Zanussi ZRB34312XA Manuel utilisateur

Marque: Zanussi

Modèle: ZRB34312XA

Catégorie: Congélateurs

Taper: Manuel utilisateur

User Manual 2

Notice d'utilisation 16

ZRB34312WA

ZRB34312XA

Fridge Freezer

Réfrigérateur/congélateur

Contents

Safety information 2

Safety instructions 3

Product description 5

Operation 6

Daily use 6

Hints and tips 8

Care and cleaning 9

Troubleshooting 10

Installation 12

Technical information 14

Subject to change without notice.

Safety information

Before the installation and use of the appliance, carefully read the

supplied instructions. The manufacturer is not responsible if an

incorrect installation and use causes injuries and damages.

Always keep the instructions with the appliance for future

reference.

Children and vulnerable people safety

• This appliance can be used by children aged from 8 years and

above and persons with reduced physical, sensory or mental

capabilities or lack of experience and knowledge if they have

been given supervision or instruction concerning use of the

appliance in a safe way and understand the hazards involved.

• Do not let children play with the appliance.

• Cleaning and user maintenance shall not be made by children

without supervision.

• Keep all packaging away from children.

General Safety

• This appliance is intended to be used in household and similar

applications such as:

– Farm houses; staff kitchen areas in shops, offices and other

working environments

– By clients in hotels, motels, bed and breakfast and other

residential type environments

• Keep ventilation openings, in the appliance enclosure or in the

built-in structure, clear of obstruction.

2 www.zanussi.com

• Do not use mechanical devices or other means to accelerate

the defrosting process, other than those recommended by the

manufacturer.

• Do not damage the refrigerant circuit.

• Do not use electrical appliances inside the food storage

compartments of the appliance, unless they are of the type

recommended by the manufacturer.

• Do not use water spray and steam to clean the appliance.

• Clean the appliance with a moist soft cloth. Only use neutral

detergents. Do not use abrasive products, abrasive cleaning

pads, solvents or metal objects.

• Do not store explosive substances such as aerosol cans with a

flammable propellant in this appliance.

• If the supply cord is damaged, it must be replaced by the

manufacturer, its service agent or similarly qualified persons in

order to avoid a hazard.

Safety instructions

Installation

WARNING!

Only a qualified person must install

this appliance.

• Remove all the packaging.

• Do not install or use a damaged appliance.

• Obey the installation instruction supplied

with the appliance.

• Always be careful when you move the

appliance because it is heavy. Always wear

safety gloves.

• Make sure the air can circulate around the

appliance.

• Wait at least 4 hours before connecting the

appliance to the power supply. This is to

allow the oil to flow back in the compressor.

• Do not install the appliance close to

radiators or cookers, oven or hobs.

• The rear of the appliance must stand against

the wall.

• Do not install the appliance where there is

direct sunlight.

• Do not install this appliance in areas that are

too humid or too colds, such as the

construction appendices, garages or wine

cellars.

• When you move the appliance, lift it by the

front edge to avoid scratching the floor.

Electrical connection

WARNING!

Risk of fire and electrical shock.

• The appliance must be earthed.

• All electrical connections should be made by

a qualified electrician.

• Make sure that the electrical information on

the rating plate agrees with the power

supply. If not, contact an electrician.

• Always use a correctly installed shockproof

socket.

• Do not use multi-plug adapters and

extension cables.

• Make sure not to cause damage to the

electrical components (e.g. mains plug,

mains cable, compressor). Contact the

Service or an electrician to change the

electrical components.

• The mains cable must stay below the level of

the mains plug.

• Connect the mains plug to the mains socket

only at the end of the installation. Make sure

that there is access to the mains plug after

the installation.

www.zanussi.com 3

• Do not pull the mains cable to disconnect

the appliance. Always pull the mains plug.

Use

WARNING!

Risk of injury, burns, electrical shock

or fire.

• Do not change the specification of this

appliance.

• Do not put electrical appliances (e.g. ice

cream makers) in the appliance unless they

are stated applicable by the manufacturer.

• Be careful not to cause damage to the

refrigerant circuit. It contains isobutane

(R600a), a natural gas with a high level of

environmental compatibility. This gas is

flammable.

• If damage occurs to the refrigerant circuit,

make sure that there are no flames and

sources of ignition in the room. Ventilate the

room.

• Do not let hot items to touch the plastic

parts of the appliance.

• Do not put soft drinks in the freezer

compartment. This will create pressure on

the drink container.

• Do not store flammable gas and liquid in the

appliance.

• Do not put flammable products or items that

are wet with flammable products in, near or

on the appliance.

• Do not touch the compressor or the

condenser. They are hot.

• Do not remove or touch items from the

freezer compartment if your hands are wet or

damp.

• Do not freeze again food that has been

thawed.

• Obey the storage instructions on the

packaging of frozen food.

Care and cleaning

WARNING!

Risk of injury or damage to the

appliance.

• Before maintenance, deactivate the

appliance and disconnect the mains plug

from the mains socket.

• This appliance contains hydrocarbons in the

cooling unit. Only a qualified person must do

the maintenance and the recharging of the

unit.

• Regularly examine the drain of the appliance

and if necessary, clean it. If the drain is

blocked, defrosted water collects in the

bottom of the appliance.

Disposal

WARNING!

Risk of injury or suffocation.

• Disconnect the appliance from the mains

supply.

• Cut off the mains cable and discard it.

• Remove the door to prevent children and

pets to be closed inside of the appliance.

• The refrigerant circuit and the insulation

materials of this appliance are ozone-friendly.

• The insulation foam contains flammable gas.

Contact your municipal authority for

information on how to discard the appliance

correctly.

• Do not cause damage to the part of the

cooling unit that is near the heat exchanger.

4 www.zanussi.com

Product description

Product overview

73 4 51 62

9 8

Vegetable drawers

Cabinet shelves

Dynamic Air Cooling

Bottle rack

Control panel

Door shelves

Bottle shelf

Freezer drawers

Rating plate

www.zanussi.com 5

Operation

Control panel

3 2

Temperature indicators LED

QuickChill button

Temperature regulator

Switching on

Insert the plug into the wall socket.

QuickChill function

You can activate the QuickChill function by

pressing the QuickChill button.

The LED corresponding to the symbol

QuickChill indicator lights up.

You can deactivate the QuickChill function by

pressing the QuickChill button again.

The QuickChill indicator will light off.

This function stops automatically

after 52 hours.

Temperature regulation

To operate the appliance, touch the

temperature regulator button until the LED

corresponding to the required temperature

lights up. Selection is progressive, varying from

2 to 8°C.

At first button touch actual setting LED keeps

blinking.

Any time the button is touch the set

temperature is moved to 1 position .

Corresponding LED will blink for a while.

Touch the setting button until the required

temperature is selected. The set will be fixed

Coldest setting: +2°C. Warmest

setting: +8°C. A medium setting is

generally the most suitable.

However, the exact setting should be chosen

keeping in mind that the temperature inside the

appliance depends on:

• room temperature

• how often the door is opened

• quantity of food stored

• appliance location.

Daily use

WARNING!

Refer to Safety chapters.

6 www.zanussi.com

Initial power on

CAUTION!

Before inserting the power plug in to

the outlet and switching on the

cabinet for the first time, leave the

appliance standing upright for at

least 4 hours. This will assure a

sufficient amount of time for the oil

to return to the compressor.

Otherwise the compressor or

electronic components may sustain

damage.

Storage of frozen food

When first starting-up or after a period out of

use, before putting the products in the

compartment let the appliance run at least 2

hours with the QuickChill function turned on.

If large quantities of food are to be stored,

remove all drawers from appliance and place

food on glass shelf to obtain the best

performance.

In the event of accidental defrosting,

for example due to a power failure, if

the power has been off for longer

that the value shown in the technical

data chart under "Rising time", the

defrosted food must be consumed

quickly or cooked immediately and

then re-frozen (after cooling).

Freezing fresh food

The freezer compartment is suitable for freezing

fresh food and storing frozen and deep-frozen

food for a long time.

To freeze small amount of fresh foods it is not

necessary to change the present setting.

To freeze fresh food activate the QuickChill

function at least 24 hours before placing the

food to be frozen in the freezer compartment.

