Pit Boss 3-Series Digital Electric Smoker Manuel utilisateur
- Catégorie
- Outils de jardin
- Taper
- Manuel utilisateur
ASSEMBLY AND OPERATION | ASSEMBLAGE ET FONCTIONNEMENT | MONTAJE Y OPERACIÓN
MODEL / MODÈLE / MODELO : PBV3D1
PART / PIÈCE / PARTE : 10947
'
DIGITAL ELECTRIC SMOKER (3-SERIES)
IMPORTANT, READ CAREFULLY, RETAIN FOR FUTURE
REFERENCE. MANUAL MUST BE READ BEFORE OPERATING!
FUMOIR ÉLECTRIQUE NUMÉRIQUE (SÉRIE 3)
IMPORTANT, PRENEZ CONNAISSANCE DE CE DOCUMENT
ET CONSERVEZ-LE POUR RÉFÉRENCE ULTÉRIEURE VOUS
DEVEZ LIRE CE GUIDE AVANT D’UTILISER LE BARBECUE !
AHUMADOR ELÉCTRICO DIGITAL (SERIE 3)
IMPORTANTE, LEA ATENTAMENTE, CONSERVE PARA
REFERENCIA FUTURA. ¡EL MANUAL DEBE LEERSE ANTES DE
OPERAR!
300522
CERTIFIED TO: UL1026 (6TH EDITION) / CSA-22.2 NO. 60335-2-78:14 & CSA-22.2 NO. 60335-1:11 ELECTRIC HOUSEHOLD COOKING AND FOOD SERVING APPLIANCE
CERTIFIÉ À : UL 1026 (6E ÉDITION) / CSA-22.2 NO. 60335-2-78:14 & CSA-22.2 NO. 60335-1:11 APPAREIL ÉLECTROMÉNAGER DE CUISSON ET DE SERVICE ALIMENTAIRE
CERTIFICADO SEGÚN: UL1026 (6.ª EDICIÓN) / CSA-22.2 NO. 60335-2-78:14 Y CSA-22.2 NO. 60335-1:11 APARATO ELÉCTRICO DOMÉSTICO PARA COCINAR Y SERVIR ALIMENTOS
WARNING: PLEASE READ THE ENTIRE MANUAL BEFORE INSTALLATION AND USE OF THIS APPLIANCE. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN PROPERTY DAMAGE, BODILY INJURY OR EVEN DEATH.
CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUT RESTRICTIONS AND INSTALLATION INSPECTION REQUIREMENTS IN YOUR AREA.
AVERTISSEMENT : VEUILLEZ LIRE L’INTÉGRALITÉ DU MANUEL AVANT L’INSTALLATION ET L’UTILISATION DE CET APPAREIL. LE NON-RESPECT DE CES INSTRUCTIONS PEUT ENTRAÎNER DES DOMMAGES AUX BIENS, DES
BLESSURES OU MÊME LA MORT. COMMUNIQUEZ AVEC LES AUTORITÉS LOCALES EN MATIÈRE D’INCENDIE ET DE BÂTIMENT CONCERNANT LES RESTRICTIONS ET LES EXIGENCES D’INSTALLATION DANS VOTRE RÉGION.
ADVERTENCI: LEA EL MANUAL COMPLETO ANTES DE INSTALAR Y UTILIZAR ESTE APARATO. INCUMPLIR ESTAS INSTRUCCIONES PODRÍA CAUSAR DAÑOS MATERIALES, LESIONES CORPORALES, E INCLUSO LA MUERTE.
CONSULTE A SUS FUNCIONARIOS LOCALES DE CONSTRUCCIÓN Y CONTROL DE INCENDIOS PARA INFORMARSE SOBRE LAS RESTRICCIONES Y LOS REQUISITOS DE INSPECCIÓN DE INSTALACIONES EN SU REGIÓN.
FOR OUTDOOR AND HOUSEHOLD USE ONLY. NOT FOR COMMERCIAL USE.
RÉSERVÉ À L'USAGE EXTÉRIEUR ET RÉSIDENTIEL UNIQUEMENT. NON DESTINÉ À UN USAGE COMMERCIAL.
SOLO PARA USO EN EXTERIORES Y EN EL HOGAR. NO ES PARA USO COMERCIAL.
ENGLISH
2
.
.
.
Please read and understand this entire manual before attempting to assemble, operate or install the product. This will ensure you
receive the most enjoyable and trouble-free operation of your new smoker. We also advise to retain this manual for future reference.
DANGERS AND WARNINGS
You must contact your local home association, building or fire officials, or authority having jurisdiction, to
obtain the necessary permits, permission or information on any installation restrictions, such as any smoker
being installed on a combustible surface, inspection requirements or even ability to use, in your area.
1. A minimum clearance of 305mm (12 inches) from combustible constructions to the sides of the smoker, and 305mm (12 inches)
from the back of the smoker to combustible constructions must be maintained. Do not install appliance on combustible
floors, or floors protected with combustible surfaces unless proper permits and permissions are obtained by
authorities having jurisdiction. Do not use this appliance indoors or in an enclosed, unventilated area. This wood pellet
appliance must not be placed under overhead combustible ceiling or overhang. Keep your smoker in an area clear and free
from combustible materials, gasoline and other flammable vapors and liquids.
Should a grease fire occur, turn the smoker off and leave the cabinet door closed until the fire is out. Do not
unplug the power cord. Do not throw water on. Do not try to smother the fire. Use of an all-class (class ABC)
approved fire extinguisher is valuable to keep on site. If an uncontrolled fire does occur, call the Fire Department.
2. Keep the unit and electrical supply cords away from water or other liquids. Do not use your smoker in the rain, during an
electrical or around any water source. To protect against electrical shock, use only a properly grounded electrical outlet.
Do not operate the appliance with a damaged cord or plug. If a long, detachable power supply-cord (or extension) is used,
ensure the cord rating is at least as great as the electrical rating of the appliance, and must be a grounded cord. Outdoor
extension cords used with outdoor products are marked with the suffix "W" and with the statement "suitable for use with
outdoor appliances." To reduce the risk of electric shock, keep extension cord connection dry and off the ground.
3. After a period of storage, clean before use. Regular care and maintenance is required to prolong the lifespan of your unit. If
the smoker is stored outside during the rainy season or seasons of high humidity, care should be taken to ensure that water
does not get onto the electric element. Always disconnect the power, before performing any service or maintenance.
Do not transport your smoker while in use or while the smoker is hot. Ensure the smoker is completely cool
to the touch before adjusting the cooking grids, adding wood chips, removing the water tray, moving, or
storing. Store unit indoors when not in use. Do not store the electric smoker with hot ashes inside unit.
Store only when all surfaces are cold.
4. It is recommended to use heat-resistant barbecue mitts and long, sturdy cooking tools when operating the unit. Use caution
when removing food from the smoker. All surfaces are hot, and can remain hot for an extended period after use.
5. Parts of the barbecue may be very hot, and serious injury may occur. Keep young children and pets away while in use.
This appliance is not recommended for children, persons with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they are under direct supervision or instruction
by a person responsible for their safety.
6. Do not use this appliance as a heater, or for anything other than its intended purpose. This unit it not for commercial use.
ENGLISH
3
DISPOSAL OF ASHES
Ashes should be placed in a metal container with a tight-fitting lid. The closed container of ashes should be placed on a non-
combustible floor or on the ground, well away from all combustible materials, pending final disposal. When ashes are disposed by
burial in soil, or otherwise locally dispersed, they should be retained in a closed container until all cinders have thoroughly cooled.
CREOSOTE
Creosote, or soot, is a tar-like substance produced when wood is burned. While burning, it produces black smoke with a residue
which is also black in color. When not removed, it can build to form a thick, hard coating of debris on any surface, posing a threat
to your appliance. It is dangerous to operate this appliance should the flame become very dark and sooty.
Should the creosote ignite, it makes an extremely hot and uncontrolled fire, similar to a grease fire. Should this happen, turn the
unit off, let it cool completely, then inspect for maintenance and cleaning. It commonly accumulates along exhaust areas, such as
a chimney, ventilation damper, or cabinet door.
If creosote has formed within the unit, allow the unit to warm up at a low temperature, turn off the appliance, then wipe away
any formation with a hand towel. Similar to tar, it is much easier to clean when warm, as it becomes liquid.
CARBON MONOXIDE (“ ”)
Burning wood chips gives off carbon monoxide, which has no odor and can cause death. Do not burn wood chips
inside homes, vehicles, tents, garages or any enclosed areas. Use only outdoors where it is well ventilated.
Carbon monoxide is a colorless, odorless, tasteless gas produced by burning gas, wood, propane, charcoal or other fuel. Carbon
monoxide reduces the blood’s ability to carry oxygen. Low blood oxygen levels can result in headaches, dizziness, weakness,
nausea, vomiting, sleepiness, confusion, loss of consciousness or death. Follow these guidelines to prevent this colorless, odorless
gas from poisoning you, your family, or others:
• See a doctor if you or others develop cold or flu-like symptoms while cooking or in the vicinity of the appliance. Carbon
monoxide poisoning, which can easily be mistaken for a cold or flu, is often detected too late.
• Alcohol consumption and drug use increase the effects of carbon monoxide poisoning.
Carbon monoxide is especially toxic to mother and child during pregnancy, infants, the elderly, smokers, and people with blood
or circulatory system problems, such as anemia, or heart disease.
SAFETY LISTING
In accordance with the procedures and specifications listed in the UL1026 (6th Edition) / CSA-22.2 No.
60335-2-78:14 & CSA-22.2 No. 60335-1:11 Electric Household Cooking and Food Serving Appliances. Pit Boss®
Grills electric cooking appliances have been independently tested and listed by CSA (an accredited testing
laboratory) to , , and standards.
300522
The appliance should be supplied through a residual current device (RCD) having a rated residual operat-
ing current not exceeding 30 mA. The appliance is to be connected to a socket-outlet having an earthing
contact (for class I appliances).
ENGLISH
4
Safety Information ..........................................................2
Parts & Specs ...................................................................... 5
Assembly Preparation ...................................................... 6
Operating Instructions
Smoker Environment ................................................................... 8
Smoker Temperature Ranges.....................................................9
Understanding The Control Board ......................................... 10
Understanding The Probes .......................................................11
First Use – Smoker Burn-Off.................................................... 11
Start-Up Procedure .................................................................... 11
Refilling The Water Pan .............................................................12
Refilling The Wood Chip Tray ...................................................12
Shutting Off Your Smoker .........................................................12
Care & Maintenance ........................................................13
Tips & Techniques ............................................................14
Troubleshooting ..............................................................15
Electrical Wire Diagram ..................................................17
Replacement Parts .......................................................... 18
Warranty ............................................................................19
Assembly Instructions ....................................................62
COPYRIGHT NOTICE
Copyright 2022. All right reserved. No part of this manual
may be copied, transmitted, transcribed, stored in a retrieval
system, in any form or by any means without expressed
written permission of,
Dansons
3411 North 5th Avenue, Suite 500, Phoenix, , 85013
www.pitboss-grills.com
Customer Care
USA: (480) 923-9630
Canada (TOLL FREE): 1-877-942-2246
ENGLISH
5
MODEL UNIT ASSEMBLED (WxHxD) UNIT WEIGHT COOKING AREA TEMPERATURE RANGE
31
550mm x 1,190mm x 510mm
/ 21 in. x 46 in. x 20 in.
30 kg
/ 66 lb
Cubic Cooking: 0.07 m3 / 2.7 ft3
TOTAL
- 4,419 cm / 685 sq. in.
38-176°C
/ 100-350°F
Part# Description
1 Cooking Grids (x4)
2 Cooking Grid Support Brackets (x8)
3 Damper Vent (x2)
4 Back Handle (x1)
5 Logo Plate (x1)
6 Cabinet Door Handle (x1)
7 Cabinet Door Latch (x1)
8 Cabinet Door (x1)
9 Main Cabinet (x1)
10 Wood Chip Tray Lid (x1)
11 Wood Chip Tray Assembly (x1)
12 Water Pan (x1)
13 Water Pan Support (x1)
14 Cabinet Base (x1)
15 Support Bar (x1)
16 Support Panel (x2)
17 Meat Probe (x1)
18 Grill Probe Bracket (x1)
19 Power Cord Bracket (x1)
20 Bottom Chamber Assembly (x1)
21 Support Legs (x4)
22 Locking Caster Wheel (x2)
23 Caster Wheel (x2)
24 Grease Tray (x1)
A ¼–20x⅝" Screw (x4)
B ¼–20x½" Screw (x28)
C #10–24x½" Screw (x32)
D #10–24 Lock Nut (x2)
E M5 Locking Washer (x2)
F #5–32x½" Screw (x2)
G Spare Hardware
NOTE: Due to ongoing product development, parts are subject to change without
notice. Contact Customer Care if parts are missing when assembling the unit.
PB – ELECTRIC REQUIREMENTS
110-120V, 60Hz, 1650W, 3-PRONG GROUNDED PLUG
12
5
3
4
11
13
12
15
24
17
23 22
18
21
20 19
16
9
7
8
10
6
14
211
212
213
214
161
162
ENGLISH
6
Parts are located throughout the shipping carton, including underneath the smoker. Inspect the unit, parts, and hardware blister
pack after removing from the protective shipping carton. Discard all packaging materials from inside and outside of the griddle
before assembly, then review and inspect all parts by referencing the parts list. If any part is missing or damaged, do not attempt
to assemble. Shipping damage is not covered under warranty. Contact your dealer or Pit Boss® Grills Customer Care for parts.
service@pitboss-grills.com | USA: (480) 923-9630 | CANADA (TOLL FREE): 1-877-942-2246
IMPORTANT: To ease installation, using two people is helpful (but not necessary) when assembling this unit.
Tools required for assembly: screwdriver and level.
Tools not included.
62 .
IMPORTANT
- It is advised to review each step entirely before starting assembly on instructions.
-Hardware combination involving a locking washer and washer should be installed with the locking washer closest to the
head of the screw.
-Tighten screws completely after all screws for that step have been installed.
1 The four support legs must be arranged correctly to properly install the support panels and support bar in later steps.
2 Ensure that all screws on the cabinet base are fully-tighten to avoid screws falling out when the unit is moved.
3
Once the Grill Probe bracket is secure, ensure the stainless steel tip extends above the lip of the lower cabinet. This reads
the internal temperature of the main cabinet. Incorrect placement of the Grill Probe may result in wrong temperature
readings on the Control Board.
4 To change the height between each cooking grid, adjust only when the smoker is completely cooled to avoid injury.
NOTE
1 Install Locking Caster Wheels (Part #22) to Support Legs (Part #21-2 & 21-4) as shown in Step 2 of assembly.
2The support bracket with two holes along the bottom should be on the same side of the unit as the power cord exits the
control board (left side). This is important for later steps.
3 Repeat the Support Panel installation for the opposite legs.
Loosen the screw of the power cord clip on the support leg, and guide the power cord through the power cord clip to
secure.
5Keep water in the water pan at all times while cooking. It will catch grease and drippings from your cooks and allow for
easier clean up. If smoking for an extended period, move water pan up higher to allow water to last longer.
The logo plate is supplied with one washer and one wing nut.
Unscrew the pre-installed screws from the handle. Place the Wood Chip Tray Lid on top of the Wood Chip Tray base.
Secure the assembly with the screws shown in the illustration: base + lid, faceplace, and the handle.
ENGLISH
7
•
This appliance requires 110-120 volt, 60Hz, 1650w. It must be a 3-prong
grounded plug. Ensure grounded end is not broken off before use.
•
This appliance will work on most GFCI outlets, with a recommended
size of 15 or 20 amp service. If your GFCI outlet is highly sensitive to
power surges, it will likely trip during the start-up phase of operation.
During the start-up phase, the element draws 200-700 watts of
electricity which can be too much power for a GFCI outlet to handle.
Each time it trips, it increases in sensitivity. If the GFCI keeps tripping,
replace the outlet or change to a non-GFCI outlet.
IMPORTANT: Disconnect unit from power source when not in use.
ENGLISH
8
With today’s lifestyle of striving to eat healthy and nutritious foods, a factor to consider is the importance of reducing fat intake.
One of the best ways to cut down on fats in your diet is to use a savory method of cooking like smoking. As this electric smoker
uses wood chips for smoking, the natural wood flavor is infused into the meats, reducing the need for high sugar-based sauces.
1.
With all outdoor appliances, outside weather conditions play a big part in the performance of your smoker and the cooking
time needed to perfect your meals. All Pit Boss® units should keep a minimum clearance of 305mm (12 inches) from combustible
constructions, and this clearance must be maintained while the smoker is operational. This appliance must not be placed under
overhead combustible ceiling or overhang. Keep your smoker in an area clear from combustible materials, gasoline and other
flammable vapors and liquids.
2.
As it becomes cooler outside, that does not mean that smoking season is over! The crisp cool air and heavenly aroma of
smoked foods will help cure your winter blues. Follow these suggestions on how to enjoy your smoker throughout the cooler
months:
• If smoking at low temperatures fails, increase the temperature slightly to achieve the same results.
• Organize – Get everything you require ready in the kitchen before you head outdoors. During the winter, move your
smoker to an area that is out of the wind and direct cold. Check local bylaws regarding the proximity of your smoker
in relation to your home and/or other structures. Put everything you need on a tray, bundle up tight, and get it done!
• To help keep track of the outside temperature, place an outdoor thermometer close to your cooking area. Keep a log
or history of what you cooked, the outdoor temperature, and the cooking time. This will help later down the road to
help you determine what to cook and how long it will take.
• In very cold weather, increase your preheating time by at least 20 minutes.
• Avoid opening the smoke cabinet door any more than necessary. Cold gusts of wind can completely cool your internal
temperature. Be flexible with your serving time; add extra cooking time each time you open the door.
• Have a heated platter or a dish cover ready to keep your food warm while making the trip back inside.
• Ideal foods for winter cooking are those that require little attention, such as roasts, whole chickens, ribs, and turkey.
Make your meal preparation even easier by adding simple items such as vegetables and potatoes.
3.
As it becomes warmer outdoors, the cooking time will decrease. Proper dress is important when it gets really hot: shorts,
shirt, shoes, hat, apron and a generous slab of suntan lotion is recommended. Follow these few suggestions on how to enjoy
your smoker throughout the hot months:
• Adjust your cooking temperatures downward. This helps to avoid unwanted flare-ups.
• Use a meat thermometer to determine the internal temperature of your foods. This helps in preventing your meat
from over cooking and drying out.
• Even in hot weather, keep the smoke cabinet door closed at all times.
• You can keep foods hot by wrapping them in foil, and placing them in an insulated cooler. Stuff crumpled up
newspaper around the foil and this will keep food hot for 3 to 4 hours.
ENGLISH
9
Temperature readouts on the control board may not exactly match a meat thermometer. All temperatures listed below
are approximate and are affected by the following factors: outside ambient temperature, the amount and direction
of wind, the quality of wood chips being used, the cabinet door being opened, and the quantity of food being cooked.
•
135176° / 275350°
This range is best for baking, roasting, and finishing off that slow smoked creation. Cooking at these temperatures will
greatly reduce the chances of a grease flare-up. Great range for cooking anything wrapped in bacon, or where you want
versatility with control.
•
38122° / 100250°
This range is used to slow roast, increase smoky flavor, and to keep foods warm. Infuse more smoke flavor and keep your
meats juicy by cooking longer at a lower temperature (also known as
low and slow
). Highly recommended for the big turkey
at Thanksgiving, juicy ham at Easter, or the huge holiday feast.
Smoking is a variation on true barbecuing and is truly the main advantage of a smoker. There are two types of smoking: hot
smoking and cold smoking.
•
Hot smoking
, another name for
low and slow
cooking, is generally done at 82-122C / 180-250F. Hot smoking
works best when longer cooking time is required, such as large cuts of meats, fish, or poultry.
•
Cold smoking
is when the food is located so far away from the heat source that it smokes without cooking, and at
temperatures of 15-32C / 60-90F.
TIP: To intensify that savory flavor, smoke your foods before turning up the heat to fully-cook your meats. This
allows the smoke to penetrate the meats, before the pores of the meat close at 49°C / 120°F.
The key is to experiment with the length of time you allow for smoking, before the meal is finished cooking. Some outdoor
chefs prefer to smoke at the end of a cook, allowing the food to keep warm until ready to serve. Practice makes perfect!
ENGLISH
10
PROBE 1
ACTUAL
FC
COOK
FC
PROBE 2
FC
Element
Temp Set/Act
Time Smoke
F/C
When connected to a power source, the Power Button will glow blue. Press the Power Button to power on the unit. Once
the Power Button is pressed, the Digital LCD Screen will light up, displaying that it is ready to operate. Press and hold
the button for three seconds to turn the unit off.
PROBE 1
ACTUAL
FC
COOK
FC
PROBE 2
FC
Element
Temp Set/Act
Time Smoke
F/C The Temperature Switch Button is used to change the temperature readout on the Digital LCD Screen. Press the button
to switch to Celsius (ºC) or to Fahrenheit (ºF), as preferred. Default is set to Fahrenheit.
PROBE 1
ACTUAL
FC
COOK
FC
PROBE 2
FC
Element
Temp Set/Act
Time Smoke
F/C
The Element Light Indicator is used to display if the heating element is on or off. If the light glows, the heating element
is working and is on. If the light is off, the element is off. The heating element will stay on if the temperature
is below the temperature. Once the temperature is reached, the heating element will automatically turn off.
PROBE 1
ACTUAL
FC
COOK
FC
PROBE 2
FC
Element
Temp Set/Act
Time Smoke
F/ C
The Digital LCD Screen is used as the information center for your unit. The Digital LCD screen will display your Desired
Cook Temperature (), Actual Cook Temperature (), Meat Probe Temperature (if connected), and any error
messages. If only one Meat Probe is connected, only one reading will be displayed. Temperature can be displayed in
either Fahrenheit or Celsius.
PROBE 1
ACTUAL
FC
COOK
FC
PROBE 2
FC
Element
Temp Set/Act
Time Smoke
F/C
PROBE 1
ACTUAL
FC
COOK
FC
PROBE 2
FC
Element
Temp Set/Act
Time Smoke
F/C
The Adjustment Arrows allow you to increase or decrease the and on the Control Board. Press and hold the
buttons to increase or decrease the value faster.
PROBE 1
ACTUAL
FC
COOK
FC
PROBE 2
FC
Element
Temp
Set/Act
Time Smoke
F/C
Press the Button on the Control Board to adjust the cooking temperature.
• Press once to select the temperature setting, then the adjustment arrows to change the temperature in five-degree
increments. Press once again to lock-in the temperature setting once the changes are finished.
The heating element will not turn on until is also set. Default element temperature is set to 37ºC / 100 ºF.
PROBE 1
ACTUAL
FC
COOK
FC
PROBE 2
FC
Element
Temp Set/Act
Time
Smoke
F/C
Press the Button on the Control Board to adjust the cooking time.
• Press once to select the time setting, then press the adjustment arrows to change the hours. Changes are in 1
hour increments (ranging from 00-99).
• Press once again to select the minutes setting, then press the adjustment arrows to change the minutes. Changes
are in 10 minute increments (ranging from 00-50).
• Press twice to lock in the time setting once the changes are finished.
PROBE 1
ACTUAL
FC
COOK
FC
PROBE 2
FC
Element
Temp
Set/Act
Time Smoke
F/C
Press the / Button on the Control Board to display the desired setpoint (SET) or the actual/current (ACT) time and
temperature. The display shows the actual (ACT) settings for TIME and TEMP by default.
• To view the TIME and TEMP setpoints, press the / button once. After 15 seconds, the display will switch
back to the actual (ACT) settings.
• To change a setpoint, press the / button once, followed by pressing TIME or TEMP. Next. press the
adjustment arrows to change the setting.
PROBE 1
ACTUAL
FC
COOK
FC
PROBE 2
FC
Element
Temp Set/Act
Time
Smoke
F/C
Press the Button on the Control Board to manually turn on the heating element for a 20-minute cycle. "FS" will
appear on the screen, indicating "Fast Smoke". This is mostly used to recover lost smoke from opening the cabinet door,
or when starting a new smoke profile with freshly added wood chips.
• To stop the cycle before the 20 minutes, press the SMOKE Button twice.
PROBE 1
ACTUAL
FC
COOK
FC
PROBE 2
FC
Element
Temp Set/Act
Time Smoke
F/ C
ENGLISH
11
PRIME SMOKE
150º 400º
HIGH
175º 350º
200º 300º
225º 250º
PROBE 1
ACTUAL
F
C
COOK
FC
PROBE 2
F
C
PELLET VERTICAL SMOKER
-COPPERHEAD (WALMART)
F / C
The plug-in connection port(s) on the front of the Control Board are for two Meat Probes. When a meat
probe is connected, the temperature is displayed on the LCD Screen. When not in use, disconnect the
meat probe from the connection port. Compatible with Pit Boss® branded meat probes only. Additional
meat probe(s) sold separately.
•
Located inside the cabinet, on the rear wall along the bottom, is the Grill Probe. It is a small, vertical piece of stainless steel.
The Grill Probe measures the internal temperature of the unit. When the temperature is adjusted on the Control Board, the Grill
Probe will read the actual temperature inside the unit and adjust to the desired temperature.
IMPORTANT: The temperature of your unit is highly affected on ambient outdoor weather and the quantity of
food being cooked.
•
The meat probe measures the internal temperature of your meat in the smoker, similar to your indoor oven. Plug-in the meat
probe adapter to the meat probe connection port and insert the stainless steel meat probe into the thickest portion of your
meat and the temperature will be displayed on the Control Board. To ensure the meat probe is connected properly to
the connection port, feel and hear it snap into place.
IMPORTANT: When placing the meat probe into your meat, ensure the meat probe and meat probe wires avoid
direct contact with the heating element. This can result in damage to your meat probe. Run the excess wire out
the main cabinet door, along the edge. When not in use, disconnect the meat probe(s) from connection ports, and
place aside to keep protected and clean.
Before using your smoker for the first time with food, it is important to complete a burn-off to cure the interior and exterior
finish of your unit. Start the smoker and operate at any temperature over (177°C / 350°F) with the cabinet door closed for 30 to
40 minutes to burn-off the unit and rid it of any foreign matter.
: Curing your smoker is important for its long-term operation and care. If the burn-off is not performed, the
exterior finish will not set properly, as well as a paint odor can impart unnatural flavors onto your first prepared meal.
1. Open the cabinet door and carefully ¾ fill the water pan with water or marinade.
IMPORTANT: Do not fill completely or overfill the water pan, as this could damage your electrical element and/
or parts while the smoker is in use.
2. Adjust cooking grids and grid support brackets to desired height for the foods you intend to smoke. Once satisfied with
the height of your grids, close the cabinet door.
3. Remove the wood chip tray. Open the wood chip tray lid, add wood chips, then slide back into the front of the cabinet.
NOTE: We recommend using wood chips, not wood chunks, as wood chips are smaller and easier to fit inside the
wood chip tray.
4. Plug the power cord into a grounded power source. The Power Button will glow blue to indicate there is power.
5. With the cabinet door closed, press the Power Button to turn on the unit and the Digital LCD Screen will light up,
displaying that it is ready to operate.
6. Preheat your grill:
• Open both damper vents completely on the backside of the unit.
• Press the / Button, then the
button on the Control Board twice to select the time setting, and press
the Adjustment Arrows to 20 minutes. Press the
button twice again to lock-in the time setting once the
changes are finished.
ENGLISH
12
• Press the / Button, then the
button on the Control Board once to select the temperature setting,
and press the Adjustment Arrows to a minimum of 121°C / 250°F. Press the
button once again to lock-in the
temperature setting once the changes are finished. The smoker will begin to smoke while preheating.
TIP: Keep the damper vents partially or completely open when cooking at lower temperatures; close the damper
vents when using higher cooking temperatures.
7. After preheating is complete, you will notice that your wood chips will be smoking. You are ready to enjoy your smoker
at your desired time and temperature! Slide out and place food on the cooking grids, leaving room between each item to
allow smoke and moisture to circulate evenly.
IMPORTANT: When selecting a low temperature setting after preheating, allow time for the smoker temperature
to decrease and stabilize at the new desired temperature.
ELECTRICAL ELEMENT FAILURE PROCEDURE
If for any reason your electric element fails to operate, follow
Troubleshooting
instructions
.
Check the water level periodically during your cooking session and add water if needed.
1. Wearing heat-resistant barbecue mitts, open the cabinet door.
2. Carefully refill the water pan with water or marinade until it is ¾ full. Close the cabinet door.
IMPORTANT: Do not fill completely or overfill the water pan, as this could damage your electrical element and/
or parts while the smoker is in use.
Check your wood chip tray periodically during your cooking session and add more wood chips if needed.
1. Wearing heat-resistant barbecue mitts, remove the wood chip tray from the opening above the control board on the
front panel of the unit.
2. Carefully open the lid, and refill the wood chip tray with new wood chips. Close the lid once full.
3. Replace the wood chip tray into the front panel of the smoker.
4. Press the Button on the Control Board to manually turn on the heating element. This is used to increase the level
of smoke after opening the door, or can be used to assist start smoking fresh wood chips
NOTE: Use hardwood wood chips that have been seasoned, such as pecan, hickory, oak, apple, cherry, alder,
mesquite or a competition blend. It is not necessary to soak the wood chips prior to smoking, as hardwoods
have natural moisture in the wood that will release as it heats up and combusts. Do not use resin woods like
pine or cedar in your smoker.
1. When finished cooking, press and hold the Power Button for three seconds to turn the unit off. The electric element will
turn off, and the wood chips will stop smoking.
TIP: If you have been preparing foods that are extra greasy, allow the smoker to burn-off for an extra 10 to 20
minutes to a minimum temperature of 177°C / 350°F with the cabinet door closed.
ENGLISH
13
Any Pit Boss® unit will give you many years of flavorful service with minimum cleaning. Follow these cleaning and maintenance
tips to service your smoker:
1.
• A meat probe not in use should be rolled up in a large, loose coil. Kinks or folds in the wire may cause damage.
• Although both the Grill Probe and meat probe are stainless steel, do not place either in the dishwasher or submerge in
water. Water damage to the internal wires will cause a probe to short-out, causing false readings. If a probe is damaged,
it should be replaced.
2.
• It is recommended to clean your wood chip tray after every few uses. This will ensure proper smoking of new wood
chips and avoid any hard build-up of debris or ash.
• Use a long-handled grill cleaning brush, remove any food or build-up from the cooking grids. Best practice is to
do this while they are still warm from the previous cook. Grease fires are caused by too much fallen debris on
the cooking components of the smoker. Clean the inside of your smoker on a consistent basis. In the event you
experience a grease fire, keep the cabinet door and damper vents closed to choke out the fire. If the fire does not
go out quickly, carefully remove the food, turn the smoker off, and shut the cabinet door until the fire is completely
out. Lightly sprinkle baking soda, if available. Check your grease tray often, and clean out as necessary. Keep in mind
the type of cooking you do.
IMPORTANT: The water pan may accumulate grease. Refill and replace the water in the water pan often.
• The glass of the cabinet door is tempered and will not break with high heat; however, excessive build-up may cause
the door to not close if not cleaned regularly. Smoke and debris can be removed with frequent cleaning of the glass.
3.
• Wipe your smoker down after each use. Use warm soapy water to cut the grease. Do not use oven cleaner, abrasive
cleansers or abrasive cleaning pads on the outside grill surfaces. All painted surfaces are not covered under
warranty, but rather are part of general maintenance and upkeep. For paint scratches, wearing, or flaking of the
finish, all painted surfaces can be touched up using high heat BBQ paint.
• Use a cover to protect your smoker for complete protection! A cover is your best protection against weather and
outside pollutants. When not in use or for long-term storage, keep the unit under a cover in a garage or shed.
CLEANING FREQUENCY TIME TABLE (NORMAL USE)
ITEM CLEANING FREQUENCY CLEANING METHOD
Cabinet Glass Door Every 2-3 Smoke Sessions Mix Baking Soda & Vinegar, Scrub with Steel Wool (Fine)
Bottom of Cabinet Every 5-6 Smoke Sessions Scoop Out, Wet/dry vacuum Excess Debris
Wood Chip Tray Every 2-3 Smoke Sessions Scoop Out, Wet/dry vacuum Excess Debris
Cooking Grids After Each Smoke Session Burn Off Excess, Grill Cleaning Brush
Water Pan After Each Smoke Session Scrub Pad & Soapy Water
Grease Tray After Each Smoke Session Scrub Pad & Soapy Water
Electric Element Twice A Year Dust, Wipe Element with Soapy Water
Grill Probe Every 2-3 Smoke Sessions Scrub Pad & Soapy Water
Meat Probe After Each Use Scrub Pad & Soapy Water
ENGLISH
14
Follow these helpful tips and techniques, passed on from Pit Boss® owners, our staff, and customers just like you, to become more
familiar with your smoker:
1.
• Keep everything in the kitchen and cooking area clean. Use different platters and utensils for the cooked meat than
the ones you used to prepare or transport the raw meat out to the smoker. This will prevent cross contamination of
bacteria. Each marinade or basting sauce should have its own utensil.
• Keep hot foods hot (above 60ºC / 140ºF), and keep cold foods cold (below 3ºC / 37ºF).
• A marinade should never be saved to use at a later time. If you are going to use it to serve with your meat, be sure
to bring it to a boil before serving.
• Cooked foods should not be left out in the heat for more than an hour. Do not leave hot foods out of refrigeration
for more than two hours.
• Defrost and marinade meats by refrigeration. Do not thaw meat at room temperature or on a counter top. Bacteria
can grow and multiply rapidly in warm, moist foods. Wash hands thoroughly with hot, soapy water before starting
any meal preparation and after handling fresh meat, fish and poultry.
2.
• Be prepared, or
Mise en Place
. This refers to preparing the cooking recipe, fuel, accessories, utensils, and all
ingredients you require at your side before you start cooking. Also, read the entire recipe, start to finish, before
lighting the smoker.
• A BBQ floor mat is very useful. Due to food handling accidents and cooking splatter, a BBQ floor mat would protect
a deck, patio, or stone platform from the possibility of grease stains or accidental spills.
3.
• To infuse more smoke flavor into your meats, cook longer and at lower temperatures (also known as
low and slow
).
Meat will close its fibers after it reaches an internal temperature of 49ºC / 120ºF. Misting, or mopping, are great ways
to keep meat from drying out.
• Always use a meat thermometer to determine the internal temperature of the foods you are cooking. Smoking foods
with hardwood wood chips will turn meats and poultry pink. The band of pink (after cooking) is referred to as a
smoke ring
and is highly prized by outdoor chefs.
• Sugar-based sauces are best applied near the end of cooking to prevent burning and flare-ups.
• Leave open space between the foods and the extremities of the cabinet for proper heat flow. Food on a crowded
smoker will require more cooking time.
• Use a set of long-handled tongs for turning meats, and a spatula for softer items like fish and cheese. Using a
piercing utensil, such as a fork, will prick the meat and allow the juices to escape.
• Foods in deep casserole dishes will require more time to cook than a shallow baking pan.
• It’s a good idea to put cooked food onto a heated platter, keeping the food warm. Red meats, such as tenderloins
and roasts, benefit from resting for several minutes before serving. It allows the juices that were driven to the
surface by heat to ease back to the center of the meat, adding more flavor.
ENGLISH
15
Proper cleaning and maintenance will prevent common operational problems. When your Pit Boss® smoker is operating poorly, or
used less frequently, the following troubleshooting tips may be helpful.
For FAQ, please visit
www.pitboss-grills.com
. You may also contact your local Pit Boss® authorized dealer or contact Customer
Care for assistance.
WARNING: Always disconnect the electrical cord prior to opening the smoker for any inspection, cleaning,
maintenance or service work. Ensure the digital electric smoker is completely cooled to avoid injury.
No Power Lights On
The Control Board
Power Button Press the Power Button. Try another attempt and hold for two seconds to verify connection.
Not Connected To Power
Source
Ensure smoker is plugged into a working power source. Reset breaker. Ensure GFCI is the correct power
supply (see
Electric Wire Diagram
for access to electric components). Ensure all wire connections are
firmly connected and dry.
Faulty Control Board Control Board needs to be replaced. Contact Customer Care for a replacement part.
Power Light
Not On
Unit Not Turned On Press the Power Button. Try another attempt and hold for two seconds to verify connection.
Faulty Control Board Control Board needs to be replaced. Contact Customer Care for a replacement part.
No Display On
Control Board, Power
Light Is On
Faulty Control Board Control Board needs to be replaced. Contact Customer Care for a replacement part.
Element (Heating)
Light Not On
TEMP / TIME Not Set Set the TEMP and TIME on the Control Board to turn on the heating element light.
Faulty Control Board Control Board needs to be replaced. Contact Customer Care for a replacement part.
TEMP / TIME Will Not
Adjust
Faulty Control Board Control Board needs to be replaced. Contact Customer Care for a replacement part.
Temperature In Main
Cabinet Is Inaccurate
Temperature
Probe Is Dirty
Follow
Care and Maintenance
instructions.
Grill Probe Not Making
Connection.
Access the electrical components on the base of the unit (see
Electric Wire Diagram
) and check for
any damage to the Grill Probe wires. Ensure Grill Probe spade connectors are firmly connected, and
connected correctly, to the Control Board.
Faulty Control Board Control Board needs to be replaced. Contact Customer Care for a replacement part.
Unit Takes Too Long
/ Excessive Time
To Achieve Desired
Temperature
Cold Climate Outdoor temperature is below 65°C / 18°F, so the unit may take extended heating time.
Extension Cord Used Using an extension cord may reduce the power supply to the unit. Plug the appliance directly into
power source or ensure maximum length extension cord is 7.6 meters / 25 feet, minimum gauge 12/3.
Cabinet Is Too Packed There is too much food in the cabinet. Place food on the cooking grids, leaving room between each
item to allow smoke and moisture to circulate evenly.
Door Not Closed Ensure door is closed, seal is not damaged, and the door latch is secure.
Water Pan Not Properly
Located
Check the water pan to ensure it is sitting properly on the support brackets. See
Assembly
Instructions
for further instruction.
Faulty Control Board Control Board needs to be replaced. Contact Customer Care for a replacement part.
Door Not Closing
Properly
Poor Door Alignment Adjust door hinges to ensure that door is mounted correctly. See
Assembly Instructions.
Damaged Door Seal Door needs to be replaced. Contact Customer Care for a replacement parts.
ENGLISH
16
Grease Leaking From
Cabinet Door
Door Not Closing
Properly
Ensure door is closed, seal is not damaged, and the door latch is secure.
Unit Not Level Move unit to a level cooking surface. Ensure that there is no damage to the support legs.
Grease Tray Is Full Empty grease tray and re-install. Follow
Care and Maintenance
instructions.
No Smoke Is Being
Produced
No Wood Chips Add wood chips to the wood chip tray.
Element Times Out, Not
Enough Heat To Wood
Chips
The heating element is not staying on long enough to heat the wood chips, which is due to the TEMP
being set too low. First, open the rear vents completely to promote airflow. Next, reset TEMP higher to
turn on the element for 20 minutes.
Damaged Wood
Chip Tray
Wood chip tray needs to be replaced. Contact Customer Care for a replacement parts.
"noP" Error Code Bad Connection At
Connection Port
Disconnect meat probe from connection port on the Control Board, and reconnect. Ensure the meat
probe adapter is firmly connected. Check for signs of damage to the adapter end. If still failed, call
Customer Care for replacement part.
Meat Probe Damaged Check for signs of damage to the wires of the meat probe. If damaged, call Customer Care for
replacement part.
Faulty Control Board Control Board needs to be replaced. Contact Customer Care for a replacement part.
"Er1" Error Code The Smoker Is Too Cold
To Function
Outdoor temperature is too cold for the heating element to function. Move smoker to warmer
location and retry. If element still fails after multiple attempts, call Customer Care for assistance.
"ErH" Error Code The Smoker Has
Overheated / Exceeded
315°C / 600°F
Press and hold the Power Button for three seconds to turn the unit off, and allow smoker to cool.
Follow
Care and Maintenance
instructions. After maintenance, press the Power Button to turn the
unit on, then select desired temperature. If error code still displayed, contact Customer Care.
"ErR" Error Code Grill Probe Wire Not
Making Connection.
Access the electrical components on the base of the unit (see
Electric Wire Diagram
) and check for
any damage to the Grill Probe wires. Ensure Grill Probe spade connectors are firmly connected, and
connected correctly, to the Control Board.
Grill Probe Check status of Grill Probe. Follow
Care and Maintenance
instructions if dirty. Contact Customer Care
for a replacement part if damaged.
ENGLISH
17
The Control Board system is an intricate and valuable piece of technology. For protection from power surges and electrical shorts,
consult the wire diagram below to ensure your power source is sufficient for the operation of the unit.
PB – ELECTRIC REQUIREMENTS
110-120V, 60Hz, 1650W, 3-PRONG GROUNDED PLUG
: Electrical components, passed by product safety testing and certification services, comply
with a testing tolerance of ± 5-10 percent.
INDEX
W : WHITE
R : RED
K : BLACK
G : GROUND
GROUNDED
POWER CORD
VW-1, 105°C/221°F,
18-3 STANDARD CSA
TEMPERATURE
PROBE
GRILL PROBE MOLEX
CONNECTORS
EXTERIOR VIEW
CONTROL BOARD
INTERIOR VIEW
GROUND
HEATING ELEMENT
110-120V, 1650W
K
W
G
G
W
R
ENGLISH
18
Part# Description
1 Cooking Grids (x4)
2 Cooking Grid Support Brackets (x8)
3 Damper Vent (x2)
4 Back Handle (x1)
5 Logo Plate (x1)
6 Cabinet Door Handle (x1)
7 Cabinet Door Latch (x1)
8 Cabinet Door (x1)
9 Main Cabinet (x1)
10 Wood Chip Tray Lid (x1)
11 Wood Chip Tray Assembly (x1)
12 Water Pan (x1)
13 Water Pan Support (x1)
14 Cabinet Base (x1)
15 Support Bar (x1)
16 Support Panel (x2)
17 Meat Probe (x1)
18 Grill Probe Bracket (x1)
19 Power Cord Bracket (x1)
20 Bottom Chamber Assembly (x1)
21 Support Legs (x4)
22 Locking Caster Wheel (x2)
23 Caster Wheel (x2)
24 Grease Tray (x1)
25 ¼–20x⅝" Screw (x4)
26 ¼–20x½" Screw (x28)
27 #10–24x½" Screw (x32)
28 #10–24 Lock Nut (x2)
29 M5 Locking Washer (x2)
30 #5–32x½" Screw (x2)
NOTE: Due to ongoing product development, parts are subject to change without
notice.
1 2
5
3
4
11
13
12
15
24
17
23
22
18 21
20
19
16
9
7
8
10
6
14
211
212
213
214
161
162
27
26
25
29
30
28
ENGLISH
19
CONDITIONS
All electric smokers by Pit Boss®, manufactured by Dansons, carry a limited warranty from the date of sale by the original owner.
The warranty coverage begins on the original date of purchase and proof of date of purchase, or copy of original bill of sale, is
required to validate the warranty. Customers will be subject to parts, shipping, and handling fees if unable to provide proof of
the purchase or after the warranty has expired.
Dansons carries a five (5) year warranty against defects and workmanship on all parts, and five (5) year on electrical components.
Dansons warrants that all part(s) are free of defects in material and workmanship, for the length of use and ownership of the
original purchaser. Warranty does not cover damage from wear and tear, such as scratches, dents, dings, chips or minor cosmetic
cracks. These aesthetic changes of the smoker do not affect its performance. Repair or replacement of any part does not extend
past the limited warranty beyond the five (5) year from date of purchase. During the term of the warranty, Dansons’ obligation
shall be limited to furnishing a replacement for defective and/or failed components. As long as it is within the warranty period,
Dansons’ will not charge for repair or replacement for parts returned, freight prepaid, if the part(s) are found by Dansons’ to
be defective upon examination. Dansons’ shall not be liable for transportation charges, labor costs, or export duties. Except as
provided in these conditions of warranty, repair or replacement of parts in the manner and for the period of time mentioned
heretofore shall constitute the fulfillment of all direct and derivate liabilities and obligations from Dansons to you. Dansons takes
every precaution to utilize materials that retard rust. Even with these safeguards, the protective coatings can be compromised
by various substances and conditions beyond Dansons’ control. High temperatures, excessive humidity, chlorine, industrial fumes,
fertilizers, lawn pesticides and salt are some of the substances that can affect metal coatings. For these reasons, the warranty
does not cover rust or oxidization, unless there is loss of structural integrity on the smoker component. Should any of the above
occur, kindly refer to the care and maintenance section to prolong the lifespan of your unit. Dansons recommends the use of a
cover when the smoker is not in use.
This warranty is based on normal domestic use and service of the smoker and neither limited warranty coverage’s apply for a
smoker which is used in commercial applications.
There is no written or implied performance warranty on Pit Boss® smokers, as the manufacturer has no control over the installation,
operation, cleaning, maintenance or the type of fuel burned. This warranty will not apply nor will Dansons assume responsibility if
your appliance has not been installed, operated, cleaned and maintained in strict accordance with this owner’s manual. Any use of
gas not outlined in this manual may void the warranty. The warranty does not cover damage or breakage due to misuse, improper
handling or modifications. Neither Dansons, or authorized Pit Boss® dealer, accepts responsibility, legal or otherwise, for the incidental
or consequential damage to the property or persons resulting from the use of this product. Whether a claim is made against Dansons
based on the breach of this warranty or any other type of warranty expressed or implied by law, the manufacturer shall in no event
be liable for any special, indirect, consequential or other damages of any nature whatsoever in excess of the original purchase of this
product. All warranties by manufacturer are set forth herein and no claim shall be made against manufacturer on any warranty or
representation. Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations of implied
warranties, so the limitations or exclusions set forth in this limited warranty may not apply to you. This limited warranty gives you
specific legal rights and you may have other rights, which vary from state to state.
To order replacement parts, please contact your local Pit Boss® dealer or visit our online store at: www.pitboss-grills.com
If you have any questions or problems, contact Customer Care:
service@pitboss-grills.com | USA: (480) 923-9630 | CANADA (TOLL FREE): 1-877-942-2246
ENGLISH
20
Contact your nearest Pit Boss® dealer for repair or replacement parts. Dansons requires proof of purchase to establish a warranty
claim; therefore, retain your original sales receipt or invoice for future reference. The serial and model number of your Pit Boss®
can be found on the back of the unit. Record information below as the label may become worn or illegible.
MODEL SERIAL NUMBER
DATE OF PURCHASE AUTHORIZED DEALER
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
Pit Boss 3-Series Digital Electric Smoker Manuel utilisateur
- Catégorie
- Outils de jardin
- Taper
- Manuel utilisateur
