Blaupunkt San Jose MP41 Le manuel du propriétaire

Catégorie
Récepteurs multimédia de voiture
Taper
Le manuel du propriétaire
288F0281
SAN JOSE MP41
High-Power FM/AM/CD/MP3 Receiver with Detachable Face
Autoradio FM/AM à Lecteur CD/MP3 de Forte Puissance et à Face Amovible
Receptor FM/AM/Reproductor de CD/MP3 de Alta Potencia y con Panel Extraíble
Rádio FM/AM/CD/MP3 de Alta Potência
com Face Removível
Robert Bosch Corporation
Sales Group —
Blaupunkt Division
2800 South 25th Avenue,
Broadview, Illinois 60155
ENGLISH
FRANÇAIS
ESPAÑOL
PORTUGUÊS
Issue date 08-01
PWR
OPEN
TS
200 WATTS
V
O
L
654321
BND
CD
DISP
SAN JOSE MP41
MUTE
SUB OUT
Important Notice
Prior to Installation, Demo
Mode should be defeated.
See page 7.
San Jose MP41_cover 8/23/01, 2:37 PM1
ENGLISH
E-1
Precautions
This equipment has been tested and found to comply with the
limits for a Class B device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable pro-
tection against harmful interference in a residential installa-
tion. This equipment generates, uses, and can radiate radio
frequency energy, and, if not installed and used in accord-
ance with instructions, may cause harmful interference with
radio communications. However, there is no guarantee that
radio interference will not occur in particular installation. If this
equipment does cause harmful interference to radio or televi-
sion reception, which can be determined by turning the equip-
ment off and on, the user is encouraged to consult the dealer
or an experienced radio/TV technician for help.
You are cautioned that any changes or modifications not ex-
pressly approved in this manual could void your authority to
operate this equipment.
Features
MP3/WMA file playback support
CD-TEXT support (SONG, ALBUM)
Detachable flip down front panel
Built-in power amplifier
(max. output : 50W × 4ch)
FM/AM PLL Synthesizer tuner
30 Station preset memory
Travel Store / Scan tuning
X-BASS System
Station / Disc name store, Station / Disc call
Auxiliary input
IR Remote Control RC-823
CD changer control
(IDCA09, CDCA08 & CDCA071*)
* CDCA071 requires adaptor # 7607 898 093 available
separately.
FCC WARNING
Avoid installing the unit where it would be subject to high
temperatures, such as in direct sunlight or a hot air stream
from the heater, or where it would be subject to dust, dirt, or
excessive vibration.
Do not turn on the unit if the temperature inside the car is
very high. Always cool down the unit before usage. Parking
your car in direct sunlight will result in a temperature rise.
If the unit does not turn on, check the connections first. Then
check whether the fuse at the back of the unit is blown.
Carefully read this manual before using the unit. If you en-
counter any problems that are not covered in this manual,
please consult the dealer where you purchased the unit or
the dealer nearest to you.
This unit has been designed specifically for playback of com-
pact discs bearing the following mark. Other discs cannot
be played.
Handling Compact Discs
Be careful when removing a compact disc after the play-
back is completed because the disc may be extremely hot.
Do not use non-conventional discs such as heart-shaped,
octagonal discs, etc. The player could be damaged.
Do not expose compact discs to direct sunlight or any heat
source.
Check all compact discs before playing, and discard cracked,
scratched or warped discs.
Wipe dirty or damp discs outward from the centre with a
soft cloth.
Do not use any solvents such as commercially available
cleaners, antistatic spray, or thinner to clean the compact
discs.
If a label is affixed to a disc, the label may prevent removal
of the disc from the unit or may damage the unit.
Label
CD
San Jose MP41_body_en 8/28/01, 6:03 PM1
ENGLISH
E-2
Notes
Be sure to use this unit with the front panel closed.
The unit is automatically switched off when the front panel
is left open for about 10 minutes.
Do not handle the unit roughly when opening/closing the
front panel.
Do not put any object or use it like a tray when the front
panel is open in a lying position.
Do not press OPEN button when closing the front panel.
Do not put too much force to the operation buttons or the
display window as it may cause damage or deform the unit.
• Connectors on the unit and front panel are vital parts trans-
mitting the signal. Do not touch, push or scratch them.
• Be careful not to pinch your fingers or hands when opening
and closing the front panel.
• Do not press hard on the front panel when affixing it to the
unit. No more than light to moderate pressure should be
needed.
• Make sure there is no dust or dirt on the electrical terminals
on the back of the front panel as this could cause intermit-
tent operation or other malfunctions.
Detaching the Front Panel
EJECT button
3. Close the inner cover.
Do not leave inner cover in the down position unless the
front panel is in place.
2. Pull the front panel toward your direction to remove it.
1. Press the
OPEN
firmly to open the flip down front panel.
Ejecting the CD
Press the recessed button located to the left behind the Front
Panel.
Handling the Front Panel
Attaching the Front Panel
Place the right hand side of the front panel so that the parts
A of the front panel are engaged with the parts B of the unit
as shown below. Then push the left hand side of the front
panel until it is securely locked.
Front Panel Open / Close
Panel open
Press the
OPEN
.
Panel close
Raise the front panel with your
finger until it locks in place.
Security/Retailer Display
Bolt the front panel with the locking screw (See page 19) in
the inner cover as shown below, to protect the front panel
from theft and from getting lost.
Locking screw
San Jose MP41_body_en 8/28/01, 6:03 PM2
ENGLISH
E-3
Identification of Controls
1 OPEN button
Open the flip down front panel.
2 PWR button
Turns the power of the unit on or off.
3 TUN/TRK button
Used to tune in to the desired station.
4 LCD Display window
5 CD button
Select the operating source (CD, CD changer or AUX).
6 BND/TS button
Selects the AM/FM Band & Travel store.
7 DISP button
Mode selector. Clock adjustment. Display priority setting.
8 MUTE/SENS button
Muting the sound. Switches the seek sensitivity between
local and distance.
9 XBASS button
Boosts the bass sound.
10 PRESET MEMORY button
During radio reception :
1
-
6
; For Preset memory
During CD mode :
4/MIX
; For Mix play (Mix & Mix all during CDC)
5/RPT
; For Repeat play
6/
; For Pause
PWR
OPEN
TS
200 WATTS
V
O
L
654321
BND
CD
DISP
SAN JOSE MP41
MUTE
SUB OUT
11 JUMP button
If an ID3 Tag has been recorded on MP3 file, one touch
switches the unit to ID3 Tag display. (Not supported with WMA.)
12 FOLDER SELECT button
Select the desired CD in CDC (CD changer) mode.
Select the desired FOLDER in MP3/WMA play mode.
13 SC/PS button
Scan tuning. Preset scan tuning. Scan play in CD/CDC mode.
14 AUDIO button
Audio control selector; Bass, Treble, Loudness, Balance
& Fader.
15 Dial
Adjusts the volume level/bass/treble/balance/fader.
Used to store the station names, and selects alpha-nu-
meric characters.
16 Infrared Sensor (behind acrylic facia)
Permits wireless remote control of AM/FM/CD and CD
changer with RC-823 credit card style remote.
Remote Control (Included)
You can operate your receivers basic AM, FM, CD, MP3 &
CDC features via an IR Remote Control, model RC-823.
1
2
3
4
7
5
9
10
15
14
13
12
16
6
8
12
3
4
6
7
5
8
9
1011
1314
15
16
1 L-ch Level Meter
2 R-ch Level Meter
3 XBASS indicator
4 Main display section
5 STEREO signal indicator
6 Signal-strength indicator
7 lo(Local) indicator
8 MUTE indicator
9 LOUD indicator
10 MIX/RPT/SCAN Mode indicator
11 Clock indicator
12 CD Changer indicator
13 ID-3 Tag indicator
14 DISC IN indicator
15 FOLDER indicator
Flashes when the folder name is displayed.
16 FILE indicator
Flashes when the file name is displayed.
Front Panel
LCD Display
12
11
San Jose MP41_body_en 8/28/01, 6:04 PM3
ENGLISH
E-4
General Operations
Turning the power On/Off
Press the
PWR
to turn on or off the unit.
Tip
When you turn on the unit, BLAUPUNKT MP3 - I WANT MY
MP3! will be displayed before actual power on.
When you turn off the unit, BYE - BYE will be displayed
before actual power off.
You can edit these message. (See Turn on/off message
edit)
Volume Level Control and Memory
Rotate the dial to adjust the volume.
It is also possible to set the maximum volume when the power
is switched on by following the procedure explained below.
1. Turn the dial until it is set at the required volume.
2. Press the
PWR
for two or more seconds. The power will
be switched off and the current volume level recorded.
Muting the sound
Press
MUTE / SENS
.
MUTE appears on the display window.
To restore the previous volume level, press
MUTE / SENS
again.
Volume down
Setting the Clock
The clock uses a 12-hour display system. (factory set)
1. Turn the ignition key to the ON position.
2. Press the
PWR
to turn on the unit.
3. Repeatedly press the
DISP
to display CLOCK 12.
4. Rotate the dial within 5 seconds to select the 12 or 24-
hour time mode. Each time you rotate the dial, the mode
changes or toggles as follows :
5. Repeatedly press the
DISP
to display CLOCK ADJUST.
A. Press the
MUTE / SENS
within 5 seconds to flash the hour digit.
B. Rotate the dial to set the hour digit.
C. Press the
MUTE / SENS
to flash the minute digit.
D. Rotate the dial to set the minute digit.
6. Press the
DISP
momentarily to complete the Clock set-
ting mode.
Note
If you make no button input or dial operation in 20 seconds,
the Clock setting mode will turn off automatically.
Ignition-off Clock Recall
The display will illuminate showing the time and then auto-
matically shut off after 5 seconds.
Press the
DISP
while the ignition switch is in the OFF posi-
tion.
CLOCK 24
CLOCK 12
Volume up
Adjusting the Sound Characteristics
1. Press the
AUDIO
to select the desired adjustment mode
as follows;
BASS 0
TREBLE 0
LOUD OFF
(LOUDNESS)
BAL L0 R0
(BALANCE)
FAD R0 F0
(FADER)
2. Rotate the dial to adjust the selected item.
Adjust within 3 seconds after selecting the item. After 3
seconds, the dial reverts to volume control. Use the fol-
lowing tables as a guide for adjusting the settings in each
mode.
Adjustment Range
BASS BASS 5 BASS +5
TREBLE TREBLE 5 TREBLE +5
LOUDNESS LOUD OFF LOUD ON
BALANCE L9 R0 (Full left) L0 R9 (Full right)
FADER R9 F0 (Full rear) R0 F9 (Full front)
Tip
Settings for BASS, TREBLE, LOUDNESS and XBASS can
be made to each of the following modes independently:
FM, AM, CD, MP3, CD Changer and AUX.
San Jose MP41_body_en 8/28/01, 6:04 PM4
ENGLISH
E-5
Mode Selector
Each time the
DISP
is pressed, the display window will change
over as shown below;
Priority indication
STATION(DISC) CALL * : Refer to " Display priority setting "
DSP PRIORITY : Refer to " Display priority setting "
DISP. SPEED : SLOW / FAST
SCROLL TYPE : ROLLING / WITH PAUSES
METER 1 : METER 0 / METER 1 / METER 2 / METER 3 / METER 4
LEVEL 1 : LEVEL 1 / LEVEL 2
CONTRAST : 10 ~ 0 ~ +10
MESSAGE ON : MESSAGE ON / MESSAGE OFF
CLOCK ADJUST : Refer to " Setting the Clock "
CLOCK 12 : Refer to " Setting the Clock "
* : Radio mode only
DEMO ON : Refer to " How to defeat Demo Mode "
Notes
•“STATION CALL and DSP priority are not displayed in
AUX mode.
If you make no button input or dial operation in few sec-
onds, the display returns priority indication.
Display priority setting
Example
To set Station Name to the Display Priority.
1. Repeatedly press the
DISP
to display DSP PRIORITY
appears in the display window.
2. Rotate the dial to select STATION NAME or FRE-
QUENCY.
3. Hold the
DISP
pressed for more than 2 seconds to con-
firm/enter your selection.
NO NAME or a previously assigned station name (See
page 10) flashs once to indicate that Station Name is
selected for the Display Priority.
After 5 seconds, the display mode will automatically re-
turn to the Display Priority showing either NO NAME or
the station name.
Tip
Frequency Display is initially set to the Display Priority,
and Station Name (NO NAME) is set to the Tempo-
rary indicator.
Display Priority can be set for the following items;
Radio mode
Frequency
Station name
CDC (CD changer) mode
Disc name
Disc No/Track No/Elapsed track time
CD or other media
TRACK/TIME : Track No, and elapsed time scrolls.
SONG NAME : Song name scrolls.
ALBUM TITLE : Album title scrolls.
ARTIST NAME : Artist name scrolls.
SCROLL : ID-3Tag (Song/Album/Artist) scrolls.
FOLDER NAME : Folder name scrolls.
FILE NAME : File name scrolls.
Switching the Source (Selecting auxiliary
input)
You can connect the auxiliary equipment (Portable cassette
player, etc) to this radio via optional AUX-IN cable. (See page
20) Each time the
CD
is pressed, the operation source will
change over as shown below;
CDRADIO
CD changer or AUX
Press the
BND / TS
to return to radio mode.
Note
If the
CD
button is pressed when no CD has been loaded
into the unit, The CD mode will skip to the CD changer mode
or AUX mode.
Also, if the CD changer is not connected, the system will move
across to the AUX mode regardless of whether auxiliary equip-
ment is connected or not (AUX will be displayed.)
It is not possible to switch to the AUX mode when the CD
changer is connected.
San Jose MP41_body_en 8/28/01, 6:04 PM5
ENGLISH
E-6
The items supported for display priority for each media are as
shown in the table below.
When an item that is not supported is selected, NO NAME
is displayed, following which TRACK/TIME is displayed.
Media
CD
DISP Priority
CD
TEXT
MP3 WMA
ID3-Tag Scroll
✕✕
FOLDER NAME ✕✕
FILE NAME ✕✕
TRACK/TIME ✕✕
ID3-Tag MUSIC ✕✕
ID3-Tag ALBUM ✕✕
ID3-Tag ARTIST
Display Speed selection
The scroll speed of the display indication can be switched.
You can select :
SLOW : Slow.
FAST : Fast.
1. Repeatedly press the
DISP
to display the DISP. SPEED
on the display window.
2. Rotate the dial to select the desired display speed.
Display Scroll type selection
The scroll type of the display indication can be switched.
You can select :
ROLLING : Scrolls across the display.
WITH PAUSES : Scrolls across the display with pause.
1.
Repeatedly press the
DISP
to display the SCROLL TYPE
on the display window.
2. Rotate the dial to select the desired scroll type.
Level Meter selection
The meter displays can be selected from four types.
You can select :
METER 1 : The level meter goes upward.
METER 2 : Only the very top segment lights.
METER 3 : The remaining segments light. (opposite of
METER 2)
METER 4 : The level meter goes up and down dividing
from the center segment.
METER 0 : No meter is indicated.
1. Repeatedly press the
DISP
to display the METER 1 on
the display window.
2. Rotate the dial in a clockwise direction to select the de-
sired meter indication.
METER 1 METER 2 METER 3 METER 4 ME-
TER 0
Level Meter Sensitivity selection
The sensitivity of the level meter display can be switched.
You can select :
LEVEL 1 : Normal sensitivity.
LEVEL 2 : High sensitivity.
1. Repeatedly press the
DISP
to display the LEVEL 1 on
the display window.
2. Rotate the dial to select the desired meter sensitivity.
SLOW
FAST
ROLLING
WITH PAUSES
LEVEL 1
LEVEL 2
R-ch Level meter
L-ch Level meter
*1
*2
Notes
*1:
MUSIC
ALBUM
*2:
MUSIC
ALBUM ARTIST
San Jose MP41_body_en 8/28/01, 6:04 PM6
ENGLISH
E-7
Display Contrast selection
The contrast of the display can be adjusted.
You can adjust :
10 ~ 0 ~ +10
1. Repeatedly press the
DISP
to display the CONTRAST
on the display window.
2. Rotate the dial to select the desired display contrast.
Message ON/OFF selection
Message display following POWER ON/OFF can be switched.
You can adjust :
MESSAGE ON : A message is displayed following power
on/off.
MESSAGE OFF : No message is displayed.
1.
Repeatedly press the
DISP
to display the MESSAGE ON
on the display window.
2. Rotate the dial to select whether or not to display a mes-
sage following power on/off.
How to defeat Demo Mode
After installation we recommend defeating the Demo Mode.
When power is turned off, the unit switches to demonstration
mode.
The demonstration starts about 10 seconds after power off.
The demonstration of each function is repeatedly shown on
the display screen.
You can adjust :
DEMO ON : The demonstation is displayed after
power off.
DEMO OFF : A demonstration is not displayed after
power off.
1. Repeatedly press the
DISP
to
display the DEMO ON.
2. Rotate the dial to select whether or not the demonstra-
tion should be displayed when power is off.
+ 10
10
ON
OFF
Enhancing the bass sound
For extended bass centered @ 72Hz, Blaupunkts XBASS func-
tion can be set for either each band and CD/MP3/CDC/AUX
mode.
You can select :
XBASS 1 : Enhanced BASS level (low).
XBASS 2 : Enhanced BASS level (Middle).
XBASS 3 : Enhanced BASS level (High).
XBASS 4 : Enhanced BASS level (Very high).
XBASS 0 : No BASS enhanced.
Press the
XBASS
repeatedly to select the bass sound.
appears on the display window. (Except for XBASS 0)
Each time you press
XBASS
, the current mode appears on
the display window and the mode change as follows:
XBASS 0 XBASS 3XBASS 2 XBASS 4XBASS 1
Note
Reduce XBASS level if your combination of speakers and add-
on amplifiers sound distorted at the preferred sound level.
DEMO ON
DEMO OFF
San Jose MP41_body_en 8/28/01, 6:04 PM7
ENGLISH
E-8
Turn on/off message edit
You can edit the turn on/off message and store it in memory.
Following four messages can be edit with 12 characters each.
When you turn on the unit, MESSAGE 1 will be displayed
then MESSAGE 2 will momentarily displayed before actual
power on.
When you turn off the unit, MESSAGE 3 will be displayed
then MESSAGE 4 will momentarily displayed before actual
power off.
Turn-on message
MESSAGE 1 / MESSAGE 2
Turn-off message
MESSAGE 3 / MESSAGE 4
1. Repeatedly press the
DISP
to display the MESSAGE ON
on the display window.
2. Press the
MUTE / SENS
to flash the MESSAGE 1.
3. Rotate the dial to select the desired message you want
to edit.
MESSAGE 1 MESSAGE 2 MESSAGE 3 MES-
SAGE 4
4. Press the
MUTE / SENS
, then enter the character.
A. Rotate the dial in a clockwise direction to select the
desired characters.
(A~Z, a~z, 0~9, ( )
∗ + , − . / ! # $ % & : ; < = > ?
@ [ \ ] ˆ _ ` { } ˜ )
B. Press the
TUN/TRK
to move the flashing cursor to
the next position. If you press
TUN/TRK
, the flashing
cursor moves to the left.
C. Repeat steps A. and B. to complete entering the en-
tire message 12 characters max.
Tips
To erase/correct a message, press the
DISP
for more
than 2 seconds to clear the character and re-enter.
When entering a name, pressing the following but-
tons affects the display of characters as follows:
1
: Changes to inputting letters. (Starts with A.)
If pressed while letters are already selected,
switches between upper and lower case letters.
2
: Changes to inputting numbers. (Starts with 0.)
3
: Changes to inputting symbols. (Starts with (.)
6
: Enters a space (blank).
5. Press the
MUTE / SENS
to store the message.
The new message flashes.
6. To return to the normal radio reception, Press
DISP
.
Notes
If you make no button input or dial operation in 20 sec-
onds, the message edit mode will turn off automatically.
Make sure the MESSAGE will be ON .
Erasing the turn on/off message
You can erase the turn on/off message if so desired.
1. Repeatedly press the
DISP
to display the MESSAGE ON
on the display window.
2. Press the
MUTE / SENS
to flash the message you edit.
3. Rotate the dial to select the desired message you want
to erase.
4. Press the
DISP
for more than 2 seconds.
Repeat steps 1. and 3. if you want to erase other mes-
sage.
5. To return to the normal radio reception, Press
DISP
.
San Jose MP41_body_en 8/28/01, 6:04 PM8
ENGLISH
E-9
Radio Reception
Receiving the Memorized Stations
1. Press the
BND / TS
to select the desired AM or FM band.
2. Press the
1
-
6
momentarily.
Local/Distant (LO/DX) Selection
This feature is used to select the signal strength at which the
radio will stop during Seek Tuning.
Press the
MUTE / SENS
for more than 2 seconds to select the
Local setting and only strong (local) stations will be received.
The lo indicator appears on the display window.
Pressing for more than 2 seconds again will select the Dis-
tant setting and the radio will stop at a wider range of signals,
including weaker more distant stations. The lo indicator will
go out on the display window. DX is the suggested default
setting.
Preset Scan Tuning
1. Press the
BND / TS
to select the desired AM or FM band.
2. Hold the
SC/PS
pressed for more than 2 seconds.
SCAN indicator will appear on the display window.
The unit will scan preset memory for the 12 stations from
the AM/AMT band or the 18 stations from the FM1/FM2/
FMT bands. The unit will stop at each preset station for 8
seconds, before continuing to the next preset station.
Press the
SC/PS
again to stop Preset Scan Tuning and
remain this on the selected frequency.
Memorizing Stations Automatically (Travel Store)
1. Press the
BND / TS
to select the desired AM or FM band.
2. Hold the
BND / TS
pressed for longer than 2 seconds.
Up to 6 stations with strong signals will be automatically
stored in preset memory for the selected band.
If the radio is in FM1 or FM2, it switches to FMT. If the
radio is in AM, it switches to AMT.
Note
This function is available for FMT and AMT.
Memorizing Only the Desired Stations
You can store up to 6 stations on each band (18 for FM1, FM2
and FMT, 12 for AM and AMT) in the order of your choice.
1. Press the
BND / TS
to select the desired band.
2. Press the
TUN/TRK
to tune in stations.
3. Press and hold the desired preset memory button
1
-
6
for about 2 seconds until the frequency indicator
flashes twice.
The number of the pressed preset memory button ap-
pears on the display window.
Note
If when you store another station on the same preset number
button, the previously stored station is replaced with new one.
Seek Tuning
1. Press the
BND / TS
to select the desired AM or FM band.
FM1 FM2 FMT AM AMT
(FMT & AMT are Travel Store bands.)
2. Press the
TUN/TRK
to tune in stations. Tuning automati-
cally stops at a broadcasting frequency.
When tuned in to FM stereo broadcasting stations, the
stereo signal indicator will appear on the display
window.
Manual Tuning
1. Press the
BND / TS
to select the desired AM or FM band.
2. Press the
TUN/TRK
or
TUN/TRK
for more than 0.5 second
to activate the manual tuning mode. Press again to tune in
to stations.
MAN will appear on the display window.
After 4 seconds of completing Manual Tuning, the tuning
control will revert to the Seek Tuning mode.
Scan Tuning
1. Press the
BND / TS
to select the desired AM or FM band.
2. Hold the
SC/PS
pressed for less than 2 seconds.
The unit will scan the selected band for stations.
SCAN indicator will appear on the display window. The
unit will stop at each station for 8 seconds, before con-
tinuing to the next station.
Press the
SC/PS
again to stop Scan Tuning and remain
this on the selected frequency.
Tip
While tuning, the pie-shaped signal-strength meter
on the display is lit differently depending on the strength
of the signal. While scanning bands, the pie-shaped sig-
nal-strength meter spins. While playing CDs, this display
also spins.
San Jose MP41_body_en 8/28/01, 6:04 PM9
ENGLISH
E-10
Storing the station names
You can assign a name to each radio station and store it in
memory. As much as 30 station names can be stored com-
posed with 12 characters each.
Storing the station names
1. Tune in a station whose name you want to store.
2. Press the
DISP
for more than 2 seconds.
The NAME EDIT will light then the _ _ _ _ _ _ _ _ _ _ _
_ on the display window. The first _ flashes.
3. Enter the characters.
A. Rotate the dial in a clockwise direction to select the
desired characters.
(A~Z, a~z, 0~9, ( )
∗ + , − . / ! # $ % & : ; < = > ?
@ [ \ ] ˆ _ ` { } ˜ )
B. Press the
TUN/TRK
to move the flashing cursor to
the next position. If you press
TUN/TRK
, the flashing
cursor moves to the left.
C. Repeat steps A. and B. to complete entering the en-
tire name 12 characters max.
Tips
To erase/correct a name, press the
DISP
for more
than 2 seconds to clear the character and re-enter.
When entering a name, pressing the following but-
tons affects the display of characters as follows:
1
: Changes to inputting letters. (Starts with A.)
If pressed while letters are already selected,
switches between upper and lower case letters.
2
: Changes to inputting numbers. (Starts with 0.)
3
: Changes to inputting symbols. (Starts with (.)
6
: Enters a space (blank).
4. Press the
MUTE / SENS
to store the station name.
The station name flashes.
5. To return to the normal radio reception, Press
DISP
.
Note
If you try to store more than 30 station names,
✳✳
FULL
✳✳
will be displayed.
Erasing the station names
1. Tune in any station and press the
DISP
for more than 2
seconds.
2. Press the
MUTE / SENS
.
The station name or _ _ _ _ _ _ _ _ _ _ _ _ flashing.
3. Rotate the dial to select the name of the station that you
want to erase. To erase all the names of the stations, dis-
play ALL DELETE.
4. Press the
DISP
for more than 2 seconds.
Repeat steps 3. and 4. if you want to erase other names.
5. To return to the normal radio reception, Press
DISP
.
Direct Access to Memorized Stations via
Station call
You can search for the memorized AM & FM station names in
the memory.
1. Press the
DISP
to display the STATION CALL on the
display window.
2. Rotate the large dial to select the desired station name.
3. Press the
MUTE / SENS
to tune in the desired station.
San Jose MP41_body_en 8/28/01, 6:04 PM10
ENGLISH
E-11
Listening to a disc that is already loaded
Press the
CD
to select the CD mode.
Playback begins automatically.
Pausing Playback
Press the
6/
.
To resume playback, press the
6/
again.
Stopping Playback
Press the
BND / TS
to select the radio reception (FM1,FM2,
FMT or AM, AMT).
Ejecting Discs
Press the to eject the disc located behind flip-down front
panel.
Notes
The unit will turn on automatically when a CD is inserted if
the ignition switch is ‘‘ON’’.
When the disc is ejected from the CD slot, remove it within
10 seconds; otherwise, the disc will be reloaded automati-
cally.
Track Search
Press the
TUN/TRK
during CD mode. Track numbers appear
in the display window.
: Playback starts from the beginning of the next track.
: Playback starts from the beginning of the current track.
Press again to play the previous track.
Cue / Review
Press and hold the
TUN/TRK
. Release when you have found
the desired point.
: To search forward.
: To search backward.
Scan Play
Press the
SC/PS
during CD mode.
The ‘‘SCAN 1’’ indicator appears in the display window. This
will play the first 10 seconds of all the tracks on the disc.
Press the
SC/PS
again to cancel this feature.
Repeat Play
Press the
5/RPT
during CD mode.
The ‘‘RPT 1’’ indicator appears in the display window and the
current track is played repeatedly.
Press the
5/RPT
again to cancel this feature.
Mix Play
Press the
4/MIX
during CD mode.
The ‘‘MIX 1’’ indicator appears in the display window.
All the tracks on the current disc are played in random order.
Press the
4/MIX
again to cancel this feature.
Note
If the Mix, Repeat or Scan buttons are pressed for 2 seconds
or longer while playing a music CD, the unit will enter the
respective mode2. These modes can be used for playing MP3
discs which contain a number of folders. (See page 14.)
Since a music CD is treated as a folder, there is almost no
difference in the operation.
CD Operations
Playing the CD player
Loading Discs
1. Press the
OPEN
and insert the disc.
2. Close the front panel. ‘‘LOADING’’ and ‘‘FILE CHECK’’ will
appear in the display window.
Playback begins automatically.
Note
Make sure that the front panel is closed when playback be-
gins.
Playback with the front panel open causes the
unit to turn off automatically in about 10 min-
utes.
! NEVER Insert a 3-inch CDs.
This unit is designed for playback of standard 5-inch CDs
only. Do not attempt to use 3-inch CD singles in this unit,
either with or without an adaptor, as damage to the player
and/or disc may occur.
Tips
When a CD is loaded, the
on the display remains lit.
During playback of a CD, the pie-shaped signal-strength
meter
spins.
Labeled side up
San Jose MP41_body_en 8/28/01, 6:04 PM11
ENGLISH
E-12
CD Changer Controls
Storing the CDC disc names
You can label each disc with a personalized name. As many
as 99 disc names can be stored, composed with 7 characters
each.
Storing the CDC disc names
1. Play the CD and press the
DISP
for more than 2 sec-
onds. The NAME EDIT will light then the _ _ _ _ _ _ _
on the display window. The first _ flashes.
2. Enter the characters.
A. Rotate the dial in a clockwise direction to select the
desired characters.
( A~Z 0~9 ( )
∗ + , − . / )
B. Press the
TUN/TRK
to move the flashing cursor to
the next position. If you press
TUN/TRK
, the flashing
cursor moves to the left.
C. Repeat steps A. and B. to complete entering the en-
tire name 7 characters max.
Tips
To erase/correct a name, press the
DISP
for more than
2 seconds to clear the character and re-enter.
When entering a name, pressing the following but-
tons affects the display of characters as follows:
1
: Changes to inputting letters. (Starts with A.)
If pressed while letters are already selected,
switches between upper and lower case letters.
2
: Changes to inputting numbers. (Starts with 0.)
3
: Changes to inputting symbols. (Starts with (.)
6
: Enters a space (blank).
3. Press the
MUTE / SENS
to store the disc name.
The disc name flashes.
4. To return to the normal CD playback mode, Press
DISP
.
Playing the CD Changer
This product can control a CD changer. Please check with
your nearest car stereo specialist for recommendations of the
models that will work with this radio (See page 1).
Press the
CD
to switch the CD changer mode. Disc No,
Track No, and Track time appear on the display window and
playback begins automatically. Press again to change back to
built-in CD operation.
Disc Select
Press the Disc select buttons to select the desired disc for
play.
FOLDER +
: To advance to a higher number disc.
FOLDER
: To return to a lower number disc.
Track Search
Press the
TUN/TRK
.
Track numbers appear in the display window.
: Playback starts from the beginning of the next track.
: Playback starts from the beginning of the current track.
Press again to play the previous track.
Cue / Review
Press and hold the
TUN/TRK
. Release when you have found
the desired point.
: To search forward.
: To search backward.
Track / Disc Scan Play
Track Scan
Press the
SC/PS
.
The SCAN ON indicator appears in the display window. This
will play the first 10 seconds of all the tracks on all the discs.
Press the
SC/PS
again to cancel this feature.
Disc Scan
Press the
SC/PS
for more than 2 seconds.
The ‘‘SCANDISC ON’’ indicator appears in the display win-
dow. This will play the first 10 seconds of the first track on
each disc. Press the
SC/PS
again to cancel this feature.
Track / Disc Repeat Play
Track Repeat
Press the
5/RPT
.
The ‘‘RPT ON’’ indicator appears in the display window and
the current track is played repeatedly.
Press the
5/RPT
again to cancel this feature.
Disc Repeat
Press the
5/RPT
for more than 2 seconds.
The ‘‘RPTDISC ON’’ indicator appears in the display window
and the current disc will be continually repeated.
Press the
5/RPT
again to cancel this feature.
Track / Disc Mix Play
Track Mix
Press the
4/MIX
.
The ‘‘MIX ON’’ indicator appears in the display window.
All the tracks on the current disc are played in random order.
Press the
4/MIX
again to cancel this feature.
Disc Mix
Press the
4/MIX
for more than 2 seconds.
The ‘‘MIXDISC ON’’ indicator appears in the display window.
Both discs and tracks will be played in random order.
Press the
4/MIX
again to cancel this feature.
Tip
During Disc scan, Disc Repeat or Disc Mix, the
will be lit
on the display.
San Jose MP41_body_en 8/28/01, 6:04 PM12
ENGLISH
E-13
Erasing the CDC disc names
1. Press the
DISP
for more than 2 seconds during CD
changer mode.
2. Press the
MUTE / SENS
.
The disc name or _ _ _ _ _ _ _ is now flashing.
3. Rotate the dial to select the name that you want to erase.
To erase all the names, display ALL DELETE .
4. Press the
DISP
for more than 2 seconds.
Repeat steps 3. and 4. if you want to erase other names.
5. To return to the normal CD playback mode, Press
DISP
.
Direct Access to Memorized Disc Names via
Disc call
You can search for the memorized disc names in the memory.
1. Press the
DISP
to display the DISC CALL on the display
window.
2. Rotate the large dial to select the desired disc name.
3. Press the
MUTE / SENS
to start playback for the desired sta-
tion.
IDC A09 Changer:
The IDC A09 is a 5-disc CD Changer. When using the Folder
+ & keys, it is possible to mistakenly ask the IDC A09 for a
CD Disc higher than the number 5 (Five).
When this command is manually done in error, the San joses
Display will read disc numbers above 5, but the unit will then
only play but a few seconds of the next disc, which would be
Disc 1, whereas the Display is reading disc number 6 (Six)
which does not exist. Choosing a vacant / empty IDC A09
disc slot will result in a No Magazine or a double dashes
( ) message in the LCD.
Do one of the following remedies:
Manually select the desired disc at the Changers controls,
Or allow the IDC A09 to automatically cycle to the next disk
after the completion of Disc #5,
Or Press Folder + or until Disc 1 (One) or the desired disc is
displayed in the receivers LCD.
San Jose MP41_body_en 8/28/01, 6:04 PM13
ENGLISH
E-14
MP3 / WMA operation
You can play MP3 and WMA files written on CD-ROMs, CD-
Rs, or CD-RWs by following the procedures below.
In this section, track and album mean MP3 or WMA file
and folder in PC terminology, respectively.
MP3 / WMA play
Loading Discs
1. Press the
OPEN
and insert a CD-ROM, CD-R, or CD-RW
with the labeled side upward.
2. Close the front panel.
During scanning of the disc, ‘‘LOADING’’and ‘‘FILE CHECK’’
appear in the display window.
Playback begins automatically.
CD-R/RW with very complex folder trees could take in the
range of 20-seconds to load.
Listening to a disc that is already loaded
Press the
CD
to select the CD mode.
Playback begins automatically.
Pausing Playback
Press the
6/
.
To resume playback, press the
6/
again.
Stopping Playback
Press the
BND / TS
to select the radio reception (FM 1, FM 2,
FT or AM, AT).
Ejecting Discs
Press the to eject the disc located behind the flip-down
front panel.
Notes
The unit will turn on automatically when a CD is inserted if
the ignition switch is ‘‘ON’’.
When the disc is ejected from the CD slot, remove it within 10
seconds; otherwise, the disc will be reloaded automatically.
ID3 Tags are not supported for WMA files.
Track Search
Press the
TUN/TRK
during CD mode. Track numbers appear
in the display window.
: Playback starts from the beginning of the next track.
: Playback starts from the beginning of the current track.
Press again to play the previous track.
Album(Folder) Search
Press the
FOLDER +
or
FOLDER
during CD mode. Folder indica-
tor
flashes in the display window.
FOLDER +
: Playback starts from the beginning of the next folder.
FOLDER
: Playback starts from the beginning of the previous
folder.
Cue / Review
Press and hold the
TUN/TRK
. Release when you have found
the desired point.
: To search forward.
: To search backward.
Scan / Folder Scan Play
Scan Play (Mode1)
Press the
SC/PS
during CD mode.
The ‘‘SCAN 1 ON’’ appears in the display window. This will
play the first 10 seconds of all the tracks on the disc.
Press the
SC/PS
again to cancel this feature.
Folder Scan Play (Mode2)
Press the
SC/PS
for more than 2 seconds during CD mode.
The ‘‘SCAN 2 ON’’ appears in the display window. This will
play the first 10 seconds of first tracks in each folder.
Press the
SC/PS
again to cancel this feature.
Repeat / Folder Repeat Play
Repeat Play (Mode1)
Press the
5/RPT
during CD mode.
The ‘‘RPT 1 ON’’ appears in the display window and the cur-
rent track is played repeatedly.
Press the
5/RPT
again to cancel this feature.
Folder Repeat Play (Mode2)
Press the
5/RPT
for more than 2 seconds during CD mode.
The ‘‘RPT 2 ON’’ appears in the display window and the cur-
rent folder is played repeatedly.
Press the
5/RPT
again to cancel this feature.
Mix Play / Folder Mix
Mix Play (Mode1)
Press the
4/MIX
during CD mode.
The ‘‘MIX 1 ON’’ appears in the display window.
All the tracks on the current folder are played in random or-
der. Press the
4/MIX
again to cancel this feature.
Folder Mix Play (Mode2)
Press the
4/MIX
for more than 2 seconds during CD mode.
The ‘‘MIX 2 ON’’ appears in the display window.
All the tracks on the current disc are played in random order.
Press the
4/MIX
again to cancel this feature.
ID3 Tag Jump
When a file containing an ID3 Tag is played, pressing
3/JUMP
immediately switches the unit to ID3 Tag scroll display.
When the scroll display finishes, the original display is restored.
When pressed
3/JUMP
while scroll display has priority, the origi-
nal display is restored after displaying TRACK/TIME for five
seconds.
Tip
When playing a file that does not contain an ID3 Tag or when
playing a WMA file, pressing
3/JUMP
causes NO NAME to be
displayed.
San Jose MP41_body_en 8/28/01, 6:04 PM14
ENGLISH
E-15
This unit can play back files recorded in MP3 or WMA format
on CD-ROM, CD-R (recordable) or CD-RW (rewritable) discs.
There are some limitations on the files and media that can be
used, so before recording files on a disc please carefully read
the following information.
ISO9660 Format
The unit can play back data recorded in ISO9660 format.
ISO9660 is an international standard for representative CD-
ROM file formats determined by ISO (International Standard
Organization).
The media formats that can be used by the unit include Level
1, Level 2 and the extension format known as Joliet.
What are MP3 and WMA?
An MP3 file stores audio data compressed using the MPEG
1 / 2 audio layer-3 file format. We call files that have the
.mp3 extension MP3 files. Likewise for WMA files. WMA
is an abbreviation for Windows Media Audio. WMA files have
the extension .wma and are compatible with MP3 files.
The unit cannot read files that have a file extension differ-
ent from .mp3 or .wma.
The unit cannot read files without an extension even if the
files are MP3 or WMA files.
Furthermore even if a file has an .mp3 or .wma exten-
sion, the unit cannot read the file if is not recorded with the
MP3 or WMA data format.
Playback Limitations
The number of tracks and number of albums (folder) that
can be played back from a disc are as follows.
Tracks : About 250 depending on file contents.
Albums(folder) :
A maximum of 250 depending on the num-
ber of tracks.
The unit also recognizes up to eight album(folder) levels.
The unit can playback MP3 files with compression bit rates
from 32kbps~320kbps. However for the best balance of file
space and sound quality we recommend 128kbps. When
files compressed at less than 128kbps are played back, the
sound may have breaks in it.
Sampling rates are supported as follows.
MPEG 1 48k 44.1k 32k
MPEG 2 24k 22.05k 16k
MPEG 2.5 12k 11.03k 8k
In the case of WMA files, play back is possible only for files
encoded with a compression bit rate of at least 64kbps and
a sampling rate of 44.1 kHz.
Please note that the unit cannot play files encoded using
the WMA copyright protection function.
When playing WMA files, song, album and artist tags can-
not be displayed.
The unit allows the playback of CD-R and CD-RW discs
containing a mixture of music CD data (CD-DA), MP3 and
WMA files. However playback of both types of data is pos-
sible only for Mixed Mode CDs/CD Extra created using Disc
at Once Method. (See below.)
The unit also supports files compressed using VBR (vari-
able bit rate).
The unit does not always play back MP3 and WMA files in
the order in which they were recorded.
When many folders are recorded on a disc, the time required
to fetch information from the disc becomes longer.
We recommend that multi-session discs be limited to 10 sessions.
The packet write method is not supported.
The following three methods are used to record data (files)
on a disc. As the unit does not support the Packet Write
method please be aware of this.
The unit supports discs recorded with the Disc at Once and
Track at Once methods.
Disc at Once Method
With this method, all the data to be written is prepared in ad-
vance and then recorded on the disc in one go. Additional
writing of data is not possible.
Track at Once Method
With this method, data is written in file (track) units. Addi-
tional writing of data is possible.
Packet Write Method
With this method, tracks are sub-divided into packets depend-
ing on availability of space on the disc. Additional writing of
data is possible.
Display Information Limitations
The unit can display folder and file names, ID3 Tags of length
up to 64 characters including the extension. However, cer-
tain special symbols may not display correctly.
During playback of MP3 and WMA files, there may be occa-
sions when the elapsed playback time is not correctly dis-
played.
Important Points
Please take care not to append the extensions for MP3 and
WMA files onto files of any other type. When a disc contain-
ing such files is played, the files will be incorrectly recog-
nized and played back. This will result in extremely loud noise
that may damage the speakers.
Depending on the state of the disc or recorder or writing
software used to write on the disc, there may be cases when
the disc cannot be correctly played back. In such cases
please refer to the user manual for the tools you are using.
When using a Macintosh personal computer, the file exten-
sion will not be added, so please add the extension .mp3
to the end of the file name.
This unit does not support WAVE files.
This unit does not support m3u playlists.
The unit does not support Emphasis. (See Glossary on
page 17.)
MP3 / WMA Overview
San Jose MP41_body_en 8/28/01, 6:04 PM15
ENGLISH
E-16
Note Concerning Bit Rate and Record Time
Please refer to the following general guide concerning the bit
rate used when encoding and the overall time of a file re-
corded on disc.
Before recording on a disc, please carefully read the soft-
ware instructions and ensure you use it correctly.
Note
When the sampling frequency used for encoding is 44.1kHz
For highest
320kbps About 4hr
sound quality
CD quality
192 kbps About 7hr
(High sound quality)
CD quality
160 kbps About 8hr
(Medium sound quality)
CD quality
128 kbps About 10hr
(Standard)
When Creating Discs
Files will not always be played back in the order in which they
were recorded. When you want to ensure that files will be
played back in the order they were recorded, please write
onto the disc paying attention to the points below.
Use writing software that can write MP3/WMA files on the
disc in the order of the file (track) names. Please check with
the software developers concerning the behavior and op-
eration of the writing software.
Prefix numbers to the names of folders (albums) and files
(tracks) to arrange them in order. Shown below is a good
example (2 or three digits correctly entered.) and a bad ex-
ample (if the number of digits is not the same for all names,
the names will not be ordered correctly.)
Example
<good> <bad>
01XXXX.mp3 1XXXX.mp3
02XXXX.mp3 10XXXX.mp3
03XXXX.mp3 11XXXX.mp3
04XXXX.mp3 2XXXX.mp3
About Recommended CD-R and CD-RW Media
With some CD-R and CD-RW media, data may not be prop-
erly written depending on their manufacturing quality. In this
case, data may not also be reproduced correctly. We recom-
mend the media manufactured by the following companies:
CD-R Media
TDK USA Corp., Taiyo Yuden (U.S.A.), Inc., Ricoh Corpora-
tion, Eastman Kodak Company, Maxell Corporation of
America, Mitsubishi Chemical Corporation, Fuji Photo Film
U.S.A., Inc., Mitsui Chemicals, Inc., Sony Corporation of
America, Philips Electronics North America Corporation,
Imation Corp.
CD-RW Media
TDK USA Corp., Ricoh Corporation, Mitsubishi Chemical
Corporation
Several types of CD-R and CD-RW media are available, such
as 2X and 1X-4X. Please read the instruction manuals of the
drive and the recording software you are using to select the
right media.
San Jose MP41_body_en 8/28/01, 6:04 PM16
ENGLISH
E-17
Glossary
Bit rate
The bit rate expresses the amount of information transferred
per second as a number of bits. The greater the quantity of
information, the higher the bit rate.
The unit is bits/second. kbps indicates kilo (1,000) bits/
second.
Emphasis
The software used for recording has an emphasis capabil-
ity, which when turned on writes emphasis attributes on to
the audio track. When the emphasis bit is set the sound has a
smooth characteristic. However, at the current time almost all
CD players lack support for this function. It is no problem to
play back an audio track recorded with emphasis on with a
player not supporting emphasis.
Extension
In Windows and DOS personal computers, several charac-
ters are placed at the end of each file name to indicate the
type of file.
The extension consists of a period followed by three alphanu-
meric characters. The extension differs depending on file type.
The extension for MP3 files is .mp3.
ID3 Tags
This is a data format that allows a file name, title and artist
name etc. to be added to MP3 files.
This unit supports SONG ALBUM and ARTIST for Versions
1.0/1.1/2.2 and 2.3.
ID3 Tags are not supported for WMA files.
Multi-Session
When data is written on a CD-R disc, the data written from
the time writing starts until the time writing finishes is regarded
as a bundle called a session. The Track at Once Method al-
lows data to be added to a single disc one track at a time,
with each recording of a track being a single session.
The term multisession refers to the method of recording the
data for two or more sessions on a single disc. We recom-
mend that this unit be used for up to 10 sessions.
Structure of Folder Hierarchy
To keep data within a computer organized, related files may
be put into a folder, but in addition to files, a folder may also
have other folders put into it. Folder B may be put into folder
A, and folder C may be put into folder B so as to create a
hierarchical structure. The number of hierarchical levels that
can be recognized differs depending on the computer operat-
ing system. ISO9660 specifies up to 8 levels.
VBR (Variable Bit Rate)
MP3 files are normally encoded with a fixed bit rate (eg
128kbps etc.), however VBR encoding during which the bit
rate is varied while encoding is also possible. That is to say,
during periods of violent variation of sound the bit rate is in-
creased and during soundless periods the bit rate is de-
creased. Encoding in this way allows file size to be curbed
while maintaining high sound quality. However, some players
do not support VBR, so caution is required when using VBR.
Types of CD
Audio CD(CD-DA)
This is the format used for audio CDs that can be played on
ordinary audio CD players. It is also called CD-DA (Com-
pact Disc Digital Audio).
ISO9660 Format CD-ROM
ISO9660 is a CD-ROM standard file system determined by
ISO (International Organization for Standardization). CD-
ROMs with this format can be played by Windows and
Macintosh operating systems and also by UNIX operating
systems.
HFS Format CD-ROM
This is a CD-ROM conforming to the HFS (Hierarchical File
System) used by Macintosh Mac OS.
Hybrid CD-ROM
This is a CD-ROM containing a mixture of ISO9660 format
files and HFS format files.
Mixed Mode CD
This is a CD-ROM containing both data files and audio files
on the one disc.
Mixed Mode CD is a standard developed for personal com-
puter use so the audio files on the CD cannot be played
with CD players that do not support Mixed Mode CD.
CD Extra (Enhanced CD)
This differs from Mixed Mode CD in that the audio files are
followed on the disc by data files. CD Extra was standard-
ized by Sony and Philips to allow the audio files to be played
with an audio CD player and the data files to be read by a
personal computer.
San Jose MP41_body_en 8/28/01, 6:04 PM17
ENGLISH
E-18
or
,
hold for
2 seconds
(Direct access mode) (select) (set)
Remote control
unit rear surface
Removing the battery insulation sheet
If an insulation sheet is attached to the remote control unit,
make sure to remove the insulation sheet before use. In this
case, the batteries will already be inside and can be used
immediately.
Inserting Batteries
1. Push A in the direction of the arrow while holding B and
pull out.
2. Confirm that the (+) (
-
) terminals are correctly aligned
and insert the lithium battery (CR2025).
3. Push in the battery case until a click can be heard.
Battery case
A
B
Operation
Operate while facing towards the sensor of the main unit.
* Press and hold
** Press and hold for 2 seconds
Switching the Source
The mode will switch each time the SRC button is pressed.
Direct Access
For direct access during radio mode or CDC mode, use the
following operations.
Radio
CD
CDC or AUX
Precautions on battery use
Always use lithium batteries (CR2025).
Warning
Use the lithium batteries properly
(1) Never recharge, short circuit, disassemble, modify, heat
or place in fire. This may result in fire, generation of heat
or explosion.
(2) Place batteries out of reach of infants. If accidentally swal-
lowed, consult a physician immediately.
(3) Use tape to insulate whenever disposing or storing batter-
ies. Contact with metals or other batteries may result in
fire or explosion.
Caution
Properly align the battery (+) (
-
) terminals
Improper handling of batteries may cause fluid leakage or
explosions and may result in damage to the device or in-
jury.
Align the battery (+) (
-
) terminals correctly.
Do not leave the remote control unit in high temperature
such as from direct sunlight. It results in the deformation of
the case, leakage of battery acid, and so on.
Do not expose remote to water, damage may result.
Insulation Sheet
Lithium battery
(CR2025)
Radio mode
Seek tuning
Preset scan**
Seek tuning
Preset select
Band select
Travel store**
CD mode
Scan play
Track search
Cue/Review*
CDC mode
Scan play
Disc scan**
Disc up
Disc down
Track search
Cue/Review*
Aux
Volume up/down
MP3/WMA
mode
Scan play
Folder scan**
Folder up
Folder down
Track search
Cue/Review*
Handling the RC-823 Remote Control Unit
San Jose MP41_body_en 8/28/01, 6:04 PM18
ENGLISH
E-19
Installations
Supplied Mounting Hardware
Sleeve
Bushing, Locking Mounting Strap Release
Screw screw and Screw Keys
Precautions
Be sure to detach the front panel before you start in-
stalling the unit.
Choose the mounting location carefully so that the unit will
not interfere with the normal driving operations of the driver.
Use only the supplied mounting hardware for a safe and
secure installation.
When mounting the unit in a car, keep the unit as level as
possible. If the unit must be mounted at an angle, due to the
design of the vehicle, make sure that the unit does not tilt
upward by more than 30°.
Turn-off Demo mode before use.
Mounting Example
Installation in the dashboard.
1. Install the sleeve in the dashboard.
2. Select and bend the appropriate tabs to hold the sleeve
firmly in place.
Mounting Strap Use
3. Attaching the Mounting Strap to the underside of the
dash board, using screw.
Attach the back of the unit to the Mounting Strap us-
ing the support stem bolt and hardware.
Bushing Use
3. As shown in the figure below, securely fasten the
screw, which has been inserted into the bushing to
the rear of the set.
Fire wall
The distance to the fire wall var-
ies due to the type of the car. Be
sure to secure the unit by prop-
erly inserting the bushing.
Caution
Insufficient fastening of the
screw may cause some CDs to
skip.
If your car has no accessory position on the
ignition key switch (POWER SELECT switch)
The illumination on the front panel is factory-set to be turned
on even when the unit is not being played. However, this set-
ting may cause some car battery wear if your car has no ac-
cessory position on the ignition key switch. To avoid this battery
wear, set the POWER SELECT switch located on the bottom
of the unit to the B position, then press the RESET button.
The illumination is reset to stay off while the unit is not being
played.
Reset button
Press the reset button with the point of
a sharp object such as a ball-point pen.
POWER SELECT SWITCH
(Located on the bottom of the unit)
Change the position with a jewelers screwdriver, etc.
A : Your car has an accessory position on the ignition
switch.
B : Your car has no accessory position on the ignition
switch.
Be sure to
press the reset button after changing the
switch and connecting the lines.
Note
If set to the
B
position, demonstration mode will be elimi-
nated.
San Jose MP41_body_en 8/28/01, 6:04 PM19
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32

Blaupunkt San Jose MP41 Le manuel du propriétaire

Catégorie
Récepteurs multimédia de voiture
Taper
Le manuel du propriétaire

dans d''autres langues