Place the fresh food to be frozen in the bottom

compartment.

The maximum amount of food that can be frozen

in 24 hours is specified on the rating plate, a

label located on the inside of the appliance.

The freezing process lasts 24 hours: during this

period do not add other food to be frozen.

When the freezing process is completed, return

to the required temperature (see "QuickChill

Function").

In this condition, the refrigerator

compartment temperature might

drop below 0°C. If this occurs reset

the temperature regulator to a

warmer setting.

Thawing

Deep-frozen or frozen food, prior to being used,

can be thawed in the refrigerator compartment

or at room temperature, depending on the time

available for this operation.

Small pieces may even be cooked still frozen,

directly from the freezer: in this case, cooking

will take longer.

Dynamic air cooling

This device allows for rapid cooling of foods

and a more uniform temperature in the

refrigerator compartment.

To activate, press the switch (A) to turn on the

fan. A green light comes on.

If the requested temperature is reached, turn off

the fan by pressing the switch (A).

Switch on the fan when the ambient

temperature exceeds 25°C.

Movable shelves

The walls of the refrigerator are equipped with a

series of runners so that the shelves can be

positioned as desired.

www.zanussi.com 7

Positioning the door shelves

To permit storage of food packages of various

sizes, the door shelves can be placed at

different heights.

Gradually pull the shelf in the direction of the

arrows until it comes free, then reposition as

required.

Bottle rack

Place bottles (with the opening facing front) in

the pre-positioned shelf.

Removal of freezer baskets

The freezing baskets have a limit stop to prevent

their accidental removal or falling out. At the

time of its removal from the freezer, pull the

basket towards yourself and, upon reaching the

end point, remove the basket by tilting its front

upwards.

At the time of putting it back, slightly lift the

front of the basket to insert it into the freezer.

Once you are over the end points, push the

baskets back in their position.

Hints and tips

Normal operating sounds

The following sounds are normal during

operation:

• A faint gurgling and bubbling sound from

coils sound when refrigerant is pumped.

• A whirring and pulsating sound from the

compressor when refrigerant is pumped.

• A sudden cracking noise from inside

appliance caused by thermic dilatation (a

natural and not dangerous physical

phenomenon).

• A faint click noise from the temperature

regulator when the compressor switches on

or off.

Hints for energy saving

• Do not open the door frequently or leave it

open longer than absolutely necessary.

• If the ambient temperature is high and the

Temperature Regulator is set to low

temperature and the appliance is fully

loaded, the compressor may run

continuously, causing frost or ice on the

evaporator. If this happens, set the

Temperature Regulator toward warmer

settings to allow automatic defrosting and so

a saving in electricity consumption.

Hints for fresh food refrigeration

To obtain the best performance:

• do not store warm food or evaporating

liquids in the refrigerator

• do cover or wrap the food, particularly if it

has a strong flavour

• position food so that air can circulate freely

around it

8 www.zanussi.com

Hints for refrigeration

Useful hints:

• Meat (all types) : wrap in polythene bags and

place on the glass shelf above the vegetable

drawer.

• For safety, store in this way only one or two

days at the most.

• Cooked foods, cold dishes, etc..: these

should be covered and may be placed on

any shelf.

• Fruit and vegetables: these should be

thoroughly cleaned and placed in the special

drawer(s) provided.

• Butter and cheese: these should be placed

in special airtight containers or wrapped in

aluminium foil or polythene bags to exclude

as much air as possible.

• Bottles: these need a cap and should be

stored on the door bottle shelf, or (if

equipped) on the bottle rack.

• Bananas, potatoes, onions and garlic, if not

packed, must not be kept in the refrigerator.

Hints for freezing

To help you make the most of the freezing

process, here are some important hints:

• the maximum quantity of food which can be

frozen in 24 hrs. is shown on the rating

plate;

• the freezing process takes 24 hours. No

further food to be frozen should be added

during this period;

• freeze only top quality, fresh and thoroughly

cleaned, foodstuffs;

• prepare food in small portions to enable it to

be rapidly and completely frozen and to

make it possible subsequently to thaw only

the quantity required;

• wrap up the food in aluminium foil or

polythene and make sure that the packages

are airtight;

• do not allow fresh, unfrozen food to touch

food which is already frozen, thus avoiding a

rise in temperature of the latter;

• lean foods store better and longer than fatty

ones; salt reduces the storage life of food;

• water ices, if consumed immediately after

removal from the freezer compartment, can

possibly cause the skin to be freeze burnt;

• it is advisable to show the freezing in date on

each individual pack to enable you to keep

tab of the storage time.

Hints for storage of frozen food

To obtain the best performance from this

appliance, you should:

• make sure that the commercially frozen

foodstuffs were adequately stored by the

retailer;

• be sure that frozen foodstuffs are transferred

from the foodstore to the freezer in the

shortest possible time;

• not open the door frequently or leave it open

longer than absolutely necessary;

• once defrosted, food deteriorates rapidly

and cannot be refrozen;

• do not exceed the storage period indicated

by the food manufacturer.

Care and cleaning

WARNING!

Refer to Safety chapters.

Periodic cleaning

The equipment has to be cleaned regularly:

• clean the inside and accessories with

lukewarm water and some neutral soap.

• regularly check the door seals and wipe

clean to ensure they are clean and free from

debris.

• rinse and dry thoroughly.

Do not pull, move or damage any

pipes and/or cables inside the

cabinet. Never use detergents,

abrasive powders, highly perfumed

cleaning products or wax polishes to

clean the interior as this will damage

the surface and leave a strong

odour.

Clean the condenser (black grill) and the

compressor at the back of the appliance with a

brush. This operation will improve the

performance of the appliance and save

electricity consumption.

www.zanussi.com 9

Take care of not to damage the

cooling system. When moving the

cabinet, lift it by the front edge to

avoid scratching the floor.

Defrosting of the refrigerator

Frost is automatically eliminated from the

evaporator of the refrigerator compartment

every time the motor compressor stops, during

normal use. The defrost water drains out

through a trough into a special container at the

back of the appliance, over the motor

compressor, where it evaporates.

It is important to periodically clean the defrost

water drain hole in the middle of the refrigerator

compartment channel to prevent the water

overflowing and dripping onto the food inside.

Defrosting the freezer

The freezer compartment is frost free. This

means that there is no build up of frost when it

is in operation, neither on the internal walls nor

on the foods.

The absence of frost is due to the continuous

circulation of cold air inside the compartment,

driven by an automatically controlled fan.

Periods of non-operation

When the appliance is not in use for long

periods, take the following precautions:

1. Disconnect the appliance from electricity

supply.

2. Remove all food.

3. Clean the appliance and all accessories.

4. Leave the door/doors open to prevent

unpleasant smells.

WARNING!

If the cabinet will be kept on, ask

somebody to check it once in a

while to prevent the food inside from

spoiling in case of a power failure.

Troubleshooting

WARNING!

Refer to Safety chapters.

What to do if...

Problem Possible cause Solution

The appliance does not operate. The appliance is switched off. Switch on the appliance.

The mains plug is not connec-

ted to the mains socket cor-

rectly.

Connect the mains plug to the

mains socket correctly.

There is no voltage in the

mains socket.

Connect a different electrical appli-

ance to the mains socket. Contact

a qualified electrician.

The appliance is noisy. The appliance is not supported

properly.

Check if the appliance stands sta-

ble.

The lamp does not work. The lamp is in stand-by. Close and open the door.

10 www.zanussi.com

Problem Possible cause Solution

The lamp does not work. The lamp is defective. Contact the nearest Authorized

Service Centre.

The compressor operates contin-

ually.

Temperature is set incorrectly. Refer to "Operation" chapter.

Many food products were put

in at the same time.

Wait some hours and then check

the temperature again.

The room temperature is too

high.

Refer to climate class chart on the

rating plate.

Food products placed in the

appliance were too warm.

Allow food products to cool to

room temperature before storing.

The door is not closed correct-

ly.

Refer to "Closing the door".

The QuickChill function is

switched on.

Refer to "QuickChill function".

The compressor does not start

immediately after pressing the

QuickChill, or after changing the

temperature.

This is normal, no error has oc-

curred.

The compressor starts after a peri-

od of time.

Water flows inside the refrigera-

tor.

The water outlet is clogged. Clean the water outlet.

Food products prevent that

water flows into the water col-

lector.

Make sure that food products do

not touch the rear plate.

Water flows on the floor. The melting water outlet is not

connected to the evaporative

tray above the compressor.

Attach the melting water outlet to

the evaporative tray.

Temperature cannot be set. The QuickFreeze or QuickChill

function is switched on.

Switch off QuickFreeze or Quick-

Chill manually, or wait until the

function resets automatically to set

the temperature. Refer to "Quick-

Freeze or QuickChill function".

Door is misaligned or interferes

with ventilation grill.

The appliance is not levelled. Refer to "Levelling".

The temperature in the appliance

is too low/too high.

The temperature regulator is

not set correctly.

Set a higher/lower temperature.

The door is not closed correct-

ly.

Refer to "Closing the door".

www.zanussi.com 11

Problem Possible cause Solution

The food products' tempera-

ture is too high.

Let the food products temperature

decrease to room temperature be-

fore storage.

Many food products are stored

at the same time.

Store less food products at the

same time.

The door has been opened of-

ten.

Open the door only if necessary.

The QuickChill function is

switched on.

Refer to "QuickChill function".

There is no cold air circulation

in the appliance.

Make sure that there is cold air cir-

culation in the appliance.

If the advice does not lead to the

desired result, call the nearest

brand-mark service.

Closing the door

1. Clean the door gaskets.

2. If necessary, adjust the door. Refer to

"Installation".

3. If necessary, replace the defective door

gaskets. Contact the After Sales Service.

Replacing the lamp

The appliance is equipped with a longlife LED

interior light.

Only service is allowed to replace the lighting

device. Contact your After Sales Service.

Installation

WARNING!

Refer to Safety chapters.

Positioning

This appliance can be installed in a dry, well

ventilated indoor where the ambient

temperature corresponds to the climate class

indicated on the rating plate of the appliance:

Climate

class

Ambient temperature

SN +10°C to + 32°C

N +16°C to + 32°C

ST +16°C to + 38°C

T +16°C to + 43°C

Some functional problems might

occur for some types of models

when operating outside of that

range. The correct operation can

only be guaranteed within the

specified temperature range. If you

have any doubts regarding where to

install the appliance, please turn to

the vendor, to our customer service

or to the nearest Service Centre

Location

It must be possible to disconnect

the appliance from the mains power

supply; the plug must therefore be

easily accessible after installation.

The appliance should be installed well away

from sources of heat such as radiators, boilers,

direct sunlight etc. Ensure that air can circulate

freely around the back of the cabinet. To ensure

12 www.zanussi.com

best performance, if the appliance is positioned

below an overhanging wall unit, the minimum

distance between the top of the cabinet and the

wall unit must be at least 100 mm . Ideally,

however, the appliance should not be

positioned below overhanging wall units.

Accurate levelling is ensured by one or more

adjustable feet at the base of the cabinet.

min

100mm

20mm

min

100mm

In order to guarantee proper functioning in

ambient temperature above 38°C, it is advised

to have a 30mm separation between the sides

of the appliance and surrounding furniture.

Levelling

When placing the appliance ensure that it

stands level. This can be achieved by two

adjustable feet at the bottom in front.

Electrical connection

• Before plugging in, ensure that the voltage

and frequency shown on the rating plate

correspond to your domestic power supply.

• The appliance must be earthed. The power

supply cable plug is provided with a contact

for this purpose. If the domestic power

supply socket is not earthed, connect the

appliance to a separate earth in compliance

with current regulations, consulting a

qualified electrician.

• The manufacturer declines all responsibility if

the above safety precautions are not

observed.

• This appliance complies with the E.E.C.

Directives.

Door reversibility

WARNING!

Before carrying out any operations,

remove the plug from the power

socket.

CAUTION!

To carry out the following

operations, we suggest that this be

made with another person that will

keep a firm hold on the doors of the

appliance during the operations.

1. Open the door and empty the shelves.

2. Unscrew the screws of the upper hinge (1).

3. Remove the door from the middle hinge

pivot (2).

4. Place the cover of the upper hinge into the

holes on the opposite side.

5. Screw off the screws of the middle hinge

(3).

6. Remove the plugs on the upper side of both

doors and move them to the other side.

7. Remove the lower door from the lower

hinge pivot (4).

8. Screw off the pivot of the lower hinge (5)

and screw the lower hinge pivot (6) into the

left drill of the lower hinge.

www.zanussi.com 13

9. Screw off the screws of the lower hinge

and remove the hinge (8).

10. Screw off the lower cover plugs and screw

them into the hole on the opposite side (7).

11. Put the lower hinge on the opposite side

and fix it with the screws (8).

12. Place the lower door on the lower hinge

pivot (9).

13. Screw off the middle cover plugs and screw

them into the hole on the opposite side

(10).

14. Put the middle hinge on the opposite side

and fix it with the screws (11).

180

15. Place the upper door on the middle hinge

pivot (12).

16. Fix the door with upper hinge and fix it with

screws of it (13).

Do a final check to make sure that:

• All screws are tightened.

• The magnetic seal adheres to the

cabinet.

• The door opens and closes

correctly.

If the ambient temperature is cold

(i.e. in Winter), the gasket may not fit

perfectly to the cabinet. In that case,

wait for the natural fitting of the

gasket. In case you do not want to

carry out the above mentioned

operations, contact the nearest After

Sales Service Force. The After Sales

Service specialist will carry out the

reversibility of the doors at your cost.

Technical information

Technical data

Height mm 1845

14 www.zanussi.com

Width mm 595

Depth mm 642

Rising time Hours 18 h

Voltage Volts 230 - 240

Frequency Hz 50

The technical information are situated in the

rating plate, on the external or internal side of

the appliance and in the energy label.

ENVIRONMENTAL CONCERNS

Recycle the materials with the symbol . Put

the packaging in applicable containers to

recycle it. Help protect the environment and

human health and to recycle waste of electrical

and electronic appliances. Do not dispose

appliances marked with the symbol with the

household waste. Return the product to your

local recycling facility or contact your municipal

office.

www.zanussi.com 15

Table des matières

Consignes de sécurité 16

Instructions de sécurité 17

Description de l'appareil 19

Fonctionnement 20

Utilisation quotidienne 20

Conseils 22

Entretien et nettoyage 24

En cas d'anomalie de fonctionnement 24

Installation 27

Caractéristiques techniques 29

Sous réserve de modifications.

Consignes de sécurité

Avant d'installer et d'utiliser cet appareil, lisez soigneusement les

instructions fournies. Le fabricant ne peut être tenu pour

responsable des dommages et blessures liés à une mauvaise

installation ou utilisation. Conservez toujours cette notice avec

votre appareil pour vous y référer ultérieurement.

Sécurité des enfants et des personnes vulnérables

• Cet appareil peut être utilisé par des enfants âgés d'au moins 8

ans et par des personnes ayant des capacités physiques,

sensorielles ou mentales réduites ou dénuées d’expérience ou

de connaissance, s’ils (si elles) sont correctement surveillé(e)s

ou si des instructions relatives à l’utilisation de l'appareil en

toute sécurité leur ont été données et si les risques encourus

ont été appréhendées.

• Les enfants ne doivent pas jouer avec l’appareil.

• Le nettoyage et l’entretien par l'usager ne doivent pas être

effectués par des enfants sans surveillance.

• Ne laissez pas les emballages à la portée des enfants.

Consignes générales de sécurité

• Cet appareil est conçu uniquement pour un usage domestique

et des utilisations telles que :

– dans les bâtiments de ferme, dans des cuisines réservées

aux employés dans des magasins, bureaux et autres lieux de

travail ;

– pour une utilisation privée, par les clients, dans des hôtels et

autres lieux de séjour.

16 www.zanussi.com

• Veillez à ce que les orifices de ventilation, situés dans l'enceinte

de l'appareil ou dans la structure intégrée, ne soient pas

obstrués.

• N'utilisez aucun dispositif mécanique ou autre appareil pour

accélérer le processus de dégivrage que ceux recommandés

par le fabricant.

• N'endommagez pas le circuit frigorifique.

• N'utilisez pas d'appareils électriques à l'intérieur des

compartiments de conservation des aliments de l'appareil, sauf

s'ils sont du type recommandé par le fabricant.

• Ne pulvérisez pas d'eau ni de vapeur pour nettoyer l'appareil.

• Nettoyez l'appareil avec un chiffon doux humide. Utilisez

uniquement des produits de nettoyage neutres. N'utilisez pas

de produits abrasifs, de tampons à récurer, de solvants ni

d'objets métalliques.

• Ne conservez aucune substance explosive dans cet appareil,

comme des aérosols contenant un produit inflammable.

• Si le câble d'alimentation est endommagé, il doit être remplacé

par le fabricant, son service après-vente ou des personnes de

qualification similaire afin d'éviter un danger.

Instructions de sécurité

Installation

AVERTISSEMENT!

L'appareil doit être installé

uniquement par un professionnel

qualifié.

• Retirez l'intégralité de l'emballage

• N'installez pas et ne branchez pas un

appareil endommagé.

• Suivez scrupuleusement les instructions

d'installation fournies avec l'appareil.

• Soyez toujours vigilants lorsque vous

déplacez l'appareil car il est lourd. Portez

toujours des gants de sécurité.

• Assurez-vous que l'air circule autour de

l'appareil.

• Attendez au moins 4 heures avant de

brancher l'appareil sur le secteur. Cela

permet à l'huile de refouler dans le

compresseur.

• N'installez pas l'appareil à proximité d'un

radiateur, d'une cuisinière, d'un four ou d'une

table de cuisson.

• La surface arrière de l'appareil doit être

positionnée contre un mur.

• N'installez pas l'appareil dans un endroit

exposé à la lumière directe du soleil.

• N'installez pas l'appareil dans un endroit trop

humide ou trop froid, comme une

dépendance extérieure, un garage ou une

cave.

• Lorsque vous déplacez l'appareil, veillez à le

soulever par l'avant pour éviter de rayer le

sol.

Branchement électrique

AVERTISSEMENT!

Risque d'incendie ou

d'électrocution.

• L'appareil doit être relié à la terre.

www.zanussi.com 17

• L'ensemble des branchements électriques

doit être effectué par un technicien qualifié.

• Vérifiez que les données électriques figurant

sur la plaque signalétique correspondent à

celles de votre réseau. Si ce n'est pas le cas,

contactez un électricien.

• Utilisez toujours une prise de courant de

sécurité correctement installée.

• N'utilisez pas d'adaptateurs multiprises ni de

rallonges.

• Veillez à ne pas endommager les

composants électriques tels que la fiche

secteur, le câble d'alimentation ou le

compresseur. Contactez le service après-

vente ou un électricien pour changer les

composants électriques.

• Le câble d'alimentation doit rester en

dessous du niveau de la fiche secteur.

• Ne connectez la fiche d'alimentation secteur

à la prise de courant secteur qu'à la fin de

l'installation. Assurez-vous que la fiche

d'alimentation est accessible une fois

l'appareil installé.

• Ne tirez jamais sur le câble d'alimentation

électrique pour débrancher l'appareil. Tirez

toujours sur la fiche.

Usage

AVERTISSEMENT!

Risque de blessures, de brûlures,

d'électrocution ou d'incendie.

• Ne modifiez pas les caractéristiques de cet

appareil.

• Ne placez aucun appareil électrique

(sorbetière, etc.) dans l'appareil, en

l'absence d'indications du fabricant.

• Veillez à ne pas endommager le circuit

frigorifique. Il contient de l'isobutane

(R600a), un gaz naturel ayant un niveau

élevé de compatibilité environnementale. Ce

gaz est inflammable.

• Si le circuit frigorifique est endommagé,

assurez-vous de l'absence de flammes et de

sources d'ignition dans la pièce. Aérez la

pièce.

• Évitez tout contact d'éléments chauds avec

les parties en plastique de l'appareil.

• Ne placez jamais de boissons gazeuses

dans le congélateur. Cela engendrerait une

pression sur le récipient de la boisson.

• Ne stockez jamais de gaz ou de liquide

inflammable dans l'appareil.

• Ne placez pas de produits inflammables ou

d'éléments imbibés de produits inflammables

à l'intérieur ou à proximité de l'appareil, ni sur

celui-ci.

• Ne touchez pas le compresseur ni le

condenseur. Ils sont chauds.

• Ne retirez pas et ne touchez pas les

éléments du compartiment congélateur avec

les mains mouillées ou humides.

• Ne recongelez jamais un aliment qui a été

décongelé.

• Respectez les instructions de stockage

figurant sur l'emballage des aliments

surgelés.

Entretien et nettoyage

AVERTISSEMENT!

Risque de blessure corporelle ou de

dommages matériels.

• Avant toute opération d'entretien, éteignez

l'appareil et débranchez la fiche de la prise

secteur.

• Cet appareil contient des hydrocarbures

dans son circuit de réfrigération. L'entretien

et la recharge du circuit de réfrigération

doivent être effectués par un professionnel

qualifié.

• Examinez régulièrement l'écoulement de

l'appareil et si nécessaire, nettoyez-le. Si

l'orifice est bouché, l'eau provenant du

dégivrage s'écoulera en bas de l'appareil.

Mise au rebut

AVERTISSEMENT!

Risque de blessure ou d'asphyxie.

• Débranchez l'appareil de l'alimentation

électrique.

• Coupez le câble d'alimentation et mettez-le

au rebut.

• Retirez la porte pour empêcher les enfants

et les animaux de s'enfermer dans l'appareil.

• Le circuit frigorifique et les matériaux

d'isolation de cet appareil préservent la

couche d'ozone.

• La mousse isolante contient un gaz

inflammable. Contactez votre service

municipal pour obtenir des informations sur

la marche à suivre pour mettre l'appareil au

rebut.

• N'endommagez pas la partie du circuit de

réfrigération située à proximité du

condenseur thermique.

18 www.zanussi.com

Description de l'appareil

Vue d'ensemble du produit

73 4 51 62

9 8

Bacs à légumes

Clayettes

Refroidissement dynamique de l'air

Compartiment à bouteilles

Panneau de commande

Balconnets de porte

Compartiment à bouteilles

Tiroirs du congélateur

Plaque de calibrage

www.zanussi.com 19

Fonctionnement

Bandeau de commande

3 2

Indicateurs de température LED

Touche QuickChill

Thermostat

Mise en marche

Insérez la fiche dans la prise murale.

Fonction QuickChill

Pour activer la fonction QuickChill, appuyez sur

la touche QuickChill.

Le voyant LED correspondant au symbole

QuickChill s'allume.

Pour désactiver la fonction QuickChill, appuyez

de nouveau sur la touche QuickChill.

Le voyant QuickChill s'éteint.

Cette fonction s'arrête

automatiquement au bout de

52 heures.

Réglage de la température

Pour mettre l'appareil en marche, appuyez sur la

touche du thermostat jusqu'à ce que le voyant

LED correspondant à la température souhaitée

apparaisse. La sélection se fait progressivement

de 2 °C à 8 °C

Lorsque vous appuyez sur la touche la première

fois, le voyant LED du réglage actuel continue

de clignoter.

À chaque fois que vous appuyez sur la touche,

la température réglée change d'un degré. Le

voyant LED correspondant clignotera un instant.

Appuyez sur la touche de réglage, jusqu'à ce

que la température souhaitée s'affiche. Le

réglage sera maintenu

Réglage le plus froid : +2 °C.

Réglage le plus chaud : +8 °C. Un

réglage intermédiaire est

généralement le plus indiqué.

Toutefois, on obtiendra le réglage exact en

tenant compte du fait que la température à

l'intérieur de l'appareil dépend de plusieurs

facteurs :

• la température ambiante

• la fréquence d'ouverture de la porte

• la quantité de denrées entreposées

• l'emplacement de l'appareil.

Utilisation quotidienne

AVERTISSEMENT!

Reportez-vous aux chapitres

concernant la sécurité.

20 www.zanussi.com

La page charge ...

Zanussi ZRB34312XA Manuel utilisateur

Marque: Zanussi

Modèle: ZRB34312XA

Catégorie: Congélateurs

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Zanussi ZRB34312XA User manual

Zanussi ZRB34312XA Manuel utilisateur

Zanussi ZRB34312XA Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents