Blaupunkt San Jose MP41 Le manuel du propriétaire

Marque: Blaupunkt

Modèle: San Jose MP41

Catégorie: Récepteurs multimédia de voiture

Taper: Le manuel du propriétaire

288F0281

SAN JOSE MP41

High-Power FM/AM/CD/MP3 Receiver with Detachable Face

Autoradio FM/AM à Lecteur CD/MP3 de Forte Puissance et à Face Amovible

Receptor FM/AM/Reproductor de CD/MP3 de Alta Potencia y con Panel Extraíble

Rádio FM/AM/CD/MP3 de Alta Potência

com Face Removível

Robert Bosch Corporation

Sales Group —

Blaupunkt Division

2800 South 25th Avenue,

Broadview, Illinois 60155

ENGLISH

FRANÇAIS

ESPAÑOL

PORTUGUÊS

Issue date 08-01

PWR

OPEN

200 WATTS

654321

BND

DISP

SAN JOSE MP41

MUTE

SUB OUT

Important Notice

Prior to Installation, “Demo

Mode” should be defeated.

See page 7.

San Jose MP41_cover 8/23/01, 2:37 PM1

ENGLISH

E-1

Precautions

This equipment has been tested and found to comply with the

limits for a Class B device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable pro-

tection against harmful interference in a residential installa-

tion. This equipment generates, uses, and can radiate radio

frequency energy, and, if not installed and used in accord-

ance with instructions, may cause harmful interference with

radio communications. However, there is no guarantee that

radio interference will not occur in particular installation. If this

equipment does cause harmful interference to radio or televi-

sion reception, which can be determined by turning the equip-

ment off and on, the user is encouraged to consult the dealer

or an experienced radio/TV technician for help.

You are cautioned that any changes or modifications not ex-

pressly approved in this manual could void your authority to

operate this equipment.

Features

• MP3/WMA file playback support

• CD-TEXT support (SONG, ALBUM)

• Detachable flip down front panel

• Built-in power amplifier

(max. output : 50W × 4ch)

• FM/AM PLL Synthesizer tuner

• 30 Station preset memory

• Travel Store / Scan tuning

• X-BASS System

• Station / Disc name store, Station / Disc call

• Auxiliary input

• IR Remote Control RC-823

• CD changer control

(IDCA09, CDCA08 & CDCA071*)

* CDCA071 requires adaptor # 7607 898 093 available

separately.

FCC WARNING

• Avoid installing the unit where it would be subject to high

temperatures, such as in direct sunlight or a hot air stream

from the heater, or where it would be subject to dust, dirt, or

excessive vibration.

• Do not turn on the unit if the temperature inside the car is

very high. Always cool down the unit before usage. Parking

your car in direct sunlight will result in a temperature rise.

• If the unit does not turn on, check the connections first. Then

check whether the fuse at the back of the unit is blown.

• Carefully read this manual before using the unit. If you en-

counter any problems that are not covered in this manual,

please consult the dealer where you purchased the unit or

the dealer nearest to you.

• This unit has been designed specifically for playback of com-

pact discs bearing the following mark. Other discs cannot

be played.

Handling Compact Discs

• Be careful when removing a compact disc after the play-

back is completed because the disc may be extremely hot.

• Do not use non-conventional discs such as heart-shaped,

octagonal discs, etc. The player could be damaged.

• Do not expose compact discs to direct sunlight or any heat

source.

• Check all compact discs before playing, and discard cracked,

scratched or warped discs.

• Wipe dirty or damp discs outward from the centre with a

soft cloth.

• Do not use any solvents such as commercially available

cleaners, antistatic spray, or thinner to clean the compact

discs.

• If a label is affixed to a disc, the label may prevent removal

of the disc from the unit or may damage the unit.

Label

San Jose MP41_body_en 8/28/01, 6:03 PM1

ENGLISH

E-2

Notes

• Be sure to use this unit with the front panel closed.

The unit is automatically switched off when the front panel

is left open for about 10 minutes.

• Do not handle the unit roughly when opening/closing the

front panel.

• Do not put any object or use it like a tray when the front

panel is open in a lying position.

• Do not press OPEN button when closing the front panel.

• Do not put too much force to the operation buttons or the

display window as it may cause damage or deform the unit.

• Connectors on the unit and front panel are vital parts trans-

mitting the signal. Do not touch, push or scratch them.

• Be careful not to pinch your fingers or hands when opening

and closing the front panel.

• Do not press hard on the front panel when affixing it to the

unit. No more than light to moderate pressure should be

needed.

• Make sure there is no dust or dirt on the electrical terminals

on the back of the front panel as this could cause intermit-

tent operation or other malfunctions.

Detaching the Front Panel

EJECT button

3. Close the inner cover.

Do not leave inner cover in the down position unless the

front panel is in place.

2. Pull the front panel toward your direction to remove it.

1. Press the

OPEN

firmly to open the flip down front panel.

Ejecting the CD

Press the recessed button located to the left behind the Front

Panel.

Handling the Front Panel

Attaching the Front Panel

Place the right hand side of the front panel so that the parts

A of the front panel are engaged with the parts B of the unit

as shown below. Then push the left hand side of the front

panel until it is securely locked.

Front Panel Open / Close

Panel open

Press the

OPEN

Panel close

Raise the front panel with your

finger until it locks in place.

Security/Retailer Display

Bolt the front panel with the locking screw (See page 19) in

the inner cover as shown below, to protect the front panel

from theft and from getting lost.

Locking screw

San Jose MP41_body_en 8/28/01, 6:03 PM2

ENGLISH

E-3

Identification of Controls

1 OPEN button

Open the flip down front panel.

2 PWR button

Turns the power of the unit on or off.

3 TUN/TRK button

Used to tune in to the desired station.

4 LCD Display window

5 CD button

Select the operating source (CD, CD changer or AUX).

6 BND/TS button

Selects the AM/FM Band & Travel store.

7 DISP button

Mode selector. Clock adjustment. Display priority setting.

8 MUTE/SENS button

Muting the sound. Switches the seek sensitivity between

local and distance.

9 XBASS button

Boosts the bass sound.

10 PRESET MEMORY button

During radio reception :

; For Preset memory

During CD mode :

4/MIX

; For Mix play (Mix & Mix all during CDC)

5/RPT

; For Repeat play

; For Pause

PWR

OPEN

200 WATTS

654321

BND

DISP

SAN JOSE MP41

MUTE

SUB OUT

11 JUMP button

If an ID3 Tag has been recorded on MP3 file, one touch

switches the unit to ID3 Tag display. (Not supported with WMA.)

12 FOLDER SELECT button

Select the desired CD in CDC (CD changer) mode.

Select the desired FOLDER in MP3/WMA play mode.

13 SC/PS button

Scan tuning. Preset scan tuning. Scan play in CD/CDC mode.

14 AUDIO button

Audio control selector; Bass, Treble, Loudness, Balance

& Fader.

15 Dial

Adjusts the volume level/bass/treble/balance/fader.

Used to store the station names, and selects alpha-nu-

meric characters.

16 Infrared Sensor (behind acrylic facia)

Permits wireless remote control of AM/FM/CD and CD

changer with RC-823 credit card style remote.

Remote Control (Included)

You can operate your receivers basic AM, FM, CD, MP3 &

CDC features via an IR Remote Control, model RC-823.

1011

1314

1 L-ch Level Meter

2 R-ch Level Meter

3 XBASS indicator

4 Main display section

5 STEREO signal indicator

6 Signal-strength indicator

7 lo(Local) indicator

8 MUTE indicator

9 LOUD indicator

10 MIX/RPT/SCAN Mode indicator

11 Clock indicator

12 CD Changer indicator

13 ID-3 Tag indicator

14 DISC IN indicator

15 FOLDER indicator

Flashes when the folder name is displayed.

16 FILE indicator

Flashes when the file name is displayed.

Front Panel

LCD Display

San Jose MP41_body_en 8/28/01, 6:04 PM3

ENGLISH

E-4

General Operations

Turning the power On/Off

Press the

PWR

to turn on or off the unit.

Tip

When you turn on the unit, “BLAUPUNKT MP3 - I WANT MY

MP3!” will be displayed before actual power on.

When you turn off the unit, “BYE - BYE” will be displayed

before actual power off.

You can edit these message. (See “Turn on/off message

edit”)

Volume Level Control and Memory

Rotate the dial to adjust the volume.

It is also possible to set the maximum volume when the power

is switched on by following the procedure explained below.

1. Turn the dial until it is set at the required volume.

2. Press the

PWR

for two or more seconds. The power will

be switched off and the current volume level recorded.

Muting the sound

Press

MUTE / SENS

“MUTE” appears on the display window.

To restore the previous volume level, press

MUTE / SENS

again.

Volume down

Setting the Clock

The clock uses a 12-hour display system. (factory set)

1. Turn the ignition key to the ON position.

2. Press the

PWR

to turn on the unit.

3. Repeatedly press the

DISP

to display “CLOCK 12”.

4. Rotate the dial within 5 seconds to select the 12 or 24-

hour time mode. Each time you rotate the dial, the mode

changes or toggles as follows :

5. Repeatedly press the

DISP

to display “CLOCK ADJUST”.

A. Press the

MUTE / SENS

within 5 seconds to flash the hour digit.

B. Rotate the dial to set the hour digit.

C. Press the

MUTE / SENS

to flash the minute digit.

D. Rotate the dial to set the minute digit.

6. Press the

DISP

momentarily to complete the Clock set-

ting mode.

Note

If you make no button input or dial operation in 20 seconds,

the Clock setting mode will turn off automatically.

Ignition-off Clock Recall

The display will illuminate showing the time and then auto-

matically shut off after 5 seconds.

Press the

DISP

while the ignition switch is in the “OFF” posi-

tion.

CLOCK 24

CLOCK 12

Volume up

Adjusting the Sound Characteristics

1. Press the

AUDIO

to select the desired adjustment mode

as follows;

BASS 0

TREBLE 0

LOUD OFF

(LOUDNESS)

BAL L0 R0

(BALANCE)

FAD R0 F0

(FADER)

2. Rotate the dial to adjust the selected item.

Adjust within 3 seconds after selecting the item. After 3

seconds, the dial reverts to volume control. Use the fol-

lowing tables as a guide for adjusting the settings in each

mode.

Adjustment Range

BASS BASS –5 BASS +5

TREBLE TREBLE –5 TREBLE +5

LOUDNESS LOUD OFF LOUD ON

BALANCE L9 R0 (Full left) L0 R9 (Full right)

FADER R9 F0 (Full rear) R0 F9 (Full front)

Tip

Settings for BASS, TREBLE, LOUDNESS and XBASS can

be made to each of the following modes independently:

FM, AM, CD, MP3, CD Changer and AUX.

San Jose MP41_body_en 8/28/01, 6:04 PM4

ENGLISH

E-5

Mode Selector

Each time the

DISP

is pressed, the display window will change

over as shown below;

Priority indication

STATION(DISC) CALL * : Refer to " Display priority setting "

DSP PRIORITY : Refer to " Display priority setting "

DISP. SPEED : SLOW / FAST

SCROLL TYPE : ROLLING / WITH PAUSES

METER 1 : METER 0 / METER 1 / METER 2 / METER 3 / METER 4

LEVEL 1 : LEVEL 1 / LEVEL 2

CONTRAST : –10 ~ 0 ~ +10

MESSAGE ON : MESSAGE ON / MESSAGE OFF

CLOCK ADJUST : Refer to " Setting the Clock "

CLOCK 12 : Refer to " Setting the Clock "

* : Radio mode only

DEMO ON : Refer to " How to defeat Demo Mode "

Notes

•“STATION CALL” and “DSP priority” are not displayed in

AUX mode.

• If you make no button input or dial operation in few sec-

onds, the display returns priority indication.

Display priority setting

Example

To set Station Name to the Display Priority.

1. Repeatedly press the

DISP

to display “DSP PRIORITY”

appears in the display window.

2. Rotate the dial to select “STATION NAME” or “FRE-

QUENCY”.

3. Hold the

DISP

pressed for more than 2 seconds to con-

firm/enter your selection.

“NO NAME” or a previously assigned station name (See

page 10) flashs once to indicate that Station Name is

selected for the Display Priority.

After 5 seconds, the display mode will automatically re-

turn to the Display Priority showing either “NO NAME” or

the station name.

Tip

Frequency Display is initially set to the Display Priority,

and Station Name (“NO NAME”) is set to the “Tempo-

rary” indicator.

Display Priority can be set for the following items;

• Radio mode

Frequency

Station name

• CDC (CD changer) mode

Disc name

Disc No/Track No/Elapsed track time

• CD or other media

TRACK/TIME : Track No, and elapsed time scrolls.

SONG NAME : Song name scrolls.

ALBUM TITLE : Album title scrolls.

ARTIST NAME : Artist name scrolls.

SCROLL : ID-3Tag (Song/Album/Artist) scrolls.

FOLDER NAME : Folder name scrolls.

FILE NAME : File name scrolls.

Switching the Source (Selecting auxiliary

input)

You can connect the auxiliary equipment (Portable cassette

player, etc) to this radio via optional AUX-IN cable. (See page

20) Each time the

is pressed, the operation source will

change over as shown below;

CDRADIO

CD changer or AUX

Press the

BND / TS

to return to radio mode.

Note

If the

button is pressed when no CD has been loaded

into the unit, The CD mode will skip to the CD changer mode

or AUX mode.

Also, if the CD changer is not connected, the system will move

across to the AUX mode regardless of whether auxiliary equip-

ment is connected or not (“AUX” will be displayed.)

It is not possible to switch to the AUX mode when the CD

changer is connected.

San Jose MP41_body_en 8/28/01, 6:04 PM5

ENGLISH

E-6

The items supported for display priority for each media are as

shown in the table below.

When an item that is not supported is selected, “NO NAME”

is displayed, following which TRACK/TIME is displayed.

Media

DISP Priority

TEXT

MP3 WMA

ID3-Tag Scroll

✕✕

FOLDER NAME ✕✕

FILE NAME ✕✕

TRACK/TIME ✕✕ ✕ ✕

ID3-Tag MUSIC ✕✕

ID3-Tag ALBUM ✕✕

ID3-Tag ARTIST ✕

Display Speed selection

The scroll speed of the display indication can be switched.

You can select :

• SLOW : Slow.

• FAST : Fast.

1. Repeatedly press the

DISP

to display the “DISP. SPEED”

on the display window.

2. Rotate the dial to select the desired display speed.

Display Scroll type selection

The scroll type of the display indication can be switched.

You can select :

• ROLLING : Scrolls across the display.

• WITH PAUSES : Scrolls across the display with pause.

Repeatedly press the

DISP

to display the “SCROLL TYPE”

on the display window.

2. Rotate the dial to select the desired scroll type.

Level Meter selection

The meter displays can be selected from four types.

You can select :

• METER 1 : The level meter goes upward.

• METER 2 : Only the very top segment lights.

• METER 3 : The remaining segments light. (opposite of

METER 2)

• METER 4 : The level meter goes up and down dividing

from the center segment.

• METER 0 : No meter is indicated.

1. Repeatedly press the

DISP

to display the “METER 1” on

the display window.

2. Rotate the dial in a clockwise direction to select the de-

sired meter indication.

METER 1 ➜ METER 2 ➜ METER 3 ➜ METER 4 ➜ ME-

TER 0

Level Meter Sensitivity selection

The sensitivity of the level meter display can be switched.

You can select :

• LEVEL 1 : Normal sensitivity.

• LEVEL 2 : High sensitivity.

1. Repeatedly press the

DISP

to display the “LEVEL 1” on

the display window.

2. Rotate the dial to select the desired meter sensitivity.

SLOW

FAST

ROLLING

WITH PAUSES

LEVEL 1

LEVEL 2

R-ch Level meter

L-ch Level meter

Notes

*1:

MUSIC

ALBUM

*2:

MUSIC

ALBUM ARTIST

San Jose MP41_body_en 8/28/01, 6:04 PM6

ENGLISH

E-7

Display Contrast selection

The contrast of the display can be adjusted.

You can adjust :

• – 10 ~ 0 ~ +10

1. Repeatedly press the

DISP

to display the “CONTRAST”

on the display window.

2. Rotate the dial to select the desired display contrast.

Message ON/OFF selection

Message display following POWER ON/OFF can be switched.

You can adjust :

• MESSAGE ON : A message is displayed following power

on/off.

• MESSAGE OFF : No message is displayed.

Repeatedly press the

DISP

to display the “MESSAGE ON”

on the display window.

2. Rotate the dial to select whether or not to display a mes-

sage following power on/off.

How to defeat Demo Mode

After installation we recommend defeating the Demo Mode.

When power is turned off, the unit switches to demonstration

mode.

The demonstration starts about 10 seconds after power off.

The demonstration of each function is repeatedly shown on

the display screen.

You can adjust :

• DEMO ON : The demonstation is displayed after

power off.

• DEMO OFF : A demonstration is not displayed after

power off.

1. Repeatedly press the

DISP

display the “DEMO ON”.

2. Rotate the dial to select whether or not the demonstra-

tion should be displayed when power is off.

+ 10

– 10

OFF

Enhancing the bass sound

For extended bass centered @ 72Hz, Blaupunkt’s XBASS func-

tion can be set for either each band and CD/MP3/CDC/AUX

mode.

You can select :

• XBASS 1 : Enhanced BASS level (low).

• XBASS 2 : Enhanced BASS level (Middle).

• XBASS 3 : Enhanced BASS level (High).

• XBASS 4 : Enhanced BASS level (Very high).

• XBASS 0 : No BASS enhanced.

Press the

XBASS

repeatedly to select the bass sound.

“

” appears on the display window. (Except for XBASS 0)

Each time you press

XBASS

, the current mode appears on

the display window and the mode change as follows:

XBASS 0 XBASS 3XBASS 2 XBASS 4XBASS 1

Note

Reduce XBASS level if your combination of speakers and add-

on amplifiers sound distorted at the preferred sound level.

DEMO ON

DEMO OFF

San Jose MP41_body_en 8/28/01, 6:04 PM7

ENGLISH

E-8

Turn on/off message edit

You can edit the turn on/off message and store it in memory.

Following four messages can be edit with 12 characters each.

When you turn on the unit, “MESSAGE 1” will be displayed

then “MESSAGE 2” will momentarily displayed before actual

power on.

When you turn off the unit, “MESSAGE 3” will be displayed

then “MESSAGE 4” will momentarily displayed before actual

power off.

Turn-on message

• MESSAGE 1 / MESSAGE 2

Turn-off message

• MESSAGE 3 / MESSAGE 4

1. Repeatedly press the

DISP

to display the “MESSAGE ON”

on the display window.

2. Press the

MUTE / SENS

to flash the “MESSAGE 1”.

3. Rotate the dial to select the desired message you want

to edit.

MESSAGE 1 ➜ MESSAGE 2 ➜ MESSAGE 3 ➜ MES-

SAGE 4

4. Press the

MUTE / SENS

, then enter the character.

A. Rotate the dial in a clockwise direction to select the

desired characters.

(A~Z, a~z, 0~9, ( )

∗ + , − . / ! ” # $ % & ’ : ; < = > ?

@ [ \ ] ˆ _ ` { } ˜ )

B. Press the

TUN/TRK

to move the flashing cursor to

the next position. If you press

TUN/TRK

, the flashing

cursor moves to the left.

C. Repeat steps A. and B. to complete entering the en-

tire message 12 characters max.

Tips

•

To erase/correct a message, press the

DISP

for more

than 2 seconds to clear the character and re-enter.

•

When entering a name, pressing the following but-

tons affects the display of characters as follows:

: Changes to inputting letters. (Starts with “A”.)

If pressed while letters are already selected,

switches between upper and lower case letters.

: Changes to inputting numbers. (Starts with “0”.)

: Changes to inputting symbols. (Starts with “(”.)

: Enters a space (blank).

5. Press the

MUTE / SENS

to store the message.

The new message flashes.

6. To return to the normal radio reception, Press

DISP

Notes

• If you make no button input or dial operation in 20 sec-

onds, the message edit mode will turn off automatically.

• Make sure the “MESSAGE” will be “ON” .

Erasing the turn on/off message

You can erase the turn on/off message if so desired.

1. Repeatedly press the

DISP

to display the “MESSAGE ON”

on the display window.

2. Press the

MUTE / SENS

to flash the message you edit.

3. Rotate the dial to select the desired message you want

to erase.

4. Press the

DISP

for more than 2 seconds.

Repeat steps 1. and 3. if you want to erase other mes-

sage.

5. To return to the normal radio reception, Press

DISP

San Jose MP41_body_en 8/28/01, 6:04 PM8

ENGLISH

E-9

Radio Reception

Receiving the Memorized Stations

1. Press the

BND / TS

to select the desired AM or FM band.

2. Press the

momentarily.

Local/Distant (LO/DX) Selection

This feature is used to select the signal strength at which the

radio will stop during Seek Tuning.

Press the

MUTE / SENS

for more than 2 seconds to select the

Local setting and only strong (local) stations will be received.

The “lo” indicator appears on the display window.

Pressing for more than 2 seconds again will select the Dis-

tant setting and the radio will stop at a wider range of signals,

including weaker more distant stations. The “lo” indicator will

go out on the display window. DX is the suggested default

setting.

Preset Scan Tuning

1. Press the

BND / TS

to select the desired AM or FM band.

2. Hold the

SC/PS

pressed for more than 2 seconds.

“SCAN” indicator will appear on the display window.

The unit will scan preset memory for the 12 stations from

the AM/AMT band or the 18 stations from the FM1/FM2/

FMT bands. The unit will stop at each preset station for 8

seconds, before continuing to the next preset station.

Press the

SC/PS

again to stop Preset Scan Tuning and

remain this on the selected frequency.

Memorizing Stations Automatically (Travel Store)

1. Press the

BND / TS

to select the desired AM or FM band.

2. Hold the

BND / TS

pressed for longer than 2 seconds.

Up to 6 stations with strong signals will be automatically

stored in preset memory for the selected band.

If the radio is in FM1 or FM2, it switches to FMT. If the

radio is in AM, it switches to AMT.

Note

This function is available for FMT and AMT.

Memorizing Only the Desired Stations

You can store up to 6 stations on each band (18 for FM1, FM2

and FMT, 12 for AM and AMT) in the order of your choice.

1. Press the

BND / TS

to select the desired band.

2. Press the

TUN/TRK

to tune in stations.

3. Press and hold the desired preset memory button

for about 2 seconds until the frequency indicator

flashes twice.

The number of the pressed preset memory button ap-

pears on the display window.

Note

If when you store another station on the same preset number

button, the previously stored station is replaced with new one.

Seek Tuning

1. Press the

BND / TS

to select the desired AM or FM band.

FM1 ➜ FM2 ➜ FMT ➜ AM ➜ AMT

(FMT & AMT are Travel Store bands.)

2. Press the

TUN/TRK

to tune in stations. Tuning automati-

cally stops at a broadcasting frequency.

When tuned in to FM stereo broadcasting stations, the

“

” stereo signal indicator will appear on the display

window.

Manual Tuning

1. Press the

BND / TS

to select the desired AM or FM band.

2. Press the

TUN/TRK

for more than 0.5 second

to activate the manual tuning mode. Press again to tune in

to stations.

“MAN” will appear on the display window.

After 4 seconds of completing Manual Tuning, the tuning

control will revert to the Seek Tuning mode.

Scan Tuning

1. Press the

BND / TS

to select the desired AM or FM band.

2. Hold the

SC/PS

pressed for less than 2 seconds.

The unit will scan the selected band for stations.

“SCAN” indicator will appear on the display window. The

unit will stop at each station for 8 seconds, before con-

tinuing to the next station.

Press the

SC/PS

again to stop Scan Tuning and remain

this on the selected frequency.

Tip

While tuning, the pie-shaped signal-strength meter

on the display is lit differently depending on the strength

of the signal. While scanning bands, the pie-shaped sig-

nal-strength meter spins. While playing CD’s, this display

also spins.

San Jose MP41_body_en 8/28/01, 6:04 PM9

ENGLISH

E-10

Storing the station names

You can assign a name to each radio station and store it in

memory. As much as 30 station names can be stored com-

posed with 12 characters each.

Storing the station names

1. Tune in a station whose name you want to store.

2. Press the

DISP

for more than 2 seconds.

The “NAME EDIT” will light then the “_ _ _ _ _ _ _ _ _ _ _

_” on the display window. The first “ _ ” flashes.

3. Enter the characters.

A. Rotate the dial in a clockwise direction to select the

desired characters.

(A~Z, a~z, 0~9, ( )

∗ + , − . / ! ” # $ % & ’ : ; < = > ?

@ [ \ ] ˆ _ ` { } ˜ )

B. Press the

TUN/TRK

to move the flashing cursor to

the next position. If you press

TUN/TRK

, the flashing

cursor moves to the left.

C. Repeat steps A. and B. to complete entering the en-

tire name 12 characters max.

Tips

•

To erase/correct a name, press the

DISP

for more

than 2 seconds to clear the character and re-enter.

•

When entering a name, pressing the following but-

tons affects the display of characters as follows:

: Changes to inputting letters. (Starts with “A”.)

If pressed while letters are already selected,

switches between upper and lower case letters.

: Changes to inputting numbers. (Starts with “0”.)

: Changes to inputting symbols. (Starts with “(”.)

: Enters a space (blank).

4. Press the

MUTE / SENS

to store the station name.

The station name flashes.

5. To return to the normal radio reception, Press

DISP

Note

If you try to store more than 30 station names, “

✳✳

FULL

✳✳

”

will be displayed.

Erasing the station names

1. Tune in any station and press the

DISP

for more than 2

seconds.

2. Press the

MUTE / SENS

The station name or “ _ _ _ _ _ _ _ _ _ _ _ _ ” flashing.

3. Rotate the dial to select the name of the station that you

want to erase. To erase all the names of the stations, dis-

play “✳ALL DELETE✳”.

4. Press the

DISP

for more than 2 seconds.

Repeat steps 3. and 4. if you want to erase other names.

5. To return to the normal radio reception, Press

DISP

Direct Access to Memorized Stations via

Station call

You can search for the memorized AM & FM station names in

the memory.

1. Press the

DISP

to display the “STATION CALL” on the

display window.

2. Rotate the large dial to select the desired station name.

3. Press the

MUTE / SENS

to tune in the desired station.

San Jose MP41_body_en 8/28/01, 6:04 PM10

ENGLISH

E-11

Listening to a disc that is already loaded

Press the

to select the CD mode.

Playback begins automatically.

Pausing Playback

Press the

To resume playback, press the

again.

Stopping Playback

Press the

BND / TS

to select the radio reception (FM1,FM2,

FMT or AM, AMT).

Ejecting Discs

Press the to eject the disc located behind flip-down front

panel.

Notes

• The unit will turn on automatically when a CD is inserted if

the ignition switch is ‘‘ON’’.

• When the disc is ejected from the CD slot, remove it within

10 seconds; otherwise, the disc will be reloaded automati-

cally.

Track Search

Press the

TUN/TRK

during CD mode. Track numbers appear

in the display window.

: Playback starts from the beginning of the next track.

: Playback starts from the beginning of the current track.

Press again to play the previous track.

Cue / Review

Press and hold the

TUN/TRK

. Release when you have found

the desired point.

: To search forward.

: To search backward.

Scan Play

Press the

SC/PS

during CD mode.

The ‘‘SCAN 1’’ indicator appears in the display window. This

will play the first 10 seconds of all the tracks on the disc.

Press the

SC/PS

again to cancel this feature.

Repeat Play

Press the

5/RPT

during CD mode.

The ‘‘RPT 1’’ indicator appears in the display window and the

current track is played repeatedly.

Press the

5/RPT

again to cancel this feature.

Mix Play

Press the

4/MIX

during CD mode.

The ‘‘MIX 1’’ indicator appears in the display window.

All the tracks on the current disc are played in random order.

Press the

4/MIX

again to cancel this feature.

Note

If the Mix, Repeat or Scan buttons are pressed for 2 seconds

or longer while playing a music CD, the unit will enter the

respective mode2. These modes can be used for playing MP3

discs which contain a number of folders. (See page 14.)

Since a music CD is treated as a folder, there is almost no

difference in the operation.

CD Operations

Playing the CD player

Loading Discs

1. Press the

OPEN

and insert the disc.

2. Close the front panel. ‘‘LOADING’’ and ‘‘FILE CHECK’’ will

appear in the display window.

Playback begins automatically.

Note

Make sure that the front panel is closed when playback be-

gins.

Playback with the front panel open causes the

unit to turn off automatically in about 10 min-

utes.

! NEVER Insert a 3-inch CDs.

This unit is designed for playback of standard 5-inch CD’s

only. Do not attempt to use 3-inch CD singles in this unit,

either with or without an adaptor, as damage to the player

and/or disc may occur.

Tips

• When a CD is loaded, the

on the display remains lit.

• During playback of a CD, the pie-shaped signal-strength

meter

spins.

Labeled side up

San Jose MP41_body_en 8/28/01, 6:04 PM11

ENGLISH

E-12

CD Changer Controls

Storing the CDC disc names

You can label each disc with a personalized name. As many

as 99 disc names can be stored, composed with 7 characters

each.

Storing the CDC disc names

1. Play the CD and press the

DISP

for more than 2 sec-

onds. The “NAME EDIT” will light then the “_ _ _ _ _ _ _”

on the display window. The first “ _ ” flashes.

2. Enter the characters.

A. Rotate the dial in a clockwise direction to select the

desired characters.

( A~Z 0~9 ( )

∗ + , − . / )

B. Press the

TUN/TRK

to move the flashing cursor to

the next position. If you press

TUN/TRK

, the flashing

cursor moves to the left.

C. Repeat steps A. and B. to complete entering the en-

tire name 7 characters max.

Tips

•

To erase/correct a name, press the

DISP

for more than

2 seconds to clear the character and re-enter.

•

When entering a name, pressing the following but-

tons affects the display of characters as follows:

: Changes to inputting letters. (Starts with “A”.)

If pressed while letters are already selected,

switches between upper and lower case letters.

: Changes to inputting numbers. (Starts with “0”.)

: Changes to inputting symbols. (Starts with “(”.)

: Enters a space (blank).

3. Press the

MUTE / SENS

to store the disc name.

The disc name flashes.

4. To return to the normal CD playback mode, Press

DISP

Playing the CD Changer

This product can control a CD changer. Please check with

your nearest car stereo specialist for recommendations of the

models that will work with this radio (See page 1).

Press the

to switch the CD changer mode. Disc No,

Track No, and Track time appear on the display window and

playback begins automatically. Press again to change back to

built-in CD operation.

Disc Select

Press the Disc select buttons to select the desired disc for

play.

FOLDER +

: To advance to a higher number disc.

FOLDER –

: To return to a lower number disc.

Track Search

Press the

TUN/TRK

Track numbers appear in the display window.

: Playback starts from the beginning of the next track.

: Playback starts from the beginning of the current track.

Press again to play the previous track.

Cue / Review

Press and hold the

TUN/TRK

. Release when you have found

the desired point.

: To search forward.

: To search backward.

Track / Disc Scan Play

Track Scan

Press the

SC/PS

The “SCAN ON” indicator appears in the display window. This

will play the first 10 seconds of all the tracks on all the discs.

Press the

SC/PS

again to cancel this feature.

Disc Scan

Press the

SC/PS

for more than 2 seconds.

The ‘‘SCANDISC ON’’ indicator appears in the display win-

dow. This will play the first 10 seconds of the first track on

each disc. Press the

SC/PS

again to cancel this feature.

Track / Disc Repeat Play

Track Repeat

Press the

5/RPT

The ‘‘RPT ON’’ indicator appears in the display window and

the current track is played repeatedly.

Press the

5/RPT

again to cancel this feature.

Disc Repeat

Press the

5/RPT

for more than 2 seconds.

The ‘‘RPTDISC ON’’ indicator appears in the display window

and the current disc will be continually repeated.

Press the

5/RPT

again to cancel this feature.

Track / Disc Mix Play

Track Mix

Press the

4/MIX

The ‘‘MIX ON’’ indicator appears in the display window.

All the tracks on the current disc are played in random order.

Press the

4/MIX

again to cancel this feature.

Disc Mix

Press the

4/MIX

for more than 2 seconds.

The ‘‘MIXDISC ON’’ indicator appears in the display window.

Both discs and tracks will be played in random order.

Press the

4/MIX

again to cancel this feature.

Tip

During Disc scan, Disc Repeat or Disc Mix, the

will be lit

on the display.

San Jose MP41_body_en 8/28/01, 6:04 PM12

ENGLISH

E-13

Erasing the CDC disc names

1. Press the

DISP

for more than 2 seconds during CD

changer mode.

2. Press the

MUTE / SENS

The disc name or “ _ _ _ _ _ _ _ ” is now flashing.

3. Rotate the dial to select the name that you want to erase.

To erase all the names, display “ ✳ALL DELETE✳ ”.

4. Press the

DISP

for more than 2 seconds.

Repeat steps 3. and 4. if you want to erase other names.

5. To return to the normal CD playback mode, Press

DISP

Direct Access to Memorized Disc Names via

Disc call

You can search for the memorized disc names in the memory.

1. Press the

DISP

to display the “DISC CALL” on the display

window.

2. Rotate the large dial to select the desired disc name.

3. Press the

MUTE / SENS

to start playback for the desired sta-

tion.

IDC A09 Changer:

The IDC A09 is a 5-disc CD Changer. When using the Folder

+ & – keys, it is possible to mistakenly ask the IDC A09 for a

CD Disc higher than the number 5 (Five).

When this command is manually done in error, the San jose’s

Display will read disc numbers above 5, but the unit will then

only play but a few seconds of the next disc, which would be

Disc 1, whereas the Display is reading disc number 6 (Six)

which does not exist. Choosing a vacant / empty IDC A09

disc slot will result in a “No Magazine” or a double dashes

(– –) message in the LCD.

Do one of the following remedies:

Manually select the desired disc at the Changer’s controls,

Or allow the IDC A09 to automatically cycle to the next disk

after the completion of Disc #5,

Or Press Folder + or – until Disc 1 (One) or the desired disc is

displayed in the receivers LCD.

San Jose MP41_body_en 8/28/01, 6:04 PM13

ENGLISH

E-14

MP3 / WMA operation

You can play MP3 and WMA files written on CD-ROMs, CD-

Rs, or CD-RWs by following the procedures below.

In this section, “track” and “album” mean “MP3 or WMA file”

and “folder” in PC terminology, respectively.

MP3 / WMA play

Loading Discs

1. Press the

OPEN

and insert a CD-ROM, CD-R, or CD-RW

with the labeled side upward.

2. Close the front panel.

During scanning of the disc, ‘‘LOADING’’and ‘‘FILE CHECK’’

appear in the display window.

Playback begins automatically.

CD-R/RW with very complex folder trees could take in the

range of 20-seconds to load.

Listening to a disc that is already loaded

Press the

to select the CD mode.

Playback begins automatically.

Pausing Playback

Press the

To resume playback, press the

again.

Stopping Playback

Press the

BND / TS

to select the radio reception (FM 1, FM 2,

FT or AM, AT).

Ejecting Discs

Press the to eject the disc located behind the flip-down

front panel.

Notes

• The unit will turn on automatically when a CD is inserted if

the ignition switch is ‘‘ON’’.

• When the disc is ejected from the CD slot, remove it within 10

seconds; otherwise, the disc will be reloaded automatically.

• ID3 Tags are not supported for WMA files.

Track Search

Press the

TUN/TRK

during CD mode. Track numbers appear

in the display window.

: Playback starts from the beginning of the next track.

: Playback starts from the beginning of the current track.

Press again to play the previous track.

Album(Folder) Search

Press the

FOLDER +

FOLDER –

during CD mode. Folder indica-

tor “

” flashes in the display window.

FOLDER +

: Playback starts from the beginning of the next folder.

FOLDER –

: Playback starts from the beginning of the previous

folder.

Cue / Review

Press and hold the

TUN/TRK

. Release when you have found

the desired point.

: To search forward.

: To search backward.

Scan / Folder Scan Play

Scan Play (Mode1)

Press the

SC/PS

during CD mode.

The ‘‘SCAN 1 ON’’ appears in the display window. This will

play the first 10 seconds of all the tracks on the disc.

Press the

SC/PS

again to cancel this feature.

Folder Scan Play (Mode2)

Press the

SC/PS

for more than 2 seconds during CD mode.

The ‘‘SCAN 2 ON’’ appears in the display window. This will

play the first 10 seconds of first tracks in each folder.

Press the

SC/PS

again to cancel this feature.

Repeat / Folder Repeat Play

Repeat Play (Mode1)

Press the

5/RPT

during CD mode.

The ‘‘RPT 1 ON’’ appears in the display window and the cur-

rent track is played repeatedly.

Press the

5/RPT

again to cancel this feature.

Folder Repeat Play (Mode2)

Press the

5/RPT

for more than 2 seconds during CD mode.

The ‘‘RPT 2 ON’’ appears in the display window and the cur-

rent folder is played repeatedly.

Press the

5/RPT

again to cancel this feature.

Mix Play / Folder Mix

Mix Play (Mode1)

Press the

4/MIX

during CD mode.

The ‘‘MIX 1 ON’’ appears in the display window.

All the tracks on the current folder are played in random or-

der. Press the

4/MIX

again to cancel this feature.

Folder Mix Play (Mode2)

Press the

4/MIX

for more than 2 seconds during CD mode.

The ‘‘MIX 2 ON’’ appears in the display window.

All the tracks on the current disc are played in random order.

Press the

4/MIX

again to cancel this feature.

ID3 Tag Jump

When a file containing an ID3 Tag is played, pressing

3/JUMP

immediately switches the unit to ID3 Tag scroll display.

When the scroll display finishes, the original display is restored.

When pressed

3/JUMP

while scroll display has priority, the origi-

nal display is restored after displaying “TRACK/TIME” for five

seconds.

Tip

When playing a file that does not contain an ID3 Tag or when

playing a WMA file, pressing

3/JUMP

causes “NO NAME” to be

displayed.

San Jose MP41_body_en 8/28/01, 6:04 PM14

ENGLISH

E-15

This unit can play back files recorded in MP3 or WMA format

on CD-ROM, CD-R (recordable) or CD-RW (rewritable) discs.

There are some limitations on the files and media that can be

used, so before recording files on a disc please carefully read

the following information.

ISO9660 Format

The unit can play back data recorded in ISO9660 format.

ISO9660 is an international standard for representative CD-

ROM file formats determined by ISO (International Standard

Organization).

The media formats that can be used by the unit include Level

1, Level 2 and the extension format known as Joliet.

What are MP3 and WMA?

• An MP3 file stores audio data compressed using the “MPEG

1 / 2 audio layer-3” file format. We call files that have the

“.mp3” extension “MP3 files”. Likewise for WMA files. WMA

is an abbreviation for Windows Media Audio. WMA files have

the extension “.wma” and are compatible with MP3 files.

• The unit cannot read files that have a file extension differ-

ent from “.mp3” or “.wma”.

• The unit cannot read files without an extension even if the

files are MP3 or WMA files.

Furthermore even if a file has an “.mp3” or “.wma” exten-

sion, the unit cannot read the file if is not recorded with the

MP3 or WMA data format.

Playback Limitations

• The number of tracks and number of albums (folder) that

can be played back from a disc are as follows.

Tracks : About 250 depending on file contents.

Albums(folder) :

A maximum of 250 depending on the num-

ber of tracks.

The unit also recognizes up to eight album(folder) levels.

• The unit can playback MP3 files with compression bit rates

from 32kbps~320kbps. However for the best balance of file

space and sound quality we recommend 128kbps. When

files compressed at less than 128kbps are played back, the

sound may have breaks in it.

Sampling rates are supported as follows.

MPEG 1 48k 44.1k 32k

MPEG 2 24k 22.05k 16k

MPEG 2.5 12k 11.03k 8k

In the case of WMA files, play back is possible only for files

encoded with a compression bit rate of at least 64kbps and

a sampling rate of 44.1 kHz.

• Please note that the unit cannot play files encoded using

the WMA copyright protection function.

• When playing WMA files, song, album and artist tags can-

not be displayed.

• The unit allows the playback of CD-R and CD-RW discs

containing a mixture of music CD data (CD-DA), MP3 and

WMA files. However playback of both types of data is pos-

sible only for Mixed Mode CDs/CD Extra created using Disc

at Once Method. (See below.)

• The unit also supports files compressed using VBR (vari-

able bit rate).

• The unit does not always play back MP3 and WMA files in

the order in which they were recorded.

• When many folders are recorded on a disc, the time required

to fetch information from the disc becomes longer.

•

We recommend that multi-session discs be limited to 10 sessions.

The packet write method is not supported.

The following three methods are used to record data (files)

on a disc. As the unit does not support the “Packet Write”

method please be aware of this.

The unit supports discs recorded with the “Disc at Once” and

“Track at Once” methods.

Disc at Once Method

With this method, all the data to be written is prepared in ad-

vance and then recorded on the disc in one go. Additional

writing of data is not possible.

Track at Once Method

With this method, data is written in file (track) units. Addi-

tional writing of data is possible.

Packet Write Method

With this method, tracks are sub-divided into packets depend-

ing on availability of space on the disc. Additional writing of

data is possible.

Display Information Limitations

• The unit can display folder and file names, ID3 Tags of length

up to 64 characters including the extension. However, cer-

tain special symbols may not display correctly.

• During playback of MP3 and WMA files, there may be occa-

sions when the elapsed playback time is not correctly dis-

played.

Important Points

• Please take care not to append the extensions for MP3 and

WMA files onto files of any other type. When a disc contain-

ing such files is played, the files will be incorrectly recog-

nized and played back. This will result in extremely loud noise

that may damage the speakers.

• Depending on the state of the disc or recorder or writing

software used to write on the disc, there may be cases when

the disc cannot be correctly played back. In such cases

please refer to the user manual for the tools you are using.

• When using a Macintosh personal computer, the file exten-

sion will not be added, so please add the extension “.mp3”

to the end of the file name.

• This unit does not support WAVE files.

• This unit does not support m3u playlists.

• The unit does not support “Emphasis”. (See “Glossary” on

page 17.)

MP3 / WMA Overview

San Jose MP41_body_en 8/28/01, 6:04 PM15

ENGLISH

E-16

Note Concerning Bit Rate and Record Time

Please refer to the following general guide concerning the bit

rate used when encoding and the overall time of a file re-

corded on disc.

Before recording on a disc, please carefully read the soft-

ware instructions and ensure you use it correctly.

Note

When the sampling frequency used for encoding is 44.1kHz

For highest

320kbps About 4hr

sound quality

CD quality

192 kbps About 7hr

(High sound quality)

CD quality

160 kbps About 8hr

(Medium sound quality)

CD quality

128 kbps About 10hr

(Standard)

When Creating Discs

Files will not always be played back in the order in which they

were recorded. When you want to ensure that files will be

played back in the order they were recorded, please write

onto the disc paying attention to the points below.

• Use writing software that can write MP3/WMA files on the

disc in the order of the file (track) names. Please check with

the software developers concerning the behavior and op-

eration of the writing software.

• Prefix numbers to the names of folders (albums) and files

(tracks) to arrange them in order. Shown below is a good

example (2 or three digits correctly entered.) and a bad ex-

ample (if the number of digits is not the same for all names,

the names will not be ordered correctly.)

Example

01XXXX.mp3 1XXXX.mp3

02XXXX.mp3 10XXXX.mp3

03XXXX.mp3 11XXXX.mp3

04XXXX.mp3 2XXXX.mp3

About Recommended CD-R and CD-RW Media

With some CD-R and CD-RW media, data may not be prop-

erly written depending on their manufacturing quality. In this

case, data may not also be reproduced correctly. We recom-

mend the media manufactured by the following companies:

CD-R Media

TDK USA Corp., Taiyo Yuden (U.S.A.), Inc., Ricoh Corpora-

tion, Eastman Kodak Company, Maxell Corporation of

America, Mitsubishi Chemical Corporation, Fuji Photo Film

U.S.A., Inc., Mitsui Chemicals, Inc., Sony Corporation of

America, Philips Electronics North America Corporation,

Imation Corp.

CD-RW Media

TDK USA Corp., Ricoh Corporation, Mitsubishi Chemical

Corporation

Several types of CD-R and CD-RW media are available, such

as 2X and 1X-4X. Please read the instruction manuals of the

drive and the recording software you are using to select the

right media.

San Jose MP41_body_en 8/28/01, 6:04 PM16

ENGLISH

E-17

Glossary

Bit rate

The bit rate expresses the amount of information transferred

per second as a number of bits. The greater the quantity of

information, the higher the bit rate.

The unit is “bits/second”. “kbps” indicates “kilo (1,000) bits/

second”.

Emphasis

The software used for recording has an “emphasis” capabil-

ity, which when turned on writes emphasis attributes on to

the audio track. When the emphasis bit is set the sound has a

smooth characteristic. However, at the current time almost all

CD players lack support for this function. It is no problem to

play back an audio track recorded with emphasis on with a

player not supporting emphasis.

Extension

In Windows and DOS personal computers, several charac-

ters are placed at the end of each file name to indicate the

type of file.

The extension consists of a period followed by three alphanu-

meric characters. The extension differs depending on file type.

The extension for MP3 files is “.mp3”.

ID3 Tags

This is a data format that allows a file name, title and artist

name etc. to be added to MP3 files.

This unit supports SONG ALBUM and ARTIST for Versions

1.0/1.1/2.2 and 2.3.

ID3 Tags are not supported for WMA files.

Multi-Session

When data is written on a CD-R disc, the data written from

the time writing starts until the time writing finishes is regarded

as a bundle called a session. The Track at Once Method al-

lows data to be added to a single disc one track at a time,

with each recording of a track being a single session.

The term multisession refers to the method of recording the

data for two or more sessions on a single disc. We recom-

mend that this unit be used for up to 10 sessions.

Structure of Folder Hierarchy

To keep data within a computer organized, related files may

be put into a folder, but in addition to files, a folder may also

have other folders put into it. Folder B may be put into folder

A, and folder C may be put into folder B so as to create a

“hierarchical structure”. The number of hierarchical levels that

can be recognized differs depending on the computer operat-

ing system. ISO9660 specifies up to 8 levels.

VBR (Variable Bit Rate)

MP3 files are normally encoded with a fixed bit rate (eg

128kbps etc.), however VBR encoding during which the bit

rate is varied while encoding is also possible. That is to say,

during periods of violent variation of sound the bit rate is in-

creased and during soundless periods the bit rate is de-

creased. Encoding in this way allows file size to be curbed

while maintaining high sound quality. However, some players

do not support VBR, so caution is required when using VBR.

Types of CD

• Audio CD(CD-DA)

This is the format used for audio CDs that can be played on

ordinary audio CD players. It is also called CD-DA (Com-

pact Disc Digital Audio).

• ISO9660 Format CD-ROM

ISO9660 is a CD-ROM standard file system determined by

ISO (International Organization for Standardization). CD-

ROMs with this format can be played by Windows and

Macintosh operating systems and also by UNIX operating

systems.

• HFS Format CD-ROM

This is a CD-ROM conforming to the HFS (Hierarchical File

System) used by Macintosh Mac OS.

• Hybrid CD-ROM

This is a CD-ROM containing a mixture of ISO9660 format

files and HFS format files.

• Mixed Mode CD

This is a CD-ROM containing both data files and audio files

on the one disc.

Mixed Mode CD is a standard developed for personal com-

puter use so the audio files on the CD cannot be played

with CD players that do not support Mixed Mode CD.

• CD Extra (Enhanced CD)

This differs from Mixed Mode CD in that the audio files are

followed on the disc by data files. CD Extra was standard-

ized by Sony and Philips to allow the audio files to be played

with an audio CD player and the data files to be read by a

personal computer.

San Jose MP41_body_en 8/28/01, 6:04 PM17

ENGLISH

E-18

hold for

2 seconds

(Direct access mode) (select) (set)

Remote control

unit rear surface

Removing the battery insulation sheet

If an insulation sheet is attached to the remote control unit,

make sure to remove the insulation sheet before use. In this

case, the batteries will already be inside and can be used

immediately.

Inserting Batteries

1. Push A in the direction of the arrow while holding B and

pull out.

2. Confirm that the (+) (

) terminals are correctly aligned

and insert the lithium battery (CR2025).

3. Push in the battery case until a “click” can be heard.

Battery case

Operation

Operate while facing towards the sensor of the main unit.

* Press and hold

** Press and hold for 2 seconds

Switching the Source

The mode will switch each time the SRC button is pressed.

Direct Access

For direct access during radio mode or CDC mode, use the

following operations.

Radio

CDC or AUX

Precautions on battery use

Always use lithium batteries (CR2025).

Warning

Use the lithium batteries properly

(1) Never recharge, short circuit, disassemble, modify, heat

or place in fire. This may result in fire, generation of heat

or explosion.

(2) Place batteries out of reach of infants. If accidentally swal-

lowed, consult a physician immediately.

(3) Use tape to insulate whenever disposing or storing batter-

ies. Contact with metals or other batteries may result in

fire or explosion.

Caution

Properly align the battery (+) (

) terminals

• Improper handling of batteries may cause fluid leakage or

explosions and may result in damage to the device or in-

jury.

Align the battery (+) (

) terminals correctly.

• Do not leave the remote control unit in high temperature

such as from direct sunlight. It results in the deformation of

the case, leakage of battery acid, and so on.

• Do not expose remote to water, damage may result.

Insulation Sheet

➜

Lithium battery

(CR2025)

Radio mode

Seek tuning

Preset scan**

Seek tuning

Preset select

Band select

Travel store**

CD mode

Scan play

Track search

Cue/Review*

CDC mode

Scan play

Disc scan**

Disc up

Disc down

Track search

Cue/Review*

Aux

Volume up/down

MP3/WMA

mode

Scan play

Folder scan**

Folder up

Folder down

Track search

Cue/Review*

Handling the RC-823 Remote Control Unit

San Jose MP41_body_en 8/28/01, 6:04 PM18

ENGLISH

E-19

Installations

Supplied Mounting Hardware

Sleeve

Bushing, Locking Mounting Strap Release

Screw screw and Screw Keys

Precautions

• Be sure to detach the front panel before you start in-

stalling the unit.

• Choose the mounting location carefully so that the unit will

not interfere with the normal driving operations of the driver.

• Use only the supplied mounting hardware for a safe and

secure installation.

• When mounting the unit in a car, keep the unit as level as

possible. If the unit must be mounted at an angle, due to the

design of the vehicle, make sure that the unit does not tilt

upward by more than 30°.

• Turn-off Demo mode before use.

Mounting Example

Installation in the dashboard.

1. Install the sleeve in the dashboard.

2. Select and bend the appropriate tabs to hold the sleeve

firmly in place.

Mounting Strap Use

3. Attaching the Mounting Strap to the underside of the

dash board, using screw.

Attach the back of the unit to the Mounting Strap us-

ing the support stem bolt and hardware.

Bushing Use

3. As shown in the figure below, securely fasten the

screw, which has been inserted into the bushing to

the rear of the set.

Fire wall

The distance to the fire wall var-

ies due to the type of the car. Be

sure to secure the unit by prop-

erly inserting the bushing.

Caution

Insufficient fastening of the

screw may cause some CD’s to

skip.

If your car has no accessory position on the

ignition key switch (POWER SELECT switch)

The illumination on the front panel is factory-set to be turned

on even when the unit is not being played. However, this set-

ting may cause some car battery wear if your car has no ac-

cessory position on the ignition key switch. To avoid this battery

wear, set the POWER SELECT switch located on the bottom

of the unit to the B position, then press the RESET button.

The illumination is reset to stay off while the unit is not being

played.

Reset button

Press the reset button with the point of

a sharp object such as a ball-point pen.

POWER SELECT SWITCH

(Located on the bottom of the unit)

Change the position with a jeweler’s screwdriver, etc.

A : Your car has an accessory position on the ignition

switch.

B : Your car has no accessory position on the ignition

switch.

Be sure to

press the reset button after changing the

switch and connecting the lines.

Note

If set to the

position, demonstration mode will be elimi-

nated.

San Jose MP41_body_en 8/28/01, 6:04 PM19

La page charge ...

Blaupunkt San Jose MP41 Le manuel du propriétaire

Marque: Blaupunkt

Modèle: San Jose MP41

Catégorie: Récepteurs multimédia de voiture

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Blaupunkt San Jose MP41 Owner's manual

Blaupunkt San Jose MP41 Le manuel du propriétaire

Blaupunkt San Jose MP41 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents