deako Smart Plug Include Floor Lamps and String Lights Manuel utilisateur

Marque
deako
Modèle
Smart Plug Include Floor Lamps and String Lights
Taper
Manuel utilisateur
Page 1
•Loads:
oResistive 15A
oIncandescent/Halogen 1000W
oMotor ½ HP
•User Interface
oIndicator LED
oOn/Off button
Figure 1 - Smart Plug Design
Smart Plug User Manual
1. Features
Snowflake is a UL or ETL-listed, Smart Plug for the US and Canadian market.
Model:DS2002
Page 2
Figure 2 - Front View
Figure 3 - Button View
2. Snowflake Electronic Interface Requirements
The electronics in Snowflake includes an AC/DC converter, the ESP32 Module, a relay and the
user interface hardware (two buttons and one LED). The Supplier is responsible for all HW
design and development and Deako is responsible for firmware development. A high-level block
diagram is shown in Figure 4.
Status LED
Button
Page 3
Figure 4 – Snowflake Electronics Block Diagram
The ESP32 WROOM32 Module will sit on a daughter card that interfaces to the main smart plug
board. The daughter card will bring out at least 10 connections from the ESP32 WROOM32
Module to the smart plug PCB.
ESP32
Module
On/Off Pair
LED0
3. Snowflake Specifications
Deako expects the Supplier to create a test plan that demonstrates compliance to these
specifications
Table 1 - Snowflake Specifications
# Spec
Operating temperature 0°C - 40°C
UI surface temperature, max resistive load, max temperature
after equilibrium
<50°C
Maximum Load – Incandescent/Halogen 1000W
Maximum Load – ELV/LED Supplier to provide
spec
Maximum Load – MLV Supplier to provide
spec
Load – Motor ½ HP
Load – General Purpose Supplier to provide
spec
Load – Resistive 15A
UL/ETL Yes
UI 2 Buttons + 1 LED
Radio Combo
Power Consumption with Load in Off State 500mW
Neutral Required Yes
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
3.10
3.11
3.12
3.13
Page 4
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
To assure continued compliance, any changes or modifications not expressly
approved by the party.
Responsible for compliance could void the user’s authority to operate this
equipment. (Example- use only shielded interface cables when connecting to
computer or peripheral devices).
This equipment complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference,
(2) This device must accept any interence received, including interference that may
cause undesired operation.
FCC Radiation Exposure Statement:
The equipment complies with FCC Radiation exposure limits set forth for
uncontrolled enviroment. This equipment should be installed and operated with
minimum distance 20cm between the radiator and your body.
Page 5
IC Statement
- English:
This device contains licence-exempt transmitter(s)/receiver(s) that comply with
Innovation, Science and Economic Development Canada’s licenceexempt
RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference that may
cause undesired operation of the device.
‐French: L’émetteur/récepteurexempt de licence contenu dans le présent appareil
est conforme aux CNR d’Innovation, Sciences et
DéveloppementéconomiqueCanada applicables aux appareils radio exempts de
licence. L'exploitation est autorisée aux deux conditions suivantes:
‐(1) l'appareil ne doit pas produire de brouillage, et
‐(2) l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.
l'appareil numérique du ciem conforme canadien peut ‐ 3 (b) / nmb ‐ 3 (b).
cet appareil est conforme à l'exemption des limites d'évaluation courante dans la
section 2.5 du cnr - 102 et conformité avec rss 102 de l'exposition aux rf, les
utilisateurs peuvent obtenir des données canadiennes sur l'exposition aux champs
rf et la conformité.
L'appareil a été évalué pour répondre aux exigences générales d'exposition aux
radiofréquences. L'appareil peut être utilisé en condition d'exposition portable sans
restriction.
This device complies with ISED RF radiation exposure limits set forth for an
uncontrolled environment.
This device must be installed and operated with a minimum distance of 20 cm
between the radiator and user body.
Le présent appareil doit être installé et exploité à une distance minimale de 20 cm
entre le radiateur et les corps.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

deako Smart Plug Include Floor Lamps and String Lights Manuel utilisateur

Marque
deako
Modèle
Smart Plug Include Floor Lamps and String Lights
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents