Savant QP2APD10 Manuel utilisateur

Marque: Savant

Modèle: QP2APD10

Taper: Manuel utilisateur

Savant Product Regulatory Statement | 009-1950-02

45 Perseverance Way, Hyannis, MA 02601

Savant.com | 508.683.2500

1 of 2

Important Safety Information - Read First!

Before installing, conﬁguring, or operating any equipment, all relevant technical documentation must be read,

understood, and followed. Savant technical documentation may contain important product-speciﬁc installation,

mounting, and safety instructions, and can be accessed through the Savant Store.

Scan the QR code or visit the URL below, enter the relevant product name or SKU in the Search Savant prompt, and

select the product purchased to ﬁnd documents, speciﬁcations and more.

https://store.savant.com/DefaultStore/ccrz__HomePage

Product Information and Regulatory Statement

Safety Statements

All safety instructions below must be read, understood, and

carefully followed under all applicable circumstances when

working with any Savant equipment.

1. Follow all input power ratings marked on product near power

input!

2. If fuse replacement is required, replacement fuse should match

fuse rating marked on the product.

3. Do not use equipment near water.

4. Clean only with dry cloth.

5. Do not block any ventilation openings or install near any heat

sources such as heat registers, stoves, radiators, ampliﬁers,

etc.

6. Refer all servicing to qualiﬁed service personnel. Servicing is

required when any part of the apparatus has been damaged in

any way, or fails to operate normally for any reason.

7. Use only attachments/accessories speciﬁed by the

manufacturer, following all relevant safety precautions for any

such attachments/accessories.

8. For applicable equipment, use the included power cord with

the grounding prong intact to insure proper grounding of the

device.

9. If the provided plug does not ﬁt the desired outlet, contact a

licensed electrician to replace the obsolete outlet.

10. Protect any power cord from being walked on, pinched,

strained, or otherwise potentially damaged, especially at the

outlet or device connections.

11. Disconnect any outlet powered apparatus from its power

source during lightning storms or when unused for long

periods of time.

12. To completely disconnect equipment from AC mains power,

disconnect the power supply cord plug from the AC

receptacle on the device.

13. For any hardwired or ﬁxed in-wall apparatus, carefully follow

all wiring diagrams and instructions. All electrical wiring

and servicing should be performed by a properly licensed

electrician.

Déclarations de Sécurité

Toutes les instructions de sécurité ci-dessous doivent être lues,

comprises et soigneusement suivies dans toutes les circonstances

applicables lorsque vous travaillez avec un équipement Savant.

1. Suivez toutes les puissances nominales indiquées sur le

produit près de la puissance absorbée!

2. Si le remplacement du fusible est nécessaire, le fusible de

remplacement doit correspondre à la valeur nominale du

fusible indiquée sur le produit.

3. N’utilisez pas d’équipement près de l’eau.

4. Nettoyer uniquement avec un chion sec.

5. Ne bloquez pas les ouvertures de ventilation et n’installez pas

à proximité de sources de chaleur telles que les registres de

chaleur, les cuisinières, les radiateurs, les ampliﬁcateurs, etc.

6. Conﬁez toutes les réparations à un technicien qualiﬁé.

Un entretien est requis lorsqu’une partie de l’appareil a

été endommagée de quelque manière que ce soit ou ne

fonctionne pas normalement pour une raison quelconque.

7. Utilisez uniquement les attachements / accessoires spéciﬁés

par le fabricant, en suivant toutes les précautions de sécurité

applicables à ces attachements / accessoires.

8. Pour l’équipement applicable, utilisez le cordon d’alimentation

inclus avec la broche de mise à la terre intacte pour assurer

une mise à la terre correcte de l’appareil.

9. Si la ﬁche fournie ne correspond pas à la prise souhaitée,

contactez un électricien agréé pour remplacer la prise

obsolète.

10. Protégez tout cordon d’alimentation contre les piétinements,

les pincements, les tensions ou autres dommages potentiels,

en particulier au niveau de la prise ou des connexions de

l’appareil.

11. Débranchez tout appareil alimenté par une prise de courant de

sa source d’alimentation pendant les orages ou lorsqu’il n’est

pas utilisé pendant de longues périodes.

12. Pour déconnecter complètement l’équipement du secteur,

débranchez la ﬁche du cordon d’alimentation de la prise

secteur de l’appareil.

13. Pour tout appareil encastré ou câblé, suivez attentivement

tous les schémas de câblage et les instructions. Tout le

câblage électrique et l’entretien doivent être eectués par un

électricien dûment agréé.

IMPORTANT NOTES:

• For product mounting, installation, safety instructions, technical speciﬁcations, and more, refer to the product Quick

Reference Guide, available via the link or QR code noted above.

• For regulatory and compliance information, see reverse of this sheet and/or product packaging.

Savant Product Regulatory Statement | 009-1950-02

45 Perseverance Way, Hyannis, MA 02601

Savant.com | 508.683.2500

2 of 2

FCC Regulations

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for CLASS B digital devices, pursuant to Part 15 of FCC Rules.

These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential

installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications. If this equipment does cause harmful interference to radio

or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try correcting the

interference with one or more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and the receiver.

– Connect this equipment to an outlet on a circuit dierent from that to which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

FCC Caution

Any changes or modiﬁcations not expressly approved by the party responsible for compliance could void the user’s authority to

operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Radiation Exposure Statement - Wireless and Handheld Devices Only

This equipment complies with FCC and IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be

installed and operated with minimum distance of 20 cm between the radiator and your body.

FCC and IC Identiﬁer - Devices with Integrated Screen or User Interface Only

This device electronically displays the FCC declaration of conformity logo as well as the FCC and IC identiﬁer. This information can be

found on the device by accessing:

(Service menu) > About (A propos de)

IC Statement

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

1. This device may not cause interference, and

2. This device must accept any interference, including interference that may cause undesired operation of the device.

This Class B digital apparatus complies with Canadian ICES-003/NMB-003.

This device complies with RSS-247 of Industry Canada. Operation is subject to the condition that this device does not cause harmful

interference.

This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter, except tested

built-in radios. The Country Code Selection feature is disabled for products marketed in the US/Canada.

Déclaration IC

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est

autorisée aux deux conditions suivantes:

1. L’appareil ne doit pas produire de brouillage, et

2. Cet appareil accepter toute interférence, y compris les interférences pouvant provoquer fonctionnement indésirable d’appareil.

Déclaration d’exposition aux radiations

Cet équipement est conforme aux limites d’exposition aux radiations de la FCC déﬁnies pour un environnement non contrôlé. Cet

équipement doit être installé et utilisé avec une distance minimale de 20 cm entre le radiateur et votre corps.

Identiﬁcateur de la FCC et d’Lc

Ce périphérique par voie électronique ache le logo de déclaration de conformité FCC ainsi que l’identiﬁcateur de la FCC et d’IC. Cette

information peut être trouvée sur le terminal en accédant à:

(Menu de service) > About (A propos de)

Dual 500W Adaptive Phase Dimmer Installation Manual | 009-2117-00 4 of 4 45 Perseverance Way, Hyannis MA 02601

NOTES

Circuit Test Instructions

The instructions below can be used to test that the dimmer modules are functioning correctly. The setup requires the following:

–Adaptive Phase Companion Dimmer Module.

–Resistive loads with maximum amperage of 4.16 Amps.

–15 amp circuit breaker.

–Breaker test panel. The type of dimmer module determines the type of breaker panel (plug-on neutral or not).

–120V AC source

1. Plug a feeder circuit breaker and an Adaptive Phase Dimmer Companion Module into the circuit breaker test panel. The feeder breaker should

not exceed 15A.

2. Connect the output of the feeder circuit breaker to the INPUT

screw port on the dimmer module.

3. Connect a supported type load to Output A on the dimmer module.

4. Connect a second supported type load to Output B on the dimmer

module.

5. Connect the unused side of each load to the neutral bus bar in the

breaker panel.

6. On modules that contain a neutral pigtail wire, connect the neutral

wire to the neutral bus bar.

7. Apply power to the breaker panel (not shown in diagram).

8. Toggle the feeder circuit breaker On.

9. To test, toggle the CIRCUIT POWER switches A and B to ON and

verify both loads switch On.

10. Toggle the CIRCUIT POWER switches to AUTO and verify the loads

switch O .

CIRCUIT BREAKER

OUTPUT OUTPUT

INPUT

CIRCUIT POWER

AUTO

PAIR

ADAPTIVE PHASE

DIMMER

Neutral Bus Bar

Neutral pigtail wire from

the companion module

Load B

4.16A (max)

Load A

4.16A (max)

910

IMPORTANT!

–When making connections, observe all general electrical best practices including wire sizing guidelines.

–The GPM-QP2APD10-21 and GPM-Q2APD10-21 modules can accept up to a #14 AWG wire. See the Branch Circuit Minimum Size of

Conductors table on page 2 for wire sizing information.

Dual 500W Adaptive Phase Dimmer Installation Manual | 009-2117-00 1 of 4 45 Perseverance Way, Hyannis MA 02601

PAIR

DO NOT

PRESS ON

SCREEN

REMOVE AFTER

INSTALLATION

ADAPTIVE PHASE DIMMER

GPM-QPAPD10-21

INPUT

INDOOR USE ONLY

#10-8 AWG Cu ONLY

HOME AUTOMATION EQUIP

IC ID: 10798A-QPAPD10

FCC ID: PUU-QPAPD10

EXXXXXX YYWW

120VAC 60Hz

120VAC 500W MAX PER CHANNEL

OUTPUT

INPUT

OUTPUT

CIRCUIT POWER

Multi-Page LCD screen can display the following:

–Energy usage in watts at the output.

–Percentage of brightness at the output.

–Firmware, Mac Address, and FCC/IC Info.

–Real time Bluetooth status connectivity icon.

BManual Load Switches - Toggle to the ON position to switch

the load on. Toggle switch to AUTO for normal operation.

Switch A controls output A, Switch B controls output B.

PAIR Button - The PAIR button is a multi-use button. The

duration that the button is pressed and held determines the

function that gets initiated:

Press and Release - Cycles through the screens available on

the LCD (POWER > DIMMER > INFO 1 > INFO 2).

Press and hold - Press and hold for 2 seconds to put module

into pairing mode. Press and hold for 5 seconds to reset.

DInput Power Connection - Connect the 120V AC output from

a feeder breaker to this input.

EOutput Connections - The connections are labeled OUTPUT

A and OUTPUT B. Connect each output to a separate load.

See the Wiring section below.

F120V AC Connection - Plugs into the 120V AC bus bar in the

breaker panel. The voltage on this connection powers the

module.

Neutral - The model number of the module determines the

type of neutral connection:

– Plug-On Neutral - Positioned on the bottom of the

module is a neutral clip that plugs directly onto the

neutral bar.

– Pigtail Neutral - A neutral wire protrudes from the

module’s rear and gets wired to the neutral bar in the

breaker panel.

Minimum Supported Release

Savant OS da Vinci 10.2

Electrical and Safety Characteristics

Screw Tighten Torque 3.0 Nm

Wire / Conductor Type Copper (Cu) only

Pollution Degree 2

Purpose of Control Operating Control, Smart Relay Control

Module or the equivalent

Software Class A

Impulse Voltage 2500V

Supported Load Types

Standard

Conﬁ guration

Dimmable circuits – LEDs, incandescent,

halogen, electronic low-voltage (solid

state) transformers, magnetic low-voltage

transformers, ﬂ uorescents, and dimmable

compact ﬂ uorescents.

Minimum Power > 6W

Standards

Wireless Bluetooth Low Energy (BLE)

–2.4 GHz radio frequency

Regulatory

Safety and

Emissions

FCC Part 15 UL ICES 003

Contains FCC ID: PUU-QP2APD10

Contains IC: 10798A-QP2APD10

RoHS Compliant

Power

Input Power

(powers the module) 120V AC (+/-10%) @ 60 Hz, 0.1A (max)

Input Power

(from external source) 120 AC per input - 15A (max)

Load Power 500VA

(4.16A @ 120V AC per channel max)

Features of

Automatic Action Type 1 Action

Dimensions and Weights

Height Width Depth Weight

Module

(QO)

1.48 in.

(3.76 cm)

5.00 in.

(12.70 cm)

2.63 in.

(6.68) cm

.5 lbs

(.23 kg)

Shipping 1.71 in.

(4.34 cm)

7.50 in.

(19.05 cm)

4.30 in.

(10.92 cm)

1.0 lbs

(.45 kg)

Environmental

Temperature 32° to 104° F (0° to 40° C)

Humidity 5% to 85% Relative Hum. (non-condensing)

Location Indoor Use Only

–Each output can control dimming loads up to 500 VA (volt-

ampere). See the Branch Circuit Minimum Size of Conductors table

on page 2.

–All QO™ style dimmer modules are compatible with Schneider

Electrics’ Square D™ QO™ load centers.

–Both forward and reverse phase dimming is supported.

–Built-in energy monitoring; +/- 3% accuracy / 1 sec sample time.

–Communicates over the air using Bluetooth Low Energy (BLE)

technology.

–Color LCD display for easy identiﬁ cation and load status.

Features

Dual 500W Adaptive Phase Companion Module Dimmer

Quick Reference and Installation Guide

Speciﬁ cations

Box Contents Descriptions

(1) Adaptive Phase Dimmer Companion Module

–GPM-QP2APD10-21 QO™ Plug-on Neutral -or-

–GPM-Q2APD10-21 QO™ Pigtail

(1) Product Information and Regulatory Insert (009-1950)

(1) Quick Reference Guide (this document)

Construction of Control

Open Type Independently mounted for ﬂ ush mounting

Recommended Load Center Types

All QO™ compatible modules ﬁ t into ¾ inch load centers.

Dual 500W Adaptive Phase Dimmer Installation Manual | 009-2117-00 2 of 4 45 Perseverance Way, Hyannis MA 02601

1. Remove power from the breaker panel by switching o the panel’s main breaker.

2. Position and install a circuit breaker into one of the slots in the panel. Press ﬁ rmly until the breaker is fully seated onto the appropriate bus

bars.

3. Position and install the Savant dimmer module into the slot where it will be installed. Press ﬁ rmly until fully seated onto the appropriate bus

bars. Typically, the Companion Module(s) are installed alongside the circuit breaker but doesn’t need to be.

4. Use the wiring diagrams on the next page to complete the wiring.

Installation into Breaker Panel

Important Information

–To determine the feeder breaker’s size, do the following:

1. Determine the wattage requirements of each load connected to the dimmer module.

2. Sum up the wattage of all the loads.

3. Divide the total wattage by the input voltage. This is the total current drawn.

–To determine the number of breaker panel spaces needed, add the number of spaces required for each circuit breaker to the number of

spaces needed for the dimmer module.

• Each circuit breaker requires one space.

• Each dimmer module requires two spaces.

–The total current drawn from the loads should not exceed 80% of the size of the breaker for that circuit. For example, with a 15 amp breaker,

12 amps or 1440 watts. With a 20 amp breaker, max would be 16 amps or 1920 watts.

–Do not add MLV and ELV type loads to the same breaker/dimmer module circuit. MLV and ELV type loads should be connected to separate

breakers. Doing this could cause damage to the dimming module.

ELECTRIC SHOCK! The 120V AC, 60 Hz source poses an

electrical shock hazard that has the potential to cause serious

injury to installers and end users.

CAUTION! Risk of Electric Shock - More than one disconnect

switch may be required to de-energize the device before

servicing.

IMPORTANT! A licensed electrician is required to install Savant’s

Companion Modules.

Branch Circuit Minimum Size of Conductors

(General circuit wiring, Copper Conductors)

15A 20A 30A 40A 50A 60A

#14 AWG #12 AWG #10 AWG #8 AWG #6 AWG #4 AWG

NOTE: This wiring requirement was based on the National Electric Code

(NEC) (ANSI/NFPA70), Canadian Electric Code, Part 1 (CEC), and local

codes Minimum Size of Conductors.

Output Power Maximums

The table below shows the maximum wattage that each type of dimmer module can handle. Use the table to determine the number of loads that

can safely be wired to each module’s output.

Dimmer Type Incandescent MLV LED

Forward Phase 300W 240W Not Recommended

Reverse Phase 500W 400W 150W

Dual 500W Adaptive Phase Dimmer Installation Manual | 009-2117-00 3 of 4 45 Perseverance Way, Hyannis MA 02601

Wiring

Plug-on Neutral Bus Bar with ARC Fault Breakers Plug-on Neutral Bus Bar with Standard Breakers

Use the appropriate diagram below when wiring the dimming module, breaker, and load(s).

Neutral Bar

To neutral on

AFCI breaker

Phase A Phase B

Breaker Panel

Gnd

Bar

plug-on

neutral bar

120VAC

Use AFCI / GFCI protection where

required by local regulations

OUTPUT OUTPUT

INPUT

CIRCUIT POWER

AUTO

PAIR

ADAP PHASE DIMMER

GPM-Q2APD10

ARC FAULT

BREAKER

Load ALoad B

Neutral Bar

Phase A Phase B

Breaker Panel

Gnd

Bar

Use AFCI / GFCI protection where

required by local regulations

OUTPUT OUTPUT

INPUT

CIRCUIT POWER

AUTO

PAIR

ADAP PHASE DIMMER

GPM-Q2PAPD10

BREAKER

Load B Load A

120VAC

plug-on

neutral bar

Standard Neutral Bus Bar with ARC Fault Breakers Standard Neutral Bus Bar with Standard Breakers

Neutral Bar

Connect the pigtail

wire to the neutral bar.

Neutral from

AFCI breaker.

Phase A Phase B

Breaker Panel

Gnd

Bar

120VAC

Use AFCI / GFCI protection where

required by local regulations

OUTPUT OUTPUT

INPUT

CIRCUIT POWER

AUTO

PAIR

ADAP PHASE DIMMER

GPM-Q2APD10

ARC FAULT

BREAKER

Load B Load A

Neutral Bar

Phase A Phase B

Breaker Panel

Gnd

Bar

Use AFCI / GFCI protection where

required by local regulations

OUTPUT OUTPUT

INPUT

CIRCUIT POWER

AUTO

PAIR

ADAP PHASE DIMMER

GPM-Q2APD10

BREAKER

Load ALoad B

120VAC

Additional Documentation

Further information is available in the documents listed below and can be accessed via the Savant Customer Community.

–Panel Bridge Controller with PoE (PBC-P1000) QRG

–Savant Panelized Lighting Deployment Guide.

Savant QP2APD10 Manuel utilisateur

Marque: Savant

Modèle: QP2APD10

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Savant QP2APD10 User manual

Documents connexes

Autres documents

deako Smart Plug Include Floor Lamps and String Lights Manuel utilisateur