Maytag Gemini MER6765BAS Mode d'emploi

Marque: Maytag

Modèle: Gemini MER6765BAS

Catégorie: Cuisinières

Taper: Mode d'emploi

Ce manuel convient également à

?VlA A(]

Maytag Electric Smoothtop

Double Oven Range

Precision Touch 750 Series

Tabl

Safety .......................................... 1-3

Surface Cooking ...................... 4=7

Warming Center

Controls

Smoothtop Surface

Oven Cooking ......................... 8=17

Control _anel

Baking

Cook & Hold

Delay

Keep Warm

Toasting

Broiling

Oven Racks

Care & Cleaning ................... 18=21

Self-Clean Oven

Cleaning Procedures

Maintenance ......................... 22=23

Oven Doors and Windows

Oven Lights

Troubleshooting ................... 24-25

_ Warranty & Service .................... 27

Guide d'utilisation et

d'entretien ................................... 28

Guia de use y cuidado .............. 56

General instructions

To ensure proper and safe operation: Appliance must

be properly installed and grounded by a qualified

technician. Do not attempt to adjust, repair, service, or

replace any part of your appliance unless it is specifically

recommended in this guide. All other servicing should be

referred to a qualified servicer.

Always disconnect power to appliance before servicing.

ImportentSefety

Instructions

Warning and Important Safety Instructions appearing in

this guide are not meant to cover all possible conditions

and situations that may occur. Common sense, caution,

and care must be exercised when installing, maintaining,

or operating the appliance.

Always contact your dealer, distributor, service agent, or

manufacturer about problems or conditions you do not

understand.

Recognize Safety Symbols, Words, Labels

To check if device is properly installed, look underneath

range with a flashlight to make sure one of the rear

leveling legs is properly engaged in the bracket slot. The

anti-tip device secures the rear leveling leg to the floor

when properly engaged. You should check this anytime

the range has been moved.

in Case of Fire

Turn off appliance and ventilating hood to avoid spreading

the flame. Extinguish flame, then turn on hood to remove

smoke and odor.

• Cooktop: Smother fire or flame in a pan with a lid or

cookie sheet.

NEVER pick up or move a flaming pan.

* Ovens: Smother fire or flame by closing the oven doors.

Do not use water on grease fires. Use baking soda, a dry

chemical or foam-type extinguisher to smother fire or

flame.

Read and follow all instructions before using this

appliance to prevent the potential risk of fire, electric

shock, personal injury or damage to the appliance as a

result of improper usage of the appliance. Use appliance

only for its intended purpose as described in this guide.

Impona,tSuretyinstructions

If appliance is installed near a window, precautions should

be taken to prevent curtains from blowing over surface

elements.

NEVER use appliance to warm or heat the room. Failure to

follow this instruction can lead to possible burns, injury, fire,

or damage to the appliance.

NEVER wear loose-fitting or hanging garments while using

the appliance. Clothing could catch utensil handles or ignite

and cause burns if garment comes in contact with hot

heating elements.

To ensure proper operation and to avoid damage to the

appliance or possible injury, do not adjust, service, repair or

replace any part of the appliance unless specifically

recommended in this guide. Refer all other servicing to a

qualified technician.

NEVER store or use gasoline or other combustible or

flammable materials in the ovens, near surface units or in the

vicinity of this appliance as fumes could create a fire hazard

or an explosion.

To prevent grease fires, do not let cooking grease or other

flammable materials accumulate in or near the appliance.

Use only dry potholders. Moist or damp potholders on hot

surfaces may result in a steam burn. Do not let potholders

touch hot heating elements. Do not use a towel or other

bulky cloth which could easily touch hot heating elements

and ignite.

Aiwaysturn off all controls when cooking is completed.

NEVER heat unopened containers on the surface unit or in

the ovens. Pressure build-up in the container may cause

container to burst resulting in burns, injury or damage to the

appliance.

NEVER use aluminum foil to line drip bowls or cover oven

racks or oven bottoms. This could result in risk of electric

shock, fire, or damage to the appliance. Use foil only as

directed in this guide.

Aerosol-type cans are EXPLOSIVEwhen exposed to heat

and may be highly flammable. Do not use or store near

appliance.

Cooktop

NEVER leave surface units unattended, especially when

using high heat. An unattended boilover could cause

smoking and a greasy spillover can cause a fire.

This appliance is equipped with different sized surface

elements. Select pans with flat bottoms large enough to cover

element. Fitting pan size to element will improve cooking

efficiency.

If pan issmaller than element, a portion of the element will

be exposed to direct contact and could ignite clothing or

potholder.

Only certain types of glass, glass-ceramic, ceramic,

earthenware, or other glazed utensils are suitable for

cooktop or oven service without breaking due to the sudden

change in temperature. Follow utensil manufacturer's

instructions when using glass.

This appliance has been tested for safe performance using

conventional cookware. Do not use any devices or

accessories that are not specifically recommended in this

manual. Do not use stove top grills or add-on oven

convection systems. The use of devices or accessories that

are not expressly recommended in this manual can create

serious safety hazards, result in performance problems, and

reduce the life of the components of this appliance.

Turn pan handle toward center of cooktop, not out into the

room or over another surface element. This reduces the risk

of burns, ignition of flammable materials, or spillage if pan is

accidently bumped or reached by small children.

Glass-Ceramic Cooktop

NEVER cook on broken cooktop. If cooktop should break,

cleaning solutions and spillovers may penetrate the broken

cooktop and create a risk of electric shock. Contact a

qualified technician immediately.

Clean cooktop with caution. Some cleaners can produce

noxious fumes if applied to a hot surface. If a wet sponge,

cloth, or paper towel is used on a hot cooking area, be

careful to avoid steam burn.

Heating Elements

NEVER touch surface or oven heating elements, areas near

elements, or interior surfaces of ovens.

Heating elements may be hot even though they are dark in

color. Areas near surface elements and interior surfaces of

the ovens may become hot enough to cause burns. During

and after use, do not touch or let clothing or other

flammable materials contact heating elements, areas near

elements, or interior surfaces of ovens until they have had

sufficient time to cool.

Other potentially hot surfaces include: Cooktop, areas

facing the cooktop, oven vent, and surfaces near the vent

opening, oven doors, areas around the doors and oven

windows.

importantSurety

Deep Fat Fryers

Use extreme caution when moving the grease pan or

disposing of hot grease. Allow grease to cool before

attempting to move pan.

Ovens

Use care when opening doors. Let hot air or steam escape

before removing or replacing food.

For proper oven operation and performance, do not block

or obstruct oven vent duct. When ovens are in use, the vent

and surrounding area near the vent may become hot

enough to cause burns.

A/ways place oven racks in desired locations while ovens

are cool. If rack must be moved while an oven is hot, do

not let potholder contact hot element in oven.

Self-Cleaning Ovens

Clean only parts listed in this guide. Do not clean door

gasket. The gasket is essential for a good seal. Do not rub,

damage, or move the gasket.

Do not use oven cleaners. No commercial oven cleaner or

oven liner protective coating of any kind should be used in or

around any part of the ovens.

Wipe up excessive spillovers, especially greasy spills, before

the clean cycle to prevent smoking, flare-ups or flaming.

It is normal for the cooktop to become hot during a clean

cycle. Therefore, avoid touching the cooktop, door, window or

oven vent during a clean cycle.

Child Safety

NEVER leave children alone or unsupervised in area where

appliance is in use or is still hot.

NEVER allow children to sit or stand on any part of the

appliance as they could be injured or burned.

Children must be taught that the appliance and utensils in

or on it can be hot. Let hot utensils cool in a safe place, out

of reach of small children. Children should be taught that an

appliance is not a toy. Children should not be allowed to

play with controls or other parts of the unit.

Ventilating Hoods

Clean range hood and filters frequently to prevent grease or

other flammable materials from accumulating on hood or

filter and to avoid grease fires.

Turn the fan on when flambeing foods (such as Cherries

Jubilee) under the hood.

important Safety Notice

and Warning

The California Safe Drinking Water and Toxic

Enforcement Act of 1986 (Proposition 65) requires the

Governor of California to publish a list of substances

known to the State of California to cause cancer or

reproductive harm, and requires businesses to warn

customers of potential exposures to such substances.

Users of this appliance are hereby warned that when the

oven is engaged in the self-clean cycle, there may be

some low-level exposure to some of the listed

substances, including carbon monoxide. Exposure to

these substances can be minimized by properly venting

the oven to the outdoors by opening the windows and/or

door in the room where the appliance is located during

the self-clean cycle.

IMPORTANT NOTICE REGARDING PET BIRDS: Never

keep pet birds in the kitchen or in rooms where the

fumes from the kitchen could reach. Birds have a very

sensitive respiratory system. Fumes released during an

oven self-cleaning cycle may be harmful or fatal to birds.

Fumes released due to overheated cooking oil, fat,

margarine and overheated non-stick cookware may be

equally harmful.

Save These instructions for

Future Reference

¢00ktn

Surface Controls

Use to turn on the surface elements. An infinite choice of

heat settings is available from Low to High. The knobs can

be set on or between any of the settings.

Setting the Controls

1. Place pan on surface element.

2. Push in and turn the knob in either direction to the desired

heat setting.

+ The control panel is marked to identify which O O

element the knob controls. For example, the _.O_

graphic at right indicates left front element.

3. There is an element "ON" indicator light on the control

panel. When any surface control knob is turned on, the

light will turn on. The light will turn off when all the

surface elements are turned off.

4. After cooking, turn knob to OFF. Remove pan.

Dual Elements ([selectmodels)

The cooking surface has two dual elements

located in the right front and left front of

the smoothtop. This allows you to change

the size of these elements. Turn control

knob to OFF before switching element

size.

Press the switch to the left to use the

large element or to the right to use the

small element.

Low

Triple Element (select models)

The cooking surface has one triple

element located in the right front position.

This element can be used for larger o

cooking utensils when the triple element

ischosen, or for smaller pans when the

single or dual settings are chosen. To +

operate the single element, push in the

control knob and rotate to the left. To lo

operate the dual or triple elements, make

the selection with the rocker switch and rotate

the control knob to the right.

OFF

Low 2

Suggested Heat Settings

The size,type of cookware and cooking operation will affect

the heat setting. For information on cookware and other

factors affecting heat settings, refer to Cookware

Recommendations on page 7.

Warm _right or left rear elemen0: Food maintains a tempera-

ture above 140° Fwithout continuing to cook. Food is heated

on a higher setting until it reaches this temperature. Never

use a hold or warm setting to reheat cold food. Be sure knob

isadjusted to produce a consistant temperature.

Simmer: Foodforms bubbles that barely break the surface.

Foods are between 185° Fand 200° F.A simmer setting can

also be used to steam or poach foods or continue cooking

covered foods. (Adjust the knob between High and Low to

obtain the desired simmer actiony

Slow Boil: Food forms bubbles at a moderate pace. A slow

boil setting can also be used for most frying and for

maintaining the cooking of large amounts of liquids. (Adjust

SuffuceCooktn

the knob between High and Low to obtain the desired boil

action.)

Boil: Liquid forms bubbles at a rapid pace. A fast boil setting

can be used to bring liquid to a boil, brown meat, stir fry,

saute, and heat oil for frying before turning to a lower setting.

The High setting is always used to bring liquids to a boil.

Once the liquid boils, always turn the control to the lowest

setting that will maintain the boil action.

Flex-Choice TMElement (select models:)

The Flex-ChoiceTM element is a fully OFF

Melt

functioning element that provides an

ultra low Melt heat setting for melting

chocolate and butter. It is located in

the left rear position

The Melt setting is located between s_m

2 and OFF.Heat settings outside of this

area function as a normal element, with

2 (Low) to High settings.

Mediurn

Note: When using the normal settings for preparing foods,

it may take a few minutes for the cooking area to cool to

the Melt heat setting.

Srnoothtop Surface

Notes:

For Canadian models, the smoothtop does NOT operate

during a clean cycle.

Cooktop may emit light smoke and odor the first few

times the cooktop is used. This isnormal.

Smoothtop cooktops retain heat for a period of time

after the element is turned off. Turn the elements off

a few minutes before food iscompletely cooked and use

the retained heat to complete cooking. When the Hot

Surface indicator light turns off, the cooking area will be

cool enough to touch. Because of the way they retain

heat, the smoothtop elements will not respond to

changes in settings as quickly as coil elements.

In the event of a potential believer, remove the pan from

the cooking surface.

Never attempt to lift the cooktop.

The smoothtop surface may appear discolored when it is

hot. This is normal and will disappear when the surface

cools.

Cooking Areas

The cooking areas on your range are identifiedby permanent

circles on the smoothtop surface. For most efficient cooking,

fit the pan size to the element size.

Pans should not extend mere than _/2to 1-inch beyond

the cooking area.

When a control isturned on, a glow can be seen through the

smoothtop surface. The element will cycle on and off to

maintain the preset heat setting, even on High.

For more information on cookware refer to Cookware

Recommendations on page 7.

SINGLE ELEMENT WARMING CENTER

(WITH FLEX-CHOICE rM ;)

OPTION)

DUAL ELEMENT/

(SELECT MODELS)

(style varies by model)

SINGLE ELEMENT

(WITH FLEX-CHOICE _M

OPTION)

TRIPLE ELEMENT

(SELECT MODELS)

* Flex-ChoiceTM:This setting uses a very low heat

setting to keep delicate foods or foods in a covered pan

warm without cooking.

Hot Surface Light

The Hot Surface indicator light is located on the

control panel. The light will be illuminated

He_ Surface

when any cooking area ishot. It will remain on,

even after the control is turned off, until the area has cooled.

Su uceCooktn

Warming Center (select models) OFF

Use the Warming Center to keep hot cooked foods

warm, such as vegetables, gravies and oven-safe

dinner plates.

Setting the Control:

Press switch up to turn off or down to activate. ON

Important:

• Never warm food for longer than one hour (eggs for 30

minutes1, as food quality may deteriorate.

° Do not heat cold food on the Warming Center.

° Warming temperatures of the food will vary depending on

type and amount of food. Always hold food at proper food

temperatures. USDA recommends food temperatures

between 140°-170° F.

Notes:

Use only cookware and dishes recommended as safe for

oven and cooktop use.

Always use oven mitts when removing food from the

Warming Center as cookware and plates will be hot.

All foods should be covered with a lid or aluminum foil to

maintain food quality.

When warming pastries and breads the cover should have

an opening to allow moisture to escape.

Do not use plastic wrap to cover foods. Plastic may melt

on to the surface and be very difficult to clean.

Tips to Protect the

Smoothtop Surface

Cleaning (see page 20 for more information1

° Before first use, clean the cooktop.

° Clean your cooktop daily or after each use. This will keep

your cooktop looking good and can prevent damage.

• If a spillover occurs while cooking, immediately clean the

spill from the cooking area while it is hot to prevent a tough

cleaning chore later. Using extreme care, wipe spill with a

clean dry towel.

° De not allow spills to remain on the cooking area or the

cooktop trim for a long period of time.

• Never use abrasive cleansing powders or scouring pads

which will scratch the cooktop.

° Never use chlorine bleach, ammonia or other cleansers not

specifically recommended for use on glass-ceramic.

To Prevent Marks & Scratches

° Do not use glass pans. They may scratch the surface.

° Never place a trivet or wok ring between the surface and

pan. These items can mark or etch the top.

• Do not slide aluminum pans across a hot surface. The pans

may leave marks which need to be removed promptly. (See

Cleaning, page 20.1

• Make sure the surface and the pan bottom are clean before

turning on to prevent scratches.

° To prevent scratching or damage to the glass-ceramic top,

do not leave sugar, salt or fats on the cooking area. Wipe

the cooktop surface with a clean cloth or paper towel

before using.

° Never slide heavy metal pans across the surface since

these may scratch.

To Prevent Stains

• Never use a soiled dish cloth or sponge to clean the

cooktop surface. A film will remain which may cause stains

on the cooking surface after the area is heated.

• Continuously cooking on a soiled surface may/will result in

a permanent stain.

To Prevent Other Damage

• Do not allow plastic, sugar or foods with high sugar

content to melt onto the hot cooktop. Should this happen,

clean immediately. (See Cleaning, page 20.1

• Never let a pan boil dry as this will damage the surface and

pan.

° Never use cooktop as awork surface or cutting board.

• Never cook food directly on the surface.

• Do not use a small pan on a large element. Not only does

this waste energy, but itcan also result in spillovers burning

onto the cooking area which requires extra cleaning.

• Do not use non-fiat specialty itemsthat are oversized or

uneven such as round bottom woks, rippled bottom and/or

oversized canners and griddles.

° Do not use foil or foil-type containers. Foil may melt onto

the glass. If metal melts on the cooktop, do not use. Call an

authorized Maytag Servicer.

¢ooktn

Cookware Recommendations

Using the right cookware can prevent many problems, such

as food taking longer to cook or achieving inconsistent

results. Proper pans will reduce cooking times, use less

energy, and cook food more evenly.

Flat Pan Tests

See if your pans are flat.

The Ruler Test:

1. Place a ruler across the bottom of the pan.

2. Hold it up to the light.

3. Little or no light should be visible under the ruler.

The Bubble Test:

1. Put I inchof water in the pan. Place on cooktop and turn

control to High.

2. Watch the formation of the bubbles as the water heats.

Uniform bubbles mean good performance, and uneven

bubbles indicate hot spots and uneven cooking.

Flat,smooth-bottom Panswith grooved or warped bottoms.

)ans. Panswith uneven bottoms do not cook

efficiently and sometimes may not

boil liquid.

Heavy-gauge pans. Very thin-gauge metal or glass pans.

Pansthat are the Panssmaller or larger than the

same size as the element by 1 inch.

element.

Secure handles. Cookware with loose or broken handles.

Heavyhandles that tilt the pan.

Tight-fitting lids. Loose-fitting lids.

Flat bottom woks. Woks with a ring-stand bottom.

Canning and Oversize

Cookware

All canners and large pats must have flat battams and

must be made fram heavy=gauge materials. This iscritical

on smoothtop surfaces. The base must not be more than

1 inch larger than the element.

When canners and pots do not meet these standards, cooking

times may be longer, and cooktops may be damaged.

Some canners are designed with smaller bases for use on

smoothtop surfaces.

When canning, use the High heat setting anly until the

water comes taa boil or pressure isreached in the canner.

Reduce to the lowest heat setting that maintains the boil or

pressure. If the heat isnot turned down, the cooktop may be

damaged.

Control Panel

A B C D E

......................... Clean:

,/ Bake Toast

' Keep

"\\\\

Clean) "---_

....Veen,. _,

F G H I J K L

Thecontrol panel isdesigned for easeinprogramming. Thedisplaywindow on thecontrol shows time of day,timer and ovenfunctions.

Control panel shown includesmodel specific features. (Styling may vary depending on model.)

K{I{I{I{I{{I¸

ii ii ii!ii!ii!ii!ii!i!i

i;i;i;i;i;i;i;i;i;i;i_{ii_

Bake

Keep Warm

Broil

Toast

Clean

Delay

Cook & Hold

Timer

Clock

Oven Light

Less-/More+

CANCEL

Use for baking and roasting.

Use to keep cooked food warm in oven.

Usefor broiling and top browning.

Usefor toasting bread and products

toasted in toaster or toaster oven.

Use to set self-clean cycle.

Programsthe oven to start baking or

cleaning at a later time.

Bakes for a preset time, then keeps food

warm for 1 hour.

Sets timer.

Use to set time-of-day clock.

Useto turn the oven lights on or off.

Enters or changes time, oven

temperature. Sets HI or LO broil.

Cancels all operations except timer

and clock.

Using the Touchpads

• Pressthe desired pad.

• Press More+ or Less= pad to enter time or temperature.

• A beep will sound when any pad istouched.

• A double beep will sound ifa programming error occurs.

Important: Four seconds after pressing the More+ or Less-

pad, the time or temperature will automatically be entered. If

more than 30 seconds elapse between touching a function

pad and the More+ or Less- pad, the function will be

canceled and the display will return to the previous display.

Clock

The clock car) be set to display thne in a 12-hour or 24-hour

format. The clock isset at the factory for the 12-hour format.

To change the clock to 24-hoar format:

1. Pressand hold tire upper over) CANCEL

and Delay pads for several seconds.

2. Pressthe More+ or Less =pad to select

12 or 24 hour.

3. Set the time of day following the

directions below.

To set the Clock:

1. Pressthe Clock pad.

• The colon (:) flashes in the display.

2. Press More+ or Less= pad to set the time

of day.

° Colon continues flashing.

3. Pressthe Clock pad again or wait four

seconds.

• The colon stops flashing.

When electrical power is supplied or after a power

interruption, the last clock time before power was

interrupted will flash.

To recall the time of day when another time function is

showing, press the Clock pad.

Clock time cannot be changed when the oven has been

programmed for Bake, Clean, Delay or Cook & Hold.

Cont.

To cancel the Clock display:

If you do not want the time of day to display: _/_A__rr_"_

Press and hold the upper oven CANCEL

and Clock pads for several seconds. The

time of day will disappear from the display.

When the clock display is canceled, press

the Clock pad to briefly display the time of day.

To restore the Clock display:

Press and hold the upper oven CANCEL and Clock pads for

several seconds. The time of day will reappear in the display.

Timer

The timer can be set from one minute (1:00) up to 11 hours

and 59 minutes (11:59).

The timer can be used independentlyof any other oven

activity. It can also be set while another oven function is

operating.

The timer does not control the oven.

To set the Timer:

1. Press the Timer pad.

• "0:00" lights in the display.

• "Timer" will flash.

2. Press the More+ or Less= pad until the

correct time appears in the display.

° "Timer" will continue to flash.

3. PressTimer pad again or wait four seconds.

• The time begins counting down.

• The last minute of the timer countdown will be displayed

as seconds.

4. At the end of the set time, three long beeps will sound.

To cancel the Timer:

1. Press and hold the Timer pad for three seconds.

2. Press the Timer pad and set the time to 0:00.

Locking the Control

and Oven Doors

The touchpads and oven doors car/be locked for safety,

cleaning, or to prevent unwanted use. They will not function

when locked.

If the oven is currently in use, the touchpads and doors

cannot be locked.

The current time of day will remain in the display when the

controls are locked.

To lock both doors:

Press and hold the upper oven CANCEL and

Cook & Hold pads for three seconds.

"Lock" flashes in the display while both

oven doors lock. Once complete, "Lock"

stops flashing.

"OFF" is displayed for 10 seconds whenever a pad is touched.

To unlock both doors:

Press and hold the upper oven CANCEL and Cook & Hold

pads for three seconds.

"Lock" flashes and then disappears from the display.

"OFF" appears in the display for several seconds while

doors are unlocking.

Important: The touchpads and oven doors cannot be locked

if the oven temperature is400° For above.

Fault Codes

"Bake" or "Lock" may flash rapidly in the display to alert you if

there is an error or a problem. If "Bake" or "Lock" flash in the

display, press CANCEL pad. If "Bake" or "Lock" continue to

flash, disconnect power to the appliance. Wait a few minutes,

and then reconnect power. If the flashing still continues,

disconnect power to the appliance and call an authorized

servicer.

Adjusting the Sound Level

Tile factory default setting for sound ismedium (MEd), but it

can be changed to low (Lo) or high (HI). To change the

setting:

1. Pressand hold More+ and upper oven CANCEL pads for

three seconds. A beep will sound and the current sound

level ("Lo", "MEd" or "HI") will appear in the display.

2. Press More+ pad to increasesound level or the Less=

pad to decrease sound level.

3. Wait four seconds and the new setting will be accepted.

4. If the More+ or Less- pad isnot pressed within 30

seconds, the control will return to the existing settings.

Changing Temp °F/°C

The factory default setting for temperature is Fahrenheit. To

change the setting:

1. Pressand hold the upper oven Bake and CANCEL pads

for three seconds. A beep will sound and the current

setting (°F or °C) will appear in the display.

2. Pressthe More+ or Less= pad to change the setting

between °Fand °C.

3. Wait four seconds and the new setting will be accepted.

4. If the More+ or Less- pad is not pressed within 30

seconds, the control will return to the existing settings.

Return To Factory Default

Settings

The control can be reset to the factory default settings. To

return to the default settings:

1. Press and hold upper oven Keep Warm and CANCEL

pads for three seconds. A single beep will sound and "dEF'

(default) will appear in the display.

2. Press the More+ pad to choose the factory settings. "cLr"

(clear) will appear in the display.

3. Wait four seconds and the factory settings will be accepted.

4. If the More+ or Less- pad is not pressed within 30 seconds,

the control will return to the existing settings.

Setting Upper and Lower

Oven Functions

Baking

To set bake:

Bake

1. Press the Bake pad for desired oven. ................................

• "Bake" will flash.

° "000°'' will flash in the display.

2. Select the oven temperature. The oven

temperature can be set from 170° to 550°. Press

or press and hold the More+ or Less- pad.

° "350°" will light when either pad is first pressed.

• Press the More+ pad to increase the temperature.

• Press the Less- pad to decrease the temperature.

3. Press Bake pad again or wait four seconds.

° "Bake" will stop flashing and light in the display.

° "Preheat" will light in the display.

• 100° or the actual oven temperature will display. The

temperature will rise in 5° increments until the preset

temperature is reached.

4. Allow 4-10 minutes for upper oven to preheat and 7-12

minutes for lower oven to preheat.

• When the set oven temperature is reached, one long

beep will sound.

• To recall the set temperature during preheat, press the

Bake pad.

To change the oven temperature during preheat, press

Bake once and reset temperature.

5. Placefood in the oven.

6. Check cooking progress at minumum cooking time. Cook

longer if needed.

7. When cooking isfinished, press ('CAIXICFI_

CANCEL pad.

' 'j_Cy

8. Removefood from the oven.

Baking Differences Between Your Old

and New Oven

It isnormal to notice some baking time differences between a

new oven and an old one. See Adjusting the Oven Temperature

on page 15.

Notes:

If the lower oven is NOT in use, the upper oven will

preheat more quickly.

Allow at least 1/2-inch between the baking pan or

casserole and the top element in the upper oven.

Loaf, angel food or bundt pans are not recommended in

the upper oven.

Do not use temperatures below 140° Fto keep food warm

or below 200° Ffor cooking. Forfood safety reasons, lower

temperatures are not recommended.

The back part of the lower oven bake element will NOT

glow red during baking. This is normal.

When baking frozen, self-rise pizzas in the upper oven,

place the pizza on a cookie sheet to avoid overbrowning.

When preheating with a baking/pizza stone inside

the upper oven, do not set oven above 400 ° F. To use

baking/pizza stones at temperatures above 400 ° in

the upper oven, put stone in after the preheat beep.

To change the oven temperature during cooking, press the

Bake pad and then the More+ or Less= pad until you

reach the desired temperature.

If you forget to turn off the oven, itwill automatically turn

off at the end of 12 hours. If you wish to deactivate the

Automatic Shut-Off/Sabbath Mode feature, see page 14.

Cook & Hold

Cook & Hold allows you to bake for a preset amount of time,

followed by a one-hour Keep Warm cycle.

To set Cook & Hold:

1. Pressthe Cook & Hold pad once for upper

oven or twice for lower oven.

• "Bake" and "Hold" flash.

° "000°'' will flash in the display.

Cont.

2. Select the oven temperature. The oven

temperatureca,,besetfrom170°to ,

Press or press and hold the More+ or Less- pa&

• Press the More+ pad to increase the

temperature.

• Press the Less- pad to decrease the temperature.

3. Press Cook & Hold pad again ORwait four seconds to set

cook time.

• "Time" flashes.

• "0:00" flashes in the display

4. Enter the amount of time you want to cook by pressing the

More+ or Less- pad. Time can be set from 10 minutes

(10:00) to 11 hours, 59 minutes (11:59).

• "Bake", "Preheat" and "Hold" light in the display.

• The cooking time will start counting down.

• "100°'' or actual oven temperature will light in the

display.

When the cooking time has elapsed:

• Three beeps will sound.

• "Bake" will turn off.

• "Hold" will light.

After one hour in HOLD WARM:

• The oven will turn off. Three beeps will sound.

To cancel Cook & Hold at any time: C(_ANCFI_

Press the CANCEL pad. Remove food from oven.

\:£LCY

Delay Cook & Hold

When using Delay, the oven begins to cook later in the day.

Set the amount of time that you want to delay before the oven

turns on and how long you want to cook. The oven begins to

heat at the selected time and cooks for the specified length of

time, then keeps food warm for one hour.

Delay time can be set from 10 minutes (10:00) to 11 hours, 59

minutes (11:59).

To set a Delayed Baking cycle:

1. Pressthe Delay pad once for upper oven or

twice for lower oven.

• "dLY" and "0:00" flash in the display.

2. Pressthe More+ or Less= pad to set the

amount of time you want to delay the

Cook & Hold cycle.

While "dLY" isstill flashing:

3. Pressthe Cook & Hold pad.

• "000°'' flashes in the display.

• "Bake" and "Hold" flash.

4. Press More+ or Less= pad to enter the oven

temperature.

• "Bake" flashes.

• After several seconds, %:00" and "Time" flash.

• "Bake" and "Hold" remain steady.

5. Press More+ or Less= pad to set the baking time.

• "Time" flashes.

• After several seconds, the delay time will count down.

• "dLY", "Bake" and "Hold" light in the display.

When the Delay time has expired:

• "dLY" will turn off.

• Baking time and temperature are displayed.

• "Bake" and "Hold" are displayed.

When the oven starts:

• The baking time will count down.

• "dLY" will turn off.

• "Bake" and "Hold" will remain lit.

To cancel:

Press the CANCEL pad.

• All timed and untimed cooking functions will be

canceled.

• The time of day will reappear in the display.

Important:

Do not use delayed baking for items that require a

preheated oven, such as cakes, cookies, and breads.

Do not use delayed baking if oven is already hot.

Keep Warm

For safely keeping foods warm or for warming breads

and plates.

TO set Keep Warm: r,_p

1. Press the Keep Warm pad for the appropriate Warm

ove [/. ...........................

• "Warm" flashes.

• "000°'' flashes in the display.

2. Select the Keep Warm temperature. The Keep

Warm temperature can be set from 145° to

190°. Press or press and hold the More+ or

Less- pad.

° 170°will light when either pad isfirst pressed.

• Pressthe More+ pad to increasethe temperature.

• Pressthe Less- pad to decrease the temperature.

"Warm" and the temperature will be displayed while Keep

Warm isactive.

To cancel Keep Warm:

1. Press the CANCEL pad.

2. Remove food from the oven.

Toastirlg (upper oven only)

Fortoasting bread and products that are toasted in a toaster or

toaster oven, Toast time can be set from 10 seconds up to six

minutes,

1. Press the Toast pad. /_\

2. Select the toasting time. Press /_\

the More+ pad to increase /// (_H_L_q \\\

the time or press the Less- SS/_//_//_ \_

pad to decrease the time. f[ ............. "_

° "Toast" and the toasting

time will be displayed. The toasting time will begin to

count down.

Browning time may vary, watch toasting carefully to avoid

over-browning. Close oven door during toasting.

3. At the end of the set toasting time, the oven will beep.

Notes:

° Lower oven may not be operated while upper oven

is toasting. If the lower oven is operating when the

Toast pad is pressed, a beep will sound.

• Toasting is based on time not temperature.

• For more even browning results, preheat the oven 3-4

minutes.

• Toasting times will be shorter when the oven is hot or

when repeated toasting functions are done.

• For optimal results when toasting 4-5 pieces of bread or

other similar items, follow illustration above.

Notes:

• Foroptimal food quality, ovencooked foods should be kept

warm for no longer than 1 to 2 hours.

• To keep foods from drying, cover loosely with foil or a lid.

° To warm dinner rolls:

- cover rolls loosely with foil and place in oven.

- press Keep Warm and More+ pads to set 170° F.

- warm for 12-15 minutes.

° To warm plates:

- place 2 stacks of up to four plates each in the oven.

- press Keep Warm and More+ pads to set 170° F.

- warm for five minutes, turn off the oven and leave plates

in the oven for 15 minutes more.

- use only oven-safe plates, check with the manufacturer.

- do not set warm dishes on a cold surface as rapid

temperature changes could cause crazing or breakage.

Toasting Chart

Sliced White Bread

Waffles (frozen]

Toaster Pastry (unfrozen]

Toaster Pastry (frozen]

3V2- 4V2min.

4 - 4V2min.

3V2- 4 min.

4V2- 4% min

Tortillas (flour]

Toaster Breaks** or

Hot Pockets**

Bagels

English Muffins

Cheese Sandwich

4V2 - 5 min.

3V2 - 4 min.

3V2 - 4V2 min

Toasting times are approximate and should be used as a

guide only.

** Brand names are registered trademarks of the respective

manufacturers.

Broiling

To set Broih

1. Press the Broil pad for desired oven.

• "Broil" and "SEt" flash in the display.

f ................................

Bro,

2. Press the More+ or Less= pad once to set Hi broil. Press

the More+ or Less= pad twice to set LO broil.

° HI or LOwill be displayed.

• Select HI broil (550° F)for normal broiling. Select

LO broil (450° E/for low-temperature broiling of longer

cooking foods such as poultry.

3. After four seconds, the oven will start.

° "Broil" and HI or LO will remainlit.

4. Foroptimum browning, preheat broil element for 3-4

minutes before adding food.

5. Place food in the oven. Leaveoven door open about four

inches(the first stop).

6. Most meat should be turned once about halfway through

cooking.

7. When food iscooked, press the CANCEL pad.

Remove food and broiler pan from the oven.

° The time of day will reappear in the display.

Notes:

• For best results when broiling, use a two-piece

broiler pan.

° HI broil is used for most broiling. Use LO broil when

broiling longer cooking foods to allow them to cook to

well done stage without excessive browning.

• Broil times may be longer when the LO broil temperature

is selected.

• Never cover broiler pan insert with aluminum foil. This

prevents fat from draining to the pan below.

° Expect broil times to increase and browning to be slightly

lighter if appliance is installed on a 208-volt circuit.

° If more than 30 seconds elapse between pressing the

Broil pad and the More+ or Less- pad, the oven will not

be set and the display will return to the previous display.

• Most foods should be turned halfway through

broiling time.

Broiling Chart = Broil times are based on a 4 minute preheat.

Beef

Steak, 1"thick,

4 oz. Hamburgers, 3/4" thick (up to 12)

4 oz. Hamburgers, 3/4" thick (up to 6)

Chicken

Bone-in, skin-on breast

Pieces

Fish

Filets

Steaks, 1" thick

Pork

on rack

3or4

HI 8 - 11 (medium)

HI 15 - 20 (well)

HI 12 - 16 (well)

LO 25 - 36 (well)

LO 8 - 12 (flaky)

LO 10 - 14 (flaky)

15 - 19 (medium)

15 - 19 (well)

28 - 39 (well)

8 - 13 (flaky)

10- 16(flaky)

Chops, 1"thick on rack 4 HI 18 - 24 (well) 22 - 27 (well)

When broiling fish, spray broil pan insert with cooking oil. Do not turn fish filets.

** Broiling times are approximate and may vary depending on the thickness of the food. Turn meat halfway through cooking times.

Automatic Shut-Off/Sabbath

Mode

The ovens will automatically turn off after 12 hours if you

accidentally leave them on. The oven MUST be set for a

bake operation before setting the Automatic Shut=Off/

Sabbath Mode.

To cancel the 12=hour shut=off and run the

ovens continuously for 72 hours:

1. Set the oven to bake [see page 10].

2. Press and hold the Clock pad for five seconds.

• "SAbbAth"* will be displayed and flash for five seconds.

• "SAbbAth" will then be displayed continuously until

turned off or until the 72-hour time limit is reached.

• "Bake" and the oven temperature will also be displayed

if a bake setting is in use while the oven is in Sabbath

Mode.

All other functions EXCEPTBAKE (Timer, Keep Warm,

Clean, etc.] are locked out during the Sabbath Mode.

To cancel Bake when in Sabbath Mode:

Press the CANCEL pad.

• "Bake" and the oven temperature will turn

off in the display.

• "SabbAth" appears in the display.

• "Time" no longer appears in the display.

To cancel the Sabbath Mode:

1. Press the Clock pad for five seconds.

• "SAbbAth" will flash for 5 seconds.

° The time of day will return to the display.

2. After 72 hours, the Sabbath Mode will end.

• "SAbbAth" will flash for 5 seconds.

• The time of day will return to the display.

Notes:

Sabbath Mode can be turned on onlywhen the ovens

are on.

Sabbath Mode cannot be turned on if the touchpads are

locked out or when the doors are locked.

If the oven light is desired while in Sabbath Mode, it

must be turned on before the Sabbath Mode is started.

When the Sabbath Mode is started, no preheat beep will

sound.

All prompts, messages and beeps are deactivated when

Sabbath Mode is active.

The automatic door lock does not operate during the

Sabbath Mode.

Pressing CANCEL pad will cancel a bake cycle, however

the control will stay in the Sabbath Mode.

If power fails, the ovens will power up in Sabbath Mode

with 72 hours remaining and no cycle active.

* Important: "SAbbAth" appears in the display on two lines: SAb.

bath

Adjusting the Oven Temperature

Oven temperatures are carefully tested for accuracy at the

factory• It is normal to notice some baking or browning

differences between a new oven and an old one. As ranges

get older, the oven temperature can shift•

You may adjust the oven temperature if you think the oven is

not baking or browning correctly. To decide how much to

change the temperature, set the temperature 25° higher or

lower than your recipe recommends, then bake• The results

of the "test" should give you an idea of how much to adjust

the temperature•

To adjust the oven temperature:

• Bake1 Press the appropriate Bake pad.

2. Enter 550° by pressing the More+ pad.

3. Press and hold the Bake pad for several

seconds or until "0°'' and "AdJ" (which

signifies 'adjust') appear in the display.

If the oven temperature was previously adjusted, the

change will be displayed. For example, if the oven

temperature was reduced by 15° the display will show

,,_15°''"

4. Press the More+ or Less= pad to adjust the temperature.

Eachtime a pad ispressed, the temperature changes by

5°. The oven temperature can be increasedor decreased

by 5° to 35°.

5. The time of day will automatically reappear in the display

You do not need to readjust the oven temperature if there

isa power failure or interruption.Broiling and cleaning

temperatures cannot be adjusted.

Oven Vent

When the oven is in use the area near the vent may become

hot enough to cause burns. Never block the vent opening.

]'he oven vent is located below the backguard vent

shield on your range.

When high moisture foods are cooked in the upper oven,

steam may be visible coming from the oven vent. This is

normal.

OVEN VENT

T!ON

Do not place

plastics near the

vent opening as

heat from the vent

could distort or

melt the plastic.

Oven Lights

Tile oven lights automatically come on when an

oven door is opened. When the doors are closed,

press the appropriate Oven Light pad to turn the

oven lights on and off. A beep will sound every time

the Oven Light pad is pressed.

Oven Bottom

Protect oven bottom against spillovers, especially acidic or

sugary spills, as they may discolor the porcelain enamel. Use

the correct pan size to avoid spillovers and boilovers. Do not

place utensils or aluminum foil directly on the oven

bottom.

Oven Racks

All racks are designed with a lock-stop edge.

Upper oven

• Is equipped with one rack and rack

position.

• When pulling the upper oven rack out to

remove or check food, grasp the top edge

of the rack.

Lower oven

• Is equipped with one RollerGlideTM rack and one flat rack

(select models:)or two flat racks.

To remove oven racks:

• Pull rack straight out until it stops at the lock-stop position;

lift up on the front of the rack and pull out.

• For RollerGlideTM rack, pull both the rack glide and rack

base out together.

To replace oven racks:

• Place rack on the rack support in

the oven; tilt the front end up

slightly; slide rack back until it

clears the lock-stop position; lower

front and slide back into the oven.

Baking and Roasting with the

RollerGuide TM Rack (select models:)

Baking

• When baking on two racks, use the RollerGlideTM rack in

the lower rack position, and the flat rack in the upper rack

position.

Roasting

• When roasting large cuts of meat and poultry, use the

RollerGlideTM rack for ease of movement.

Cont.

Rack Positions (loweroven)

--5

--4

--3

--2

--1

RACK 5: Use for toasting bread or broiling very thin foods

and two-rack baking.

RACK 4: Use for two-rack baking and for broiling.

RACK 3: Use for most baked goods on a cookie sheet or jelly

roll pan, layer cakes, fruit pies, or frozen convenience foods

and for broiling.

RACK 2: Use for roasting small cuts of meat, casseroles,

baking loaves of bread, bundt cakes or custard pies and

two-rack baking.

RACK 1: Use for roasting large cuts of meat and poultry,

frozen pies, dessert souffles or angel food cake and two-rack

baking.

MULTIPLE RACK COOKING:

Two rack: Use rack positions 2 and 4, 1 and 4, or 2 and 5.

Baking Layer Cakes on Two Racks

For best results when baking cakes and cookies on two racks,

use racks 2 and 4.

Place the cakes on the rack as shown.

Half Rack Accessory

(Lower oven only)

A half rack, to increase oven

capacity, is available as an

accessory. It fits in the left, upper

portion of the lower oven and

provides space for a vegetable dish

when a large roaster is on the lower

rack. Contact your Maytag dealer for

the "HALFRACK" Accessory Kit or

call 1-877-232-6771 USA or

1-800-688-8408 Canada to order.

Care Clemn

Self-Clean Oven

The self-clean cycle uses above-normal cooking temperatures

to automatically clean the oven interior.

The oven should be cleaned regularly by wiping up spillovers

to prevent excessive smoke and flare-ups. Do not allow a

heavy build-up of soil to accumulate in the oven.

During the cleaning process, the kitchen should be well

ventilated to get rid of normal odors associated with cleaning.

Before Self=Cleaning

1. Turn off the oven light before cleaning. The light may burn

out during the clean cycle.

2. Remove broiler pan, all pans, and oven racks from the

oven. The oven racks will discolor and may not slide easily

after a self-clean cycle ifthey are not removed.

3. Clean oven frame, door frame, area _ _

outside of gasket, and around the "-

opening in the door gasket with a

nonabrasive cleaner such as Bon

Ami* or detergent and water. The

self-cleaning process does not

clean these areas. They should be

cleaned to prevent soil from baking on during the clean

cycle. 0-he gasket isthe seal around the oven door and

window.)

4. To prevent damage, do not clean or rub the gasket around

the oven door. The gasket isdesigned to seal in heat

during the clean cycle.

5. Wipe up excess grease or spillovers from the oven bottom.

This prevents excessive smoking, flare-ups or flaming

during the clean cycle.

6. Wipe up sugary and acidic spillovers such as sweet

potatoes, tomato, or milk-based sauces. Porcelain enamel

isacid-resistant, not acid-proof. The porcelain finish

may discolor ifacidic spills are not wiped up before a

self-clean cycle.

important:

• Oven temperature must be below 400° Fto program a

clean cycle.

• Only one oven can be cleaned at a time.

Both oven doors lock when either oven isbeing cleaned.

To set Self=Clean:

1. Close the oven door. Clean

2. Press the Clean pad.

• "Clean" and "SEt" flash in the display.

If the door is not closed within 25 seconds, the

self-cleaning operation will be canceled and the

display will return to the time of day.

3. Press the More+ or Less- pad.

• "MEd" for medium amount of soil (3 hours)

appears in the display.

If the door is not closed, "door" will appear in

the display. After 45 seconds, three beeps will

sound, the self-cleaning operation will be canceled

and the display will return to the time of day.

4. Press the More+ pad twice for heavy soil (4 hours).

• "HVy" will be displayed.

Press Less- pad twice for light soil (2 hours).

° "LITE" will be displayed.

Choosing the soil level of the oven automatically programs

the self-cleaning time. "Lock" flashes in the display.

5. After four seconds, the oven will start cleaning.

° The cleaning time will start counting down in the display.

° "Lock" will appear in the display and will flash until the

doors are locked. "Lock" will then remain lit.

• "Clean" will remain lit in the display.

To Delay a Self=Clean Cycle:

1. Press the Delay pad once for upper

oven and twice for lower oven.

• "dLY" flashes.

° %:00" flashes in the display.

2. Press the More+ or Less- pad to set the

amount of time you want to delaythe cycle.

Delay time can be set from ten minutes (10:00)

to 11 hours, 59 minutes (11:59). Cont.

Brand names for cleaning products are registered trademarks ofthe respective manufacturers.

Cleantn

3. Press the apropriate Clean pad while

"dLY" is flashing. Clean

• "Clean" and "Set" will flash.

If the door is not closed within 25 seconds, the self-

cleaning operation will be canceled and the display will

return to the time of day.

4. Press the More+ or Less- pad.

• "MEd" for medium amount of soil (3 hours]

is displayed.

If the door is not closed, "door" will appear in

the display. After 45 seconds, three beeps will sound, the

self-cleaning operation will be canceled and the display

will return to the time of day.

5. Press the More+ pad twice for heavy soil (4 hours].

• "HVy" will be displayed.

Press the Less- pad twice for light soil (2 hours].

° "LITE"will be displayed.

Choosing the soil level of the oven automatically programs

the self-cleaning time.

6. After four seconds, "Clean", "dLY" and "Lock" will appear

in the display to show that the oven is set for a delayed

clean operation. The delay time is displayed and will begin

to count down.

When the Self=Clean cycle starts:

° "dLY" will turn off.

• "Clean", "Hours", "Lock" and the clean time will appear

in the display.

To cancel the Self=Clean cycle:

Press the CANCEL pad. (CANCEL')

• All words disappear from the display.

• All functions are canceled.

° The time of day appears in the display.

During the Self-Clean Cycle

When "Lock" shows in tile display, both oven doors are

locked. To prevent damage to the doors, do not force the

doors open when "Lock" is displayed.

Smoke and Smells

You may see some smoke and smell an odor the first few

times the oven is cleaned. This is normal and will lessen in

time.

Smoke may also occur if the oven is heavily soiled or if a

broiler pan was left in the oven.

Sounds

As the oven heats, you may hear sounds of metal parts

expanding and contracting. This is normal and will not

damage the oven.

After Self-Cleaning

About one hour after the end of the self-clean cycle, "Lock"

will turn off. The doors can then be opened.

Some soil may leave a light gray, powdery ash. Remove

it with a damp cloth. If soil remains after wiping, that means

the clean cycle was not long enough. The soil will be re-

moved during the next clean cycle.

If oven racks were left in the oven and do not slide

smoothly after a clean cycle, wipe racks and rack supports

with a small amount of vegetable oil to make them easier to

move.

Fine lines may appear in the porcelain because it went

through heating and cooling. This isnormal and will not

affect performance.

A white discoloration may appear after cleaning if acidic

or sugary foods were not wiped up before the self=clean

cycle. This discoloration is normal and will not affect

performance.

Notes:

• If the oven door is left open, "door" will appear in the

display until the door is closed.

• If more than five seconds elapse between pressing the

Clean pad and the More+ or Less- pad, the program will

automatically return to the previous display.

° The oven door will be damaged if the oven door is

forced to open when "Lock" is still displayed.

La page charge ...

Maytag Gemini MER6765BAS Mode d'emploi

Marque: Maytag

Modèle: Gemini MER6765BAS

Catégorie: Cuisinières

Taper: Mode d'emploi

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Maytag Gemini MER6765BAS User guide
español: Maytag Gemini MER6765BAS Guía del usuario

Maytag Gemini MER6765BAS Mode d'emploi

Ce manuel convient également à

Maytag Gemini MER6765BAS Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents