Square D SQR62101WHZ Manuel utilisateur

Marque: Square D

Modèle: SQR62101WHZ

Taper: Manuel utilisateur

____________________________________________________________________________________________

SQR62101WHZ Z-Wave Plug-in

FCC ID: 2AUCU-62101Z

Retain for future use.

Features

• Duplex outlets, one outlet is always on, another outlet is Z-Wave controlled.

• Wireless Z-Wave technology creates a mesh network for command and

control interoperability with other Z-Wave compliant controllers and devices.

• Manual and remote ON/OFF control of any lighting or other electrical load

connected to Z-Wave controlled outlet.

• Measure the energy usage of the connected loading on the Z-Wave controlled

outlet, display the actual consumption (in W) and the accumulated power used

(in kWh) in the user interface of the gateway.

NOTE:

• Please refer to the gateway installation manual for energy usage display

and energy measurement features.

SQR44101**Z Z-Wave Plug-in Outlet, Energy Monitoring, 15A 125VAC Specifications

Voltage 125 Vac, 60 Hz

Regular

outlet Current 15A

Controlled

Outlet

Incandescent 1000 W

LED 5A

Standard Ballast 1200VA

Resistive 15A

Motor 1/2 Hp

Operating temperature 32–104°F (0–40°C)

Wireless type Z-Wave (Support S2 and SmartStart)

Wireless frequency 908.40 MHz / 908.42 MHz / 916 MHz

Instruction Bulletin GDE77980_Eng, 07/2020

SQR62101WHZ Z-Wave Plug-in Instruction Bulletin

Precautions

CAUTION

HAZARD OF UNINTENDED USE

This Z-Wave plug-in is intended to be used for non-critical automation activities.

It is not intended to support life, safety, or medical equipment.

Failure to follow these instructions can result in personal injury or

equipment damage.

DANGER

HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH

• Apply appropriate personal protective equipment (PPE) and follow safe

electrical work practices. See NFPA 70E, NOM-029-STPS or CSA Z462 or

local equivalent.

• Don’t touch metal pins during plug in or out.

• Indoor use only.

Failure to follow these instructions will result in death or serious injury.

WARNING

HAZARD OF HEAT AND FIRE DAMAGE

Read all instructions before installation. The manufacturer will not be held

responsible for product damage resulting from not following the instructions.

• Wet hands are strictly prohibited.

• Work strictly according to the rated load.

• Do not continue working after self-disassembly of any nature and damage of

external forces.

Failure to follow these instructions can result in death, injury or

equipment damage.

WARNING: This product can expose you to chemicals including Carbon black, which is

known to the State of California to cause cancer, and Bisphenol A (BPA), which is

known to the State of California to cause birth defects or other reproductive harm. For

more information go to www.P65Warnings.ca.gov.

Instruction Bulletin SQR62101WHZ Z-Wave Plug-in

Installation

Operation

1. Local control:

Press the program button, the appliance or device plugged into Z-Wave controlled

outlet will turn ON or OFF.

NOTE: After a power failure, the Z-Wave controlled outlet returns to the off state.

2. Group control the nodes of association group 2:

Press the program button twice within 1s (the interval between two presses is less

than 0.5s), the deice can turn on/off the other Z-Wave devices in the same

association group.

SQR62101WHZ Z-Wave Plug-in Instruction Bulletin

NOTE: Please refer to association setting for nodes group 2 setup. This requires a

gateway with advanced features and assumes the device is included in a network.

3. Inclusion to a Z-Wave network:

NOTE: The device supports S2-authenticated & S2-unauthenticated inclusion method, It

is highly recommended to only select S2-authenticated or the highest inclusion method

for inclusion, and deselect other methods. This ensures the highest security level during

Z-Wave service. During S2-authenticated inclusion, users may be asked to scan the QR

code or enter a 5-digit pin code attached on the device.

A. SmartStart inclusion: The feature assumes the gateway has implemented

SmartStart. Users could use the APP of the gateway or the gateway camera to scan

the QR code on device or on device package before powering on the device, and

then when the device is powered on, it shall be automatically added to the gateway.

B. Manual inclusion: When the gateway is in adding mode (please refer to the

instruction of the Z-Wave gateway for the operations on gateway itself), press the

program button 3 times within 1.5s (the interval between each press is less than

0.5s).

4. Exclusion from a Z-Wave network: When the gateway is in removing mode (please

refer to the instruction of the Z-Wave gateway for the operations on gateway itself),

press the program button 3 times within 1.5s (the interval between each press is

less than 0.5s).

5. Remote control: After the device is included in a Z-Wave gateway, the gateway can

provide control of an individual device, groups of devices and scenes, and offers

flexibility in setting up the lighting control network. Please refer to the gateway

instructions for details.

Wireless Range Conditions

The wireless range is the effective distance of remote control and it will be

impacted by the following conditions:

• Each wall or obstacle (e.g., refrigerator, TV, etc.) between the remote or Z-

Wave device and the destination device will reduce the wireless range.

• Brick, tile, or concrete walls block more of the wireless signal than walls made

of wooden studs and plasterboard (drywall).

• The angle of direction between the remote or Z-Wave device and the

destination device will also impact the wireless range; normally, placing the Z-

Wave device face-to-face will get the best wireless range.

• Wall-mounted Z-Wave device installed in metal junction boxes may suffer a

significant loss of range since the metal box blocks a large part of the wireless

signal.

Instruction Bulletin SQR62101WHZ Z-Wave Plug-in

6. Reset to factory defaults:

Press the program button 3 times then press and hold it for more than 10s.

NOTE:

• Use this procedure only when the Z-Wave gateway is missing or otherwise

inoperable.

• Reset the device to factory default settings will set the device to not in Z-Wave

network state, delete the association setting and restore the configuration

setting to the default.

• When the program button is pressed and held, the LED indicator will blink

quickly for 10 seconds and then the program button can be released after the

LED change to solid on, the LED will blink quickly for 3 seconds when factory

reset succeeds.

Advanced Setting The advanced setting requires an advanced gateway. Basic gateway does not

support this setting. Users can do the setting through the interface of the advanced

gateway.

All configuration parameters can be restored to factory default settings by the

gateway or by manual reset.

Configuration

Parameter No.

Size

Description

Valid Value

Default Value

1 byte

Synchronization of load

power and LED indicator

0 = Power ON, LED OFF

Power OFF, LED ON

Default = 1

1 = Power ON, LED ON

Power OFF, LED OFF

Association

Grouping ID

Max. No. of Nodes

Description

Lifeline: Send device reset locally notification

MultiLevelReport: Dimming percentage report

MeterReport: Power metering report

AssGroupSet: send on/off set command

LED Indication

Blue LED flashing

LED blinking slowly for 3 minutes: device not in network

LED blinking fast: adding/leaving network

LED stays on for 1 minute: adding/leaving network successfully

LED blinking fast for 3s: factory reset success

Blue LED on

Switch is turned on (default setting, can be configured)

SQR62101WHZ Z-Wave Plug-in Instruction Bulletin

Blue LED off

Switch is turned off (default setting, can be configured)

Trouble shooting

Issue

Possible Cause/Solution

SmartStart inclusion taking too long

Power cycle the switch to escalate the inclusion.

Inclusion is unsuccessful

Move the switch closer to the gateway and repeat the inclusion

operation.

FCC Statement

Federal Communication Commission Interference Statement

The equipment has been tested and found to comply with the limits for a class B Digital Device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment uses, generates and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction, may cause harmful interference to radio communication. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance

20cm between the radiator & your body.

RF Exposure: A distance of 20 cm shall be maintained between the antenna and users, and the transmitter module may not be co-located with any other transmitter or antenna.

Non-modification Statement:

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. FCC

Supplier’s Declaration of Conformity

Product Name: Z-Wave Plug-in

Model Number: SQR62101WHZ

Suppliers Name: Schneider Electric

Suppliers Address (USA) : 800 Federal Street Andover, MA 01810 USA

Suppliers Website: www.schneider-electric.us

FCC Compliance Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired operation.

ISED Statement

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s

licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.

2. This device must accept any interference, including interference that may cause undesired operation of the device.

L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement

économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :

L’appareil ne doit pas produire de brouillage;

L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.

This equipment complies with ISED RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be

installed and operated with a minimum distance of 20cm between the radiator and any part of your body.

Pour se conformer aux exigences de conformité CNR 102 RF exposition, une distance de séparation d'au moins 20 cm doit être maintenue entre

l'antenne de cet appareil ettoutes les personnes.

Model Number: SQR62101WHZ

Instruction Bulletin SQR62101WHZ Z-Wave Plug-in

Warranty Information

Schneider Electric warranties its products to be free of defects in materials and workmanship for a period of two (2) years. There are no

obligations or liabilities on the part of Schneider Electric for consequential damages arising out of or in connection with the use or performance of

this product or other indirect damages with respect to loss of property, revenue, or profit, or cost of removal, installation, or reinstallation.

Schneider Electric USA, Inc.

800 Federal Street

Andover, MA 01810 USA

888-778-2733

www.se.com/us

Electrical equipment should be installed, operated, serviced, and maintained only by

qualified personnel. No responsibility is assumed by Schneider Electric for any

consequences arising out of the use of this material.

Schneider Electric and Square D are trademarks and the property of

Schneider Electric SE, its subsidiaries, and affiliated companies. All other trademarks

are the property of their respective owners.

Square D SQR62101WHZ Manuel utilisateur

Marque: Square D

Modèle: SQR62101WHZ

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Square D SQR62101WHZ User manual

Square D SQR62101WHZ Manuel utilisateur

Square D SQR62101WHZ Manuel utilisateur

dans d''autres langues

Autres documents