LG STUDIO LSCG307ST Guide d'installation

Marque: LG STUDIO

Modèle: LSCG307ST

Taper: Guide d'installation

Ce manuel convient également à

INSTALLATION MANUAL

GAS COOKTOP

Read this owner's manual thoroughly before operating the

appliance and keep it handy for reference at all times.

ENGLISH

MFL71938001

Rev.00_051222

www.lg.com

us_main.book.book Page 1 Thursday, May 12, 2022 9:01 AM

Safety for a Gas Cooktop

WARNING: If the information in these instructions is not

followed exactly, a fire or explosion may result causing property damage,

personal injury or death.

•Do not store or use gasoline or other flammable vapors and liquids in

the vicinity of this or any other appliance.

•WHAT TO DO IF YOU SMELL GAS

-Do not try to light any appliance.

-Do not touch any electrical switch.

-Do not use any phone in your building.

-Immediately call your gas supplier from a neighbor's phone. Follow

the gas supplier's instructions.

-If you cannot reach your gas supplier, call the fire department.

•Installation and service must be performed by a qualified installer,

service agency, or the gas supplier.

WARNING:

Never Operate the Top Surface Cooking Section of this Appliance

Unattended.

•Failure to follow this warning statement could result in fire,

explosion, or burn hazard that could cause property damage,

personal injury, or death.

•If a fire should occur, keep away from the appliance and

immediately call your fire department.

DO NOT ATTEMPT TO EXTINGUISH AN OIL/GREASE FIRE WITH

WATER.

us_main.book.book Page 6 Tuesday, May 3, 2022 10:34 AM

TABLE OF CONTENTS

4 IMPORTANT SAFETY

INSTRUCTIONS

4 READ ALL INSTRUCTIONS BEFORE USE

4WARNING

6 INSTALLATION

6 Before Installing

8 Installing the Cooktop

13 APPENDIX

13 Checking Operation

us_main.book.book Page 3 Thursday, May 12, 2022 9:01 AM

4IMPORTANT SAFETY INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USE

Download this owner's manual at http://www.lg.com

Safety Messages

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and

follow all safety messages.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury,

and tell you what may happen if the instructions are not followed.

WARNING

• To reduce the risk of explosion, fire, death, electric shock, injury or scalding to persons when using this

product, follow basic precautions, including the following:

Installation

• Remove all tape and packing materials before using the cooktop. Dispose of all plastic bags after

unpacking the cooktop. Never allow children to play with packing materials.

• Never reuse old flexible connectors. The use of old flexible connectors can cause gas leaks and personal

injury. Always use NEW flexible connectors when installing a gas appliance.

• Remove all packing material and literature before connecting gas and electrical supply.

• Have your cooktop installed by a qualified installer.

• Your cooktop must be electrically grounded in accordance with local codes or, in the absence of local

codes, in accordance with the National Electrical Code (ANSI/NFPA 70, latest edition). In Canada,

electrical grounding must be in accordance with the current CSA C22.1 Canadian Electrical Code Part 1

and/or local codes. Refer to step 3, Electrical Connections, in this manual.

• Be sure the wall coverings around the cooktop can withstand heat generated by the cooktop up to 200

℉.

• The ventilating hood must be constructed of sheet metal not less than 0.0122″ thick. Install above the

cooktop with a clearance of not less than 1/4″ between the hood and the underside of the combustible

material or metal cabinet. The hood must be at least as wide as the appliance and centered over the

appliance. Clearance between the cooking surface and the ventilation hood surface MUST NEVER BE

LESS THAN 24 INCHES.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or injure you and others. All safety messages

will follow the safety alert symbol and either the word WARNING or CAUTION.

These words mean:

WARNING

You may be killed or seriously injured if you do not follow instructions.

CAUTION

You may be injured or cause damage to the product if you do not follow instructions.

us_main.book.book Page 4 Thursday, May 12, 2022 9:01 AM

5IMPORTANT SAFETY INSTRUCTIONS

ENGLISH

SAVE THESE INSTRUCTIONS

EXCEPTION: Installation of a listed microwave oven or cooking appliance over the cooktop shall conform

to the installation instructions packed with that appliance.

• If cabinets are located above the cooktop, allow a minimum clearance of 30″ between the cooking

surface and the bottom of unprotected cabinets.

•If a 30″ clearance between cooking surface and overhead combustible material or metal cabinets cannot

be maintained, protect the underside of the cabinets above the cooktop with not less than 1/4″

insulating millboard covered with sheet metal not less than 0.0122″ thick. Clearance between the

cooking surface and protected cabinets MUST NEVER BE LESS THAN 24 INCHES.

• The vertical distance from the plane of the cooking surface to the bottom of adjacent overhead cabinets

extending closer than 1″ to the plane of the cooktop sides must not be less than 18″. (See the

Dimensions and Clearances illustration in this manual.)

• Do not obstruct the combustion or ventilation air vents.

• Leak testing of the appliance must be conducted according to the manufacturer’s instructions.

• Items of interest to children should not be placed in cabinets above the cooktop.

- Children climbing on the cooktop to reach items could be seriously injured.

• This appliance must not be installed with a ventilation system that blows air downward toward the

cooktop. This type of ventilation system may cause ignition and combustion problems with the gas

cooking appliance resulting in personal injury or unintended operation.

us_main.book.book Page 5 Thursday, May 12, 2022 9:01 AM

6INSTALLATION

INSTALLATION

Before Installing

Before You Begin

Read these instructions completely and carefully.

Improper installation, adjustment, alteration,

service or maintenance can cause injury or

property damage. For assistance or additional

information, consult a qualified installer, service

agency, manufacturer (dealer) or your gas

supplier.

Installation of this cooktop must conform with

local codes, or in the absence of local codes, with

the National Fuel Gas Code, ANSI Z223.1/NFPA.54

or, in Canada, the Natural Gas and Propane

Installation Code, CSA B149.1.

As with any appliance using gas and generating

heat, there are certain safety precautions you

should follow. You will find these precautions in

the IMPORTANT SAFETY INSTRUCTIONS chapter.

Read them carefully.

IMPORTANT:

• Save these instructions for the local electrical

inspector's use.

• Observe all governing codes and ordinances.

NOTE

• Installer: Leave these instructions with the

appliance after installation is completed.

• Consumer: Keep the owner's manual and

installation manual for future reference.

• This appliance must be properly grounded.

• The electrical diagram is in an envelope attached

to the back of the cooktop.

• Skill level – Installation of this appliance requires

basic mechanical skills.

• Proper installation is the responsibility of the

installer.

• Product failure due to improper installation is

not covered under the Warranty.

• Remove all tape and packaging.

• Make sure the burners are properly seated and

level.

• Take the accessory pack off of the cooktop.

• Check to be sure that no cooktop parts have

come loose during shipping.

In the Commonwealth of

Massachusetts

• This product must be installed by a licensed

plumber or gas fitter.

• When using ball type gas shut-off valves, they

must be the T-handle type.

• A flexible gas connector, when used, must not

exceed 3 feet in length.

Tools and Materials

Tools You Will Need

aPhillips Screwdriver

bFlat-blade Screwdriver

cOpen-end or Adjustable Wrench

dPencil and Ruler

ePipe Wrench (2 ea) (one for support)

Materials You May Need

aJoint Sealant

bPipe Fittings

cShut Off Valve

dFlexible Connector

• Gas line shut-off valve

us_main.book.book Page 6 Thursday, May 12, 2022 9:01 AM

7INSTALLATION

ENGLISH

• To reduce the possibility of gas leaks, apply

Teflon tape or a thread compound approved for

use with LP or natural gases to all threaded

connections.

• Flexible metal appliance connector (5/8” I.D.) A 3-

foot length is recommended for ease of

installation but other lengths are acceptable.

Never use an old connector when installing a

new cooktop.

• Flare union adapter for connection to gas supply

line (3/4” or 1/2” NPT x 5/8” I.D.)

• Flare union adapter for connection to pressure

regulator on cooktop. (1/4” NPT x 1/2” I.D.)

• Liquid leak detector or soapy water

Dimensions and Clearances

Provide enough clearance between the cooktop and adjacent combustible surfaces. These dimensions

must be met for safe use of your cooktop. The location of the electrical outlet and pipe opening may be

adjusted to meet specific requirements.

The cooktop must be placed with at least 2 3/4” of clearance to the back wall.

aMake sure wall coverings, countertop and cabinets around cooktop can withstand the heat (up to 200

℉) generated by the cooktop

bTo ensure accuracy, it is best to make a template when cutting the opening in the counter

aRecommended gas supply location

bFrom cutout center line

c1” min. from back wall

us_main.book.book Page 7 Thursday, May 12, 2022 9:01 AM

8INSTALLATION

Installing the Cooktop

Installing the Cooktop Unit

1 Locate the electrical outlet and gas shut-off

valve beneath the cabinet.

Never reuse old flexible connectors.

Install a manual shut-off valve b in the gas

line in an easily accessible location outside the

cooktop. Be sure you know how and where to

shut off the gas supply to the cooktop. Install

the electrical outlet 12˝ a below the

countertop.

2 Carefully lower the cooktop into the

countertop cutout, making sure not to trap

any wires.

3 Remove the retainer brackets from the

literature package.

4 Install the retainer brackets a to the bottom

of the cooktop unit c. then snug the screws

b against the bottom of the countertop d as

shown.

-Dimension/Clearance 30″ Cooktop 36″ Cooktop

A Width of upper plate 30″36″

B Depth of upper plate 21 11/16″

C Height of cooktop base 3 3/4″

D Width of cooktop base 28 1/4″33 5/8″

E Depth of cooktop base 19 3/8″

F Width of cutout 28 1/2″33 15/16″

G Depth of cutout 19 11/16″

H Distance from cutout to side wall on the left of unit. / Distance

from cutout to side wall on the right of the unit.

211 13/16″

I Distance from front edge of cutout to front edge of countertop 21 5/8″

J Distance between cutout and the wall behind the cooktop 22 3/4″

K Width of unprotected overhead cabinets 230″236″

L Depth of unprotected overhead cabinets 113″

M Clearance from countertop to unprotected overhead surface 230″

N Clearance from countertop to nearest cabinet on either side of

unit

218″

us_main.book.book Page 8 Thursday, May 12, 2022 9:01 AM

9INSTALLATION

ENGLISH

NOTE

• The retainer brackets MUST be installed to meet

local codes or, in their absence, the National

Electrical Code ANSI/NFPA No. 70, latest edition.

1. Providing Adequate Gas Supply

This cooktop is designed to operate at a pressure

of 5” of water column with natural gas or 10” of

water column with LP, propane or butane gas.

Make sure you are supplying your cooktop with

the type of gas for which it is designed.

This cooktop is convertible for use with natural or

propane gas. When using this cooktop with LP gas,

the conversion must be made by a qualified LP

installer before attempting to operate the cooktop

using that gas.

For correct operation, the pressure of natural gas

supplied to the regulator should be between 5”

and 13” of water column.

For LP gas, the pressure supplied must be between

10” and 13” of water column.

When checking for correct operation of the

regulator, the inlet pressure must be at least 1”

more than the operating (manifold) pressure as

given above.

The pressure regulator located at the inlet of the

cooktop manifold must remain in the supply line

regardless of whether natural or LP gas is being

used.

A flexible metal appliance connector used to

connect the cooktop to the gas supply line must

have an I.D. of 5/8” and must be a maximum of 3

feet in length for easy installation. In Canada,

flexible connectors should be single wall metal

connectors less than 6 feet in length.

2. Connecting the Cooktop to Gas

Shut off the main gas supply valve before

removing the old cooktop and leave it off until the

new hook-up has been completed. Don’t forget to

relight the pilot on other gas appliances when you

turn the gas back on.

Because hard piping restricts movement of the

cooktop, the use of a CSA International-certified

flexible metal appliance connector is

recommended unless local codes require a hard-

piped connection.

Never reuse an old connector when installing a

new cooktop. If the hard piping method is used,

you must carefully align the pipe; the cooktop

cannot be moved after the connection is made.

To prevent gas leaks, put pipe joint compound on

all male (external) pipe threads.

1 Install a manual gas line shut-off valve in the

gas line in an easily accessed location outside

of the cooktop. Be sure everyone operating

the cooktop knows where and how to shut off

the gas supply to the cooktop.

2 Install a male 1/2” flare union adapter to the

1/2” NPT internal thread at the inlet of the

pressure regulator. Use a backup wrench on

the pressure regulator fitting to prevent

damage.

3 Install a male 1/2” or 3/4” flare union adapter

to the NPT internal thread of the manual shut-

off valve, taking care to back-up the shut-off

valve to keep it from turning.

4 Connect a flexible metal connector to the

adapter on the cooktop. Position the cooktop

to permit connection at the shut-off valve.

5 When all connections have been made, be

sure all cooktop controls are in the off

position and turn on the main gas supply

valve. Check for gas leaks using a manometer.

If a manometer is not available, turn the gas

supply to the cooktop on and use a liquid leak

detector at all joints and connections to check

us_main.book.book Page 9 Thursday, May 12, 2022 9:01 AM

10 INSTALLATION

for leaks. Tighten all connections, if necessary,

to prevent gas leakage in the cooktop or

supply line.

WARNING

• DO NOT USE A FLAME TO CHECK FOR GAS LEAKS.

• The appliance and its individual shutoff valve

must be disconnected from the gas supply

piping system during any pressure testing of

that system at test pressures in excess of 1/2 psi

(3.5 kPa).

• The appliance must be isolated from the gas

supply piping system by closing its individual

manual shutoff valve during any pressure

testing of the gas supply piping system at test

pressures equal to or less than 1/2 psi (3.5 kPa).

Flexible Connector Hookup

aPressure Regulator

bAdapter

cGas Flow into Range

dFlex Connector (3 ft. max. in US, 6 ft. max. in

Canada)

eAdapter

fGas Shut-off Valve

g1/2” or 3/4” Gas Pipe

NOTE

• Installer: Inform the consumer of the location of

the gas shut-off valve.

3. Electrical Connections

Electrical Requirements

This cooktop requires a 120 Volt, 60 Hertz,

properly grounded dedicated circuit protected by

a 15 A or 20 A circuit breaker or time-delay fuse.

The appliance, when installed, must be electrically

grounded in accordance with local codes or, in the

absence of local codes, with the National Electrical

Code, NFPA70 or the Canadian Electric Code, CSA

C22.1-02.

Grounding

IMPORTANT: FOR PERSONAL SAFETY, THIS

APPLIANCE MUST BE PROPERLY GROUNDED.

Preferred Method

aEnsure proper ground exists before use.

The power cord of this appliance should be

equipped with a three-prong (grounding) plug

which mates with a standard three-prong

grounding wall receptacle to reduce the possibility

of electric shock hazard from this appliance.

The customer should have the wall receptacle and

circuit checked by a qualified technician to be sure

the receptacle is properly grounded.

When connecting this cooktop, it is the personal

responsibility and obligation of the customer to

have a standard two-prong wall receptacle

replaced with a properly grounded three-prong

wall receptacle.

DO NOT, UNDER ANY CIRCUMSTANCES, CUT OR

REMOVE THE THIRD (GROUND) PRONG FROM THE

POWER CORD.

A word about Ground Fault Circuit Interrupters – A

Ground Fault Circuit Interrupter (GFCI) is not

required or recommended for gas range

receptacles.

us_main.book.book Page 10 Thursday, May 12, 2022 9:01 AM

11INSTALLATION

ENGLISH

GFCIs are devices that sense leakage of current in

a circuit and automatically switch off power when

a threshold leakage level is detected.

These devices must be manually reset by the

customer.

The National Electrical Code requires the use of

GFCIs in kitchen receptacles installed to serve

countertop surfaces.

Performance of the cooktop will not be affected if

it is operated from a circuit protected by a GFCI,

but resetting the circuit can become a nuisance.

CAUTION

• If needed, have the circuit checked by a qualified

technician to make sure the receptacle is

correctly grounded.

DO NOT use an adapter plug because

disconnection of the power cord places undue

strain on the adapter and causes eventual failure

of the adapter ground terminal.

If only a two-prong wall receptacle is available, it

must be replaced with a three-prong (grounding)

receptacle by a qualified electrician before

plugging in the cooktop.

The installation of appliances designed for

manufactured (mobile) home installation must

conform with the Manufactured Home

Construction and Safety Standard, Title 24 CFR,

Part 3280 [formerly the Federal Standard for

Mobile Home Construction and Safety, Title 24,

HUD (Part 280)] or with local codes where

applicable.

4. Sealing the Openings

Seal any openings in the wall behind the cooktop

and in the floor of the cabinet when hookups are

completed.

5. Assembling the Surface Burners

CAUTION

• DO NOT operate the burners without all parts in

place.

Place the burner caps and heads on the cooktop.

Make sure that the caps and heads are placed in

the correct locations.

aMedium Burner Head and Cap

bExtra Large Burner (Center) Head and Cap

cSmall Burner Head and Cap

dLarge Burner Head and Cap

Make sure the hole a in the burner head is

positioned over the electrode b.

6. Checking Ignition of Surface

Burners

Operation of all cooktop burners should be

checked after the cooktop and gas supply lines

have been carefully checked for leaks.

Electric Ignition

Select a top burner knob, push down and then

turn counterclockwise to the LITE position.

You can hear a clicking sound indicating proper

operation of the spark module.

Once the air has been purged from the supply

lines, burners should ignite within 4 seconds.

After the burner ignites, rotate the knob out of the

LITE position. Try each burner in succession until

all burners have been checked.

The combustion quality of the burner flames

needs to be confirmed visually.

a Yellow flames — Call for

service

us_main.book.book Page 11 Thursday, May 12, 2022 9:01 AM

12 INSTALLATION

If burner flames look like a, call for service. b or

c is normal for burner flames, depending on the

type of gas you use.

With LP gas, some yellow tipping on outer cones is

normal.

7. Adjusting the Surface Burner Low

Flame (Simmer) Setting

1 Light all surface burners.

2 Turn the knob on the burner being adjusted

to LO (LOW).

3 Remove the knob.

4 On center and right front knob rings only,

remove the plastic cover a on the knob ring

by turning it counterclockwise.

5 For single-valve burners (left front, left rear,

right rear), insert a small, flat-blade

screwdriver into the valve stem.

For dual-valve burners (center, right front),

insert a small, flat-blade screwdriver into the

hole to the left of the valve stem.

aSingle Valve Adjustment Screw

bDual Valve Adjustment Screw

6 Turn the adjustment screw until the flame

reaches the desired size.

7 Replace the knob.

8 Test the flame stability.

Test 1

•Turn the knob from HI to LOW quickly.

• lf the flame goes out, increase the flame

size and test again.

Test 2

• With the burner on a LOW setting, open and

close the oven or cabinet door quickly.

• If the flame is extinguished by the air

currents created by the door movement,

increase the flame height and test again.

9 Repeat steps 1 - 6 for each surface burner.

10 After setting the low flame, turn off the

burner.

b Yellow tips on outer cones —

Normal for LP gas

c Soft blue flames — Normal for

natural gas

us_main.book.book Page 12 Thursday, May 12, 2022 9:01 AM

13APPENDIX

ENGLISH

APPENDIX

Checking Operation

Final Check

When All Hookups are Complete

Make sure all controls are left in the off position.

Make sure the flow of combustion and ventilation

air to the cooktop is unobstructed.

Converting to LP Gas (or Converting

Back to Natural Gas from LP)

This cooktop leaves the factory set for use with

natural gas. When converting to LP gas, the

conversion must be performed by a qualified LP

gas installer.

The conversion instructions and LP orifices are

supplied with your cooktop.

Keep these instructions and the orifices in case you

want to convert back to natural gas.

us_main.book.book Page 13 Thursday, May 12, 2022 9:01 AM

14 Memo

us_main.book.book Page 14 Thursday, May 12, 2022 9:01 AM

MANUAL DEL PROPIETARIO

GAS COOKTOP

Lea el manual del propietario detenidamente previo a operar el

electrodoméstico y mantengalo al alcance para futuras

referencias.

ESPAÑOL

www.lg.com

ls_main.book.book Page 1 Thursday, May 12, 2022 3:21 PM

Seguridad para una placa de cocción de gas

ADVERTENCIA: Si no sigue con exactitud la información de

este manual, puede provocar un incendio o una explosión que cause

daños en la propiedad, lesiones personales o la muerte.

•No guarde ni use gasolina u otros vapores o líquidos inflamables cerca

de este aparato o cualquier otro.

•QUÉ HACER SI HUELE GAS

-No intente encender ningún aparato.

-No toque ningún interruptor eléctrico.

-No use ningún teléfono en su edificio.

-Llame a su compañía de gas inmediatamente desde el teléfono de un

vecino. Siga las instrucciones de la compañía de gas.

-Si no puede comunicarse con su compañía de gas, llame al

departamento de bomberos.

•Un instalador calificado, una agencia de servicio o la compañía de gas

deben realizar la instalación y mantenimiento.

ADVERTENCIA:

Nunca deje la sección de cocción de superficie de este aparato sin

supervisión.

•El incumplimiento de esta advertencia puede provocar incendios,

explosiones o riesgos de quemaduras que causen daños en la

propiedad, lesiones personales o la muerte.

•En caso de incendio, manténganse alejado del electrodoméstico y

llame de inmediato al departamento de bomberos local.

NO INTENTE APAGAR CON AGUA UN INCENDIO PROVOCADO POR

ACEITE/GRASA.

ls_main.book.book Page 6 Tuesday, May 3, 2022 10:40 AM

ÍNDICE

4 INSTRUCCIONES IMPORTANTES

DE SEGURIDAD

4 LEA TODAS LAS INSTRUCCIONES ANTES DE

UTILIZAR

4 ADVERTENCIA

6INSTALACIÓN

6 Antes de instalar

8 Instalación de la placa de cocción

14 APÉNDICE

14 Comprobación del funcionamiento

ls_main.book.book Page 3 Thursday, May 12, 2022 3:21 PM

4INSTRUCCIONES IMPORTANTES DE SEGURIDAD

INSTRUCCIONES IMPORTANTES DE SEGURIDAD

LEA TODAS LAS INSTRUCCIONES ANTES DE UTILIZAR

Descargue este manual del propietario en http://www.lg.com

Mensajes de seguridad

Su seguridad y la de los demás son muy importantes.

Tanto en este manual como en el equipo, hemos proporcionado muchos mensajes de seguridad

importantes. Siempre debe leer y respetar todos los mensajes de seguridad.

Todos los mensajes de seguridad le indicarán cuáles son los peligros potenciales, cómo reducir la

posibilidad de lesiones y qué podría suceder si no sigue las instrucciones.

ADVERTENCIA

• Para reducir el riesgo de explosiones, incendios, descargas eléctricas, quemaduras, lesiones o muerte de

las personas al usar este producto, siga las precauciones básicas, incluidas las siguientes:

Instalación

• Retire la cinta y todo el material de empaque antes de usar la placa de cocción. Deseche todas las bolsas

de plástico después de desembalar la placa de cocción. No permita que los niños jueguen con el material

de empaque.

• No reutilice los conectores flexibles antiguos. Su uso puede causar pérdidas de gas y lesiones a las

personas. Siempre utilice conectores flexibles NUEVOS al instalar un electrodoméstico a gas.

• Retire todo el material de empaque y los folletos antes de conectar el suministro de gas y eléctrico.

• La instalación de la placa de cocción debe hacerla un instalador calificado.

• Su placa de cocción debe estar conectada eléctricamente a tierra según los códigos locales o, si no

existieran tales códigos, según el Código Eléctrico Nacional (ANSI/NFPA 70, última edición). En Canadá, la

conexión eléctrica a tierra debe hacerse según el Código Eléctrico Canadiense actual CSA C22.1, Parte 1 y

los códigos locales. Consulte el paso 3, Conexiones eléctricas, en este manual.

• Asegúrese de que los revestimientos de las paredes que están alrededor de la placa de cocción puedan

soportar el calor de 200 ℉ cómo máximo que genera el electrodoméstico.

• La campana de ventilación debe estar hecha de metal en láminas que no superen 0.0122" de espesor.

Instálela encima de la placa de cocción y deje un espacio de al menos 1/4" entre la campana y la parte

inferior del gabinete de metal o el material combustible. La campana debe tener al menos el mismo

ancho que el electrodoméstico y estar centrada encima de él. El espacio entre la superficie de cocción y

la superficie de la campana de ventilación NUNCA DEBE SER MENOR DE 24 PULG.

Este es el símbolo de alerta de seguridad.

Este símbolo le advierte sobre posibles riesgos que pueden ocasionar lesiones o la muerte a usted o

a otros. El símbolo de alerta de seguridad siempre estará acompañado de las palabras

"ADVERTENCIA" o "PRECAUCIÓN" y seguido de un mensaje de seguridad importante.

Estos términos significan lo siguiente:

ADVERTENCIA

El incumplimiento de las instrucciones podría causarle la muerte o lesiones graves.

PRECAUCIÓN

El incumplimiento de las instrucciones podría causarle lesiones o daños al producto.

ls_main.book.book Page 4 Thursday, May 12, 2022 3:21 PM

5INSTRUCCIONES IMPORTANTES DE SEGURIDAD

ESPAÑOL

GUARDE ESTAS INSTRUCCIONES

EXCEPCIÓN: La instalación de un horno microondas o un electrodoméstico de cocina sobre la placa de

cocción deben cumplir con las instrucciones de instalación incluidas con el electrodoméstico.

• Si los gabinetes están ubicados encima de la placa de cocción, deje un espacio mínimo de 30" entre la

superficie de cocción y la base de los gabinetes no protegidos.

• Si no puede dejar un espacio de 30" entre la superficie de cocción y el material combustible o los

gabinetes de metal que están encima de ella, proteja la parte inferior de los gabinetes que se

encuentran arriba de la placa de cocción con un cartón aislante que no sea menor de 1/4" cubierto con

un metal en lámina de 0.0122" de espesor como mínimo. El espacio entre la superficie de cocción y los

gabinetes protegidos NUNCA DEBE SER MENOR DE 24 PULG.

• La distancia vertical desde el plano de la superficie de cocción hasta la base de los gabinetes adyacentes

ubicados sobre ella que se encuentren a menos de 1" de los lados de la placa de cocción no debe ser

menor de 18". (Consulte la ilustración de Dimensiones y espacios en este manual.)

• No obstruya las aberturas de aire de ventilación o combustión.

• La prueba para detectar fugas del electrodoméstico se debe realizar según las instrucciones del

fabricante.

• No deben guardarse elementos que sean del interés de los niños en los gabinetes ubicados encima de la

placa de cocción.

- Si los niños intentan trepar sobre la placa de cocción pueden sufrir lesiones graves.

• Este electrodoméstico no debe instalarse con un sistema de ventilación que sople viento hacia abajo en

dirección a la placa de cocción. Este tipo de sistema de ventilación puede causar problemas de ignición y

combustión con el electrodoméstico de cocina a gas y causar lesiones a las personas o un

funcionamiento no deseado.

ls_main.book.book Page 5 Thursday, May 12, 2022 3:21 PM

6INSTALACIÓN

INSTALACIÓN

Antes de instalar

Antes de comenzar

Lea estas instrucciones atentamente. La

instalación, el ajuste, la alteración, el

mantenimiento o servicio inadecuados pueden

causar lesiones o daños a la propiedad. Para

obtener ayuda o información adicional, consulte a

un instalador calificado, una agencia de

mantenimiento, al fabricante (comerciante) o a su

proveedor de gas.

La instalación de esta placa de cocción debe

cumplir con los códigos locales o en ausencia de

ellos, con el Código Nacional de Gas Combustible,

ANSI Z223.1/NFPA.54 o, en Canadá, con el Código

de Instalación de Gas Natural y Propano, CSA

B149.1.

Como con todo electrodoméstico que utiliza gas y

genera calor, se deben tomar ciertas precauciones

de seguridad. Puede encontrarlas en el capítulo

INSTRUCCIONES IMPORTANTES DE SEGURIDAD.

Léalas atentamente.

IMPORTANTE:

• Guarde estas instrucciones para que pueda

utilizarlas el inspector de electricidad local.

• Cumpla todos los códigos y ordenanzas

vigentes.

NOTA

• Instalador: deje estas instrucciones con el

electrodoméstico después de completar la

instalación.

• Usuario: guarde el manual del propietario y el

manual de instalación para futuras consultas.

• Este electrodoméstico debe estar conectado a

tierra de manera adecuada.

• El diagrama eléctrico se encuentra en un sobre

en la parte posterior de la placa de cocción.

• Nivel de habilidad: la instalación de este

electrodoméstico requiere habilidades

mecánicas básicas.

• El instalador es responsable de su correcta

instalación.

• La falla del producto causada por una instalación

inadecuada no está cubierta por la garantía.

• Retire toda la cinta y el empaque.

• Asegúrese de que los quemadores estén bien

asentados y nivelados.

• Separe el paquete de accesorios de la placa de

cocción.

• Compruebe que no haya quedado suelta

ninguna pieza de la placa de cocción durante el

envío.

En el Commonwealth de

Massachusetts

• Un plomero certificado o un instalador de gas

deben instalar este producto.

• Cuando utilice válvulas de bola para corte de

gas, deben ser manijas en T.

• Cuando se use, el conector de gas flexible no

debe exceder los 3 pies de largo.

Herramientas y materiales

Herramientas que necesitará

aDestornillador Phillips

bDestornillador de hoja plana

cLlave de extremo abierto o ajustable

dLápiz y regla

eLlave para tuberías (2 c/u) (una para apoyo)

Materiales que puede necesitar

aSellador de juntas

ls_main.book.book Page 6 Thursday, May 12, 2022 3:21 PM

La page charge ...

LG STUDIO LSCG307ST Guide d'installation

Marque: LG STUDIO

Modèle: LSCG307ST

Taper: Guide d'installation

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: LG STUDIO LSCG307ST Installation guide
español: LG STUDIO LSCG307ST Guía de instalación

Documents connexes

LG STUDIO SDWD24P3 Le manuel du propriétaire

LG STUDIO LSCG307ST Guide d'installation

Ce manuel convient également à

LG STUDIO LSCG307ST Guide d'installation

dans d''autres langues

Documents connexes

Autres documents