Kichler 300032 54 Inch 3 Blade Indoor LED Ceiling Fan Manuel utilisateur

INSTRUCTION MANUAL

Model# 300032, 300154

Product images may vary slightly from actual product.

48”/ 54” Volos LED

READ AND SAVE THESE INSTRUCTIONS

2 | KICHLER.COM

TABLE OF CONTENTS

SAFETY RULES ..................................................................3

TOOLS REQUIRED ...........................................................5

PACKAGE CONTENTS ...................................................5

MOUNTING OPTIONS ....................................................6

HANGING THE MOTOR ASSEMBLY ......................... 7

INSTALLATION OF SAFETY CABLE ..........................8

ELECTRICAL CONNECTIONS ................................... 9

WIRE DIAGRAM ...............................................................10

FINISHING THE MOTOR INSTALLATION ............. 11

INSTALLING THE MOTOR HOUSING ....................12

ATTACHING THE FAN BLADES .................................13

INSTALLING THE LED LIGHT KIT ASSEMBLY ....13

INSTALLING THE WALL CONTROL .........................14

OPERATING INSTRUCTION ........................................15

TROUBLESHOOTING....................................................17

FCC INFORMATION .......................................................18

48”/ 54” Volos LED | 3

SAFETY RULES

CAUTION – RISK OF SHOCK – Disconnect Power at

the main circuit breaker panel or main fusebox before

starting and during the installation.

WARNING: All wiring must be in accordance with the

National Electrical Code “ANSI/NFPA 70” and local

electrical codes. Electrical installation should be

performed by a qualified licensed electrician.

WARNING: To reduce the risk of electric shock, this fan

must be installed with a general-use, isolating wall

control/switch.

WARNING: Not suitable for use with solid-state speed

controls.

WARNING: To reduce the risk of fire, electric shock, or

personal injury, mount to outlet box marked

“acceptable for fan support of 15.9 kg (35 lbs.) or less”

and use mounting screws provided with the outlet box.

Most outlet boxes commonly used for the support of

light fixtures are not acceptable for fan support and

may need to be replaced. Due to the complexity of the

1.

2.

3.

4.

5.

installation of this fan, a qualified licensed electrician is

strongly recommended.

The outlet box and support structure must be securely

mounted and capable of reliably supporting a minimum

of 15.9 kg (35 pounds). Use only cULus Listed outlet

boxes marked “Acceptable for Fan Support of 15.9 kg

(35 lbs) or less”.

The fan must be mounted with a minimum of 2.1 m

(7 feet) clearance from the trailing edge of the blades

to the floor.

To operate the reverse function on this fan, press the

reverse button while the fan is running.

Avoid placing objects in the path of the blades.

WARNING: make sure the power is disconnected

before cleaning your fan.

To avoid personal injury or damage to the fan and

other items, be cautious when working around or

cleaning the fan.

6.

7.

8.

9.

10.

11.

4 | KICHLER.COM

WARNING

TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND

THE BLADE DURING ASSEMBLY OR AFTER INSTALLATION.

DO NOT

INSERT OBJECTS IN THE PATH OF THE BLADES.

SAFETY RULES

Do not use water or detergents when cleaning the fan

or fan blades. A dry dust cloth or lightly dampened

cloth will be suitable for most cleaning.

After making electrical connections, spliced

conductors should be turned upward and pushed

carefully up into outlet box. The wires should be spread

apart with the grounded conductor and the

equipment-grounding conductor on one side of the

outlet box and the ungrounded conductor on the other

side of the outlet box.

Electrical diagrams are reference only. Light kits that

are not packed with the fan must be cULus Listed and

marked suitable for use with the model fan you are

installing. Switches must be cULus General Use

Switches. Refer to the Instructions packaged with the

light kits and switches for proper assembly.

All set screws must be checked, and retightened where

necessary, before installation.

12.

13.

14.

15.

The subject fan weight information is as below:

16.

Model

300032

300154

Net Weight

(kgs)

Gross Weight

(kgs)

Net Weight

(lbs)

Gross Weight

(lbs)

6.9 7.7 15.216.9

7.3 8.4 16.06 18.48

TOOLS REQUIRED

PACKAGE CONTENTS

Phillips screwdriver

Blade screwdriver

11 mm wrench

Step ladder

Wire cutters

Unpack your fan and check the contents . You should have the following items:

A. Mounting Plate

B. Motor Assembly

C. Motor Housing

D. LED Light Kit Assembly

E. Blade (3)

F. Wall Control System

Receiver (1)

Wire connector (6)

Wall Control (1)

Wire connector (4)

Screw ( 2)

G. Package hardware

1.) Mounting hardware:

Wire Connector (3)

2.) Blade attachment hardware:

Screw (9)

3.) Safety cable hardware:

Wood screw (1),

Spring washer (1)

Flat washer (1)

A

B

C

D

GF

E

48”/ 54” Volos LED | 5

6 | KICHLER.COM

MOUNTING OPTIONS

If there isn’t an existing UL (cUL for Canadian Installation) listed mounting box,

then read the following instructions. Disconnect the power by removing fuses

or turning o circuit breakers.

Secure the outlet box directly to the building structure. Use appropriate

fasteners and building materials. The outlet box and its support must be able

to fully support the full weight of the fan (up to 15.9 kg (35 pounds)). Do not use

plastic outlet boxes.

Figures 1 and 2 are examples of dierent ways to mount the outlet box.

NOTE: Depending on the location you have selected for installation, you may

need to purchase and install a “Joist Hanger” for the support of the outlet box.

Make sure the joist hanger you purchase has been designed for use with ceiling

fans. (Fig. 3)

Fig. 1

Outlet box

Fig. 2

Fig. 3

Outlet box

Fig. 4

Fig.5

HANGING THE MOTOR ASSEMBLY

REMEMBER to turn off the power before you begin installation.

This is necessary for your safety and also the proper programming

of the control system.

To properly install your ceiling fan, follow the steps below.

Step 1. Before attaching fan to outlet box (not included), ensure the

outlet box is securely fastened to at least two points to a structural

ceiling member (a loose box will cause the fan to wobble). Pass the

120 volt supply wires from the outlet box through the center of the

mounting plate. Install mounting plate to outlet box in ceiling using the

screws and washers included with the outlet box. (Fig. 4)

Step 2. Hook the motor assembly onto the mounting plate as shown.

You can now proceed with the electrical wiring of your fan. (Fig.5)

Outlet Box

Screw

Washer

Motor

Assembly

Mounting Plate

48”/ 54” Volos LED | 7

8 | KICHLER.COM

Flat Washer

INSTALLATION OF SAFETY SUPPORT

(required for Canadian installation ONLY)

A safety support cable is provided to help prevent the ceiling fan from faIling, please

install it as follows.

Step 1. Drive a wood screw and washers into the side of the brace that holds the outlet

box. Leave 3mm (1/8") of space between the support brace and the washer. (Fig. 6)

Step 2. Insert the safety cable through the mounting bracket and one of the holes in

the outlet box into the ceiling. Adjust the length of the safety cable to reach the screw

and washers by pulling the extra cable through the cable clamp until the overall length is

correct, put the end of the cable back through the cable clamp, forming a loop at the end

of the cable. Tighten the cable clamp securely. Now, put the loop in the end of the safety

cable over the wood screw and under the washer. Tighten the wood screw securely.

(Fig.7)

NOTE: Although the safety support cable is required for Canadian installations only.

It’s a good idea to make the attachment with any installation.

Wood Screw

Spring Washer

Outlet Box

Ceiling

Support Brace

Safety Cable Bolt

Wood Screw

Fig. 6

Fig. 7

ELECTRICAL CONNECTIONS

WARNING: To avoid possible electrical shock, be sure you have turned off the power at the main circuit panel before wiring.

Follow the steps below to connect the fan to your household wiring. Use the wire connectors supplied with your fan. Secure the

connector with electrical tape. Make sure there are no loose wire stands or connections.

WARNING: If your house wires are different colors than referenced in this manual, stop immediately.

A professional electrician is recommended to determine proper wiring.

Step 1. Place the receiver into the mounting plate cover and keep flat in opposition of ceiling. (Fig. 8)

Step 2. Motor to Receiver Electrical Connections:

Connect the WHITE wire from the fan to WHITE wire marked “TO MOTOR N” from the receiver. Connect

the BLACK wire from the fan to BLACK wire marked “TO MOTOR L” from the receiver. Connect the

BLUE wire from the fan to BLUE wire marked “FOR LIGHT” from the receiver.

Step 3. Receiver to Household Electrical Connections:

Connect the WHITE wire marked “AC IN N” from the receiver to the WHITE wire from the house. Connect

the BLACK wire marked “AC IN L” from the receiver to the BLACK wire marked “TO MOTOR L” from the

wall control.

Connect the BLACK wire marked “AC IN L” from the wall control to the BLACK wire from the house.

Step 4. Ground wires connections:

Connect the GROUND wire from the house to the GREEN wires from the motor assembly and mounting plate.

Step 5. Secure all wires connections with the plastic wire connectors provided. (Fig. 9 )

NOTE: After connecting the wires, spread them apart so that the green and white wires are on one side of the outlet box and black and

blue wire and on the other side. Carefully tuck the wire connections up into the outlet box.

NOTE: Fan must be installed at a maximum distance of 30 feet from the transmitting unit for proper signal transmission between the

transmitting unit and the fan’s receiving unit.

Fig. 8

Receiver

Mounting

Plate Cover

48”/ 54” Volos LED | 9

10 | KICHLER.COM

WIRE DIAGRAM

Fig. 9

BLACK (MOTOR)

WHITE (NEUTRAL)

BLACK

("TO MOTOR L")

BLACK

("AC IN L")

BLACK

WALL

CONTROL

GROUND WIRE

AC 120V INPUT

GROUND WIRE

BLUE(FOR LIGHT)

BLACK ("TO MOTOR L")

WHITE("TO MOTOR N")

BLUE(FOR LIGHT)

BLACK("AC IN L")

WHITE("AC IN N")

RECEIVER

BLACK

WHITE

GROUND WIRE

FROM CEILING

Fig. 10

Fig. 11

FINISHING THE MOTOR INSTALLATION

CAUTION: Before continuing, make sure the power is disconnected by

turning off the circuit breaker or removing the fuse at the circuit box.

Step 1. Remove one of the three screws from the mounting plate and keep for

later use. Loosen the other two (do not remove). (Fig.10 )

Step 2. Release the motor assembly from the J hook, raise the motor

assembly up to the mounting plate, align the slot holes on the mounting plate

cover with two loosen screws on the mounting plate. Rotate the mounting

plate cover until two loosened screws lock in place at the narrow end of key

holes. Re-install the screw removed on step 1, tighten three screws securely.

(Fig. 11)

Mounting Plate

Mounting Plate Cover

48”/ 54” Volos LED | 11

12 | KICHLER.COM

Fig. 12a Fig. 12b

INSTALLING THE MOTOR HOUSING

Step 1. Place motor housing up to the mounting plate cover,

attach three hang tags with screws on the motor housing to the

key holes on the mounting plate cover. (Fig. 12a)

Step 2. Twist the motor housing clockwise until three screws lock

at the end of the slotted holes. (Fig. 12b)

WARNING: Ensure you complete above steps correctly and

follow all steps. Failure to do that might cause the fan to fall.

Mounting

Plate Cover

Motor

Housing

Fig. 13

Fig. 14

ATTACHING THE FAN BLADES

CAUTION: To Reduce The Risk Of Electric Shock, Disconnect The Electrical

Supply Circuit To The Fan Before Installing Fan Blades.

Step 1. Attach the fan blades to the flywheel using the blade screws and tighten

them securely. (Fig.13)

INSTALLING THE LED LIGHT KIT ASSEMBLY

CAUTION: Before continuing installation, confirm that the power is still

turned off at the main circuit breaker or by removing the circuit fuse. Turning

the power off using a wall switch is not sufficient to prevent electrical shock.

Step 1. Hold the LED light kit assembly close the motor and connect the pin

connectors together. (Fig. 14)

NOTE: The connectors have keyholes that must be mated correctly before

they can be engaged.

Step 2. Tuck the connections neatly into the LED light kit assembly, raise the

LED light kit assembly up to the motor, align the red dot labels, and twist screws

on top of LED light kit toward the narrow end of the slotted holes on the motor

as shown. Make sure all screws lock in place and LED light kit no longer turns.

(Fig. 14)

Blade

Blade Screw

LED Light Kit Assembly

48”/ 54” Volos LED | 13

14 | KICHLER.COM

Outlet Box Switch

Outlet Box

HOT

TO 120V SOURCE

GROUND WIRE

FROM CEILING

TO LOA D

BLACK

(“AC IN L”)

GROUND

BLACK

(“TO MOTOR L”)

Wall Control

Face Plate

Wall Plate

Fig. 15

Fig. 16

INSTALLING THE WALL CONTROL

WARNING: All wiring must be in accordance with the National Electrical Code

and local electrical codes. Electrical installation should be performed by a

qualified licensed electrician.

NOTE: SWITCH INSTALLATION MUST COMPLY WITH ALL LOCAL AND

NATIONAL ELECTRIC CODE.

WARNING: Shut off main power at the circuit breaker or fuse panel before

continuing.

Step 1. Remove the existing wall plate and the old switch from the wall outlet box.

Disconnect wires. (Fig. 15)

Step 2. Place the wall control to the outlet box, connect the wires with wire

connectors provided. (Fig. 16)

*Connect the lead wire (HOT) from the outlet box to BLACK wire marked

“AC IN L” from wall control.

*Connect the lead wire (LOAD) from the outlet box to BLACK wire marked

“TO MOTOR L” from wall control.

*Connect the GROUND from the outlet box to GROUND from wall control.

Step 3. Secure the wires connectors and make sure there are no loose strands or

connections. Carefully tuck wire connections back inside outlet box and secure the

wall control to outlet box with screws provided. Snug the face plate to wall control.

OPERATING INSTRUCTION

ACTIVATING THE LEARNING PROCESS

NOTE: The control system for this fan is equipped with a learning frequency function which has 56K

code combinations to prevent potential interference from other remote units. The frequency on your

receiver and wall control units has been preset at the factory. No frequency change is necessary. If

the fan is non-functional or if you desire to install another fan within the same area with a separate

frequency code, refer to “ learning process” section of this instruction manual to code-paring the

receiver and wall control.

1.Use a small flat screw driver and gently pry the faceplate apart from the top of wall control. (Fig. 17)

2.After installation is complete, press and hold the LEARN button for 3 seconds within 30 seconds

after AC power is turned on. Fan will turn on at medium speed and light (if installed) will turn on. This

confirms that the SMART SYNC setting is active and OK.

3.If you cannot finish the setting within the 30 seconds time frame, the main power must be turned

o and re-started again. This will repeat step 1 until the LEARN feature is activated as indicated.

LIGHT FUNCTION SELECT SWITCH(Fig. 18)

D means “Dimmer”

O means “only on/o, no dimmer”

The light of this fan is dimmable, it has been set to “D” position at factory. If you want the light to be

only ON/OFF, slide the switch to “O” position.

WALL CONTROL OPERATION(Fig. 18)

ON/OFF: Active and lock the wall control

HI : High speed

MED: Medium speed

LOW: Low speed

FAN OFF: Turn o the fan

LIGHT: Turn light ON or OFF. Press and hold the button to set desired brightness.

REV: Control direction, forward or reverse.

LEARN

Light function select switch

Faceplate

Fig. 17

Fig. 18

48”/ 54” Volos LED | 15

16 | KICHLER.COM

Fig.19

Fig. 20

REVERSE FUNCTION

NOTE: To operate the reverse function on this fan, press the reverse button while

the fan is running.

Warm Weather Operation: Forward (counter clockwise). A downward airflow

creates a cooling effect (Fig. 19). This allows you to set your air conditioner on a

warmer setting without affecting your general comfort.

Cool Weather Operation: Reverse (clockwise). An upward airflow moves warm air

off the ceiling areas (Fig. 20). This allows you to set your heating unit on a cooler

setting without affecting your general comfort.

TROUBLESHOOTING

Problem

Fan will not start.

Fan sounds noisy.

Fan wobble.

Remote control

malfunction.

Solution

1. Check circuit fuses or breakers.

2. Check all electrical connections to ensure proper contact. CAUTION: Make sure the main power is OFF

when checking any electrical connection.

1. Make sure all motor housing screws are snug.

2. Make sure the screws that attach the fan blade brackets to the motor are tight.

3. Make sure wire nut connections are not rubbing against each other or the interior wall of the switch housing.

CAUTION: Make sure main power is off.

4. Allow a 24-hour "breaking-in" period. Most noise associated with a new fan disappears during this time.

5. If using an optional light kit, make sure the screws securing the glassware are tight. Make sure the light bulbs are

not touching any other component.

6. Do not connect this fan to a wall mounted variable speed control(s). They are not compatible with ceiling fan motors

or remote controls.

7. Make sure the upper canopy has a short distance from the ceiling. It should not touch the ceiling.

1. Check that all blade and blade arm screws are secure.

2. Most fan wobbling problems are caused when blade levels are unequal. Check this level by selecting a point on the

ceiling above the tip of one of the blades. Measure this distance. Rotate the fan until the next blade is positioned for

measurement. Repeat for each blade. The distance deviation should be equal within 1/8".

3. If the blade wobble is still noticeable, interchanging two adjacent (side by side) blades can redistribute the weight

and possibly result in smoother operation.

1.Ceiling Fans with remote control systems CAN NOT be operated in conjunction with any other control system

EXCEPT a basic On/off wall switch, if desired.

48”/ 54” Volos LED | 17

18 | KICHLER.COM

FCC Information

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1.)This device may not cause harmful interference, and

2.)This device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by

turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician or help.

www.kichler.com

KICHLER LIGHTING LLC

30455 Solon Rd.

Solon, OH 44139 USA

CUSTOMER SERVICE 866.558.5706

8:00 AM TO 5:00 PM EST, MONDAY - FRIDAY

2022/7/27

MANUEL D'INSTRUCTIONS

Nº de modèle :300032, 300154

Les images du produit peuvent varier légèrement par rapport au produit réel.

DEL Volos de 48 po / 54 po

LIRE ET CONSERVER CES INSTRUCTIONS

La page charge ...

Kichler 300032 54 Inch 3 Blade Indoor LED Ceiling Fan Manuel utilisateur

Kichler 300032 54 Inch 3 Blade Indoor LED Ceiling Fan Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents