LG CBGJ3027 Gas Cooktop Le manuel du propriétaire

Catégorie
Cuisinières
Taper
Le manuel du propriétaire
항목 Spec.
재질 모조지
평량 80
사이즈 B5
표지 여부 유
페이지 92
인쇄 도수 1
OWNER'S MANUAL
GAS COOKTOP
Read this owner's manual thoroughly before operating the
appliance and keep it handy for reference at all times.
ENGLISH
CBGJ3027* CBGJ3627* CBGJ3023* CBGJ3623*
MFL71937802
Rev.00_110422
www.lg.com
Copyright © 2022 LG Electronics Inc. All Rights Reserved.
Scan to see the online manual.
en-us_main.book.book Page 1 Thursday, November 3, 2022 3:13 PM
Safety for a Gas Cooktop
WARNING: If the information in these instructions is not
followed exactly, a fire or explosion may result causing property damage,
personal injury or death.
Do not store or use gasoline or other flammable vapors and liquids in
the vicinity of this or any other appliance.
WHAT TO DO IF YOU SMELL GAS
-Do not try to light any appliance.
-Do not touch any electrical switch.
-Do not use any phone in your building.
-Immediately call your gas supplier from a neighbor's phone. Follow
the gas supplier's instructions.
-If you cannot reach your gas supplier, call the fire department.
Installation and service must be performed by a qualified installer,
service agency, or the gas supplier.
WARNING:
Never Operate the Top Surface Cooking Section of this Appliance
Unattended.
Failure to follow this warning statement could result in fire,
explosion, or burn hazard that could cause property damage,
personal injury, or death.
If a fire should occur, keep away from the appliance and
immediately call your fire department.
DO NOT ATTEMPT TO EXTINGUISH AN OIL/GREASE FIRE WITH
WATER.
us_main.book.book Page 6 Tuesday, May 3, 2022 10:34 AM
TABLE OF CONTENTS
3
4 IMPORTANT SAFETY
INSTRUCTIONS
4 READ ALL INSTRUCTIONS BEFORE USE
4 WARNING STATEMENTS
7 CAUTION STATEMENTS
8 PRODUCT OVERVIEW
8 Product Features
9 OPERATION
9 Using the Surface Burners
13 SMART FUNCTIONS
13 LG ThinQ Application
16 MAINTENANCE
16 Care and Cleaning
20 TROUBLESHOOTING
20 Before Calling for Service
22 LIMITED WARRANTY
22 USA
26 CANADA
en-us_main.book.book Page 3 Thursday, November 3, 2022 3:13 PM
4IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE
Safety Messages
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and
follow all safety messages.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury,
and tell you what may happen if the instructions are not followed.
WARNING STATEMENTS
WARNING
To reduce the risk of explosion, fire, death, electric shock, scalding or injury to persons when using this
product, follow basic precautions, including the following:
Installation
Make sure the cooktop is properly installed and grounded by a qualified installer, according to the
Installation Instructions. Any adjustment and service should be performed only by qualified gas range
installers or service technicians.
Plug the cooktop into a 120-volt grounded outlet only. Do not remove the round grounding prong from
the plug. If in doubt about the grounding of the home electrical system, it is your personal responsibility
and obligation to have an ungrounded outlet replaced with a properly grounded, three-prong outlet in
accordance with the National Electrical Code. Do not use an extension cord with this cooktop.
To prevent fire hazard or electrical shock, do not use an adapter plug, an extension cord, or remove the
grounding prong from the electrical power cord. Failure to follow this warning can cause serious injury,
fire or death.
This appliance is equipped with a three-prong grounding plug for your protection against shock hazard
and should be plugged directly into a properly grounded receptacle. Do not cut or remove the
grounding prong from this plug.
Make sure all packaging materials are removed from the cooktop before operating it to prevent fire or
smoke damage should the packaging material ignite.
Make sure the cooktop is properly adjusted by a qualified service technician or installer for the type of
gas (natural or LP) that is to be used. The cooktop can be converted for use with either type of gas. See
the Installation Instructions.
These adjustments must be done by a qualified service technician according to the manufacturer’s
instructions and all codes and requirements of the authority having jurisdiction. Failure to follow these
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or injure you and others. All safety messages
will follow the safety alert symbol and either the word WARNING or CAUTION.
These words mean:
WARNING
You may be killed or seriously injured if you do not follow instructions.
CAUTION
You may be injured or cause damage to the product if you do not follow instructions.
en-us_main.book.book Page 4 Thursday, November 3, 2022 3:13 PM
5IMPORTANT SAFETY INSTRUCTIONS
ENGLISH
instructions could result in serious injury or property damage. The qualified agency performing this
work assumes responsibility for the conversion.
Remove all tape and packing materials before using the cooktop. Dispose of all plastic bags after
unpacking the cooktop. Never allow children to play with packing materials.
Improper installation, adjustment, alteration, service or maintenance can cause injury or property
damage. For assistance or additional information, consult a qualified installer, service agency,
manufacturer (dealer) or your gas supplier.
Never reuse old flexible connectors. The use of old flexible connectors can cause gas leaks and personal
injury. Always use NEW flexible connectors when installing a gas appliance.
This appliance must not be installed with a ventilation system that blows air downward toward the
cooktop. This type of ventilation system may cause ignition and combustion problems with the gas
cooking appliance resulting in personal injury or unintended operation.
Ask the installer to show you the location of the cooktop gas shut-off valve and how to shut it off if
necessary.
Before servicing, disconnect the electrical supply.
Operation
Gas appliances can cause minor exposure to four potentially hazardous substances, namely benzene,
carbon monoxide, formaldehyde and soot, caused primarily by the improper combustion of natural or
LP gas.
Correctly adjusted burners, indicated by a blue rather than a yellow flame, will minimize improper
combustion. Exposure to these substances can be minimized by opening windows or using a ventilation
fan or hood.
Do not place or use combustible materials, gasoline or other flammable vapors and liquids in the vicinity
of this or any other appliance.
Stepping, leaning or sitting on this cooktop can result in serious injuries and cause damage to the
cooktop.
Do not leave children alone or unattended where a cooktop is hot or in operation. They could be
seriously burned.
Do not allow children to climb or play around the cooktop.
Let the burner grates and other surfaces cool before touching them or leaving them where children can
reach them.
Items of interest to children should not be stored in cabinets above a cooktop — children climbing on
the cooktop to reach items could be seriously injured.
Do not let anyone climb or stand on the cooktop. They could damage the cooktop or tip it over, causing
severe personal injury.
NEVER use the cooktop as a space heater to heat or warm the room. Doing so may result in carbon
monoxide poisoning and overheating of the cooktop.
Never wear loose fitting or hanging garments while using the appliance. Be careful when reaching for
items placed in cabinets over the cooktop. Flammable material could be ignited if brought into contact
with flame or hot surfaces and may cause severe burns.
Do not place flammable materials on or near the cooktop.
Do not use water on grease fires. NEVER touch a flaming pan. Turn the controls off. Smother a flaming
pan on a surface burner by covering the pan completely with a well-fitting lid, cookie sheet or flat tray.
Use a multi-purpose dry chemical or foam-type fire extinguisher. Flaming grease outside a pan can be
put out by covering it with baking soda or, if available, by using a multi-purpose dry chemical or foam-
type fire extinguisher.
If the top burner flame goes out, gas is still flowing to the burner until the knob is turned to the OFF
position. Do not leave the burners ON unattended.
en-us_main.book.book Page 5 Thursday, November 3, 2022 3:13 PM
6IMPORTANT SAFETY INSTRUCTIONS
Use proper pan size. Do not use pans that are unstable or easily tipped. Select cookware having flat
bottoms large enough to cover burner grates. To avoid spills, make sure cookware is large enough to
contain the food properly. This will save cleaning time and prevent hazardous accumulations of food.
Because heavy spattering or spills left on a range can ignite, use pans with handles that can be easily
grasped and remain cool.
Never leave the surface burners unattended at high flame settings. Boilovers can cause smoking and
greasy spillovers may catch on fire.
Control the top burner flame size so it does not extend beyond the edge of the cookware. Excessive
flame is hazardous.
Use only dry pot holders—moist or damp pot holders on hot surfaces may result in burns from steam.
Do not let pot holders come near open flames when lifting cookware. Do not use a towel or other bulky
cloth instead of a pot holder.
To prevent burns, ignition of flammable materials and spillage, turn cookware handles toward the side
or back of the cooktop without extending over adjacent burners.
NEVER place any items on the cooktop. The hot air from the vent may ignite flammable items and will
increase pressure in closed containers, which may cause them to burst.
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other
appliance.
Storage on Appliance - Flammable materials should not be stored on the cooktop or near surface units.
This includes paper, plastic and cloth items, such as cookbooks, plasticware and towels, as well as
flammable liquids.
Carefully watch foods being fried at a high flame setting.
Always heat fat slowly, and watch as it heats.
Use a deep fat thermometer if possible to prevent overheating fat beyond the smoking point.
Use the least possible amount of fat for effective shallow or deep-fat frying. Filling the pan too full of fat
can cause spillovers when food is added.
LG does not recommend using a gas cooktop for the preparation of flaming foods. If you choose to
prepare flaming foods under a hood, turn the fan on.
To prevent burns, always be sure that the controls for all burners are at the OFF position and all grates
are cool before attempting to remove them.
If you smell gas, turn off the gas to the cooktop and call a qualified service technician. Never use an open
flame to locate a leak.
Do not place cooking oils or other flammable materials on or near the cooktop.
Always turn knob to the OFF position before removing cookware.
Do not store explosives, such as aerosol cans, on or near the cooktop. Flammable materials may explode
and result in fire or property damage.
Do not obstruct the flow of combustion and ventilation air.
Do not block the airflow into or out of the cooktop. It is necessary for proper combustion and ventilation.
Always turn knobs to the LITE position when igniting the top burners and make sure the burners have
ignited.
If frying a combination of oils or fats, stir together before heating or as fats slowly melt.
Liquids such as water, coffee or tea are able to be overheated beyond the boiling point without
appearing to be boiling, due to surface tension of the liquid. Visible bubbling or boiling is not always
present when the container is removed from the cooktop. This could result in very hot liquids suddenly
boiling over when the container is disturbed or a spoon or other utensil is inserted into the liquid.
To reduce the risk of injury to persons
- Do not overheat the liquid.
- Stir the liquid both before and halfway through heating it.
- Do not use straight-sided containers with narrow necks.
en-us_main.book.book Page 6 Thursday, November 3, 2022 3:13 PM
7IMPORTANT SAFETY INSTRUCTIONS
ENGLISH
SAVE THESE INSTRUCTIONS
- After heating, allow the container to stand on the cooktop for a short time before moving the
container.
- Use extreme care when inserting a spoon or other utensil into the container after heating.
Maintenance
Do not attempt to repair or replace any part of the cooktop unless it is specifically mentioned in this
manual. All other service should be referred to a qualified technician.
Clean the cooktop with caution. If a wet sponge or cloth is used to wipe spills on a hot cooktop, be careful
to avoid steam burns.
Leak testing of the appliance shall be conducted according to the manufacturer’s instructions.
Do not lift the cooktop. Lifting the cooktop can cause damage and improper operation of the cooktop.
If the cooktop is located near a window, do not hang long curtains that could blow over the surface
burners and catch on fire.
CAUTION STATEMENTS
CAUTION
To reduce the risk of minor or moderate injury to persons, malfunction, or damage to the product or
property when using this product, follow basic precautions, including the following:
Operation
To prevent poor air circulation, place the cooktop out of the kitchen traffic path and away from drafty
locations.
If using glass cookware, make sure it is designed for top-of-range cooking.
If frying mixtures of oils or fats, stir to combine before heating.
Do not use a wok on the surface burners if the wok has a round metal ring that is placed over the burner
grate to support the wok. This ring acts as a heat trap, which may damage the burner grate and burner
head. Also, it may cause the burner to work improperly. This may cause a carbon monoxide level above
that allowed by current standards, resulting in a health hazard.
Foods for frying should be as dry as possible. Frost or moisture on foods can cause hot fat to bubble up
and over the sides of the pan.
Never try to move a pan of hot fat, especially a deep fat fryer. Wait until the fat is cool.
Do not place plastic items on the cooktop—they may melt if left too close to the vent.
Keep all plastics away from the surface burners.
To avoid burns, do not clean the cooktop surface until it has cooled.
en-us_main.book.book Page 7 Thursday, November 3, 2022 3:13 PM
8PRODUCT OVERVIEW
PRODUCT OVERVIEW
Product Features
Parts and Features
This feature is only available on some models.
aGrate
bBurner
cBurner Control Knob
dRating Label and Serial Number Plate
eWi-Fi Button
Accessories
This feature is only available on some models.
aRetainer Brackets (2 ea)
bScrews (2 ea)
cScrews (4 ea)
dNozzles
CBGJ3027*, CBGJ3627*: 6 ea
CBGJ3023*, CBGJ3623*: 5 ea
eGriddle(1 ea)
NOTE
For your safety and for extended product life,
only use authorized components.
The manufacturer is not responsible for product
malfunction or accidents caused by the use of
separately purchased, unauthorized
components or parts.
The images in this guide may be different from
the actual components and accessories, which
are subject to change by the manufacturer
without prior notice for product improvement
purposes.
en-us_main.book.book Page 8 Thursday, November 3, 2022 3:13 PM
9OPERATION
ENGLISH
OPERATION
Using the Surface Burners
Before Using the Surface Burners
Throughout this manual, features and appearance
may vary from your model.
Make sure all grates on the cooktop are properly
placed before using any burner.
Be sure the burners and grates are cool before
you place your hand, a pot holder, cleaning
cloths or other materials on them.
Make sure all burners are in place.
Do not operate the burner for an extended
period of time without cookware on the grate.
The finish on the grate may chip without
cookware to absorb the heat.
Lighting a Gas Surface Burner
Be sure all the surface burners are placed in
their respective positions.
Push the control knob in and turn it to the LITE
position.
The clicking noise you hear is the sound of the
electric spark igniting the burner.
A clicking sound may also be heard during
operation due to the flame detection function.
To control the flame size, turn the knob. lf the
knob stays at LITE, it will continue to click.
When one burner knob is turned to LITE, only
that burner sparks. Do not attempt to
disassemble or clean around any burner while
another burner is on. An electric shock may
result, which could cause you to knock over hot
cookware.
In Case of Power Failure
In case of a power failure, you can light the gas
surface burners on the cooktop with a match.
Hold a lit match to the burner, then push in and
turn the control knob to the LITE position. Use
extreme caution when lighting burners this way.
Surface burners in use when an electrical power
failure occurs will continue to operate normally.
Sealed Gas Burners
The cooktop has five sealed gas burners. They
offer convenience, cleanability and flexibility to
be used in a wide range of cooking applications.
aMedium
bExtra Large
- CBGJ3027*, CBGJ3627*: Dual
- CBGJ3023*, CBGJ3623*: Single
cSmall
dLarge
•The small c burner offers a very low simmer
setting and is best for delicate foods such as
sauces that require long simmer times over low
heat.
The medium a and large d burners are the
primary burners for most cooking. The
temperature range on these burners can handle
a wide range of cooking tasks.
The extra large burner b is the maximum
output burner. Like the other burners, it can be
used for most everyday cooking tasks. This
burner is also designed to quickly bring large
amounts of liquid to a boil. The special
UltraHeat+ settingis designed for use with
cookware 10 inches or larger in diameter. The
extra large dual burner can also be used on LO
to simmer.
e Extra Large Burner only
This feature is only available on some models.
en-us_main.book.book Page 9 Thursday, November 3, 2022 3:13 PM
10 OPERATION
Selecting Flame Size
NEVER let the flames extend up the sides of the
cookware.
Watch the flame, not the knob, while reducing the
heat. When fast heating is desired, the flame size
on a gas burner should match the cookware used.
Flames larger than the bottom of the cookware will
not result in faster heating of the cookware and
could be hazardous.
Cookware
• Aluminum
Medium-weight cookware is recommended
because it heats quickly and evenly. Most of the
foods brown evenly in an aluminum skillet. Use
sauce pans with tight fitting lids when cooking
with minimum amounts of water.
• Cast-Iron
If heated slowly, most skillets will give
satisfactory results.
Stainless Steel
This metal alone has poor heating properties
and is usually combined with copper, aluminum
or other metals for improved heat distribution.
Combination metal skillets usually work
satisfactorily if they are used with medium heat
as the manufacturer recommends.
•Enamelware
Under some conditions, the enamel of some
cookware may melt. Follow cookware
manufacturer’s recommendations for cooking
methods.
•Glass
There are two types of glass cookware - those for
oven use only and those for top of the range
cooking (saucepans, coffee and teapots). Glass
conducts heat very slowly.
Heatproof Glass Ceramic
Can be used for either surface or oven cooking.
It conducts heat very slowly and cools very
slowly. Check cookware manufacturer’s
directions to be sure it can be used on gas
ranges.
Using a Wok
Do not use a wok support ring. Placing the ring
over the burner or grate may cause the burner to
work improperly, resulting in carbon monoxide
levels above allowable standards.
This can be a health hazard.
Use a 14 inch or smaller flat bottom wok. Make
sure the wok bottom sits flat on the grate.
Woks are available at a local retail store.
Only a flat-bottomed wok should be used.
Stove-Top Grills
Do not use stove top grills on the surface burners.
Using the stove top grill on the surface burner will
cause incomplete combustion and can result in
exposure to carbon monoxide levels above
allowable current standards.
This can be a health hazard.
Using the Griddle
The enamel-coated griddle provides an extra -
large cooking surface for meats, pancakes or other
food usually prepared in a frying pan or skillet.
NOTE
The griddle will discolor over time as it becomes
seasoned with use.
How to Place the Griddle
The griddle can only be used on the left side
grate.
The griddle must be properly placed on the
grate.
When the correct side is facing the front, the
tabs on the underside of the griddle sit properly
en-us_main.book.book Page 10 Thursday, November 3, 2022 3:13 PM
11OPERATION
ENGLISH
on the prongs of the grate to keep the griddle
from moving.
NOTE
Do not remove the left side grate when using the
griddle.
CAUTION
Do not remove the griddle plate until the
cooktop grates, surfaces and griddle plate are
completely cooled.
The griddle plate on the cooktop may become
very hot when using the cooktop. Always use
oven mitts when placing or removing the griddle
plate.
Griddle Cooking Guide
Item Cooktop
size
Preheat
setting
Preheat
time
Cook
setting Notes
Pancakes 30" or 36" Medium
High 4 min Medium
High
Flip after 30 seconds to 1-
1/2 minutes
French Toast
30" Medium
High 3-4 min Medium 4-5 minutes per side
36" Medium
High 4-5 min Medium Flip after 2 to 2-1/2
minutes
Fried Eggs 30" or 36" Medium
High 4-5 min Medium
High
Flip after 1-1/2 to 2
minutes
Bacon
30" Medium - Medium 8-12 minutes
36" Medium
High -Medium
High Flip after 6 to 7 minutes
Breakfast Sausage Links
30" Medium
Low -Medium
Low
Put 1/4 cup water on
griddle at start, cook 10-
14 minutes
36" Medium - Medium
Cook for 5-6 minutes,
then rotate every 30
seconds to 1 minute
Breakfast Sausage
Patties
30" Medium 3 min Medium Turn after 5-6 minutes
36" Medium/
Low 4-5 min Medium/
Low
Flip and move patties
every 1-2 minutes
Warming Flour Tortillas 30" or 36" Medium 4-5 min Medium 15-30 seconds per side
Hot Sandwiches (grilled
cheese or quesadillas)
30" Medium 3-4 min Medium 2-3 minutes per side
36" Medium 4 min Medium 45 seconds to 1 minute
per side
Hamburgers 30" or 36" Medium
High 4-5 min Medium
High
Cook for 14 minutes,
flipping every 2-3
minutes
en-us_main.book.book Page 11 Thursday, November 3, 2022 3:13 PM
12 OPERATION
Use this table as a guide. Cooking times will vary depending on quality or quantity of food.
NOTE
Avoid cooking extremely greasy foods, as grease spills can occur.
The griddle can become hot when surrounding burners are in use.
Do not overheat the griddle. This can damage the enamel coating.
Do not cut foods on the griddle.
Do not place or store items on the griddle.
Do not clean the griddle in the dishwasher or in a self-clean oven cycle.
How to Season the Griddle
As with cast-iron cookware, the griddle will acquire
more non-stick properties with use. To shorten this
process, you can season the griddle following
these steps.
1 Apply a light, even coat of vegetable oil across
the entire surface of the griddle, making sure
the oil does not pool or puddle.
2 Place the griddle in an oven on the middle
rack. Set the oven to 550 and bake for one
hour.
3 Turn off the oven and allow the griddle to cool
completely in the oven before removing it.
4 Repeat steps 1 through 3 two more times, for
a total of three seasoning cycles.
Pork Chops
(cook to 145 )30" or 36" Medium
High 3-4 min Medium
High
Let rest for 20 minutes
before cooking. Cook for
14 minutes, flipping
every 3-5 minutes. Let
rest for 5 minutes after
cooking.
Chicken Breasts
30" Medium
High 3-4 min Medium Cook for 10-15 minutes,
flipping every 4-5 minute
36" Medium
High 4 min Medium
High
Cook for 8-12 minutes,
flipping every 4-5
minutes
Searing Steaks 30" or 36" Medium
High 3-4 min Medium
High
Cook for 12-1/2 minutes,
flipping every 3-4
minutes
Item Cooktop
size
Preheat
setting
Preheat
time
Cook
setting Notes
en-us_main.book.book Page 12 Thursday, November 3, 2022 3:13 PM
13SMART FUNCTIONS
ENGLISH
SMART FUNCTIONS
LG ThinQ Application
This feature is only available on models with Wi-Fi.
The LG ThinQ application allows you to
communicate with the appliance using a
smartphone.
LG ThinQ Application Features
Monitoring
- This function helps you check the current
status, remaining time, cook settings and end
time in one place.
Product Notifications
- Turn on the Push Alerts to receive appliance
status notifications. The notifications are
triggered even if the LG ThinQ application is
not open.
Timer
- You can set the timer from the application.
Firmware Update
- Keep the appliance updated.
NOTE
If you change your wireless router, Internet
service provider, or password, delete the
connected appliance from the LG ThinQ
application and connect it again.
This information is current at the time of
publication. The application is subject to change
for product improvement purposes without
notice to users.
Before Using LG ThinQ Application
1 Check the distance between the appliance
and the wireless router (Wi-Fi network).
If the appliance is too far from the router,
the signal strength becomes weak. It may
take a long time to connect or installation
may fail.
2 Turn off the Mobile data or Cellular Data on
your smartphone.
3 Connect your smartphone to the wireless
router.
NOTE
To verify the Wi-Fi connection, check that the f
icon on the control panel is lit.
The appliance supports 2.4 GHz Wi-Fi networks
only. To check your network frequency, contact
your Internet service provider or refer to your
wireless router manual.
LG ThinQ is not responsible for any network
connection problems or any faults, malfunctions,
or errors caused by network connection.
If the appliance is having trouble connecting to
the Wi-Fi network, it may be too far from the
router. Purchase a Wi-Fi repeater (range
extender) to improve the Wi-Fi signal strength.
The Wi-Fi connection may not connect or may be
interrupted because of the home network
environment.
The network connection may not work properly
depending on the Internet service provider.
The surrounding wireless environment can
make the wireless network service run slowly.
If the appliance cannot be connected due to
problems with the wireless signal transmission,
unplug the appliance and wait about a minute
before trying again.
If the firewall on your wireless router is enabled,
disable the firewall or add an exception to it.
The wireless network name (SSID) should be a
combination of English letters and numbers. (Do
not use special characters.)
Smartphone user interface (UI) may vary
depending on the mobile operating system (OS)
and the manufacturer.
If the security protocol of the router is set to
WEP, network setup may fail. Change the
security protocol (WPA2 is recommended) and
connect the product again.
en-us_main.book.book Page 13 Thursday, November 3, 2022 3:13 PM
14 SMART FUNCTIONS
Installing the LG ThinQ Application
Search for the LG ThinQ application from the
Google Play Store or Apple App Store on a
smartphone. Follow instructions to download and
install the application.
Connecting to Wi-Fi
The Wi-Fi button, when used with the LG ThinQ
application, allows the appliance to connect to a
home Wi-Fi network. The LED shows the status of
the appliance’s network connection. The LED lights
up when the appliance is connected to the Wi-Fi
network.
Initial Appliance Connection
Run the LG ThinQ application and follow the
instructions in the application to connect the
appliance.
Reconnecting the Appliance or Connecting
Another User
Press and hold the Wi-Fi button for 3 seconds.
Run the LG ThinQ application and follow the
instructions in the application to connect the
appliance.
Radio Equipment Specifications
FCC Notice
The following notice covers the transmitter
module contained in this product.
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential
installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference to
radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to
try to correct the interference by one or more of
the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment
and the receiver.
Connect the equipment into an outlet on a
circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV
technician for help.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference
and
(2) This device must accept any interference
received, including interference that may cause
undesired operation.
Any changes or modifications in construction of
this device which are not expressly approved by
the party responsible for compliance could void
the user’s authority to operate the equipment.
FCC RF Radiation Exposure
Statement
This equipment complies with FCC radiation
exposure limits set forth for an uncontrolled
environment. This transmitter must not be co-
located or operating in conjunction with any other
antenna or transmitter.
This equipment should be installed and operated
with a minimum distance of 20 cm (7.8 inches)
between the antenna and your body. Users must
follow the specific operating instructions for
satisfying RF exposure compliance.
Industry Canada Statement
This device contains licence-exempt transmitter(s)/
receiver(s) that comply with Innovation, Science
and Economic Development Canada’s licence-
exempt RSS(s). Operation is subject to the
following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference,
including interference that may cause undesired
operation of the device.
IC Radiation Exposure Statement
This equipment complies with IC radiation
exposure limits set forth for an uncontrolled
environment.
Type Frequency
Range
Output
Power
Wi-Fi 2412 MHz - 2462 MHz < 30 dBm
Bluetooth 2402 MHz - 2480 MHz
en-us_main.book.book Page 14 Thursday, November 3, 2022 3:13 PM
15SMART FUNCTIONS
ENGLISH
This equipment should be installed and operated
with a minimum distance of 20 cm (7.8 inches)
between the antenna and your body.
NOTE
THE MANUFACTURER IS NOT RESPONSIBLE FOR
ANY RADIO OR TV INTERFERENCE CAUSED BY
UNAUTHORIZED MODIFICATIONS TO THIS
EQUIPMENT. SUCH MODIFICATIONS COULD
VOID THE USER’S AUTHORITY TO OPERATE THE
EQUIPMENT.
Open Source Software Notice
Information
To obtain the source code that is contained in this
product, under GPL, LGPL, MPL, and other open
source licenses that have the obligation to disclose
source code, and to access all referred license
terms, copyright notices and other relevant
documents, please visit https://
opensource.lge.com.
LG Electronics will also provide open source code
to you on CD-ROM for a charge covering the cost
of performing such distribution (such as the cost of
media, shipping, and handling) upon email
request to open[email protected].
This offer is valid to anyone in receipt of this
information for a period of three years after our
last shipment of this product.
en-us_main.book.book Page 15 Thursday, November 3, 2022 3:13 PM
16 MAINTENANCE
MAINTENANCE
Care and Cleaning
Make sure that the electrical power is off and all
surfaces are cool before cleaning any part of the
cooktop.
Burner Assemblies
Sealed Burner Assemblies
Turn all controls OFF before removing the burner
parts.
The burner grates a, the burner caps b, and the
burner heads c can be lifted off, making them
easy to clean.
The burner electrodes d are not removable.
Dual Extra Large Burner Assembly
The burner head c, the dual burner outer cap b
and the dual burner inner cap a can be lifted off,
making it easy to clean.
The burner electrode d is not removable.
CAUTION
DO NOT remove any parts from the cooktop
until they have completely cooled and are safe to
handle. Do not operate the surface burners
unless all burner parts and grates are properly
assembled.
The electrode of the burner is exposed when the
burner head and cap are removed. When one
burner is turned to LITE, only that burner sparks.
Do not attempt to disassemble or clean around
any burner while another burner is on. An electric
shock may result, which could cause you to knock
over hot cookware.
Burner Caps and Heads
Burner Caps
Lift burner caps off when they are cool.
Wash burner caps in hot, soapy water and rinse
with clean water. You may scour with a plastic
scouring pad to remove burned-on food particles.
To assemble the dual extra large burner outer cap
properly, make sure that the burner cap a is
positioned over the assembly guide b in the
burner head.
General burner
Burner cap is properly
seated.
Burner cap is NOT
properly seated.
Dual Extra Large Burner
outer cap
en-us_main.book.book Page 16 Thursday, November 3, 2022 3:13 PM
17MAINTENANCE
ENGLISH
Burner Heads
The burner heads are removable.
Simply lift them off the cooktop for cleaning.
The slits in the burner heads must be kept clean at
all times for an even flame. Clogged or dirty
burner ports or electrodes may cause improper
operation of the cooktop.
Any spills on or around an electrode must be
carefully cleaned. Take care not to hit an electrode
with anything hard or it could be damaged.
Clean the burner caps and heads routinely,
especially after bad spillovers which could clog the
openings. Lift burner heads off when they are cool.
To get rid of burned-on food, soak the burner
heads in a solution of mild liquid detergent and
hot water for 20–30 minutes. For more stubborn
stains, use a toothbrush.
CAUTION
Do not hit the electrodes with anything hard.
Doing so could damage them.
Do not use steel wool or scouring powders to
clean the burners.
Do not scratch or gouge the port features of the
brass burner base.
It is normal for brass burners to become
tarnished with use.
NOTE
To clean the brass burner, use mild abrasive
cleaners or liquid cleaners.
To clean port openings, use a stiff nylon bristle
toothbrush.
Do not use steel wool or steel bristle brushes as
they can scratch the brass burner surface.
A burner will not light if the cap is removed.
After Cleaning
Before reassembling the burner caps and burner
heads, shake out excess water and then dry them
thoroughly.
Replacement
Replace burner heads and caps over the
electrodes on the cooktop, in the correct locations
according to their size. There are one small, two
medium, one large and one extra large burner
head and cap.
aMedium Burner Head and Cap
bExtra Large Burner (Center) Head and Cap
cSmall Burner Head and Cap
dLarge Burner Head and Cap
Burner Grates
The cooktop has three professional-style grates.
These grates are position-specific. For maximum
stability, these grates should only be used in their
proper position. Because of the varied burner
sizes, the side grates cannot be exchanged nor can
any of the grates be rotated front to back.
Cleaning
Lift grates off when they are cool.
Grates should be cleaned regularly and, of course,
after spills. Wash them in hot, soapy water and
rinse with clean water. When replacing the grates,
be sure they are positioned properly over the
burners.
The grates may be cleaned in a dishwasher.
Do not operate a burner for a long time without
cookware on the grate.
The finish on the grate may chip without cookware
to absorb the heat.
To remove burned-on food, place the grates in a
covered container.
en-us_main.book.book Page 17 Thursday, November 3, 2022 3:13 PM
18 MAINTENANCE
Soak them with 1/4 cup ammonia for several hours
or overnight. Wash, rinse well and dry.
aLeft Grate
bCenter Grate
cRight Grate
Appearance may vary. The grates may be cleaned
in a dishwasher.
Although they are durable, the grates will
gradually lose their shine, regardless of the best
care you can give them. This is due to their
continual exposure to high temperatures. You will
notice this sooner with lighter colored grates.
NOTE
Do not clean the grates in a self-cleaning oven.
Cooktop Surface
To prevent damage to the stainless steel surface of
the cooktop and to prevent it from becoming dull,
clean up spills immediately. Foods with a lot of acid
(such as tomatoes, sauerkraut, fruit juices, etc.) or
foods with high sugar content could cause a dull
spot if allowed to set. When the surface has
cooled, wash and rinse.
For other spills such as fat spatterings, etc., wash
with soap and water after the surface has cooled.
Then rinse and polish using a dry cloth.
CAUTION
To avoid burns, do not clean the cooktop surface
until it has cooled.
Do not lift the cooktop surface. Lifting the
cooktop surface can lead to damage and
improper operation of the range.
NOTE
Do not place flammable materials on or near the
cooktop.
Do not store or use combustible materials,
gasoline or other flammable vapors and liquids
in the vicinity of this or any other appliance.
Do not try to lift the cooktop. Lifting the cooktop
can cause damage and improper operation of
the cooktop.
If water is spilled on the cooktop, wipe it up
immediately. If water is left on the cooktop for a
long time, it may cause discoloration of the
cooktop surface and grate.
The cooktop surface under the burner head may
become discolored if the gas surface burner is
used for a long time.
Stainless Steel Surfaces
Do not use a steel wool pad; it will scratch the
surface.
To clean the stainless steel surface, use warm
soapy water or a stainless steel cleaner or polish.
Always wipe the surface in the direction of the
grain.
Follow the cleaner instructions for cleaning the
stainless steel surface.
To inquire about purchasing stainless steel
appliance cleaner or polish, or to find the location
of the nearest dealer, call the toll-free customer
service number: 1-800-243-0000 (USA), 1-888-542-
2623 (CANADA) or visit our website at: http://
www.lg.com
Control Knobs
It’s a good idea to wipe the control panel after
each use of the cooktop.
Use mild soap and water or a 50/50 solution of
vinegar and water. Use clean water for rinsing.
Clean or rinse the control panel using a damp
cloth. Use mild soap and water or a 50/50 solution
of vinegar and water. Use clean water for rinsing.
Do not use abrasive cleansers, strong liquid
cleaners, plastic scouring pads or oven cleaners on
en-us_main.book.book Page 18 Thursday, November 3, 2022 3:13 PM
19MAINTENANCE
ENGLISH
the control knobs. They can cause damage to the
finish of the knobs.
Do not try to bend knobs by pulling them up or
down or by hanging a towel or other such loads.
This can damage the gas valve shaft.
The control knobs may be removed for easier
cleaning.
Make sure the knobs are in the OFF position and
pull them straight off the stems for cleaning.
aSurface Burner Knob
To reinstall a knob, hold it with the OFF label at the
top and slide it directly onto the stem.
NOTE
Unplug the cooktop before cleaning the control
knobs to prevent the burners from turning on.
en-us_main.book.book Page 19 Thursday, November 3, 2022 3:13 PM
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93

LG CBGJ3027 Gas Cooktop Le manuel du propriétaire

Catégorie
Cuisinières
Taper
Le manuel du propriétaire