Whirlpool GI1500XHW0 Le manuel du propriétaire

Marque: Whirlpool

Modèle: GI1500XHW0

Catégorie: Fabricants de glaçons

Taper: Le manuel du propriétaire

Ce manuel convient également à

GI1500XHW1

Appliances

ICE MAKER

tc_ £_,,'_

For questions about features, operation/performance,

parts, accessories or service, call: 1-800-253-1301.

In Canada, call for assistance 1-800-461-5681, for installation

and service, call: 1-800-807-6277 or visit our website at...

www.whirlpool.com or www.whirlpool.com/canada

LAMACHINEA

GLA(_ONS

Au Canada, pour assistance, composer le 1-800-461-5681, pour

installation ou service 1-800-807-6777 ou visitez notre site web

www.whirlpool.com/canada

Table of Contents/Table des matieres .............................. 2

2208357

TABLEOF

CONTENTS

ICE MAKER SAFETY ....................................................... 3

PARTS AND FEATURES .................................................. 4

INSTALLING YOUR ICE MAKER ....................................... 5

Unpacking the Ice Maker ................................................. 5

Space Requirements ....................................................... 5

Electrical Requirements ................................................... 6

Leveling the Ice Maker ..................................................... 6

Connecting the Ice Maker to a Water Source ................ 7

Reversing the Door Swing ............................................... 9

Understanding Sounds You May Hear ......................... 11

USING YOUR ICE MAKER ............................................... 11

Understanding How Your Ice Maker Works ................. 11

Setting the Controls ....................................................... 12

CARING FOR YOUR ICE MAKER ................................... 12

Cleaning Exterior Surfaces ............................................ 12

Cleaning the Ice Maker System .................................... 13

Cleaning the Condenser ................................................ 13

Cleaning the Interior Components ................................ 14

Vacation and Moving Care ............................................ 15

TROUBLESHOOTING ....................................................... 16

ASSISTANCE OR SERVICE ............................................. 17

WARRANTY ...................................................................... 18

TABLEDES

MATIERES

SECURITE DE LA MACHINE A GLA(;ONS ................... 19

PIECES ET CARACTERISTIQUES ................................. 20

INSTALLATION DE LA MACHINE A GLA(;ONS ............ 21

Deballage de la machine a glaqons .............................. 21

Espace requis ................................................................. 21

Specifications electriques ............................................. 22

Mise d'aplomb de la machine a glaqons ...................... 22

Raccordement de la machine

glaqons a I'alimentation en eau ................................ 23

Inversion du sens d'ouverture de la porte .................. 26

Comprehension des bruits

que vous pouvez entendre ............................................ 27

UTILISATION DE LA MACHINE A GLA(;ONS ................ 28

Comprehension du fonctionnement

de la machine a glaqons ............................................... 28

Reglage des commandes .............................................. 29

ENTRETIEN DE LA MACHINE A GLA(;ONS .................. 29

Nettoyage des surfaces exterieures ............................. 29

Nettoyage du systeme de la machine a glaqons ......... 30

Nettoyage du condenseur ............................................. 30

Nettoyage des composants interieurs ......................... 31

Precautions a prendre pour les

vacances ou le demenagement .................................... 32

DEPANNAGE ..................................................................... 33

ASSISTANCE OU SERVICE ............................................. 34

GARANTIE ......................................................................... 35

ICE MAKERSAFETY

Your safety and the safety of others is very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all

safety messages.

This is the safety alert symbol.

This symbol alerts you to hazards that can kill or hurt you and others.

All safety messages will be preceded by the safety alert symbol and the word "DANGER" or

"WARNING." These words mean:

You will be killed or seriously injured if you don't

follow instructions.

You can be killed or seriously injured if you don't

follow instructions.

All safety messages will identify the hazard, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

_VARNNNG: To reduce the risk of fire, electric shock, or injury when using your ice maker, follow these basic

precautions:

• Plug into a grounded 3 prong outlet.

• Do not remove ground prong.

• Do not use an adapter.

• Do not use an extension cord.

• Disconnect power before cleaning.

• Disconnect power before servicing.

• Replace all panels before operating.

• Use two or more people to move and install

ice maker.

SAVE THESE INSTRUCTIONS

PARTSANDFEATURES

CLEANING

1. Control Panel

2. Cutter Grid Cover

3. Water Pan

4. Model Serial Number Label (on left cabinet wall)

5. Ice Retainer Baffle

6. Lower Access Panel

7. Ice Level Sensor

8. Magnetic Door Catch

INSTALLINGYOUR

ICEMAKER

Excessive Weight Hazard

Use two or more people to move and install

ice maker.

Failure to do so can result in back or other injury.

Removing packaging materials

IMPORTANT: Do not remove any permanent instruction

labels inside your ice maker or the Tech Sheet that is

fastened behind the lower access panel.

• Remove tape and any labels from your ice maker

before using (except the model and serial number

label).

To remove any remaining tape or glue, rub the area

briskly with your thumb. Tape or glue residue can also

be easily removed by rubbing a small amount of liquid

dish soap over the adhesive with your fingers. Wipe

with warm water and dry.

Do not use sharp instruments, rubbing alcohol,

flammable fluids, or abrasive cleaners to remove tape

or glue. These products can damage the surface of

your ice maker.

Cleaning before use

After you remove all of the packaging materials, clean the

inside of your ice maker before using it. See the cleaning

instructions in the "Caring for Your Ice Maker" section.

To ensure proper ventilation for your ice maker, the

front side must be completely unobstructed. The unit

may be closed-in on the top and three sides, but the

installation should allow the ice maker to be pulled

forward for servicing if necessary.

Installation of the ice maker requires a cold water

supply inlet of V4"(6.35 mm) OD soft copper tubing with

a shut-off valve and either a gravity-drain system or

condensate pump to carry the water to an existing

drain.

Choose a well ventilated area with temperatures above

55°F (13°C) and below IO0°F (38°C). Best results are

obtained between 70°F (21°C) and 90°F (32°C). This

unit MUST be installed in an area protected from the

elements, such as wind, rain, water spray, or drip.

When installing the ice maker under a counter, follow

the recommended opening dimensions shown. Place

electrical and plumbing fixtures in the recommended

location as shown.

NOTE: Do not kink or pinch the power supply cord

between the ice maker and cabinet.

34"

(86.4 cm)

Min.

341/2,,

(87.6 cm)

Max.

24"

30.1 cm)

t 281/2.

(72.4 cm)

(38.1 cm)

1.Recommended Location for Electrical and

Plumbing Fixtures.

2. Floor Level

You should choose a location where the floor is even. It

is important for the ice maker to be level in order to

work properly. If needed, you can adjust the height of

the ice maker by changing the position of the rear

wheels. See the "Leveling the Ice Maker" section.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in

death, fire, or electrical shock.

Before you move your ice maker into its final location, it is

important to make sure you have the proper electrical

connection:

A 115 Volt, 60 Hz., AC only 15 ampere electrical supply,

properly grounded in accordance with the National

Electrical Code and local codes and ordinances, is

required.

It is recommended that a separate circuit, serving only

your ice maker, be provided. Use a receptacle which

cannot be turned off by a switch or pull chain.

Recommended grounding method

For your personal safety, this appliance must be grounded.

This appliance is equipped with a power supply cord

having a 3 prong grounding plug. To minimize possible

shock hazard, the cord must be plugged into a mating,

3 prong, grounding-type wall receptacle, grounded in

accordance with the National Electrical Code and local

codes and ordinances. If a mating wall receptacle is not

available, it is the personal responsibility of the customer

to have a properly grounded, 3 prong wall receptacle

installed by a qualified electrician.

It is important for the ice maker to be level in order to work

properly. Depending upon where you install the ice maker,

you may need to make several adjustments to level it.

Tools required

• Carpenter's level

• Adjustable wrench

• 1/4"socket wrench

Undercounter installation

If you are installing the ice maker under a countertop, then

you may need to adjust the height of the ice maker. The

adjustable rear wheels are preset to position 1for a

cabinet opening height of 34" (86.4 cm).

1.For cutout height of 34" (86.4 cm)

2. For cutout height of 34_" (86.7 cm)

3. For cutout height of 34_6" (87.2 cm)

4. For cutout height of 34½" (87.6 cm)

adjust the rear wheel height

Using a 1/4"socket wrench, remove the five screws from

the rear access panel and carefully pull the panel away

from the drain hose.

Using a %" or adjustable wrench, remove the screw

that holds the rear wheel.

NOTE: Pushing up against the top back of the ice

maker takes some of the weight off of the wheels. This

makes it easier to remove the screws.

Move the rear wheel and screw to a new position as

needed for your cabinet opening height. Tighten the

screw completely.

Repeat Steps 2 and 3 to change the position of the

wheel on the other side.

Replace the rear panel and screws. Be sure that the

drain tube is positioned in the opening provided.

Use the front leveling legs to make sure the product is

level.

To adjust the front leveling legs

Your ice maker has two adjustable leveling legs to help you

steady the product and make sure it is level.

SUGGESTION: It is easier to adjust the leveling legs if you

have another person to assist you.

1, Place a carpenter's level on top of the product to see if

the ice maker is level from front to back and side to

side.

Push up on the top front of the ice maker, and then

locate the leveling screws that are on the bottom front

of the product.

Using an adjustable wrench, change the height of the

legs as follows:

• Turn the leveling leg to the right to lower that side of

the ice maker.

• Turn the leveling leg to the left to raise that side of

the ice maker.

NOTE: The ice maker should not wobble. Use shims to

add stability when needed.

Use a carpenter's level to re-check the ice maker to see

that it is even from front to back and side to side. If the

ice maker is not level, repeat Steps 2 and 3. If the ice

maker is level, go to the "Connecting the Ice Maker to a

Water Source" section.

Freestanding installation

If you are not installing your ice maker under a countertop,

you will probably not need to adjust the rear wheel height,

Follow the steps outlined in "To adjust the front leveling

legs" earlier in this section,

NOTE: The ice maker should not wobble. Use shims to

add stability when needed.

Read all directions carefully before you begin.

IMPORTANT:

• All installations must be in accordance with local

plumbing codes requirements,

• Use copper tubing and check for leaks,

• Install copper tubing only in areas where temperatures

will remain above freezing,

Tools required:

• Standard screwdriver

• 7A6"and 1/2"open-end wrenches or two adjustable

wrenches

• 1/4" nut driver

• 1/4"drill bit

• Hand drill or electric drill properly grounded

NOTE: Your ice maker dealer has a kit available with a 1/4"

(.635 cm) saddle-type shut-off valve, a union, and copper

tubing. Before purchasing, make sure a saddle-type valve

complies with your local plumbing codes. Do not use a

piercing-type or ¾6" (.476 cm) saddle valve which reduces

water flow and clogs more easily.

Connecting the water line:

1. Turn off main water supply. Turn on nearest faucet long

enough to clear line of water.

Find a 1/2"(1.27 cm) to 11/4"(3.18 cm) vertical cold

water pipe near the ice maker.

NOTE: Horizontal pipe will work, but the following

procedure must be followed: Drill on the top side of the

pipe, not the bottom. This will help keep water away

from the drill. This also keeps normal sediment from

collecting in the valve.

Using a grounded drill, drill a 1/4"(.635 cm) hole in the

cold water pipe you have selected.

Fasten shut-off valve to cold water pipe with pipe

clamp. Be sure outlet end is solidly in the 1/4"(.635 cm)

drilled hole in the water pipe and that washer is under

the pipe clamp. Tighten packing nut. Tighten the pipe

clamp screws carefully and evenly so washer makes a

watertight seal. Do not overtighten the pipe clamp or

you may crush cold water pipe if it is soft copper

tubing. Do not use a piercing-type or ¾6" (.476 cm)

saddle-type valve which reduces water flow and clogs

more easily.

5. REAR VIEW

Now you are ready to connect the copper tubing. Use

1/4"(.635 cm) OD soft copper tubing for the cold water

supply.

Measure from the connection at the front of the ice

maker to the cold water pipe. Add 3 feet to ensure

that you have the proper length. This is the length of

1/4"(.635 cm) OD soft copper tubing you need for

the job. Be sure both ends of the copper tubing are

cut square.

Slip compression sleeve and compression nut on

copper tubing as shown. Insert end of tubing into

outlet end squarely as far as it will go. Screw

compression nut onto outlet end with adjustable

wrench. Do not overtighten.

6 5 4

1. Cold Water Pipe

2. Pipe Clamp

3. Copper Tubing

4. Compression Nut

5. Compression Sleeve

6. Shut-Off Valve

7. Packing Nut

Place the free end of the tubing into a container or sink,

and turn on main water supply and flush out tubing

until water is clear. Turn off shut-off valve on the water

pipe.

NOTE: Always drain the water line before making the

final connection to the inlet of the water valve to

prevent possible water valve malfunction.

Remove the two screws in the lower access panel and

the two screws in the base grille area of the front panel

support. Pull forward to remove the lower access

panel.

Position the tubing so it can enter one of the two

access holes located at the right-hand rear of the

cabinet as shown. The tubing should extend beyond

the cabinet front when the cabinet is pushed back into

position. Move the ice maker into position.

II I

1. Upper Water Line Access Hole

2. Lower Water Line Access Hole

9, Bend the copper tubing to meet the water valve inlet on

the water valve which is located in the front of the ice

maker cabinet as shown.

10.

Unscrew the water valve inlet cover, and attach the

copper tubing with the compression sleeve and nut.

NOTE: To prevent rattling, be sure the copper tubing

does not touch the cabinet's side wall or other parts

inside the cabinet.

FRONT VIEW

511/16"

(14.5crn)

1. Water Pan Drain

2. Water Valve

11,

Turn shut-off valve on. Check for leaks. Tighten any

connections (including connections at the valve) or

nuts that leak. The ice maker is equipped with a built-in

water strainer. If local water conditions require periodic

cleaning or a well is your source of water supply, a

second water strainer should be installed. Obtain a

water strainer from your nearest appliance dealer and

install it at either tube connection.

12, Replace the lower access panel and screws.

Connecting the drain

Gravity drain system

Connect the drain pump hose (provided with the product)

to your drain in accordance with all state and local codes

and ordinances. If the ice maker is provided with a gravity

drain system, follow these guidelines when installing drain

lines: (This will prevent water from flowing back into the ice

maker storage bin and potentially flowing onto the floor

causing water damage.)

• Drain lines must have a minimum of%" (1.6 cm) inside

diameter.

Drain lines must have a 1" drop per 48" [(2.54 cm) drop

per 122 cm)] of run or 1/4"drop per 12" [(.635 cm) per

30.5 cm)] and must not have low points where water

can settle.

The floor drains must be large enough to

accommodate drainage from all drains.

The ideal installation has a standpipe with a 11/2"(3.81

cm) to 2" (5.08 cm) PVC drain reducer installed directly

below the outlet of the drain tube as shown. You must

maintain a 1" (2.54 cm) air gap between the drain pump

hose and the standpipe.

It may be desirable to insulate the drain line thoroughly

up to the drain inlet.

After ensuring that the drain system is adequate, follow

these steps to properly place the ice maker:

1, Plug in ice maker or reconnect power.

2, Re-check the ice maker to be sure that it is level. See

the "Leveling the Ice Maker" section.

3. Push the ice maker into position so that the ice maker

drain tube is positioned over the PVC drain reducer.

SIDE VIEW

l,.u

3 5/811

(9,2 cm)

23"

(58,4cm)

2" - 1 1/2"

(5cm - 3,8 cm)

1. Drain Hose

2. 1" (2.54 cm) Air Gap

3. PVC Drain Reducer

4. Center of drain should be 23" (58.4 cm)

from front of door (with or without the ¾"

(1.91 cm) panel on the door).

If it is required by your local sanitation code, seal the

cabinet to the floor with an approved caulking

compound after all water and electrical connections

have been made,

Drain pump system (on some models)

Connect the drain pump hose (provided with the product)

to your drain in accordance with all state and local codes

and ordinances.

<t.I I,R,

TOOLS NEEDED: sad' wrench, 1/4"wrench, flat putty knife,

Phillips screwdriver

Hinge Pin

5A6-inchHex Head HingeScrew

Handle Screw

Endcap Screw

To remove door from hinges:

Electrical Shock Hazard

Disconnect power before servicing.

Replace all panels before operating.

Failure to do so can result in death or

electrical shock.

1, Unplug ice maker or disconnect power.

2, Remove the handle screws and handle (on some

models). Keep the parts together and set them aside.

Remove the two hex head screws from the upper

access panel. Lift up on the bottom of the access panel

to release it from the front of the ice maker. Do not

disconnect the wires.

With the upper access panel raised, remove the hinge

pin from the top hinge.

Remove the door from the hinges and screw the top

hinge pin back into the top hinge.

Replace the upper access panel loosely on the ice

maker.

Reverse the door endcaps as follows:

• Remove both the screws and endcaps (top and

bottom).

• Place the top endcap on the bottom of the opposite

side of the door with the long flat side facing the

door front.

• Place the bottom endcap on the top of the opposite

side of the door with the long flat side facing the

door front.

8. Set the door aside.

To reverse the hinges:

1, Unscrew and remove the top hinge. Replace the

screws in the empty hinge holes.

Remove the screws from the bottom of the opposite

side of the ice maker cabinet. Turn the top hinge upside

down so that the hinge pin points up. Place the hinge

on the bottom opposite side of the ice maker and

tighten screws.

Remove the plastic hinge pin sleeve from the "old"

bottom hinge and replace it on the new bottom hinge

pin.

4, Remove the "old" bottom hinge screws and hinge.

Replace the screws in the empty hinge holes.

5, Remove the screws from the top of the opposite side of

the ice maker cabinet. Turn the hinge upside down so

that the hinge pin points down.

6, Raise the upper access panel and place the hinge on

the top opposite side of the ice maker. Tighten the

hinge screws.

7. Remove the top hinge pin

replace door on hinges:

Place plastic hinge pin sleeve in the top hinge hole on

the door. Align the door with the top hinge hole and

replace the top hinge pin.

Replace the upper access panel and secure it with the

hex head screws.

3, Replace the handle and handle screws.

Top Hinge

1.Hinge Pin

2. Hinge Pin Sleeve

3. Hinge

4. Hex Head Hinge Screw

Bottom Hinge

1.Hex Head Hinge Screw

2. Hinge Pin Sleeve

3. Hinge

4. Hinge Pin

reverse the door catch:

Remove the hole plugs from the opposite side of the

door and set aside.

Remove the screws from the magnetic door catch and

replace it on the opposite side of the door.

Push the hole plugs into place on the opposite side of

the door.

4. Plug in ice maker or reconnect power,

Your new ice maker may make sounds that are not familiar

to you. Because the sounds are new to you, you might be

concerned about them. Most of the new sounds are

normal. Hard surfaces like the floor, walls and cabinets can

make the sounds seem louder than they actually are. The

following describes the kinds of sounds that might be new

to you and what may be making them.

• You will hear a buzzing sound when the water valve

opens to fill the water reservoir for each cycle.

• Rattling noises may come from the flow of the

refrigerant or the water line. Items stored on top of the

ice maker can also make noises.

The high efficiency compressor may make a pulsating

or high pitched sound.

Water running over the evaporator plate may make a

splashing sound.

Water running from the evaporator plate to the water

reservoir may make a splashing sound.

As each cycle ends, you may hear a gurgling sound

due to the refrigerant flowing in your ice maker.

You may hear air being forced over the condenser by

the condenser fan.

During the harvest cycle, you may hear a "thud" when

the ice sheet slides from the evaporator onto the cutter

grid.

When you first start the ice maker, you may hear water

running continuously. The ice maker is programmed to

run a rinse cycle before it begins to make ice.

USINGYOUR

ICEMAKER

When you first start your ice maker, the water pan will fill

and the system will rinse itself before starting to make ice.

The rinsing process takes about five minutes.

Under normal operating conditions, the ice maker will

cycle at preset temperatures. The ice level sensor located

in the ice storage bin will monitor the ice levels.

IMPORTANT

• If the water supply to the ice maker is turned off, be

sure to set the ice maker control to OFE

The ice maker is designed to make clear ice from the

majority of water sources on a daily basis. If your

results are unsatisfactory, your water may need to be

filtered or treated.

Making Ice

Water is constantly circulated over a freezing plate. As

the water freezes into ice, the minerals in the water are

rejected. This produces a clear sheet of ice with a low

mineral content.

When the desired thickness is reached, the ice sheet is

released and slides onto a cutter grid. The grid divides

the sheet into individual cubes.

The water containing the rejected minerals is drained

after each freezing cycle.

Fresh water enters the machine for the next ice making

cycle.

Cubes fall into the storage bin. When the bin is full, the

ice maker shuts off automatically and restarts when

more ice is needed. The ice bin is not refrigerated and

some melting will occur. The amount of melting varies

with room temperature.

NOTE: As the room and water temperatures vary, so

will the amount of ice produced and stored. This means

that higher operating temperatures result in reduced ice

production.

,,j)l _,,jl.+Ll, l. ,_,!,=.=,_It,l, ,%

I,,3

To start the normal ice making cycle, select ON.

To stop ice maker operation, select OFE

CARINGFORYOUR

ICE MAKER

Periodically inspect and clean the ice maker to keep it

operating at peak efficiency and to prevent premature

failure of system components.

Both the ice making system and the air cooled condenser

need to be cleaned regularly.

The minerals rejected from the circulating water during the

freezing cycle will eventually form a hard scaly deposit in

the water system which prevents a rapid release of the ice

from the freezing plate.

Clean the ice and water system periodically to remove

mineral scale buildup. Frequency of cleaning depends on

water hardness. With hard water (15 to 20 grains/gal. [4 to

5 grains/liter]), cleaning may be required as frequently as

every 6 months.

÷ ®

Wash the exterior enamel surfaces and gaskets with warm

water and mild soap or detergent. Wipe and dry. Regular

use of a good household appliance cleaner and wax will

help protect the finish. Do not use abrasive cleaners on

enamel surfaces as they may scratch the finish.

For products with a stainless steel exterior, use a clean

sponge or soft cloth and a mild detergent in warm water.

Do not use abrasive or harsh cleaners.

CLEANING

NOTE: The CLEAN setting is used whenever solutions are

circulated through the ice maker for cleaning. Only the

water pump and compressor operate at this setting. See

the "Cleaning the Ice Maker System" section.

NOTE: Use one 16 oz. (473 mL) bottle of NU-CALGON*

Nickel Safe Ice Machine Cleaner. To order, call 1-800-

442-9991 and ask for Part Number 8171307.

1, Push the selector switch to OFE

Wait 5 to 10 minutes for the ice to fall into the storage

bin. Remove all ice from the storage bin.

Unscrew the drain cap from the bottom of the water

pan located inside the storage bin as shown. Allow the

water to drain completely.

Replace the drain cap.

Read and follow all handling information on the cleaner

bottle before completing the steps below. Use one 16

oz. (473 mL) bottle of NU-CALGON* Nickel Safe Ice

Machine Cleaner.

6, Pour one bottle of solution into the water pan. Fill the

bottle twice with tap water and pour it into the water

pan.

Push the selector switch to CLEAN. (See the "Setting

the Controls" section.) The light will turn on, indicating

that the cleaning cycle is in process. When the

indicator light turns off (approximately 45 minutes), the

cleaning cycle is complete. During the cleaning cycle,

the system will both clean and rinse itself.

After the cleaning cycle is complete, remove the drain

cap from the water pan to see if any cleaning solution is

left in the water pan. If cleaning solution drains from the

water pan, you should run the clean cycle again.

NOTE: Severe scale buildup may require repeated

cleaning with a fresh quantity of cleaning solution.

9, Push the selector switch to ON to resume ice

production.

*NU-CALGON is a trademark of Calgon Corporation.

Electrical Shock Hazard

Disconnect power before cleaning.

Replace all panels before operating.

Failure to do so can result in death or

electrical shock.

A dirty or clogged condenser:

• Prevents proper airflow.

• Reduces ice making capacity.

• Causes higher than recommended operating

temperatures which may lead to component failure.

1. Unplug ice maker or disconnect power.

2. Remove the two screws in the lower access panel and

the two screws from the base grille area of the front

panel support. Pull forward to remove the lower access

panel.

3. Pull the bottom forward and then pull down to remove

the lower access panel.

, Remove dirt and lint from the condenser fins and the

unit compartment with a brush attachment on a

vacuum cleaner.

Remove the right-hand screw and loosen the left-hand

screw. Lift the cutter grid up and out and over the left-

hand screw.

NOTE: Make sure the plastic spacer from the right-

hand side of the cutter grid bracket stays with the

cutter grid.

5, Replace the lower access panel using the four screws.

6, Plug in ice maker or reconnect power.

Unplug ice maker or disconnect power.

Open the storage bin door and remove any ice that is in

the bin.

Remove the drain cap from the water pan and drain

thoroughly. Replace the drain cap.

Remove the three screws that hold the cutter grid

cover in place.

Unplug the wiring harness from the left side of the

cutter grid.

£:J

1 ..............

;S_

2 _ ........

1. Cutter Grid Cover

2. Screws

Unplug the ice level sensor from the right side of the

cutter grid. Pull the ice level sensor down and forward

away from the cutter grid.

10.

11,

12,

1. Cutter Grid Harness

2. Screw

3. Cutter Grid

4. Ice Level Sensor Harness

5. Plastic Spacer

6. Screw

Remove the two screws that hold the water pan in

place. Push down with one hand on the front of the pan

while pulling forward on the bottom back side.

Wash the interior components (cutter grid, exterior of

hoses, and water pan) and the storage bin, door

gasket, and ice scoop with mild soap or detergent and

warm water. Rinse in clean water. Then clean the same

parts with a solution of 1 tablespoon (15 mL) of

household bleach in 1 gallon (3.8 L) warm water. Rinse

again thoroughly in clean water.

NOTE: Do not remove hoses. Do not wash plastic parts

in dishwasher. They cannot withstand temperatures

above 145°F (63°C).

Replace water pan by pushing back on the bottom with

one hand while pushing up and back on the top.

Secure the water pan by replacing both screws.

Check the following:

• Drain cap from the water pan is in place.

• Hose from water pan is inserted into storage bin

drain opening.

Slide the cutter grid back into place and secure it by

replacing the right-hand screw and plastic spacer. Then

tighten the left-hand screw. Reconnect the cutter grid

and ice level sensor harnesses.

13. Plug in ice maker or reconnect power.

Electrical Shock Hazard

Disconnect power before servicing.

Replace all panels before operating.

Failure to do so can result in death or

electrical shock.

To shut down the ice maker:

1. Unplug ice maker or disconnect power.

2. Remove all ice from storage bin.

3. Shut off the water supply.

4. Remove the two screws in the lower access panel and

the two screws from the base grille area of the front

panel support. Pull forward to remove the lower access

panel.

5. Disconnect the inlet and outlet lines to water valve.

Allow these lines to drain and then reconnect to the

valve.

6. Replace lower access panel and screws.

7. Drain water from water pan by removing the drain cap.

8. If the room temperature will drop below 32° F (0° C),

remove water from the drain line.

For ice makers with a drain pump installed:

a) Plug in ice maker or reconnect power.

b) Turn ice maker off and remove all remaining ice from

ice bin.

c) Pour 1 quart (0.95 L) of water into the ice bin near

the drain and let the unit stand for approximately

five minutes. This will allow the water in the bin to

drain into the drain pump so that the pump will

remove the remaining water from the ice bin and the

drain pump.

d) Unplug ice maker or disconnect power.

Before using again, clean the ice maker and storage

bin.

10. Plug in ice maker or reconnect power.

NOTE: All components of the ice maker are permanently

lubricated at the factory. They should not require any

additional oiling throughout the normal life of the machine.

TROUBLE-

SHOOTING

Try the solutions suggested here first in order to

avoid the cost of an unnecessary service call.

Unit does not run

• Is the control set to ON?

Be sure that the control is set to ON.

Is the power cord plugged in?

Firmly plug the cord into a live outlet with proper

voltage.

Has a household fuse or circuit breaker tripped?

Replace the fuse or reset the circuit.

Is the room temperature cooler than normal?

Room temperature must be above 55°F (13°C).

Otherwise, bin thermostat may sense cold room

temperature and shut off even though bin is not full of

ice. Also, unit may not restart once it does shut off.

Unit runs but produces no ice

Is the control set to ON?

Be sure that the control is set to ON.

Is the water supply connected?

Make sure the water supply is properly connected and

turned on.

Unit runs but produces very little ice

Is the room temperature hotter than normal?

Room temperatures of more than 90°F (32°C) will

normally reduce ice production.

Is the condenser dirty?

Dirt or lint may be blocking the airflow through the

condenser. See the "Cleaning the Condenser" section.

Is there scale buildup in the ice maker?

If there is white scale buildup in the ice maker's water

or freezing system, you should clean the ice maker. See

the "Cleaning the Ice Maker System" and the "Cleaning

the Interior Components" sections.

Grid is not cutting ice sheets

Is the cutter grid securely in place?

Unplug the ice maker or disconnect power. Remove

the cutter grid cover and check the cutter grid harness

plug to make sure the connection is secure.

Taste in ice cubes

Is there unusually high mineral content in the water

supply?

The water may need to be filtered or treated.

Are there food items stored in the ice bin?

Do not store any foods in the ice bin.

Were all the packaging materials removed?

Make sure that all packaging materials were removed

at the time of installation.

ASSISTANCE

OR SERVICE

Before calling for assistance or service, please check

"Troubleshooting." It may save you the cost of a service

call. If you still need help, follow the instructions below.

When calling, please know the purchase date and the

complete model and serial number of your appliance. This

information will help us to better respond to your request.

If you need replacement parts

If you need to order replacement parts, we recommend

that you only use FSP° replacement parts. FSP

replacement parts will fit right and work right because they

are made with the same precision used to build every new

WHIRLPOOL ®appliance.

To locate FSP_replacement parts in your area, call our

Consumer Assistance Center telephone number or your

nearest designated service center.

Call the Whirlpool Consumer Assistance Center

toll free: 1-800-253-1301.

Our consultants provide assistance with:

• Features and specifications on our full line of

appliances,

• Installation information,

Use and maintenance procedures.

Accessory and repair parts sales.

Specialized customer assistance (Spanish speaking,

hearing impaired, limited vision, etc.).

Referrals to local dealers, repair parts distributors, and

service companies. Whirlpool designated service

technicians are trained to fulfill the product warranty

and provide after-warranty service, anywhere in the

United States.

To locate the Whirlpool designated service company in

your area, you can also look in your telephone directory

Yellow Pages.

Call the Inglis Limited Consumer Assistance Center toll

free: 1-800-461-5681 8:30 a.m. - 6:00 p.m. (EST)

Our consultants provide assistance with:

• Features and specifications on our full line of

appliances,

• Referrals to local dealers.

For service in Canada

Call 1-800-807-6777. Inglis Limited designated service

technicians are trained to fulfill the product warranty and

provide after-warranty service, anywhere in Canada.

For further assistance

If you need further assistance, you can write to Inglis

Limited with any questions or concerns at:

Consumer Relations Center

Inglis Limited

1901 Minnesota Court

Mississauga, Ontario L5N 3A7

Please include a daytime phone number in your

correspondence.

For further assistance

If you need further assistance, you can write to Whirlpool

with any questions or concerns at:

Whirlpool Brand Home Appliances

Consumer Assistance Center

c/o Correspondence Dept.

2000 North M-63

Benton Harbor, MI 49022-2692

Please include a daytime phone number in your

correspondence.

WHIRLPOOL ®ICE MAKER WARRANTY

ONE-YEAR FULL WARRANTY

For one year from the date of purchase when this product is operated in a residential or light commercial setting, and is maintainted

according to the instructions furnished with the product, Whirlpool will pay for FSP_replacement parts and repair labor to correct

defects in materials or workmanship. Service must be provided by a Whirlpool designated service company.

FIVE-YEAR FULL WARRANTY

In the second through fifth years from the date of purchase when this product is operated in a residential or light commercial setting,

and is maintained according to the instructions furnished with the product, Whirlpool will pay for FSP_replacement parts and repair

labor costs to correct defects in materials or workmanship in the compressor. Service must be performed by a Whirlpool designated

service company.

Whirlpool will not pay for:

1. Service calls to correct the installation of your ice maker, to instruct you how to use your ice maker, to replace house fuses or correct

house wiring or plumbing, to replace light bulbs.

2. Repairs when your ice maker is used in locations where usage exceeds ice making capabilities of unit (about 50 pounds in 24

hours). This ice maker is intended only for residential and/or light commercial use that does not exceed these capabilities.

3. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, or installation not in

accordance with local electrical or plumbing codes, or use of product not approved by Whirlpool.

4. Pickup and delivery. This product is designed to be repaired in the home.

5. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.

6. Replacement parts or repair labor costs for units operated outside the United Sates or Canada.

WHIRLPOOL CORPORATION AND INGLIS LIMITED SHALL NOT BE LIABLE FOR INCIDENTAL OR

CONSEQUENTIAL DAMAGES.

Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages, so this exclusion or

limitation may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state

to state or province to province.

Outside the United States and Canada a different warranty may apply. For details, please contact your authorized Whirlpool dealer.

If you need service, first see the "Troubleshooting" section of this book. After checking "Troubleshooting," additional help can be found

by checking the "Assistance or Service" section or calling our Consumer Assistance Center, toll free, 1-800-253-1301, from anywhere in

the U.S.A. For service in Canada, call 1-800-807-6777.

3/99

Keep this book and your sales slip together for future

reference. You must provide proof of purchase or

installation date for in-warranty service.

Write down the following information about your ice maker to

better help you obtain assistance or service if you ever need it.

You will need to know your complete model number and serial

number. You can find this information on the model and serial

number label, located on your appliance as shown in the "Parts

and Features" section of this book.

Dealer name

Address

Phone number

Model number

Serial number

Purchase date

ST CURITI DE LAMACHINE GLA( ONS

Votre s6curit6 et celle des autres est tr6s importante.

Nous donnons de nombreux messages de s6curit6 importants dans ce manuel et sur votre appareil menager.

Assurez-vous de toujours lire tousles messages de s6curit6 et de vous y conformer.

Voici le symbole d'alerte de s6curit6.

Ce symbole d'alerte de s6curit6 vous signale les dangers susceptibles de causer le d6cCs et

des blessures graves a vous et a d'autres.

Tous les messages de s6curit6 seront pr6c6d6s du symbole d'alerte de s6curit6 et du mot

"DANGER" ou "AVERTISSEMENT". Ces mots signifient :

Risque certain de d6c_s ou de blessure grave si

vous ne suivez pas les instructions.

Risque possible de d6c6s ou de blessure grave

si vous ne suivez pas les instructions.

Tousles messages de s6curit6 identiflent le danger et vous disent comment r6duire le risque de blessure et ce

qui peut se produire en cas de non-respect des instructions.

IMPORTANTES INSTRUCTIONS DE SI_CURITE

AVE RTISSEM ENT : Pour reduire le risque d'incendie, de choc electrique ou de blessures Iors de I'utilisation

de la machine a glaqons, il convient d'observer certaines precautions elementaires :

• Brancher sur une prise a 3 alveoles reliee a la terre. •

• Ne pas enlever la broche de liaison a la terre.

• Ne pas utiliser un adaptateur. •

• Ne pas utiliser un cable de rallonge.

• Utiliser deux ou plus de personnes pour deplacer •

et installer la machine a glaqons.

Deconnecter la source de courant electrique avant

le nettoyage.

Deconnecter la source de courant electrique avant

I'entretien.

Replacer tousles panneaux avant de faire la remise

en marche.

CONSERVEZ CES INSTRUCTIONS

PIECES ET CARACTI RISTIQUES

CLEANING

1. Tableau de commande

2. Couvercle de la grille de coupe

3. Bac d'eau

4. Plaque signaletique (sur la paroi gauche de la caisse)

5. Panneau de retenue des glaqons

6. Panneau d'acces inferieur

7. Detecteur de niveau de glace

8. Loquet de porte magnetique

La page charge ...

Whirlpool GI1500XHW0 Le manuel du propriétaire

Marque: Whirlpool

Modèle: GI1500XHW0

Catégorie: Fabricants de glaçons

Taper: Le manuel du propriétaire

Ce manuel convient également à

GI1500XHW1

Télécharger le PDF

rapport

dans d''autres langues

English: Whirlpool GI1500XHW0 Owner's manual

Whirlpool GI1500XHW0 Le manuel du propriétaire

Ce manuel convient également à

Whirlpool GI1500XHW0 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents