Alfresco AXE-PZA Pizza Oven Plus Manuel utilisateur

Marque: Alfresco

Modèle: AXE-PZA Pizza Oven Plus

Catégorie: Fours

Taper: Manuel utilisateur

Ce manuel convient également à

AXE-PZA

GENERAL SAFETY PRECAUTIONS:

 This instruction manual contains important information necessary for the proper assembly and safe

use of this appliance.

 Read and understand all warnings and instructions before assembling and using this appliance.

 Follow all warnings and instructions when using this appliance.

 If instuctions or parts are missing contact Alfresco™ Gourment Grills.

PRÉCAUTIONS GÉNÉRALES DE SÉCURITÉ:

 Ce manuel d'instructions contient des informations importantes nécessaires pour le bon assem-

blage et l'utilisation sécurisée de cet appareil.

 Lisez et comprenez tous les avertissements et instructions avant d'assembler et d'utiliser cet ap-

pareil.

 Suivez tous les avertissements et instructions lors de l'utilisation de cet appareil.

 Si vous n'avez pas toutes les instructions ou toutes les pieces, contactez Alfresco™ Gourment

Grills.

BEFORE USING THE PIZZA OVEN:

 Ensure that the Pizza oven has been leak tested. (see page 16 & 17)

 Remove any packing material.

 Electrical power requirement is 115 VAC - 50/60 Hz. (a GFCI receptacle is recommended for use).

 Electric power supply must be plugged-in at all times for oven operation; except during any electri-

cal maintenance, non-use periods and storage.

3020914

ALFRESCO™ Gourmet Grills

A division of Superior Equipment Solutions, Inc.

1085 Bixby Drive

City of Industry, CA. 91745

Ph.: (888) 383-8800

Fax: (323) 726-4700

Web: www.alfrescogrills.com

! WARNING

1. DO NOT STORE OR USE GASOLINE OR OTHER

FLAMMABLE LIQUIDS OR VAPORS IN THE VI-

CINITY OF THIS OR ANY OTHER APPLIANCE.

2. AN LP CYLINDER NOT CONNECTED FOR USE

SHALL NOT BE STORED IN THE VICINITY OF

THIS OR ANY OTHER APPLIANCE.

! DANGER

IF YOU SMELL GAS:

1. SHUT OFF GAS TO THE APPLIANCE

2. EXTINGUISH ANY OPEN FLAME.

3. OPEN LID.

4. IF ODOR CONTINUES, KEEP AWAY FROM THE

APPLIANCE AND IMMEDIATELY CALL YOUR

GAS SUPPLIER AND OR FIRE DEPARTMENT.

! AVERTISSEMENT

1. NE PAS ENTREPOSER NI UTILISER DE L’ESSENCE

NI D’AUTRES VAPEURS OU LIQUIDES INFLAMMA-

BLES DANS LE VOISINAGE DE L’APPAREIL, NI DE

TOUT AUTRE APPAREIL.

2. UNE BOUTEILLE DE PROPANE QUI N’EST PAS RAC-

CORDÉE EN VUE DE SON UTILISATION. NE DOIT

PAS ÉTRE ENTREPOSÉE DANS LE VOISINAGE DE

CET APPAREIL OU DE TOUT AUTRE APPAREIL.

! DANGER

S’IL Y A UNE ODEUR DE GAZ:

1. COUPEZ L’ADMISSION DE GAZ DE ‘LAPPARIEL.

2. ÉITENDRE TOUTE FLAME NUE.

3. OUVRIR LE COURVERCLE.

4. SI L’ODEUR PERSISTE, ÉLOIGNEZ-VOUS DE L’APPA-

REIL ET APPELEZ IMMÉDIATEMENT LE FOURNIS-

SEUR DE GAZ OU LE SERVICE D’INCENDIE.

CALIFORNIA PROPOSITION 65 - WARNING

The burning of gas cooking fuel generates toxic by-products, which are on the list of substances which

are known by the State of California to cause cancer or reproductive harm. California law requires

businesses to warn customers of potential exposure to such substances. To minimize exposure to

these substances, always operate this unit according to the use and care manual, ensuring you

provide good ventilation when cooking with gas. This warning is issued pursuant to California Health &

Safety Code Sec. 25249.6

TESTED IN ACCORDANCE WITH: ANSI Z21.89-2013 / CSA 1.18-2013

The Standard for Outdoor Cooking Specialty Gas Appliances.

Installation of this cooking appliance must be made in accordace with local codes. In the absence of local

codes, this unit should be installed in accordance with the National Fuel Gas Code No. Z223.1/ NFPA 54,

Natural Gas and Propane Installation code CSA B149-1 , or Propane Storage and Handling Code

B149.2. All Electrical Components must be electrically grounded in accordance with local codes or in the

absence of local codes with the National Electrical Code ANSI/NFPA 70 or Canadian Electrical code

CSA C22.1

F AVERTISSEMENT

PIÈCES ÉLECTRIQUES ET COMPOSANTS.

DÉBRANCHER TOUS LES BLOCS D'ALIMENTA-

TION ET LES PILES AVANT DE LES RÉPARER.

H AVERTISSEMENT

GAZ INFLAMMABLE

DÉBRANCHER TOUS LES GAZ PROPANE OU

GAZ NATUREL DE CET APPAREIL AVANT DE

PIZZA OVEN SERIAL NUMBER LABEL

F WARNING

ELECTRICAL PARTS AND COMPONENTS

DISCONNECT ALL POWER SUPPLIES AND BATTER-

IES BEFORE SERVICING.

H WARNING

FLAMMABLE GAS

DISCONNECT ALL PROPANE OR NATURAL GAS

SUPPLIES TO THIS UNIT BEFORE SERVICING.

READ THIS CARE AND USE MANUAL CAREFULLY AND COMPLETELY BEFORE USING YOUR

PIZZA OVEN TO REDUCE THE RISK OF FIRE, BURN HAZARD OR OTHER INJURY. KEEP THIS

MANUAL FOR FUTURE REFERENCE.

When properly cared for, your Alfresco™ Pizza Oven will give safe, reliable service for many years.

However, extreme care must be used since the Pizza produces intense heat, which can increase acci-

dent potential. When using this appliance, basic safety practices must be followed, including but not lim-

ited to the following:

 Begin by ensuring proper assembly. A qualified technician should perform all other service.

 Do not repair or replace any part of the pizza oven unless specifically recommended in this manual.

 All other service should be referred to and performed by a qualified technician.

 For personal safety, wear proper apparel while cooking.

 Loose fitting garments or sleeves should never be worn while using this appliance.

 Some synthetic fabrics are highly flammable and should not be worn while cooking.

 Never let clothing, pot holders or other flammable materials come in contact with or too close to any

hot surface until it has cooled down sufficiently. Fabrics may ignite and result in personal injury.

 Use only dry potholders: moist or damp potholders on hot surfaces may cause personal burns from

steam. Do not use a towel or bulky cloth in place of potholders. Do not let potholders touch hot por-

tions of the pizza oven.

 Only certain types of glass, heatproof glass ceramic, earthenware, or other glazed utensils are suita-

ble for oven use. These types of materials may break with sudden temperature changes. Use only on

low or medium heat settings and according to their manufacturer’s directions.

 Grease is flammable. Let hot grease cool before attempting to handle it.

 Avoid letting grease deposits collect on the hearth stone by cleaning the grease often, but never

while the oven is ON or HOT from recent use.

 Do not use aluminum foil to line the hearth stone. This can severely upset temperatures, combustion

and airflow or trap excessive heat in the stone and control area. The result of this can be damaged

knobs, electrical components and increased chance of personal injury.

 Children should not be left alone or unattended in an area where the oven is being used. Never allow

them to sit, stand or play on or around the oven. Do not store items of interest to children around or

below the oven. Never allow children to crawl inside of the built - in structure.

 Do not heat unopened food containers that may cause the container to build- up pressure and burst.

 Protect your hand when opening a hot oven door.

 When lighting a burner, always pay close attention to what you are doing. Be certain you are de-

pressing the correct igniter button labeled for the burner you intend on using.

 When using the oven: do not touch the oven hearth stone, opening archway, doors or door frame

surrounding areas with your bare hands as these areas become extremely hot and could cause

burns. Use only the handles and knobs provided for the operation of the oven

 For proper lighting and performance of the burners keep the ports clean. It is necessary to clean

them periodically for optimum performance. The Infrared burner will only operate in one position and

must mounted correctly for safe operation.

 Clean the oven with caution. Avoid steam burns; do not use a wet sponge or cloth to clean the oven

while it is hot. Some cleaners produce noxious fumes or can ignite when applied to a hot surface.

 INSECT WARNING: Spiders and insects can nest in the burners of this and other outdoor ovens,

and cause the gas to flow from the front of the burner. This is a very dangerous condition, which can

cause a fire to occur behind the valve panel, thereby damaging the oven and making it unsafe to op-

erate. Inspect the oven at least twice a year.

 Be sure all oven controls are turned off and the oven is cool before using any type of aerosol cleaner

on or around the oven. The chemical that produces the spraying action could, in the presence of

heat, ignite or cause metal parts to corrode.

 Do not operate the oven under unprotected combustible construction. Use only in well ventilated are-

as. Do not use in buildings, garages, sheds, breezeways or any enclosed areas.

 Keep the area surrounding the oven free from combustible materials, trash, or combustible fluids and

vapors such as gasoline or charcoal lighter fluids. Do not obstruct the flow of combustion gases and

ventilation airways.

 Keep the back of the oven free and clear from debris.

 If the unit is stored indoors ensure that it is cool. If propane is used, the cylinder must be unhooked

and the propane cylinder stored outside in a well-ventilated area, out of reach of children.

 Never use the oven in windy conditions. If located in a consistently windy area, oceanfront, mountain-

top, etc... a windbreak will be required. Always adhere to the specified clearances.

 Do not use the oven for cooking excessively fatty meats or products, which promote flare-ups.

! WARNING

FOR OUTDOOR USE ONLY

NOT TO BE INSTALLED IN OR

ON RECREATIONAL VEHICLES

AND / OR BOATS.

! WARNING

NEVER USE A DENTED OR

RUSTED LIQUID PROPANE

TANK. SHUT OFF TANK WHEN

NOT IN USE.

! AVERTISSEMENT

POUR UTILISATION À

L'EXTÉRIEUR

NE PAS ÊTRE INSTALLÉ DANS OU

SUR DES VÉHICULES RÉCRÉATIFS

ET / OU DES BATEAUX.

! AVERTISSEMENT

N'UTILISEZ JAMAIS DE RÉSERVOIR

DE PROPANE LIQUIDE BOSSELÉ

OU ROUILLÉ. ÉTEINDRE LE RESER-

VOIR LORSQU'IL N'EST PAS UTILI-

SÉ.

LOCATING AND ASSEMBLING THE PIZZA OVEN:

When determining a suitable location for your Alfresco™ Pizza Oven, take into account concerns

such as exposure to wind, rain, sprinklers, proximity to traffic paths and keeping any gas supply line runs

as short as possible.

Locate the oven only in a well-ventilated area. Never locate the oven in a building, garage, breezeway,

shed or other such enclosed areas without an approved ventilation system. Never locate the oven over,

under or next to unprotected combustible construction. During heavy use or when using wood for

flavoring dishes, the oven will produce a lot of smoke.

CLEARANCES:

TO NON-COMBUSTIBLE CONSTRUCTIONS:

A minimum of 3” clearance from the back of the oven Top Rear Exhaust to non-combustible

construction is required to allow the hot exhaust air to escape freely. (Not applicable to built-in models)

A minimum of 1” clearance around the oven perimeter (bottom section) to non-combustible construction

is required to allow air intake through the bottom of the unit for proper flame combustion.

TO COMBUSTIBLE CONSTRUCTIONS:

A minimum of 12” clearance from the back of the oven Top Rear Exhaust to combustible construction

is required to allow the hot exhaust air to escape freely. This requirement however is not applicable to

built-in models. Built-in models must be built and installed in non-combustible construction without

exceptions.

A minimum of 1” clearance around the oven perimeter (bottom section) to combustible construction is

required to allow air intake through the bottom of the unit for proper combustion. Combustible materials

however, should never touch any exterior surface of the oven.

The Alfresco™ Pizza Oven should never be operated while on top of combustible countertops such

as, Formica®, Corian®, Azure®, Quartz Composite materials including wood, laminates, wood

composites nor countertops with combustible materials, binders or components including finishes such

as oils, lacquer, varnish, shellac, paints or other combustible finishes.

ASSEMBLY:

FREE STANDING MODELS:

Before using your Alfresco™ Pizza Oven, complete the following steps:

1. Remove all packaging materials.

2. Ensure that the IR burner is positioned correctly on it’s orifice, and is fully seated onto its

supports.

3. Install the Hearth Stones, Top radiant stone and back Fire Log with it’s support stand.

4. Make the connection to the gas regulator according to the instructions on pages 10 & 11

for your gas type.

5. Allow a 6” clearance around all sides of oven for proper air movement.

BUILT-IN MODELS:

Before locating your Alfresco™ Pizza Oven into your Non-combustible enclosure, complete the

following steps:

1. Remove all packaging materials.

2. Install your oven built-in top exhaust system and finish all construction required according

to the guidelines provided on pages 12 to 14

3. Ensure that the IR burner is positioned correctly on it’s orifice, and is fully seated onto its

supports.

4. Install the Hearth Stones, Top radiant stone and back Fire Log with it’s support stand.

Make sure the log is pushed completely against the back wall for proper combustion.

5. Make the connection to the gas regulator according to the instructions on pages 10 & 11

for your gas type.

6. To comply with safety and service requirements, main gas shut off valve must be

accessible from the front of the oven without using any tools.

WARNING:

To prevent harm and ensure proper operation of your oven, the IR burner must be properly installed with

respect to the gas orifices. Be certain that the orifice is inserted completely into the burner’s inlet and

that the burner rests firmly on its support. The burner should not rock side-to-side nor top-to-bottom if

properly installed. If excessive burner movement is present, reseat the burner or contact your authorized

service provider.

IMPORTANT ELECTRICAL / GAS INSTRUCTIONS:

 USE ONLY A GROUND FAULT INTERRUPTER (GFI) PROTECTED CIRCUIT WITH THIS UNIT.

 NEVER REMOVE THE GROUNDING PLUG OR USE WITH AN ADAPTER OF 2 PRONGS.

 KEEP CORD AWAY FROM HEATED OVEN SURFACES.

 DO NOT LET THE CORD HANG OVER THE EDGE OF A TABLE OR TOUCH HOT SURFACES.

 DO NOT OPERATE ANY OUTDOOR GAS APPLIANCES WITH A DAMAGE CORD, PLUG, OR AFTER THE APPLIANCE MALFUNCTIONS

OR HAS BEEN DAMAGED IN ANY MANNER. CONTACT THE MANUFACTURER FOR REPAIR.

 TO PROTECT AGAINST ELECTRIC SHOCK, DO NOT IMMERSE CORD OR PLUGS IN WATER OR OTHER LIQUIDS.

 UNPLUG FROM THE OUTLET WHEN NOT IN USE AND BEFORE CLEANING.

 INSPECT THE GAS HOSE BEFORE EACH USE. IF IT IS EVIDENT THAT THERE IS EXCESSIVE ABRASION OR WEAR, OR THE HOSE

IS CUT, IT MUST BE REPLACED PRIOR TO THE UNIT BEING OUT INTO OPERATION. A REPLACEMENT HOSE / REGULATOR WITH A

MINIMUM OF 60,000 BTUH CAPACITY SHOULD BE USED.

 KEEP ANY ELECTRICAL SUPPLY CORD AND FUEL SUPPLY HOSE AWAY FROM ANY HEATED SURFACES.

 ALLOW TO COOL BEFORE PUTTING ON OR TAKING OFF PARTS.

 USE ONLY EXTENSION CORDS WITH A 3 PRONG GROUNDING PLUG, RATED FOR THE POWER OF THE EQUIPMENT, AND AP-

PROVED FOR OUTDOOR USE WITH A W-A MARKING.

! WARNING

INSTRUCTIONS IMPORTANTES D'ÉLECTRICITÉ / GAZ:

 UTILISEZ UN CIRCUIT PROTÉGÉ PAR INTERRUPTEUR DE DÉFAILLANCE À TERRE (GFI) AVEC CETTE UNITÉ.

 NE JAMAIS RETIRER LA FICHE DE TERRE OU UTILISER AVEC UN ADAPTATEUR DE 2 PRONGES.

 GARDEZ LE CORDON DE LA SURFACES CHAUFFANTES.

 NE LAISSEZ PAS LE CORDON PENDANT LE BORD D'UNE TABLE OU TOUCHEZ DES SURFACES CHAUDES.

 NE FONCTIONNEZ PAS DES APPAREILS DE GAZ À L'EXTÉRIEUR AVEC UN CORDON DE DOMMAGE, UNE PLAQUE OU APRÈS LES

MALFUNCTIONS DE L'APPAREIL OU A ÉTÉ ENDOMMAGÉS DE QUELQUE MANIÈRE. CONTACTER LE FABRICANT POUR LA RÉPA-

RATION.

 POUR PROTÉGER CONTRE LES CHOCS ÉLECTRIQUES, NE PAS IMMÉRIR LE CORDON OU LES PLAQUETTES DANS L'EAU OU

D'AUTRES LIQUIDES.

 DÉBRANCHEZ-VOUS DE LA SORTIE QUAND IL N'EST PAS UTILISÉ ET AVANT DE NETTOYER.

 INSPECTER LE TUYAU DE GAZ AVANT CHAQUE UTILISATION. SI IL EST EVIDENT QU'IL YA UNE ABRASION OU UN USAGE EXCES-

SIF, OU QUE LE TUYAU EST COUPÉ, IL DOIT ÊTRE REMPLACÉ AVANT QUE L'UNITÉ EFFECTUERA EN FONCTIONNEMENT. UN

TUYAU / RÉGULATEUR DE REMPLACEMENT AVEC UN MINIMUM DE 60 000 BTUH CAPACITÉ DEVRAIT ÊTRE UTILISÉ.

 GARDEZ TOUT LE CORDON D'ALIMENTATION ÉLECTRIQUE ET LE TUYAU D'ALIMENTATION DE CARBURANT ÉLEVÉ DE TOUTES

SURFACES CHAUFFÉES.

 PERMETT DE REFRIR AVANT DE METTRE EN PLACE OU DE DÉCHARGER DES PIÈCES.

 N'UTILISEZ QUE DES CORDES D'EXTENSION AVEC UNE FICHE DE TERRASSEMENT DE 3 PRONGES, RATÉES POUR LA PUIS-

SANCE DE L'ÉQUIPEMENT, ET APPROUVÉES POUR UNE UTILISATION EXTÉRIEURE AVEC UN MARQUAGE W-A.

! AVERTISSEMENT

HEARTH STONE AND LOG INSTALLATION:

After unpacking the Alfresco™ Pizza Oven and before using for the first time, several items need to

be properly installed for the oven to operate correctly.

The Hearth Stones as well as the Top Stone must be located in the unit along with the Ceramic Log and

it’s support tray. Although these items shown on Figure # 1 can be inserted through the oven main

opening, it is best to insert them by removing the top cover of the oven on countertop ovens installations.

The Arched Front Panel as well as the doors can be re-

moved from the oven to ease installation and cleaning. The

Arch Front Panel has 2 wingnuts (one on each end) and

the door assemblies have 2 wingnuts per side.

To remove these items, simply loosen and remove the

wingnuts that support them.

Additionally, the door hinges can be lifted straight up for

quick access without complete removal of the assembly.

Before installing the Hearth stones, verify that the stone’s

support brackets (rear and center) are properly located in

the oven’s cavity over the Infra-Red (IR) Burner.

The channels simply lock-in into the provided slots at both

ends of the IR Burner cavity. (See figure # 2)

REAR

BRACKET

CENTER

BRACKET

IR BURNER

SLOTS

Figure # 2

BACK WALL SLOT

RIGHT

DOOR

TOP COVER

TOP

STONE

OVEN BODY

CERAMIC LOG

LOG SUPPORT

TRAY

WOOD SMOKER

HEARTH STONES

ARCHED PANEL

LEFT

DOOR

THUMB

NUTS (2)

Figure # 1 Figure # 1

RIGHT HINGE ASSEMBLY

LEFT

HINGE

ASSY.

Once the Hearth Stones are installed inside the oven, the Log Support Tray can be inserted into the

slots that can be found at the bottom of the oven cavity back wall. (See figure # 2).

The Log Support Tray can now rest on top of

the Hearth Stones covering the Log Burner.

The Ceramic Log will rest on top of the Sup-

port Tray and must be pushed all the

way back until it contacts the back

wall.

This is done to ensure that the flames from

the Log Burner wrap around the front of the

Log itself, providing radiant heat.

The Top Stone can be placed from the out-

side to rest on top of the oven cavity within

the locating brackets.

Once all the items are in place, the complete

assembly would look like Figure # 3 on the

right.

GAS CONNECTION—LIQUID PROPANE (LP)

NEVER CONNECT THE PIZZA OVEN TO AN UNREGULATED GAS SUPPLY.

Before proceeding, ensure the oven is fitted for LP gas. Connecting to an improper gas type will result in

poor performance and increased risk of damage or injury. Total gas consumption (per hour) with all

burners set on “HI” is a follows:

 Hearth Burner 21,200 BTUH

 Log Burner 18,900 BTUH

The installation of this appliance must conform with local codes or, in the absence of local codes, to the

national fuel gas code, ANSI Z223.1a-1988. Installation in Canada must be in accordance with the

Standard CAN/ CGA-B149.1 Natural Gas Installation or CAN/CGA-B149.2, Propane Installation Code.

Manifold pressure with LP Operating: 10.0” W.C. Non-operating: 11.2” W.C.

L.P. TANK REQUIREMENTS:

Use only a standard 20 Lbs. (5 Gal.) propane gas cylinder (approx. 12” Ø / 18” tall). The tank must be

installed in the upright position. Do not use a dented or rusty LP tank as it may be hazardous and should

be checked by your LP supplier. Never use a cylinder with a damaged valve.

The LP gas cylinder must be constructed and marked in accordance with the specifications for LP gas

cylinders of the U.S. Department of Transportation (DOT) 4BA, 4BW, and 4E.with an ACME thread/

OPD (over fill protection device) installed.

The cylinder must be provided with a shut off valve terminating in an LP gas supply cylinder valve outlet

specified, as applicable, for connection type QCC1 (CGA-791 or ACME threads) in the standard for com-

pressed gas cylinder valve outlet and inlet connections ANSI/CGA V-1.

TOP COVER

TOP STONE

CERAMIC

LOG

LOG TRAY

IR BURNER

HEARTH

STONES

SUPPORT

CHANNELS

LOG

BURNER

Figure # 3

LP GAS CONNECTION TO LP TANKS:

Your Alfresco™ Pizza Oven for use with LP gas comes equipped with its own regulator, which MUST

NOT be removed. The oven is shipped with high capacity, hose/regulator assembly for connection to a

standard 20 Lb. LP cylinder. The LP gas pressure regulator and hose supplied with this oven must be

used without alteration.

If this assembly needs to be replaced, use only the type specified by Alfresco™ for this appliance.

Pizza ovens require a 60,000 BTUH minimum regulator / hose assembly.

To connect the regulator / hose assembly follow the next steps:

 Locate the regulator and gas connection point in

the rear left side of your Oven unit

 Fasten the hose connection to the 1/2” FPT x

3/8” ODF (flare fitting) connected to the elbow.

(See Figure # 4). It is best to use a wrench of

the appropriate size to fasten this connection.

 Fasten the hose regulator to the LP cylinder by

hand tightening the green connector to the tank

valve until the knob stops rotating and it is fixed

to the cylinder’s valve.

RECOMMENDED APPLIANCE AND CYLINDER PLACEMENT:

The Alfresco™ Pizza Oven should be placed on a non-combustible countertop surface suitable for its

operation. (see page 6 for this information). The LP supply cylinder or tank should never be placed on

the counter next to the oven as radiated heat from the oven could possibly create a hazardous condition

and risk of explosion.

Figure # 4

CONNECTION POINT:

1/2” FPT X 3/8” FLARE

BRASS FITTING ON

TYPICAL LP

GAS TANK

LP REGULATOR AND HOSE

ASSEMBLY (PRESET TO 10” WC)

ELECTRICAL

CORD PLUG

! WARNING

KEEP ANY ELECTRICAL CORD

AND FUEL SUPPLY HOSE AWAY

FROM ANY HEATED SURFACES.

! AVERTISSEMENT

GARDER TOUT LE CORDON ÉLEC-

TRIQUE ET LE TUYAU D'ALIMENTA-

TION DE CARBURANT À L'ÉGARD DE

TOUTES SURFACES CHAUFFANTES.

! CAUTION

THE GAS PRESSURE REGULATOR PROVIDED

WITH THIS APPLIANCE MUST BE USED. RE-

PLACE WITH REGULATOR SES MODEL 220-0280

! MISE EN GARDE

LE RÉGULATEUR DE PRESSION DE GAZ FOURNI DE CE

APPAREIL DOIT ÊTRE UTILISÉ. REMPLACER AVEC LE RÉ-

GULATEUR SES MODÈLE 220-0280

For safety, please note of the following instructions:

1. When the LP cylinder and hose is placed close to the unit, a tripping hazard with the hose or cylin-

der might occur. (see Figure 4a and 4b)

2. The length of the hose and the location of the cylinder needs to such as not to interfere with the

unit operation and if it was to fall to the ground, it will not strike the unit on its downward fall nor

pull the unit sufficiently to cause spillage of liquids / food should the cylinder be tipped in any di-

rection.

3. It is recommended to use a standard 20 lbs. LP cylinder (approx. 12” Ø / 18” tall) designed for va-

por extraction marked in accordance of LP gas cylinders and US Department of Transportation

DOT specifications 4BA, 4BW, and 4E. (also approved under Transport Canada specifications

4BAM, 4BWM, and 4EM when necessary) with an ACME thread/ OPD (over fill protection device)

installed.

4. Connect and disconnect the hose according to the procedure on page 10 and always check for

gas leaks according to the procedure on page 16 & 17.

5. If the Pizza Oven is not in use, the gas must be turned off at the supply cylinder.

6. Storing the Pizza Oven indoors is permissible only if the cylinder is disconnected and removed

from the Pizza Oven.

7. Cylinders must be stored outdoors out of the reach of children and shall not be stored in a build-

ing, garage or any other enclosed area.

8. Only use the pressure regulator and hose supplied with your Pizza Oven. A replacement regulator

and hose assembly can be obtained by contacting Alfresco™ Gourmet Grills.

9. The LP cylinder valve connection as well as the pressure regulator supplied should be attached

according to the diagram on page 10.

10. The LP cylinder should be placed upright for vapor withdrawal only. Never turn the cylinder side-

ways or upside down.

11. The LP cylinder must include a permanent collar to protect the cylinder valve at all times.

12. Do not store a spare gas cylinder under or near this Pizza Oven.

13. Never fill the LP cylinder beyond 80 % full.

14. If instructions 12 and 13 are not followed exactly, a fire causing death or serious injury may occur.

15. Place dust cap on cylinder valve outlet whenever the cylinder is not in use. Only install the type of

dust cap on the cylinder valve outlet that is provided with the cylinder valve. Other types of caps or

plugs may result in leakage of propane.

Figure # 4a

Figure # 4b

COUNTER

ACCESS DOOR

(optional)

COUNTER VENTILATION

(see Note 16 below)

Cylinder placed in

such way that cannot

strike the unit when

falling to the ground.

Cylinder and hose are

placed away from the

hot body of the oven

DO NOT place the

cylinder in such a

way that it could

become a tripping

hazard or if tipped,

the cylinder could

drag the unit and

fall in the ground

while operating.

Although Alfresco™ Gourment Grills does not provide the LP cylinder nor an enclosure for the Pizza

Oven, if one was to be used by the end user, we strongly recommend following the ANSI Z21.89- 2013 /

CSA 1.18-2013 guidelines for proper ventilation requirements when using LP cylinders in an enclosure:

16. An enclosure for an LP gas cylinder shall be ventilated by openings at the level of the cylinder

valve and at floor level. The effectiveness of the opening(s) for purposes of ventilation shall be de-

termined with the LP gas supply cylinder in place.

17. This shall be accompanied by one of the following:

a. One side of the enclosure shall be completely open; or

b. For an enclosure having four sides, a top and a bottom (at least two) ventilation openings at

cylinder valve level shall be provided in the side wall, equally sized, spaced at 180 degrees

(3.14 rad), and unobstructed.

18. Each opening shall have a total free area of not less than ½ in

/lb. (7.1 cm

/kg) of stored fuel ca-

pacity and not less than a total free area of 10 in

(64.5 cm

). Example: 20 Lb. cylinder = 10 in

19. The ventilation opening(s) shall be provided at floor level and shall have a total free area of not less

than ½ in

/lb. (7.1 cm

/kg) of stored fuel capacity and not less than a total free area of 10 in

(64.5

20. If ventilation openings at floor level are in a side wall, there shall be at least two openings. The bot-

tom of the openings shall be at floor level and the upper edge no more than 5 in (127 mm) above

the floor. The openings shall be equally sized, spaced at 180 degrees (3.14 rad) and unobstructed.

21. Every opening shall have minimum dimensions so as to permit the entrance of a 1/8 in (3.2 mm)

diameter rod.

! CAUTION

CYLINDERS MUST BE STORED OUTDOORS IN A

WELL VENTILATED AREA OUT OF THE REACH OF

CHILDREN.

DISCONNECTED LP CYLINDERS MUST HAVE THREADED

VALVE PLUGS TIGHTLY INSTALLED, AND MUST NOT BE

STORED IN A BUILDING, GARAGE OR ANY OTHER ENCLOSED

AREA. THE GAS MUST BE TURNED OFF AT THE SUPPLY CYL-

INDER WHEN THE UNIT IS NOT IN USE. IF THE APPLIANCE IS

STORED INDOORS, THE CYLINDER MUST BE DISCONNECTED

AND REMOVED FROM THE APPLIANCE.

! WARNING

YOUR ALFRESCO™ GOURMET GRILL’S

PRESSURE REGULATOR HAS A MAXI-

MUM INPUT PRESSURE OF 14” WC. (OR

APPROX. .5 PSI) , AND A SAFETY LIMIT

OF 69” WC. (2.5 PSI).

! REGULATOR NOTICE

Exposure to pressures above the safety

limit of 69” WC. will permanently damage

the gas regulator requiring a replacement.

OVER PRESSURE DAMAGE IS NOT

COVERED BY YOUR ALFRESCO

! MISE EN GARDE

LE CYLINDRE DOIT ÊTRE STOCKÉ À L'EXTÉRIEUR

DANS UN ENDROIT BIEN VENTILÉ ET HORS DE LA POR-

TÉE DES ENFANTS.

DÉBRANCHER LES BOUTEILLES DE LP DOIVENT

AVOIR DES BOUCHONS DE VALEUR VISSÉS

HERMÉTIQUEMENT INSTALLÉS, ET NE DOIVENT

PAS ÊTRE STOCKÉS DANS UN BÂTIMENT, GARAGE

OU TOUT AUTRE ESPACE FERMÉ. LE GAZ DOIT

ÊTRE ARRÊTÉ AU NIVEAU DU CYLINDRE D'ALIMEN-

! AVERTISSEMENT

VOTRE RÉGULATEUR DE PRESSION AL-

FRESCO GOURMET GRILLADES A UNE

PRESSION D'ENTRÉE MAXIMALE DE 14"

WC (OU ENVIRON 0,5 PSI), ET UNE LIM-

ITE DE SÉCURITÉ DE 69" WC (2,5 PSI).

LP GAS CONNECTION TO LP PIPED SYSTEMS:

An LP piped system is one with a large central LP tank that feeds the entire household. Those systems

are normally equipped with a high pressure regulator by the large LP tank and low pressure regulators

close to the home.

The gas line connectors must comply with the Standard for Connectors for Outdoor Gas Appliances

and Manufactured Homes, ANSI Z21.75 • CAS 6.27, and suitable for outside installation. The maximum

length of the connection shal be 6 Ft. (1.82 m)

GAS CONNECTION - NATURAL GAS (NG)

NEVER CONNECT THE PIZZA OVEN TO AN UNREGULATED GAS SUPPLY.

Before proceeding, ensure the oven is fitted for natural gas. Connecting to an improper gas type will re-

sult in poor performance and increased risk of damage or injury.

Total gas consumption (per hour) with all burners set on “HI” is a follows:

 Hearth Burner 18,800 BTUH

 Log Burner 22,600 BTUH

The installation of this appliance must conform with local codes or, in the absence of local codes, to the

national fuel gas code, ANSI Z223.1a-1988. Installation in Canada must be in accordance with the

Standard CAN/ CGA-B149.1 Natural Gas Installation or CAN/CGA-B149.2, Propane Installation Code.

Manifold pressure with NG:

Operating: 5.0” W.C. (.14 PSI)

Non-operating: 5.5” W.C. (.16 PSI)

Optimum pressure: 7.0” W.C. (.25 PSI)

NOTE: To ensure proper heating performance of this ap-

pliance, verify that the gas line supply pressure is ade-

quate (7.0” W.C. supply pressure is preferred) to maintain

5” W.C. manifold pressure.

Use a minimum 1/2” Ø Flex Hose to prevent gas starva-

tion. Alternatively, use a 1/2” NPT hard gas pipeline.

(See Figure # 5)

Ensure that the service pipe supplying the oven is fitted

with a shut off valve conveniently positioned and easily ac-

cessible as an emergency gas shutoff.

Your Alfresco™ Pizza Oven for use with Natural Gas

comes equipped with its own regulator which MUST NOT

be removed. If this regulator needs to be replaced use only

the type specified by Alfresco™ for this appliance.

SHUT OFF HAND VALVE

MUST BE LOCATED IN

ACCESSIBLE AREA

INCOMING NG

GAS SUPPLY

1/2” Ø - NG

FLEXIBLE HOSE

Figure # 5

To connect the hose assembly follow the next steps:

 Locate the regulator and gas connection point in the rear left side of your oven unit.

 Fasten the Flex Hose connection to the 1/2” ODF (flare fitting) provided with the oven unit.

(See Figure # 5). When using a 1/2” Ø flexible stainless steel gas hose, do not connect a

hose that is more than 48” in length.

 Alternatively, you can use a 1/2” NPT hard gas pipeline with the appropriate fittings.

COUNTERTOP INSTALLATIONS:

Because of the Alfresco™ Pizza Oven’s unique countertop design, it is possible to install the gas

supply (NG or LP) from a location below the counter. The oven is constructed with an opening at the

bottom heat shield to facilitate connections. (See figure # 6)

Standard connections through the back panel can be converted to bottom connections as follows:

 Removing the (2) 1/4-20 bolt fasteners at the inlet

bracket assembly.

 Rotating down the assembly 90° immediately behind

the back panel so it faces down.

 Removing the exterior electrical cable strain relief.

 Feeding the electrical plug through the back panel

downward.

 Re-installing the 1/4-20 bolt fasteners to secure the

piping assembly.

 Re-installing the appropriate size compression fitting

for a flexible hose connections, or…

 Hard-piping the oven with 1/2” NPT piping.

When considering installing the gas supply through the bottom of a non-combustible countertop, it is

recommended to have a 4” diameter hole located as shown on Figure # 7 for piping and electrical re-

quirements.

The center of the 4” Ø hole should be located 2-1/2” from the back panel and 4” from the right side of

the oven base. Keep in mind the final location, clearance to non- combustible materials and free ex-

haust clearances required for the Pizza Oven when locating such access hole.

BOTTOM

HEAT

SHIELD

Figure # 6

ELECTRICAL

CORD

3/8” OR 1/2”

COMPRESSION

ROTATE DOWN

PIPE ASSEMBLY

CONNECTION

OPENING

1/4-20 BOLTS

FASTENERS

REMOVE EXTERNAL

CABLE STRAIN RELIEF

FEED ELECTRICAL

PLUG THROUGH

BACK WALL AND

POINT DOWN.

GAS CONNECTION

DOWNWARDS

FROM THIS…

… TO THAT.

It is highly recommended that the 4” Ø hole be constructed in such manner as to provide with a 3/8”

raised lip to prevent water or spills on the countertop from falling into the under-counter section.

It is recommended to install an access door such as Alfresco™ AXE-30 double sided doors, in order

to reach the LP Gas Tank or the NG Supply Gas Line shut-off valve as well as the GFCI receptacle to

disconnect power to the Pizza Oven.

Refer to Page 12 for ANSI Z21.89-2013 / CSA 1.18-2013 guidelines for proper ventilation requirements

when using LP cylinders in an enclosure.

BUILT-IN INSTALLATIONS:

The Alfresco™ Pizza oven (BI Model) can be installed directly into

existing or new construction. Built -in units require the use of non

combustible masonry materials for safety.

When installing the Alfresco™ Pizza Oven as a built-in unit, careful

consideration to the materials used must be made. As a general rule,

the materials and construction methods should be the same as the

requirements for an outdoor fireplace while maintaining all local build-

ing codes.

The image on the right, Figure # 8, shows how the Alfresco™

Pizza Oven might look like in a built-in configuration.

Figure # 8

Figure # 7

SEE PROPER CLEARANCES TO COMBUSTIBLE AND

NON-COMBUSTIBLE CONSTRUCTION ON PAGE 6

When building the pizza oven into a non-combustible structure, it is critical to have access to

the bottom of the unit. This is a requirement for service and maintenance as the oven will no

longer be removable from the structure.

Alfresco™ recommends installing an AXE-30 double sided door for service, storage, gas supply and

electrical power access.

The Pizza Oven must rest on two 2” ledges to give it proper support and must have free air intake from

the bottom of the oven as shown on Figure # 9 . The built-in construction should have ample ventilation

under the oven in order to have the proper combustion.

Dimensions shown on Figure # 9 below are shown as reference to aid in the design and planning only.

Refer to page 12 for ANSI Z21.89-2013 / CSA 1.18-2013 guidelines for proper ventilation requirements

when using LP cylinders in an enclosure.

LEAK TESTING:

GENERAL:

Although all gas connections on your Alfresco™ Pizza Oven are leak tested at the factory prior to

shipment, a complete gas tightness check must be performed at the installation site due to possible mis-

handling in shipment, or excessive pressure unknowingly being applied to the unit.

Periodically check the whole system for leaks, or immediately check if the smell of gas is detected.

Figure # 9

AXE-PZA-BI Unit

BEFORE TESTING:

 Make sure that all packing material is removed from the oven.

 Make sure the IR Burner tie-down straps are removed from the oven .

 Do not smoke while leak testing.

 Never leak test with an open flame.

 Make a soap solution of one part liquid detergent and one part water for leak testing purposes.

 Apply the solution to the gas fittings by using a spray bottle, or brush.

 For LP units, always check with a full cylinder.

TO TEST:

 Make sure all control valves are in the “OFF” position.

 Apply the soap solution described above to all fittings.

 Turn the gas supply on.

 Check all connections from the supply line, or LP cylinder up to and including the manifold pipe

assembly.

 Soap bubbles will appear where a leak is present.

 If a leak is present, immediately turn off gas supply, tighten any leaking fittings, turn the gas sup-

ply back on, and recheck.

 If you cannot stop a gas leak turn off the gas supply and call your dealer where you purchased

your oven.

 Do not use the Pizza oven until all connections have been checked and do not leak.

 Only those parts recommended by the manufacturer should be used on the oven.

 Substitution can void the Alfresco™ Pizza Oven’s warranty.

IMPORTANT NOTE:

ALWAYS CHECK FOR LEAKS AFTER EVERY LP TANK CHANGE.

If a leak is present, or if the connection hose shows signs of wear, these conditions must be corrected

prior to using your oven.

Check all gas supply fittings for leaks before each use. It is handy to keep a spray bottle of soapy water

near the shut-off valve of the gas supply line. Spray all the fittings. Bubbles indicate leaks.

OVEN AND ACCENT LIGHTS:

The oven light button is located on the upper left side of the front control

panel. This switch controls both the oven space light as well as the front

panel accent lights directly above the control knobs.

LIGHTING INSTRUCTIONS:

BEFORE LIGHTING LP SYSTEMS:

The pressure regulator (Type QCC1) and hose assembly supplied with the Alfresco™ Pizza Oven

must be used. Never substitute regulators for those supplied with the oven. If a replacement is neces-

sary, contact the factory for proper replacement.

LIGHT FIXTURE

(Located inside the oven)

NG SYSTEMS:

Make sure all connections are properly assembled whether is through the back or under the unit.

TO LIGHT, OPEN THE DOORS. Your Alfresco™ Pizza Oven is equipped with an automatic burner

lighting system. When the knob is pushed and turned, the automatic lighting system is active. The sys-

tem will immediately start the Spiral Hot Surface Igniter and open its safety gas valves when ready.

This system lights up the burners instantly as soon as gas has reached the burners.

Once the burner has been lit, the automatic

lighting system will continue glowing as a

safety measure. If the flame suddenly went

off by heavy wind or lack of fuel (NG or LP

gas) the automatic lighting system will contin-

ue to glow in order to relight the burner.

This is a safety feature that is constantly

monitoring the burner and making sure that

the flame is burning correctly.

(See Figure # 10)

The hearth burner is a very large burner locat-

ed at the bottom of the unit and heats up the

hearth stones by infrared heat as well as con-

vection.

It takes a few minutes for the hearth burner to warm up to operating temperature, thus if turned on and

immediately set to low heat, it will take a substantial amount of time to reach cooking temperatures.

When lighting, always keep your face and body as far away as possible from the burners.

NOTE: If electrical power is interrupted while the unit is operating, the safety gas valves will close within

10 to 30 seconds in order to avoid any gas leaks. The unit will resume operation once the electrical pow-

er has been restored.

TO VERIFY OPERATION OF BOTH BURNERS:

Look straight into the oven cavity for the back Log

Burner, (flames should be directly visible over the log).

The Hearth Burner is visible through the viewing port

(see figure # 10a).

The hearth burner is best viewed downwards at ap-

proximately 45° angle .

! WARNING

DO NOT ATTEMPT TO LIGHT THE

OVEN IF THE ODOR OF GAS IS PRE-

SENT. CALL FOR SERVICE.

! AVERTISSEMENT

N'ESSAYEZ PAS D'ALLUMER LE FOUR

SI L'ODEUR DU GAZ EST PRESENTE.

APPELER LE SERVICE.

PUSH & TURN

TO LIGHT UP

BURNERS

PUSH FOR

LIGHTS

Figure # 10

Figure # 10a

HEARTH BURNER

VIEWPORT

(OR ALTERNATE LIGHTING PORT)

OPEN

DOORS

PREHEATING THE OVEN IR-BURNER:

Preheating the Hearth Stone IR BURNER at maximum is important to allow proper combustion at lower

settings later on as well as speeding up the process of heating up the oven. After lighting the IR BURN-

ER as described before, allow to preheat on “MAX” for 15 minutes before beginning to cook.

Preheat the IR-BURNER first, this will also preheat the Hearth Stone and the oven as a whole.

PREHEATING THE CERAMIC LOG:

Preheating the Ceramic Log is not necessary. The Ceramic log sits directly in the exhaust flue of the

Hearth Stone IR-Burner, therefore it will be already preheated by the time the oven reaches cooking

temperatures.

The Ceramic Log Burner is used to create a blast of hot air and infra red heat to reach searing tempera-

tures very fast. It should not be left on HI setting for long times as it will make the oven very hot beyond

usable cooking temperatures.

NOTE: If the Ceramic Log Burner is left on to provide a warm glow while cooking, please do so at a low

setting with minimal flames.

BURNER ADJUSTMENTS:

NOTE: The Alfresco™ Pizza Oven Burners do not require any primary air-mix adjustment and need

only be checked visually for proper performance and low temperature settings only.

The Alfresco™ Pizza Oven is equipped with adjustable gas valves. These valves can be adjusted for

burner minimum (MIN) settings only.

This procedure can be done by removing the gas adjustment knobs and bezels on the front panel to ex-

pose the valve adjustment screw. (A small blade screw driver is required for this adjustment)

(See Figure # 11)

Figure # 11

KNOB AND BEZEL

REMOVED FROM

PANEL

LOW SETTING

ADJUSTMENT SCREW

LOW HEAT SETTING ADJUSTMENT (LOG BURNER):

NOTE:

THE LOW HEAT SETTING ON YOUR OVEN IS PRESET AT THE FACTORY. ADJUST ONLY IF ALTI-

TUDE OR ENVIRONMENTAL FACTORS ARE CAUSING POOR, LOW HEAT, PERFORMANCE.

ADJUSTMENT STEPS:

1. Follow lighting instructions and set the control knob on “MAX” and allow the burner to preheat for 5

minutes.

2. Turn the control knob to “MIN” and wait for the burner temperature to drop and stabilize.

3. Insert a small flat blade screwdriver into the LOW SETTING screw of the gas valve to begin the

flame height adjustment.

4. Turn counter-clockwise to INCREASE the low heat flame, Clockwise to DECREASE.

5. Adjust the flames so the burner flame is approximately 1” to 1½” in length in the LOW position.

(See Figure # 12)

Even if the flame is set very low, the automatic ignition system and its hot surface igniter will continue

glowing as a safety measure, while allowing the safety gas valves to remain open flowing gas to the

burner.

LOW HEAT SETTING ADJUSTMENT (HEARTH STONE IR-BURNER):

NOTE:

THE LOW HEAT SETTING ON YOUR OVEN IS PRESET AT THE FACTORY. ADJUST ONLY IF ALTI-

TUDE OR ENVIRONMENTAL FACTORS ARE CAUSING POOR, LOW HEAT, PERFORMANCE.

ADJUSTMENT STEPS:

1. Remove the Hearth stone closest to the door in order to view the entire Hearth Burner.

2. Follow lighting instructions and set the control knob on “MAX” and allow the burner to preheat for 5

minutes.

1” ~ 1-1/2”

MAXIMUM

FLAME SIZE

Figure # 12

LOG BURNER LOW

FLAME SETTING

! WARNING

NEVER ADJUST THE BURNER SO LOW

THAT IT MAY GO OUT DURING USE. DO

NOT OPERATE THE OVEN WITH THE LOW

HEAT SCREW REMOVED.

GAS CAN ESCAPE AND CAUSE A

POTENTIALLY HAZARDOUS CONDITION.

! AVERTISSEMENT

NE JAMAIS AJUSTER LE BRÛLEUR SI BAS QU'IL

PEUT S'ÉTEINDRE PENDANT L'UTILISATION.

N'UTILISEZ PAS LE FOUR AVEC LA VIS À

CHALEUR BASSE RETIRÉE.

LE GAZ PEUT S'ÉCHAPPER ET PROVOQUER

UNE CONDITION POTENTIELLEMENT

DANGEREUSE.

La page est en cours de chargement...

Alfresco AXE-PZA Pizza Oven Plus Manuel utilisateur

Marque: Alfresco

Modèle: AXE-PZA Pizza Oven Plus

Catégorie: Fours

Taper: Manuel utilisateur

Ce manuel convient également à

AXE-PZA

Télécharger le PDF

rapport

dans d''autres langues

English: Alfresco AXE-PZA Pizza Oven Plus User manual

Alfresco AXE-PZA Pizza Oven Plus Manuel utilisateur

Ce manuel convient également à

Alfresco AXE-PZA Pizza Oven Plus Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents