Eureka 4870ATV Le manuel du propriétaire

Marque: Eureka

Modèle: 4870ATV

Catégorie: Aspirateurs

Taper: Le manuel du propriétaire

Ce manuel convient également à

4870AT

Do not return this

product to the store,

For assembly problems or

questions contact: Eureka's

Customer Service Division toll

free at 1-800-282-2886*, 8a.m.

to 7:30 p.m., (CST), Monday-

Friday and 10 a.m.- 6:30 p.m.

(CST) Saturday.

For replacement of broken

or missing items to be

shipped direct to you, call

1-800-438-7352", 8 a.m. to

4:45 p.m., Central Standard

Time, Monday through Friday.

*En Mexico flame al 5670-6169

um C ;r

Household Type

Series

Index

important Safeguards ............ 2

Service Information ............... 4

Assembly ............................ 5-6

Use ..................................... 7-8

Thermal Cut Off ............... 4 & 8

Accessories ........................... 9

Clear Tubes .................... 10-11

Brush Roll ............................ 12

Brush Roll Belt ................ 12-13

Dust Bag ........................ 13-14

Filters ............................. 14-15

HEPA Filter .......................... 15

Light Bulb ............................ 15

Problem Solving .................. 16

Customer Order Form ......... 17

Warranty .............................. 19

Fitl in and Retain:

We suggest you record the model, type and serial numbers below, they are located on the silver rating plate on your cleaner,

and attach the receipt to the owner' guide as proof of purchase. For prompt and complete service information, ak_ays refer to

these numbers when inquiring about service.

Modem&Type

Seria! No. www.euteka.com

T SAFEG

VVhen using an electrical appliance, basic precautions should always be followed, including the following:

READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER.

To reduce the risk of fire, electric shock, or injury:

" Do not use outdoors or on wet surfaces.

" Do not leave vacuum cleaner when plugged in. Turn off the switch and unplug the electrical cord when not in use and

before servicing.

" Do not allow to be used as a toy Close attention is necessary when used by or near children.

" Use only as described in this manual. Use only manufacturer's recommended attachments.

" Do not use with damaged cord or plug. if vacuum cleaner is not working as it should, has been dropped, damaged, left

outdoors, or dropped into water, return it to a service center before using.

" Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners. Do

not run vacuum cleaner over cord. Keep cord away from heated surfaces.

" Do not use extension cords or outlets with inadequate current carrying capacity

" Turn off all controls before unplugging.

" Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

" Do not handle plug or vacuum cleaner with wet hands.

" Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair, and anything that

may reduce airflow.

" This vacuum cleaner creates suction and contains a revolving brush roll. Keep hair, loose clothing, fingers, and all parts

of body away from openings and moving parts.

" Do not place cleaner on furniture or stairs as the brush roll may cause damage. Place cleaner on floor with the handle in

storage position while using attachments.

" Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.

" Do not use without dust bag in place.

" Belt pulleys can become hot during normal use. To prevent burns, avoid touching the belt pulley when servicing the drive

belt.

" Use extra care when cleaning on stairs.

" Do not use to pick up flammable or combustible liquids such as gasoline, or use in areas where they may be present.

" Store your cleaner indoors in a cool, dry area.

" Keep your work area well lighted.

" Unplug electrical appliances before vacuuming them.

TEE

C ILS

7 7

Lors de l'utilisation d'un appareil electrique, quelques precautions el6mentaires doivent 6tre obsewees, incluant les suivantes:

USEZ TOUTES LES iNSTRUCTIONS AVANT D'UTILJSER VOTRE ASPJRATEUR.

TI E T

Pour reduire le risque de feu, de choc electrique, ou de bJessure:

Ne pas utiliser a I'ext@ieur ou sur des surfaces mouiJlees.

Fermez le commutateur et d_branchez I'appareil Iorsque vous ne I'utilisez pas ou avant le nettoyage ou I'entretien.

Ne permettez pas qu'il soit utilise comme jouet. Une attention particuli@e est necessaire lorsque utilise par ou pres d'un

enfant.

Suivez les recommandations d'utilisation de ce manuel. Utilisez uniquement les accessoires recommandes par le fabriquant.

Ne pas utiliser si le cordon ou la fiche sont endommages. Si I'aspirateur ne fonctionne pas comme il le devrait, s'il a et6

echapp6, s'il est endommage, s'il a et6 laisse a l'ext@ieur ou echapp6 dans l'eau, retournezde a un centre de service

avant d'utiliser.

Ne pas le tirer ou le transporter par le cordon, ne pas utiliser le cordon en guise de poignee. Ne pas fermer une porte sur

le cordon ou tirer le cordon sur des coins ou bordures pointus. Ne pas circuler sur le cordon avec l'aspirateur. Tenir le

cordon a distance des surfaces chauffantes.

Ne pas utiliser des ralJonges ou des prises qui n'ont pas de capacite suffisante pour transporter le courant.

Fermer tousles contr61es avant de debrancher.

Ne pas debrancher en tirant sur le cordon. Pour debrancher, tenez la fiche et non le cordon.

Ne pas manipuler la fiche ou I'aspirateur avec les mains mouilJees.

Ne pas den ins@er dans les ouvertures. Ne pas utiliser si des ouvertures sont bloquees; assurez-vous qu'elJes soient

degag6es de poussi@e, mousse, cheveux ou toute autre chose qui pourrait reduire le passage de Fair.

Cet aspirateur cre6 de la succion et contient un rouleau-brosse tournant. Tenir les parties mobiles et les ouvertures loin

des cheveux, du linge, des doigts et de toute pattie du corps.

Ne pas mettre l'aspirateur sur les meubles ou sur les escaliers car le rouleau-brosse peut faire des dommages. Placer

l'aspirateur sur le plancher avec le manche en entreposage position temps que les accessoires sont en usage.

Ne pas ramasser des objets qui brQlent ou fument comme les cigarettes, alJumettes ou cendres chaudes.

N'utilisez pas sans le sac de poussi@e en place.

Les poulies du courroie peuvent devenir chaudes pendant I'utilisation normale. Pour pr@venir des brQlures, @vitez de

touche la poulie du courroie lorsque vous r@parez la courroie.

Portez une attention particuli@re lorsque vous nettoyez les escaliers.

Ne pas utiliser pour ramasser des liquides inflammables ou combustibles comme de l'essence: Ne pas utiliser dans les

endroits o(4ces liquides pourraient @trepr@sents.

Entreposez votre aspirateur a l'int@ieur dans un endroit propre et sec.

Maintenez un bon @clairage ¢5l'endroit 0(4vous travailJez.

Debrancher les appareils electrique avant de les balayer.

CESl

To reduce the risk of electric shock, this appliance has a polarized plug (one blade wider than the other). This plug will fit

in a polarized outlet only one way. Jfthe plug does not fit fully in the outlet, reverse the plug. if it still does not fit, contact a

qualified electrician to instalJ the proper outlet. Do not change the plug in any way

Afin de r_duire le risque de choc _lectrique, cet appareil est muni d'une fiche polarisee (une des lames est plus large).

Cette fiche ne peut 6tre ins@ee dans une prise polarisee que d'une seule fagon. Si la fiche ne peut 6tre ins@ee dans la prise,

retourner la fiche. Si la fiche ne peut toujours pas 6tre ins@ee dans la prise, faire instalJer une prise adequate par un

electricien qualifie. Ne pas modifier la fiche.

GENERAL INFORMATION

The cleaner is designed to pick up dirt and dust particles. Avoid picking up hard or sharp objects with the cleaner to prevent

bag tears and hose clogs with subsequent motor damage.

Service Information

The instructions in this booklet serve as a guide to routine maintenance. For additional service information teJephone our toll

free number for the nearest Eureka Authorized W,'arranty Station. You should know the model, type and serial numbers

when you call:

USA: 1-800-282-2886

Mexico: 5670-6169

Canada: 1-800-282-2886

if you prefer, you can write to The Eureka Company, Service Division, 807 N. Main Street, BJoomington, illinois 61701, USA.

in Canada write to The Eureka Company, 866 Langs Drive, Cambridge, Ontario N3H 2N7. Refer to The Eureka Limited

Warranty for complete service information.

DO NOT OiL the motor or the brush toll at any time.The bearings are permanently lubricated and sealed.

"Thermal Cut Off

This vacuum cleaner has a special thermostat that protects the cleaner in case of motor overheating. If the cleaner suddenly

shuts off, push the rocker switch to off (O) and unplug the cJeaner. Check the cleaner for a possibJe source of overheating

such as a full bag, a blocked hose or clogged filter. Jfthese conditions are found, fix them and wait at least 30 minutes before

attempting to use the cleaner. After the 30 minute period, plug the cleaner back in and turn on the switch, if the cleaner still

does not run, then tare it to a Eureka Authorized Service Center for repair.

HOW TO ASSEMBLE

CAUTION: Assemble the cleanerbeforeusing,

CAUTION: Moving parts. Make sure onloff switch is in off (0) position before plugging in.

NOTE: Features may vary by modem yet aJt parts assemb{e the same.

Step A Attach HandJe

CAUTION: Do not catch cord under handle.

Handle

3 Locations

for Screws

From rear of cJeaner, aJign handJe with grooves and

sJide onto cleaner, if necessary, use thumb and finger

pressure to slide handle into position.

Attach handle with three I inch screws in the assembly

packet. Use either a fiat or PhijJips® head screwdriver.

Step B Store Hose and Accessories

Hose

Retainer

Upholstery

NozzJe

Crevice

Tool

Dusting

Brush

Nozzle

Retainer

To store hose. Remove paper holding hose to unit.

Lay hose over hose retainer and place nozzle on

nozzle retainer.

Store tools, crevice tool, dusting brush and upholstery

nozzle where indicated above.

Step C Check Disposable Dust Bag

5. Remove front cover. Lift bag cover latch up and

pull bag cover away from unit.

m Bag Cover Latch

Check to be sure the paper bag collar is secure

with the bag adapter inside the paper bag collar.

NOTE: Bag cover will not shut if paper bag is

not properly installed.

Bag Adapter

Paper Bag Collar

Replace front bag cover.

NOTE: See pages 13 & 14 for complete bag

installation instructions.

Step D

Store EmectricamCord

Cord

Retainer {_

Cord

Hook

Cord

-- Hook

You will find your cord retainer on the handle above

the upper cord hook. Firmly push the electrical cord

down into the cord retainer before using the vacuum.

This will place the cord out of the way while you are

vacuuming. Remove cord from retainer when ready

to store vacuum or when using hose and

attachments.

Next wind the cord around the two cord hooks on

the back of cleaner. The upper cord hook turns to

release the cord. Turn the hook up to store the cord.

10. Secure the plug to the cord to prevent unwinding.

HOW TO USE

1. Cord Retainer. To use, push electrical cord down into cord retainer.

2. ON/OFF Switch. International symbol Imeans On, International symbol

O means Off.

3. Hose/Floor Selector. Turn to select hose for above floor cleaning or

floor for floor surface cleaning, if cleaning hard floor surface also adjust

the cleaner height setting to hard floor.

4. Cam Latch. To release clear tubes.

Dirt Alert Indicator (on some models). The dirt alert sensor uses infra-

red technology to indicate whether or not floors are clean. When debris

breaks the light beam, the red light comes on indicating additional

cleaning is needed in this area. if there is no break in the light beam,

the floor is clean and no light will come on.

When using your new vacuum you may be cleaning deep down dirt

missed by your old vacuum causing the light to stay red longer. With

frequent cleaning, after the first few times you use your Eureka vacuum,

the red light should go on less.

To check if the dirt alert sensor is working properly:

A. While the red light ison, tip the vacuum backwards on rear wheels,

lifting the brush roll off the carpet a couple of inches.

B. After a few seconds the red light should turn off.

6. Bag Change Indicator (on some models). Some models feature a

bag change indicator to remind you to change the bag. When it is time

to change the bag, the bag change indicator will illuminate.

Certain types of fine particles like powder, piaster dust, or fine road

dust can restrict airflow very quickly. The fine particles will decrease

performance even before the bag appears to be full Change the dust

bag to restore maximum performance.

7. Bag Cover Latch. Pull up on latch to remove bag cover giving access

to the dust bag and motor filter. Push on latch to close cover.

8. HEPA Filter Door Latch. Squeeze latch and pull out to remove HEPA

Filter Door giving access to the HEPA Filter. Push on latch to close

door.

9. Handle Release. Step on handle release. Pull handle back to a

comfortable position.

10. Stair Handle. To use when cleaning stairs.

11. Brush Roll Control Flip this lever to choose between cleaning hard

floors and carpeting. Brush roll is"off" for hard floors and "on"for carpets.

NOTE: When handle is in upright position, brush roll

automatically shuts off.

12. Cleaner Height Setting. The front of the cleaner has an adjustment that raises or lowers the cleaner base to match the

type of floor surface. With the cleaner cord unplugged, set the adjustment to lowest setting for maximum carpet cleaning.

If the cmeaner is difficult to push, move adjustment to next highest setting until cleaner is comfortable to push.

The brush roll must reach the carpet for effective cleaning. The optimal hard floor cleaning adjustment is located next to

lowest carpet setting. For ease in moving the adjustment knob, place handle in operating position and tilt cleaner back to

remove weight from front wheels.

NOTE: The suction against some types of flooring may require higher cteaner height setting. The Hard F!oor

setting is recommended, but the actual setting used for your hard floor may need to be adjusted for best

performance and ease of movement.

WARMNG: Avoid injury. Keep loose clothing, hair, fingers, and a{I other parts of body away from any moving

part (such as the revolving brush). Turn off the switch and unp{ug the cleaner before changing the

cleaner height setting.

13. Headlight.

HOW TO USE (continued)

_Jj

EZ3

EZ_

14. Hose Retainers (2). Place hose on retainers to store hose on unit.

15. Electrical Cord Hooks (2}. Wrap electrical cord around them to store

electrical cord on unit.

16. ClearTubes (2}. The larger clear tube carries the dirt from the brush

roll area into the dust bag. The smaller clear tube carries the dirt from

the hose for above the floor cleaning to the dust bag.

17. Upholstery Nozzle Storage. Store upholstery nozzle here.

18. Car_{ng Handle. Use this handle to carry unit from one place to

another.

19. Crevice Tool Storage. Store crevice tool here.

20. Dusting Brush Storage. Store dusting brush here.

21. QuarterTum Fastener. Located behind the electrical cord, this fastener

locks the clear tubes in place.

NOTE: WHEN UNiT _S RUNNING, DO NOT

ATTEMPT TO REMOVE ANY OBJECT

WHICH PREVENTS THE BRUSH ROLL

FROM TURNING.

First, mock handme in storage position, turn off

unit, unplug from the e_ectrica_ socket, then

remove object from brush roll area. Ex: sock,

rug, etc.

Therma_ Cut Off

This cleaner has a special thermostat that protects the cleaner in case

of motor overheating. If the cleaner suddenly turns off, follow this

procedure:

1. Push rocker switch to off (O) position.

2. Unplug cleaner.

3. Check for source of overheating problem (i.e. full bag, clogged hose,

clogged tubes or clogged filter).

4. If a full bag, clogged hose, clogged tube or clogged filter is found, replace

the bag, unclog the hose or replace the filters.

5. VVaitat least 30 minutes before attempting to reuse the cleaner.

6. After 30 minute cool down period, plug the cleaner in and push the

rocker switch to the on (I) position. The cleaner should turn on.

7. If the cleaner still does not operate, take it to any Eureka Authorized

Service Center for repair.

How To Use Accessories

NOTE: Place cleaner on floor with the handle

in storage position while using

accessories, Do not place cmeaner on

furniture or steps.

1. Remove hose from rear of cleaner.

2. Place desired accessory onto end of hose or wand.

3. Move hose!floor valve to hose position.

End of

Hose

Dusting Brush is for furniture, blinds, books, lamp shades,

shelves.

Dusting Brush

Upholstery nozzle is for curtains, draperies, cushions,

fabrics.

Upholstery

Nozzle

Crevice too_ cleans corners, baseboards, between cushions.

Crevice Tool

Extension wands

Nested extension wands to add reach.

Turn ridge end to center.

Grasp both wands near ridges.

I 1

Pull apart.

Push wands together.

]

How to Remove and Check CmearTubes

Low suction or poor pickup may be due to a blockage in the vacuum cleaner.

To Check Attachment Hose

1. Move hose/floor valve (A) to hose position.

2. Remove hose (B) and check suction at end of hose =if little or no suction, check

disposable dust bag and filters. Change if needed, if no improvement proceed to

step 3.

NOTE: Turn off the switch and unp{ug the electNca{ cord before checking tubes.

To Check Large base hose coming from hood, go directly to step 3.

3. Turn quarter turn fastener (C) to unlock.

4. Lift latch (D).

5. Pull small clear tube (E) down and away from cleaner.

6. At hose/clear tube connection, rotate twist lock (F) to release tube.

7. Check for blockages.

8. Remove large clear tube (G) by swinging back and pulling down and away from

cleaner.

9. At large hose/clear tube connection, rotate twist lock (H) to release tube.

10. Check for blockages in both clear tubes (EtG) and both hoses (I).

NOTE: Clean tubes with mild detergent. Do not put them in a dishwasher. Make

sure atl parts are completely dry prior to reassembling.

How to Reassemble Clear Tubes

11. Reattach both clear tubes (J) (push and twist) to hoses (I) on cleaner.

12. insert large clear tube into large hole (K). Be sure to insert completely. Make sure the

latch (D) is open so the clear tube can be fully installed.

13. Slide ribs at the bottom of the large clear tube (L) into the slot on the cleaner until the

clear tube is vertical.

14. insert small clear tube (M) into small hole. Be sure to insert completely.

15. Push into place so both clear tubes are vertical (N). The bottoms of the clear tubes will

interlock.

16. Adjust small clear tube until quarter turn lock (O) is correctly located on back of cleaner.

17. Use a coin to turn the quarter turn lock clockwise to lock (P).

18. Close latch (R), securing the clear tubes at the top.

HOW TO MAINTAIN

The instructionsin this booklet serve as a guide to routine maintenance. To avoid unnecessary service calls, check the bag,

belt, and brush roll often.

Brush Roll

The brush roll turns as it sweeps and combs the carpet nap. Remove hair and threads from the brush roll so it continues

brushing the carpet. To maintain the most efficient cleaning, the bristles must touch the carpet. To test the bristle length,

hold a ruler against the underneath side of the cleaner. If the bristles no longer touch the ruler, replace the brush roll.

Brush Roll Belt

The brush roll belt turns the brush roll to agitate, sweep, and comb the carpet nap. Check the belt regularly to be sure it is

in good condition. Replace the belt if itcracks or tears. Cut away any hair or threads wound around the brush roll or the belt

pulley because the buildup could cause the belt to rotate unevenly

How To Replace Brush Roll Belt, PartNo.61110

NOTE: Turn offthe switch and unplug the electNcal cord

before replacing belt. Belt pulleys can become

hot during normal use. To prevent injury, avoid

touching the motor shaft when checking the belt.

........... z.

1. Move brush roll control lever to hard floor position.

2. Remove 3 base plate screws using a Phillips@

screwdriver. Lift base plate off base.

Motor

Shaft

Brush

Roll

Pulley

3. Remove brush roll. Place new belt around motor shaft

and brush roll.

NOTE: The new belt witl appear to be too large. This is

normal.

4. Insert left end into base.

HOW TO MAINTAIN (continued)

The instructions in this booklet serve as a guide to routine maintenance. To avoid unnecessary service calls, check the bag,

belt, and brush roll often.

HowTo Replace Brush Roll Belt (continued)

5. insert right end into base. Make sure it is fully into

position. Ensure belt is centered. NOTE: The new belt

will appear to be too large. This is normal

Slots

Replace base plate by first inserting all 4 front tabs

into slots on base. Rotate down on cleaner and replace

3 screws.

Disposable Dust Bag and FHters

The disposable dust bag plays a very important role in

the efficiency of a vacuum cleaner. The purpose of the

paper bag is to trap dirt. As the bag traps dirt, it must also

be porous enough to allow air to pass on through. If the

paper bag becomes clogged, no air can pass through the

cleaner and no cleaning can take place regardless of how

powerful the unit. Change the dust bag and check the

filters frequently. Some fine particles can restrict airflow

very quickly and will decrease performance even before

the bag appears to be full.

When vacuuming carpet fresheners or cleaners, powder,

plaster dust, or similar fine substances, the bag and filters

may require more frequent maintenance.

How To RepNace Bags-Style RR

Filteraire

NOTE: Turn off the switch and unplug the electrical

cord before changing dust bag. Never operate

the vacuum cleaner without the dust bag or

the filter.

NOTE: Sty{e RR Filteraire bags must be used to

maintain HEPA grade filtration and prolong the

life of the HEPA filter.

"To Remove Bag:

Latch

Bag Cover

1. Release front cover latch by lifting up. Pivot bag cover

away from cleaner and remove.

NOTE: Bag cover will not shut if paper bag is not

properly installed.

"To Remove Bag" (continued)

Pull and hold lever to left, away from bag (A). Grasp

cardboard bag collar (C) and pivot collar down until it

snaps loose on right side. Remove bag from cleaner

and discard.

To Replace Bag:

3. Locate back ledge (B). Place bag collar on ledge.

Push up with both thumbs until bag secures on each

side. Check to be sure the paper bag collar (C) is

secure with the hose adapter (D) inside the paper

bag collar.

5. Tuck bag into bottom and along sides.

6. Place tab on lower part of front cover into cleaner

slot. Close cover. Make sure disposable bag is not

caught under front cover.

Use replacement bag, 61118, Sty{e RR.

Back Ledge

', II ..... Collar

i I,'

C_eaning and Replacing FiRers

Motor Filter

Check the motor filter with each disposable dust bag change. Clean or replace as needed. Never operate without motor

fiRer in place.

To Clean Motor Filter

1. Lift up on filter retainer handle to remove filter retainer.

Then lift up on filter to remove filter from holding pegs.

2. Shake filter to remove excess dust. If necessary, the

filter can be cleaned by vacuuming with another

cleaner.

3. Reinstall filter, pressing onto holding pegs. Replace

filter retainer.

To Replace Motor Filter

1. Remove motor filter retainer and filter from inside bag

compartment.

2. Install new filter, by placing on holding pegs. Replace

filter retainer.

Use replacement motor filter, 70082.

Holding

FHter Retainer

Handle

Motor

FiRer

Cleaning And Replacing Filters (continued)

HEPA Fi_ter

Check the HEPA filter with each disposable dust bag

change. RepJace at least twice a year or after every six

bag changes.

"To Remove HEPA Fi_ter ° Style HF2

1. Squeeze HEPA door latch and swing open.

2. Remove HERA filter.

To Replace HEPA Filter

1. Place HEPA filter inside HEPA compartment with

rubber seal against the back of the compartment.

2. Replace HEPA door. Push HEPA Door Latch against

the unit until it locks into place.

Use replacement HEPA fitter, 61111, Style HF2.

HEPA

Door

Latch

How "ToChange Light Bumb (only for models with a headlight)

NOTE: Turn off the power switch and disconnect the

electrical cord before changBng light bulb.

1. Lower handle to remove two screws from lens cover.

2. Pull lens cover from cleaner.

3. Pull up on light bulb to remove.

4. Push new light bulb into socket.

5. Replace lens cover.

6. Secure with two screws.

Use replacement bulb, 57940=2.

PROBLEM SOLVtNG ° Call I-8oo-438-7352 for replacement of broken or missing items.

NOTE: Turn off the switch and unplug the ebctrical cord before servicing.

CAUSE

E_ Electric Plug [_

[_ Thermal Cut Off [_

[_ Disposable Dust Bag [_

and Filter(s)

[7 Belt [_

[_ Brush Roll [_

[_ Hose [_

[_ Brush Roll Control [_

E_ Cleaner Height Setting [_

[_ Disposable Dust Bag [_

and Filters

[_ Hose [_

[_ Hose/Floor Selector [_

E_ Light Bulb Eli

[_ Brush Roll [_

E_ Belt Eli

[_ Cleaner Height Setting [_

PROBLEM SOLUTION

Motor will not start. Push plug securely into outlet.

Try another outlet.

Check circuit breaker.

Refer to page 8.Motor suddenly stops.

Does not clean the carpet or

floor.

No suction at the end of the

hose,

Change the bag. Hint: If picking up fine dust, the bag

may not look full, but a fine substance tends to reduce

suction when it blocks the airflow through the paper bag

and filter(s). Make sure the dust bag is installed properly.

Make sure bag cover is installed properly.

Replace a cut, or out of shape belt.

Clean hair and thread from bristles and end cap area.

Replace brush roll if bristles are worn.

Remove any clogs from the hose that restrict the airflow.

For carpet cleaning make sure brush roll control lever is

in carpet position and the hose/floor selector is on floor

selection,

For hard floor cleaning, make sure brush roll control is in

hard floor position and hose/floor selector is on floor

selection,

Change the bag. Hint: If picking up fine dust, the bag

may not look full, but a fine substance tends to reduce

suction when it blocks the airflow through the paper bag.

Check the filters and clean or replace if necessary.

Remove any clogs from the hose that restrict the airflow.

Check both ends of the hose. (See pages 10-11 )

[_ Cleaner Height Setting

E_ No paper bag.

Remove any clogs from the clear tubes that restrict the

airflow. Check hose/floor selector setting.

For above floor cleaning, make sure hose/floor selector

is on hose.

Headlight not working. Replace light bulb.

Noise from the brush roll area. Remove base plate and clean debris from the brush roll

area.

Replace a cut or out of shape belt.

Cleaner is hard to push. Turn adjustment knob to a higher position. Hint: Put

handle in operating position. Tilt the cleaner back to raise

the front wheels off floor. Then turn the knob.

[_ Belt [_ Replace a cut or out of shape belt.

E_ Brush Ro!l On/Off Eli Flip brush roll control lever to carpet position.

Brush rail will not turn. F_,,"Belt [_ Replace cut or out of shape belt.

E_ Brush Roll On/Off Eli Flip brush roll control lever to carpet position.

NOTE: Brush roll is not supposed to turn while the

vacuum is in the upright position.

Dirt Alert red light will not go off. E_ New carpet fibers. Eli Over time loose new carpet fibers will diminish and will not

trip the dirt alert sensors.

Dirt Alert red light will not come on E_ Dirt sensor is not working. Eli Call 1-800-282-2886 8 a.m. to 7:30 p.m,, (CST),

Monday - Friday and 10 a.m. - 6:30 p.m. (CST) Saturday

for the nearest authorized Eureka service center,

Cleaning height knob will not Hint: Put handle in operating position. Tilt the cleaner

turn. back to raise the front wheels off floor. Then turn the knob.

Bag cover will not shut or close. A paper bag must be properly installed for the bag cover

to close.

_at This V/arranO* (7ove_:_'

"_\_m E_tieka cleaner is warranted to be fiee fiom all defects m material and woikmansbip m nom_al household use fbr a peliod of one ?era The wananty is g_amed only to the

o*iginal p*tichase_ and membms of his ol bei immediate bousebokt The wm_anty is subject to the following p*ovisions

V_'7_atThis VYdrmnty Does Not (bver

Parts of the cleanel that reqmre replacement under nom_al use, s_tch as disposable &_st bags, filtels, d*i',e belts, light bulbs, brush 1oll bristles, impellexs and cleaning

Damages or malfimctions caused by ziegligence, abuse, or use ziot m accordm_ce with the Ownel s Grade

Defbcts or damages caused by mmutborized sel_,,ice o*the use of otbex than Genuine Eureka parts

_hat _%e Eureka Company Will Do

The Emeka ( ompany will. at its option lepair oi leplace a defbctive c[eanex o_ cleanex pait that is cove_ed by this wmranty As a mattel ofwarranty policy the Euleka ( ompany

will 11otlefimd the consm_er's pmchase price

Warra,_O, Registration

Please fill out and *etmn the warranty legistxation card accompanying yore cleaner

Obta#_#_g V/arran O,Se_q,ice

_b obtain warramy seIvice you m_st reoun the defective cleaner or deanei part alol_g with proof of pmcba se to any Emeka Autboxized xX,aiianty Station

You will filed the l_earest locatiol_ in d_e Yellow Pages, *mdeI 'Vacmm* Cleanels Sexvice and Repaii" Be cextail_ that the W_r_anty Statio_ is ' Euieka Authorized"

Foi die location of the nemest E_tieka Autboxized _\hi*aiity Station ol foi sexvice intbimation, telepboi_e toll free:

USA: 1-800-282-2886

Mexico: 8670-6169

Canada: 1-800-282-2886

If you prefbr, you can write to The Eureka Company. Service Division, 807 N Mare Street. Bloomington. Illinois 61701. USA In Ca*lade write to The Fmeka Company.

866 Langs Drive, (ambridge Ontario N3H 2N7

If it is necessm T to ship the elem_er outside yore community to obtain wm*anty repam you must pay the shipping charges to the Eureka Atltborized Wananty Station

Reims shipping cbaiges will be paid by the _\_x_anty Station When rermmng parts fbr repair, please bmlude the model, type. and serial mm_ber from the data plate on the cleanex

Further Limitations and E:vchcsions

Any warianty the t may be implied m connection widt your purchase oi use of the clea_ler, including any wa_ianty of Merchamability or m_ywaIla sty %r Fir*tess For A Particula r

Ptlrpose is limited to the duration of this wai_anty Some states do _ot allow limitatio_s o_lhow long an implied warramy lasts, so the above limitations may _ot apply to you

"_\_t_rrelief fbr/he breach of this warranty is limited to the relief expiessly provided above hi no event shall Fureka be liable fbr any consequential or incidental damages you

may inc_t* b_ eon*lection wirb your ptlrchase or use of the cleanex Some states do not allow the exclusion or limitation of incidental ox consequential damages, so the above

limitation oI exclusion may _lot apply to ym_

This warranty g_ves you specific legal rights "_\m may also have other rights which vmy by state

Questions & Answers about Genuine _ureka Products

;> 9 9 9 9

O: Why should I use only Genuine Emeka paper bags belts and parts in m? Emeka vactmm cleanex?

A: Using Genuine Eureka Products, which are made to our exacting specifications and engineered with emphasis on quality, performance, and customer satisfaction,

ensures the long life and cleaning efficiency of your vacuum cleaner. Overall, this saves you money and helps to keep your home clean.

Q: How can I be sine Iam using only geimine Eureka product, m my vacmtm cleaner:

A: Typically, packaged products and paper bags can be identified by a "Genuine Eureka Product" symbol (see illustration above). For further identification assistance,

you may call our toll4ree number, 1-80g-gg2-2886, for the location of a nearby Eureka Authoriaed Warranty Station.

Q: Ale tbeIe any ditf'elences between 'made to fit" oi 'imitation" and Gem_ine Emeka paper bags belts, and parts?

A: Yes, there are some very important differences in materials, quality, and reliability. Nasy customers have mistakenly purchased "imitation" paper bags and parts