Haier HLC26R1 - 26" LCD TV Le manuel du propriétaire

Please READ this manual carefully before

operating your TV, and retain it for future

reference.

TFT-LCD TV/DVD Combo

OWNER S MANUAL'

MODEL :S

R

HLC32R1

HLC26R1

2 TV LCD-TFT

Warning

RISK ELECTRIC SHOCK

DO NOT OPEN

CAUTION

!

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

The lightning flash with arrowhead symbol, within an

equilateral triangle is intended to alert the user to the

presence of uninsulated dangerous voltage within the

product’s enclosure that may be of sufficient magnitude

to constitute a risk of electric shock.

The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in

the literature accompanying the appliance.

!

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO

RAIN OR MOISTURE.

CAUTION: TO PREVENT ELECTRIC SHOCK DO NOT USE THIS POLARIZED PLUG WITH AN

EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES

CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.

CAUTION: These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric

shock, do not perform any servicing other than that contained in the operating instructions unless you are qualified

to do so.

Important Safety Instructions

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.

8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with

one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the

third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for

replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the

point where they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer,

or sold with the apparatus. When a cart is used, use caution when moving the cart/

Apparatus combination to avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or when unused for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged

in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the

apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15)The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases,

shall be placed on the apparatus.

16)The mains plug or appliance inlet is used as the disconnect device, remain it readily operable during the

apparatus normal use.

Class I apparatus shall be connected to a mains socket outlet with a protective earthing connection.

LASER SAFETY: This unit employs a laser. Only a qualified service person should remove the cover or attempt

to service this device, due to possible eye injury.

CAUTION: USE OF ANY CONTROLS, ADJUSTMENTS, OR PROCEDURES OTHER THAN THOSE SPECIFIED

HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

CAUTION: VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK DEFEATED.

DO NOT STARE INTO BEAM.

LOCATION: INSIDE, NEAR THE DECK MECHANISM.

Owner s Manual 3

Safety Instructions

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the

FCC Rule. These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, use and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However there is no

guarantee that interference will not occur in particular installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by turning the equipment off and on, the user is encourage to

try to correct the interference by one or more of the following measures:

*Reorient or relocate the receiving antenna.

*Increase the separation between the equipment and receiver.

*Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

*Consult the dealer or an experienced radio/TV technician for help.

This device compiles with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may be not cause harmful interference.

(2) this device must accept any interference received, including interference that may cause undesired

operation.

FCC CAUTION:

To assure continued compliance and possible undesirable interference, the provided ferrite cores must be

used when connecting this LCD display to video equipment; and maintain at least 40cm spacing to other

peripheral device.

CANADIAN NOTICE:

This Class B digital apparatus compiles with Canadian ICES-003.

FCC STATEMENT

Energy Star compliant

By being Energy Star compliant you are assured that your Haier model is helping the environment by using less

energy while saving you money. ENERGY STAR is a joint program of the U.S. Environmental Protection Agency and

the U.S. Department of Energy promoting energy efficiency.

SAVE THESE INSTRUCTIONS

Thank you for purchasing the Haier product. This easy-to-use manual will guide you in getting the best use of your

product. Remember to record the model and serial number. They are on label in back of the unit.

Model number

serial number

Date of purchase

Staple your receipt to your manual. You will need it to obtain warranty service.

4 TV LCD-TFT

Safety Instructions

Introduction

Owner s Manual 5

Contents

War ning . . . . . . . ..... .... .... . . . . . . . . . . . . . . . . . . . . . .

Safe ty Ins truc tion s . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Introduction

Cont rols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .... .... ..

Conn ecti on Opt ions . . . . . . . . . . . . . . . . . . . . . . .... ....

Remote control . ............ . . . . . . . . .........

Installation

Acce ssor ies . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. .... ..

Antenna Connection . . . . . . . . . . ..........................

Conn ecti ng a VCR . . . . . . . . . . . . . . . . . . . . . .... .... ...

External A/V Source Setup . . . . .. . . . . ..................

Conn ecti ng a DVD p laye r . . . . . .... .. . . . . . . . . . . . . .

Connecting a DTV(digital TV) ..............................

Connecting digital audio output . . . . . . . . . . . . . . . . .

Conn ecti ng a com pute r. . . . . . . . . . . . . . . . . . . . . . . .

Monitor Out Setup. . . . . . . . . . . . . . . . . . . . .... .... .... .

HDMI a nd DVI i nput . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Cable sample......................................................

Connecting Headphones . . . . . . . . . . . . . . . . . . . .....

Power source................ . . . . . . . . . . . . . . . . . . . . . .

Removing the table stand and installing a

wall mount bracket

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Operation

Switching On/Off the TV set . . . . . ... . . . . . . . . . . ....

Choose the Menu Language . . . . ..... ....................

Choose the input source......................................

Channel Menu

Channel Scan............... . . . . . . . . . . . . . . . . . . . . . . .

Chan nel Sk ip.. .... . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Sele ct the d esir ed pro gram . . . . . . . . . . . . . . . . . . . . .

Sele ct the d esir ed sou nd. . . . . . . . . . . . . . . . . . .. . . .

Mute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Video Menu

How to select picture mode..................................

How to customize your own picture status .............

Set. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

.

. . . .........

PC

2

3

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

Audio Menu

How to select audio mode....................................

.

How to customize your own audio status ...............

SAP Broadcasts Setup........................................

.

Function Menu

Menu Language...................................................

OSD Timeout.......................................................

OSD Transparency...............................................

Screen Mode.......................................................

Blue Screen.........................................................

DPMS.................................................................

Time zone setting.................................................

Date /Time setting................................................

Sleep Timer setting..............................................

DTV Caption Style................................................

Lock Menu

Parental Control rating and categories...................

Lock setup...........................................................

Other Functions

Brie f Info . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .... .... ....

Usin g the Gu ide. . . . . . . . . . . . . . . . . . . . . . . . .... .... ...

Quick program view..............................................

CC (Closed Caption Display) . . . . . . . . . . . . . ... . .. .

USB Input............................................................

DVD Operation

Basic Playback....................................................

Advanced Playback..............................................

Special Function Playback....................................

DVD System Setup...............................................

Playable Discs.....................................................

Discs Protection and DVD Characteristics..............

Maintenance . . .. .. .. . . . . . . . . . . . . . . . . . . . . . . . . . .

Product Specification . . . . . . . . . . . . . . . . . . . . . . .

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Warranty ............................................................

23

31

24

25

26

27

28

30

31

32

34

35

36

37

38

39

40

41

TV Side panel controls and connections

This is a simplified representation of the TV front panel, side panel control buttons and side inputs.

Introduction

6 TV LCD-TFT

Controls

1.MENU: Menu display. Press to access the on-screen menu display

2.INPUT: Press to access the input source mode. Press repeatedly to change the source to the one you want to

watch. In the MENU screen, the INPUT button serves as the ENTER button.

3.VOL +/-: Press to adjust the volume. In the MENU screen, these buttons serve as left/right buttons.

4.CH +/- : Press to scan through channels. To scan quickly through channels, press and hold down

either +/- . In the MENU screen, these buttons serve as up/down buttons.

5.POWER: Press to turn on and off the TV.

6.USB input: Connect a USB flash drive to view JPEG images or listen to MP3 songs.

7.Av2 AUDIO IN: Connect the audio L/R cables from the video signal source to these jacks.

8.AV2 VIDEO IN: Connect the composite video cable from an external signal source to this jack.

9.Headphone jack : Headphone audio output terminal.

10.HDMI IN: Connect a HDMI device to receive digital audio and uncompressed digital video signals.

11. Remote Sensor Receivers IR signals from the remote control.

Do not put anything near the sensor ,which may block the remote control signal.

L-AUDIO-R

HDMI4 INHDMI3 IN USB

VIDEO2 IN

VIDEO

MENU INPUT VOL+ VOL- CH+ CH- POWER

STOP

Press to stop the DVD .

PLAY/PAUSE

Press to play the DVD program , and press again to pause the DVD program.

OPEN/CLOSE:

Press to open the disc tray, and press again to close the tray.

disc

DVD panel controls

Label Towards Back

Insert DVD with label towards

back(Silver "shiny" side

facing towards you.)

DVD slot load

Back panel connections

Introduction

Owner s Manual 7

Connection Options

2

1

Y

Pb

Pr

L

R

L L

R R

VIDEO

S-VIDEO

VGA

VGA AUDIO

AUDIO

L

R

DVI AUDIO

AUDIO

2

L

R

AUDIO

COMPONENT IN

VIDEO IN

1

AUDIO OUT

VGA IN

HDMI IN

ANT IN

OPTICAL OUT

1. Digital Audio Output: Connect various types of digital audio equipment.

NOTE: In standby mode, these ports will not work.

2. DVI Audio In: When using a DVI to HDMI adapter, connect the audio signal to these jacks.

3. Antenna Input: Connect cable or antenna signals to the TV, either directly or through your cable box.

4. HDMI In: Connect a HDMI device to receive digital audio and uncompressed digital video.

5.VGA Audio In: Connect the audio L/R cables from a computer to this jack.

6.VGA Video In: Connect a video cable from a computer to this jack.

7. VIDEO In: Connect the video signal from a video device to this jack.

8. Component Video In: Connect a component video device to these jacks.

9. AUDIO In: Connect the audio L/R cables from the video signal source to these jacks.

10. S-VIDEO In: Connect the S-Video cable from an external signal source to this jacks.

11. COMPONENT AUDIO In: Connect the audio L/R cables from the component video signal source to these jacks.

12. AUDIO In: Connect the audio L/R cables from the S-Video signal source to these jacks.

13. AUDIO Out: Connect the audio L/R cables to your audio equipment.

Introduction

Remote control

8 TV LCD-TFT

1.Power Press to turn on and off the TV

2.USB Press to switch input source to USB in

3.GUIDE Display the guide when you are watching analog or digital

channels

4.CCD(closed caption) closed caption option

5.PICTURE Press repeatedly to cycle through the available picture modes.

6.AUDIO Press to cycle through different sound settings

7.INPUT Show the input source

8.MUTE Switches the sound on or off

9.VOLUME UP/DOWN Press to adjust the volume

10.MENU Press to open the on-screen menu

11.Thumbstick(Up/Down/Left/Right)

Allows you to navigate the on-screen menus and adjust the system settings

to your preference.

12.SLEEP button Press to display the sleep timer option

13.DVD/USB PLAY/PAUSE

14.DVD Open/close

15.DVD/USB FAST FORWARD

16.DVD/USB FAST REVERSE

17.DVD CALL

18.DVD MENU

19.DVD SEARCH

20.DVD ANGLE

21.DVD Mode

22.CH.LIST Open the channel list in TV

23.MTS/SAP Select MONO, STEREO, SAP in NTSC system

24.FAVORITE Open the favourite channel list in TV

25.ARC Select the aspect ratio

26.Number buttons Press to change a channel

27. button Press to select digital channels. For example, to enter

“54-3”, press “54”, “ ” and “3”

28.RECALL Press to jump back and forth between two channels

29.CHANNEL UP/DOWN Press to scan between the last two channels,

press and hold down either +/-

30.EXIT Clears all on-screen displays and returns to TV viewing from any

menu

31.ENTER Accesses the highlighted item in the on-screen menu

32.DISPLAY Press to display the TV status information on the top of the

TV screen

33.DVD/USB STOP

34.DVD/USB REPEAT

35.DVD/USB Previous Chapter

36.DVD/USB Next Chapter

37.DVD AUDIO Mode

38.DVD SETUP

39.DVD PROGRAM

40.DVD SUBTITLE

Select a

OPEN/CLOSE

PLAY/PAUSE

REV

D.MENU

SEARCH

D.CALL

ANGLE

D.AUDIO

SUBTITLE

ENTER

STOP REPEAT

PREV NEXT

SETUP

PROGRAM

USB

GUIDE

INPUT

MUTE

VOL CH

MENU

SLEEP DISPLAY

EXIT

RECALL

PICTURE AUDIO ARC FAVORITE

CCD MTS/SAP CH.LIST

DVD

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

39

40

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

The remote control cannot be operated unless the batteries are properly loaded.

When using the remote control, aim it at the remote sensor on the TV.

ANT IN

Over-the-air TV reception quality will depend on your antenna type, antenna location and antenna positioning.

External Equipment Connections

Antenna Connection

Multi-family Dwellings/Apartments

(Connect to wall antenna socket)

Wall Antenna

Socket

Single-family Dwellings /Houses

(Connect to wall jack for outdoor antenna)

Outdoor

Antenna

VHF Antenna

UHF Antenna

Turn clockwise to tighten

RF Coaxial Wire (75 ohm)

Bronze Wire

Be careful not to bend the bronze wire

when connecting the antenna.

Bronze Wire

To improve the picture quality in a poor signal area,

please purchase a signal amplifier and install properly.

If the antenna needs to be split for two TV`s, install a

2-Way Signal Splitter in the connections.

To install the antenna properly please contact a

professional in your area.

Installation

Accessories

Remote control Owner`s manual Alkaline battery(AAA) 2

Owner s Manual 9

Please READ this manual carefully before

operating your TV, and retain it for future

reference.

TFT-LCD TV

OWNER S MANUAL'

MODEL:S

HL26K

HL32K

R

PLAY/PAUSE

REV

REPEAT

GUIDE

MTS/SAP

CCD ARC

FREEZE

ENTER

STOPUSB REC

PREV NEXT

CH.LIST

FAVORITE

TV

STB

INPUT

MUTE

VOL CH

MENU

SLEEP DISPLAY

EXIT

RECALL

PICTURE AUDIO PC HDMI

CABLE VCR AUD

DVD

2

1

Y

Pb

Pr

L

R

L L

R R

VIDEO

S-VIDEO

VGA

VGA AUDIO

AUDIO

L

R

DVI AUDIO

AUDIO

2

L

R

AUDIO

COMPONENT IN

VIDEO IN

1

AUDIO OUT

VGA IN

HDMI IN

ANT IN

OPTICAL OUT

Installation

10 TV LCD-TFT

Connecting a VCR

NOTE: All cables shown are not included with the TV.

There are several ways to connect your television,

depending on the components you want to connect and

the quality of the signal you want to achieve. The

following are examples of some different ways to connect

your TV with different input sources.

External Equipment Connections

Choose Your Connection

To avoid picture noise (interference), leave an adequate

distance between the VCR and TV.

Connection Option 1

Set VCR output switch to channel 3 or 4 and then tune

the TV to the same channel number.

Connection Option 2

1. Connect the audio and video cables from the VCR's

output jacks to the TV input jacks, as shown in the figure.

When connecting the TV to VCR, match the jack colors

(Video = yellow, Audio Left = white, and Audio Right = red).

If you connect a S-VIDEO output from VCR to the

S-VIDEO input, the picture quality is improved;

compared to connecting a regular VCR to the Video input.

2. Insert a video tape into the VCR and press PLAY on

the VCR. (Refer to the VCR owner`s manual.)

3. Select the input source with using the

INPUT button on the remote control, and

then press / button to select the source,

press ENTER button to confirm.

2

1

Y

Pb

Pr

L

R

L L

R R

VIDEO

S-VIDEO

VGA

VGA AUDIO

AUDIO

AUDIO AUDIO

L

R

DVI AUDIO

AUDIO

2

L

R

AUDIO

COMPONENT IN

VIDEO IN

1

AUDIO OUT

VGA IN

HDMI IN

ANT IN

OPTICAL OUT

2

1

Y

Pb

Pr

L

R

L L

R RVIDEO

S-VIDEO

VGA

VGA AUDIO

AUDIO

L

R

DVI AUDIO

AUDIO

2

L

R

AUDIO

COMPONENT IN

VIDEO IN

1

AUDIO OUT

VGA IN

HDMI IN

ANT IN

OPTICAL OUT

How to connect

1. Connect the DVD video outputs (COMPONENT) to

the Y Pb Pr jacks on the TV and connect the DVD audio

outputs to the YPbPr Audio IN jacks on the TV, as

shown in the figure.

2. If your DVD only has an S-VIDEO output jack,

connect this to the S-VIDEO input on the TV. as shown

in the figure.

Note

If your DVD player does not have component video

output, use S-Video.

How to use

1. Turn on the DVD player, insert a DVD .

2. Use INPUT button on the remote control to select

component mode.

3. Press PLAY button on external equipment for

program play.

4. Refer to the DVD player's manual for operating

instructions.

disc

External Equipment Connections

How to connect

Connect the audio and video cables from the external

equipment's output jacks to the TV input jacks, as shown

in the figure.

When connecting the TV to external equipment, match the

jack colors (Video = yellow, Audio Left = white, and Audio

Right = red).

How to use

1. Select the input source with using the INPUT button on

the remote control.

2. Press / button to select the desired source.

3. Press ENTER button to confirm.

4. Operate the corresponding external equipment.

Video Game Set

Camcorder

Component Input ports

To get better picture quality, connect a DVD player to the

component input ports as shown below.

Installation

Component ports

on the TV

Video output ports

on DVD player

Y Pb Pr

Y B-Y R-Y

Y Cb Cr

Y P P

BR

External A/V Source Setup

Connecting a DVD player

Owner s Manual 11

2

1

Y

Pb

Pr

L

R

L L

R R

VIDEO

S-VIDEO

VGA

VGA AUDIO

AUDIO

L

R

DVI AUDIO

AUDIO

2

L

R

AUDIO

COMPONENT IN

VIDEO IN

1

AUDIO OUT

VGA IN

HDMI IN

ANT IN

OPTICAL OUT

2

1

Y

Pb

Pr

L

R

L L

R RVIDEO

S-VIDEO

VGA

VGA AUDIO

AUDIO

L

R

DVI AUDIO

AUDIO

2

L

R

AUDIO

COMPONENT IN

VIDEO IN

1

AUDIO OUT

VGA IN

HDMI IN

ANT IN

OPTICAL OUT

Digital Set-top Box

This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if you do receive

Digital signals from a digital set-top box or other digital external device, refer to the figure as shown below.

This TV supports HDCP (High-bandwidth Digital Contents Protection) protocol for Digital Contents (480p,720p,1080i).

How to connect

Use the TV`s COMPONENT , VGA or HDMI

jack for video connections, depending on

your set-top box connector. Then, make

the corresponding audio connections.

How to use

1. Turn on the digital set-top box. (Refer to the

owner`s manual for the digital set-top box.)

2. Use INPUT on the remote control to select

COMPONENT , VGA or HDMI source.

Send the TV`s audio to external audio equipment (stereo

system) via the Digital Audio Output (Optical) port.

How to connect

1. Connect one end of an optical cable to the TV Digital

Audio(Optical) Output port.

2. Connect the other end of the optical cable to the digital

audio (optical) input on the audio equipment.

See the external audio equipment instruction manual for

operation.

Note

When connecting with external audio equipments, such

as amplifers or speakers, please turn the TV speakers off.

Connecting a digital audio output

External Equipment Connections

Connecting a DTV(digital TV)

Installation

Signal

480i

480p

720p

1080i

1080p

COMPONENT

HDMI

Yes

HDMI

12 TV LCD-TFT

Caution: Do not look into the optical output

port. Looking at the laser beam may damage

your vision.

!

2

1

Y

Pb

Pr

L

R

L L

R RVIDEO

S-VIDEO

VGA

VGA AUDIO

AUDIO

L

R

DVI AUDIO

AUDIO

2

L

R

AUDIO

COMPONENT IN

VIDEO IN

1

AUDIO OUT

VGA IN

HDMI IN

ANT IN

OPTICAL OUT

How to connect

1. To get the best picture quality, adjust the VGA graphics card to 1024x768 .

2. Use the TV`s VGA or DVI (Digital Visual Interface)Audio IN port for audio connections, depending on your computer

connector.

If the graphic card on the computer does not output analog and digital RGB simultaneously, connect only one of

either VGA IN or HDMI IN to display the VGA on the TV.

If the graphic card on the computer does output analog and digital RGB simultaneously, set the TV to either VGA or

HDMI ; (the other mode is set to Plug and Play automatically by the TV.)

3. Then, make the corresponding audio connection. If using a sound card, adjust the VGA sound as required.

How to use

1. Turn on the computer and the TV.

2. Use INPUT on the remote control to select VGA or HDMI source.

3. Check the image on your TV. There may be noise associated with the resolution, vertical pattern, contrast or

brightness in VGA mode. If noise is present, change the VGA mode to another resolution, change the refresh rate to

another rate or adjust the brightness and contrast on the menu until the picture is clear. If the refresh rate of the VGA

graphic card can not be changed, change the VGA graphic card or consult the manufacturer of the VGA graphic card.

Note

1.Use a DVI cable.

2.Avoid keeping a fixed image on the TV's screen for a long period of time. The fixed image may become permanently

imprinted on the screen.

3. The synchronization input form for Horizontal and Vertical frequencies is separate.

Resolution

Frame

frequency

(Hz)

VGA

SVGA

XGA

640x480

60Hz

800x600

60Hz

1024x768

60Hz

Mode

Resolution

External Equipment Connections

Installation

75Hz

Connecting a computer

Owner s Manual 13

75Hz

When the source device(DVD player or Set Top Box) supports HDMI

How To Connect

1. Connect the source device to HDMI port of this TV with an HDMI cable(not supplied with this product).

2. No separated audio connection is necessary.

How To Use

If the source device supports Auto HDMI function, the output resolution of the source device will be automatically

set to 1280x720p.

If the source device does not support Auto HDMI, you need to set the output resolution appropriately.

To get the best picture quality, adjust the output resolution of the source device to 1280x720p.

Select HDMI input source in input source option of Select Main source menu.

When the source device(DVD player or Set Top Box) supports DVI

How To Connect

1. Connect the source device to HDMI port of this TV with a HDMI-to-DVI cable(not supplied with this product).

2. A separated audio connection is necessary.

3. If the source device has an analog audio output connector, connect the source device audio output to DVI Audio

In port located on the left side of HDMI port.

How To Use

If the source device supports Auto DVI function, the output resolution of the source device will be automatically

set to 1280x720p.

If the source device does not support Auto DVI, you need to set the output resolution appropriately.

To get the best picture quality, adjust the output resolution of the source device to 1280x720p.

Press the INPUT button to select HDMI input source in input source option of Select Main source menu.

Installation

HDMI and DVI input

14 TV LCD-TFT

External Equipment Connections

HDMI Cable

(not supplied with the product)

HDMI to DVI Cable

(not supplied with the product)

Analog Audio Cable

(Stereo to RCA type)

(not supplied with the product)

Installation

Cable sample

Owner s Manual 15

HDMI4 INHDMI3 IN

TO USE AC POWER SOURCE

Use the AC polarized line cord provided for

operation on AC. Insert the AC cord plug into

a standard polarized AC outlet.

Note

Never connect the AC line cord plug to other

than the specified voltage. Use the

attached power cord only.

If the polarized AC cord does not fit into a non-

polarized AC outlet, do not attempt to file or cut

the blade. It is the user`s responsibility to have

an electrician replace the obsolete outlet.

If you cause a static discharge when touching

the unit and the unit fails to function, simply

unplug the unit from the AC outlet and plug it

back in. The unit should return to normal operation.

Polarized AC Cord Plug

AC Outlet

Wider Hole

and Blade

You can connect a set of headphones to your set if you wish to watch a

TV programme without disturbing the other people in the room.

Connecting Headphones

Note

Prolonged use of headphones at a high volume

may damage your hearing.

You will not receive sound from the speakers

when you connect headphones to the system.

Plug a set of headphones into the 3.5mm

mini-jack socket on the side panel of the set.

Installation

External Equipment Connections

16 TV LCD-TFT

Power source

Installation

Owner s Manual 17

Removing the table stand and installing a

wall mount bracket

Remove 4X M4 screws securing the

stand to the TV, then remove the stand.

Remove 5X M4 screws securing the

stand to the TV, then remove the stand.

Use 4X M6 screws to secure the wall

bracket (not supplied) to the back of your TV.

Use 4X M6 screws to secure the wall

bracket (not supplied) to the back of your TV.

HLC26R1

HLC32R1

Choose the Menu Language

When you start using your set for the first time, you must

select the language which will be used for displaying menus

and indications.

In the manual, the OSD (on screen display) may be

different from your TV`s, because it is just an example to

help you with the TV operation.

There are several options you might need to set up in order

for your TV to work properly. Read the instructions that

follow.

Initial Setup: Set according to the screen display.

Note

If the TV in power on , the screen show information

according the type of input signal . the information will

disappear. If there is no signal , No Signal will display

on the screen.

1. Choose TV Input and then press MENU button.

2. Press / button to selectFunction menu.

3. Press or ENTER button and then use / button to select

Language.

4. Press button to select language.

English Spanish or French

/

1 First, connect power cord correctly.

2 Select the viewing source by using INPUT button on

the remote control.

3 When finished using the TV, press POWER button on

the remote control. The TV reverts to standby mode.

4 If you intend to be away on vacation, disconnect the

power plug from the wall power outlet.

.

Change the picture source so you can watch your TV,

VCR, DVD, Cable , or any other devices that are

connected to your TV.

1. Press INPUT button to enter the Select Source menu

and then use / button to select the desired items

(TV, Video1, Video2, S-Video,Component1, Component2,

PC, HDMI1,HDMI2,HDMI3,HDMI4, ).

2. Press ENTER button to confirm .

DVD

Operation

Select Source

TV

Video1

Video2

S-Video

Component1

Component2

PC

HDMI1

HDMI2

HDMI3

HDMI4

DVD

Operation

Switching On/Off the TV set

Choose the Input source

18 TV LCD-TFT

Video

Audio

Channel

Lock

Function

Language English

OSD Timeout Short

OSD Transparency Middle

Screen Mode Normal

Blue Screen On

DPMS On

Time Setup

Closed Caption

Default

Select

/

Back

EXIT

This TV set has two methods to set channels, which are

respectively Channel Scan, Channel Skip.

In this section, how to use the remote control to set

channel is explained. You can also use buttons on the TV to

set channel.

Note

The Channel menu will be only operated in normal TV mode.

Channel menu

Operation

Owner s Manual 19

1. Press MENU button and then use / button to select

Channel menu.

2. Press /ENTER button to selectTuner.

3. Press button to selectCable or Antenna mode.

4. Press / button to selectChannel Scan.

5. Press /ENTER button to start searching.

6. To cancel searching, press EXIT button.

/

Note

When Antenna is selected, the TV will detect antenna

signals and will search for antenna TV (NTSC and

ATSC) channels available in your local area.

When Cable is selected, the TV will detect cable

company supplied signals and will search for cable TV

(NTSC, QAM modulated) channels available in your

Area.

Channel Scan

Status: Antenna

Analog Channels: 19

Digital Channels: 0

64%

Scanning

Video

Audio

Channel

Lock

Function

Channel

Channel Scan

Tuner Antenna

Channel Scan

Channel Skip

Channel Label

Select

/

BackScan

EXIT

ENTER

Cancel

EXIT

Channel Skip

1. Press MENU button and then use / button to select

Channel menu.

2. Press / ENTER button and then use / button to

select Channel Skip.

3. Press / button to select a channel, then press ENTER

button to toggle between and .

A skip channel is skipped when using / button to

browse the channels. A skip channel can be watch

by key-in the channel number or select by list.

Default un-scanned analog channels are skip.

Channel with a check icon is a skipped channel.

1

2

3

4

5

5-1

6

7

8

9

10

Analog

Digital KPIX-DT

Analog

Video

Audio

Channel

Lock

Function

Channel Skip

Channel Label Set

Select

/

BackSet

EXIT

ENTER

Channel Label

Allows you to name the channel that is selected.

Press /ENTER button to enter the submenu.

Then press / to select Channel Index and Channel

Label and / to select the position of the item that you

want to change, afterward press INPUT to input the

numbers and symbols and ENTER button to confirm.

Channel Index

Channel Label

Select

Back

EXIT

1

Operation

20 TV LCD-TFT

1

Also can enter channel number directly,eg:2-0.

.

Note

If skip is ON on one channel, press CH+/- button, the

channel will not appear.

2.

Using CH+/- buttons.

Press CH+ button to select a channel number in

number increasing direction.

Press CH- button to select a channel number in

number decreasing direction.

Select the desired sound

Press VOL-/+ buttons on the remote or the front of the

TV set to adjust the volume level. The range is 0~100.

When the volume buttons are pressed the volume level

is displayed automatically on the TV screen.

Mute

1 Press MUTE button on the remote control and

type face will display on the screen. At this time, the

sound of the TV set is turned off.

2 If you want to recover the sound, press MUTE

button again or directly press VOL+ button.

.

Volume

Select the desired program

La page est en cours de chargement...

Haier HLC26R1 - 26" LCD TV Le manuel du propriétaire

Ce manuel convient également à

Haier HLC26R1 - 26" LCD TV Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents