Zanussi ZRB934PW2 Manuel utilisateur

Catégorie
Réfrigérateurs-congélateurs
Taper
Manuel utilisateur
EN
User manual 2
FR
Notice d'utilisation 15
Fridge Freezer
Réfrigérateur/congélateur
ZRB934PW2
Contents
Safety instructions _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2
Product description _ _ _ _ _ _ _ _ _ _ _ _ _ 5
Operation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 5
First use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 6
Daily use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 6
Helpful hints and tips _ _ _ _ _ _ _ _ _ _ _ _ 7
Care and cleaning _ _ _ _ _ _ _ _ _ _ _ _ _ _ 8
Troubleshooting _ _ _ _ _ _ _ _ _ _ _ _ _ _ 10
Technical data _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 12
Installation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 12
Environmental concerns _ _ _ _ _ _ _ _ _ _ 14
Subject to change without notice.
Safety instructions
In the interest of your safety and to ensure the
correct use, before installing and first using the
appliance, read this user manual carefully, in-
cluding its hints and warnings. To avoid unnec-
essary mistakes and accidents, it is important
to ensure that all people using the appliance
are thoroughly familiar with its operation and
safety features. Save these instructions and
make sure that they remain with the appliance
if it is moved or sold, so that everyone using it
through its life will be properly informed on ap-
pliance use and safety.
For the safety of life and property keep the pre-
cautions of these user's instructions as the
manufacturer is not responsible for damages
caused by omission.
Children and vulnerable people safety
This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or
lack of experience and knowledge, unless
they have been given supervision or instruc-
tion concerning use of the appliance by a
person responsible for their safety.
Children should be supervised to ensure
that they do not play with the appliance.
Keep all packaging well away from children.
There is risk of suffocation.
If you are discarding the appliance pull the
plug out of the socket, cut the connection
cable (as close to the appliance as you can)
and remove the door to prevent playing chil-
dren to suffer electric shock or to close
themselves into it.
If this appliance featuring magnetic door
seals is to replace an older appliance having
a spring lock (latch) on the door or lid, be
sure to make that spring lock unusable be-
fore you discard the old appliance. This will
prevent it from becoming a death trap for a
child.
General safety
Warning!
Keep ventilation openings, in the appliance en-
closure or in the built-in structure, clear of ob-
struction.
The appliance is intended for keeping food-
stuff and/or beverages in a normal house-
hold and similar applications such as:
staff kitchen areas in shops, offices and
other working environments;
farm houses and by clients in hotels, mo-
tels and other residential type environ-
ments;
bed and breakfast type environments;
catering and similar non-retail applica-
tions.
Do not use a mechanical device or any artifi-
cial means to speed up the thawing process.
Do not use other electrical appliances (such
as ice cream makers) inside of refrigerating
appliances, unless they are approved for this
purpose by the manufacturer.
Do not damage the refrigerant circuit.
The refrigerant isobutane (R600a) is con-
tained within the refrigerant circuit of the ap-
pliance, a natural gas with a high level of en-
vironmental compatibility, which is neverthe-
less flammable.
2
www.zanussi.com
During transportation and installation of the
appliance, be certain that none of the com-
ponents of the refrigerant circuit become
damaged.
If the refrigerant circuit should become dam-
aged:
avoid open flames and sources of ignition
thoroughly ventilate the room in which the
appliance is situated
It is dangerous to alter the specifications or
modify this product in any way. Any damage
to the cord may cause a short-circuit, fire
and/or electric shock.
Warning! Any electrical component
(power cord, plug, compressor) must be
replaced by a certified service agent or quali-
fied service personnel to avoid hazard.
1. Power cord must not be lengthened.
2. Make sure that the power plug is not
squashed or damaged by the back of
the appliance. A squashed or damaged
power plug may overheat and cause a
fire.
3. Make sure that you can come to the
mains plug of the appliance.
4. Do not pull the mains cable.
5. If the power plug socket is loose, do not
insert the power plug. There is a risk of
electric shock or fire.
6. You must not operate the appliance
without the lamp cover (if foreseen) of
interior lighting.
This appliance is heavy. Care should be tak-
en when moving it.
Do not remove nor touch items from the
freezer compartment if your hands are
damp/wet, as this could cause skin abra-
sions or frost/freezer burns.
Avoid prolonged exposure of the appliance
to direct sunlight.
Bulb lamps (if foreseen) used in this appli-
ance are special purpose lamps selected for
household appliances use only. They are not
suitable for household room illumination.
Daily Use
Do not put hot pot on the plastic parts in the
appliance.
Do not store flammable gas and liquid in the
appliance, because they may explode.
Do not place food products directly against
the air outlet on the rear wall. (If the appli-
ance is Frost Free)
Frozen food must not be re-frozen once it
has been thawed out.
Store pre-packed frozen food in accordance
with the frozen food manufacturer's instruc-
tions.
Appliance's manufacturers storage recom-
mendations should be strictly adhered to.
Refer to relevant instructions.
Do not place carbonated or fizzy drinks in
the freezer compartment as it creates pres-
sure on the container, which may cause it to
explode, resulting in damage to the appli-
ance.
Ice lollies can cause frost burns if consumed
straight from the appliance.
Care and cleaning
Before maintenance, switch off the appli-
ance and disconnect the mains plug from
the mains socket.
Do not clean the appliance with metal ob-
jects.
Do not use sharp objects to remove frost
from the appliance. Use a plastic scraper.
Regularly examine the drain in the refrigera-
tor for defrosted water. If necessary, clean
the drain. If the drain is blocked, water will
collect in the bottom of the appliance.
Installation
Important! For electrical connection carefully
follow the instructions given in specific
paragraphs.
Unpack the appliance and check if there are
damages on it. Do not connect the appli-
ance if it is damaged. Report possible dam-
ages immediately to the place you bought it.
In that case retain packing.
3
www.zanussi.com
It is advisable to wait at least four hours be-
fore connecting the appliance to allow the oil
to flow back in the compressor.
Adequate air circulation should be around
the appliance, lacking this leads to overheat-
ing. To achieve sufficient ventilation follow
the instructions relevant to installation.
Wherever possible the back of the product
should be against a wall to avoid touching or
catching warm parts (compressor, condens-
er) to prevent possible burn.
The appliance must not be located close to
radiators or cookers.
Make sure that the mains plug is accessible
after the installation of the appliance.
Connect to potable water supply only (If a
water connection is foreseen).
Service
Any electrical work required to do the servic-
ing of the appliance should be carried out by
a qualified electrician or competent person.
This product must be serviced by an author-
ized Service Centre, and only genuine spare
parts must be used.
Environment Protection
This appliance does not contain gasses
which could damage the ozone layer, in
either its refrigerant circuit or insulation materi-
als. The appliance shall not be discarded to-
gether with the urban refuse and rubbish. The
insulation foam contains flammable gases: the
appliance shall be disposed according to the
applicable regulations to obtain from your local
authorities. Avoid damaging the cooling unit,
especially at the rear near the heat exchanger.
The materials used on this appliance marked
by the symbol
are recyclable.
4
www.zanussi.com
Product description
2 43 7 8 109
111314
5 61
12
1
Vegetable drawers
2
Glass shelf
3
Glass shelf
4
Glass shelf
5
Glass shelf
6
Control panel
7
Dairy shelf
8
Door shelf
9
Door shelf
10
Bottle shelf
11
Freezer basket
12
Maxibox basket
13
Freezer basket
14
Rating plate
Operation
Switching on
Insert the plug into the wall socket.
Turn the Temperature regulator clockwise to a
medium setting.
Switching off
To turn off the appliance, turn the Temperature
regulator to the "O" position.
Temperature regulation
The temperature is automatically regulated.
To operate the appliance, proceed as follows:
turn the Temperature regulator toward lower
settings to obtain the minimum coldness.
turn the Temperature regulator toward high-
er settings to obtain the maximum coldness.
5
www.zanussi.com
A medium setting is generally the most
suitable.
However, the exact setting should be chosen
keeping in mind that the temperature inside the
appliance depends on:
room temperature
how often the door is opened
the quantity of food stored
the location of the appliance.
Important! If the ambient temperature is high
or the appliance is fully loaded, and the
appliance is set to the lowest temperatures, it
may run continuously causing frost to form on
the rear wall. In this case the dial must be set
to a higher temperature to allow automatic
defrosting and therefore reduced energy
consumption.
First use
Cleaning the interior
Before using the appliance for the first time,
wash the interior and all internal accessories
with lukewarm water and some neutral soap so
as to remove the typical smell of a brand-new
product, then dry thoroughly.
Important! Do not use detergents or abrasive
powders, as these will damage the finish.
Daily use
Freezing fresh food
The freezer compartment is suitable for freez-
ing fresh food and storing frozen and deep-fro-
zen food for a long time.
To freeze fresh foods it is not necessary to
change the medium setting.
However, for a faster freezing operation, turn
the temperature regulator toward higher set-
tings to obtain the maximum coldness.
Important! In this condition, the refrigerator
compartment temperature might drop below
0°C. If this occurs reset the temperature
regulator to a warmer setting.
Place the fresh food to be frozen on the bottom
compartment.
Storage of frozen food
When first starting-up or after a period out of
use, before putting the products in the com-
partment let the appliance run at least 2 hours.
The freezer drawers ensure that it is quick and
easy to find the food package you want. If large
quantities of food are to be stored, remove all
drawers except for the bottom drawer which
needs to be in place to provide good air circu-
lation. On all shelves it is possible to place
food that protrude until 15 mm from the door.
Important! In the event of accidental
defrosting, for example due to a power failure,
if the power has been off for longer that the
value shown in the technical characteristics
chart under "rising time", the defrosted food
must be consumed quickly or cooked
immediately and then re-frozen (after cooling).
Thawing
Deep-frozen or frozen food, prior to being
used, can be thawed in the refrigerator com-
partment or at room temperature, depending
on the time available for this operation.
Small pieces may even be cooked still frozen,
directly from the freezer: in this case, cooking
will take longer.
Movable shelves
The walls of the refrigerator are equipped with
a series of runners so that the shelves can be
positioned as desired.
6
www.zanussi.com
Positioning the door shelves
To store various size food packages, the door
shelves can be placed at different heights.
Gradually pull the shelf in the direction of the
arrows until it comes free, then reposition as
required.
2
1
3
Removal of freezing baskets from the
freezer
The freezing baskets have a limit stop to pre-
vent their accidental removal or falling out. At
the time of its removal from the freezer, pull the
basket towards yourself and, upon reaching
the end point, remove the basket by tilting its
front upwards.
At the time of putting it back, slightly lift the
front of the basket to insert it into the freezer.
Once you are over the end points, push the
baskets back in their position.
12
Helpful hints and tips
Normal Operating Sounds
You may hear a faint gurgling and a bubbling
sound when the refrigerant is pumped
through the coils or tubing. This is correct.
When the compressor is on, the refrigerant
is being pumped around and you will hear a
whirring sound and a pulsating noise from
the compressor. This is correct.
The thermic dilatation might cause a sudden
cracking noise. It is natural, not dangerous
physical phenomenon. This is correct.
When the compressor switches on or
switches off, you will hear a faint "click" of
the temperature regulator. This is correct.
Hints for energy saving
Do not open the door frequently or leave it
open longer than absolutely necessary.
If the ambient temperature is high and the
Temperature Regulator is set to low temper-
ature and the appliance is fully loaded, the
compressor may run continuously, causing
frost or ice on the evaporator. If this hap-
pens, set the Temperature Regulator toward
warmer settings to allow automatic defrost-
ing and so a saving in electricity consump-
tion.
Hints for fresh food refrigeration
To obtain the best performance:
do not store warm food or evaporating liq-
uids in the refrigerator
do cover or wrap the food, particularly if it
has a strong flavour
position food so that air can circulate freely
around it
Hints for refrigeration
Useful hints:
Meat (all types) : wrap in polythene bags and
place on the glass shelf above the vegetable
drawer.
For safety, store in this way only one or two
days at the most.
Cooked foods, cold dishes, etc.: these should
be covered and may be placed on any shelf.
Fruits and vegetables: these should be thor-
oughly cleaned and placed in the special draw-
er(s) provided. When in contact, lemon juice
can discolor the plastic parts of your fridge. It
is therefore recommended to keep citruses in
separate containers.
7
www.zanussi.com
Butter and cheese: these should be placed in
special airtight containers or wrapped in alumi-
nium foil or polythene bags to exclude as much
air as possible.
Bottles: these should have a cap and should
be stored in the bottle rack on the door.
Bananas, potatoes, onions and garlic, if not
packed, must not be kept in the refrigerator.
Hints for freezing
To help you make the most of the freezing
process, here are some important hints:
the maximum quantity of food which can be
frozen in 24 hrs. is shown on the rating
plate;
the freezing process takes 24 hours. No fur-
ther food to be frozen should be added dur-
ing this period;
only freeze top quality, fresh and thoroughly
cleaned, foodstuffs;
prepare food in small portions to enable it to
be rapidly and completely frozen and to
make it possible subsequently to thaw only
the quantity required;
wrap up the food in aluminium foil or poly-
thene and make sure that the packages are
airtight;
do not allow fresh, unfrozen food to touch
food which is already frozen, thus avoiding a
rise in temperature of the latter;
lean foods store better and longer than fatty
ones; salt reduces the storage life of food;
water ices, if consumed immediately after re-
moval from the freezer compartment, can
possibly cause the skin to be freeze burnt;
it is advisable to show the freezing in date on
each individual pack to enable you to keep
tab of the storage time.
Hints for storage of frozen food
The freezer baskets ensure that it is quick and
easy to find the food package you want. If large
quantities of food are to be stored, remove all
drawers except for the bottom basket which
needs to be in place to provide good air circu-
lation.
To obtain the best performance from this appli-
ance, you should:
make sure that the commercially frozen food-
stuffs were adequately stored by the retailer;
be sure that frozen foodstuffs are transferred
from the foodstore to the freezer in the
shortest possible time;
not open the door frequently or leave it open
longer than absolutely necessary;
once defrosted, food deteriorates rapidly
and cannot be refrozen;
do not exceed the storage period indicated
by the food manufacturer.
Care and cleaning
Caution! Unplug the appliance before
carrying out any maintenance operation.
This appliance contains hydrocarbons in
its cooling unit; maintenance and recharg-
ing must therefore only be carried out by au-
thorized technicians.
Periodic cleaning
The equipment has to be cleaned regularly:
clean the inside and accessories with luke-
warm water and some neutral soap.
regularly check the door seals and wipe
clean to ensure they are clean and free from
debris.
rinse and dry thoroughly.
Important! Do not pull, move or damage any
pipes and/or cables inside the cabinet.
Never use detergents, abrasive powders,
highly perfumed cleaning products or wax
polishes to clean the interior as this will
damage the surface and leave a strong odour.
Clean the condenser (black grill) and the com-
pressor at the back of the appliance with a
brush. This operation will improve the perform-
ance of the appliance and save electricity con-
sumption.
Important! Take care of not to damage the
cooling system.
8
www.zanussi.com
Many proprietary kitchen surface cleaners con-
tain chemicals that can attack/damage the
plastics used in this appliance. For this reason
it is recommended that the outer casing of this
appliance is only cleaned with warm water with
a little washing-up liquid added.
After cleaning, reconnect the equipment to the
mains supply.
Defrosting of the refrigerator
Frost is automatically eliminated from the evap-
orator of the refrigerator compartment every
time the motor compressor stops, during nor-
mal use. The defrost water drains out through a
trough into a special container at the back of
the appliance, over the motor compressor,
where it evaporates.
It is important to periodically clean the defrost
water drain hole in the middle of the refrigera-
tor compartment channel to prevent the water
overflowing and dripping onto the food inside.
Use the special cleaner provided, which you
will find already inserted into the drain hole.
Defrosting the freezer
A certain amount of frost will always form on
the freezer shelves and around the top com-
partment.
Defrost the freezer when the frost layer rea-
ches a thickness of about 3-5 mm.
To remove the frost, follow the instructions be-
low:
pull out the plug from the wall socket or
switch off the appliance
remove any stored food, wrap it in several
layers of newspaper and put it in a cool
place
remove the freezer drawers
put insulating material around the drawers,
e.g. blankets or newspapers.
Defrosting can be accelerated by placing
bowls with hot water (not boiling) inside the
freezer.
Loosen the drainage channel from its resting
position, push it in according to the illustra-
tion and place it in the bottom freezer drawer
where water can collect
carefully scrape off the ice when it starts to
thaw. Use a wood or a plastic scraper
when all the ice has melted, clean and wipe
the cabinet dry, then put the drainage chan-
nel back in place.
switch on the cabinet and replace the frozen
foodstuff.
It is recommended to operate the appli-
ance at the highest position of the ther-
mostatic control for some hours so that it
can reach the sufficient storing tempera-
ture as soon as possible.
Important! Never use sharp metal tools to
scrape off frost from the evaporator as you
could damage it. Do not use a mechanical
device or any artificial means to speed up the
thawing process other than those
recommended by the manufacturer. A
temperature rise of the frozen food packs,
during defrosting, may shorten their safe
storage life.
9
www.zanussi.com
Troubleshooting
Caution! Before troubleshooting,
disconnect the power supply.
Only a qualified electrician or competent
person must do the troubleshooting that is not
in this manual.
Important! There are some sounds during
normal use (compressor, refrigerant
circulation).
Problem Possible cause Solution
The appliance is noisy. The appliance is not supported
properly.
Check if the appliance stands stable
(all the four feet should be on the
floor).
The compressor operates
continually.
The Temperature regulator may be
set incorrectly.
Set a warmer temperature.
The door is not closed correctly. Refer to "Closing the door".
The door has been opened too fre-
quently.
Do not keep the door open longer
than necessary.
The product temperature is too
high.
Let the product temperature de-
crease to room temperature before
storage.
The room temperature is too high. Decrease the room temperature.
Water flows on the rear
plate of the refrigerator.
During the automatic defrosting
process, frost defrosts on the rear
plate.
This is correct.
Water flows into the re-
frigerator.
The water outlet is clogged. Clean the water outlet.
Products prevent that water flows
into the water collector.
Make sure that products do not
touch the rear plate.
Water flows on the
ground.
The melting water outlet does not
flow in the evaporative tray above
the compressor.
Attach the melting water outlet to
the evaporative tray.
There is too much frost
and ice.
Products are not wrapped properly. Wrap the products better.
The door is not closed correctly. Refer to "Closing the door".
The Temperature regulator may be
set incorrectly.
Set a higher temperature.
The temperature in the ap-
pliance is too low.
The Temperature regulator may be
set incorrectly.
Set a higher temperature.
The temperature in the ap-
pliance is too high.
The Temperature regulator may be
set incorrectly.
Set a lower temperature.
The door is not closed correctly. Refer to "Closing the door".
The product temperature is too
high.
Let the product temperature de-
crease to room temperature before
storage.
10
www.zanussi.com
Problem Possible cause Solution
Many products are stored at the
same time.
Store less products at the same
time.
The temperature in the re-
frigeration is too high.
There is no cold air circulation in
the appliance.
Make sure that there is cold air cir-
culation in the appliance.
The temperature in the
freezer is too high.
Products are too near to each oth-
er.
Store products so that there is cold
air circulation.
The appliance does not
operate.
The appliance is switched off. Switch on the appliance.
The mains plug is not connected to
the mains socket correctly.
Connect the mains plug to the mains
socket correctly.
The appliance has no power. There
is no voltage in the mains socket.
Connect a different electrical appli-
ance to the mains socket. Contact a
qualified electrician.
The lamp does not work. The lamp is in stand-by. Close and open the door.
The lamp is defective. Refer to "Replacing the lamp".
If your appliance is still not working properly af-
ter making the above checks, contact the After
Sales Centre.
Replacing the lamp
1. Disconnect the appliance.
2. Push the movable part to unhook the lamp
cover (1).
3. Remove the lamp cover (2).
4. If needed replace the lamp with a light of
similar characteristic and power. It is sug-
gested to use Osram PARATHOM SPE-
CIAL T26 0.8 Watts.
5. Install the lamp cover.
6. Connect the appliance.
7. Open the door. Make sure that the lamp
comes on.
1
2
Closing the door
1. Clean the door gaskets.
2. If necessary, adjust the door. Refer to "In-
stallation".
3. If necessary, replace the defective door
gaskets. Contact the Service Center.
11
www.zanussi.com
Technical data
Dimension
Height 1750 mm
Width 595 mm
Depth 658 mm
Rising Time 20 h
Voltage 230-240 V
Frequency 50 Hz
The technical information are situated in the
rating plate on the internal left side of the appli-
ance and in the energy label.
Installation
Caution! Read the "Safety Information"
carefully for your safety and correct
operation of the appliance before installing the
appliance.
Positioning
Install this appliance at a location where the
ambient temperature corresponds to the cli-
mate class indicated on the rating plate of the
appliance:
Climate
class
Ambient temperature
SN +10°C to + 32°C
N +16°C to + 32°C
ST +16°C to + 38°C
T +16°C to + 43°C
Location
The appliance should be installed well away
from sources of heat such as radiators, boilers,
direct sunlight etc. Ensure that air can circulate
freely around the back of the cabinet. To en-
sure best performance, if the appliance is posi-
tioned below an overhanging wall unit, the min-
imum distance between the top of the cabinet
and the wall unit must be at least 100 mm .
Ideally, however, the appliance should not be
positioned below overhanging wall units. Accu-
rate levelling is ensured by one or more adjust-
able feet at the base of the cabinet.
Warning! It must be possible to
disconnect the appliance from the mains
power supply; the plug must therefore be
easily accessible after installation.
A
B
100 mm
min
20 mm
Rear spacers
You can find the two spacers in the bag with
documentation.
Do these steps to install the spacers:
1. Release the screw.
12
www.zanussi.com
2. Engage the spacer below the screw.
3. Turn the spacer to the right position.
4. Tighten again the screws.
2
4
3
1
Levelling
When placing the appliance ensure that it
stands level. This can be achieved by two ad-
justable feet at the bottom in front.
Electrical connection
Before plugging in, ensure that the voltage and
frequency shown on the rating plate corre-
spond to your domestic power supply.
The appliance must be earthed. The power
supply cable plug is provided with a contact for
this purpose. If the domestic power supply
socket is not earthed, connect the appliance to
a separate earth in compliance with current
regulations, consulting a qualified electrician.
The manufacturer declines all responsibility if
the above safety precautions are not observed.
This appliance complies with the E.E.C. Direc-
tives.
Door reversibility
Warning! Before carrying out any
operations, remove the plug from the
power socket.
Important! To carry out the following
operations, we suggest that another person
will keep a firm hold on the appliance doors
during the door reversing procedure.
Middle Hinge
Open the doors. Unscrew the middle hinge
(B). Remove the plastic spacer (A).
Remove the doors.
Remove the middle hinge cover pins (C,D)
and move them to the opposite side.
DC
A
B
Bottom Hinge
Unscrew the bottom hinge (A)
Remove the left-hand cover pins (D) and
move them to the opposite side.
Re-screw the bottom hinge (A) on the oppo-
site side.
Unscrew the bottom hinge pivot (B) and
spacer (C), and place them on the opposite
side.
D
A
B
C
Doors
Remove the plugs (A) on the top side of
both doors and move them to the opposite
side.
13
www.zanussi.com
A
Top Hinge
Unscrew the top hinge pivot (1) and place it
on the opposite side (2).
2
1
Insert the middle hinge into the bottom door.
Re-insert the bottom door into bottom hinge,
and then top door into top hinge pivot (1)
while slightly tilting both doors.
1
3
2
Re-screw the middle hinge (B), securing
both doors to the appliance. Do not forget
the plastic spacer (A).
Do a final check to make sure that:
All screws are tightened.
The edges of the doors run parallel to the
side edge of the appliance.
The magnetic seal adheres to the cabinet.
The door opens and closes correctly.
If the ambient temperature is cold (i.e. in Win-
ter), the gasket may not fit perfectly to the cabi-
net. In that case, wait for the natural fitting of
the gasket.
In case you do not want to carry out the above
mentioned operations, contact the nearest Af-
ter Sales Service Force. The After Sales Serv-
ice specialist will reverse the doors at your
cost.
Environmental concerns
Recycle the materials with the symbol . Put
the packaging in applicable containers to
recycle it.
Help protect the environment and human
health and to recycle waste of electrical and
electronic appliances. Do not dispose
appliances marked with the symbol
with the
household waste. Return the product to your
local recycling facility or contact your municipal
office.
14
www.zanussi.com
Sommaire
Instructions de sécurité _ _ _ _ _ _ _ _ _ _ 15
Description de l'appareil _ _ _ _ _ _ _ _ _ _ 18
Fonctionnement _ _ _ _ _ _ _ _ _ _ _ _ _ _ 18
Première utilisation _ _ _ _ _ _ _ _ _ _ _ _ _ 19
Utilisation quotidienne _ _ _ _ _ _ _ _ _ _ _ 19
Conseils utiles _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 20
Entretien et nettoyage _ _ _ _ _ _ _ _ _ _ _ 22
En cas d'anomalie de fonctionnement _ _ _ 23
Caractéristiques techniques _ _ _ _ _ _ _ _ 25
Installation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 26
En matière de sauvegarde de l'environnement
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 28
Sous réserve de modifications.
Instructions de sécurité
Pour votre sécurité et garantir une utilisation
correcte de l'appareil, lisez attentivement cette
notice, y compris les conseils et avertisse-
ments, avant d'installer et d'utiliser l'appareil
pour la première fois. Pour éviter toute erreur
ou accident, veillez à ce que toute personne
qui utilise l'appareil connaisse bien son fonc-
tionnement et ses fonctions de sécurité. Con-
servez cette notice avec l'appareil. Si l'appareil
doit être vendu ou cédé à une autre personne,
veillez à remettre cette notice au nouveau pro-
priétaire, afin qu'il puisse se familiariser avec
son fonctionnement et sa sécurité.
Pour la sécurité des personnes et des biens,
conservez et respectez les consignes de sécu-
rité figurant dans cette notice. Le fabricant dé-
cline toute responsabilité en cas de dommages
dus au non-respect de ces instructions.
Sécurité des enfants et des personnes
vulnérables
Cet appareil n'est pas destiné à être utilisé
par des enfants ou des personnes dont les
capacités physiques, sensorielles ou menta-
les, ou le manque d'expérience et de con-
naissance les empêchent d'utiliser l'appareil
sans risque lorsqu'ils sont sans surveillance
ou en l'absence d'instruction d'une personne
responsable qui puisse leur assurer une utili-
sation de l'appareil sans danger.
Empêchez les enfants de jouer avec l'appa-
reil.
Ne laissez pas les différents emballages à
portée des enfants. Ils pourraient s'asphyxier.
Si l'appareil doit être mis au rebut, sortez la
fiche de la prise électrique, coupez le cor-
don d'alimentation au ras de l'appareil et dé-
montez la porte pour éviter les risques
d'électrocution et que des enfants ne restent
enfermés à l'intérieur.
Cet appareil est muni de fermetures magné-
tiques. S'il remplace un appareil équipé
d'une fermeture à ressort, nous vous con-
seillons de rendre celle-ci inutilisable avant
de vous en débarrasser. Ceci afin d'éviter
aux enfants de s'enfermer dans l'appareil et
de mettre ainsi leur vie en danger.
Consignes générales de sécurité
Avertissement
Veillez à ce que les orifices de ventilation, situ-
és dans l'enceinte de l'appareil ou la structure
intégrée, ne soient pas obstrués.
Les appareils sont destinés uniquement à la
conservation des aliments et/ou des bois-
sons dans le cadre d’un usage domestique
normal, tel que celui décrit dans la présente
notice.
dans des cuisines réservées aux employés
dans des magasins, bureaux et autres
lieux de travail ;
dans les fermes et par les clients dans
des hôtels, motels et autres lieux de sé-
jour ;
dans des hébergements de type chambre
d'hôte ;
pour la restauration et autres utilisations
non commerciales.
N'utilisez pas d'appareils électriques,
d'agents chimiques ou tout autre système
artificiel pour accélérer le processus de dé-
givrage.
15
www.zanussi.com
Ne faites pas fonctionner d'appareils électri-
ques (comme des sorbetières électri-
ques, ...) à l'intérieur des appareils de réfri-
gération à moins que cette utilisation n'ait re-
çu l'agrément du fabricant.
N'endommagez pas le circuit frigorifique.
Le circuit frigorifique de l’appareil contient
de l’isobutane (R600a), un gaz naturel of-
frant un haut niveau de compatibilité avec
l’environnement mais qui est néanmoins in-
flammable.
Pendant le transport et l'installation de votre
appareil, assurez-vous qu'aucune partie du
circuit frigorifique n'est endommagée.
Si le circuit frigorifique est endommagé :
évitez les flammes vives et toute autre
source d'allumage
aérez soigneusement la pièce où se trou-
ve l'appareil
Ne modifiez pas les spécifications de l'appa-
reil. Si le câble d'alimentation est endomma-
gé, il peut causer un court circuit, un incen-
die et/ou une électrocution.
Avertissement Les éventuelles répara-
tions ou interventions sur votre appareil,
ainsi que le remplacement du câble d'alimenta-
tion, ne doivent être effectuées que par un pro-
fessionnel qualifié.
1. Ne branchez pas le cordon d'alimenta-
tion à une rallonge.
2. Assurez-vous que la prise n'est pas
écrasée ou endommagée par l'arrière de
l'appareil. Une prise de courant écrasée
ou endommagée peut s'échauffer et
causer un incendie.
3. Vérifiez que la prise murale de l'appareil
est accessible.
4. Ne débranchez pas l'appareil en tirant
sur le câble.
5. Si la prise murale n'est pas bien fixée,
n'introduisez pas de prise dedans. Ris-
que d'électrocution ou d'incendie.
6. N'utilisez pas l'appareil sans le diffuseur
de l'ampoule (si présent) de l'éclairage
intérieur.
Cet appareil est lourd. Faite attention lors de
son déplacement.
Ne touchez pas avec les mains humides les
surfaces givrées et les produits congelés
(risque de brûlure et d'arrachement de la
peau).
Évitez une exposition prolongée de l'appareil
aux rayons solaires.
Les ampoules (si présentes) utilisées dans
cet appareil sont des ampoules spécifiques
uniquement destinées à être utilisées sur
des appareils ménagers. Elles ne sont pas
du tout adaptées à un éclairage quelconque
d'une habitation.
Utilisation quotidienne
Ne posez pas d'éléments chauds sur les
parties en plastique de l'appareil.
Ne stockez pas de gaz ou de liquides inflam-
mables dans l'appareil (risque d'explosion).
Ne placez pas d'aliments directement contre
la sortie d'air sur la paroi arrière de l'appareil.
(Si l'appareil est sans givre.)
Un produit décongelé ne doit jamais être re-
congelé.
Conservez les aliments emballés conformé-
ment aux instructions de leur fabricant.
Respectez scrupuleusement les conseils de
conservation donnés par le fabricant de l'ap-
pareil. Consultez les instructions respecti-
ves.
Ne mettez pas de bouteilles ni de boîtes de
boissons gazeuses dans le compartiment
congélateur, car la pression se formant à l'in-
térieur du contenant pourrait le faire éclater
et endommager ainsi l'appareil.
Ne consommez pas certains produits tels
que les bâtonnets glacés dès leur sortie de
l'appareil, car ils peuvent provoquer des brû-
lures.
Entretien et nettoyage
Avant toute opération d'entretien, mettez
l'appareil hors tension et débranchez-le de la
prise de courant.
N'utilisez pas d'objets métalliques pour net-
toyer l'appareil.
16
www.zanussi.com
N'utilisez pas d'objet tranchant pour gratter
la couche de givre. Utilisez une spatule en
plastique.
Contrôlez régulièrement l'orifice d'évacuation
de l'eau de dégivrage dans le compartiment
réfrigérateur. Nettoyez-le, si besoin. Si l'orifi-
ce est bouché, l'eau s'écoulera en bas de
l'appareil.
Installation
Important Avant de procéder au branchement
électrique, respectez scrupuleusement les
instructions fournies dans cette notice.
Déballez l'appareil et vérifiez qu'il n'est pas
endommagé. Ne branchez pas l'appareil s'il
est endommagé. Signalez immédiatement au
revendeur de l'appareil les dommages cons-
tatés. Dans ce cas, gardez l'emballage.
Il est conseillé d'attendre au moins quatre
heures avant de brancher l'appareil pour que
le circuit frigorifique soit stabilisé.
Veillez à ce que l'air circule librement autour
de l'appareil pour éviter qu'il ne surchauffe.
Pour assurer une ventilation suffisante, res-
pectez les instructions de la notice (chapitre
Installation).
Placez l'appareil dos au mur pour éviter tout
contact avec le compresseur et le conden-
seur (risque de brûlure).
Placez de préférence votre appareil loin
d'une source de chaleur (chauffage, cuisson
ou rayons solaires trop intenses).
Assurez-vous que la prise murale reste ac-
cessible après l'installation de l'appareil.
Branchez à l'alimentation en eau potable uni-
quement. (Si un branchement sur le réseau
d'eau est prévu.)
Maintenance
Les branchements électriques nécessaires à
l'entretien de l'appareil doivent être réalisés
par un électricien qualifié ou une personne
compétente.
Cet appareil ne doit être entretenu et réparé
que par un Service après-vente autorisé, ex-
clusivement avec des pièces d'origine.
Protection de l'environnement
Le système frigorifique et l'isolation de vo-
tre appareil ne contiennent pas de C.F.C.
contribuant ainsi à préserver l'environnement.
L'appareil ne doit pas être mis au rebut avec
les ordures ménagères et les déchets urbains.
La mousse d'isolation contient des gaz inflam-
mables : l'appareil sera mis au rebut conformé-
ment aux règlements applicables disponibles
auprès des autorités locales. Veillez à ne pas
détériorer les circuits frigorifiques, notamment
au niveau du condenseur. Les matériaux utili-
sés dans cet appareil identifiés par le symbole
sont recyclables.
17
www.zanussi.com
Description de l'appareil
2 43 7 8 109
111314
5 61
12
1
Bacs à fruits
2
Clayette en verre
3
Clayette en verre
4
Clayette en verre
5
Clayette en verre
6
Thermostat
7
Compartiment à beurre
8
Balconnet de porte
9
Balconnet de porte
10
Compartiment à bouteilles
11
Panier de congélation
12
Bac Maxibox
13
Panier de congélation
14
Plaque signalétique
Fonctionnement
Mise en fonctionnement
Branchez l'appareil sur une prise murale.
Tournez le bouton du thermostat dans le sens
des aiguilles d'une montre sur une position
moyenne.
Mise à l'arrêt
Pour mettre à l'arrêt l'appareil, tournez le bou-
ton du thermostat sur la position "O".
Réglage de la température
La température est réglée automatiquement.
Pour faire fonctionner l'appareil, procédez
comme suit :
18
www.zanussi.com
tournez le bouton du thermostat vers le bas
pour obtenir un réglage de froid minimum.
tournez le bouton du thermostat vers le haut
pour obtenir un réglage de froid maximum.
Une position moyenne est la plus indi-
quée.
Toutefois, le réglage doit être choisi en tenant
compte du fait que la température à l'intérieur
de l'appareil dépend de plusieurs facteurs :
la température ambiante
la fréquence d'ouverture de la porte
la quantité de denrées stockées
l'emplacement de l'appareil.
Important Si le thermostat est réglé sur la
position de froid maximum, lorsque la
température ambiante est élevée et que
l'appareil est plein, il est possible que le
compresseur fonctionne en régime continu.
Dans ce cas, il y a un risque de formation
excessive de givre sur la paroi postérieure à
l'intérieur de l'appareil. Pour éviter cet
inconvénient, placez le thermostat sur une
température plus élevée de façon à permettre
un dégivrage automatique et, par conséquent,
des économies de courant.
Première utilisation
Nettoyage intérieur
Avant d'utiliser l'appareil pour la première fois,
nettoyez l'intérieur et tous les accessoires in-
ternes avec de l'eau tiède savonneuse pour
supprimer l'odeur caractéristique du "neuf"
puis séchez soigneusement.
Important N'utilisez pas de produits abrasifs,
poudre à récurer, éponge métallique pour ne
pas abîmer la finition.
Utilisation quotidienne
Congélation d'aliments frais
Le compartiment congélateur est idéal pour
congeler des denrées fraîches et conserver les
aliments surgelés ou congelés pendant long-
temps.
Pour congeler des aliments frais, il n'est pas
nécessaire de modifier le réglage moyen.
Toutefois, pour une congélation plus rapide,
tournez le thermostat vers le haut pour obtenir
plus de froid.
Important Dans ce cas, la température du
compartiment réfrigérateur peut chuter au-
dessous de 0°C. Si cela se produit,
repositionnez le thermostat sur un réglage plus
chaud.
Placez les denrées fraîches à congeler dans le
compartiment inférieur.
Conservation d'aliments congelés
À la mise en service ou après un arrêt prolon-
gé, faites fonctionner l'appareil pendant 2 heu-
res environ, avant d’introduire les produits dans
le compartiment.
Les tiroirs de congélation vous permettent de
trouver facilement et rapidement les aliments
dont vous avez besoin. Si vous devez stocker
une grande quantité d'aliments, retirez tous les
tiroirs et le bac à glace sauf le tiroir inférieur qui
doit être en place afin de permettre une circu-
lation d'air optimale. Des denrées alimentaires
peuvent être stockées sur chaque clayette en
respectant un espace de 15 mm max. à partir
de la porte.
Important En cas de décongélation
accidentelle, due par exemple à une coupure
de courant, si la coupure a duré plus de temps
qu'il n'est prévu au paragraphe « Autonomie de
fonctionnement », au chapitre Caractéristiques
techniques, consommez rapidement les
aliments décongelés ou cuisez-les
immédiatement avant de les recongeler (une
fois refroidis).
Décongélation
Avant utilisation, les aliments surgelés ou con-
gelés peuvent être décongelés dans le com-
19
www.zanussi.com
partiment du réfrigérateur ou à température
ambiante en fonction du temps disponible pour
cette opération.
Les petites portions peuvent même être cuites
sans décongélation préalable (la cuisson sera
cependant un peu plus longue).
Clayettes amovibles
Les parois du réfrigérateur sont équipées d'une
série de glissières pour que les clayettes puis-
sent être placées en fonction des besoins.
Emplacement des balconnets de la porte
Les balconnets de porte peuvent être placés à
différentes hauteurs pour permettre le range-
ment d'aliments de différentes tailles.
Tirez progressivement le balconnet dans le
sens des flèches pour le dégager, puis reposi-
tionnez-le selon les besoins.
2
1
3
Retrait des paniers de congélation du
congélateur
Les paniers de congélation sont équipés d'un
arrêt afin d'empêcher leur retrait accidentel ou
chute. Pour retirer le panier du congélateur, ti-
rez-le vers vous et en atteignant l'arrêt, retirez-
le en inclinant la partie avant vers le haut.
Pour le remettre, relevez légèrement l'avant du
panier et insérez-le dans le congélateur. Une
fois que vous avez dépassé les butées d'arrêt,
poussez les paniers dans la bonne position.
12
Conseils utiles
Bruits de fonctionnement normaux
Le liquide de refroidissement qui passe dans
le circuit d'évaporation peut produire un bruit
de gargouillis ou de bouillonnement. Ce
phénomène est normal.
Le compresseur peut produire un ronronne-
ment aigu ou un bruit de pulsation. Ce phé-
nomène est normal.
La dilatation thermique peut provoquer un
soudain, léger bruit de craquement. C'est un
phénomène normal et sans gravité. Ce phé-
nomène est normal.
Un léger claquement se produit lors de la
mise en fonctionnement/à l'arrêt du com-
presseur. Ce phénomène est normal.
Conseils pour l'économie d'énergie
N'ouvrez pas la porte trop souvent ou plus
longtemps que nécessaire.
20
www.zanussi.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32

Zanussi ZRB934PW2 Manuel utilisateur

Catégorie
Réfrigérateurs-congélateurs
Taper
Manuel utilisateur

dans d''autres langues