Powerfist 8667834 Le manuel du propriétaire
- Taper
- Le manuel du propriétaire
V4.0 8667834
Please read and understand all instructions before use. Retain this manual for
future reference.
User Manual
10 Ton Hydraulic Porta-Power
Autobody and Frame Repair Kit
8667834 10 Ton Hydraulic Porta-Power Autobody and Frame Repair Kit V4.0
2 For technical questions call 1-800-665-8685
SPECIFICATIONS
Capacity Hydraulic Ram 10 Ton (20,000 lb)
Duckbill Spreader 0.5 Ton (1,000 lb)
Body Toe/Ram Toe 0.8 Ton (1,600 lb)
Max. Continuous Pressure 8,900 PSI
Ram Stroke
5 in. (130 mm)
Duckbill spreader Range 3-1/4 in. (83 mm)
INTRODUCTION
The 10 Ton Hydraulic Porta-Power Autobody and Frame Repair Kit is essential for
auto body and frame repair. The kit straightens, bends or separates metal to repair
collision damage in half the time of conventional pounding methods.
The pump features a 5 in. stroke with a 13-5/8 to 18-3/4 in. extension range.
Extension tubes with snap-lock design allow for quick and easy assembly. An
automatic pump overload system helps prevent damage to the ram and accessories.
SAFETY
WARNING! Read and understand all instructions before using this tool. The
operator must follow basic precautions to reduce the risk of personal injury
and/or damage to the equipment.
Keep this manual for safety warnings, precautions, operating or inspection and
maintenance instructions.
HAZARD DEFINITIONS
Please familiarize yourself with the hazard notices found in this manual. A notice
is an alert that there is a possibility of property damage, injury or death if certain
instructions are not followed.
10 Ton Hydraulic Porta-Power
Autobody and Frame Repair Kit
V4.0 10 Ton Hydraulic Porta-Power Autobody and Frame Repair Kit 8667834
Visit www.princessauto.com for more information 3
DANGER! This notice indicates an immediate and specific hazard that will
result in severe personal injury or death if the proper precautions
are not taken.
WARNING! This notice indicates a specific hazard or unsafe practice that
could result in severe personal injury or death if the proper
precautions are not taken.
CAUTION! This notice indicates a potentially hazardous situation that may result
in minor or moderate injury if proper practices are not taken.
NOTICE! This notice indicates that a specific hazard or unsafe practice will
result in equipment or property damage, but not personal injury.
WORK AREA
1. Operate in a safe work environment. Keep your work area clean, well-lit
and free of distractions. Place lights so you are not working in a shadow.
2. Keep anyone not wearing the appropriate safety equipment away from the
work area.
3. Store unused tools properly in a safe and dry location to prevent rust or
damage. Lock tools away and keep out of the reach of children.
4. Do not install or use in the presence of flammable gases, dust or liquids.
PERSONAL SAFETY
WARNING! Wear personal protective equipment approved by the Canadian
Standards Association (CSA) or American National Standards Institute (ANSI).
PERSONAL PROTECTIVE EQUIPMENT
1. Always wear impact safety goggles that provide front and side protection
for the eyes. Eye protection equipment should comply with CSA Z94.3-07
or ANSI Z87.1 standards based on the type of work performed.
2. Wear the appropriate type of full-face shield in addition to safety googles,
as the work can create chips, abrasive or particulate matter.
3. Wear gloves that provide protection based on the work materials or to
reduce the effects of tool vibration.
4. Wear protective clothing designed for the work environment and tool.
8667834 10 Ton Hydraulic Porta-Power Autobody and Frame Repair Kit V4.0
4 For technical questions call 1-800-665-8685
5. Non-skid footwear is recommended to maintain footing and balance in the
work environment.
6. Wear steel toe footwear or steel toe caps to prevent a foot injury from
falling objects.
PERSONAL PRECAUTIONS
Control the tool, personal movement and the work environment to avoid
personal injury or damage to tool.
1. Do not operate any tool when tired or under the influence of drugs, alcohol
or medications.
2. Avoid wearing clothes or jewelry that can become entangled with the
moving parts of a tool. Keep long hair covered or bound.
3. Do not overreach when operating a tool. Proper footing and balance
enables better control in unexpected situations.
SPECIFIC SAFETY PRECAUTIONS
WARNING! DO NOT let comfort or familiarity with product (gained from
repeated use) replace strict adherence to the tool safety rules. If you use
this tool unsafely or incorrectly, you can suffer serious personal injury.
WARNING! Do not use the porta-power repair kit to lift or support a vehicle.
The pump will fail and the vehicle may move in an unexpected manner,
causing an injury or death.
1. Use the correct tool for the job. This tool was designed for a specific function.
Do not modify or alter this tool or use it for an unintended purpose.
2. Do not use the tool if any parts are damage broken or misplaced. Repair or
replace the parts.
3. Each attachment and extension tube reduces the hydraulic ram’s rated
capacity (see Specifications). See Operation – Reduced Tonnage Capacity.
4. Do not extend the ram beyond the ram stroke length (see Specifications).
5. Do not twist the hydraulic hose (#26).
6. The ram must be properly seated against the workpiece at both ends to
avoid an accident. An accessory at an angle may slip when under pressure
and cause an injury.
V4.0 10 Ton Hydraulic Porta-Power Autobody and Frame Repair Kit 8667834
Visit www.princessauto.com for more information 5
a. Off-set accessories may be used in tandem as long as they are both
properly seated during use.
HYDRAULIC PRECAUTIONS
DANGER! Seek immediate medical attention if hydraulic fluid under pressure
penetrates your skin. See Injection Injury precautions for instructions
before using a pressurized hydraulic system.
1. Do not touch or handle hydraulic hoses or components while under
pressure. Hydraulic fluid escaping under pressure has sufficient force to
penetrate your clothing and skin. A pinpoint hole may inject hydraulic fluid
into your body. Seek immediate medical attention if this occurs (see
Injection Injury).
2. Never exceed the hydraulic system’s load capacity (see Specifications).
3. Do not adjust the hydraulic system’s relief setting. The settings are pre-set
by the factory.
4. Hydraulic oil under pressure is hot and can cause a burn injury if touched,
sprayed or spilled. Allow the hydraulic system to cool before conducting
maintenance.
5. Hydraulic components require regular inspection. Release all pressure
from the system before you inspect it. Replace damaged hydraulic parts
with identical manufacturer's components.
6. Do not attempt makeshift repairs to a hydraulic system. Such repairs can
fail suddenly and create a hazardous condition.
7. A damaged or disconnected hydraulic hose under pressure may whip
around and inflict personal injury or damage the work area. Secure the
hose to a fixed or permanent structure with clamps or cable ties.
8. Hydraulic fluid has a combustible flash point of 200°F (93°F). Do not
expose the fluid to an ignition source.
9. Change your clothing immediately if sprayed with hydraulic fluid. Store
clothing or rags contaminated with hydraulic fluid in an approved metal
safety can with a spring-closing lid and venting designed to contain a fire.
10. Only use hydraulic fluid in the pump. Do not substitute or mix brake fluid,
or any other fluid, with the hydraulic fluid. This can result in a pump failure
and injure the user or bystander. It may also damage the pump.
8667834 10 Ton Hydraulic Porta-Power Autobody and Frame Repair Kit V4.0
6 For technical questions call 1-800-665-8685
INJECTION INJURY
DANGER! Seek immediate, professional medical treatment if fluid penetrates
your skin. It may feel like a pricking or sting. Do not wait for the appearance
of symptoms. A toxic reaction can occur from the exposure. Delay in
treatment can lead to amputation or death.
Inform the medical staff that you have a fluid penetration injury as soon as you
arrive at the medical facility. The severity of the symptoms will depend on the
type of fluid injected. Bring the Safety Data Sheet for the fluid with you to the
medical facility if possible.
INJECTION PRECAUTIONS
Fluid can penetrate the skin at 100 PSI pressure. Fluid escaping under pressure
from the tool has sufficient force to penetrate your clothing and skin. Follow the
precautions below to avoid an injection injury.
1. Always check for leaks wearing a face shield, safety goggles, rubberized
gloves and protective clothes.
2. Release all pressure from the system before you inspect it.
3. Do not use your hands to detect a fluid leak. Use a large piece of wood,
cardboard or paper and watch for discolouration.
4. Replace damaged parts with identical manufacturer's components to
ensure it is rated to handle the pressure.
UNPACKING
WARNING! Do not operate the tool if any part is missing. Replace the
missing part before operating. Failure to do so could result in a malfunction
and personal injury.
Remove the parts and accessories from the packaging and inspect for damage.
Make sure that all items in the Identification Key are included.
V4.0 10 Ton Hydraulic Porta-Power Autobody and Frame Repair Kit 8667834
Visit www.princessauto.com for more information 7
IDENTIFICATION KEY
A Carrying Case
B Hydraulic Pump and Hose
C Ram
D Extension tubes: 3-7/8 in. (98 mm), 7-3/4 in. (197 mm), 11-3/4 in.
(299 mm) and 21-5/8 in. (549 mm)
E Serrated Saddle
F Duckbill Spreader
G Flex Head
H Flat Base
I Ram Toe
J Body Toe
K Wedge Head
L 90º V-Head
M Male Connector
ACCESSORIES
Serrated Saddle (E) – The default attachment. The saddle’s rough surface will
grip a metal workpiece.
Flex Head (G) – The rubber head surface is suitable for popping dents in sheet
metal or working the inner curve of a metal surface without marring it.
Wedge Head (K) – Fits into hard-to-reach areas to push out small dents. Also
suitable for working on angled workpieces.
V-Head (L) – The four peaks and interior ‘steps’ catch and hold angled
workpieces to focus the ram’s pushing force without slipping.
Body Toe (J) – The offset toe can reach difficult locations partially blocked
by the vehicle’s structure. Substitute for the flat base when only a narrow space
is available.
Ram Toe (I) – Offset toe used in conjunction with body toe when using the ram
as a spreader. Screws onto the ram threads.
Fig. 1
8667834 10 Ton Hydraulic Porta-Power Autobody and Frame Repair Kit V4.0
8 For technical questions call 1-800-665-8685
Flat Base (H) – Install on the ram’s base to provide a broad surface to spread
the load during use. Attach using the male connector (M).
Duckbill Spreader (F) – Fits into small spaces and forces the structure apart
when the jaws open. The spreader connects directly to the pump (B).
ASSEMBLY & INSTALLATION
Numbered references in parenthesis (#1) refer to the included Parts List. Letter
references in parenthesis (A) refer to the included Identification Key.
RAM SET-UP
All accessories and adapters are friction fit, except the ram toe (I). Lubricate the
inside of the accessory with grease if it does not slide on until seated.
1. Screw the handle (#12) into the pump’s handle socket (#13).
2. Screw the hydraulic hose (B) onto the ram’s (C) inlet port until hand tight.
3. Slide an accessory onto the ram piston and push it down until fully seated.
4. Press the male connector (M) into the ram end, adding grease as
necessary. Press the flat base (H) or body toe (J) onto the male connector.
Fitting other accessories to the male connector is not recommended. The
ram needs a wide base to distribute the force applied at the other end of
the ram.
5. Add one or more extension tubes (D) between the accessory and the ram
piston or male connector to help fit the ram into a space or reduce the
distance the ram must travel.
a. When using two or more extension tubes together, arrange them with
the longest attached to the ram and the shortest as the final tube
attached to the accessory.
6. Screw the ram toe (I) onto the pump if using it to spread a workpiece.
Remove the plastic cap from the ram to expose the threads. Thread the
ram toe into place until it is tight. Place the body toe on the piston and
make sure it is aligned with the ram toe. Do not attempt to use this set-up
when the body toe is not aligned.
V4.0 10 Ton Hydraulic Porta-Power Autobody and Frame Repair Kit 8667834
Visit www.princessauto.com for more information 9
DUCKBILL SPREADER SET-UP
1. Screw the handle (#12) into the pump’s handle socket (#13).
2. Screw the hydraulic hose (B) onto the duckbill spreader’s (F) inlet port
until hand tight.
OPERATION
The Porta-Power Repair Kit has various attachments to push, pull, stretch and
spread metal structure and panels to reshape them. The pump works in both
the vertical and horizontal position. The oil filling screw must be at the top when
used in a vertical position.
1. Set-up the ram or duckbill spreader. Attach to the pump.
2. Loosen the oil filling screw (#35) several turns to allow air to enter the pump.
3. Open the pump valve (#29) clockwise to allow oil to flow to the ram.
4. Place a block of wood or similar buffer at the end of the accessory that is
bracing the ram to protect the vehicle structure.
5. Pump the handle slowly until the accessory touches the workpiece. Continue
pumping to apply pressure to the workpiece until it is reshaped as desired.
6. Slowly turn the pump valve counterclockwise one turn to release the
pressure and allow the oil to flow back into the pump’s cylinder. Tighten
the pump valve.
7. Tighten the oil filling screw until tight.
8. Remove and store the attachments and extensions.
ACCESSORY
Each accessory can be used by itself or in conjunction with other accessories to
apply force against a vehicle’s panels and frame to reshape or realign them.
REDUCED TONNAGE CAPACITY
The base ram set-up is an accessory directly attached to the ram piston and
another to the base via the male connector. This retains the full tonnage capacity
(see Specifications). Reduce the tonnage capacity by 50 percent for each extra
attachment or extension tube added to the ram. Two extension tubes or an
extension tube with another accessory will reduce the tonnage capacity to 25
percent (10 ton to 5 ton for extension tube to 2.5 ton for the third attachment).
8667834 10 Ton Hydraulic Porta-Power Autobody and Frame Repair Kit V4.0
10 For technical questions call 1-800-665-8685
Always use the longest extension tube possible to avoid minimizing the
tonnage capacity.
ADAPTERS
Extension Tubes (D) extend the ram’s reach between 3-7/8 to 45 in. Extension
tubes are attached end-to-end from. Always arrange multiple extension tubes
with the longest piece connected to the ram piston and the shortest piece
connected to the accessory.
The male connector (M) is inserted into the ram’s base. Accessories or
extension tubes can then be attached to the ram.
PUSHING
The primary method to modify the structure is pushing the damaged structure
back into place
1. Install the flat base or body toe at the bottom of the ram. This provides a flat
area to brace against and spreads out the force, allowing the narrower
accessory on the piston head to concentrate the force and reshape the metal.
2. Determine the distance between the bracing point and the damaged structure
by holding the ram in place. Add extension tubes to the piston end to extend
the reach, remembering to accommodate the length of the accessory. The
distance left should be less than the ram piston’s stroke length (see
Specifications). Stop and add additional extension tubes as needed.
a. Depending on the workspace, you may need to add an extension
between the ram and the flat base/toe plunger to fit it into the
available space.
3. Choose the appropriate accessory based on the type of repair being
attempted and install it on the ram piston.
a. The body toe (J) must be aligned so the offset flange is aligned with
the length of the flat base. This will keep the force parallel to the
direction of the bend. Using the body toe to push in any other
configuration can result in a failure and result in damage or injury.
This does not apply when using the body toe as a base.
V4.0 10 Ton Hydraulic Porta-Power Autobody and Frame Repair Kit 8667834
Visit www.princessauto.com for more information 11
SPREADING
Spreading is used to move two parts of a structure away from a central point.
There are three options: the duckbill spreader for short distances, the ram toe
and body toe for distances up to nearly 6 inches and a pushing set-up for larger
distances.
DUCKBILL SPREADER
WARNING! Keep fingers away from the duckbill spreader when opening or
closing. The hydraulic or spring pressure can crush or pinch an appendage
causing a crushing injury.
1. Set-up the duckbill spreader.
2. Wedge the closed jaws into available space. If the space is slightly larger,
hold the duckbill spreader into position until it spreads enough to be held
in place.
3. Begin pumping until the spreader is firmly held in position. Continue to
pump to widen the jaws until the metal workpiece is separated to the
desired gap or the jaws are at their maximum width.
4. Release pressure until the jaws are shut.
RAM TOE AND BODY TOE
Both the body toe and ram toe have offset flanges. The two parts are always
used together to separate a damaged workpiece. Using just one or the other can
cause an unbalanced load on the ram.
1. Set-up the ram toe and body toe on the hydraulic pump. Add extension tubes
until the body toe is within six inches of the gap between the two sides of the
workpiece. Remember each extension reduces the force by 50 percent.
2. Place the ram toe flush against the inside of the workpiece.
3. Hold the ram in place if necessary. Slowly pump until the body toe is firmly
seated against the opposite inner surface. Check that the body toe and ram
toe are still aligned.
4. Pump to spread the workpiece until it has reached the desired point.
a. You may need to add another extension tube or replace an existing
one with a longer tube to complete the task if the ram has reached its
full extension.
5. Release pressure until the piston fully retracts.
8667834 10 Ton Hydraulic Porta-Power Autobody and Frame Repair Kit V4.0
12 For technical questions call 1-800-665-8685
CARE & MAINTENANCE
1. Maintain the tool with care. A tool in good condition is efficient, easier to
control and will have fewer problems.
2. Inspect the tool components periodically. Repair or replace damaged or
worn components. Only use identical replacement parts when servicing.
3. Follow instructions for lubricating and changing accessories.
4. Only use accessories intended for use with this tool.
5. Keep the tool handles clean, dry and free from oil/grease at all times.
6. Maintain the tool’s labels and name plates. These carry important information.
If unreadable or missing, contact Princess Auto Ltd. for replacements.
WARNING! Only qualified service personnel should repair the tool. An
improperly repaired tool may present a hazard to the user and/or others.
HYDRAULIC RAM MAINTENANCE
Monthly maintenance is recommended for the hydraulic ram. Any restrictions
due to dirt, rust, etc. can cause the either slow movement or extremely rapid
jerks, damaging the internal components. The following steps are designed to
keep the pump maintained and operational.
1. Lubricate the cylinder and the pumping mechanism with light oil.
2. Visually inspect for cracked welds, bent, loose, missing parts or hydraulic
oil leaks.
3. Inspect the hydraulic ram immediately if it was subjected to an abnormal
load or shock load.
4. Remove any hydraulic pump from service that is damaged, worn down or
operates abnormally, until repaired by an authorized service technician.
5. Check and maintain the ram oil level.
a. Lower the ram piston fully. Lay the hydraulic pump in the horizontal
position.
b. Remove the oil filler screw to check the hydraulic oil level. Replace the
oil filler screw if the level is adequate and ignore the next two steps.
c. Add high quality hydraulic jack oil If the level is low. Fill to within half
an inch from the opening.
d. Bleed the hydraulic pump.
V4.0 10 Ton Hydraulic Porta-Power Autobody and Frame Repair Kit 8667834
Visit www.princessauto.com for more information 13
6. Always store the hydraulic ram in the fully retracted position. This will help
protect critical areas from corrosion.
7. Do not use brake or transmission fluids or regular motor oil as they can
damage the seals. Always purchase and use products labeled Hydraulic Oil.
BLEEDING THE HYDRAULIC SYSTEM
Bleed excess air from the hydraulic system as follows:
1. Open the release valve by turning it counterclockwise.
2. Remove the oil filler screw and fill the pump with hydraulic fluid.
3. Wait 5 minutes for trapped air to rise to the surface.
4. Pump the handle or pedal for several full strokes to eliminate any air in
the system.
5. Check the oil filler hole and if necessary, top off with more hydraulic oil.
6. Restore the oil filler screw. Close the release valve by turning clockwise.
7. Test the ram several times for proper operation before putting it into use. Do
not use the ram if it still does not appear to be working properly. Have a
qualified service technician service or repair the hydraulic system.
DISPOSAL
Recycle a tool damaged beyond repair at the appropriate facility.
Contact your local municipality for a list of disposal facilities or by-laws for
electronic devices, batteries, oil or other toxic liquids.
IMPORTANT! DO NOT pollute the environment by allowing uncontrolled
discharge of waste oil.
DISPOSAL - HYDRAULIC FLUID
Do not drain hydraulic oil into the sewer system or dispose in an uncontrolled
location. Hydraulic fluid may take more than a year to breakdown in the
environment and the ingredients may still be toxic. Contact your local
municipality for proper disposal instructions or locations.
8667834 10 Ton Hydraulic Porta-Power Autobody and Frame Repair Kit V4.0
14 For technical questions call 1-800-665-8685
TROUBLESHOOTING
Visit a Princess Auto Ltd. location for a solution if the tool does not function
properly or parts are missing. If unable to do so, have a qualified technician
service the tool.
Problem(s) Possible Cause(s) Suggested Solution(s)
Ram will not move
against load.
1. Release valve not tightly
closed.
2. Overloaded pump.
3. Air trapped in system.
1. Firmly close release valve.
2. Reduce load.
3. Bleed the hydraulic system.
Ram fails to
maintain load.
1. Release valve not tightly
closed.
2. Hydraulic unit malfunction.
1. Firmly close release valve.
2. Replace ram and/or pump.
Ram will not retract
after unloading.
1. Reservoir overfilled.
2. Linkages binding.
1. Drain oil to proper level.
2. Clean and lubricate moving
parts.
Ram will not extend
to full stroke.
1. Oil level low. 1. Add hydraulic oil.
Poor performance. 1. Oil level low.
2. Air trapped in system.
1. Add hydraulic oil.
2. Bleed the hydraulic system.
V4.0 10 Ton Hydraulic Porta-Power Autobody and Frame Repair Kit 8667834
Visit www.princessauto.com for more information 15
PARTS BREAKDOWN
PARTS LIST
# DESCRIPTION QTY
1 Pin 1
2 Movable Jaw 1
3 Fixed Jaw 1
4 Retaining Ring 2
5 Torsion Spring 1
6 Assembled Union 1
6.1 Connection Nut 2
6.2 Cylinder Screw 2
6.3 O-Ring 2
6.4 Dust Proof Cover 2
7 Screw Cover 1
8 O-Ring 1
9 Piston Ring 1
10 Small Piston 1
11 Handle Sleeve 1
8667834 10 Ton Hydraulic Porta-Power Autobody and Frame Repair Kit V4.0
16 For technical questions call 1-800-665-8685
# DESCRIPTION QTY
12 Handle 1
13 Handle Socket 1
14 Retaining Ring 2
15 Pin 1
16 Pin 1
17 Plunger 1
18 Plunger Cover 1
19 Nylon Gasket 1
20 O-Ring 1
21 O-Ring 1
22 Filter Gauze 1
23 Ball 3
24 Coupler 1
25 Dust Proof Cover 1
26
Hydraulic Hose
1
27 Y-Seal 1
28 Screw 1
29 Pump Valve 1
30 Screw 1
31 Seal Ring 1
32 Valve Block 1
33 Oil Filter 1
34 Reservoir 1
35 Oil Filling Screw 1
36 O-Ring 3
37 Taper Spring 1
38 O-Ring 1
39 Reservoir Cover 1
39.1 Screw 1
40 O-Ring 1
41 Ball 1
42 Ball Seat 1
43 Spring 1
44 Adjusting Screw 1
45 Screw 1
46 Screw Cover 1
47 Retaining Ring 1
48
Pull Bar
1
49 Nylon Sealing Ring 1
50 Bowl 1
51 Retaining Ring 1
52 Ram Piston 1
53 Cover 1
54 Pull Spring 1
55 Screw Cover 1
56 Ring For Ram 1
57 Cylinder 1
V 4,0 8667834
Vous devez lire et comprendre toutes les instructions avant d'utiliser l'appareil.
Conservez ce manuel afin de pouvoir le consulter plus tard.
Manuel d'utilisateur
Trousse de réparation
hydraulique de carrosserie et de
châssis Porta-Power, 10 tonnes
8667834 Trousse de réparation hydraulique de carrosserie V 4,0
et de châssis Porta-Power, 10 tonnes
2 En cas de questions techniques, appelez le 1-800-665-8685
SPÉCIFICATIONS
Capacité Hydraulic Ram 10 tonnes (20 000 lb)
Duckbill Spreader 0,5 tonnes (1 000 lb)
Patte de corps/patte de vérin 0,8 tonnes (1 600 lb)
Pression continue max. 8 900 lb/po carré
Course du vérin 130 mm (5 po)
Plage de l’écarteur bec de canard 83 mm (3 1/4 po)
INTRODUCTION
La trousse de réparation hydraulique Porta-Power pour carrosserie et châssis
d’une capacité de 10 tonnes est essentielle pour réparer des carrosseries et des
châssis de véhicule. La trousse redresse, cintre ou sépare le métal pour réparer
les dommages causés par les collisions deux fois plus rapidement que les
méthodes de frappe conventionnelles.
La pompe se caractérise par une course de 5 po avec une portée de rallonge de
13 5/8 à 18 3/4 po. Des tubes de rallonge à conception de verrouillage rapide
permettent l’assemblage rapide et facile. Un système de surcharge de pompe
automatique aide à prévenir les dommages au vérin et aux accessoires.
SÉCURITÉ
AVERTISSEMENT ! Veuillez lire et comprendre toutes les instructions avant
d'utiliser cet outil. L'utilisateur doit respecter les précautions de base
lorsqu'il utilise cet outil afin de réduire le risque de blessure ou de
dommage à l'équipement.
Conservez ce manuel qui contient les avertissements de sécurité, les
précautions, les instructions de fonctionnement ou d'inspection et d'entretien.
Trousse de réparation
hydraulique de carrosserie et de
châssis Porta-Power, 10 tonnes
V 4,0 Trousse de réparation hydraulique de carrosserie 8667834
et de châssis Porta-Power, 10 tonnes
Visitez www.princessauto.com pour plus d'informations 3
DÉFINITIONS DE DANGER
Veuillez-vous familiariser avec les avis de danger qui sont présentés dans ce
manuel. Un avis est une alerte indiquant qu'il existe un risque de dommage à la
propriété, de blessure ou de décès si on ne respecte pas certaines instructions.
DANGER ! Cet avis indique un risque immédiat et particulier qui
entraînera des blessures corporelles graves ou même la
mort si on omet de prendre les précautions nécessaires.
AVERTISSEMENT ! Cet avis indique un risque particulier ou une pratique non
sécuritaire qui pourrait entraîner des blessures
corporelles graves ou même la mort si on omet de
prendre les précautions nécessaires.
ATTENTION ! Cet avis indique une situation possiblement dangereuse qui
peut entraîner des blessures mineures ou modérées si on
ne procède pas de la façon recommandée.
AVIS ! Cet avis indique un risque particulier ou une pratique non
sécuritaire qui entraînera des dommages au niveau de
l'équipement ou des biens, mais non des blessures corporelles.
AIRE DE TRAVAIL
1. Travaillez dans un environnement de travail sécuritaire. Gardez votre aire
de travail propre, bien éclairée et exempte de toute distraction. Placez les
lampes de façon à ne pas travailler dans l’ombre.
2. Assurez-vous que les personnes qui ne portent pas l'équipement de
sécurité approprié ne se trouvent pas à proximité de l'aire de travail.
3. Rangez les outils correctement dans un lieu sécurisé et sec. Gardez les
outils hors de la portée des enfants.
4. N'installez pas et n'utilisez pas d'outils électriques en présence de gaz, de
poussière ou de liquides inflammables.
8667834 Trousse de réparation hydraulique de carrosserie V 4,0
et de châssis Porta-Power, 10 tonnes
4 En cas de questions techniques, appelez le 1-800-665-8685
SÉCURITÉ PERSONNELLE
AVERTISSEMENT ! Portez de l'équipement de protection personnelle
homologué par l'Association canadienne de normalisation (CSA) ou
l'American National Standards Institute (ANSI).
ÉQUIPEMENT DE PROTECTION PERSONNELLE
1. Portez toujours des lunettes antiprojections qui offrent une protection
frontale et latérale pour les yeux. L'équipement de protection des yeux
devrait être conforme à la norme CSA Z94.3-07 ou ANSI Z87.1 fonction du
type de travail effectué.
2. Portez un écran facial panoramique de type approprié avec les lunettes de
sécurité puisque cette tâche peut créer des copeaux, des matières
abrasives ou des particules.
3. Portez des gants qui protègent en fonction des matériaux de travail et pour
réduire les effets des vibrations de l'outil.
4. Portez des vêtements de protection conçus pour l'environnement de travail
et pour l'outil.
5. Les chaussures antidérapantes sont recommandées pour maintenir la
stabilité et l'équilibre au sein de l'environnement de travail.
6. Portez des chaussures à embout d'acier ou à coquilles d'acier pour éviter
les blessures aux pieds dues à la chute d'objets.
PRÉCAUTIONS PERSONNELLES
Gardez le contrôle de l'outil, de vos mouvements et de l'environnement de
travail pour éviter les blessures ou le bris de l'outil.
1. N'utilisez pas l'outil si vous êtes fatigué ou sous l'effet de drogues, d'alcool
ou de médicaments.
2. Évitez de porter des vêtements ou des bijoux pouvant se prendre dans les pièces
mobiles d'un outil. Gardez les cheveux longs recouverts ou attachés.
3. N'utilisez pas l'outil si vous devez étirer les bras pour vous en servir. Une
stabilité et un équilibre appropriés sont nécessaires afin d'avoir un meilleur
contrôle en cas de situations inattendues.
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
Powerfist 8667834 Le manuel du propriétaire
- Taper
- Le manuel du propriétaire
dans d''autres langues
- English: Powerfist 8667834 Owner's manual