DoorBird D10x Guide d'installation

Taper
Guide d'installation
VERSION ., MIN. HW .
Page 1-19
Installation Manual
IP Video Door Station
D10x Series
Seite 20-39
Installationsanleitung
IP Video Türstation
D10x Serie
Page 40-58
Manuel d´installation
Interphone vidéo IP
Série D10x
Página 59-77
Manual de Instalación
Videoportero IP
Serie D10x
Pagina 78-95
Manuale di installazione
Videocitofono IP
Serie D10x
D10X
2
INSTALLATION MANUAL
Read these instructions carefully before starting to use any components.
Keep the manual so you can refer to it at a later date if required. If you hand
over the device to other persons for use, please hand over the operating
manual as well.
You can always find the most up-to-date version of the installation manual
on www.doorbird.com/support
To make things easier we use the term “device” for the product “IP Video
Door Station” and “mobile device” for a smartphone or tablet.
Liability
Every care has been taken in the preparation of this document.
Please inform Bird Home Automation GmbH of any inaccuracies or omissions.
Bird Home Automation GmbH cannot be held responsible for any technical
or typographical errors and reserves the right to make changes to the product
and manuals without prior notice. Bird Home Automation GmbH makes no
warranty of any kind with regard to the content of this document, including,
but not limited to, the implied warranties of merchantability and fitness for
a particular purpose. Bird Home Automation GmbH shall neither be liable
nor responsible for incidental or consequential damages in connection with
the furnishing, performance or use of this material. This product is only to
be used for its intended purpose.
Equipment Modifications
This equipment must be installed and used in strict accordance with the
instructions given in the user documentation. This equipment contains no
components that require service by the user. Unauthorized equipment
changes or modifications will invalidate all applicable regulatory certifications
and approvals.
Symbols used
Caution: Indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.
Danger: Indicates a hazardous situation which, if not avoided,
will result in death or serious injury.
Warning: Indicates a hazardous situation which, if not avoided,
could result in death or serious injury.
Notice: Indicates a situation which, if not avoided, could result
in damage to property.
NOTICE
3
ENGLISHENGLISH
Note: Indicates useful information which helps in getting the
most out of the product.
Hazard information
Mounting, installation and servicing work on electrical devices may
only be performed by a qualified eletrician. Failure to observe this
regulation could result in the risk of serious damage to health or fatal
injury due to electric shocks.
Devices with 110-240 V connection: The device may only be connected
to an easily accessible power socket outlet. The mains adapter must
be pulled out if a hazard occurs.
For power supply, only use the original plug-in mains adapter
delivered with the device or a recommended PoE-Switch/PoE-Injector
as specified in this manual.
Because of electrostatic charging, direct contact with the circuit board
can result in destruction of the device. Direct contact with the circuit
board must therefore be avoided at any time.
Observe the EN 60065 resp. EN 60950 resp. EN 62368 standard.
Do not use the device if there are signs of damage to the housing,
control elements or connecting sockets, for example, or if it
demonstrates a malfunction. If you have any doubts, please have
the device checked by an authorized expert.
Do not open the device. This voids the warranty of the device. The
device does not contain any parts that can be maintained by the
user. In the event of an error, please have the device checked by an
authorized expert.
For safety, approval and licensing reasons (CE/FCC/IC etc.),
unauthorized change and/or modification of the device is not
permitted.
The device is not a toy: do not allow babies and children to play with
it.
To avoid the danger of suffocation, keep any packing materials away
from babies and children. Plastic films/bags, pieces of polystyrene, etc.
are not a toy and can be dangerous in the hands of a child. Discard
WARNING
Important: Indicates significant information which is essential
for the product to function correctly.
4
any packing materials immediately after removing the product. Do not
reuse packing materials.
Always lay cables in such a way that they do not become a risk to
people and domestic animals.
Voltage is applied to parts within the equipment. Do not touch any
parts that are not associated with the installation, wiring, or connection.
Electric shock could result.
On devices which are not marked as weather-proof: Keep the device
away from water or any other liquid.
Do not install or make any wire terminations while power supply is
plugged in. It can cause eletric shock or damage to the device.
Before turning on power, make sure wires are not crossed or shorted. If
not, fire or eletric shock could result.
High voltage may be present internally. Do not open the device.
Electric shock could result.
The device is not of explosion-proof. Do not install or use near gases or
flammable materials. Fire or explosion could result.
Do not install two power supplies in parallel to a single input. Fire or
damage to the device could result. Be sure to connect a single power
supply to the device.
Do not connect any terminal on the device to an AC power line. Fire or
electric shock could result.
Keep AC cord from being marred or crushed. If the AC cord is fractured,
fire or electric shock could result.
Do not plug or unplug with wet hands. Electric shock could result.
Do not put any metal or flammable material into the device. Fire,
electric shock, or device trouble could result.
Existing wiring may contain high voltage AC electricity. Damage to the
device or electric shock could result. Wiring and installation must be
done by a qualified eletrician.
When mounting the device on a wall or ceiling, install the device in a
convenient location, but not where it could be jarred or bumped. Injury
could result.
On devices with ground terminals, connect to an earth ground.
Otherwise fire or malfunction could result.
On devices with plastic or real glass, do not put high pressure on the
glass. If fractured, injury could result.
WARNING
5
ENGLISHENGLISH
On devices with LCD, if LCD is punctured, do not allow contact with the
liquid crystal inside. Injury could result. If necessary, gargle your mouth
and clean your eyes or skin with clear water for at least 15 minutes and
consult your doctor.
Do not put anything on the device or cover the device with cloth,
silicone, glue, coating, separate covering etc. Fire or device issues could
result.
Do not install the device in any of the following locations. Fire, electric
shock, or device trouble could result.
Places under direct sunlight or places near heating equipment that
varies in temperature.
Places subject to dust, oil, chemicals, hydrogen sulfide (hot spring).
Places subject to moisture and humidity extremes, such as bathrooms,
cellars, greenhouses, etc.
Places where the temperature is very low, such as inside a refrigerated
area or in front of an air conditioner.
Places subject to steam or smoke (e.g. near heating or cooking surfaces).
Where noise generating devices such as dimmer switches or inverter
electrical appliances are closeby.
Locations subject to frequent vibration or impact.
On devices with intercom, be sure to perform a call test with low audio
volume on both intercom devices. A sudden call etc. may arrive causing
for example damage to your ear.
If the device does not operate properly, unplug the power supply.
All devices which are not marked as weather-proof are designed for
indoor use only. Do not use outdoor.
On devices which are marked weather-proof: Do not spray with high-
pressure water. Device issues could result.
We do not assume any liability for damage to property or personal injury
caused by improper use or the failure to observe the
hazard information. In such cases, any claim under warranty ceases. For
consequential damages, we assume no liability!
6
Safety instructions
The device shall be used in compliance with local laws and regulations.
Store the device in a dry and ventilated environment.
Avoid exposing the device to shocks or heavy pressure.
Do not install the device on unstable brackets, surfaces or walls. Make
sure the material is strong enough to support the weight of the device.
Use only applicable tools when installing the device. Using excessive
force with tools could cause damage to the device.
Do not use chemicals, caustic agents, or aerosol cleaners.
Use a clean dry cloth for cleaning.
Use only accessories that comply with technical specification of the
device. These can be provided by Bird Home Automation GmbH.
Use only spare parts provided by or recommended by Bird Home
Automation GmbH.
Do not attempt to repair the device by yourself. Contact Bird Home
Automation GmbH for service matters.
Keep the device more than 1 m (3.3‘) away from microwave, radio, TV,
wireless router and any other wireless devices.
On devices with intercom or built-in speaker or built-in microphone or
signal transmission functions, keep the wires more than 30 cm (12‘‘)
away from AC 100-240 V wiring. AC induced noise and/or device
malfunction could result.
Install the device in an area that will be accessible for future inspections,
repairs and maintenance.
If the device is used close to a cellular phone, the device may malfunction.
The device can be damaged if dropped. Handle with care.
The device turns inoperative during power failure.
On devices with intercom or built-in speaker or built-in microphone,
in areas where cellular or Radio / TV broadcasting station antennas are
closeby, the device may be affected by radio frequency interference.
On devices with LCD screen, it must be noted in advance that the LCD
panel, though manufactured with very high precision techniques,
inevitably will have a very small portion of its picture elements always lit
or not lit at all. This is not considered a device malfunction.
NOTICE
7
ENGLISHENGLISH
On devices with intercom, due to the environmental sound around
the device, it may hinder smooth communication, but this is not a
malfunction.
On devices with Username/Password, the Username/Password to access
the device is the customer‘s responsibility. Make sure to use a password
that cannot be easily guessed by a third party. We recommend that
you change the Password on a regular basis.
We will, under no circumstances, be liable for damage that occurs due
to failures in power supply, network equipment or terminal devices;
failures due to Internet providers and cellular network providers; failures
such as disconnected lines and other losses in communication, which
makes it impossible to provide this service as well as in any way delay
this service due to any other causes outside of our responsibility; or if an
error or missing data occurs during transmission.
Information on disposal for users of waste electrical & electronic
equipment (private household)
This symbol on the products and/or accompanying documents means that
used electrical and electronic products should not be mixed with general
household waste. For proper treatment, recovery and recycling, please take
these products to designated collection points, where they will be accepted
an a free of charge basis. Alternatively, in some countries you may be able to
return your products to your local retailer upon the purchase of an equivalent
new product. Disposing of this product correctly will help to save valuable
resources and prevent any potential negative effects on human health and
the environment which could otherwise arise from inappropriate waste
handling. Please contact your local authority for further details of your nearest
designated collection point. Penalties may be applicable for incorrect disposal
of this waste, in accordance with national legislation.
Information on disposal in other countries outside the European Union
This symbol is only valid in the European Union. If you wish to discard this
product, please contact your local authorities or dealer and ask for the correct
method of disposal.
8
COMPONENTS
Contents
1x DoorBird Video Door Station
1x Power supply unit (mains adaptor) with four country-specific adaptors
1x Cable with plug for the power supply (black, red)
1x Cable with plug and RJ45 jack for the network cable (white-orange,
orange, white-green, green)
1x Cable with plug for the network cable (white-orange, orange,
white-green, green), alternatively to the cable with plug and RJ45 jack
1x Cable with plug for the electric door opener (purple, purple)
1x Cable with plug for the electric door chime (blue, blue)
1x Cable with plug for the door-opening button (yellow, yellow)
Several crimp connectors
4x Phillips countersunk head screws for the wall mounting plate, long
4x Phillips countersunk head screws for the wall mounting plate, short
4x Dowels
1x Safety screw
1x Screwing-tool for the safety screw
1x Wall mounting plate with sealing ring (installation on wall surface)
1x Installation manual
1x Quickstart guide
Warranty Information
For information about the device warranty, see www.doorbird.com/warranty
Transportation
When transporting the device, use the original packaging or
equivalent to prevent damage to the device.
NOTICE
9
ENGLISHENGLISH
VIDEOS
Need help with the installation? Be sure to watch our installation videos
which can be found on http://www.doorbird.com/support
Each individual step of the installation is clearly documented in the videos.
Video door station
1) Night vision
Extra bright infra-red LEDs, effective
during the hours of darkness
(infra-red light invisible to the
human eye, 850nm)
2) HDTV video
Ultra wide-angle hemispheric
lens, 180°
3) Loudspeaker
Large-sized and speech enhanced
broadband speaker
4) Motion sensor
180° Infrared motion sensor
for alarms
5) Stainless-Steel Button
With illuminated LED ring (at night),
also acts as Diagnostic-LED
6) Microphone
With active noise cancellation
7) Light sensor
For the night-vision mode
8) Locking positions
For the mounting plate
9) Connection terminal
For the power supply,
door chime, etc.
10) Screw opening
For the safety screw
Night vision
HDTV video
Loudspeaker
Motion sensor
Stainless-Steel
Button
Microphone
Light sensor
backfront
1 8
9
10
2
3
4
5
6
7
10
INSTALLATION
All steps below should be carried out carefully by a competent adult, taking
into consideration any applicable safety regulations. Should you have any
questions, please contact us or a competent specialist directly. Please ensure
that all wires used for the installation are undamaged along their entire
length and approved for this type of use.
Network speed and network components
Please ensure that the upload speed of your Internet connection is at least
0.5 Mbps. You can also carry out a speed test at any time via the DoorBird
app. The user experience is only as good as your network speed, network sta-
bility and quality of your network components, such as your Internet router
and WiFi access points or WiFi repeaters. Please also make sure that your net-
work components are no older than two years old, have been manufactured
by a well-known manufacturer, and have the latest firmware installed.
Should these requirements not be fulfilled, it may happen, for example that
the performance of audio and video is poor or push notifications are delayed
or do not arrive on your smartphone or tablet at all.
High-speed Internet (via landline): DSL, cable or optical fibre
Network: 802.11b/g/n 2.4 GHz or Ethernet, with DHCP
STEP 1: SWITCHING OFF POWER
Switch off the power to all wires leading to the assembly location, i.e. the
door chime, electric door opener, power supply unit for the video door
station etc..
STEP 2: DISMANTLING THE EXISTING DOORBELL
Should there already be a doorbell on the exterior wall of the house, please
dismantle it.
STEP 3: DETERMINING THE ASSEMBLY LOCATION
The video door station uses an ultra wide-angle hemispheric lens so that
even when the person is a minimum distance of 50 cm (19.68 inches) away
from the video door station, a low installation height is sufficient. The lens is
therefore not mechanically adjustable. The camera lens should be located
at an altitude of at least 145 cm (57 inches). You may check this prior to the
final mounting. Press the mounting plate against the wall at the desired
installation site and mark the boreholes with a pencil. Remove the mounting
plate again. Ensure that no cables are to be found in the wall behind
the boreholes.
11
ENGLISHENGLISH
Do not expose the device to direct sunlight. The housing temperature
can exceed the maximum allowed temperature limit. This can result
in damage of electric and mechanic components of the device and
injuries especially when touching exterior parts of the device. White
and bright silver-colored front plates absorb less sunlight than dark
ones.
An image sensor must not be exposed to direct sunlight for an
extended period of time. Direct sunlight will “blind” the camera
and may permanently bleach the small color filters on the image
sensor chip.
Any defects caused by direct sunlight is not covered by warranty.
STEP 4: POWER SUPPLY
The video door station can be powered by two simple doorbell wires using
the power-supply unit (mains adaptor) supplied with it or via PoE (Power
over Ethernet) using a network cable. The video door station can alternatively
also be supplied with a DIN-rail power supply unit that you can obtain from
us directly.
The video door station does not use battery power. The use of a mains power
supply permits the transmission and display of on-demand live video at any
time and not only if a visitor has pressed the doorbell.
Power supply using the power-supply unit (mains adaptor)
Two insulated wires are required to power the video door station by plugging
it into the mains. These wires are normally already there and are freely
accessible once you have removed the previous doorbell. Only use the power
supply unit provided along with the video door station, or a DIN-rail power
supply unit that you can obtain from us separately, since this has been spe-
cially stabilized electrically and is equipped with an integrated audio interfe-
rence reduction device. Other power supply units may destroy the video door
station or cause poor transmission quality. The warranty automatically expi-
res if you use a different power supply unit. The power supply unit is plugged
into a wall socket inside your house, usually where the two wires from your
previous doorbell come out of the wall in the interior of the house.
Do not plug the power supply unit into the wall socket yet. Connect the po-
wer supply unit inside the house with the crimp connector provided and the
two wires that you would like to use to power the device.
NOTICE
NOTICE
12
STEP 5: FURTHER CONNECTIONS (OPTIONAL)
If desired, connect additional wires to the installation site of the video door
station. The wires or connection options mentioned in this section are optional.
Be sure to use
four insulated,
shielded and
twisted wires of
a network cable
in accordance
with the Cat.5
standard or
better.
Connecting the unit to a network
You can connect the video door station to your existing
network via WiFi, or alternatively use a network cable
(Ethernet). For reasons of network stability, we principally
recommend using a network cable, as WiFi is sensitive to
interference (range, house walls acting as shields, relia-
bility of performance, third party WiFi networks, wireless
transmitters causing interference in the area, etc.).
The video door station can be powered by PoE or using
the power supply unit provided. If you use PoE as a
source of power, the WiFi interface of the video door
station remains inactive.
Use only four wires (1, 2, 3 and 6) of a network cable that
meets the Cat.5 standard or a better one. The other four
wires of the network cable (4, 5, 7 and 8) are not required.
Connect the network cable in the house to your
Internet router or to your PoE switch or PoE injector
that is connected to your Internet router.
Be sure to use four insulated, shielded and twisted wires
of a network cable in accordance with the Cat.5 standard
or better.
6 (R-)
3 (R+)
2 (T-)
1 (T+)
Power supply via PoE (as an alternative)
To power the video door station via a PoE switch (e.g. D-Link DGS-1008P) or
PoE injector (e.g. TP-Link TL-PoE150S) in accordance with the PoE standard
IEEE 802.3af Mode A, the four wires bearing the numbers 1, 2, 3 and 6 of a
Cat.5 cable or better are to be used. A Cat.5 cable or better must be used as
network signals can only be transmitted over completely insulated, shielded
and twisted cables. If you use PoE as a source of power, the WiFi interface of
the video door station is automatically inactive, and the four wires for PoE
then simultaneously form the data link. The video door station won’t start
if your PoE Switch or PoE injector does not support the PoE Standard IEEE
802.3af Mode A (see Diagnostic-LED and Diagnostic-Sounds).
1. Disconnect the PoE switch or PoE injector from the power grid.
2. Place the network cable in the installation site of the video door station.
Do not combine the power supply from the power supply unit (mains adaptor)
with the power supply via PoE.
13
ENGLISHENGLISH
Electric door openers
The video door station has a zero-potential relay contact
for a standardised electric door, gate or garage opener
(two wires). There is the possibility of switching on all
electric door openers that work at a maximum power of
1A in the voltage range of up to 24V (AC/DC). The video
door station does not provide its own power supply for
the electric door opener. This is provided through the
separate power supply of the electric door opener. You can
learn more about the installation of the power supply
from the instruction manual or technical specifications of
your door opener. Should you have any questions about
this, please contact the manufacturer of your door opener.
You can find compatible electric door opener and a sample
wiring diagram at www.doorbird.com/support
Conventional electric door chime
If someone rings your video door station, you will imme-
diately receive a push notification with sound/vibration
on your smartphone or tablet. In addition the video door
station comes with a zero-potential relay contact for
connecting a conventional electric door chime inside
the building. The relay contact can be used to activate
the separate operating voltage of the door chime or the
door chime via its trigger input. If the operating voltage
of the door chime is activated, it should not be greater
than 24V (AC/DC). The power consumption should not
exceed 1A. The video door station does not provide its
own power supply for the door chime. This is provided
through the separate power supply of your conventional
door chime. Should you have any questions, please con-
tact the manufacturer of your door chime. You can find
compatible door chimes and a sample wiring diagram at
www.doorbird.com/support
Conventional door opener button
If an electric door opener is connected to the video door
station, the door opener can be opened by App and also
be directly controlled via a zero-potential button to be
found in the interior of the building, i.e. a door opening
button. In addition, the door opener button is to be
connected to the connection terminal provided. Please
make sure to add no extra voltage on that contact. You
can find compatible door opener buttons and a sample
wiring diagram on www.doorbird.com/support
Two insulated
wires.
Two insulated
wires.
Two insulated
wires.
14
STEP 6: DOWELS
If the exterior wall of the house is not made of wood, you should drill four
holes 5 mm in diameter in the wall and then place the dowels provided into
the boreholes. If the exterior wall of the house is made of wood, you will
usually not require any dowels. There are special dowels for assembling the
video door station on an insulating wall, e.g. Fischer insulating dowels. Please
check with your insulating material manufacturer regarding which dowels
they recommend.
STEP 7: ATTACH THE MOUNTING PLATE
Put the wires that you would like to connect to the video door station
through the opening in the mounting plate provided. Position the mounting
plate against the exterior wall of the house and use the screws provided to
position it in the dowels or on the wall. The mounting plate for the video
door station has been designed in such a way that it can also be installed on
uneven walls, so it is not completely flat. The partially greater clearances at
the back also serve to stabilize temperature and moisture levels.
STEP 8: PREPARING THE WIRES
Remove about 5 mm of insulation material at the end of the wires that you
would like to connect to the video door station.
STEP 9: CONNECTING THE WIRES
It is possible to connect the video door station conveniently and safely via a
connection terminal with jacks on the reverse of the video door station.
The individual contacts on the connection terminal are labelled on the reverse
of the casing. Some connectors on the connection terminal may come provided
by us with cable. Please use appropriate crimp connectors or terminal strips
to connect the supplied cables with your wires. The accompanying crimp
connectors are weatherproof and are equipped with heat-shrink tubing which
can be sealed after assembly by, for example, carefully using a heat gun.
Please remove any cables on the connection terminal that you do not need.
15
ENGLISHENGLISH
Please take care when connecting the wires. Connecting the wires the wrong
way may destroy the video door station.
CONNECTOR DESCRIPTION WIRE
T+ White and orange network cable wire
(Number 1, Transmit Data +) white-orange
T- Orange network cable wire
(Number 2, Transmit Data -) orange
R+ White and green network cable wire
(Number 3, Receive Data +) white-green
R- Green network cable wire
(Number 6, Receive Data -) green
O1 Electric door opener
(zero potential) purple
O2 Electric door opener
(zero potential) purple
C1 Electric door chime (zero potential) blue
C2 Electric door chime (zero potential) blue
B1 Door-opening button yellow
B2 Door-opening button yellow
V- Power supply, negative pole (-) black
V+ Power supply, positive pole (+) red
T+ T- R+ R- O1 O2 C1 C2 B1 B2 V- V+
max. 0-24 V DC/AC, 1 A
max. 0-24 V DC/AC, 1A
0 V, 0A
15 V DC, 1A
16
STEP 10: FINAL ASSEMBLY
Mount the video door station on the mounting plate. The video door station
will click into the locking positions intended for the mounting plate. Use the
accompanying safety screw with the appropriate tool to fix the video door
station to the underside of the mounting plate.
STEP 11: ACTIVATING THE VIDEO DOOR STATION
Switch on the power to the wires leading to the assembly location again.
You can see whether you have connected the power supply properly from the
Diagnostic LED (it lights up once the power has been connected correctly
for up to five minutes and continuously in night-vision mode). The video door
station is ready for operation (booting up process, any software updates, etc.)
once it has emitted a short diagnosis sound from the integrated loudspeaker.
This may last for up to 5 minutes. Should you not hear a beep, please check
the power supply. Please also check whether you have used a wall-plug
power-supply and not PoE and whether you have connected the positive
pole and negative pole to the video door station correctly.
STEP 12: DOWNLOADING AND INSTALLING THE APP
Download the „DoorBird“ app by Bird Home Automation onto your mobile
device from the Apple app store or Google Play store. You can always find the
most up-to-date version of the App manual on www.doorbird.com/support
If you use WiFi for connecting the video door station to your Internet router,
first go to „Settings > WiFi Setup“ and follow the instructions.
If you have finished the WiFi set-up or have connected the video door station
to your Internet router by means of a network cable, go to „Settings > Add
device“ and click on the QR code icon in the „User“ field. Scan the user QR
code found on the „Digital Passport“ that accompanies the video door station.
If you have problems adding the video door station to the App please check
if the video door station is online ( www.doorbird.com/checkonline ). If the
video door station is not online, please check the WiFi or network cable
connection again.
Since Apple uses very high quality microphones, loudspeakers and digital audio
components that are perfectly in tune with one another, the voice quality with
an iPhone or iPad is usually noticeably better than with an Android smartphone
or Android tablet.
DIAGNOSTIC-LED
This LED light is only lit up for five minutes after the video door station has
been supplied with power (and continuously at night). It lights up as soon as
the video door station is supplied with power.
Illuminated: Device is powered
17
ENGLISHENGLISH
DIAGNOSTIC-SOUNDS
After around two to five minutes, the video door station emits brief diagno-
stic sounds after it has been connected to the power grid.
1x diagnostic sound: The video door station is connected to the Internet
2x diagnostic sounds: The video door station is able to communicate with
the router, but cannot access the Internet
3x diagnostic sounds: The video door station has no connection to the network
TECHNICAL SPECIFICATIONS
GENERAL
Power supply:
15V DC (power 110-240 V AC) or
Power over Ethernet (PoE 802.3af
Mode-A)
Connectors:
Power, electric door opener/strike,
door chime, door opener button,
network
Weather-proof:
Yes, IP65
Approvals:
CE, IC, FCC, IP65
Operating conditions:
-20 to +40°C / -4 to 104°F
Humidity 10 to 85% RH
(non condensing)
Scope of delivery:
Video Door Station, mounting plate,
power supply unit (world-wide,
110-240V), DIN-rail power supply
sold separately, screw package,
quick start guide
Warranty:
see www.doorbird.com/warranty
CURRENT SYSTEM REQUIREMENTS
System requirements:
Mobile Device: Newest iOS on
iPhone/iPad, newest Android on
Smartphone/Tablet
Internet: High-Speed Landline
Broadband Internet connection, DSL,
Cable or fiber optic, no socks or Proxy
server
Network: 802.11 b/g/n 2.4GHz or
Ethernet Network, with DHCP
Recommended installation height:
Camera lens should be at a min.
height of 145 cm (57 in)
VIDEO
Camera:
HDTV 720p, dynamic (VGA – HDTV)
Lens:
High-end ultra wide-angle hemispheric
lens 180° horizontal, 90° vertical,
straightened, IR-capable
Night-vision:
Yes, light sensor, automatic IR-cut
filter, 12 IR-LEDs
18
AUDIO
Audio components:
Speaker and microphone, echo and
noise cancellation
Audio streaming:
Two-way duplex
NETWORK
WiFi:
802.11 b/g/n 2.4 GHz
Ethernet:
Connector, PoE 802.3af Mode-A
MOTION SENSOR
Type:
Passiv infrared sensor (PIR)
Detection angle:
180°
Range:
2-8 m (79-315 in)
depends on environment
INTEGRATED WIRELESS MODULES
WiFi:
2,4GHz, internal antenna
OPTIONAL ACCESSORIES
Sold separately:
see www.doorbird.com/buy
Errors and omissions excepted.
LEGAL NOTES
General remarks
1. DoorBird is a registered trademark of Bird
Home Automation GmbH.
2. Apple, the Apple logo, Mac, Mac OS,
Macintosh, iPad, Multi-Touch, iOS, iPhone
and iPod touch are trademarks of Apple Inc.
3. Google, Android and Google Play are
trademarks of Google, Inc.
4. The Bluetooth® word mark and logos are
registered trademarks of Bluetooth SIG, Inc.
5. All other company and product names may
be trademarks of the respective companies
with which they are associated.
6. We reserve the right to make changes to
our products in the interests of technical
advancement. The products shown may also
look different from the products supplied
based on ongoing enhancement.
7. Reproducing or using texts, illustrations and
photos from this instruction manual in any
media – even if only in the form of excerpts
– shall only be permitted with our express
written consent.
8. The design of this manual is subject to
copyright protection. We do not accept
any liability for any errors or any erroneous
content or printing errors (even in the case
of technical specifications or within graphics
and technical sketches).
9. Our products are in compliance with
all technical guidelines, electrical and
telecommunications regulations applicable
in Germany, the EU and the USA.
10. Our products and also the components
contained therein (ICs, software, etc.)
may only be used for civilian non-military
purposes.
Data privacy and data security
1. For maximum security, the device uses the
same encryption technologies as are used
in online banking. For your security, no port
forwarding or DynDNS is used either.
2. The data centre location for remote access
over the Internet by means of an App is
obligatory in the EU if the determined
Internet IP-Address location of the device is
within the EU. The data centre is operated
in line with the most stringent security
standards.
3. Video, audio and any other surveillance
methods can be regulated by laws that vary
from country to country. Check the laws in
your local region before installing and using
this device for surveillance purposes.
19
ENGLISHENGLISH
If the device is a door-, indoor station or camera:
In many countries video and voice signal may
only be transmitted once a visitor has rung the
bell (data privacy, configurable in the App).
Please carry out the mounting in such a
way that the detection range of the camera
limits the device exclusively to the immediate
entrance area.
The device may come with a visitor history and
motion sensor. You can activate/deactivate
this function if required.
If necessary, indicate the presence of the device
in a suitable place and in a suitable form.
Please observe any relevant country-specific
statutory regulations concerning the use of
surveillance components and surveillance
cameras applicable at the installation site.
Check with the property owner and your house
community if you are allowed to install and use
this product. Bird Home Automation GmbH
cannot be held responsible for any miss-use or
miss-configuration of this product, including
the unauthorized opening of a door.
Bird Home Automation cannot be held
responsible for damages caused by improper
existing installations or improper installation.
Software and operating system’s updates
(so-called “firmware updates”) are generally
automatically installed on the products of
Bird Home Automation GmbH via Internet,
if technically possible. Automatic firmware
updates keep the products‘ software up to
date so that they always work reliably, safely
and efficiently. Through further development,
features can be added, extended or slightly
changed. Major changes or limitations to
existing features will generally occur if Bird
Home Automation GmbH deems it necessary
(e.g. for data protection, data security or
stability reasons, or to keep them up to date).
When a firmware update is available, Bird
Home Automation GmbH‘s servers generally
automatically distribute it to all compatible
products connected to the Internet or Bird
Home Automation GmbH‘s servers. This process
is gradual and can take several weeks. As soon
as a product receives a firmware update, the
system will be installed and will restart by itself.
Installed firmware updates cannot be undone.
Since the products and software of Bird Home
Automation GmbH are not explicitly customer-
specific products, a customer cannot deny an
automatic update if the product is connected
to the Internet or to the Bird Home Automation
GmbH’s server.
Publisher
Bird Home Automation GmbH
Uhlandstraße 165
10719 Berlin
Germany
Web: www.doorbird.com
It is possible that these manual still contains
typographical errors or printing errors.The
information in this manual will be checked
regularly and corrections will be made in the
next version. We accept no liability for errors
of a technical or printing nature and their
consequences.
20
INSTALLATIONSANLEITUNG
Lesen Sie diese Anleitung sorgfältig, bevor Sie die Komponenten in Betrieb
nehmen. Bewahren Sie die Anleitung zum späteren Nachschlagen auf!
Wenn Sie das Gerät anderen Personen zur Nutzung überlassen, übergeben
Sie auch diese Bedienungsanleitung.
Die stets aktuelle Version der Installationsanleitung finden Sie unter
www.doorbird.com/de/support
Zur Vereinfachung der Begriffe verwenden wir „Gerät“ für das Produkt
„IP Video Türstation“ sowie „mobiles Endgerät“ für ein Smartphone/Tablet.
Haftung
Die Erstellung dieses Dokuments wurde sorgfältig vorbereitet. Bitte infor-
mieren Sie Bird Home Automation GmbH über etwaige Ungenauigkeiten
oder Unterlassungen. Bird Home Automation GmbH kann nicht für tech-
nische oder typografische Fehler verantwortlich gemacht werden und behält
sich das Recht vor, Änderungen an dem Produkt und den Handbüchern
ohne vorherige Ankündigung vorzunehmen. Bird Home Automation GmbH
übernimmt keinerlei Garantie in Bezug auf das in diesem Dokument ent-
haltene Material, einschließlich, aber nicht beschränkt auf die implizierten
Garantien der Marktgängigkeit und Eignung für einen bestimmten Zweck.
Bird Home Automation GmbH haftet nicht für Neben- oder Folgeschäden im
Zusammenhang mit der Bereitstellung, Durchführung oder Verwendung dieses
Materials. Das Gerät darf nur für den vorgesehenen Zweck verwendet werden.
Gerätemodifikationen
Dieses Gerät muss in Übereinstimmung mit den Anweisungen in der
Installationsanleitung installiert und verwendet werden. Dieses Gerät ent-
hält keine vom Benutzer zu wartenden Komponenten. Durch unbefugte
Gerätemodifikationen oder Änderungen erlöschen alle anwendbaren
Zertifizierungen und Zulassungen.
Verwendete Symbole
Achtung: Weist auf eine gefährliche Situation hin, die, falls
nicht verhindert, zum Tod oder schweren Verletzungen führt.
Warnung: Weist auf eine gefährliche Situation hin, welche,
falls nicht verhindert, zum Tod oder schweren Verletzungen
führen kann.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96

DoorBird D10x Guide d'installation

Taper
Guide d'installation