Yamaha DZR10 Le manuel du propriétaire

Marque: Yamaha

Modèle: DZR10

Catégorie: Égaliseurs audio

Taper: Le manuel du propriétaire

Ce manuel convient également à

Owner’s Manual

Bedienungsanleitung

Mode d’emploi

Manual de instrucciones

Manual do Proprietário

Manuale di istruzioni

Руководство пользователя

POWERED SPEAKER SYSTEM

POWERED SUBWOOFER

POWERED LOUDSPEAKER

Explanation of Graphical Symbols

Explication des symboles

The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated

“dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

L’éclair avec une flèche à l’intérieur d’un triangle équilatéral est destiné à attirer l’attention de l’utilisateur sur la présence d’une

« tension dangereuse » non isolée à l’intérieur de l’appareil, pouvant être suffisamment élevée pour constituer un risque d’électrocution.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and

maintenance (servicing) instructions in the literature accompanying the product.

Le point d’exclamation à l’intérieur d’un triangle équilatéral est destiné à attirer l’attention de l’utilisateur sur la présence

d’instructions importantes sur l’emploi ou la maintenance (réparation) de l’appareil dans la documentation fournie.

IMPORTANT SAFETY

INSTRUCTIONS

1 Read these instructions.

2 Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with dry cloth.

7 Do not block any ventilation openings. Install in accordance with

the manufacturer’s instructions.

8 Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including amplifiers) that

produce heat.

9 Do not defeat the safety purpose of the polarized or grounding-

type plug. A polarized plug has two blades with one wider than the

other. A grounding type plug has two blades and a third grounding

prong. The wide blade or the third prong are provided for your

safety. If the provided plug does not fit into your outlet, consult an

electrician for replacement of the obsolete outlet.

10 Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the point

where they exit from the apparatus.

11 Only use attachments/accessories specified by the manufacturer.

12 Use only with the cart, stand, tripod, bracket, or

table specified by the manufacturer, or sold with

the apparatus. When a cart is used, use caution

when moving the cart/apparatus combination to

avoid injury from tip-over.

13 Unplug this apparatus during lightning storms

or when unused for long periods of time.

14 Refer all servicing to qualified service personnel. Servicing is

required when the apparatus has been damaged in any way, such

as power-supply cord or plug is damaged, liquid has been spilled

or objects have fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate normally, or has

been dropped.

(UL60065_03)

PRÉCAUTIONS CONCER-

NANT LA SÉCURITÉ

1 Lire ces instructions.

2 Conserver ces instructions.

3 Tenir compte de tous les avertissements.

4 Suivre toutes les instructions.

5 Ne pas utiliser ce produit à proximité d’eau.

6 Nettoyer uniquement avec un chiffon propre et sec.

7 Ne pas bloquer les orifices de ventilation. Installer l’appareil

conformément aux instructions du fabricant.

8 Ne pas installer l’appareil à proximité d’une source de chaleur

comme un radiateur, une bouche de chaleur, un poêle ou tout

autre appareil (y compris un amplificateur) produisant de la

chaleur.

9 Ne pas modifier le système de sécurité de la fiche polarisée ou de

la fiche de terre. Une fiche polarisée dispose de deux broches dont

une est plus large que l’autre. Une fiche de terre dispose de deux

broches et d’une troisième pour le raccordement à la terre. Cette

broche plus large ou cette troisième broche est destinée à assurer

la sécurité de l’utilisateur. Si la fiche équipant l’appareil n’est pas

compatible avec les prises de courant disponibles, faire remplacer

les prises par un électricien.

10 Acheminer les cordons d’alimentation de sorte qu’ils ne soient

pas piétinés ni coincés, en faisant tout spécialement attention aux

fiches, prises de courant et au point de sortie de l’appareil.

11 Utiliser exclusivement les fixations et accessoires spécifiés par le

fabricant.

12 Utiliser exclusivement le chariot, le stand, le

trépied, le support ou la table recommandés par

le fabricant ou vendus avec cet appareil. Si

l’appareil est posé sur un chariot, déplacer le

chariot avec précaution pour éviter tout risque

de chute et de blessure.

13 Débrancher l’appareil en cas d’orage ou lorsqu’il doit rester hors

service pendant une période prolongée.

14 Confier toute réparation à un personnel qualifié. Faire réparer

l’appareil s’il a subi tout dommage, par exemple si la fiche ou le

cordon d’alimentation est endommagé, si du liquide a coulé ou

des objets sont tombés à l’intérieur de l’appareil, si l’appareil a été

exposé à la pluie ou à de l’humidité, si l’appareil ne fonctionne pas

normalement ou est tombé.

(UL60065_03)

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

ATTENTION :

POUR RÉDUIRE LES RISQUES D'ÉLECTROCUTION, NE PAS RETIRER

LE CAPOT (OU LE DOS). NE CONTIENT PAS DE PIÈCES NÉCESSITANT

L'INTERVENTION DE L'UTILISATEUR. POUR TOUTE INTERVENTION,

FAIRE APPEL À DES PROFESSIONNELS QUALIFIÉS.

ATTENTION

RISQUE DE CHOC

ELECTRIQUE-NE PAS OUVRIR

The above warning is located on the rear of the unit. L’avertissement ci-dessus est situé sur l’arrière de l’unité.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT

EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

AVERTISSEMENT

POUR RÉDUIRE LES RISQUES D’INCENDIE OU DE DÉCHARGE

ÉLECTRIQUE, N’EXPOSEZ PAS CET APPAREIL À LA PLUIE OU À

L’HUMIDITÉ.

