Pit Boss PB1600PS2 Manuel utilisateur

Marque: Pit Boss

Modèle: PB1600PS2

Catégorie: Mesure, test

Taper: Manuel utilisateur

ENGLISH

WARNING: PLEASE READ THE ENTIRE MANUAL BEFORE INSTALLATION AND USE OF THIS ELECTRIC, PELLET FUEL-BURNING APPLIANCE.

FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN PROPERTY DAMAGE, BODILY INJURY OR EVEN DEATH. CONTACT LOCAL

BUILDING OR FIRE OFFICIALS ABOUT RESTRICTIONS AND INSTALLATION INSPECTION REQUIREMENTS IN YOUR AREA.

AVERTISSEMENT : VEUILLEZ LIRE L’INTÉGRALITÉ DU MANUEL AVANT L’INSTALLATION ET L’UTILISATION DE CET APPAREIL ÉLECTRONIQUE

À GRANULES. LE NON-RESPECT DE CES INSTRUCTIONS PEUT ENTRAÎNER DES DOMMAGES AUX BIENS, DES BLESSURES OU MÊME LA MORT.

COMMUNIQUEZ AVEC LES AUTORITÉS LOCALES EN MATIÈRE D’INCENDIE ET DE BÂTIMENT CONCERNANT LES RESTRICTIONS ET LES

EXIGENCES D’INSTALLATION DANS VOTRE RÉGION.

ADVERTENCI: LEA EL MANUAL COMPLETO ANTES DE INSTALAR Y UTILIZAR ESTE APARATO ELÉCTRICO PARA QUEMAR PELLETS DE

COMBUSTIBLE. INCUMPLIR ESTAS INSTRUCCIONES PODRÍA CAUSAR DAÑOS MATERIALES, LESIONES CORPORALES, E INCLUSO LA MUERTE.

CONSULTE A SUS FUNCIONARIOS LOCALES DE CONSTRUCCIÓN Y CONTROL DE INCENDIOS PARA INFORMARSE SOBRE LAS RESTRICCIONES Y

LOS REQUISITOS DE INSPECCIÓN DE INSTALACIONES EN SU REGIÓN.

FOR OUTDOOR AND HOUSEHOLD USE ONLY. NOT FOR COMMERCIAL USE.

RÉSERVÉ À L'USAGE EXTÉRIEUR ET RÉSIDENTIEL UNIQUEMENT. NON DESTINÉ À UN USAGE COMMERCIAL.

SOLO PARA USO EN EXTERIORES Y EN EL HOGAR. NO ES PARA USO COMERCIAL.

ITM. / ART. 3829625

MODEL / MODÈLE / MODELO: PB1600PS2

PART / PIÈCE / PARTE: 10908

300522

  

 



  

WOOD PELLET

GRILL & SMOKER

IMPORTANT, READ CAREFULLY, RETAIN FOR FUTURE

REFERENCE. MANUAL MUST BE READ BEFORE OPERATING!

GRIL & FUMOIR À

GRANULES DE BOIS

IMPORTANT, PRENEZ CONNAISSANCE DE CE

DOCUMENT ET CONSERVEZ-LE POUR RÉFÉRENCE

ULTÉRIEURE VOUS DEVEZ LIRE CE GUIDE AVANT

D’UTILISER LE BARBECUE !

ASADOR Y AHUMADOR

DE PELLETS DE MADERA

IMPORTANTE, LEA DETENIDAMENTE, CONSERVE

PARA REFERENCIA FUTURA. ¡DEBE LEER EL

MANUAL ANTES DE LA OPERACIÓN!

ENGLISH

 

MAJOR CAUSES OF APPLIANCE FIRES ARE A RESULT OF POOR MAINTENANCE AND

A FAILURE TO MAINTAIN REQUIRED CLEARANCE TO COMBUSTIBLE MATERIALS. IT

IS OF UTMOST IMPORTANCE THAT THIS PRODUCT BE USED ONLY IN ACCORDANCE

WITH THE FOLLOWING INSTRUCTIONS.

Plese red nd understnd ths entre mnul before ttemptn to ssemble, operte or nstll the product Ths wll ensure

ou receve the most enoble nd trouble-free operton of our new wood pellet rll We lso dvse ou retn ths mnul

for future reference

DANGERS AND WARNINGS

You must contact your local home association, building or fire officials, or authority having jurisdiction,

to obtain the necessary permits, mission or information on any installation restrictions, such as any grill

being installed on a combustible surface, inspection requirements or even ability to use, in your area.

1. A minimum clearance of 914 mm (36 inches) from combustible constructions to the sides of the grill, and 914 mm (36 inches)

from the back of the grill to combustible constructions must be maintained. Do not install appliance on combustible

floors, or floors protected with combustible surfaces unless proper permits and permissions are obtained by

authorities having jurisdiction. Do not use this appliance indoors, in an enclosed or unventilated area, inside homes,

vehicles, tents, garages. This wood pellet appliance must not be placed under overhead combustible ceiling or overhang.

Keep your grill in an area clear and free from combustible materials, gasoline and other flammable vapors and liquids.

Should a grease fire occur, turn the grill OFF and leave the lid closed until the fire is out. Unplug the power

cord. Do not throw water on the unit. Do not try to smother the fire. Use of an all-class (class ABC) approved

fire extinguisher is valuable to keep on site. If an uncontrolled fire does occur, call the Fire Department.

2. Keep electrical supply cords and the fuel away from heated surfaces. Do not use your grill in the rain or around any water

source.

3. After a period of storage, or non-use, check the fire pot for obstructions, the hopper for foreign objects, and any air blockage

around the fan intake or chimney. Clean before use. Regular care and maintenance is required to prolong the lifespan of

your unit. If the grill is stored outside during the rainy season or seasons of high humidity, care should be taken to

insure that water does not get into the hopper. When wet or exposed to high humidity, wood pellets will expand greatly,

decompose, and may jam the feed system. Always disconnect the power, before performing any service or maintenance.

Do not transport your grill while in use or while the grill is hot. Ensure the fire is completely out and that

the grill is completely cool to the touch before moving.

4. It is recommended to use heat-resistant barbecue mitts or gloves when operating the grill. Do not use accessories not

specified for use with this appliance. Do not put a barbecue cover or anything flammable in the storage space area under

the barbecue.

5. To prevent fingers, clothing or other objects from coming in contact with the auger feed system, the appliance is equipped

with a metal safety screen, mounted to the interior of the hopper. This screen must not be removed unless directed by

Customer Care or an authorized dealer.

ENGLISH

This appliance is not recommended for children, persons with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless they are under direct supervision or instruction

by a person responsible for their safety.

6. Parts of the barbecue may be very hot, and serious injury may occur. Keep young children and pets away while in use.

7. Do not enlarge ignitor holes or fire pots. Failure to follow this warning could lead to a fire hazard and bodily harm and will

void your warranty.

8. Product may have sharp edges or points. Contact may result in injury. Handle with care.

DISPOSAL OF ASHES

Ashes should be placed in a metal container with a tight-fitting lid. The closed container of ashes should be placed on a non-

combustible floor or on the ground, well away from all combustible materials, pending final disposal. When ashes are disposed by

burial in soil, or otherwise locally dispersed, they should be retained in a closed container until all cinders have thoroughly cooled.

WOOD PELLET FUEL

Ths pellet coon pplnce s desned nd pproved for pelletzed, ll nturl, wood fuel onl An other tpe of fuel burned n

ths pplnce wll vod the wrrnt nd sfet lstn You must onl use ll nturl wood pellets, desned for burnn n pellet

brbecue rlls Do not use fuel wth ddtves Wood pellets re hhl susceptble to mosture nd should lws be stored n n

rtht contner If ou re storn our rll, wthout use, for n extended perod, we recommend clern ll pellets from our

rll's hopper nd uer, to prevent ms The pellet fuel men hetn vlue n 8000-8770 BTU/LB, sh content < 1%

Do not use spirit, petrol, gasoline, lighter-fluid or kerosene for lighting or refreshing a fire in your grill.

Keep all such liquids well away from the appliance when in use.

At the time of printing, there is no industry standard for barbecue wood pellets, although most pellet mills use the same standards

to make wood pellets for domestic use. Further information, can be found at

www.pelletheat.org

or the

Pellet Fuel Institute

Contact your local dealer on the quality of pellets in your area, and for information on brand quality. As there is no control over

the quality of pellets used, moisture affected pellets, we assume no responsibility to damage caused by poor quality of fuel.

CREOSOTE

Creosote, or soot, is a tar-like substance. When burning, it produces black smoke with a residue which is also black in color. Soot

or creosote is formed when the appliance is operated incorrectly, such as: blockage of the combustion fan, failure to clean and

maintain the burn area, or poor air-to-fuel combustion.

It is dangerous to operate this appliance should the flame become dark, sooty, or if the fire pot is overfilled with pellets. When

ignited, this creosote makes an extremely hot and uncontrolled fire, similar to a grease fire. Should this happen, turn the unit OFF,

let it cool completely, then inspect for maintenance and cleaning. It commonly accumulates along exhaust areas.

If creosote has formed within the unit; allow the unit to warm up at a low temperature, turn off the appliance, then wipe away

any formation with a hand towel. Similar to tar, it is much easier to clean when warm, as it becomes liquid.

CARBON MONOXIDE (“  ”)

Carbon monoxide is a colorless, odorless, tasteless gas produced by burning gas, wood, propane, charcoal or other fuel. Carbon

monoxide reduces the blood’s ability to carry oxygen. Low blood oxygen levels can result in headaches, dizziness, weakness,

nausea, vomiting, sleepiness, confusion, loss of consciousness or death. Follow these guidelines to prevent this colorless, odorless

gas from poisoning you, your family, or others:

• See a doctor if you or others develop cold or flu-like symptoms while cooking or in the vicinity of the appliance. Carbon

monoxide poisoning, which can easily be mistaken for a cold or flu, is often detected too late.

• Alcohol consumption and drug use increase the effects of carbon monoxide poisoning.

Carbon monoxide is especially toxic to mother and child during pregnancy, infants, the elderly, smokers, and people with blood

or circulatory system problems, such as anemia, or heart disease.

ENGLISH

SAFETY LISTING

In accordance with the procedures and specifications listed in the UL 2728A-2019 "pellet fuel burning cooking

appliances" and ULC/ORD C2728-19 "pellet fuel burning equipment." Pit Boss® Grills pellet cooking appliances

have been independently tested and listed by CSA (an accredited testing laboratory) to UL and ULC standards.

  

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This

equipment should be installed and operated with a minimum distance of 20cm between the radiator and

your body. This transmitter must not be co-located or operating in conjunction with any other antenna or

transmitter. This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) This device must accept any interference received,

including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

The Bluetooth® word mark and logo are registered trademarks owned by Bluetooth® SIG, Inc. and any use of such marks by

Espressif is under license. Other trademarks and tradenames are those of their respective owners.

300522

ENGLISH

  

Safety Information .......................................................... 2

Parts & Specs ......................................................................6

Assembly Preparation ...................................................... 7

Assembly Instructions

Mounting The Legs To Main Barrel .......................................... 7

Installing The Bottom Shelf ...................................................... 8

Adding Wheels To The Cart ........................................................8

Installing The Lid Handle ............................................................8

Assembling The Side Shelf .........................................................9

Mounting The Side Shelf Brackets ...........................................9

Securing The Side Shelf ...............................................................9

Securing The Front Shelf Brackets .......................................... 10

Installing The Front Shelf ......................................................... 10

Placing The Diffuser Plate ........................................................ 10

Installing The Flame Broiler Components ............................11

Installing The Cooking Components ......................................12

Mounting The Rack Hanger ......................................................12

Placing The Grease Bucket ........................................................12

Connecting To A Power Source ................................................. 13

Operating Instructions

Grill Environment ....................................................................... 14

Grill Temperature Ranges ..........................................................15

Understanding The Control Board ......................................... 16

Control Board Functions ........................................................... 18

Connecting To The Smoke iT® App ......................................... 19

Hopper Priming Procedure ..................................................... 20

First Use – Grill Burn-Off ......................................................... 20

Automatic Start-Up Procedure ............................................... 20

Shutting Off Your Grill...............................................................20

Care & Maintenance ........................................................21

Using Wood Pellet Fuel ..................................................23

Cooking Guidelines ......................................................... 23

Tips & Techniques ...........................................................25

Troubleshooting ............................................................. 26

Electrical Wire Diagram .................................................28

Replacement Parts

Grill Replacement Parts ...........................................................29

Hopper Replacement Parts ......................................................30

Warranty

Conditions ....................................................................................30

Exceptions .....................................................................................31

Ordering Replacement Parts ....................................................31

Contact Customer Care ..............................................................31

Warranty Service ........................................................................31

Recipes ..............................................................................32

Coprht 2022 All rht reserved No prt of ths mnul m be

coped, trnsmtted, trnscrbed, stored n  retrevl sstem, n n

form or b n mens wthout expressed wrtten permsson of,

Dansons

3411 North 5th Avenue, Sute 500, Phoenx, ,  85013

www.pitboss-grills.com

Customer Care

USA: (480) 942-9630

CANADA (TOLL FREE): 1-877-942-2246

ENGLISH

  

Part# Description

1 Top Cooking Rack (x1)

2 Middle Cooking Rack (x1)

3 Cooking Grid (x1)

4 Flame Broiler Adjusting Bar (x1)

5 Flame Broiler Adjusting Bar Handle (x1)

6 Flame Broiler Slider (x1)

7 Flame Broiler Main Plate (x1)

8 Rack Hanger (x1)

9 Lid Handle (x1)

10 Main Barrel / Hopper Assembly (x1)

11 Left Support Leg - Front (x1)

12 Left Support Leg - Back (x1)

13 Right Support Leg - Front (x1)

14 Right Support Leg - Back (x1)

15 Foot Gasket - A (x2)

16 Foot Gasket - B (x2)

17 Locking Caster Wheels (x4)

18 Bottom Shelf (x1)

19 Front Shelf (x1)

20 Front Shelf Bracket / Left (x1)

21 Front Shelf Bracket / Right (x1)

22 Diffuser Plate (x1)

23 Grease Bucket (x1)

24 Side Shelf Bracket / Left (x1)

25 Side Shelf Bracket / Right (x1)

26 Side Shelf (x1)

27 Meat Probe (x2)

A Screw (x38)

B Washer (x36)

C Locking Washer (x32)

D Tool Hook (x3)

E Screw (x4)

F Nut (x4)

G Bushing (x4)

NOTE: Due to ongoing product development, parts are subject to change without notice. Contact

Customer Care if parts are missing when assembling the unit.

MODEL ASSEMBLED (WxDxH) WEIGHT COOKING AREA TEMPERATURE RANGE



16002 1,590  x 757  x 1,242 

62.60 . x 29.80 . x 48.90 . 98.3  / 216.7 

   2,474.8  / 383.6 . .

  3,249.6  / 503.7 . .

  4,587.1  / 711.0 . .

  10,311.5  / 1,598.3 . .

150500° / 65260°

1 2

11 12

20 21

  

 

 

   

110120, 60z, 100, 3  

ENGLISH

 

Parts are located throughout the shipping carton, including underneath the grill. Inspect the grill, parts, and hardware blister

pack after removing from the protective shipping carton. Discard all packaging materials from inside and outside of the grill

before assembly, then review and inspect all parts by referencing the parts list. If any part is missing or damaged, do not attempt

to assemble. Shipping damage is not covered under warranty. Contact your dealer or Pit Boss® Customer Care for parts.

www.pitboss-grills.com | USA: (480) 942-9630 | CANADA (TOLL FREE): 1-877-942-2246

IMPORTANT: To ease installation, using two people is helpful (but not necessary) when assembling this unit.

Tools required for assembly: screwdriver and level.

Tools not included.

 

IMPORTANT: It is advised to read each step entirely before starting assembly on instructions. Do not tighten screws

completely until all screws for that step have been installed. Hardware combination involving a locking washer and

washer should be installed with the locking washer closest to the head of the screw.

1.       

Parts Required:

1 x Main Barrel /Hopper Assembly (#10)

1 x Left Support Leg - Front (#11)

1 x Left Support Leg - Back (#12)

1 x Right Support Leg / Front (#13)

1 x Right Support Leg / Back (#14)

12 x Screw (#A)

12 x Locking Washer (#C)

12 x Washer (#B)

Installation:

• Place a piece of cardboard on the floor to prevent scratching the unit and

parts during assembly. Lay the Main Barrel on its side on the cardboard,

hopper end pointed upward.

• Mount the Front-Right Support Leg to the floor end of the Main Barrel

using three screws, locking washers, and washers, through the three pre-

drilled holes. Install screws from the inside of the Main Barrel. Repeat

installation for Back-Right Support Leg. Note illustration 1A.

• Next, mount the Front-Left Support Leg to the hopper end of the Main

Barrel using three screws, locking washers, and washers, through the

three pre-drilled holes. Install screws from the inside of the Main Barrel.

Repeat installation for Back-Left Support Leg. Note illustration 1B.

IMPORTANT: Do not tighten screws completely until bottom shelf is

installed in next step.

1

1



ENGLISH

2.    

Parts Required:

1 x Bottom Shelf (#18)

4 x Screw (#A)

4 x Locking Washer (#C)

4 x Washer (#B)

Installation:

• Mount the Bottom Shelf to each Support Leg using a screw, locking

washer, and washer. Ensure the flat surface of the shelf is facing up

towards the Grill Barrel.

3.     

Parts Required:

2 x Foot Gasket - A (#15)

2 x Foot Gasket - B (#16)

4 x Locking Caster Wheels (#17)

12 x Screw (#A)

12 x Locking Washer (#C)

12 x Washer (#B)

Installation:

• Place Foot Gasket between the Support Leg and Locking Caster Wheel.

Hand-tightening three screws, locking washers, and washers into the

holes on each Support Leg. Ensure that each Locking Caster Wheel is

inserted completely. Note illustration.

• Once the shelf is secure, carefully lift the grill into an upright position.

IMPORTANT: Re-tighten the support leg screws to ensure they are

completely secure after positioning the grill upright.

4.    

Parts Required:

1 x Lid Handle (#9)

Installation:

• Remove the pre-installed screws from the Lid Handle. From inside the

barrel lid, insert one screw to protrude to the outside, then hand tighten

the screw (from the inside) into the Lid Handle.

• Repeat the same installation for the other end of Lid Handle.



















ENGLISH

5.    

Parts Required:

1 x Side Shelf (#26)

3 x Tool Hook (#)

Installation:

• Turn the Side Shelf upside down. On the edge of the Side Shelf with

three holes, install the tool hooks into each hole along the edge. The

tool hooks will secure to the nut that is pre-mounted on the inside.

6.     

Parts Required:

1 x Side Shelf Bracket / Left (#24)

1 x Side Shelf Bracket / Right (#25)

4 x Screw (#A)

4 x Locking Washer (#C)

4 x Washer (#B)

Installation:

• Hand-tighten a Side Shelf Bracket with two screws, locking washers,

and washers to the right facing side of the Main Barrel.

• Repeat for the other Side Shelf Bracket.

NOTE: Do not tighten screws completely until all screws have been

installed. Once all screws are installed, then tighten securely.

7.    

Parts Required:

1 x Side Shelf (#26)

2 x Nut (#F)

2 x Washer (#B)

2 x Bushing (#G)

2 x Screw (#E)

Installation:

• Place Side Shelf onto the Side Shelf Brackets and from underneath

secure each side with a nut, washer, bushing, and screw. The screw

should be on the inside edge of the Support Bracket.

• Repeat for the other side.

IMPORTANT: Avoid using the shelves to move or lift the grill. The

weight of the unit will cause the shelves to break, which is not

covered by warranty.

526



    













ENGLISH

8.     

Parts Required:

1 x Front Shelf Bracket / Left (#20)

1 x Front Shelf Bracket / Right (#21)

6 x Screw (#A)

Installation:

• Attach one Front Shelf Bracket to the front of the grill barrel by using

three screws. Install each screw halfway, then tighten completely

when all three screws are mounted and aligned properly.

• Repeat the same installation for the other Front Shelf Bracket.

9.    

Parts Required:

1 x Front Shelf (#19)

2 x Screw (#E)

2 x Bushing (#G)

2 x Washer (#B)

2 x Nut (#F)

Installation:

• From underneath, insert the screw (from the outside) into the Front

Shelf Bracket and the Front Shelf, then add the bushing onto the

screw, the washer, then the nut.

• Repeat installation for the other side of the Front Shelf.

NOTE: When installed correctly, the Front Shelf can be raised (for

use)and lowered (for storage) with ease.

IMPORTANT: Avoid using the shelves to move or lift the grill. The

weight of the unit will cause the shelves to break, which is not

covered by warranty.

10.    

Parts Required:

1 x Diffuser Plate (#22)

Installation:

• Place the Diffuser plate into Main Barrel so the central opening aligns

directly with the circular fire pot on the base of the Main Barrel.

NOTE: The Diffuser Plate does not require fastening.









ENGLISH

11.     

Parts Required:

1 x Flame Broiler Slider (#6)

1 x Flame Broiler Main Plate (#7)

1 x Flame Broiler Adjusting Bar Handle (#5)

1 x Flame Broiler Adjusting Bar (#4)

Installation:

• Insert the Flame Broiler Main Plate into the Main Grill, right side first.

Rest the Flame Broiler Main Plate on the built-in ledge (on the inside

right) of the Main Grill that directs grease towards the grease bucket.

Slide the entire piece to the left side, and the two slots on the Flame

Broiler Main Plate will fit into the rounded ledge above the fire pot. It

will sit slightly at a downward angle. Note 11.

IMPORTANT: If the Flame Broiler Main Plate is on the base of the

barrel, it is installed incorrectly. The Flame Broiler Main Plate should

sit at an angle, with the left side sitting higher than the right. Poor

installation of this part may result in damage to your Main Grill

barrel.

• Place the Flame Broiler Slider on top of the Flame Broiler Main Plate,

covering the slotted openings. Ensure the raised tab is on the left,

to easily adjust for direct or indirect flame when cooking. Note

illustration 11. Both Flame Broiler parts are lightly coated with oil to

avoid rusting when shipped.

• Next, remove the Flame Broiler Adjusting Bar Handle from the Flame

Broiler Adjusting Bar. Insert the Flame Broiler Adjusting Bar through

the opening hole on the left side of the Main Barrel. Add the Flame

Broiler Adjusting Bar Handle back onto the end outside the barrel.

Next, slide the notched end of the Adjusting Bar into the locking tab

on the Flame Broiler Slider, giving you adjustable access to the Flame

Broiler Slider on the main plate. Note steps in 11C.

NOTE: When the Flame Broiler Slider is open and direct flame is used,

do not leave the grill unattended for any period of time.

11

11

11

Insert the flame broiler adjusting bar

through the opening hole on the left

side of the main barrel. Add the flame

broiler adjusting bar handle on the end

outside the barrel. Next, slide the

notched end of the adjusting bar into

the locking tab on the flame broiler

slider, giving you adjustable access to

the flame broiler slider on the main

plate.

Insert the flame broiler adjusting bar

through the opening hole on the left

side of the main barrel. Add the flame

broiler adjusting bar handle on the end

outside the barrel. Next, slide the

notched end of the adjusting bar into

the locking tab on the flame broiler

slider, giving you adjustable access to

the flame broiler slider on the main

plate.



ENGLISH

12.    

Parts Required:

1 x Top Cooking Rack (#1)

1 x Middle Cooking Rack (#2)

1 x Cooking Grid (#3)

Installation:

• Place the Cooking Grid on the lower ledges inside of the Main Barrel.

Next, place the Middle Cooking Rack on the middle ledges inside the

Main Barrel. Lastly, place the Top Cooking Rack on the top ledges inside

of the Main Barrel.

NOTE: To maintain the searing and grilling performance of your

Cooking Grids, regular care and maintenance is required.

13.    

Parts Required:

1 x Rack Hanger (#8)

Installation:

• Secure the Rack Hanger to the back panel of the Main Barrel using

the pre-assembly two screws. Cooking Racks can be hung on the Rack

Hanger while not in use.

14.    

Parts Required:

1 x Grease Bucket (#23)

Installation:

• Place the Grease bucket on the spout hook on the end of the Main

Barrel. Ensure it is level to avoid grease spills.

• The unit is now completely assembled.

ENGLISH

15.     

•  

This appliance requires 110-120 volt, 60Hz, 100w. It must be a 3-prong

grounded plug. Ensure grounded end is not broken off before use. The

control uses a 110-120 volt, fast-blow fuse to protect the board from

the ignitor.

•  

This appliance will work on most GFCI outlets, with a recommended

size of 15 amp service. If your GFCI outlet is highly sensitive to power

surges, it will likely trip during the start-up phase of operation. During

the start-up phase, the ignitor draws 200-700 watts of electricity

which can be too much power for a GFCI outlet to handle. Each time it

trips, it increases in sensitivity. If the GFCI keeps tripping, replace the

outlet or change to a non-GFCI outlet.

•   

Disconnect the ignitor from the main wiring harness. Use the manual

start-up procedure. A Pit Boss® unit can operate using a 12 volt,

100 watt inverter plugged into your automobile outlet. To use the

automatic ignitor, it is recommended to use a minimum of a 1000 watt

inverter.

IMPORTANT: Disconnect unit from power source when not in use.

ENGLISH

 

With today’s lifestyle of striving to eat healthy and nutritious foods, one factor to consider is the importance of reducing fat

intake. One of the best ways to cut down on fat in your diet is to use a low fat method of cooking, such as grilling. As a pellet

grill uses natural wood pellets, the savory wood flavor is cooked into the meats, reducing the need for high sugar content sauces.

Throughout this manual, you will notice the emphasis on grilling food slowly at LOW or MEDIUM temperature settings.

 

    

With all outdoor appliances, outside weather conditions play a big part in the performance of your grill and the cooking time

needed to perfect your meals.

All Pit Boss® units should keep a minimum clearance of 914 mm (36 inches) from combustible constructions, and this clearance

must be maintained while the grill is operational. This appliance must not be placed under overhead combustible ceiling or

overhang. Keep your grill in an area clear from combustible materials, gasoline and other flammable vapors and liquids.

  

As it becomes cooler outside, that does not mean that grilling season is over! The crisp cool air and heavenly aroma of

smoked foods will help cure your winter blues.

Follow these suggestions on how to enjoy your grill throughout the cooler months:

• If smoking at low temperatures fails, increase the temperature slightly to achieve the same results.

• Organize – Get everything you require ready in the kitchen before you head outdoors. During the winter, move your

grill to an area that is out of the wind and direct cold. Check local bylaws regarding the proximity of your grill in

relation to your home and/or other structures. Put everything you need on a tray, bundle up tight, and get it done!

• To help keep track of the outside temperature, place an outdoor thermometer close to your cooking area. Keep a log

or history of what you cooked, the outdoor temperature, and the cooking time. This will help later down the road to

help you determine what to cook and how long it will take.

• In very cold weather, increase your preheating time by at least 20 minutes.

• Avoid lifting the lid any more than necessary. Cold gusts of wind can completely cool your grill temperature. Be

flexible with your serving time; add extra cooking time each time you open the lid.

• Have a heated platter or a dish cover ready to keep your food warm while making the trip back inside.

• Ideal foods for winter cooking are those that require little attention, such as roasts, whole chickens, ribs, and turkey.

Make your meal preparation even easier by adding simple items such as vegetables and potatoes.

  

As it becomes warmer outdoors, the cooking time will decrease.

Follow these few suggestions on how to enjoy your grill throughout the hot months:

• Adjust your cooking temperatures downward. This helps to avoid unwanted flare-ups.

• Use a meat thermometer to determine the internal temperature of your foods. This helps in preventing your meat

from over cooking and drying out.

• Even in hot weather it is still better to cook with the lid of your grill down.

• You can keep foods hot by wrapping them in foil, and placing them in an insulated cooler. Stuff crumpled up

newspaper around the foil and this will keep food hot for 3 to 4 hours.

ENGLISH

  

Temperature readouts on the control board may not exactly match the thermometer. All temperatures listed below

are approximate and are affected by the following factors: outside ambient temperature, the amount and direction of

wind, the quality of pellet fuel being used, the lid being opened, and the quantity of food being cooked.

Smoking is a variation on true barbecuing and is truly the main advantage of grilling on a wood pellet grill.

Hot smoking

another name for

low and slow

cooking, is generally done between 65-125C / 150-257F. Hot smoking works best when

longer cooking time is required, such as large cuts of meats, fish, or poultry.

TIP: To intensify that savory flavor, switch to a low temperature range immediately after putting your food on the

grill. This allows the smoke to penetrate the meats.

The key is to experiment with the length of time you allow for smoking, before the meal is finished cooking. Some outdoor chefs

prefer to smoke at the end of a cook, allowing the food to keep warm until ready to serve. Practice makes perfect!

HIGH TEMPERATURES

205-260°C / 401-500°F

This range is best used to sear and grill at a high heat. Use in tandem with the flame broiler (slide plate) for

indirect or direct flame cooking. With the

flame broiler open

, direct flame is used to create those “blue” steaks,

as well as flame-kissed vegetables, garlic toast or s’mores! When the

flame broiler is closed

, the air circulates

around the barrel, resulting in convection heat. High temperature is also used to preheat your grill, burn-off the

cooking grids, and to achieve high heat in extreme cold weather conditions.

MEDIUM TEMPERATURES

135-180°C / 275-356°F

This range is best for baking, roasting, and finishing off that slow smoked creation. Cooking at these

temperatures will greatly reduce the chances of a grease flare-up. Ensure that the flame broiler slider in the

closed position, covering the slotted openings. Great range for cooking anything wrapped in bacon, or where

you want versatility with control.

LOW TEMPERATURES

65-125°C / 150-257°F

This range is used to slow roast, increase smoky flavor, and to keep foods warm. Infuse more smoke flavor and

keep your meats juicy by cooking longer at a lower temperature (also known as

low and slow

). Recommended

for the big turkey at Thanksgiving, juicy ham at Easter, or the huge holiday feast.

ENGLISH

   

This P.I.D. (proportional-integral-derivative) digital Control Board is very much the same as the controls on your kitchen oven. The

main advantages are the ability to automatically compensate for the different ambient conditions and fuel types.

IMPORTANT: The temperature inside of any grill will vary greatly from location to location. Even instruments

calibrated together may not agree with each other.

 

The button will light up solid white when connected to a power source and when the unit is on. Press

this button once to Power On the unit. This will begin the automatic start-up cycle. Press and hold this

button for three seconds to Power-down the unit, activating the automatic cool-down cycle.**

**This readout is displayed after Power-down has been selected. It indicates that the automatic cool-

down cycle has started. Once the cool-down cycle is completed, the readout will no longer be visible.

Press this button to on the light, press again to turn off the light.

The Smoke iT® icon indicates a connectivity with Wi-Fi. When searching for a connection by Wi-Fi or

via Bluetooth®, the Smoke iT® icon will blink. Once a Wi-Fi connection has been established, the Smoke

iT® icon will stay solid. When connected, get live updates about the actual and set temperatures of

the grill, cooking time, and meat probe temperatures. It also allows you to adjust the settings of your

Control Board.

Press the button once to activate the Recipe Steps. There are nine Recipe Steps available to set. Adjust

the settings of each Recipe Step by using the Controller Knob. Press the button again to return to menu

operation mode.

This button has two functions: Meat Probe Control (MPC) and Prime Button.

1. The quick push of this button activates the Programmable Meat Probe - which is the first Meat Probe

plug-in port (MPC). Use the Controller Knob to set the Programmable Meat Probe temperature.

Press the Controller Knob again to confirm and exit the Programmable Meat Probe settings.

2. Press and hold this button for three seconds to activate a manual continuous feeding of pellets to

the fire pot. Releasing the button will stop the manual feeding of pellets. This can be used to add

more fuel to the fire before opening the barrel lid, resulting in a quick heat recovery. It can also be

used while smoking, to increase the intensity of clean smoke flavor. This feature was requested

from competition cookers.

ENGLISH

The Controller Knob increases, decreases, and selects a setting value. Rotate the Controller Knob to set

the time, temperature, or recipe step. Push the Controller Knob to confirm the chosen value.

The central readout displays both the Actual and Set temperatures. The Actual temperature is constantly

displayed unless the Set temperature is being adjusted. The Actual temperature is the temperature

from inside the Main Barrel. The Actual temperature readout is taken by the grill probe (sensor) from

the inside of the grill barrel.

To show the Set temperature, press the Controller Knob. The Set temperature is active when the readout

is blinking. To adjust the Set temperature, rotate the Controller Knob, as needed. Once the desired Set

temperature is reached, press the Controller Knob to confirm the Set temperature, then the readout will

return back to the Actual Temperature.

Press SMOKE MODE button, it will blink to indicate you are in Smoke Mode. You can set "P" Set while

in smoke mode, the temperature must be set at 150°F minimum. For the best flavor set your smoke

temperature under 250°F. Press SMOKE MODE to cancel.

Press "P" Set button it will flash to display the P value. The knob can be used to adjust P0-P7. Press and

hold to switch the temperature unit between °F/°C.

Displays the current Recipe Step. Use the Controller Knob to switch through the Recipe Steps.

Displays the Time set during the Recipe Step. Press the Recipe Button to activate the Recipe settings.

Use the Controller Knob to set the Time for each recipe step, you can set the hours and minutes.

Displays the Actual and Set temperature of the Programmable Meat Probe - which is the first Meat

Probe plug-in port (MPC). The Actual temperature is constantly displayed unless the Set temperature is

being adjusted. When the MPC Button is pressed, the selected Meat Probe readout will blink and the Set

temperature can be adjusted. When a Meat Probe is disconnected from the connection port the code

"noP" will be displayed. Compatible with Pit Boss® Grills branded meat probes only. The temperature

ranges are 50-250°F, with 5°F increments.

Displays the Actual temperature of a Meat Probe. The (MP1, 2, 3) Meat Probe readouts correspond

with the plug-in connection port selected. When a Meat Probe is disconnected from the connection

port the code "noP" will be displayed. Compatible with Pit Boss® Grills branded meat probes only. The

temperature ranges are 50-250°F, with 5°F increments.

The FAN icon is visible when the fan is in operation. When the central readout has an error code (Err)

and the FAN icon is blinking, the Fan is not working. See the section on troubleshooting for assistance.

The AUGER icon is visible when the auger is turning. When the central readout has an error code (Err) and

the AUGER icon is blinking, the auger is not working. See the section on troubleshooting for assistance.

The IGNITOR icon is visible when the ignitor is in use. When the central readout has an error code (Err)

and the IGNITOR icon is blinking, the ignitor is not working. See the section on troubleshooting for

assistance.

When the central readout has an error code (Err) and the PELLET icon is visible, the fire in the fire pot has

gone out or the hopper may be empty. See the section on troubleshooting for assistance.

ENGLISH

  "" 

When the "P" SET button is pushed, the “P” setting displayed on the LCD screen will

flash and change to the next value (upward). You must set to a minimum temperature

of 150°F or "S". Once P7 is reached, it will restart at P0. There are eight “P” settings,

ranging from P0 to P7.

•

  "" 

Anytime the temperature dial is set to SMOKE, such as the start-up cycle, the

auger will run more off a manual cooking mode versus one of the preset dial

temperatures. First, the auger will continuously turn and feed pellets for four

minutes. After four minutes, the auger begins to run a feed cycle based on the

"P' setting selected on the Digital Control Board. The default setting is P4.

  

•

   

The Grill Probe measures the internal temperature of the Main Barrel. When the Set temperature is adjusted, the Grill Probe

will read the Actual temperature inside the Main Barrel and adjust to the desired Set temperature.

IMPORTANT: The temperature of your unit is highly dependent on ambient outdoor weather, quality of pellets

used, flavor of pellets, and the quantity of food being cooked.

/   

To adjust the desired Set temperature of the grill, follow the steps below:

1. Press the Controller Knob. This will make the Set temperature readout blink, to show it is active.

2. Use the Controller Knob again to adjust to your desired temperature.

3. Once the desired Set temperature is reached, press the Controller Knob to confirm the Set temperature,

then the readout will return back to the Actual Temperature.

•

    

The meat probe measures the internal temperature of the meat on the grill, similar to your indoor oven. Insert the stainless-

steel meat probe into the thickest portion of the meat. The internal temperature of the meat is shown on the Control

Board readout. Plug-in the Meat Probe adapter to the meat probe connection port and ensure it is inserted all the way

into the plug. You will feel and hear it snap in place. Not only will it cook the meat to your desired temperature, but it will

automatically reduce your grill temperature to low (65°C / 150°F) to keep food warm until ready to serve. Just set it, then

relax while the Meat Probe does the rest!

NOTE: When placing the meat probe into your meat, ensure the meat probe and meat probe wires avoid direct

contact with flame or excess heat. This can result in damage to your meat probe. Run the excess wire out the rear

exhaust holes of the Main Barrel, the top of the Main Barrel (near the grill lid hinge), or through the front hole

near the hopper. When not in use, disconnect from the meat probe connection port, and place in the holes on the

hopper handle to keep protected and clean.

/    

  (seconds)

""   

0 18 55

1 18 70

2 18 85

3 18 100

*4 18 115

5 18 130

6 18 140

7 18 150

default setting

ENGLISH

To program the desired Set temperature of the Programmable Meat Probe, follow the steps below:

1. Quick press the MPC button to activate the Programmable Meat Probe. When active, the temperature

readout of the Meat Probe will blink.

2. Use the Controller Knob to adjust to the desired Set temperature.

3. Once the desired Set temperature of your selected Meat Probe is reached, press the Controller Knob

again to confirm and exit the Programmable Meat Probe settings.

•

   

The Recipe function allows the user to program cooking instructions, known as Recipe Steps, for the Control Board to follow

and automatically run. These cooking instructions are a combination between Cooking temperature and Time. Starting from

the first Recipe Steps (01), the Control Board will cycle through each Recipe Steps to cook the meal. When all the Recipe Steps

are complete, the Control Board will automatically switch to a low temperature of 65°C / 150°F so that the meal stays warm

until ready to serve. There are a total of nine Recipe Steps available to be programmed.

     

To set one or more of the Recipe Steps, follow the steps below:

1. Press and hold the Recipe Button. This will make the Recipe Button blink to show the Recipe settings are

active. This will also activate the Recipe Steps and the letter 'S' will be on to show it is active.

• Use the Controller Knob to select the Recipe Step. Start with the first Recipe Step (01).

• When desired Recipe Step is reached, press the Controller Knob to go to next setting.

2. Set the Time hours. The hours of the Time readout will blink, to show it is selected.

• Use the Controller Knob to select the hours desired.

• When desired hours are reached, press the Controller Knob to go to next setting.

3. Set the Time minutes. The minutes of the Time readout will blink, to show it is selected.

• Use the Controller Knob to select the minutes desired.

• When desired minutes are reached, press the Controller Knob to go to next setting.

4. Set the Temperature. The central temperature readout will blink, to show it is selected.

• Use the Controller Knob to select the desired temperature.

• When desired temperature is reached, press and hold the Recipe Button to lock in all Recipe settings

for that Recipe Step.

• To set another Recipe Step, quick press the Recipe Button to select another Recipe Step,

programming a multiple Recipe Step cook. Repeat steps above, as desired.

Or,

• Press and hold the Recipe Button a second time to exit the Recipe settings and run the Recipe.

The Recipe Button will stop blinking.

NOTE: The Recipe Steps will reset when the unit is shut-down / turned off.

    ® 

ENGLISH

Follow these instructions on how to connect your grill to the Smoke iT® app with your Android™ or iOS® device. The app will allow

you to control and monitor your grill and meat probe temperatures from your mobile device. Enjoy the benefits that Smoke IT®

mobile connectivity has to offer!

1. Download the Smoke iT® app. Open the app and allow Bluetooth® to be enabled for setup. New users will need to create

an account and follow the prompts to login.

2. If you are within Bluetooth® range (9 m / 30 ft), the Smoke iT® app will automatically detect your grill. Select your grill

model. If you do not see your grill on the screen, ensure your unit is connected to a power source and is turned on.

3. Name your grill model (ie. My Smoker) in the app and select "Connect" at the bottom of the screen. This will save your

grill model in the devices menu.

4. From the devices menu, click the grill model to connect. This will show you the control board screen.

5. Click the settings option (gear) in the top-right corner, enter your Wi-Fi credentials, then click the check mark at the

bottom of the screen to connect. Now both Bluetooth® and Wi-Fi (cloud) icons will show on the devices menu, showing

that the grill is connected.

While using the app, the screen will shine bright when the grill is active and connected. If the app screen or grill goes

dark on the devices menu, check your wireless connection or power source.

  

These instructions should be followed the first time the grill is ignited, and each time the grill runs out of pellets in the hopper.

The auger must be primed to allow pellets to travel through the length of the auger, and fill the feed system. If not primed, the

ignitor will timeout before the pellets are ignited, and no fire will start. Follow these steps to prime the hopper:

1. Open the Main Barrel lid. Remove all cooking components from the interior of the grill. Locate the fire pot in the bottom

of the Main Barrel. Check the fire pot to ensure there is no obstruction for proper ignition.

2. Plug the power cord into a power source. Press the Power button to Power On the unit. Check the following items:

• That you can hear the auger turning. Place your hand above the fire pot and feel for air movement. Do not place your

hand or fingers inside the fire pot. This can cause injury.

• After approximately five minutes you should begin to feel the air getting warmer in the fire pot. The ignitor tip does

not glow red, but gets extremely hot and will burn. Do not touch the ignitor.

3. Once verified that all electric components are working correctly, press and hold the Power Button for 3 seconds to turn

the unit off.

4. Open the hopper lid. Ensure there are no foreign objects in the hopper or auger feed system. Fill the hopper with dry, all

natural barbecue hardwood pellets.

5. Press the Power Button to turn the unit on again. The grill start-up cycle has a preset temperature of 176°C / 350°F, so it

will begin to heat up. Press and hold the Prime Button until you see pellets on the inside of the grill from the auger tube.

Once pellets begin to drop into the fire pot, release the Prime Button.

6. Press and hold the Power Button for 3 seconds to turn the unit off.

7. Re-install the cooking components into the Main Barrel. The grill is now ready to use.

    

Once your hopper has been primed and before cooking on your grill for the first time, it is important to complete a grill burn-off.

Start the grill and operate at any temperature over 176°C / 350°F (with the lid down) for 30 to 40 minutes to burn-off the grill

and rid it of any foreign matter.

La page charge ...

Pit Boss PB1600PS2 Manuel utilisateur

Marque: Pit Boss

Modèle: PB1600PS2

Catégorie: Mesure, test

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Pit Boss PB1600PS2 User manual
español: Pit Boss PB1600PS2 Manual de usuario

Pit Boss PB1600PS2 Manuel utilisateur

Pit Boss PB1600PS2 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents