Battery Free Wirelessly
Powered Sensor EVK
QUICK START GUIDE
2
Quick Start Guide
This guide will help you to setup and operate your
EVK, demonstrating the capabilities of this battery
free wirelessly powered sensor.
Figure 1: System Diagram
3
Box Contents
• 1W WattUp PowerBridge Transmitter (1)
• Battery-Free IoT Sensors (2)
• 5V/1A USB power adapter and USB-A to -C cable
Box Contents:
Figure 2: EVK Box and Contents
Setup & Operation
4
1. Setup the Powerbridge
• Connect the USB cable to the PowerBridge Transmitter
and the power supply.
• Mount the PowerBridge on a stand, a wall or a ceiling
using keyhole screw mounts in a position pointing
toward the sensors.
Figure 3: Mounting Diagram
5
TitleSetup the Powerbridge Cont’d.
• Plug in the PowerBridge power supply.
• After power-on, the Blue LED fl ashes for 30s to indicate
that the PowerBridge is running.
• The PowerBridge starts RF power transmission
automatically, with the white LED indicating that the
PowerBridge is now transmitting.
Blue LED
White LED
Figure 4: Wattup PowerBridge Front
6
2. Position the Sensors
3. Reading the Sensor Data
• Position the sensors within ~1.5m of the PowerBridge.
• The battery free sensors are now receiving wireless
power from the PowerBridge.
• Once the sensors receive suffi cient power, they will
begin taking sensor measurements (Temperature,
Humidity, and 3D Accelerometer data), and sending
via BLE advertisements.
• Maintain a minimum separation of at least 0.3m
between the sensors and the PowerBridge.
• Download the Atmosic DevTools App from the
Android or Apple Store.
Figure 5: Apple Store QR code
for Atmosic DevTools App
Figure 6: Google Play QR code
for Atmosic DevTools App
7
4. Using the Atmosic DevTools App
Open the App, and tap the
Applications button:
The sensor beacons will appear with
the name “Atmosic BCN” followed by
a serial number used to distinguish
the beacons. Tap the Monitor button
to start displaying the sensor data:
The sensor data displayed
includes the Received Signal
Strength from the sensor (RSSI),
Temperature, Humidity, and
accelerometer data:
Tap the Beacon button to start
scanning for beacons:
8
5. Typical Sensor Range
• Time to initial sensor data measurement:
The sensors store energy on an internal capacitor.
Without energy from an RF source, the capacitors
will discharge over the course of 8 to 10 minutes.
• Once discharged, it will take approximately 4 to 6
minutes at a distance of 1.5 meters to recharge the
capacitor and enable sensor transmissions.
• Sensor Placement:
The Sensor can be placed horizontally or vertically.
Figure 11: Sensors Receiver, Vertical and Horizontal
9
The Sensor will receive power in an area approximately +/-
30 degrees from boresight to the PowerBridge Transmitter.
There will be some small amount of performance delta
depending on the rotation of the Sensor relative to
boresight from the PowerBridge Transmitter.
Typical Sensor Range Cont’d.
Figure 12: PowerBridge Transmitter and Atmosic Sensor Receivers
0.75m
30º
60º
1.5 m
1.3 m
10
FCC Regulatory Information
FCC ID: 2ADNG-VN25 Model: VN25
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference, and (2)
This device must accept any interference received, including
interference that may cause undesired operation.
Note: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment o
and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the equipment being interfered with.
• Increase the separation between the charger and the equipment
subject to interference.
• Connect the equipment into an outlet on a circuit dierent from
that to which the charger is connected.
• Consult the dealer or an experienced radio/TV/electronics
technician for help.
CAUTION: Changes or modications to this unit not expressly
approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
11
FCC Regulatory Information Cont’d.
VN25 RF wireless charger complies with FCC RF radiation exposure
limits for an uncontrolled environment in accordance with FCC
Rule Part 2.1093. The Wireless charger transmitter is designed to
be installed on the ceiling or on a side wall and must be installed
accordingly to ensure a minimum 20cm separation distance from
persons.
IC: 23686-VN25, Model: VN25
This device complies with Industry Canada’s licence-exempt RSSs.
Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including
interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada
applicables aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes :
(1) l’appareil ne doit pas produire de brouillage;
(2) l’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.
VN25 RF wireless charger complies with ISED radiation exposure
limits. The Wireless charger transmitter is designed to be installed
on the ceiling or on a side wall and must be installed accordingly
to ensure a minimum 22cm separation distance from persons.
Le chargeur sans l RF VN25 est conforme aux limites d’exposition
aux rayonnements ISED. L’émetteur du chargeur sans l est conçu
pour être installé au plafond ou sur un mur latéral et doit être
installé en conséquence pour assurer une distance de séparation
minimale de 22 cm des personnes.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
dans d''autres langues
- English: energous EVK User guide
Autres documents
-
COREKINECT BLELRA1 Manuel utilisateur
-
Daintree Networked WMZ10 People Counting Sensor Guide d'installation
-
Ecolab HHCM915 Hand Hygiene Program Mode d'emploi
-
Vernier Go Wireless Exercise Heart Rate Manuel utilisateur
-
-
Tobii Dynavox I-SERIES Manuel utilisateur
-
Eurotech ReliaGATE 20-25 Le manuel du propriétaire
-
Eurotech ReliaGATE 10-12 Le manuel du propriétaire
-
-
