May 2023
QSG1_A_EN
Argus PT Lite
Quick Start Guide
@ReolinkTech https://reolink.com
58.03.001.0325
English English1 2
What's in the Box
Camera
Quick Start Guide Surveillance Sign
Pack of Screws Mounting Template
Camera Bracket Type-C CableMount Base
Antenna Reset Needle
EN
Content
What’s in the Box ·············································································2
Camera Introduction ·········································································3
Set up the Camera ···········································································4
Charge the Camera ··········································································6
Install the Camera ············································································7
Safety Instructions of Battery Usage ·························································12
Troubleshooting ·············································································13
Specication ················································································14
Notication of Compliance ··································································14
Hex Key
English English3 4
OFF
ON
POWER
RST
MicroSD
OFF
ON
POWER
RST
MicroSD
OFF
ON
POWER
RST
MicroSD
Set up the CameraCamera Introduction
Set up the Camera Using a Smartphone
Step 1 Scan to download the Reolink App from the App Store or Google Play store.
Step 2 Turn on the power switch to power on the camera.
Dierent states of the status LED:
Red Light: WiFi connection failed Blinking: Standby status
Blue Light: WiFi connection succeeded On: Working status
OFF
ON
POWER
POWER
OFF
ON
POWER
Lens
Power Switch
6 IR LEDs
Antenna
Charging Port
Daylight Sensor
Battery Status LED
Built-in PIR Sensor
Built-in Mic
StatusLED
Speaker
Reset Hole
Micro SD Card Slot
* Press for more than ve seconds to
restore the device to default settings.
* Rotate the camera’s lens to nd the
reset hole and the SD card slot.
1
10
2
11
12
3
13
4
5
6
7
8
9
3
7
9
8
2
1
11
10
4 6
12
13
5
English English5 6
Charge the Camera
Step 3 Launch the Reolink App, click the “ ” button in the top right corner to add the camera.
Scan the QR code on the device and follow the onscreen instructions to nish initial setup.
Charge the battery with a power adapter.
(not included)
Charge the battery with the Reolink Solar Panel
(Not included if you only purchase the camera).
For better weatherproof performance, please
always cover the charging port with the rubber
plug after charging the battery.
Step 2 Launch the Reolink Client, click the “ ” button, input the UID code of the camera to add it
and follow the onscreen instructions to nish initial setup.
Step 1 Download and install the Reolink Client: Go to https://reolink.com > Support > App&Client.
Set up the Camera on PC (Optional)
Devices
Cloud
You haven't added any device. Please click
the"+"button in the top right corner to add
OFFON
POWER
OFFON
POWER
Orange LED: Charing Green LED: Fully charged
Charging Indicator:
It’s recommended to fully charge the battery before mounting the camera.
OFFON
POWER
English English7 8
Install the Camera
• The camera MUST be
installed upside down for better
waterproof performance and
better PIR motion sensor’s
eciency.
• Install the camera 2-3 meters
(7-10 ft) above the ground. This
height maximizes the detection
range of the PIR motion sensor.
• For better motion detection
performance, please install the
camera angularly.
Notes on Camera
Installation Position
Mount the Camera
Mounting Height:
2-3 Meters
PIR Detection Distance:
2-10 Meters
Drill holes in accordance with the
mounting hole template and screw the
camera bracket to the wall.
NOTE: Use the drywall anchors included in the package if needed.
Install the antenna to the camera.
12
NOTE: If a moving object approaches the
PIR sensor vertically, the camera may fail
to detect motion.
English English9 10
Mount the Camera to Ceiling
Install the mount base to the ceiling. Align the camera with the mount base and turn the camera unit
clockwise to lock it in position.
1 2
Align the white hole on the camera top with the white hollow screw on the bracket. Use a wrench
and a hex head screw provided to secure the camera into place. Then cover the rubber plug.
3
English English11 12
You are allowed to strap the camera to a tree with both the security mount and ceiling bracket.
Thread the provided strap to the plate and fasten it to a tree. Next, attach the camera to the
plate and you are good to go.
Install the Camera with Loop Strap Safety Instructions of Battery Usage
The camera is not designed for running 24/7 at full capacity or around-the-clock live streaming.
It’s designed to record motion events and to live view remotely only when you need it. Learn useful
tips on how to extend the battery life in this post:
https://support.reolink.com/hc/en-us/articles/360006991893
1. Do not remove a built-in battery from the camera.
2. Charge the battery with a standard and high-quality DC 5V battery charger or Reolink solar
panel. It’s not compatible with solar panels from any other brands.
3. Charge the battery only if in temperatures between 0°C and 45°C. The battery is intended for
use only in temperatures between -10°C and 55°C.
4. Keep the charging port dry, clean and free of any debris. Cover it with the rubber plug after the
battery is fully charged.
5. Do not charge, use or store the battery next to areas that may become hot. Examples include,
but are not limited to, on or near a space heater, cooking surface, cooking appliance, iron, radiator,
or replace.
6. Do not use the battery if its case appears damaged, swollen, or compromised. Examples include,
but are not limited to, leaking, odors, dents, corrosion, rust, cracks, swelling, melting, and scratches.
7. Always follow the local waste and recycling laws to dispose of used batteries.
English English13 14
Troubleshooting
If your camera is not powering on, please try
the following solutions:
• Make sure the power switch is turned on.
• Charge the battery with a DC 5V/2A power
adapter. When the green light is on,
the battery is fully charged
If these won’t work, contact Reolink Support.
If you cannot scan the QR code on your
phone, please try the following solutions:
• Remove the protective lm from the camera
lens.
• Wipe the camera lens with a dry paper/
towel/tissue.
• Vary the distance between your camera
and the mobile phone so that the camera can
focus better.
Camera is Not Powering On
Failed to Scan QR Code
on the Phone
Reolink declares that this device is in
compliance with the essential requirements
and other relevant provisions of Directive
2014/53/EU and Directive 2014/30/EU.
Operating Temperature:
-10°C to 55°C (14°F to 131°F)
Dimensions: 98 x 122mm
Weight: 472g
For more specications, visit the
Reolink ocial website.
CE Declaration of Conformity
Specication
Notication of
Compliance
Reolink declares that this product is in
compliance with Radio Equipment
Regulations 2017 and Electromagnetic
Compatibility Regulations 2016.
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following
two conditions: (1) this device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
Note: This equipment has been tested and
found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can
radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference
to radio communications. However, there is
no guarantee that interference will not occur
UKCA Declaration of Conformity
FCC Compliance Statements
• Try to scan the QR code under sucient
lighting.
If these won’t work, contact Reolink Support.
in a particular installation. If this equipment
does cause harmful interference to radio or
television reception, which can be determined
by turning the equipment o and on, the
user is encouraged to try to correct the
interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the
equipment and receiver.
• Connect the equipment into an outlet on a
circuit dierent from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/
TV technician for help.
Caution: Changes or modications not
expressly approved by the party responsible
for compliance could void the user’s authority
to operate the equipment.
English English15 16
This equipment complies with FCC radiation
exposure limits set forth for an uncontrolled
environment. This equipment should be
installed and operated with minimum distance
20cm between the radiator and your body.
This device contains licence-exempt
transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic
Development Canada’s licence-exempt
RSS(s). Operation is subject to the following
two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference,
including interference that may cause
undesired operation of the device.
L’ émetteur/récepteur exempt de licence
contenu dans le présent appareil est
conforme aux CNR d’Innovation, Sciences
et Développement économique Canada
applicables aux appareils radio exempts de
licence. L’ exploitation est autorisée aux deux
conditions suivantes :
(1) L’ appareil ne doit pas produire de
brouillage;
FCC Radiation Exposure statement
ISED Compliance Statements
This marking indicates that this product
should not be disposed with other household
wastes.throughout the EU. To prevent possible
harm to the environment or human health
from uncontrolled waste disposal, recycle it
responsibly to promote the sustainable reuse
of material resources. To return your used
device, please use the return and collection
systems or contact the retailer where the
product was purchased. They can take this
product for environmentally safe recycling.
Correct Disposal of This Product
Use of the product is subject to your
agreement to the Terms of Service and
Privacy Policy at reolink.com. Keep out of
reach of children.
Terms and Privacy
This product comes with a 2-year limited
warranty that is valid only if purchased from
Reolink Ocial Store or a Reolink authorized
reseller. Learn more:
https://reolink.com/warranty-and-return/.
Limited Warranty
Technical Support
If you need any technical help, please visit
our official support site and contact our
support team before returning the products,
https://support.reolink.com.
(2) L’ appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage
est susceptible d’en compromettre le
fonctionnement.
ISED Radiation Exposure statement
This equipment complies with IC RSS-102
radiation exposure limits set forth for an
uncontrolled environment. This equipment
should be installed and operated with
minimum distance 20 cm between the
radiator and your body.
Cet équipement est conforme aux limites
d’exposition aux radiations IC CNR-102 établies
pour un environnement non contrôlé. Cet
équipement doit être installé et utilisé avec
une distance minimale de 20 cm entre le
radiateur et votre corps. Cet émetteur ne doit
pas être colocalisé ou fonctionner en
conjonction avec
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
dans d''autres langues
- English: REOLINK 2305C User guide
Documents connexes
-
REOLINK Argus PT, PT Pro 4MP PIR Sensor Camera Mode d'emploi
-
REOLINK Argus Eco Mode d'emploi
-
-
REOLINK Argus PT (Out of Use) Manuel utilisateur
-
REOLINK Duo 2 LTE Manuel utilisateur
-
REOLINK Go PT Mode d'emploi
-
REOLINK Argus 3 Series Mode d'emploi
-
-
REOLINK Lumus Outdoor WiFi Security Camera Manuel utilisateur
-
REOLINK E1 Mode d'emploi