Savant HST-STUDIO55WS-SUR-00 Guide de référence

Marque: Savant

Modèle: HST-STUDIO55WS-SUR-00

Catégorie: Haut-parleurs de la barre de son

Taper: Guide de référence

HST-STUDIO55WS-SUR Quick Reference Guide | 009-1878-04 45 Perseverance Way, Hyannis, MA 02601

Box Contents

(1) Smart Series WiSA Soundbar (HST-STUDIO55WS-SUR)

(1) Soundbar (093-3183-xx)

(1) Standard Grille (093-3181-xx)

(1) Power Cord (064-0480-xx)

(2) 6-Pin Control Connector (028-9352-xx)

(1) Install Kit (075-0241-xx)

(2) Wall Mounting Bracket (071-1130-xx)

(1) 3mm Allen Wrench (015-0222-xx)

(8) M5x10mm hex screw (039-0440-xx)

(4) 25mm Washer 5mm ID (039-0437-xx)

(2) Bracket Extension 50x90 (071-1112-xx)

(2) Bracket Extension 70x90 (071-1113-xx)

(2) Rubber Feet (073-0007-xx)

(3) IR Emitter (064-0020-xx)

(1) IR Learner (064-0511-xx)

(1) Product Regulatory Insert (009-1950-xx)

Optional Accessories (sold separately)

– Smart Audio Soundbar TV Mount Hardware

(MNT-STUDIO55WS-TV-xx)

– Custom Grilles matched to Flat Panel TV’s

Savant® Smart Series WiSA Soundbar [HST-STUDIO55WS-SUR-xx]

Quick Reference Guide

Front Panel

Front Tweeters (3) 25 mm Vifa XT Super Audio Tweeters

Midrange/

Woofers

(6) 89 mm Long Throw Carbon Fiber

Midrange/Woofers

Side and Bottom Panel

Stage Tweeters (2) 19mm Silk Tweeters

Mounting Slide (2) Captive M5 threaded bracket

WiSA

Speciﬁcations

Environmental

Temperature 32° to 104° F (0° to 40°C)

Humidity 10% to 90% (non-condensing)

Dimensions and Weights

Height Width Depth Weight

Soundbar

4.17 in

(10.59 cm)

53.41 in

(135.65 cm)

2.25 in

(5.71 cm)

21.7 lb

(9.9 kg)

with included

Grille

4.61 in

(11.71 cm)

53.41 in

(135.65 cm)

2.40 in

(5.93 cm)

27.9 lb

(12.7 kg)

Shipping

9.50 in

(24.13 cm)

63.20 in

(160.53 cm)

6.50 in

(16.51 cm)

33.0 lb

(15.0 kg)

Power

Input 120/240V AC (50/60 Hz)

Maximum 250W

Operating Parameters

Frequency

Response

80 Hz - 40 kHz +/- 3 dB

Sensitivity 89 dB @ 2.83V/1 meter

Networking

Wired IEEE 802.1 AVB/TSN 2

Wireless IEEE 802.11 b/g/n 2.4GHz/5.0GHz

Regulatory

Safety and

Emissions

FCC Part 15 CE C-Tick

Contains FCC ID Z64-WL18DBMOD

Contains IC 451I-WL18DBMOD

RoHS Compliant

Minimum Supported Release

Savant Software

da Vinci 9.2

Studio 3.1

HST-STUDIO55WS-SUR Quick Reference Guide | 009-1878-04 45 Perseverance Way, Hyannis, MA 02601

Rear Panel

100-240 V~ 50-60 HZ 2.2A

Smart Audio Soundbar

Ethernet

ResetStatus

Digital Audio

RS232

GND

Learner

Sub

Out

A B

C D

E F G H I

Status LED

O: Embedded processor is resetting, or is powered up, and is booting the embedded ﬁrmware.

Green: Host has established communications with the embedded system.

Green Blinking: Embedded system is ready, but no communication has been established with the host.

Red: Host has determined the ﬁrmware needs to be updated, but a problem occurred during the process that will

initiate a reset.

Red Blinking: Embedded ﬁrmware is running, but has not received a DHCP IP Address.

Amber: Host is updating the embedded ﬁrmware.

Amber Blinking: Embedded system has a valid link local IP Address and is connecting to the host.

Hardware Failure: If a hardware failure occurs, the status LED indication will be interrupted every three seconds with

a solid red indication. For example, if the LED is blinking green when a hardware failure occurs, the LED will alternate

between blinking green and solid red at three-second intervals.

Digital Audio

Input

Digital optical audio inputs (TOSLink).

Inputs support up to 192kHz/24-bit digital audio and up to 5.1 encoded audio.

Ethernet

8-pin RJ-45 port 10/100 Base-T auto-negotiating port.

Supports Audio Video Bridging (AVB).

Serial Ports

(2) RS-232 Ports

Uses 6-pin Screw down plug-in connection. Transmits and receives serial data to and from serial controllable devices.

Reset

Resets the network.

Hold Reset Button for 5 seconds while powered on to clear network settings. Status LED will rapidly blink red when

reset is complete.

IR Learner 3.5 mm connection, for use with the included IR learner (Studio Only).

Sub Out 3.5 mm analog connection, Direct line level, 2.1 V

RMS

max.

IR Ports

(3) IR Ports

Uses 6-pin IR Connectors to send IR signals to control devices with an IR input or IR receiver via an IR ﬂasher (5V

tolerant only).

Power Input 120/240V AC (50/60 Hz)

Installation

Wall Mount

1. Attach the Wall Mounting Brackets to the wall using the appropriate

fasteners to account for the weight of the soundbar.

NOTE: The two wall brackets must be far enough apart so the

soundbar does not wobble on the wall.

2. Make the power and control connections before the soundbar is

attached to the brackets.

3. Attach the Soundbar.

Rubber Feet

IMPORTANT! The rubber feet must be used with the included

grille.

1. Align the foot under the center speaker of the Right/Left Channel.

2. Remove the waxed paper from the adhesive.

3. Attach the foot to the soundbar.

4. Repeat for the second rubber foot.

Host Mode

Host mode can be disabled/enabled from the device’s Web UI. For

more information see the IP Audio Products with Integrated Host

Deployment Guide (009-1839-xx).

Further Product Information

To view available documentation, detailed product specs, and more:

– Visit the Savant Knowledge tab via the Savant Customer

Community to search all Savant documentation.

HST-STUDIO55WS-SUR Quick Reference Guide | 009-1878-04 45 Perseverance Way, Hyannis, MA 02601

FCC Regulations

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the requirements for CLASS B digital devices, pursuant to Part 15 of FCC Rules.

These requirements are designed to provide reasonable protection against harmful interference when the equipment is operated in a

residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance

with the instructions, may cause harmful interference to radio communications. If this equipment does cause harmful interference to radio

or television reception (which can be conﬁrmed by turning the equipment o and on), the user is encouraged to attempt to correct the

interference using one or more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and the receiver.

– Ensure that the power sources for this equipment and the receiver are connected to dierent circuits.

– Consult the dealer or an experienced radio/TV technician for help.

FCC Caution

Any changes or modiﬁcations not expressly approved by the party responsible for compliance could void the user's authority to operate this

equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Déclaration d'exposition aux radiations

Cet équipement est conforme aux limites d'exposition aux radiations de la FCC déﬁnies pour un environnement non contrôlé. Cet équipe-

ment doit être installé et utilisé avec une distance minimale de 20 cm entre le radiateur et votre corps.

IC Statement

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

1. This device may not cause interference, and

2. This device must accept any interference, including interference that may cause undesired operation of the device.

– This Class B digital apparatus complies with Canadian ICES-003.

– This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter, except tested

built-in radios. The Country Code Selection feature is disabled for products marketed in the US/Canada.

Déclaration IC

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est au-

torisée aux deux conditions suivantes:

1. L'appareil ne doit pas produire de brouillage, et

2. Cet appareil accepter toute interférence, y compris les interférences pouvant provoquer un fonctionnement indésirable d’appareil.

– Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

– Cet appareil et son antenne ne doivent pas être situés ou fonctionner en conjonction avec une autre antenne ou un autre émetteur,

exception faites des radios intégrées qui ont été testées. La fonction de sélection de l'indicatif du pays est désactivée pour les produits

commercialisés aux États-Unis et au Canada.

Radiation Exposure Statement

This device meets the government’s requirements for exposure to radio waves.

This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal

Communications Commission of the U.S. Government.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed

and operated with a minimum distance of 20cm between the radiator & your body.

The exposure standard for wireless device employs a unit of measurement known as the Speciﬁc Absorption Rate, or SAR. The SAR limit set

by the FCC is 1.6W/kg. *Tests for SAR are conducted using standard operating positions accepted by the FCC with the device transmitting at

its highest certiﬁed power level in all tested frequency bands.

HST-STUDIO55WS-SUR Quick Reference Guide | 009-1878-04 45 Perseverance Way, Hyannis, MA 02601

Important Safety Information - Read First

Before installing, conﬁguring, or operating any equipment, Savant

recommends that each dealer, integrator, installer, etc. access and read

all relevant technical documentation. Savant technical documenta-

tion can be located by visiting Savant.com. Vendor documentation is

supplied with the equipment.

Read and understand all safety instructions, cautions, and warnings in

this document and the labels on the equipment.

Safety Statements

All safety instructions below should be read, understood, and applied

under all relevant circumstances when working with this equipment.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with

the manufacturer's instructions.

8. Do not install near any heat sources such as radiators, heat regis-

ters, stoves, or other apparatus (including ampliﬁers) that produce

heat.

9. Do not defeat the safety purpose of any polarized or ground-

ing-type plug. A polarized plug has two blades with one wider

than the other. A grounding type plug has two blades and a third

grounding prong. The wide blade or the third prong is provided

for your safety. If any provided plug does not ﬁt into your outlet,

consult an electrician for replacement of the obsolete outlet.

10. Protect any power cord from being walked on or pinched; partic-

ularly at plugs, convenience receptacles, and the point where they

exit from the apparatus.

11. Use only attachments/accessories speciﬁed by the manufacturer,

following all relevant safety precautions for any such attachments/

accessories.

12. Disconnect any outlet powered apparatus from its power source

during lightning storms or when unused for long periods of time.

13. Refer all servicing to qualiﬁed service personnel. Servicing is

required when the apparatus has been damaged in any way, such

as a damaged power supply cord or plug, liquid being spilled or ob-

jects having fallen into the apparatus, the apparatus being exposed

to rain or moisture, apparatus having been dropped, or other failure

to operate normally.

14. To completely disconnect equipment from AC mains power,

disconnect the power supply cord plug from the AC receptacle.

15. For applicable equipment, use the included power cord with the

grounding prong intact to insure proper grounding of the device.

16. For any hardwired or ﬁxed in-wall apparatus, carefully follow all

wiring diagrams and instructions. All electrical wiring and servicing

should be performed by a properly licensed electrician.

Informations importantes sur la sécurité - Lire

d’abord

Avant d’installer, de conﬁgurer et d’utiliser des équipements Savant

et d’autres équipements fournisseurs, Savant recommande à chaque

revendeur, intégrateur, installateur, etc. d’accéder et de lire toute la

documentation technique requise. La documentation technique de

Savant peut être localisée en visitant Savant.com. La documentation

du fournisseur est fournie avec l’équipement.

Lisez et comprenez toutes les consignes de sécurité, les mises en

garde et les avertissements dans ce document et les étiquettes sur

l’équipement.

Déclarations de sécurité

Suivez toutes les consignes de sécurité ci-dessous et appliquez le cas

échéant. Des informations de sécurité supplémentaires seront incluses,

le cas échéant.

1. Lisez ces instructions.

2. Gardez ces instructions.

3. Suivez tous les avertissements.

4. Suivez toutes les instructions.

5. Ne pas utiliser cet appareil près de l’eau.

6. Nettoyer uniquement avec un chion sec.

7. Ne bloquez aucune bouche d’aération. Installez conformément aux

instructions du fabricant.

8. Ne pas installer à proximité de sources de chaleur telles que des ra-

diateurs, des registres de chaleur, des poêles ou d’autres appareils

(y compris les ampliﬁcateurs) qui produisent de la chaleur.

9. Ne pas vaincre l’objectif de sécurité de la ﬁche polarisée ou de mise

à la terre. Une ﬁche polarisée a deux lames avec une lame plus

large que l’autre. Une ﬁche de type à terre possède deux lames

et une troisième broche de mise à la terre. La lame large ou la

troisième broche est fournie pour votre sécurité. Si la ﬁche fournie

ne rentre pas dans votre prise, consultez un électricien pour le rem-

placement de la prise obsolète.

10. Protégez le cordon d’alimentation d’être piétiné ou pincé en partic-

ulier sur les bouchons, les récipients de commodité, et le point où

ils sortent de l’appareil.

11. N’utilisez que des pièces jointes ou accessoires spéciﬁées par le

fabricant, en suivant toutes les précautions de sécurité appropriées

pour tout accessoire ou accessoires.

12. Débranchez tout équipement de la source d’alimentation pendant

les orages ou quand il est inutilisé pendant de longues périodes de

temps.

13. Conﬁez toute réparation à un personnel qualiﬁé. Un entretien est

nécessaire lorsque l’appareil a été endommagé de quelque manière

que ce soit, tel qu’un cordon d’alimentation ou une ﬁche endom-

magé, un liquide renversé ou des objets tombés dans l’appareil,

exposé à la pluie ou à l’humidité, ne fonctionnant pas normalement,

ou a été chuté.

14. Pour déconnecter complètement cet équipement du secteur,

débranchez la ﬁche du cordon d’alimentation de la prise secteur.

15. Pour les équipements applicables, utilisez le cordon d’alimentation

fourni avec la broche de mise à la terre intacte pour assurer la mise

à la terre correcte de l’appareil.

16. Pour tout appareil câblé ou ﬁxe dans le mur, suivez attentivement

tous les schémas de câblage et les instructions. Tout le câblage

électrique et l’entretien doivent être eectués par un électricien

dûment agréé.

Savant HST-STUDIO55WS-SUR-00 Guide de référence

Marque: Savant

Modèle: HST-STUDIO55WS-SUR-00

Catégorie: Haut-parleurs de la barre de son

Taper: Guide de référence

Télécharger le PDF

rapport

dans d''autres langues

English: Savant HST-STUDIO55WS-SUR-00 Reference guide

Documents connexes

Autres documents

Primare PRE35 DAC Mode d'emploi