to overturn.
Use caution when moving the cart/apparatus combination to avoid
injury from tip-over.
2
2. This product is not intended for use outdoors.
The CAUTION marks shown here are located on the back of your SurroundBar
®
Speaker System
CAUTION: To prevent electric shock, match
wide blade of plug to wide slot, insert fully.
CAUTION: No naked flame sources, such as
candles, should be placed on the apparatus.
Operation
Operation is subject to the following two conditions:
1) This device may not cause interference, and
2) This device must accept any interference, including interference
that may cause undesired operation of the device.
Product Disposal
Certain international, national and/or local laws and/or regulations may
apply regarding the disposal of this product. For further detailed information,
please contact the retailer where you purchased this product or the Polk
Audio Importer/Distributor in your country. A listing of Polk Audio Importer/
Distributors can be found on the Polk Audio website www.polkaudio.com or
by contacting Polk Audio at: 5601 Metro Drive, Baltimore, Maryland 21215,
USA. Phone: +1-410-358-3600 or 1-800-377-7655.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy, and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that inter-
ference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
ENGLISH
PLEASE TAKE INVENTORY
Please check to ensure you have everything in your Polk Audio
®
SurroundBar
®
Digital One-Step
carton. Inside, you should find:
SurroundBar
Subwoofer
Subwoofer Power Cord
20V Power Supply
6' Digital (Optical) Cable
1
/8" to 1/8" analog cable
1/8" to RCA adapter
Quick Start Guide
Remote Control
Remote Control Programming Guide
Online Registration Card
Important Note: If anything is missing or damaged, or if
your Polk Audio SurroundBar Digital One-Step fails to operate,
please notify your dealer immediately. We recommend keeping
your original carton and packing materials in case you need
to ship the unit in the future.
ABOUT YOUR SURROUNDBAR DIGITAL ONE-STEP
Thank you for choosing the SurroundBar Digital One-Step
from Polk Audio. You’re about to discover how the legendary
Polk Audio sound makes watching TV and movies so much
more exciting. Using a single bar loudspeaker and a wireless
subwoofer, the SurroundBar Digital One-Step produces a wide
soundstage and rich, full sound. Polk Digital Logic
®
offers
spectacular performance and convenience. And theres even
more about the SurroundBar Digital One-Step you’ll enjoy:
Upgrades any flat panel TV audio to a bigger, fuller Polk Audio
home theater sound.
Easy to set up. Out of the box and listening within minutes.
Compact design complements today’s flat panel TVs.
No need for expensive rear speakers, no messy rear wires.
Wireless subwoofer can be placed anywhere
in the room within 50' (15 m) of the SurroundBar.
Dolby
®
Digital equipped for TV, DVD or Blu-Ray
®
players
and gaming consoles.
Polk Digital Logic guarantees the highest level of performance
without complicated setup or calibration.
Continue to use your favorite remote for your bar and TV,
thanks to SmartBar programming that learns your remote.
(Back-up remote included.)
6' (1.8 m) digital optical cable (Toslink) for the absolute easiest
hookup from your TV to the SurroundBar Digital One-Step.
Built-in wall and shelf mounts ensure a wide range
of locating options.
INSIDE YOUR SURROUNDBAR
DIGITAL ONE-STEP CARTON:
Remote Control Programming Guide
Quick Start Guide
SurroundBar
Wireless Subwoofer
20V Power Supply
6' Digital (Optical) Cable
Remote Control
Subwoofer Power Cord
VOL
SUB
SOURCE
MUTE
3
221
1/8" to 1/8" Analog Cable
1/8" to RCA Adapter
1 2 3 4
C
HANNELID
1
2
3
4
CHANNELID
I
mportantNote: The CHANNEL ID switches on both the SurroundBar
a
ndthe subwoofer must be set to the same number.
Notaimportante: Los selectores de identidad de canal (CHANNEL ID)
debenfijarse en el mismo número.
Note:Remove caps prior to inserting cable (recommended hookup only).
Nota:Si es necesario, quite la tapa antes de insertar el cable
(sóloconexión recomendada).
1
2
3
Contents • Contenido
Important Notes • Notas importantes
VOL
SUB
S
OURCE
MUTE
332211
SUB
S
UBVolume Up and Down ( + / – ): Adjusts the volume of the subwoofer.
Subiday bajada de volumen del subwoofer (SUB, + / – ):
Ajustael volumen del subwoofer.
Digital One-Step
Customer Service Hours of Operation: Monday-Friday, 9AM-5:30PM EST polkcs@polkaudio.com 3
BAR CONTROLS
1. LearnPuts the bar into “learning mode” so
you can program it to respond to commands
from your remote control.
2. Source—Changes which input source
you are listening to.
3. Power ( )—Turns on the bar or puts
it in standby mode.
LED—A light that shines green, orange
or red to indicate operating status.
4. Mute—Mutes the sound coming from
the SurroundBar Digital One-Step.
5. Volume Up and Down ( / )—Adjusts
the volume of the SurroundBar Digital One-Step.
6. Power SwitchTurns the bar on or off,
but you can leave it on all the time.
7. Power Connection—The bar power supply connects here.
8. Audio Inputs (Source 1, 2 or 3)—Where you connect
your TV (or other source) to the SurroundBar Digital
One-Step. Use the 6' optical cable (Source 1) or analog
L/R audio cable (Source 2 & 3).
9. Channel ID SwitchSelects the “channel for the wireless
subwoofer signal. Don’t forget to select the same
“channel on the subwoofer.
NOTE: You’ll probably never need to adjust these switches.
If you put more than one SurroundBar Digital One-Step
system in your home, use different channel ID switch
settings so the systems don’t interfere with each other.
BAR LED
NORMAL MODE:
Green SteadyPower is on; all is well.
Red Steady—The bar is in standby mode.
Green Two Blinks—A remote control signal
is received successfully.
Green Slow BlinkingSystem is muted.
Green Fast Blinking (After pressing volume up
button)—You have reached the maximum volume.
Green Fast Blinking (At power up)—The bar and
subwoofer have established a wireless connection.
Orange Fast Blinking (At power up)—The bar and
subwoofer have failed to establish a wireless connection.
LEARNING MODE: (See page 8 for instructions.)
Orange BlinkingThe bar is in learning mode.
Orange Steady—The bar is in learning mode
and a bar button has been selected.
Green Blinking—The bar has successfully
learned a remote control command.
Red BlinkingThe bar has failed to learn
a remote control command.
Red and Orange Blinking—Learned IR codes
have been successfully erased.
1
2
3
4
5
67 8 9
1 2 3 4
CHANNEL ID
F
ACTORY USE ONLY
2.5A
2
0V
1 32
S
OURCE
POWER
O
N
OFF
S
OURCE MUTELEARN
4 Polk Audio Customer Service 800-377-7655 (Outside USA & Canada: 410-358-3600)
SUBWOOFER CONTROLS
1. Channel ID SwitchSelects the “channel for the
wireless subwoofer signal. Dont forget to select
the same “channel” on the bar.
2. Power SwitchTurns the wireless subwoofer on
and off, but you can leave it on all the time if you wish.
3. Power Connection—The subwoofer power
cord connects here.
SUBWOOFER LEDS
A. Link—LED shines green when the subwoofer
is active and communicating with the bar.
B. ProtectShines red when the subwoofer
is in protection.
REMOTE CONTROL
1
. Power ( )—Turns on the bar or puts
it in standby mode.
2. Mute—Mutes the sound coming
from the SurroundBar Digital One-Step.
3. Source 1, 2 or 3—Changes which input
source you are listening to.
4. Volume Up and Down ( + / –)—Adjusts
the volume of the SurroundBar Digital One-Step.
5. SUB Volume Up and Down ( + / –)
Adjusts the volume of the subwoofer.
Specifications
System Power 180 Watts
Dimensions
SurroundBar 3 3/4" H x 31" W x 3" D
(9.53cm x 78.74cm x 7.62cm)
Subwoofer 10" H x 10 1/4" W x 10 3/4" D
(25.4cm x 26.04cm x 27.31cm)
Weight
SurroundBar 4.3 lbs (1.95kg)
Subwoofer 7.8 lbs (3.5kg)
Power Rating
SurroundBar 20 Vdc, 2.5 A
Subwoofer 100V - 240V, 50Hz - 60Hz, 1A
Model SurroundBar Digital One-Step
A
B
1
23
1
2
3
4
LINK
P
ROTECT
C
HANNEL ID
POWER
ON
O
FF
AC INPUT
100V - 240V
50Hz - 60Hz
60W
WARNING
TO REDUCETHE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOTEXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
NO USERSERVICEABLE PARTS INSIDE,REFER SERVICING TO
QUALIFIEDSERVICE PERSONNEL.
CAUTION
RISKOF ELECTRIC SHOCK
DO NOT OPEN
1
2
3
4
L
INK
P
OWER
O
N
O
FF
A
C INPUT
100V - 240V
5
0Hz - 60Hz
6
0W
P
ROTECT
C
HANNEL ID
AVERTISSEMENT
POURRÉDUIRE LES RISQUES D’ÉLECTROCUTION,GARDEZ
C
ET APPAREILÀ L’ABRIDE LA PLUIE ET DE L’HUMIDITÉ.
AUCUNEPIÈCE INTERNE RÉPARABLE PARL’UTILISATEUR.
CONFIERL’ENTRETIEN À UNPERSONNEL QUALIFIÉ.
ATTENTION
RISQUED’ÉLECTROCUTION
NE PAS OUVRIR
T
his device complies with Part15 of the FCC Rules. Operation
|
is subject to the followingtwo conditions: (1) this device may
not cause harmful interference, and (2) this device must accept
any interference received,including interference that may
cause undesired operation.
This Class B digital apparatuscomplies with Canadian ICES-003.
Cet appareil numerique dela classe B est conforme a la norme
NMB-003 du Canada.
Customer Service Hours of Operation: Monday-Friday, 9AM-5:30PM EST polkcs@polkaudio.com 5
12
3
45
WHERE TO LOCATE YOUR BAR
FOR THE BEST SOUND
It’s easy. The bar comes with rubber pads already attached,
so it will sit securely on any flat surface. Just center the bar
under your TV screen. If your TV is housed in a media center,
you can place the bar above the TV.
If your TV is wall mounted, the bar can mount right beneath
it. The bar has built-in keyhole slots that make it easy.
WHERE TO LOCATE YOUR SUBWOOFER
FOR THE BEST SOUND
Your wireless subwoofer is really easy to place and can
go just about anywhere in the room. Plus you don’t have
to worry about connecting wires, because the only wire
you have to plug in is the power cord. And thats it.
Here’s a little trick: If you place
your subwoofer in a corner of
your room, it will reinforce the
subwoofer’s output, making it
sound louder.
Shelf mounted bar sits in front of TV
Wall mounted bar
6 Polk Audio Customer Service 800-377-7655 (Outside USA & Canada: 410-358-3600)
2
1
2
3
Overall Dimensions
1. 3 3/4" H (9.53cm)
2. 31" W (78.74cm)
Keyhole Slots
3. 16 3/4" W (42.55cm)
HOW TO CONNECT YOUR BAR
This is really easy, too. You probably have two sources
for a signal: your TV or a cable/satellite TV box.
We recommend you use the optical output from your TV
so you can enjoy the highest quality audio for TV and DVD’s.
In the event that your TV does not have an optical output,
you can use the optical output from your cable/satellite box
and then connect your DVD player using one of the other
SurroundBar Digital One-Step inputs.
HOW TO CONNECT YOUR SUBWOOFER
Your subwoofer receives a wireless audio signal from the bar,
so all you need to do is plug in the power cord. Make sure the
subs Channel ID switch is set to the same number as the bar’s
Channel ID switch. (Both Channel ID switches should be set
to the same number out of the box.)
1 2 3 4
CHANNEL ID
F
ACTORY USE ONLY
2.5A
2
0V
1 32
SOURCE
POWER
ON
OFF
H
EADPHONE
OUTPUT
OPTICAL AUDIO
OUTPUT
TV or Cable/Sat Box
SurroundBar Digital One-Step
1 2 3 4
CHANNEL ID
1
2
3
4
CHANNEL ID
POWER
O
N
OFF
W
ARNING
TOREDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
D
ONOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
NOUSER SERVICEABLE PARTSINSIDE, REFER SERVICING TO
QUALIFIEDSERVICE PERSONNEL.
C
AUTION
RISKOF ELECTRIC SHOCK
D
ONOT OPEN
1
2
3
4
LINK
POWER
ON
OFF
AV INPUT
100V - 240V
50Hz - 60Hz
PROTECT
CHANNEL ID
Customer Service Hours of Operation: Monday-Friday, 9AM-5:30PM EST polkcs@polkaudio.com 7
HOW TO OPTIMIZE THE SOUND
WHEN TV SPEAKERS ARE ON
You should hear sound from the bar. If you don’t, turn up
the volume on the bar using its volume control buttons.
If your bar is connected to your TV, there’s a very good chance
your TV speakers are also playing. It’s impossible to give specific
instructions on how to turn off the speakers for every TV, but
here’s a way to do it that covers many of the TVs out there.
1. On your TV remote control, find a “menu” or “setup button.
2. Press this button. You should see an on-screen menu.
3. Next, look for an option to control audio functions
and select it.
The setting to turn off your TV’s internal speakers should be here.
If you can’t turn off your TV internal speakers, don’t worry.
Your SurroundBar Digital One-Step will make your TV sound much
better.To enjoy the best performance from your bar, you’ll
want it to play louder than your TV. Use the following steps
to adjust the volume balance between your TV and the bar:
1. If necessary, program your bar to respond to the volume
up and down control commands of your TV remote. (See
“HOW TO SETUP A REMOTE CONTROL FOR YOUR
SURROUNDBAR DIGITAL ONE-STEP” on page 9.)
2. Turn your TV volume all the way down using the control
buttons on your TV.
3. Then, using the volume control buttons on your bar,
set the volume to a normal listening level (do not use
the remote control).
After you make these adjustments, your SurroundBar
Digital One-Step should always be louder than your
TV speakers. Then use the TV remote control to adjust
the volume as you normally do.
FINE TUNING YOUR SURROUNDBAR
DIGITAL ONE-STEP
The next thing you’ll want to do is adjust the subwoofer
to blend with your bar. This will ensure the system produces
the best sound.
To set the subwoofers volume, play a variety of source material—
some music, a movie sound track with great special effects,
a movie chapter or a part of a concert in which people are
speaking. Adjust the volume until what you hear sounds
natural to you in your normal viewing location.
8 Polk Audio Customer Service 800-377-7655 (Outside USA & Canada: 410-358-3600)
Customer Service Hours of Operation: Monday-Friday, 9AM-5:30PM EST polkcs@polkaudio.com 9
2
LED
3
5
4
LED
VOL
SOURCELEARN
MUTE
L
ED
Press and hold “LEARN” for 2 seconds, or until LED
blinks orange, then release the “LEARN” button.
1
The SurroundBar is turned on and the LED is solid green.
And you have sound coming from the bar.
Hold TV remote 1' - 2' from SurroundBar.
Press and release Volume Up “ .”
LED turns solid orange.
Blinks orange
Solid orange
LED blinks with
each button press
L
ED
LED blinks green,
then turns solid green
Tap “Volume Up” button on your TVs remote control
4 - 8 times, once per second. Tap, do not hold.
6
VOL
When the LED blinks green quickly for 3 seconds,
the command has been learned. The LED will
become solid green.
1' - 2'
HOW TO SET UP A REMOTE CONTROL
FOR YOUR SURROUNDBAR IHT
SMARTBAR
PROGRAMMING NOTE:
For your SurroundBar to respond to your remote control, you
MUST FIRST program the bar to respond to your television’s
original IR (Infra-Red) remote. An RF (Radio Frequency) remote
will not work. Other remotes (cable, satellite) will work only
after you have programmed the bar to respond to the TV’s
I
R remote.
Programming Instructions: Your SurroundBar IHT is currently
p
rogrammed to respond to the remote control that is included
with the product. However, we strongly recommend programming
the SurroundBar to also respond to your existing remote control
using the steps illustrated below. This will enable you to operate
all of your components using a single remote control. While
programming the SurroundBar, ignore anything that
may be displayed on the TV screen.
Example: To teach your bar the “Volume Up”
command of your remote control:
Verify command works.
Repeat steps 1-6 to program “Volume Down” ( ), Source,
Mute and Power buttons ( ).
Note: If your bar fails to learn certain IR remote codes, the power
LED will blink red. Try erasing any previously programmed codes
(see below) and carefully repeat steps 1-6 above.
Code Erasing Procedure: If you have programmed your
SurroundBar IHT to respond to a remote control and you no longer
want it to do so, erase the codes by pressing the LEARN key for
about two seconds while the unit is in standby mode (power LED
is red). You’ll know that previously learned codes have been
successfully erased when the power LED blinks orange twice.
Note: This procedure removes ALL of your bar’s remote control
programming. If you only need to change the programming for
some of the bar buttons, follow the six steps in the sequence
previously described to redo any previous programming.
The SurroundBar will continue to respond to the provided credit
card remote control.
SUB VOLUME CONTROL ON THE BAR
While unit is on and LED is solid green.
1. Tap LEARN once, LED ( ) turns orange.
2. To adjust sub volume, tap up ( ) or down ( ).
3. To return to master volume, tap LEARN again,
LED ( ) turns green.
NOTE: Bass can also be adjusted with included remote control.
10 Polk Audio Customer Service 800-377-7655 (Outside USA & Canada: 410-358-3600)
TROUBLESHOOTING
The bar does not power on.
Ensure you have plugged the power supply
into a live wall outlet.
Ensure that all components of the power
s
upply are connected properly.
Ensure the power supply is properly connected
to the bar power input.
Ensure the rear panel power switch is in the “on” position.
The subwoofer does not power on.
Ensure the subwoofer is plugged into a live wall outlet.
Ensure the rear panel power switch is in the “on” position.
No sound from the bar.
Check that the TV or cable box is providing a signal.
Check that the bar is receiving power and is turned on.
Turn up the volume of the bar.
Check the input cables to make sure they
are connected securely.
Turn up the volume of your television or cable box.
Check mute status: Is the bar status light slowly blinking
green? If so, press the Mute button on the bar.
Check that the audio format of the input source
is set to PCM 2-channel audio.
No sound from the subwoofer.
See section “Subwoofer does not power on.
Turn up the subwoofer volume control using
the remote control.
Is the bar status light blinking orange fast?
If so, the bar and subwoofer have failed to establish
a wireless connection. Turn off both the bar and subwoofer.
Then turn them back on to re-establish communication.
Ensure the channel ID switches on the bar
and subwoofer are set to the same number.
The sound coming from the bar is distorted.
Check the signal source to ensure the distortion
is not coming from there.
Audio processing (see FAQ’s on page 11)—there
maybe audio processing occurring prior to reaching
the bar. Disable this processing.
B
ass output is not loud enough.
T
urn up the subwoofers volume control using
the remote control.
Place the subwoofer closer to a corner of the room.
Move subwoofer closer to viewing location within the room.
The bar won’t learn my remote control commands.
Carefully follow the programming instructions
on the previous page of this manual.
Hold the remote steady and 1-2 feet from
the front of the bar.
Quickly “tap” the remote button 4 times.
Note: The bar learns almost all IR commands,
but some IR protocols cannot be programmed.
The volume of my television speakers gets louder than
my SurroundBar Digital One-Step system over time.
Turn off your TV speakers per the instructions
on page 8 of this manual.
When the remote control volume button is held down,
your television may change volume levels faster than
the bar. Use the buttons on the bar to adjust the volume
of the bar to the correct balance with the TV speakers.
The subwoofers output is intermittent,
or sounds weak or is distorted.
Is the bar status indicator blinking orange? If so, the bar
and subwoofer have failed to establish a wireless connection.
Turn off both the bar and subwoofer. Then turn them back
on to re-establish communication.
Try changing settings of the channel ID switches
on both the bar and the subwoofer.
The wireless subwoofer could be too far away
from the bar to receive a sufficiently strong signal.
Try moving the subwoofer closer.
Like all wireless devices, your SurroundBar Digital One-Step may be susceptible
to RF interference from such sources as microwave ovens, WiFi computer
systems, video game systems, cordless telephones, blue tooth systems, baby
monitors and other devices. In particular, any devices operating in the 2.4GHz
band may cause intermittent wireless connections between the SurroundBar
Digital One-Step speaker and the subwoofer. It is also possible that your
SurroundBar Digital One-Step System may affect other wireless systems.
For the most part, you can avoid wireless performance problems by physically
separating these devices from your SurroundBar Digital One-Step System.
Maintaining a distance of several feet or more between your SurroundBar
Digital One-Step speaker and any wireless device should prevent any mutual
interference effects. If you do notice any subwoofer signal dropouts take care
to identify the root cause (most commonly having other wireless devices too
close) and resolve accordingly. Any interference effects from a microwave
oven will cease once the oven stops operating and may be resolved on
a long-term basis by increasing the physical distance between your
SurroundBar Digital One-Step System and the microwave oven.
A Note Regarding Wireless Performance:
WARNING: LISTEN CAREFU LLY
Polk Audio loudspeakers and subwoofers are capable of playing at extremely high volume levels,
which could cause serious or permanent hearing damage. Polk Audio, Inc. accepts no liability
for hearing loss, bodily injury or property damage resulting from the misuse of its products.
Keep these guidelines in mind and always use your own good judgment when controlling volume:
You should limit prolonged exposure to volumes that exceed 85 decibels(dB).
Refer to the Occupational Health and Safety Administration (OSHA) guidelines at:
www.osha.gov/dts/osta/otm/noise/standards_more.html.
Customer Service Hours of Operation: Monday-Friday, 9AM-5:30PM EST polkcs@polkaudio.com 11
FAQ’S (FREQUENTLY ASKED QUESTIONS)
My TV does not have an optical output.
How do I connect my audio?
You have several options for connecting your audio:
Use the optical output of your source unit (cable/
satellite box, DVD player, etc.) and connect directly to the
SurroundBar Digital One-Step using the supplied
optical cable.
Use the 1/8" (3.5mm) analog / headphone output
of your TV (if available) and connect directly to the
S
urroundBar Digital One-Step using the supplied
1/8" (3.5mm) to 1/8" (3.5mm) analog cable.
Use the RCA audio outputs (white/red pair) on your TV
(if available) and connect directly to the SurroundBar
Digital One-Step using the supplied 1/8" (3.5mm)
to 1/8" (3.5mm) analog cable and 1/8" (3.5mm)
to RCA adapter.
What if my provided optical cable is too short?
We did our best to provide a cable of adequate length;
however, there might be a few setup instances in which
the cable may be too short. If that is your situation,
your local electronics store will have cables that
meet your required length.
Why am I not hearing any sound from my SurroundBar
Digital One-Step when using the provided (optical) cable?
The SurroundBar Digital One-Step is expecting the
audio to be in Dolby
®
Digital or 2-channel format.
You may need to change your TV or cable/satellite
box audio settings accordingly.
My audio sounds strange and distorted.
Your SurroundBar Digital One-Step requires a clean,
unaltered stereo signal for proper audio performance.
If the sound from your SurroundBar Digital One-Step
is strange or distorted, then check the audio menus
of whatever source(s) are connected to your SurroundBar
Digital One-Step and make sure any audio processing
is turned off.
Why can’t I successfully program the SurroundBar
Digital One-Step to respond to my remote control?
There are many remote control formats, and we have done
our best to make the SurroundBar Digital One-Step compatible
with the most popular brands. However, there are likely some
cases in which the bar will not be able to learn your remote
codes. In this case, please use the remote control provided
with the SurroundBar Digital One-Step product or try
a different universal remote control.
How do I control the SurroundBar Digital One-Step?
There are three ways to control your
SurroundBar Digital One-Step:
Use the touch-sensitive buttons on the front of the bar.
Use the provided remote control.
Program the SurroundBar Digital One-Step to respond
to your existing remote (see included instructions).
My SurroundBar Digital One-Step was responding
to commands, but now it isn’t. What should I do?
In this rare event, simply turn off the power (switch located
on the back of the bar), wait a few seconds, and then turn
the power back on. This should restore control.
How do I erase previously learned remote
control commands?
If you have programmed your SurroundBar Digital One-Step
to respond to a remote control and you no longer want
it to do so, then you can erase the codes by pressing
t
he LEARN key for about two seconds while the unit
is in standby mode (power LED is red). The SurroundBar
Digital One-Step will continue to respond to the provided
credit card remote control.
Can I adjust the subwoofer level control from the bar
keypad if I cannot locate the provided remote control?
Yes. You can control the subwoofer volume from the bar
keypad by tapping the LEARN button prior to using the
volume buttons. When you are done with the adjustment
tap the LEARN button again.
To contact Customer Service:
If you have a question or comment, please feel free to call
us or email us. In North America and Canada, call Polk Audio
Customer Service: 800-377-7655 (M-F 9-5:30 EST) or via email
polkcs@polkaudio.com. Outside the US, call 410-358-3600.
Polk Audio is a DEI Holdings, Inc. Company. Polk Audio, Polk,
The Speaker Specialists, SDA, Polk Digital Logic and SurroundBar
are registered trademarks of Polk Audio, Inc.
Products that have earned the Energy Star
®
are designed to protect
the environment through superior energy efficiency.
Manufactured under license from Dolby Laboratories. Dolby and the
double-D symbol are registered trademarks of Dolby Laboratories.
L
IMITED WARRANTY
Polk Audio, Inc., warrants to the original retail purchaser only. This warranty will terminate
a
utomatically prior to its stated expiration if the original retail purchaser sells or transfers the Product
t
o any other party. Polk Audio, Inc., warrants, to the original retail purchaser only, that the LOUD-
S
PEAKER(S), PASSIVE CROSSOVER COMPONENT(S) and ENCLOSURE on this Polk Audio Loudspeaker
P
roduct will be free from defects in material and workmanship for a period of three (3) years
from the date of original retail purchase from a Polk Audio Authorized Dealer. Furthermore, Polk
Audio, Inc., warrants, to the original retail purchaser only, that any AMPLIFIER OR OTHER ELECTRONIC
COMPONENT that may be included in this Polk Audio Loudspeaker Product will be free from defects
i
n material and workmanship for a period of one (1) year from the date of original retail purchase
f
rom a Polk Audio Authorized Dealer. To allow Polk Audio to offer the best possible warranty service,
p
lease fill out the Product Registration Card(s) and send it to the Factory at the address provided
o
n the Product Registration Card(s) within ten (10) days of the date of original purchase. Defective
Products must be shipped, together with proof of purchase, prepaid insured to the Polk Audio
Authorized Dealer from whom you purchased the Product, or to the Factory at 1 Viper Way, Vista,
California 92081. Products must be shipped in the original shipping container or its equivalent;
i
n any case the risk of loss or damage in transit is to be borne by you.
I
f upon examination at the Factory or Polk Audio Authorized Dealer it is determined that the unit
was defective in materials or workmanship at any time during this Warranty period, Polk Audio
or the Polk Audio Authorized Dealer will, at its option, repair or replace this Product at no additional
charge, except as set forth below. All replaced parts and Products become the property of Polk Audio.
Products replaced or repaired under this warranty will be returned to you, within a reasonable time,
freight prepaid. This warranty does not include service or parts to repair damage caused by accident,
disaster, misuse, abuse, negligence, inadequate packing or shipping procedures, commercial use,
voltage inputs in excess of the rated maximum of the unit, cosmetic appearance of cabinetry not
d
irectly attributable to defect in materials or workmanship, or service, repair, or modification of the
P
roduct which has not been authorized or approved by Polk Audio. This warranty shall terminate
i
f the serial number on the Product has been removed, tampered with or defaced.
This warranty is in lieu of all other expressed Warranties. If this Product is defective in materials
or workmanship as warranted above, your sole remedy shall be repair or replacement as provided
above. In no event will Polk Audio, Inc. be liable to you for any incidental or consequential damages
arising out of the use or inability to use the Product, even if Polk Audio, Inc., or a Polk Audio
Authorized Dealer, has been advised of the possibility of such damages, or for any claim by any other
party. Some states do not allow the exclusion or limitation of consequential damages, so the above
limitation and exclusion may not apply to you. All implied warranties on this Product are limited
to the duration of this expressed Warranty. Some states do not allow limitation on how long
an implied Warranty lasts, so the above limitations may not apply to you. This Warranty gives
you specific legal rights, and you also may have other rights which vary from state to state.
This Warranty applies only to Products purchased in Canada, the United States of America,
its possessions, and U.S. and NATO armed forces exchanges and audio clubs. The Warranty
terms and conditions applicable to Products purchased in other countries are available
from the Polk Audio Authorized Distributors in such countries.
CUSTOMER SERVICE
Thank you for your Polk Audio purchase. If you have a question or comment, please feel
free to call us or email us. In North America and Canada, call Polk Audio Customer Service
800-377-7655 (M-F, 9-5:30 EST) or via email [email protected]. Outside the US,
call 410-358-3600.
G
ARANTIE LIMITÉE
La garantie de Polk Audio, Inc., n’est valide que pour l’acheteur au détail original. La garantie sera
a
utomatiquement annulée avant sa date d’expiration spécifiée si l’acheteur original vend ou transfère
l
e produit à tout autre parti. Polk Audio, Inc., garantit—à l’acheteur au détail original seulement—
q
ue le ou les HAUT-PARLEUR(S), COMPOSANTE(S) DE FILTRE PASSIF et CAISSON(S) de ce produit
P
olk Audio seront exempts de tout défaut attribuable aux pièces d’origine et à la main d’oeuvre pour
une période de Trois (3) ans à partir de la date de l’achat au détail original chez un revendeur agréé
Polk Audio. En outre, Polk Audio, Inc., garantit—à l’acheteur au détail original seulement—
que TOUT AMPLIFICATEUR OU TOUT AUTRE COMPOSANTE ÉLECTRONIQUE qui pourrait faire
p
artie ce produit Polk Audio sera exempt de tout défaut attribuable aux pièces d’origine
e
t à la main d’oeuvre pour une période de un (1) ans à partir de la date de l’achat au détail
o
riginal chez un revendeur agréé Polk Audio. Pour permettre à Polk Audio de vous offrir le meilleur
s
ervice de garantie possible, veuillez enregistrer votre nouveau produit en ligne à l’adresse web:
www.polkaudio.com/registration ou contactez le Service à la Clientèle de Polk au 800-377-7655
aux États-Unis et au Canada l’extérieur des. U.: 410-358-3600) dans les dix (10) jours suivant
la date de l’achat original. Assurez-vous de conserver votre reçu d’achat original. Les produits
d
éfectueux doivent être expédiés, avec une preuve d’achat, francs de port et dûment assurés,
a
u revendeur agréé Polk Audio de qui vous avez acheté le produit, ou à l’usine Polk Audio,
à
l’adresse: 1 Viper Way, Vista, California 92081. Les produits doivent être expédiés dans
leur carton d’expédition original ou dans un contenant équivalent. En tout cas le propriétaire
doit assumer tout risque de perte ou de dommage en transit.
Si, suite à l’examen du produit à l’usine Polk ou chez le marchand agréé Polk Audio, il est déter-
miné que la défectuosité est imputable aux matériaux d’origine ou à la main d’oeuvre au cours
de la période de la garantie spécifiée, Polk Audio ou le revendeur Polk Audio, à sa guise, réparera
ou remplacera le produit sans frais additionnels et selon les conditions décrites ci-dessous. Toute
p
ièce ou produit remplacé devient la propriété de Polk Audio. Les produits réparés ou remplacés
s
ous la garantie vous seront expédiés francs de port dans un délai raisonnable. Cette garantie
n
’inclut pas le service ou les pièces nécessaires à la réparation des dommages provoqués par
accident, désastre, abus, négligence, mode d'expédition ou emballage inadéquat, utilisation
commerciale, tensions supérieures au maximum prescrit pour l’unité, aspect visuel du meuble
non directement attribuable à un défaut de pièces d’origine ou de main d’oeuvre, ou par le service,
la réparation, ou toute modification du produit qui n’a pas été autorisé ou approuvé par Polk Audio.
Cette garantie sera annulée si le numéro de série sur le produit a été enlevé, altéré ou falsifié. Cette
garantie prend préséance sur toutes autres garanties énoncées. Si la défectuosité de ce produit est
imputable aux pièces d’origine ou à la main d’oeuvre selon les conditions de la garantie exprimées
ci-dessus, votre seul recourt sera la réparation ou le remplacement selon les conditions décrites
ci-dessus. Dans aucun cas Polk Audio, Inc. pourra-t-elle être tenue responsable pour tout dommage
accessoire ou indirect causé par l’utilisation ou par l’incapacité d’utilisation du produit, même
si Polk Audio, Inc. ou un revendeur agréé Polk Audio, a été avisé de la possibilité de tel dommage,
ou pour toute réclamation par tout autre parti. Certains états ne permettant pas l’exclusion ou
la limitation des dommages indirects, les limitations et exclusions exprimées ci-dessus pourraient
ne pas s'appliquer dans votre cas. Toutes les garanties tacites sur ce produit sont limitées à la durée
de la garantie énoncée. Certains états ne permettant pas la limitation de la durée d’une garantie
tacite, les limitations ci-dessus pourraient ne pas s’appliquer dans votre cas. Cette garantie vous
accorde des droits légaux spécifiques; vous pourriez également avoir d’autres droits qui pourraient
varier d’état en état.
Cette garantie s’applique seulement aux produits achetés au Canada, aux États-Unis d’Amérique
et ses possessions, et dans les clubs audio et d’échange des forces armées des É.U. et de l’OTAN.
Les modalités et les conditions de garantie applicables aux produits achetés dans d’autres pays
sont disponibles chez les distributeurs agréés Polk Audio établis dans ces pays.
SERVICE À LA CLIENTÈLE
Polk Audio ou contactez le Service à la Clientèle de Polk Audio au 1-800-377-7655 (L-V, 9-17:30,
HNE, Canada et É.-U. seulement). À l’extérieur des É.-U. et du Canada, composez le 410-358-3600.
Vous pouvez aussi nous contacter par courriel à l’adresse: [email protected].
HBP2519A
5601 Metro Drive
Baltimore, MD 21215
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Polk Audio SURROUNDBAR Le manuel du propriétaire

Taper
Le manuel du propriétaire
Ce manuel convient également à

dans d''autres langues