WARNING: Please read the entire manual before installation and use of this electric, pellet fuel-burning appliance. Failure to follow these instructions could result in property damage, bodily injury or even
death. Contact local building or fire officials about restrictions and installation inspection requirements in your area.
AVERTISSEMENT : Veuillez lire l’intégralité du manuel avant l’installation et l’utilisation de cet appareil électronique à granules. Le non-respect de ces instructions peut entraîner des dommages aux biens, des
blessures ou même la mort. Communiquez avec les autorités locales en matière d’incendie et de bâtiment concernant les restrictions et les exigences d’installation dans votre région.
ADVERTENCIA: Por favor, lea todo el manual antes de la instalación y el uso de este eléctrico, que quema combustible de pellets. aparato. El incumplimiento de estas instrucciones podría resultar en daños a
la propiedad, lesiones corporales o incluso la muerte. Comuníquese con los funcionarios locales de construcción o bomberos acerca de las restricciones y los requisitos de inspección de instalación en su área.
| |
5005166
/ / 71
/ / 10912
WOOD PELLET
SMOKER (7-SERIES)
IMPORTANT, READ CAREFULLY, RETAIN FOR FUTURE
REFERENCE. MANUAL MUST BE READ BEFORE OPERATING!
FUMEUR VERTICAL À
GRANULÉS DE BOIS
(SÉRIE 7)
IMPORTANT, PRENEZ CONNAISSANCE
DE CE DOCUMENT ET CONSERVEZ-LE POUR RÉFÉRENCE
ULTÉRIEURE VOUS DEVEZ LIRE CE GUIDE AVANT D’UTILISER
LE BARBECUE !
AHUMADOR DE PELLETS
DE MADERA (SERIE 7)
IMPORTANTE, LEA ATENTAMENTE, CONSERVE
PARA FUTURA REFERENCIA. MANUAL DEBE
SER LEÍDO ANTES DE OPERAR!
. .
' . .
. .
71
ENGLISH
2
.
.
Please read and understand this entire manual before attempting to assemble, operate or install the product. This will ensure you
receive the most enjoyable and trouble-free operation of your new wood pellet smoker. We also advise you retain this manual
for future reference.
DANGERS AND WARNINGS
You must contact your local home association, building or fire officials, or authority having jurisdiction, to
obtain the necessary permits, mission or information on any installation restrictions, such as any smoker
being installed on a combustible surface, inspection requirements or even ability to use, in your area.
1. A minimum clearance of 305mm (12 inches) from combustible constructions to the sides of the smoker, and 305mm (12 inches)
from the back of the smoker to combustible constructions must be maintained. Do not install appliance on combustible
floors, or floors protected with combustible surfaces unless proper permits and permissions are obtained by
authorities having jurisdiction. Do not use this appliance indoors or in an enclosed, unventilated area. This wood pellet
appliance must not be placed under overhead combustible ceiling or overhang. Keep your smoker in an area clear and free
from combustible materials, gasoline and other flammable vapors and liquids.
Should a grease fire occur, turn the smoker OFF and leave the lid closed until the fire is out. Unplug the
power cord from the connected outlet. Do not throw water on the unit. Do not try to smother the fire. Use
of an all-class (class ABC) approved fire extinguisher is valuable to keep on site. If an uncontrolled fire does
occur, call the Fire Department.
2. Keep electrical supply cords and the fuel away from heated surfaces. Do not use your smoker in the rain or around any water source.
3. After a period of storage, or non-use, check the burn grate for obstructions, the hopper for foreign objects, and any air
blockage around the fan intake, chimney, or rear barrel exhaust holes. Clean before use. Regular care and maintenance is
required to prolong the lifespan of your unit. If the smoker is stored outside during the rainy season or seasons of
high humidity, care should be taken to insure that water does not get into the hopper. When wet or exposed to high
humidity, wood pellets will expand greatly, decompose, and may jam the feed system. Always disconnect the power, before
performing any service or maintenance.
Do not transport your smoker while in use or while the smoker is hot. Ensure the fire is completely out and
that the smoker is completely cool to the touch before moving.
4. It is recommended to use heat-resistant barbecue mitts or gloves when operating the smoker. Do not use accessories not
specified for use with this appliance. Do not put a barbecue cover or anything flammable in the storage space area under
the barbecue.
5. To prevent fingers, clothing or other objects from coming in contact with the auger feed system, the appliance is equipped
with a metal safety screen, mounted to the interior of the hopper. This screen must not be removed unless directed by
Customer Care or an authorized dealer.
This appliance is not recommended for children, persons with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they are under direct supervision or instruction
by a person responsible for their safety.
ENGLISH
3
6. Parts of the smoker may be very hot and serious injury may occur. Keep young children and pets away while in use.
7. Do not enlarge igniter holes or burn pots. Failure to follow this warning could lead to a fire hazard and bodily harm and will
void your warranty.
8. Product may have sharp edges or points. Contact may result in injury. Handle with care.
DISPOSAL OF ASHES
Ashes should be placed in a metal container with a tight-fitting lid. The closed container of ashes should be placed on a non-
combustible floor or on the ground, well away from all combustible materials, pending final disposal. When ashes are disposed by
burial in soil, or otherwise locally dispersed, they should be retained in a closed container until all cinders have thoroughly cooled.
WOOD PELLET FUEL
This pellet cooking appliance is designed and approved for pelletized, all natural, wood fuel only. Any other type of fuel burned in
this appliance will void the warranty and safety listing. You must only use all natural wood pellets, designed for burning in pellet
barbecue grills. Do not use fuel with additives. Wood pellets are highly susceptible to moisture and should always be stored in an
airtight container. If you are storing your grill, without use, for an extended period, we recommend clearing all pellets from your
grill's hopper and auger, to prevent jams. The pellet fuel mean heating value in 8000-8770 BTU/LB, ash content < 1%.
Do not use lava rock, wood chunks, charcoal, spirit, petrol, gasoline, lighter-fluid or kerosene for lighting or
refreshing a fire in your smoker. Keep all such substances and liquids well away from appliance when in use.
At this time of printing, there is no industry standard for barbecue wood pellets, although most pellet mills use the same standards
to make wood pellets for domestic use. Further information, can be found at
www.pelletheat.org
or the
Pellet Fuel Institute
.
Contact your local dealer on the quality of pellets in your area, and for information on brand quality. As there is no control over
the quality of pellets used with the appliance, Dansons assumes no liability caused by the quality of fuel.
CREOSOTE
Creosote, or soot, is a tar-like substance. When burning, it produces black smoke with a residue which is also black in color. Soot
or creosote is formed when the appliance is operated incorrectly, such as: blockage of the burn pot, blockage of the combustion
fan, failure to clean and maintain the burn area, or poor air-to-fuel combustion.
It is dangerous to operate this appliance should the flame become dark, sooty, or if the burn pot is overfilled with pellets. When
ignited, this creosote makes an extremely hot and uncontrolled fire, similar to a grease fire. Should this happen, turn the unit off,
let it cool completely, then inspect for maintenance and cleaning. It commonly accumulates along exhaust areas.
If creosote has formed within the unit; allow the unit to warm up at a low temperature, turn off the appliance, then wipe away
any formation with a hand towel. Similar to tar, it is much easier to clean when warm, as it becomes liquid.
CARBON MONOXIDE (“ ”)
Carbon monoxide is a colorless, odorless, tasteless gas produced by burning gas, wood, propane, charcoal or other fuel. Carbon
monoxide reduces the blood’s ability to carry oxygen. Low blood oxygen levels can result in headaches, dizziness, weakness,
nausea, vomiting, sleepiness, confusion, loss of consciousness or death. Follow these guidelines to prevent this colorless, odorless
gas from poisoning you, your family, or others:
• See a doctor if you or others develop cold or flu-like symptoms while cooking or in the vicinity of the appliance. Carbon
monoxide poisoning, which can easily be mistaken for a cold or flu, is often detected too late.
• Alcohol consumption and drug use increase the effects of carbon monoxide poisoning.
• Carbon monoxide is especially toxic to mother and child during pregnancy, infants, the elderly, smokers, and people with
blood or circulatory system problems, such as anemia, or heart disease.
ENGLISH
4
SAFETY LISTING
In accordance with the procedures and specifications listed in the 27282009 "pellet fuel cooking
appliances" and /272813 "for electrical features of fuel burning equipment." Pit Boss® Grills
pellet cooking appliances have been independently tested and listed by (an accredited testing
laboratory) to , , and standards.
ENGLISH
5
Safety Information .......................................................... 2
Parts & Specs ......................................................................6
Assembly Preparation ...................................................... 7
Operating Instructions
Smoker Environment ................................................................... 9
Smoker Temperature Ranges...................................................10
Understanding The Control Board ..........................................11
Control Board Functions ............................................................12
Hopper Priming Procedure ...................................................... 12
First Use – Smoker Burn-Off.................................................... 13
Connecting To The Smoke iT® App ..........................................13
Automatic Start-Up Procedure ................................................ 13
Manual Start-Up Procedure .................................................... 14
Shutting Off Your Smoker ........................................................ 14
Care & Maintenance ........................................................15
Using Wood Pellet Fuel ...................................................17
Cooking Guidelines ......................................................... 18
Tips & Techniques ...........................................................20
COPYRIGHT NOTICE
Copyright 2022. All right reserved. No part of this manual
may be copied, transmitted, transcribed, stored in a retrieval
system, in any form or by any means without expressed
written permission of,
Dansons
3411 North 5th Avenue, Suite 500, Phoenix, , 85013
sales@pitboss-grills.com | service@pitboss-grills.com
www.pitboss-grills.com
Customer Care
USA: (480) 923-9630
CANADA (TOLL FREE): 1-877-942-2246
Troubleshooting ..............................................................21
Electrical Wire Diagram ................................................. 23
Replacement Parts
Smoker Replacement Parts ..................................................... 24
Electrical Replacement Parts ................................................... 25
Warranty
Conditions .................................................................................... 25
Exceptions .................................................................................... 26
Ordering Replacement Parts ...................................................26
Contact Customer Care .............................................................26
Warranty Service .......................................................................26
Accessories Sold Separately .......................................... 27
Assembly Instructions ....................................................82
ENGLISH
6
71 734 1,468 709
/ 28.8 57.8 27.9
64.3
/ 141.09
0.16 / 5.6
11,715 / 1,815 . .
65215°
/ 150420°
Part# Description
1 Cooking Grids (x6)
2 Cooking Grid Support Brackets (x14)
3 Chimney Cap (x1)
4 Chimney Stack (x1)
5 Back Handle (x1)
6 Lid Stopper (x1)
7 Main Cabinet (x1)
8 Sausage Hook (x6)
9 Meat Hook (x6)
10 Cabinet Door Handle (x1)
11 Cabinet Door Latch Hook (x2)
12 Cabinet Door Latch (x2)
13 Power Cord Bracket (x1)
14 Support Bar (x1)
15 Water Pan (x1)
16 Flame Tamer (x1)
17 Grease Tray (x1)
18 Grease Tray Brackets (x2)
19 Support Panel (x2)
20 Wire Components Housing (x1)
21 Grease Exhaust Tube (x1)
22 Heat Shield (x1)
23 Meat Probe (x2)
24 Front Support Leg - Left (x1)
25 Back Support Leg - Left (x1)
26 Front Support Leg - Right (x1)
27 Back Support Leg - Right (x1)
A Door Knob (x1)
B ¼–20x½" Screw (x12)
C ¼–20x⅝" Screw (x4)
D #10–24x½" Screw (x40)
E #10–24x⅓" Screw (x2)
NOTE: Due to ongoing product development, parts are subject to change without notice. Contact
Customer Care if parts are missing when assembling the unit.
12
5
3
4
11
13
12
14
16
20 21
22
23
24
25
26
27
18
19
17
9
7
8
10
6
15
181 182
110120 , 60 z, 250 , 3
ENGLISH
7
Parts are located throughout the shipping carton, including underneath the smoker. Inspect the smoker, parts, and hardware
blister pack after removing from the protective shipping carton. Discard all packaging materials from inside and outside of the
smoker before assembly, then review and inspect all parts by referencing the parts list. If any part is missing or damaged, do not
attempt to assemble. Shipping damage is not covered under warranty. Contact your dealer or Pit Boss® Customer Care for parts.
USA: (480) 923-9630 | CANADA (TOLL FREE): 1-877-942-2246
IMPORTANT: To ease installation, using two people is helpful (but not necessary) when assembling this unit.
Tools required for assembly: screwdriver and level.
Tools not included.
82 .
IMPORTANT
- It is advised to review each step entirely before starting assembly on instructions.
-Hardware combination involving a locking washer and washer should be installed with the locking washer closest to the
head of the screw.
-Tighten screws completely after all screws for that step have been installed.
1The four support legs must be arranged correctly to be able to properly install the support panels and support bar in a
later assembly step.
2Ensure there is a good seal to the main cabinet, as grease will come from the main cabinet, flow through the exhaust tube, and
exit into the grease tray.
3If this part is not installed correctly, the heat and/or splatter from the grease exhaust tube may cause damage to the control
board. Grease damage to the rear of control board is not covered by warranty.
4Fine tune and test the cabinet door latches and hooks to ensure they align properly and there is a proper seal while the door
is closed. Poor alignment may result in heat loss and leaks during use.
5The ventilation windows on the sides of the flame tamer box must not face forward, towards the cabinet door. This may
cause damage to the control board if flames are too large.
6Keep water in the water pan at all times while cooking. It will catch grease and drippings from your cooks and allow for
easier clean up. If smoking for an extended period of time, move water pan up higher to allow water to last longer.
NOTE
1 Loosen the two screws connecting the front panel to the main cabinet.
2Using additional two screws, secure the front panel sides to the front-facing support legs. Re-tighten the previously
loosened screws.
3The support panel with two holes along the bottom should be on the same side of the unit as the power cord exits the
control board (left side). This is important for later steps.
4 The diveted end of the brackets should face the control board.
5The grease tray is completely inserted once the front of the tray is pushed in as far as it can go, with no gap between
the grease tray and the front panel.
6 To use the hopper clean-out feature, simply loosen the door knob, raise the clean-out door latch and open the door.
7Adjust the chimney cap to affect the airflow inside the main smoker. If cooking at low temperature, keep the cap more
open.
ENGLISH
8
NOTE: Before plugging your unit into any electrical outlet, ensure the temperature dial is in the OFF position.
Disconnect when not in use.
•
This unit requires 110-120 volt, 60 Hz, 250 W service. It must be a 3-prong
grounded plug. Ensure grounded end is not broken off. The control uses a
110-120 volt, fast-blow fuse to protect the board from the igniter.
•
This appliance will work on most GFCI outlets, with a recommended size
of 15 amp service. If your GFCI outlet is highly sensitive to power surges,
it will likely trip during the start-up phase of operation. During the start-
up phase, the igniter draws 200-700 watts of electricity which can be
too much power for a GFCI outlet to handle. The quality of the GFCI does
not matter, but rather the sensitivity; each time it trips, it increases in
sensitivity. If the GFCI keeps tripping, replace the outlet or change to a
non-GFCI outlet.
•
Disconnect the igniter from the main wiring harness. Use the manual
start-up procedure. A Pit Boss® unit can operate using a 12 volt, 100 watt
inverter plugged into your automobile outlet. To use the automatic igniter,
it is recommended to use a minimum of a 1000 watt inverter.
ENGLISH
9
With today’s lifestyle of striving to eat healthy and nutritious foods, a factor to consider is the importance of reducing fat intake.
One of the best ways to cut down on fat in your diet is to use a low fat method of cooking, such as smoking. As a pellet smoker
uses natural wood pellets, the savory wood flavor is cooked into the meats, reducing the need for high sugar-based sauces.
1.
With all outdoor appliances, outside weather conditions play a big part in the performance of your smoker and the cooking
time needed to perfect your meals. The Pit Boss®, because of its double wall construction, should be considered as a 3
season smoker, depending on where you live. All Pit Boss® units should keep a minimum clearance of 305mm (12 inches) from
combustible constructions, and this clearance must be maintained while the smoker is operational. This appliance must not be
placed under overhead combustible ceiling or overhang. Keep your smoker in an area clear from combustible materials, gasoline
and other flammable vapors and liquids.
2.
As it becomes cooler outside, that does not mean that the outdoor cooking season is over! The crisp cool air and heavenly
aroma of smoked foods will help cure your winter blues. Follow these suggestions on how to enjoy your smoker throughout
the cooler months:
• If smoking at low temperatures fails, increase the temperature slightly to achieve the same results.
• Organize – Get everything you require ready in the kitchen before you head outdoors. During the winter, move your
smoker to an area that is out of the wind and direct cold. Check local bylaws regarding the proximity of your smoker
in relation to your home and/or other structures. Put everything you need on a tray, bundle up tight, and get it done!
• To help keep track of the outside temperature, place an outdoor thermometer close to your cooking area. Keep a log
or history of what you cooked, the outdoor temperature, and the cooking time. This will help later down the road to
help you determine what to cook and how long it will take.
• In very cold weather, increase your preheating time by at least 20 minutes.
• Avoid opening the smoke cabinet door any more than necessary. Cold gusts of wind can completely cool your internal
temperature. Be flexible with your serving time; add about 10 – 15 minutes extra cooking time each time you open the door.
• Have a heated platter or a dish cover ready to keep your food warm while making the trip back inside.
• Ideal foods for winter cooking are those that require little attention, such as roasts, whole chickens, ribs, and turkey.
Make your meal preparation even easier by adding simple items such as vegetables and potatoes.
3.
As it becomes warmer outdoors, the cooking time will decrease. Proper dress is important when it gets really hot: shorts,
shirt, shoes, hat, apron and a generous slab of suntan lotion is recommended. Follow these few suggestions on how to enjoy
your smoker throughout the hot months:
• Adjust your cooking temperatures downward. This helps to avoid unwanted flare-ups.
• Use a meat thermometer to determine the internal temperature of your foods. This helps in preventing your meat
from over cooking and drying out.
• Even in hot weather, keep the smoke cabinet door closed at all times.
• You can keep foods hot by wrapping them in foil, and placing them in an insulated cooler. Stuff crumpled up
newspaper around the foil and this will keep food hot for 3 to 4 hours.
ENGLISH
10
Temperature readouts on the control board may not exactly match the thermometer. All temperatures listed below
are approximate and are affected by the following factors: outside ambient temperature, the amount and direction
of wind, the quality of pellet fuel being used, the cabinet door being opened, and the quantity of food being cooked.
HIGH TEMPERATURES
190-215°C / 375-420°F
This range is best used to sear and grill at a high heat. Use in tandem with the flame broiler (slide plate) for
indirect or direct flame cooking. With the
flame broiler open
, direct flame is used to create those “blue” steaks,
as well as flame-kissed vegetables, garlic toast or s’mores! When the
flame broiler is closed
, the air circulates
around the barrel, resulting in convection heat. High temperature is also used to preheat your grill, burn-off the
cooking grids, and to achieve high heat in extreme cold weather conditions.
MEDIUM TEMPERATURES
135-177°C / 275-350°F
This range is best for baking, roasting, and finishing off that slow smoked creation. Cooking at these
temperatures will greatly reduce the chances of a grease flare-up. Ensure that the flame broiler slider in the
closed position, covering the slotted openings. Great range for cooking anything wrapped in bacon, or where
you want versatility with control.
LOW TEMPERATURES
65-122°C / 150-250°F
This range is used to slow roast, increase smoky flavor, and to keep foods warm. Infuse more smoke flavor and
keep your meats juicy by cooking longer at a lower temperature (also known as
low and slow
). Recommended
for the big turkey at Thanksgiving, juicy ham at Easter, or the huge holiday feast.
Smoking is a variation on true barbecuing and is truly the main advantage of a smoker. There are two types of smoking: hot
smoking and cold smoking.
•
Hot smoking
, another name for
low and slow
cooking, is generally done at 65-122C / 150-250F. Hot smoking
works best when longer cooking time is required, such as large cuts of meats, fish, or poultry.
•
Cold smoking
is when the food is located so far away from the fire that it smokes without cooking, and at
temperatures of 15-32C / 60-90F.
TIP: To intensify that savory flavor, switch to (low) temperature range immediately after putting your food
on the smoker. This allows the smoke to penetrate the meats, before the pores of the meat close at 49°C / 120°F.
The key is to experiment with the length of time you allow for smoking, before the meal is finished cooking. Some outdoor chefs
prefer to smoke at the end of a cook, allowing the food to keep warm until ready to serve. Practice makes perfect!
ENGLISH
11
IMPORTANT: The temperature inside of any grill will vary greatly from location to location. Even
instruments calibrated together may not agree with each other.
Press the Power Button to power on the unit. This will begin the automatic startup cycle. Press and hold this
button for two seconds to Power-down the unit, activating the automatic cool-down cycle. The button will
glow blue if connected to a power source.
The Smoke iT® icon indicates a connectivity with Wi-Fi. When searching for a connection by Wi-Fi or via
Bluetooth®, the Smoke iT® icon will blink. Once a Wi-Fi connection has been established, the Smoke iT®
icon will stay solid. When connected, get live updates about the actual and COOK temperatures of the grill,
cooking time, and Meat Probe temperatures. It also allows you to adjust the settings of your Control Board.
The Controller Knob is used to increase, decrease, and select a temperature value. Rotate the Controller Knob
to change the temperature, then push the Controller Knob to confirm the chosen value. The temperature
displayed can be adjusted by 5 degree (°F) increments. The temperature can be set to a low 65°C /150°F, and
peaks at a high of 215°C /420°F.
The Temperature Switch Button is used to change the temperature readout on the LCD Screen. Press the
button to switch to Celsius (ºC) or to Fahrenheit (ºF), as preferred. Default is set to Fahrenheit.
PRIME
Press and hold this button to activate a manual, continuous feeding of pellets to the Burn Pot. Releasing the
button will stop the manual feeding of pellets. This can be used to add more fuel to the fire before opening
the barrel lid, resulting in a quick heat recovery. It can also be used while smoking, to increase the intensity
of clean smoke flavor. This feature was requested from competition cookers.
This readout displays the Actual temperature. The Actual temperature is the temperature from inside the
Main Barrel, and is constantly displayed. The Actual temperature readout is taken by the Grill Probe (sensor)
from the inside of the grill barrel.
The COOK readout displays the desired temperature that you want to achieve in the Main Barrel. To adjust
the COOK temperature, push the Controller Knob to activate, rotate the Controller Knob to change the
temperature, then push the Controller Knob to confirm the chosen value.
Displays the temperature of the connected Meat Probe(s). The displayed Meat Probe readout will
correspond with the plug-in connection port(s) selected on the front of the Control Board. When not in use,
disconnect the Meat Probe from the connection port and code "noP" will be displayed. Compatible with Pit
Boss® branded Meat Probes only. Additional Meat Probe(s) sold separately.
F/C
ENGLISH
12
•
The Grill Probe measures the internal temperature of the Main Barrel. When the COOK temperature is adjusted, the Grill
Probe will read the Actual temperature inside the Main Barrel and adjust to the desired COOK temperature.
IMPORTANT: The temperature of your unit is highly dependent on ambient outdoor weather, quality of pellets
used, flavor of pellets, and the quantity of food being cooked.
/
To adjust the desired COOK temperature of the grill, follow the steps below:
1. Push the Controller Knob. This will make the COOK temperature readout blink, to show it is active.
2. Rotate the Controller Knob to adjust to your desired temperature.
3. Once the desired temperature is reached, push the Controller Knob to confirm.
•
The meat probe measures the internal temperature of your meat in the grill, similar to your indoor oven. Plug-in the meat
probe adapter to the meat probe connection port on the Control Board and insert the stainless steel meat probe into the
thickest portion of your meat and the temperature will be displayed on the control board. To ensure the meat probe is
connected properly to the connection port, feel and hear it snap into place.
NOTE: When placing the meat probe into your meat, ensure the meat probe and meat probe wires avoid direct
contact with flame or excess heat. This can result in damage to your meat probe. Run the excess wire out the hole
located on the left side of the main grill or the top of the main grill (near the grill lid hinge). When not in use,
disconnect from the meat probe connection port and place aside to keep protected and clean.
These instructions should be followed the first time the smoker is ignited, and each time the smoker runs out of pellets in the
hopper. The auger must be primed to allow pellets to travel through the length of the auger, and fill the burn pot. If not primed,
the igniter will timeout before the pellets are ignited. Follow these steps to prime:
1. Open the hopper lid. Make sure there are no foreign objects in the hopper or blocking the auger feed system at the bottom.
2. Remove all cooking components from the interior of the smoker. Locate the burn pot in the bottom of the smoke cabinet.
3. Plug the power cord into a power source. Press the Power Button to turn the unit , and turn the Controller Knob to
the position. Check the following items:
• That you can hear the auger turning. Place your hand above the burn pot and feel for air movement. Do not place
your hand or fingers inside the burn pot. This can cause injury.
• After approximately a minute, you should smell the igniter burning and begin to feel the air getting warmer in the
burn pot. The igniter tip does not glow red hot. Do not touch the igniter. This item gets extremely hot and will burn.
4. Once verified that all electric components are working correctly, press and hold the Power Button for two seconds to
turn the unit .
5. Fill the hopper with all natural barbecue wood pellets. Monitor the pellet level using the sight-glass along the side.
6. Press the Power Button to turn the unit . Press and hold the Prime Button until you see pellets entering the burn
pot from the auger tube. Once pellets begin to drop into the burn pot, release the Prime Button. Allow the pellets to
ignite and create flame. Once flames are coming out of the burn pot, press and hold the Power Button for two seconds
to turn the control board , and let the smoker cool down.
7. After the smoker has cooled, re-install the cooking components into the main cabinet. The smoker is now ready to use.
ENGLISH
13
Once your hopper has been primed and before using your smoker for the first time with food, it is important to complete a burn-
off. Start the smoker and operate at any temperature over (177°C / 350°F) with the cabinet door closed for 30 to 40 minutes to
burn-off the unit and rid it of any foreign matter.
®
Follow these instructions on how to connect your grill to the Smoke iT® app with your Android™ or iOS® device. The app will allow
you to control and monitor your grill and meat probe temperatures from your mobile device. Enjoy the benefits that Smoke IT®
mobile connectivity has to offer!
1. Download the Smoke iT® app. Open the app and allow Bluetooth® to be enabled for setup. New users will need to create
an account and follow the prompts to login.
2. If you are within Bluetooth® range (9 m / 30 ft), the Smoke iT® app will automatically detect your grill. Select your grill
model. If you do not see your grill on the screen, ensure your unit is connected to a power source and is turned on.
3. Name your grill model (ie. My Smoker) in the app and select "Connect" at the bottom of the screen. This will save your
grill model in the devices menu.
4. From the devices menu, click the grill model to connect. This will show you the control board screen.
5. Click the settings option (gear) in the top-right corner, enter your Wi-Fi credentials, then click the check mark at the
bottom of the screen to connect. Now both Bluetooth and Wi-Fi (cloud) icons will show on the devices menu, showing
that the grill is connected.
While using the app, the screen will shine bright when the grill is active and connected. If the app screen or grill goes
dark on the devices menu, check your wireless connection or power source.
1. Plug the power cord into a grounded power source.
2. Check the burn pot to ensure there is no obstruction for proper ignition. Open the hopper lid. Ensure there are no foreign
objects in the hopper or auger feed system entry at the bottom of the cabinet. Fill the hopper with dry, all natural
barbecue hardwood pellets.
3. Press the Power Button to turn the unit on. This will activate the start-up cycle. The auger feed system will begin to
turn, the igniter will begin to glow and the fan will supply air to the burn pot. The smoker will begin to produce smoke
while the start-up cycle is taking place. The cabinet door must remain open during the start-up cycle. To confirm the
start-up cycle has begun properly, listen for a torchy roar, and notice some heat being produced.
4. Begin to preheat your smoker with the cabinet door closed. Turn the Controller Knob to 177°C / 350°F, to allow the unit
to preheat for approximately 15 to 20 minutes.
5. After preheating is complete, you are ready to enjoy your smoker at your desired temperature!
IMPORTANT: When selecting a low or the SMOKE setting after preheating, the auger will continue to turn and
feed pellets. This will momentarily raise the temperature, but temperature will eventually decrease and stabilize.
Remember, you are trying to regulate a fire, so time is necessary to achieve your desired temperature.
ENGLISH
14
IGNITER FAILURE PROCEDURE
If for any reason your electric igniter fails, check the following steps, or start your smoker using the manual
method.
1. Ensure the unit is turned off. Open the cabinet door. Remove the cooking components from inside. Remove all unburnt
pellets and ash from the burn pot. Avoid touching the igniter to avoid injury, as it may be extremely hot.
2. Once all cooking components are removed and cleaned, press the Power Button to turn the unit on. Check the
following:
• Visually confirm that the igniter is working by placing your hand above the burn pot and feeling for heat.
• Visually confirm that the igniter is protruding approximately 13mm / 0.5 inches in the burn pot.
• Visually confirm that the auger is dropping pellets into the burn pot.
• Confirm that the combustion fan is working by listening for a torchy roar.
3. If any of the above points are not working, follow
Troubleshooting
instructions
.
1. Plug the power cord into a grounded power source.
2. Check burn pot to ensure there is no obstruction for proper ignition. Open the hopper lid. Ensure there are no foreign
objects in the hopper or auger feed system. Fill hopper with dry, all natural hardwood barbecue pellets.
3. Open the cabinet door. Remove the cooking components to expose the burn pot. Place a generous handful of pellets into
the burn pot. Squirt a gelled fire starter, or other appropriate pellet starter, over the top of the pellets. A small amount
of solid fuel fire starter, such as one composed of sawdust and wax, or wood shavings, is also appropriate. Add another
small amount of pellets over the burn pot.
NOTE: Do not use spirit, petrol, gasoline, lighter-fluid or kerosene for lighting or refreshing a fire in your smoker.
4. Light the contents of the burn pot using a long match or long-nosed lighter. Allow the starter to burn for 3 to 5 minutes.
Do not attempt to add more starter into the burn pot. This can cause injury.
5. Quickly and carefully replace the cooking components to the inside of the smoke cabinet. The cabinet door must remain
open during the start-up cycle.
6. Continue start-up by following steps three through five of
Automatic Start-Up Procedure
.
1. When finished cooking, turn the temperature dial to 177°C / 350°F and close the cabinet door. Let your smoker run for 5 to
10 minutes to go through its normal cleaning method. If you have been preparing foods that are extra greasy, allow the
smoker to burn-off for an extra 10 to 20 minutes. This will reduce the chance of causing a grease fire for the next start-up.
2. Once the burn-off is complete, keep the cabinet door closed and turn the temperature dial down to 93°C / 200°F for five
minutes to allow any remaining pellets to burn out.
3. After five minutes, with the cabinet door remaining closed, press and hold the Power Button for two seconds to turn
the unit . The smoker will begin its automatic cool-down cycle. The auger system will stop feeding fuel, the flame will
burn out, and the fan will continue to run until the cool-down cycle is complete.
ENGLISH
15
Any Pit Boss® unit will give you many years of flavorful service with minimum cleaning. An important step is allowing the smoke
cabinet and cooking grids to self-clean by running the smoker at a high temperature for 5 to 10 minutes after each use. Follow
these cleaning and maintenance tips to service your smoker:
1.
• The hopper includes a clean-out feature to allow for ease of cleaning and change
out of pellet fuel flavors. To empty, locate the clean-out door of the drop chute on
the back side of the hopper. Place a clean, empty pail under the clean-out door, then
slowly turn the knob and allow the pellets to empty.
NOTE: Use a long handled brush or shop-vac to remove excess pellets,
sawdust, and debris for a complete clean-out.
• Check and clean off any debris from the fan air intake vent, found on the rear underside of the smoke cabinet. For
an extensive cleaning, carefully wipe off any grease build-up directly on the fan blades (see
Electric Wire Diagram
for access to electric components). This ensures airflow is sufficient to the feed system.
2.
• Kinks or folds in the probe wires may cause damage. A meat probe not in use should be rolled up in a large, loose coil.
• Although both probes are stainless steel, do not place in the dishwasher or submerge in water. Water damage to the
internal wires will cause a probe to short-out, causing false readings. If a probe is damaged, it should be replaced.
3.
• It is recommended to clean your burn pot after every few uses. This will ensure proper ignition and avoid any hard
build-up of debris or ash in the burn pot.
• Use a long-handled grill cleaning brush (brass or soft metal), remove any food or build-up from the cooking grids.
Best practice is to do this while they are still warm from the previous cook. Grease fires are caused by too much
fallen debris on the cooking components of the smoker. Clean the inside of your smoker on a consistent basis. In
the event you experience a grease fire, keep the smoke cabinet door closed to choke out the fire. If the fire does not
go out quickly, carefully remove the food, turn the smoker off, and shut the cabinet door until the fire is completely
out. Another way to extinguish a fire is to wrap aluminum foil around the smoke stack, closing off air to the interior.
Lightly sprinkle baking soda, if available. Check your grease tray often, and clean out as necessary. Keep in mind the
type of cooking you do. Ensure the grease exhaust tube is clear of any blockages.
IMPORTANT: The water pan may accumulate grease. Line the water pan with aluminum foil for easier clean
up after cooks. Refill and replace the water in the water pan often.
• The glass of the cabinet door is tempered and will not break with high heat; however, excessive build-up may cause
the door to not close if not cleaned regularly. Smoke and debris can be removed with frequent cleaning of the glass.
4.
• Wipe your smoker down after each use. Use warm soapy water to cut the grease. Do not use oven cleaner, abrasive
cleansers or abrasive cleaning pads on the outside smoker surfaces. All painted surfaces are not covered under
warranty, but rather are part of general maintenance and upkeep. For paint scratches, wearing, or flaking of the
finish, all painted surfaces can be touched up using high heat BBQ paint.
• Use a cover to protect your smoker for complete protection! A cover is your best protection against weather and
outside pollutants. When not in use or for longterm storage, keep the unit under a cover in a garage or shed.
ENGLISH
16
CLEANING FREQUENCY TIME TABLE (NORMAL USE)
ITEM CLEANING FREQUENCY CLEANING METHOD
Main Cabinet Glass Door Every 2-3 Smoke Sessions Mix Baking Soda & Vinegar, Scrub with Steel Wool (Fine)
Bottom of Main Cabinet Every 5-6 Smoke Sessions Scoop Out, Shop-Vac Excess Debris
Burn Pot After Each Smoke Session Scoop Out, Shop-Vac Excess Debris
Cooking Grids After Each Smoke Session Burn Off Excess, Brass Wire Brush
Water Pan After Each Smoke Session Scrub Pad & Soapy Water
Grease Tray After Each Smoke Session Scrub Pad & Soapy Water
Grease Exhaust Tube Every 5-6 Smoke Sessions Scrub Pad & Soapy Water
Auger Feed System When Pellet Bag is Empty Allow Auger to Push Out Sawdust, Leaving Hopper Empty
Electric Components Once A Year Dust Out Interior, Wipe Fan Blades with Soapy Water
Air Intake Vent Every 5-6 Smoke Sessions Dust, Scrub Pad & Soapy Water
Grill Probe Every 2-3 Smoke Sessions Scrub Pad & Soapy Water
ENGLISH
17
Clean-burning barbecue wood pellets generate about 8200 BTU’s per pound with very little ash, a low moisture content (5-7%),
and are carbon neutral. Barbecue wood pellets are produced by pure raw material (sawdust) being pulverized with a hammer-
mill, and the material is pushed through a die with pressure. As the pellet is forced through the die, it is cut, cooled, screened,
vacuumed, and then bagged for consumer use. Check with your local dealer for flavors available in your area.
NOTE: Always store wood pellets in a dry area. Any contact or exposure to moisture will result in lower heat output or
cause the pellets to swell and break apart. Use a moisture proof, resealable tub or bucket for proper storage.
ENGLISH
18
Smoking and grilling styles of cooking can give you different results based on time and temperature. For best results, keep a
record of what you cooked, at what temperature, how long you cooked for, and the results. Adjust to your taste for the next time.
Practice makes perfect. The culinary art of hot smoking refers to longer cooking times, but results in more natural wood flavor
(and a sought-after Pink Ring) on your meats. Higher temperatures result in a shorter cooking time, locking in less smoke flavor.
TIP: For best results, allow time for meats to rest after cooking. This allows the natural juices to migrate back into
the meat fiber, giving a much juicer, flavorful cut. Resting times can be as little as 3 minutes and up to 60 minutes,
depending on the size of the protein.
(Medium) (Medium/High)
Temperature Range 93-135°C / 200-275°F 135-162°C / 275-325°F 162-190°C / 325-375°F 204-215°C / 400-420°F
Size Rare - 54°C / 130°F Medium - 60°C / 140°F Well Done - 65°C / 150°F
Rib-eye Roast,
boneless
2.26 - 2.72 kg / 5 - 6 lbs. 1½ - 2 hours
Rib Roast 5.44 - 6.35 kg / 12 - 14 lbs. 2½ - 2¾ hours
Sausage
(fresh)
All sizes 4 - 5 hours
Roast
(bone-in)
All sizes 4- 5 Hours
Ribs All sizes Cook until meat pulls from the bone (approx 4 - 6 hours)
Brisket 7.25 - 3.62 kg / 16 -18 lbs. Cook until internal temperature reaches 91°C / 195°F
Size Reheat - 60°C / 140°F Medium - 66°C / 150°F Well Done - 71°C / 160°F
Ham
(cooked)
All sizes 2 - 2¾ hours
Ham
(fresh)
4.53-5.44 kg / 10-12 lbs. 7 - 8 hours
Sausage
(fresh)
All sizes 4 - 5 hours
Loin Roast 1.36-1.81 kg / 3 - 4 lbs. 1 - 2 hours 2 - 3 hours
Rib Crown Roast 1.81-2.26 kg / 4 - 5 lbs. 1½ - 2 hours 2 - 3 hours
Boston Butt
(Pork Shoulder)
3.62-4.53 kg / 8-10 lbs. 93 - 98°C / 200 - 210°F
Internal Temperature
Ribs All sizes Cook until meat pulls from the bone (approx 4 - 6 hours)
Chop
(loin, rib)
All sizes Cook until meat pulls from the bone (approx 4 - 6 hours)
Size Rare - 54°C / 130°F Medium - 60°C / 140°F Well Done - 71°C / 160°F
Roast
(fresh)
2.26 - 2.72 kg / 5 - 6 lbs. 5 -6 Hours
ENGLISH
19
Size Rare - 54°C / 130°F Medium - 60°C / 140°F Well Done - 82°C / 180°F
Turkey
(whole)
4.53-5.44 kg / 10-12 lbs. 7 - 8 Hours
Chicken
(whole)
All sizes 5 -6 Hours
Drumsticks, Breasts All sizes 4 -5 Hours
Small Game Birds All sizes 4 -5 Hours
Duck 1.36-2.26 kg / 3-5 lbs. 5 -6 Hours
Size Rare - 54°C / 130°F Medium - 60°C / 140°F Well Done - 82°C / 180°F
Whole All sizes 5 -6 Hours
Drumsticks, Breasts All sizes 4 -5 Hours
Size Rare - 54°C / 130°F Medium - 60°C / 140°F Well Done - 82°C / 180°F
Whole All sizes 2 -3 Hours, until flaky
Filets All sizes 1 -2 Hours, until flaky
Size Rare - 60°C / 140°F Medium - 71°C / 160°F Well Done - 77°C / 170°F
Roast
(fresh)
2.26 - 2.72 kg / 5 - 6 lbs. 5 -6 Hours
Large Cuts
(fresh)
3.62-4.53 kg / 8-10 lbs. 7 - 8 Hours
ENGLISH
20
Follow these helpful tips and techniques, passed on from Pit Boss® owners, our staff, and customers just like you, to become more
familiar with your smoker:
1.
• Keep everything in the kitchen and cooking area clean. Use different platters and utensils for the cooked meat than
the ones you used to prepare or transport the raw meat out to the smoker. This will prevent cross contamination of
bacteria. Each marinade or basting sauce should have its own utensil.
• Keep hot foods hot (above 60ºC / 140ºF), and keep cold foods cold (below 3ºC / 37ºF).
• A marinade should never be saved to use at a later time. If you are going to use it to serve with your meat, be sure
to bring it to a boil before serving.
• Cooked foods should not be left out in the heat for more than an hour. Do not leave hot foods out of refrigeration
for more than two hours.
• Defrost and marinade meats by refrigeration. Do not thaw meat at room temperature or on a counter top. Bacteria
can grow and multiply rapidly in warm, moist foods. Wash hands thoroughly with hot, soapy water before starting
any meal preparation and after handling fresh meat, fish and poultry.
2.
• Be prepared, or
Mise en Place
. This refers to preparing the cooking recipe, fuel, accessories, utensils, and all
ingredients you require at your side before you start cooking. Also, read the entire recipe, start to finish, before
lighting the smoker.
• A BBQ floor mat is very useful. Due to food handling accidents and cooking splatter, a BBQ floor mat would protect
a deck, patio, or stone platform from the possibility of grease stains or accidental spills.
3.
• To infuse more smoke flavor into your meats, cook longer and at lower temperatures (also known as
low and slow
).
Meat will close its fibers after it reaches an internal temperature of 49ºC / 120ºF. Misting, or mopping, are great ways
to keep meat from drying out.
• Always use a meat thermometer to determine the internal temperature of the foods you are cooking. Smoking foods
with hardwood pellets will turn meats and poultry pink. The band of pink (after cooking) is referred to as a
smoke
ring
and is highly prized by outdoor chefs.
• Sugar-based sauces are best applied near the end of cooking to prevent burning and flare-ups.
• Leave open space between the foods and the extremities of the smoke cabinet for proper heat flow. Food on a
crowded smoker will require more cooking time.
• Use a set of long-handled tongs for turning meats, and a spatula for softer items like fish and cheese. Using a
piercing utensil, such as a fork, will prick the meat and allow the juices to escape.
• Foods in deep casserole dishes will require more time to cook than a shallow baking pan.
• It’s a good idea to put cooked food onto a heated platter, keeping the food warm. Red meats, such as tenderloins
and roasts, benefit from resting for several minutes before serving. It allows the juices that were driven to the
surface by heat to ease back to the center of the meat, adding more flavor.
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
dans d''autres langues
- English: Pit Boss PBV7PW1 User manual
- español: Pit Boss PBV7PW1 Manual de usuario
