Briggs and Stratton 1687916-00 Le manuel du propriétaire
- Taper
- Le manuel du propriétaire
82V
LITHIUM-ION BATTERY CHARGER
Read all safety rules and instructions carefully before operating this tool.
Owner’s Manual
TOLL-FREE HELPLINE: 1-800-743-4115
www.briggsandstratton.com
82V Lithium-ion Battery Charger
1760263 (BSRC82)
82V Lithium-ion Battery Charger
1761122 (BSSC82)
Not for Reproduction
2
CONTENTS
Product Specications ......................................................................................................... 2
Important Safety Instructions .............................................................................................. 3
Symbols ............................................................................................................................... 5
Know Your Charger .............................................................................................................. 6
Operation ............................................................................................................................. 7
Maintenance ...................................................................................................................... 10
Troubleshooting................................................ ....................................................................11
Limited Warranty.................................................................................................................... 12
PRODUCT SPECIFICATIONS
COMPONENTS SPECIFICATIONS
Charger 82V Lithium-ion Battery Charger
Model BSRC82
Input 120V AC, 50/60Hz, 5A
Output 82V DC, 4A
Weight 3.3 lbs (1.5 kg)
Disclaimer: *Maximum initial battery voltage (measured without a workload) is 82 volts.
Nominal voltage is 72.
Charger 82V Lithium-ion Battery Charger
Model BSSC82
Input 120V AC, 50/60Hz, 2A
Output 82V DC, 2A
Weight 2.0 lbs (0.9 kg)
Not for Reproduction
3
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS – SAVE
THESE INSTRUCTIONS
DANGER – TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, CAREFULLY FOLLOW THESE
INSTRUCTIONS
Read and understand all instructions before using this product. Failure to follow all instructions
listed below may result in electric shock, re, and/or serious personal injury.
WARNING
FOR INDOOR USE ONLY.
CAUTION
Risk of Electric Shock.
Dry location use only.
CAUTION
RISK OF FIRE OR ELECTRIC SHOCK, DO NOT INTERCONNECT OUTPUT TERMINATIONS.
CAUTION
CHARGE ONLY RECHARGEABLE BATTERY PACK BSB2AH82, BSB4AH82, BSB5AH82,
OTHER TYPES OF BATTERIES MAY BURST CAUSING PERSONAL INJURY AND DAMAGE.
DANGER
RISK OF ELECTRIC SHOCK. DO NOT TOUCH UNINSULATED PORTION OF OUTPUT
CONNECTOR OR UNINSULATED BATTERY TERMINAL.
• SAVE THESE INSTRUCTIONS - This manual contains important safety and operating
instructions for battery charger BSRC82/BSSC82.
• Before using battery charger, read all instructions and cautionary markings on battery
charger, battery, and product using battery.
• To reduce the risk of re and electric shock, install in a temperature- and humidity-controlled
indoor area relatively free of conductive contaminants.
• Use of an attachment not recommended or sold by the battery charger manufacturer may
result in a risk of re, electric shock, or injury to persons. Following this rule will reduce the
risk of electric shock, re, or serious personal injury.
• Do not abuse cord or charger. Never use the cord to carry the charger. Do not pull the charger
cord rather than the plug when disconnecting from receptacle. Damage to the cord or charger
could occur and create an electric shock hazard. Replace damaged cords immediately.
Not for Reproduction
4
IMPORTANT SAFETY INSTRUCTIONS
• Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged
in any way. Take it to an authorized serviceman for electrical check to determine if the charger
is in good working order.
• Do not cover the ventilation slots on the top of the charger. Do not set the charger on a soft
surface i.e. blanket, pillow. Keep the ventilation slots of the charger clear.
• Do not probe the charger with conductive materials.
• Do not disassemble charger. Take it to an authorized serviceman when service or repair is
required. Incorrect reassembly may result in a risk of electric shock or re.
• Disconnect charger from the power supply when not in use. This will reduce the risk of electric
shock or damage to the charger if metal items should fall into the opening. It also will help
prevent damage to the charger during a power surge.
• Do not mix old and new batteries and do not mix alkaline, standard (carbonzinc) or
rechargeable (ni-cad, ni-mh, etc.) batteries.
• Do not use a damp cloth or detergent on the battery or battery charger.
• Do not allow the battery pack or charger to overheat. If they are warm, allow them to cool
down. Recharge only at room temperature.
• Unplug the charger before cleaning and when there is no battery pack in the cavity.
• Do not try to connect two chargers together.
• Do not allow liquid inside the charger.
• Do not try to use the charger for any other purpose than what is presented in this manual.
• Store indoors, and do not expose to rain or water, avoid direct sunshine.
• Be sure voltage selector is in correct voltage position before plugging in.
• For use in the U.S.A., the voltage selector switch must be placed in the 120 volt position. For
use in countries other than the U.S.A., the voltage selector may need to be placed in other
than the 120 volt position. Conrm the voltage available at each country location before using
the product.
• This power unit is intended to be correctly orientated in a vertical or oor mount position.
• Save these instructions. Refer to them frequently and use them to instruct others who may
use this tool. If you loan someone this tool, loan them these instructions also to prevent
misuse of the product and possible injury.
Not for Reproduction
5
SYMBOLS
Some of the following symbols may be used on this product. Please study them and learn their
meaning. Proper interpretation of these symbols will allow you to operate the product better and safer.
SYMBOL NAME DESIGNATION/EXPLANATION
V Volts Voltage
Hz Hertz Frequency (cycles per second)
W Watts Power
Direct Current Type or a characteristic of current
Wet Conditions Alert Do not expose to rain or use in damp locations.
Read The Operator’s Manual
To reduce the risk of injury, user must read and
understand operator’s manual before using
this product.
Safety Alert Precautions that involve your safety.
The following signal words and meanings are intended to explain the levels of risk associated
with this product.
DANGER
Indicates an imminently hazardous situation, which, if not
avoided, will result in death or serious injury.
WARNING
Indicates a potentially hazardous situation, which, if not avoided,
could result in death or serious injury.
CAUTION
Indicates a potentially hazardous situation, which, if not avoided,
may result in minor or moderate injury.
CAUTION
(Without Safety Alert Symbol) Indicates a situation that may
result in property damage.
SYMBOL SIGNAL MEANING
Not for Reproduction
6
KNOW YOUR CHARGER
The safe use of this product requires an understanding of the information on the product and in
this operator’s manual as well as a knowledge of the project you are attempting. Before using
this product, familiarize yourself with all operating features and safety rules.
Electrical Contacts
LED Light
Cooling Air Port
Electrical Contacts
Cooling Air Port
LED Light
Wall Mounting Holes
Power Cord
Wall Mounting Holes
Power Cord
Not for Reproduction
OPERATION
7
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause
undesired operation.
WARNING
Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
WARNING
Do not allow familiarity with products to make you careless. Remember that a careless fraction of a
second is sufcient to inict serious injury.
WARNING
Do not use any attachments or accessories not recommended by the manufacturer of this product.
The use of attachments or accessories not recommended can result in serious personal injury.
CAUTION
Charge in a well ventilated area. Do not block charger vents. Keep them clear to allow proper
ventilation.
Not for Reproduction
8
OPERATION
CHARGING PROCEDURE
NOTE: The battery is not shipped fully charged. It is recommended to fully charge before rst
use to ensure that maximum run time can be achieved. This lithium-ion battery will not develop a
memory and may be charged at any time.
Low voltage charging:
If the battery has been stored with little to no charge for a long period of time, the charger will go
into recovery mode, which will take 20 hrs to fully charge the battery. This will enhance the life of
the battery. Once it is fully charged, the next charge will return to standard charging.
1. Plug the charger into an AC power outlet.
2. Insert the battery pack into the charger.
This is a diagnostic charger. The Charger LED Lights will illuminate in specic order to
communicate the current battery status. They are as follows:
False defect note:
When the battery is inserted into the charger and the status LED blinks RED, remove the battery
from the charger for 1 minute, then reinsert. If the status LED blinks GREEN, then the battery
is properly charging. If the status LED is still blinking RED, remove the battery and unplug the
charger for 1 minute. After 1 minute, plug in the charger and reinsert the battery. If the status LED
blinks GREEN, then the battery is properly charging. If the status LED is still blinking RED, the
battery is defective and needs to be replaced.
LED STATUS DESCRIPTION
Solid Green Fully Charged
Blinking Green Charging
Solid Red Over Temperature
Blinking Red
Charging Fault
Charging Over
Temperature
Charging
Fault
Fully
Charged
Not for Reproduction
9
CHARGER MOUNTING
1. This charger can be installed hanging on a wall using two #8 screws (not included).
2. Locate the placement for the charger to be wall mounted.
3. If fastening to wood studs use 2 wood screws (not included).
4. For Charger BSRC82: Drill two holes on center 4.5 in. apart ensuring that they are vertically
aligned.
For Charger BSSC82: Drill two holes on center 4 in. apart ensuring that they are vertically
aligned.
5. If fastening to drywall use wall anchors (not included) and screws to secure the charger to the
wall.
6. This power unit is intended to be correctly orientated in a vertical or oor mount position.
NOTE: If the battery and the charger won’t be used for a long time, remove the battery from the
charger and pull out the AC power plug.
OPERATION
Not for Reproduction
10
MAINTENANCE
WARNING
To avoid serious personal injury, always remove the battery pack from the tool when cleaning or
performing any maintenance.
WARNING
When servicing, use only identical Briggs & Stratton replacement parts. Use of any other parts may
create a hazard or cause product damage.
WARNING
It is not recommended to use compressed dry air as cleaning method of the charger. If cleaning
with compressed air is the only method to apply, always wear safety goggles or safety glasses with
side shields when using compressed air to clean the tool. If the operation is dusty, also wear a dust
mask.
GENERAL MAINTENANCE
• Brush or blow dust and debris out of the air vents using compressed air or a vacuum. Keep
the air vents free of obstructions, sawdust, and wood chips. Do not spray, wash, or immerse
the air vents in water.
• Wipe off the housing and the plastic components using a dry, soft cloth. Do not use strong
solvents or detergents on the plastic housing or plastic components. Certain household
cleaners may cause damage and may cause a shock hazard.
STORAGE
• Always remove the battery pack before storing the charger or any time the charger is
unplugged.
• Do not place the battery pack in the sun or in a warm environment. Keep at normal room
temperature.
• If the battery will not be used for 3 months or more, please store the battery in a room
temperature environment. Please fully charge before storage.
WARNING
Do not at any time let brake uids, gasoline, petroleum-based products, penetrating oils, etc. to
come in contact with plastic parts. Chemicals can damage, weaken or destroy plastic which may
result in serious personal injury.
Not for Reproduction
TROUBLESHOOTING
11
PROBLEM CAUSE SOLUTION
Charger doesn't work. Charger
shows defective mode (LED
ashes Red).
Battery pack or charger is
defective or bad connection
between the battery pack and
charger.
1. Try to remove and reinsert
the battery pack in the charger.
2. Try charging a different
battery pack.
3. Unplug the charger and wait
until the red LED goes out,
then reconnect the plug to the
power supply.
Charger doesn't work. Charger
shows evaluative mode (LED
indicates Red solid ON).
Battery pack is too hot or too
cold.
Allow the battery pack to reach
normal temperature. Charging
will begin when battery
pack returns to 3°C-47°C
(37°F-117°F).
Not for Reproduction
LIMITED WARRANTY
12
Briggs & Stratton warrants that, during the warranty period specified below, it will repair
or replace, free of charge, any part that is defective in material or workmanship or both.
Transportation charges on product submitted for repair or replacement under this warranty
must be borne by purchaser. This warranty is effective for and is subject to the time periods and
conditions stated below. For warranty service, nd the nearest Authorized Service Dealer in our
dealer locator map at www.briggsandstratton.com. The purchaser must contact the Authorized
Service Dealer, and then make the product available to the Authorized Service Dealer for
inspection and testing.
There is no other express warranty. Implied warranties, including those of merchantability
and tness for a particular purpose, are limited to the warranty period listed below, or to
the extent permitted by law. Liability for incidental or consequential damages are excluded
to the extent exclusion is permitted by law. Some states or countries do not allow limitations on
how long an implied warranty lasts, and some states or countries do not allow the exclusion or
limitation of incidental or consequential damages, so the above limitation and exclusion may not
apply to you. This warranty gives you specic legal rights and you may also have other rights
which vary from state to state or country to country.**
WARRANTY PERIOD
Consumer Use Commercial Use
Equipment 60 months 90 days
Battery and Battery Charger 24 months None
** In Australia - Our goods come with guarantees that cannot be excluded under the Australian
Consumer Law. You are entitled to a replacement or refund for a major failure and for
compensation for any other reasonably foreseeable loss or damage. You are also entitled to
have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure
does not amount to a major failure. For warranty service, nd the nearest Authorized Service
Dealer in our dealer locator map at BRIGGSandSTRATTON.COM, or by calling 1300 274 447,
or by emailing or writing to [email protected], Briggs & Stratton Australia
Pty Ltd, 1 Moorebank Avenue, NSW, Australia, 2170.
The warranty period begins on the date of purchase by the rst retail or commercial consumer.
“Consumer use” means personal residential household use by a retail consumer. “Commercial
use” means all other uses, including use for commercial, income producing or rental purposes.
Once a product has experienced commercial use, it shall thereafter be considered as a
commercial use product for purposes of this warranty.
To ensure prompt and complete warranty coverage, register your product at the website shown
above or at www.onlineproductregistration.com.
Save your proof of purchase receipt. If you do not provide proof of the initial purchase date at
the time warranty service is requested, the manufacturing date of the product will be used to
determine the warranty period. Product registration is not required to obtain warranty service on
Briggs & Stratton products.
Not for Reproduction
LIMITED WARRANTY
13
ABOUT YOUR WARRANTY
Warranty service is available only through Briggs & Stratton Authorized Service Dealers. This
warranty covers only defects in materials or workmanship. It does not cover damage caused
by improper use or abuse, improper maintenance or repair, normal wear and tear, or stale or
unapproved fuel.
Improper Use and Abuse - The proper, intended use of this product is described in the
Operator’s Manual. Using the product in a way not described in the Operator’s Manual or
using the product after it has been damaged will not be covered under this warranty. Warranty
coverage will also not be provided if the serial number on the product has been removed or the
product has been altered or modied in any way, or if the product has evidence of abuse such as
impact damage or water/chemical corrosion damage.
Improper Maintenance or Repair - This product must be maintained according to the
procedures and schedules provided in the Operator’s Manual, and serviced or repaired using
genuine Briggs & Stratton parts or equivalent. Damage caused by lack of maintenance or use of
non-original parts is not covered by warranty.
Normal Wear and Tear - Like most mechanical devices, your unit is subject to wear even when
properly maintained. This warranty does not cover repairs when normal use has exhausted
the life of a part or the equipment. Maintenance and wear items such as lters, belts, cutting
blades, and brake pads (except engine brake pads) are not covered by warranty due to wear
characteristics alone, unless the cause is due to defects in material or workmanship.
Other Exclusions - This warranty excludes damage due to accident, abuse, modifications,
alterations, improper servicing, freezing or chemical deterioration. Attachments or accessories
that were not originally packaged with the product are also excluded. There is no warranty
coverage on equipment used for primary power in place of utility power or on equipment used
in life support applications. This warranty does not include used, reconditioned, second-hand,
or demonstration equipment or engines. This warranty also excludes failures due to acts of God
and other force majeure events beyond the manufacturer’s control.
Not for Reproduction
TOLL-FREE HELPLINE: 1-800-743-4115
388011985B Rev: 02 (09-25-17)
Briggs & Stratton Corporation
P.O. Box 702
Milwaukee, WI 53201
Not for Reproduction
Avant d’utiliser le produit, veuillez lire et suivre toutes les consignes de
sécurité et les instructions d’utilisation.
Guide D’utilisation
LIGNE D’ASSISTANCE SANS FRAIS : 1-800-743-4115
www.briggsandstratton.com
Chargeur de batterie lithium-ion 82V
1760263 (BSRC82)
Chargeur de batterie lithium-ion 82V
1761122 (BSSC82)
CHARGEUR DE BATTERIE LITHIUM-ION 82V
Not for Reproduction
2
MATIÈRES
Fiche Technique................................................................................................................... 2
Consignes De Sécurité Importantes ................................................................................... 3
Symboles ............................................................................................................................. 5
Veiller À Bien Connaître Votre Chargeur ............................................................................. 6
Utilisation ............................................................................................................................. 7
Entretien ............................................................................................................................ 10
Dépannage................................................ ...........................................................................11
Garantie Limitée.................................................................................................................... 12
FICHE TECHNIQUE
COMPOSANT CARACTÉRISTIQUES
Chargeur Chargeur De Batterie Lithium-ion 82V
Modèle BSRC82
Entrée 120V AC, 50/60Hz, 5A
Sortie 82V DC, 4A
Piods 3.3 lbs (1.5 kg)
Avis de non-responsabilité : *La tension initiale et maximale de la batterie (mesurée à
vide) est de 82 volts. La tension nominale est de 72 V.
Chargeur Chargeur De Batterie Lithium-ion 82V
Modèle BSSC82
Entrée 120V AC, 50/60Hz, 2A
Sortie 82V DC, 2A
Piods 2.0 lbs (0.9 kg)
Not for Reproduction
3
CONSIGNES DE SÉCURITÉ IMPORTANTES
CONSIGNES DE SÉCURITÉ IMPORTANTES –
CONSERVEZ CES INSTRUCTIONS
DANGER – POUR RÉDUIRE LES RISQUES
D’INCENDIE OU DE DÉCHARGE ÉLECTRIQUE,
SUIVEZ SCRUPULEUSEMENT CES INSTRUCTIONS
Lire et veiller à bien comprendre toutes les instructions. Le non-respect de toutes les
instructions ci-dessous peut entraîner un choc électrique, un incendie et/ou des blessures
graves.
AVERTISSEMENT
POUR UNE UTILISATION À L’INTÉRIEUR EXCLUSIVEMENT.
ATTENTION
Risque de choc électrique.
Utilisez l’unité uniquement dans un endroit sec.
ATTENTION
RISQUE D’INCENDIE ET D’ÉLECTROCUTION, NE CROISEZ PAS LES BORNES DE
SORTIE.
ATTENTION
CHARGEZ UNIQUEMENT LA BATTERIE RECHARGEABLE BSB2AH82, BSB4AH82,
BSB5AH82, LES AUTRES TYPES DE BATTERIES POURRAIENT EXPLOSER, MAIS AUSSI
CAUSER BLESSURES ET DOMMAGES.
DANGER
RISQUE DE CHOC ÉLECTRIQUE. NE PAS TOUCHER LES PARTIES NON ISOLÉES DU
CONNECTEUR DE SORTIE OU LES BORNES DE PILES NON ISOLÉES.
• CONSERVEZ CES INSTRUCTIONS - Ce manuel contient d’importantes instructions
relatives à la sécurité et au fonctionnement des chargeur de piles BSRC82/BSSC82.
• Avant d’utiliser le chargeur de piles, lire toutes les instructions et les mises en garde gurant
sur le chargeur de pile, sur la pile et sur le produit utilisant la pile.
• An de réduire les risques d’incendie et d’électrocution, installez l’outil dans une pièce dont la
température et l’humidité sont contrôlées, et ne présentant aucun contaminant conducteur ou
libre.
• L’usage d’un accessoire non recommandé ou vendu par le fabricant du chargeur peut causer
un risque d’incendie, de choc électrique ou de blessures. Le respect de cette consigne
réduira les risques d’incendie, de choc électrique et de blessures graves.
Not for Reproduction
4
CONSIGNES DE SÉCURITÉ IMPORTANTES
• Ne pas maltraiter le cordon d’alimentation ou le chargeur. Ne jamais utiliser le cordon
d’alimentation pour transporter le chargeur. Ne pas débrancher le chargeur en tirant sur le
cordon. Tirer sur la che pour la débrancher. Un cordon ou un chargeur endommagé peut
présenter un risque de choc électrique. Remplacer immédiatement tout cordon endommagé.
• Ne pas utiliser le chargeur s’il a été soumis à un choc violent ou autrement endommagé. Le
coner à un réparateur agréé an qu’il détermine s’il est en bon état de fonctionnement.
• Ne couvrez pas les fentes de ventilations situées sur le dessus du chargeur. Ne posez pas le
chargeur sur une surface souple, telle qu’une couverture ou un oreiller. Gardez les fentes de
ventilation du chargeur dégagées.
• N’introduisez pas de matériaux conducteurs dans le chargeur.
• Ne pas démonter le chargeur. Si un entretien ou une réparation est nécessaire, le coner à un
réparateur agréé. Un remontage incorrect peut entraîner des risques de choc électrique ou
d’incendie.
• Lorsqu’il n’est pas en usage, débrancher le chargeur de l’alimentation secteur. Ceci réduira
le risque de choc électrique ou de dommages au chargeur si des articles en métal venaient à
tomber dans l’ouverture. Ceci aidera également à éviter des dommages au chargeur en cas
de saute de tension.
• Ne mélangez pas des piles neuves et usagées, ne mélangez pas des piles alcalines,
standards (carbone-zinc) et rechargeables (ni-cad, ni-mh, etc.).
• Ne pas utiliser de tissu humide ni de détergent sur la pile ni sur le chargeur de la pile.
• Ne laissez pas la batterie ou le chargeu r surchauffer. S’ils sont chauds, laissez-les refroidir.
Ne procédez à la charge qu’à température ambiante.
• Débranchez le chargeur avant de le nettoyer et lorsqu’aucune batterie n’y est connectée.
• Ne tentez de relier deux chargeurs ensemble.
• Ne laissez aucun liquide pénétrer dans le chargeur.
• Ne tentez pas d’utiliser le chargeur dans tout autre but que celui décrit dans ce manuel.
• Entreposer à l’intérieur et protéger de la pluie ou de l’eau, éviter une exposition directe à la
lumière du soleil.
• Conserver ces instructions. Les consulter fréquemment et les utiliser pour instruire les autres
utilisateurs éventuels. Si cet outil est prêté, il doit être accompagné de ces instructions, an
d’éviter un usage incorrect et d’éventuelles blessures.
• Pour une utilisation aux États-Unis, le sélecteur de tension doit être positionné sur le tension
de 120 volts. Pour une utilisation à l’extérieur des États-Unis, le sélecteur de tension doit être
positionné sur l’autre position. Vériez la tension à utiliser dans votre pays avant d’utiliser le
produit.
• Cette unité doit être correctement orientée lorsque utilisée sur une surface verticale, elle peut
également être utilisée sur le sol.
• Conserver ces instructions. Les consulter fréquemment et les utiliser pour instruire les autres
utilisateurs éventuels. Si cet outil est prêté, il doit être accompagné de ces instructions, an
d’éviter un usage incorrect et d’éventuelles blessures.
Not for Reproduction
5
SYMBOLES
Certains des symboles ci-après sont susceptibles de gurer sur cet appareil. Etudiez-les et apprenez
leur signi cation. Une interprétation correcte de ces symboles vous permettra d’utiliser votre appareil
dans de meilleures conditions de sécurité et de manière plus adéquate.
SYMBOLE NOM DÉSIGNATION/EXPLICATION
V Volts Tension
Hz Hertz Fréquence (cycles par seconde)
W Watts Alimentation
Courant continu Type ou caractéristique du courant
Alerte à l’humidité
Ne pas exposer l’outil à la pluie ou utiliser dans
un environnement mouillé.
Lisez le guide d’utilisation
Pour réduire le risque de blessure, les
utilisateurs doivent lire et comprendre le guide
d’utilisation avant d’employer ce produit.
Alerte de sécurité Précautions touchant à votre sécurité.
Les termes de mise en garde suivants et leur signication ont pour but d’expliquer le degré de
risques associé à l’utilisation de ce produit.
DANGER
Indique une situation extrêmement dangereuse qui, si elle
n’est pas évitée, entraînera des blessures graves ou mortelles.
AVERTISSEMENT
Indique une situation potentiellement dangereuse qui, si elle
n’est pas évitée, pourrait entraîner des blessures graves ou
mortelles.
ATTENTION
Indique une situation potentiellement dangereuse qui, si elle
n’est pas évitée, pourrait entraîner des blessures légères ou
de gravité modérée.
ATTENTION
(Sans le symbole Alerte à la sécurité) Indique une situation qui
pourrait entraîner des dommages matériels.
SYMBOLE SIGNAL SIGNIFICATION
Not for Reproduction
6
VEILLER À BIEN CONNAÎTRE VOTRE CHARGEUR
Pour utiliser ce produit en toute sécurité, vous devez comprendre les renseignements gurant
sur l’outil et dans le présent guide d’utilisation, et vous devez avoir de bonnes connaissances
au sujet du projet que vous allez entreprendre. Avant d’utiliser ce produit, familiarisez-vous avec
toutes ses caractéristiques et avec les règles de sécurité qui s’y rapportent.
Contacts électriques
Lampe à DEL
Arrivée D’air De
Refroidissement
Contacts électriques
Arrivée D’air De
Refroidissement
Lampe à DEL
Trous Pour
Montage Mural
Cordon D’alimentation
Trous Pour
Montage Mural
Cordon D’alimentation
Not for Reproduction
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