(class I hokuo)

In Finland: Laite on liitettävä suojamaadoituskoskettimilla varustettuun pistorasiaan.

In Norway: Apparatet må tilkoples jordet stikkontakt.

In Sweden: Apparaten skall anslutas till jordat uttag.

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions con-

tained in this manual, meets FCC requirements. Modifications not

expressly approved by Yamaha may void your authority, granted

by the FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories

and/or another product use only high quality shielded cables.

Cable/s supplied with this product MUST be used. Follow all

installation instructions. Failure to follow instructions could void

your FCC authorization to use this product in the USA.

3. NOTE: This product has been tested and found to comply with

the requirements listed in FCC Regulations, Part 15 for Class “B”

digital devices. Compliance with these requirements provides a

reasonable level of assurance that your use of this product in a

residential environment will not result in harmful interference with

other electronic devices. This equipment generates/uses radio

frequencies and, if not installed and used according to the

instructions found in the users manual, may cause interference

harmful to the operation of other electronic devices. Compliance

with FCC regulations does not guarantee that interference will not

occur in all installations. If this product is found to be the source of

interference, which can be determined by tur

ning the u

nit “OFF”

and “ON”, please try to eliminate the problem by using one of the

following measures:

Relocate either this product or the device that is being affected by

the interference.

Utilize power outlets that are on different branch (circuit breaker

or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the

antenna. If the antenna lead-in is 300 ohm ribbon lead, change

the lead-in to co-axial type cable.

If these corrective measures do not produce satisfactory results,

please contact the local retailer authorized to distribute this type

of product. If you can not locate the appropriate retailer, please

contact Yamaha Corporation of America, Electronic Service Divi-

sion, 6600 Orangethorpe Ave, Buena Park, CA90620

The above statements apply ONLY to those products distributed

by Yamaha Corporation of America or its subsidiaries.

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B)

FCC INFORMATION (U.S.A.)

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (FCC DoC)

COMPLIANCE INFORMATION STATEMENT

(DECLARATION OF CONFORMITY PROCEDURE)

Responsible Party : Yamaha Corporation of America

Address : 6600 Orangethorpe Ave., Buena Park, Calif. 90620

Telephone : 714-522-9011

Type of Equipment : POWERED SPEAKER SYSTEM

Model Name : DZR315-D, DZR15-D, DZR12-D, DZR10-D, DXS18XLF-D, DXS15XLF-D

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1) this device may not cause harmful interference, and

2) this device must accept any interference received including interference that may cause

undesired operation.

See user manual instructions if interference to radio reception is suspected.

PRECAUTIONS

PLEASE READ CAREFULLY

BEFORE PROCEEDING

Please keep this manual in a safe place for

future reference.

WARNING

Always follow the basic precautions listed below to

avoid the possibility of serious injury or even death from

electrical shock, short-circuiting, damages, fire or other

hazards. These precautions include, but are not limited

to, the following:

If you notice any abnormality

• If any of the following problems occur, immediately turn off

the power switch and disconnect the electric plug from the

outlet.

- The power cord or plug becomes frayed or damaged.

- Unusual smells or smoke are emitted.

- Some object, or water has been dropped into the product.

- There is a sudden loss of sound during use of the product.

- Cracks or other visible damage appear on the product.

Then have the product inspected or repaired by qualified

Yamaha service personnel.

Power supply/power cord

• Do not place the power cord near heat sources such as

heaters or radiators, and do not excessively bend or

otherwise damage the cord, place heavy objects on it, or

place it in a position where anyone could walk on, trip over, or

roll anything over it.

• Only use the voltage specified as correct for the product. The

required voltage is printed on the name plate of the product.

• Use only the supplied power cord/plug.

If you intend to use the product in an area other than in the

one you purchased, the included power cord may not be

compatible. Please check with your Yamaha dealer.

• Check the electric plug periodically and remove any dirt or

dust which may have accumulated on it.

• Make sure to fully insert the electric plug to prevent electric

shocks or fire.

• When setting up the product, make sure that the AC outlet

you are using is easily accessible. If some trouble or

malfunction occurs, immediately turn off the power switch

and disconnect the plug from the outlet. Even when the

power switch is turned off, as long as the power cord is not

unplugged from the wall AC outlet, the product will not be

disconnected from the power source.

• Remove the electric plug from the outlet when the product is

not to be used for extended periods of time.

• Do not touch the product or the electric plug during an

electrical storm.

• Be sure to connect to an appropriate outlet with a protective

grounding connection. Improper grounding can result in

electrical shock, fire, or damage.

Do not open

• This product contains no user-serviceable parts. Do not

attempt to disassemble the internal parts or modify them in

any way.

Water warning/Fire warning

• Do not expose the product to rain, use it near water or in

damp or wet conditions, or place on it any containers (such

as vases, bottles or glasses) containing liquids which might

spill into any openings.

• Never insert or remove an electric plug with wet hands.

• Do not place any burning items or open flames near the

product, since they may cause a fire.

Hearing loss

• Before connecting the product to other devices, turn off the

power for all devices. Also, before turning the power of all

devices on or off, make sure that all volume levels are set to

the minimum. Failing to do so may result in hearing loss,

electric shock, or device damage.

• When turning on the AC power in your audio system, always

turn on the product LAST, to avoid hearing loss and speaker

damage. When turning the power off, the product should be

turned off FIRST for the same reason.

CAUTION

Always follow the basic precautions listed below to

avoid the possibility of physical injury to you or others,

or damage to the product or other property. These

precautions include, but are not limited to, the following:

Power supply/power cord

• When removing the electric plug from the product or an

outlet, always hold the plug itself and not the cord. Pulling by

the cord can damage it.

Location and connection

• Do not place the product in an unstable position where it

might accidentally fall over and cause injuries.

• Keep the device out of reach of children. This product is not

suitable for use in locations where children are likely to be

present.

• Do not block the vents. This product has ventilation holes at

the rear to prevent the internal temperature from becoming

too high. In particular, do not place the product on its side or

upside down. Inadequate ventilation can result in

overheating, possibly causing damage to the product(s), or

even fire.

• When attempting to dissipate heat on the product, when

installing it:

- Do not use the product in a confined, poorly-ventilated

location.

Inadequate ventilation can result in overheating, possibly

causing damage to the product(s), or even fire. Make sure

that there is adequate space around the rear panel: at least

30 cm above, 30 cm at the sides and 30 cm behind.

• Do not place the product in a location where it may come into

contact with corrosive gases or salt air. Doing so may result in

malfunction.

• Before moving the product, remove all connected cables.

PA_en_9 1/2

• When transporting or moving the product, always use two or

more people. Attempting to lift the product by yourself may

damage your back, result in other injury, or cause damage to

the product itself.

• Do not use the speaker’s handles for suspended installation.

Doing so can result in damage or injury.

• Do not hold the bottom of the product when transporting or

moving it. In doing so, you may pinch your hands under the

product, and result in injury.

• Do not press the rear panel of the product against the wall.

Doing so may cause the plug to come in contact with the wall

and detach from the power cord, resulting in short circuiting,

malfunction, or even fire.

• If you use the pole socket for mounting a satellite speaker

using a speaker pole, carefully read the section “r Dual pole

sockets” on page 7. Use of any other size pole may cause the

product to fall, and result in injury or damage to the internal

components.

• Always consult qualified Yamaha service personnel if the

product installation requires construction work, and make

sure to observe the following precautions.

- Choose mounting hardware and an installation location that

can support the weight of the product.

- Avoid locations that are exposed to constant vibration.

- Use the required tools to install the product.

- Inspect the product periodically.

Maintenance

• Remove the power plug from the AC outlet when cleaning the

product.

Handling caution

• Do not insert your fingers or hands in any gaps or openings

on the product (vents, ports, etc.).

• Do not operate the product if the sound is distorting.

Prolonged use in this condition could cause overheating and

result in fire.

NOTICE

To avoid the possibility of malfunction/damage to the product,

damage to data, or damage to other property, follow the notices

below.

 Handling and maintenance

• Do not use the product in the vicinity of a TV, radio, AV

equipment, mobile phone, or other electric products. Oth-

erwise, the product, TV, or radio may generate noise.

• Do not expose the product to excessive dust or vibration,

or extreme cold or heat (such as in direct sunlight, near a

heater, or in a car during the day), in order to prevent the

possibility of panel disfiguration, unstable operation, or

damage to the internal components.

• Condensation can occur in the product due to rapid, dras-

tic changes in ambient temperature—when the product is

moved from one location to another, or air conditioning is

turned on or off, for example. Using the product while con-

densation is present can cause damage. If there is reason

to believe that condensation might have occurred, leave

the product for several hours without turning on the power

until the condensation has completely dried out.

• Do not place the speaker face down with the grille

attached, as deformation of the grille may result.

• When placing the speaker face down, always place it on a

flat surface.

• Do not touch the speaker driver unit.

• Air blowing out of the bass reflex ports is normal, and often

occurs when the speaker is handling program material

with heavy bass content.

• During extreme changes in temperature or humidity, con-

densation may occur and water may collect on the surface

of the product. If water is left, the wooden parts may

absorb the water and be damaged. Make sure to wipe any

water off immediately with a soft cloth.

 Connectors

• XLR-type connectors are wired as follows (IEC60268 stan-

dard): pin 1: ground, pin 2: hot (+), and pin 3: cold (-).

Information

 About functions/data bundled with the prod-

uct

• This product uses Dante Ultimo. Refer to the Audinate

website (English) for details on the open‐source licenses

for the particular software.

https://www.audinate.com/software-licensing

 About this manual

• The illustrations and LCD screens as shown in this manual

are for instructional purposes only.

• The bitmap fonts used in this instrument have been pro-

vided by and are the property of Ricoh Co., Ltd.

• The company names and product names in this manual

are the trademarks or registered trademarks of their

respective companies.

• Software may be revised and updated without prior notice.

 About disposal

• This product contains recyclable components. When dis-

posing of this product, please contact the appropriate

local authorities.

Yamaha cannot be held responsible for damage caused by

improper use or modifications to the product, or data that is

lost or destroyed.

PA_en_9 2/2

Introduction

Thank you for purchasing the Yamaha DZR(-D) series POWERED LOUDSPEAKER and DXS-XLF(-D)

series POWERED SUBWOOFER. (See the series product lineup below.) These products are designed for

live performance, sound reinforcement and fixed installation sound system applications. This manual

explains how to install, set up, and configure the connections for the installers, constructors, or general

users familiar with speakers. Please read this manual thoroughly before you begin using this product in

order to get the most out of its various functions. After reading this manual, please keep it available for

future reference.

• The example illustrations used in this manual are taken from the DZR12-D and DXS18XLF-D, if not otherwise specified.

DZR(-D), DXS-XLF(-D) Series Product Lineup

Contents

PRECAUTIONS ..................................................................... 4

Introduction ........................................................................... 6

Main Features........................................................................ 6

Structure of Manuals ............................................................. 6

Included Accessories............................................................ 6

Functions............................................................................... 7

HOME Screen...................................................................... 10

Main Menus and Examples of Screens............................... 11

Screen Operations .............................................................. 12

Using a USB Flash Drive to Save/Load Data ...................... 12

Basic Settings......................................................................13

Dante Connection................................................................14

Cardioid Mode Settings.......................................................15

Rotatable Horn.....................................................................16

Installation Examples...........................................................17

Optional Accessories (sold separately)...............................19

Troubleshooting ...................................................................19

General Specifications (English only)................................151

Dimensions (English only) .................................................153

Main Features

• Strong plywood cabinet features a high output Class D amplifier. Full-range models feature a powerful and lightweight neo-

dymium magnet.

• Optimized pairing of a highly durable speaker unit with a fixed directional horn, for sparkling highs with punchy and powerful

bass.

• Full-range models feature an FIR filter for crossover and frequency adjustments. Low latency for DSP and AD/DA, thanks to 96

kHz sampling rate.

• LCD screen for loading presets, and for making precise graphical adjustments to EQ, delay, and routings. Easily transfer set-

tings to a USB flash drive.

• Dante models (-D) support the transmission of digital audio and remote control via a Dante network.

• 2-way models support use on a stand or use as a floor monitor. Rotation of the horn, several rigging points, and optional

brackets allow a variety of installation methods.

Structure of Manuals

• Owner’s Manual (this book): Mainly provides explana-

tions of the names, functions, and basic operations of each

component.

• Reference Manual: Mainly provides detailed explanations

of settings and operations. This can be downloaded from

the Yamaha Pro Audio global website.

https://www.yamaha.com/proaudio/

Included Accessories

• Power cord

• Owner’s Manual (this book)

Type Standard Model Dante Model (-D)

Full Range

3-way 15" DZR315 DZR315-D

2-way 15" DZR15 DZR15-D

2-way 12" DZR12 DZR12-D

2-way 10" DZR10 DZR10-D

Subwoofer

18" DXS18XLF DXS18XLF-D

15" DXS15XLF DXS15XLF-D

Dante

Dante is a network audio transmission protocol developed by Audinate. It allows the transmission of uncompressed multi-channel digital

audio at low latency, as well as sample-level synchronization. Wiring is kept simple through connections using CAT5e cables.

Full-range Speaker (Rear)

q Tiltable pole socket

This mount has two pole sockets. You can choose the

angle of the speaker so that it is positioned horizontal to

the floor or tilting down toward the floor by 7 degrees.

Compatible with commercially available speaker stands

and speaker poles of 35 mm diameter. (These sockets are

not available on the DZR315(-D).)

w Screw holes for U-bracket

For installing with the separately sold U-brackets. (These

sockets are not available on the DZR315(-D).)

e Screw holes for eye bolts

For installing the speaker using eye bolts. The screw holes

for eye bolts go through the cabinet wall.

Subwoofer (Rear)

r Dual pole sockets

Compatible with commercially available speaker poles of

35 mm diameter and M20 screw.

When using a pole socket to install a speaker, observe the

following conditions for safety.

t Feet cups

When stacking multiple speakers, align the rubber feet of

the upper speaker to the feet cups of the lower one.

y Wheel mounting screws

For installing the separately sold Yamaha SPW-1 wheels. If

you are not using wheels, do not remove these screws.

Otherwise, the leakage of air will affect sound quality.

Bottom

FRONT

7°

0°

7°

Pole socket

Subwoofer Speaker to be installed Length of the pole

DXS18XLF(-D)

Weight: 26 kg or less

Height: 76.0 cm or less

(DZR15(-D) or smaller)

104 cm or less

DXS15XLF(-D)

Weight: 22 kg or less

Height: 64.5 cm or less

(DZR12(-D) or smaller)

82 cm or less

Weight: 18 kg or less

Height: 53.7 cm or less

(DZR10(-D) or smaller)

104 cm or less

• For more information about installing wheels and related pre-

cautions, refer to the corresponding manual for the wheels.

• Do not install any item other than the SPW-1 wheels.

35 mm

diameter

M20 screw

NOTE

Functions

Full range

Subwoofer

Functions

Rear Panel (for both Full-range Speakers and Subwoofers)

q USB terminal

For connecting a USB flash drive to save/load data.

w [LIMIT] indicator

Lights red when the limiter for protecting the speaker is

active. If the indicator remains on, lower the level of the

input signal.

e [POWER] indicator

Lights green when the power is on. Flashes green when

the protection function is active and the output is muted.

(“MUTED” appears on the HOME screen in the display at

this time.)

r Display

Shows the settings for various functions.

t Main knob

Turn the knob to move the cursor that appears in the dis-

play and change parameter values. Press the knob to

execute a setting.

y [ ] (Back) key

Press this key to move up the previous screen. Press and

hold the key to return to the HOME screen.

u [LEVEL] controls

Adjust the level that is input to the [INPUT] jacks.

i [INPUT] jacks

Combo jacks for line level input. Accept both XLR and

phone plugs.

o [THRU/OUTPUT] jacks

XLR output jacks. The output signal for channel 2 on full-

range speakers and both channels 1 and 2 on subwoof-

ers can be switched using the [THRU/DSP OUT] switch.

On full-range speakers, channel 1 is fixed to [THRU].

!0 [THRU/DSP OUT] switch

Selects whether to output the signals from the input jacks

without processing ([THRU]) or to output the signals after

DSP processing ([DSP OUT]).

!1 Vents

A cooling fan is installed on the exhaust side. When the

speaker is in use, take care that all of the vents are free

from obstruction.

NOTICE

When using a USB extension cable, use a cable that is no

longer than 1 m.

Available only on Dante models

(See page 9.)

DZR(-D) Series DXS-XLF(-D) Series

Functions

 Power section

!2 [AC IN] jack

Connect the supplied AC power cord here. First, connect

the power cord to this product, then insert the power cord

plug into the AC outlet. When removing the power cord,

perform this procedure in reverse order.

Insert the power cord fully until it is locked by the latching

lock mechanism (V-Lock).

Press the V-Lock latch to disconnect the power cord.

!3 Power switch

Turns the power supply on [–] or off [ ].

 Dante section (Dante models only)

!4 Dante jacks

These are etherCON jacks for a Dante network. Both jacks

are primary connections. They can be used for daisy

chain connections. For details, refer to the Reference

Manual.

!5 [LINK] indicator

Shows the Dante communication status. Lights green

when an Ethernet cable is connected correctly to the

Dante jack.

!6 [1G] indicator

Lights orange when the Dante network is functioning as

Gigabit Ethernet.

!7 [SYNC] indicator

Lights steady or flashes green according to the Dante

communication status, as shown in the following table.

WARNING

Use only the supplied power cord/plug.

CAUTION

Be sure to turn the power off before connecting or

disconnecting the power cord.

WARNING

A small amount of current flows even when the

power switch is off. If you will not use the speaker

for a long time, be sure to unplug the power cord

from the outlet.

• Depending on the timing when the power switch is turned on/

off, it might take up to 15 seconds for the power to turn on.

• When using multiple devices, we recommend turning each

device on one at a time. If multiple devices are turned on at the

same time, the devices might not start up correctly due to a

voltage drop at the power supply.

NOTE

Use STP (Shielded Twisted Pair) cables to prevent electromag-

netic interference. Make sure that the metal parts of the plugs are

electrically connected to the STP cable shield by conductive tape

or comparable means.

Steady

Operating normally as a word clock

slave

Continuously flashing

Operating normally as a word clock

master

Periodically flashing

one time

Incorrect word clock setting

Periodically flashing

two times

Dante network cable not connected

Periodically flashing

three times

Incorrect Dante network connection

!5!6 !6

NOTE

HOME Screen

The HOME screen appears when the power switch is turned on.

For details, refer to the Reference Manual on the Yamaha Pro Audio global website.

https://www.yamaha.com/proaudio/

Display Description

q UNIT ID, LABEL

Shows the UNIT ID and label that are used for Dante. Allows you to go to the DANTE SETUP screen to

configure and display Dante settings.

w Input Meter (ANA*)

(*IN on standard models)

Shows the input level of the analog signal.

e Input Meter (DNT)

Shows the input level of the Dante signal.

r MASTER Level Displays and sets the output level (Unit: dB).

t SP Output Meter Shows the output level.

y Protection

(THERMAL, MUTED)

Appears when the protection function is active. If the speaker is hot, THERMAL is displayed (and the out-

put level is reduced). If the conditions of the usage environment become even worse, MUTED is dis-

played (and the output signal is muted).

u PRESET Shows the preset No. and title of the currently selected preset. Allows you to store, recall, and edit sound-

related settings. E symbol is displayed when you edit a parameter.

i HPF Allows you to configure and display the high-pass filter frequency settings.

LPF Allows you to configure and display the low-pass filter frequency and POLARITY settings. is displayed

when the polarity is set to INVERTED.

o D-CONTOUR

Allows you to configure and display the D-CONTOUR mode settings.

D-XSUB Allows you to configure and display the D-XSUB mode settings.

!0 EQ Shows if the equalizer is ON or OFF. Allows you to configure the EQ settings while checking the frequency

characteristics.

!1 DELAY Allows you to configure and display delay settings.

!2 CARDIOID Allows you to configure and display the cardioid mode settings.

!3 ROUTER Allows you to configure the routing of the audio signal.

!4 UTILITY Allows you to configure and display the following settings.

- PANEL SETUP: Configures display brightness, contrast, and display/indicator auto off settings.

- PANEL LOCK: Configures misoperation prevention setting, saves/loads PIN CODE.

- DEVICE BACKUP: Saves/loads configuration data.

- DANTE SETUP : Configures and displays Dante settings.

- NETWORK : Configures and displays network settings.

- DEVICE INFORMATION: Displays the status and information unique to this product.

- INITIALIZE: Performs initialization.

- LOG: Displays recorded logs. Saves logs to USB flash drive.

- UPDATE FIRMWARE: Update the main firmware and Dante module firmware.

Full range

Subwoofer

 Example (Dante models)

Full range

 Example (Dante models)

Subwoofer

Dante model

Full range

Subwoofer

Full range

Subwoofer

Dante model

 HPF i on page 10

Configure the high-pass filter frequency settings.

 D-CONTOUR o on page 10

Switch a D-CONTOUR preset.

 EQ !0 on page 10

Configure the equalizer settings. The total gain character-

istics for a 6-band equalizer are displayed on a graph.

 ROUTER !3 on page 10

Configure the routing of the audio signal. Set for the rout-

ing point of the signal you want to output. You can set the

input and output levels by selecting INPUT or OUTPUT

and going to the INPUT or OUTPUT level setting screen.

 LPF i on page 10

Configure the low-pass filter frequency settings.

 D-XSUB o on page 10

Switch a low range characteristic.

 DELAY !1 on page 10

Allows you to switch the delay ON or OFF, and configure

three types of delay settings. Editing one type will affect

the settings for the other types.

 PRESET u on page 10

Allows you to store up to eight sound-related settings.

When using the DZR and DXS-XLF series, simply recalling

the preset of the speaker model to be used optimizes the

corresponding settings. Recalling INITIAL DATA allows

you to return to the factory settings.

For details, refer to the Reference Manual on the Yamaha Pro Audio global website.

https://www.yamaha.com/proaudio/

Full range

Subwoofer

Main Menus and Examples of Screens

Full range

Subwoofer

Screen Operations

Basic Operations

1. Turn the main knob to select an item. The selected item is highlighted.

An arrow > on the right indicates that there is sub menu.

2. Press the main knob to execute a selection.

3. Repeat steps 1 and 2 until you reach the edit parameter screen.

To edit parameters that have selected values, turn the main knob to select a value. The

value will not be updated and the sound will not change until you press the main knob to

execute the change.

To edit parameters that have continuous values, turn the main knob to change the value

for that parameter. The value is changed in real time as you turn the knob.

4. For parameters with selected values, press the main knob to execute the edited value.

Press the [ ] (back) key to move up to the previous screen. (Press and hold it to return to the HOME screen.)

Using a USB Flash Drive to Save/Load Data

The setting data for this product can be saved to a USB flash drive. This function is convenient when using the same

settings for many speakers.

Saved files are categorized into full-range speakers and subw oofers; the two types of files are not compatible.

 Save to USB flash drive (SAVE)

On the HOME screen of the speaker that is the data source, select UTILITY  DEVICE

BACKUP  SAVE TO USB. Follow the on-screen instructions to save the data.

 Load from USB flash drive (RESTORE)

On the HOME screen of the speaker to which the data will be loaded, select UTILITY 

DEVICE BACKUP  RESTORE FROM USB. Follow the on-screen instructions to load the

data.

Full range

Subwoofer

Main knob

[ ] (Back) key

Basic Settings

Basic Systems for Analog Connections



System example 1

This example uses only DZR and DXS-XLF series speakers.

 System example 2

This example uses only DZR and DXS-XLF series speakers.

Full range

Subwoofer

Analog Mixer

A FOH (L) A FOH (R)

(L+R)

[THRU]

MONI1-1 MONI1-2

[THRU]

MONI2-1 MONI2-2

[THRU]

• Individual analog connections on

each bus

• For the same sound source, use

[THRU/DSP OUT] switch to set to

[THRU]

• Recalling a preset at A

• Recalling a preset at B

Analog Mixer

(L)

C FOH

(L)

C FOH

(R)

Side

(R)

Side

(L)

(R)

[THRU] [THRU]

MONI1 MONI2 MONI3 MONI4-1 MONI4-2

[THRU]

• Individual analog connections on

each bus

• For the same sound source, use

[THRU/DSP OUT] switch to set to

[THRU]

• Recalling a preset at C

• Recalling a preset at D

Dante Connection

Basic Systems for Dante Connections

 Example of a 15-unit system, including switches

This example uses only DZR-D and DXS-XLF-D series speakers.

Dante Connection

For Dante models (DZR-D and DXS-XLF-D series speakers), you can use Dante devices and Dante Controller to

make patches. If you connect to a TF series, CL series, or QL series Yamaha digital mixing console, you can make

patches without using Dante Controller. In particular, the TF series has a Quick Config function that can be config-

ured easily to make patches automatically.

For details, refer to the Reference Manuals for DZR(-D) and DXS-XLF(-D) series speakers. (For details about how to

use Yamaha digital mixing consoles, refer to the manual for each individual model.)

https://www.yamaha.com/proaudio/

(L)

MONI1 MONI2 MONI3 MONI4

Configuration with Dante

Models

Keep a single daisy chain to

within 10 units, including

switches. If a daisy chain

exceeds 10 units, communica-

tion latency within the network

will increase and the audio

might cut out. In such cases,

use an L2 switch (that supports

Gigabit Ethernet) to create

branches in the network.

I/O rack

Side (L) FOH (L) FOH (R) Side (R)

(R)

L2 switch

Digital mixer

Cardioid Mode Settings

Arrange DXS-XLF(-D) series speakers (hereinafter referred to as DXS-XLF(-D)) so that they are facing in opposite

directions. Configure the cardioid mode setting on the screen. (See !2 on page 10.) All other settings (LEVEL,

POLARITY, LPF etc.) should be configured to the same settings.

 Example arrangement with two units side by side

• Use the same DXS-XLF(-D) model, and the same input signal. You can also set the [THRU/DSP OUT] switch to [THRU] to use in a sequence

connection. See the example arrangements below.

• In order to maximize the cardioid characteristics, position the cabinets at least 1.2 m away from walls.

Subwoofer

NOTE

From the mixer

To the full-range

speakers

From

the mixer

To the DXS-

XLF(-D) on

the right

Audience

Stage

CARDIOID settings

From the

DXS-XLF(-D)

on the left

To the full-range speak-

ers (when full-range

speakers are placed

after subwoofers)

 Example arrangement

with three units side

by side

CARDIOID settings

Audience

Stage

From the mixer

To the DXS-XLF(-D)

on the right

From the DXS-XLF(-D)

on the left

From the

DXS-XLF(-D)

in the center

From

the mixer

To the DXS-

XLF(-D) in

the center

Rotatable Horn

When shipped from the factory, the directivity of DZR(-D) series speaker in a vertical orientation is the setting which

makes the sound expand in a horizontal direction, and inhibits or narrows the sound in a vertical direction. We rec-

ommend changing the directivity by rotating the horn when you want to install the DZR(-D) series speaker horizon-

tally or when you want to use them as a floor monitor and broaden the directivity.

1. Using a 2.5 mm hexagonal wrench, remove all fixing screws (DZR10(-D): six total) on the grille, and remove the grille from

the speaker.

2. Using a No. 2 Phillips head screwdriver, remove all screws installed on the horn and pull the horn out from the speaker.

3. Rotate the horn 90 degrees, and re-install the horn to the speaker, reversing the steps above.

• Make sure not to push the screws too strongly with the Phillips head screwdriver. This may cause the nuts inside the cabinet to fall off.

• If the horn cannot smoothly be pulled out, hook the notches using a flat-bladed screwdriver, and pull out.

Full range: DZR15(-D), DZR12(-D), and DZR10(-D)

NOTE

Screws (eight total)

Notch

Vertical

Rotate 90°

Horizontal

Installation Examples

Suspended Installation Using Eye Bolts



Suspension angle

Make sure to use eye bolts within a range of 0 to 45 degrees from a right angle.

 Suspended installation example

CAUTION

• Before doing any installation or construction work, consult with your Yamaha dealer.

• The installation should be checked thoroughly at regular intervals. Some fittings may deteriorate over extended periods of

time due to wear and/or corrosion.

• When choosing the installation location, suspension wire and mounting hardware, make sure all are strong enough to

support the weight of the speaker.

• Make sure to take precautionary measures using wires to prevent the speaker from falling down in the event of an installa-

tion failure.

• When installing the wire to the wall, install it higher than the wire’s attachment point on the speaker, with as little slack as

possible. If the wire is too long, and the speaker happens to fall, the wire may snap as a result of too much strain.

• Make sure to use eye bolts according to the standards and safety regulations in your area.

Yamaha cannot be held responsible for damage or injury caused by insufficient strength of the support structure or

improper installation.

Full range

Attach commercially available long eye bolts (30–50 mm in

length) to the screw holes for the eye bolts (e on page 7). The

screw diameter for DZR315(-D), DZR15(-D), and DZR12(-D) is

M10, and the screw diameters for DZR10(-D) are M10 and M8.

Keep in mind that you will need two or more rigging points.

 Securing the eye bolts

Insert the eye bolts through the washers when attaching

them.

• The screw holes for eye bolts go through the cabinet wall.

• When using eye bolts, remove the flat-head screws tightened at

the time of factory shipment. When not using eye bolts, tighten

the flat-head screws in order to prevent air leaks.

NOTE

Apply thread-

locking fluid

to the eye bolt

Bottom

0°

45°

Max. 45°

M10 eye bolt

Pullback point

Side

Rear

Max. 45°

Installation Examples

 Incorrect examples for suspended installation

Do not suspend the eye bolts as shown in the illustrations below.

Installation Using a Dedicated U-bracket

By using the separately sold Yamaha UB-DZR series U-bracket, you can expand the installation possibilities. For instructions on

installing the U-bracket, refer to the corresponding manual for the UB-DZR series.

 Examples

The UB-DZR series can be used together with separately sold optional brackets, such as the Yamaha BBS251 Baton Bracket.

Prohibited Prohibited

More than 45° from

a right angle

More than

45°

More than

45°

Only one

suspension point

NOTE

Optional Accessories (sold separately)

Troubleshooting

If any specific problem should persist, please contact your Yamaha dealer.

Speaker Cover U-bracket Wheels

DZR315(-D) SPCVR-DZR315 — —

DZR15(-D) SPCVR-DZR15 UB-DZR15H, UB-DZR15V —

DZR12(-D) SPCVR-DZR12 UB-DZR12H, UB-DZR12V —

DZR10(-D) SPCVR-DZR10 UB-DZR10H, UB-DZR10V —

DXS18XLF(-D) SPCVR-DXS18X — SPW-1

DXS15XLF(-D) SPCVR-DXS15X — SPW-1

Symptom Possible causes Possible solution

Power does not come on.

Time between turning the power on/off is too

short.

Wait about 20 seconds after turning the

power off before turning it back on again.

No sound.

Routing is not appropriate.

On the HOME screen, if there is a signal in the

INPUT meter but no signal in the SP Output

Meter, check if the signal is routed to SP OUT

under ROUTER in the settings.

Level is low in DSP.

Check the INPUT level under ROUTER in the

settings, and raise it if it is too low.

No sound, or

intermittent sound.

Too many Dante devices in the daisy chain

for the current latency settings.

With the default setting (1 msec), a single

daisy chain can have up to 10 units. When

connecting more than 10 units, use an L2

switch (that supports Gigabit Ethernet) to cre-

ate branches in the network.

Volume becomes low sud-

denly.

Protection function is active because the

amp is too hot, triggering the limiter.

In such cases, THERMAL is displayed on the

HOME screen. To prevent the speaker from

getting hotter, improve the ventilation around

the rear panel and shield the panel from

direct sunlight.

Sound is interrupted sud-

denly.

Protection function is active because the

amp became hotter, triggering the mute

function.

In such cases, MUTED is displayed on the

HOME screen and at the same time the

[POWER] indicator flashes. To prevent the

speaker from getting hotter, improve the venti-

lation around the rear panel and shield the

panel from direct sunlight.

The speaker units are damaged.

If there is no sound even though MUTED is

not displayed on the HOME screen and there

is a signal in the SP Output Meter, the speaker

units might be damaged. Please contact your

Yamaha dealer.

Display goes off after a few

moments.

The protection function for the display is

active.

Press either the main knob or the [ ]

(back) key to return to the normal display.

Dante model

151

General Specifications

0 dBu is referenced to 0.775 Vrms.

*1: Measured peak SPL with pink noise @1 m.

*2: Total peak power of individual outputs (AC 120 V, 25°C). This value was measured at minimum load impedance, with protection released.

DZR315(-D) DZR15(-D) DZR12(-D) DZR10(-D)

System Type 3-way, Bi-amped

powered speaker,

Bass-reflex

2-way, Bi-amped powered speaker, Bass-reflex

Frequency Range (-10 dB) 31 Hz – 20 kHz 34 Hz – 20 kHz 39 Hz – 20 kHz 44 Hz – 20 kHz

Coverage Angle

H75° × V50°

H90° × V50°

(Rotatable)

H90° × V60°

(Rotatable)

H90° × V60°

(Rotatable)

Crossover Frequency, Type 700 Hz (FIR-X)

2.5 kHz (Passive)

1.7 kHz (FIR-X) 1.8 kHz (FIR-X) 1.8 kHz (FIR-X)

Maximum SPL

143 dB SPL 139 dB SPL 139 dB SPL 137 dB SPL

Transducer LF 15" Cone,

3" Voice coil,

Neodymium magnet

15" Cone,

3" Voice coil,

Neodymium magnet

12" Cone,

3" Voice coil,

Neodymium magnet

10" Cone,

3" Voice coil,

Neodymium magnet

MF 8" Cone,

1.5" Voice coil,

Ferrite magnet

—

HF 2" Voice coil, 1" Throat compression driver, Titanium diaphragm, Neodymium magnet

Enclosure Material, Finish, Color Plywood, Durable polyurea coating, Black

Floor Monitor Angle — 50° Symmetrical 50° Symmetrical 50°

Dimensions

(W × H × D, with rubber feet)

550 × 897 × 520 mm 450 × 761 × 460 mm 410 × 646 × 394 mm 315 × 537 × 345 mm

Weight 41.6 kg 25.2 kg 21.4 kg 17.9 kg

Handles

Aluminium die-cast, Side × 2

Aluminium die-cast,

Top × 1, Side × 1

Pole Socket — Ø35 mm × 2 (0° or -7°)

Rigging Points M10 × 16 M10 × 12 M10 × 8, M8 × 2

Amplifier Type Class-D

Power Rating Dynamic

2000 W (LF:1000 W, MF/HF: 1000 W)

Continuous 1300 W (LF: 920 W, MF/HF: 380 W)

Cooling Fan cooling, Variable speeds.

DSP, AD/DA 96 kHz processing with 96 kHz AD/DA and FIR filter

Connectors Analog IN Combo × 2, Line level (Maximum +24 dBu), Input impedance: 20 kΩ

Analog OUT XLR3-32 × 2, CH1: THRU (fix), CH2: THRU or DSP OUT

Dante

(-D model only)

etherCON CAT5e × 2 (Daisy chain), 2 IN / 2 OUT (Fs: 44.1k, 48k, 88.2k, 96k) and

Remote control, 1000BASE-T

USB USB 2.0 host: 5 V 500 mA, for USB memory data save/load

AC IN IEC AC inlet × 1 (V-Lock)

Idle Power Consumption 45 W

1/8 Power Consumption 150 W

Optional

Accessories

U-bracket

—

UB-DZR15H,

UB-DZR15V

UB-DZR12H,

UB-DZR12V

UB-DZR10H,

UB-DZR10V

Cover SPCVR-DZR315 SPCVR-DZR15 SPCVR-DZR12 SPCVR-DZR10

General Specifications (English only)

La page est en cours de chargement...

Yamaha DZR10 Le manuel du propriétaire

Marque: Yamaha

Modèle: DZR10

Catégorie: Égaliseurs audio

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Yamaha DZR10 Owner's manual

Yamaha DZR10 Le manuel du propriétaire

Ce manuel convient également à

Yamaha DZR10 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents