Krups XP100050 Manuel utilisateur

www.krups.com

XP1000

ENGLISHFRANÇAISESPAÑOL

KR_COFFEEMAKERS_ESPRESSO-XP1000_8080011304_Mise en page 1 08/06/12 10:42 Page2

2

When using electrical appliances, basic safety

precautions should always be followed to reduce the

risk of fire, electric shock, and/or injury to persons

including the following:

1. Read all instructions prior to first use.

2. Do not touch hot surfaces. Always use handles or

knobs.

3. To protect against fire, electric shock and injury to

persons, do not immerse cord, plugs or machine in

water or other liquid.

4. Not intented for use by children.

5. Close supervision is necessary when any machine is

used near children. Keep machine out of reach of

children.

6. This appliance is not designed to be used by children

or people without knowledge or experience with the

machine.

7. Children must be supervised to ensure that they do

not play with the appliance.

8. Burns can occur from touching the hot plate, hot water

or steam. Exercise caution.

9. Exercise caution when using the steam nozzle as

steam can cause scalding.

IMPORTANT

SAFEGUARDS

KR_COFFEEMAKERS_ESPRESSO-XP1000_8080011304_Mise en page 1 18/06/12 09:45 Page2

ENGLISH

3

10. Unplug machine from outlet when not in use and when

cleaning. Allow to cool before putting on or taking off

parts, before cleaning the machine, and before storing.

11. All machines are subject to stringent quality control.

Practical tests using machines taken at random are

conducted and this may explain any slight marks or

coffee residue prior to use.

12. Do not operate any machine with a damaged cord or

plug or after the machine malfunctions, or has been

damaged in any manner. Return machine to the

nearest Krups Service Center for examination, repair

or adjustment or your respective countries Consumer

Service Department.

13. To reduce the risk of injury do not drape cord over the

counter top or table top where it can be pulled on by

children or tripped over accidentally.

14. Do not let cord hang over edge of table or counter, or

touch hot surfaces.

15. The use of accessory attachments not recommended

by Krups may result in fire, electric shock or injury to

persons.

16. Do not use outdoors.

17. Do not place on or near a hot gas or electric burner, or

in a heated oven.

18. To disconnect the machine, turn the control to “off”

then remove plug from wall outlet. Do not yank cord,

instead grasp plug and pull to disconnect.

KR_COFFEEMAKERS_ESPRESSO-XP1000_8080011304_Mise en page 1 18/06/12 09:45 Page3

4

19. Do not use the machine for anything other than its

intended use.

20. Do not pour liquids other than water and descaling

solutions specified in this manual into the water tank.

21. Protect the machine against humidity and freezing.

22. Scalding may occur if the lid is removed during the

brewing cycles.

23. This machine is for household use only.

SAVE THESE

INSTRUCTIONS

CAUTION

This machine is intended for household use only. Any

servicing other than cleaning and user maintenance

should be performed by the nearest authorized Krups

Service Center.

Visit our website at www.krupsusa.com in the USA or

www.krups.ca in Canada or contact your respective

country's Consumer Service department for the service

center nearest to you.

To reduce the risk of fire or electric shock, do not attempt

to disassemble the machine. Repair should be done by an

authorized Krups Service Center only.

KR_COFFEEMAKERS_ESPRESSO-XP1000_8080011304_Mise en page 1 18/06/12 09:45 Page4

5

ENGLISH

A short power-supply cord is to be provided to reduce risks

resulting from becoming entangled in or tripping over a longer cord.

A. We do not recommend using an extension cord with this

device.

B. If an extension cord is absolutely necessary,

1) the marked electrical rating of the extension cord

should be at least as great as the electrical rating of

the machine,

2) the longer cord should be arranged so that it will not

drape over the counter top or table top where it can

be pulled on by children or tripped over.

C. This machine has a polarized plug (one blade is wider

than the other). To reduce the risk of electric shock, this

plug is intended to fit into a polarized outlet only one way.

If the plug does not fit fully into the outlet, reverse the

plug. If it still does not fit, contact a qualified electrician.

Do not attempt to modify the plug in any way.

In the interest of improving products, Krups reserves the right to

change specifications without prior notice.

SHORT CORD INSTRUCTIONS

KR_COFFEEMAKERS_ESPRESSO-XP1000_8080011304_Mise en page 1 18/06/12 09:45 Page5

i

b

b3

b1

b2

bc

g

h

f

e

d

c1

c2

a

c

6

KR_COFFEEMAKERS_ESPRESSO-XP1000_8080011304_Mise en page 1 18/06/12 09:45 Page6

1 2

3 4

5 6

7

ENGLISH

KR_COFFEEMAKERS_ESPRESSO-XP1000_8080011304_Mise en page 1 18/06/12 09:45 Page7

7 8

9 10

11

8

KR_COFFEEMAKERS_ESPRESSO-XP1000_8080011304_Mise en page 1 18/06/12 09:45 Page8

9

ENGLISH

Espresso is a richer and more aromatic brew than regular coffee.

It is typically enjoyed in smaller quantities because of its richness,

and for that reason, espresso is usually served in small (1.5 - 2

oz) cups.

Your appliance when properly used will produce espresso that is

deep in flavor and dark in color. Just follow the instructions and

use fresh roasted coffee that has been pre-ground to an espresso

grind.

Preparing an espresso or cappuccino is different from brewing

regular drip coffee. One main difference is that the water will

come to a boil and will then be forced through the ground coffee.

This means that an espresso machine works under pressure and

needs special attention.

DESCRIPTION

a

ON/OFF Pilot light

b

Selector knob

b1

Off position

b2

Espresso-coffee making

position

b3

Hot steam position

c

Filter-holder

c1

Removable filter for 1

to 4 cups

c2

Filter locker

d

Measuring spoon

e

Carafe

f

Removable drip tray grid

g

Cappuccino accessory

h

Steam nozzle

i

Boiler cap for water tank

AUTHENTIC ESPRESSO

KR_COFFEEMAKERS_ESPRESSO-XP1000_8080011304_Mise en page 1 18/06/12 09:45 Page9

10

CAUTION – PRESSURE

Never open boiler cap (i) or remove filter holder (c) while your

appliance is turned “on” or while there is still pressure in the

boiler container.

To check for pressure:

Turn the selector knob (b) to the “Off” position. Fig. 1.

Turn the selector knob to the steam position (b3) Fig. 10. If steam

comes out of the nozzle, then the boiler chamber is still under

pressure. Close steam knob and proceed with instructions listed

below.

Take a pitcher filled with cold water and hold it underneath the

steam nozzle with nozzle inserted into the pitcher. Then turn the

selector knob to the steam position (b3). Leave steam release

knob open until no more steam comes out of nozzle. When

finished turn the selector knob (b) to the “Off” position.

Now you can remove the boiler cap and the filter holder.

CAUTION – HOT

Do not touch boiler cap (i) during operation. Before removing

boiler cap turn off machine, let it cool down for at least 2 or

3 minutes. Relieve pressure. (See CAUTION-PRESSURE).

Important! Before using your machine for the first time, or after

not having used it for a considerable amont of time, rinse the

appliance as indicated below. Check that the appliance is

unplugged.

Check that the appliance is unplugged.

Unscrew the boiler cap. Fig. 2.

Pour 8 oz (240 ml) of cold water into the water tank. Do not pour

warm or hot water into the water tank. Fig. 3.

Screw the boiler cap on tightly. Fig. 4.

Fit the filter (without any coffee) into the filter-holder and rotate

filter inside filter-holder to secure it. Fig. 5.

BEFORE FIRST USE

KR_COFFEEMAKERS_ESPRESSO-XP1000_8080011304_Mise en page 1 18/06/12 09:45 Page10

11

Insert the filter holder in the appliance. Turn it firmly from left to

right to put it into the “locked” position. Fig. 6.

Place the carafe or a cup under the filter holder. Plug in the

appliance. Fig. 7.

Turn the selector knob to the “Espresso” position (b2). Fig. 8.

The ON/OFF pilot light will light up.

After a few minutes, the water will boil and hot water will start to

drip. When the container/cup is full, turn the selector knob to the

“Off” position (b1).

Place a cup under the steam nozzle and turn the selector knob

to the steam setting (b3). When there is no more steam, turn to

the “Off” position (b1).

Never remove filter holder or open boiler cap without having

released remaining pressure in appliance. (See CAUTION-

PRESSURE).

Important! Check that the appliance is unplugged and that

there is no pressure. (See CAUTION-PRESSURE).

Unscrew the boiler cap Fig. 2. Measure out the right amount of

water for your needs and pour it into the water tank. For instance:

an espresso-sized cup (small cup for strong espresso) = 1 to 2

oz (25 to 50 ml). A standard-sized cup (for milder espresso) = 3

to 4 oz (75 to 100 ml). Up to 4 espressos or 2 standard cups can

be made at one time, without adding additional water to the tank.

Pour the water into the tank. Fig. 3.

Screw the boiler cap on tightly. Fig. 4.

Plug in the appliance.

Fit the filter into the filter-holder and rotate filter inside filter-holder

to secure it. Fig. 5.

Put the ground coffee into the filter holder using the measuring

spoon. 1 full measuring spoon is the amount needed for 1

MAKING ESPRESSO

ENGLISH

KR_COFFEEMAKERS_ESPRESSO-XP1000_8080011304_Mise en page 1 18/06/12 09:45 Page11

12

espresso. Using a tamper or the back of the measuring spoon

tamp down the coffee.

Remove any excess coffee on the edge of the filter-holder.

ATTENTION! Do not over fill or pack coffee too tightly.

Fit the filter-holder into the appliance turning it from left to right

and locking it firmly into place. Fig. 6.

Place a cup or the carafe under the filter-holder. Fig. 7.

Turn the selector knob to “espresso” (b2). Fig. 8.

The ON/OFF pilot light will light up. After 3 to 4 minutes, the

espresso will start to drip. Wait until the espresso has stopped

dripping before removing the cup or carafe and then turn the

selector knob to the “Off” position (b1). Fig. 9.

ATTENTION! We advise you to not switch off the appliance

before the cycle is completely finished. At the end of the

cycle, steam will dry out the coffee grounds thus producing a

puck that is drier and easier to remove. Never remove filter

holder or open the water tank without having released

remaining pressure in appliance. (See CAUTION-PRESSURE).

Once you have removed the pressure from the machine the

filter holder can be removed. To throw away the coffee

grounds, turn over the filter holder and shake it to make the

coffee grounds fall out.

Follow the instructions for “Making Espresso” but add 2 oz (50

ml) of water to the volumes indicated.

An authentic cappuccino is made using 1/3 espresso, 1/3 hot

steamed milk and 1/3 frothed milk. We recommend frothing the

milk before making the coffee.

Pour 4 to 6 oz (100 to 150 ml) of fresh, cold milk into a small

pitcher. Do not use a pitcher cleaned with hot water or one that is

still warm.

MAKING CAPPUCCINOS

KR_COFFEEMAKERS_ESPRESSO-XP1000_8080011304_Mise en page 1 18/06/12 09:45 Page12

13

The milk will froth better in a cold pitcher. The pitcher should fit

underneath the cappuccino nozzle. We recommend using 1 or

2% milk for a stiff, dense froth. Use whole milk if you prefer a

creamy froth.

Turn the knob to the “Steam” position (b3). Fig. 10.

When the steam starts coming out of the nozzle, immerse the

nozzle in the pitcher of milk and make circular movements going

up and down to froth the milk. It is important not to have the

nozzle touch the bottom of your pitcher. Fig. 11.

Once the milk is frothed, put a cup underneath the filter holder.

Turn the knob to the “Espresso” position (b2). Fig. 8.

Once the espresso has finished dripping, spoon the frothy milk

over the espresso to finish the cappuccino. Never remove filter

holder or open boiler cap without having released remaining

pressure. (See CAUTION-PRESSURE).

ATTENTION! Clogged Steam nozzle:

Milk residue will build up in the tip of the steam nozzle after

frothing milk. To avoid clogging, remove the plastic housing of

the cappuccino nozzle once the appliance has cooled, for easy

cleaning. Then follow “cleaning the steam nozzle” as described

in the section “Cleaning the Cappuccino Nozzle”.

Don’t forget to replace the tip of the nozzle and screw it on tightly.

Follow the instructions for “Making Cappuccinos” with the

following proportions: 2/3 frothy milk, 1/3 espresso, and if desired

you may spoon some milk foam on top.

Steam is used to froth milk and also to reheat water (tea, hot

drinks).

MAKING CAFFE LATTES

STEAMING WITHOUT MAKING ESPRESSO

ENGLISH

KR_COFFEEMAKERS_ESPRESSO-XP1000_8080011304_Mise en page 1 18/06/12 09:45 Page13

14

Check that the appliance is unplugged and that there is no

contained pressure. (See CAUTION-PRESSURE).

Measure out a small amount of water and pour into tank. For

example: 2 oz (50 ml) of water to heat 4 oz (100 ml) of liquid.

Important: for maximum efficiency, avoid putting more than

4 oz (100 ml) of water into the tank.

Tightly screw on the boiler cap. Fig. 4.

Plug in the appliance.

Immerse the steam nozzle in the liquid to be heated.

Turn the knob to “steam” (b3). Fig. 10.

The ON/OFF pilot light will light up.

Steam is produced after 2 to 3 minutes of preheating.

Once the liquid is hot, turn selector knob back to “Off” (b1) and

unplug the appliance.

If you do not need all the water for steaming, proceed as follows:

Turn off the machine.

Release the remaining steam pressure into another container.

Before turning the knob again, turn the knob to “steam” (b3) to

remove any steam, take care to put a cup underneath the steam

nozzle.

CAUTION! Do not turn the selector knob back to "Off" (b1)

before all steam is released! (See CAUTION - PRESSURE).

ATTENTION! The plastic housing of the cappuccino nozzle

(g) has 2 fine holes at the top which draw air into the milk.

If those holes get clogged, the milk will not be frothed

properly. Therefore, do not dip the cappuccino nozzle in milk

or froth up to those holes.

ATTENTION! Immediately after use, wash the steam nozzle

with a damp sponge.

KR_COFFEEMAKERS_ESPRESSO-XP1000_8080011304_Mise en page 1 18/06/12 09:45 Page14

15

Unplug the appliance and let it cool down completely before you

clean it.

Occasionally wipe the outside of the appliance with a damp

cloth. Regularly wash and dry the drip tray and its grid.

Do not use alcohol-based or abrasive cleaning products or

solvents.

Regularly clean the grid through which the hot water passes with

a damp sponge.

Important: Never use soap or other cleaning agents as it will

impact the taste of your beverages.

Clean the steam nozzle each time after you have immersed it in

the milk, otherwise the inside of the nozzle can become clogged

and the milk deposits on the outside will harden and become

difficult to remove.

If clogging does occur, remove the plastic housing of the

cappuccino nozzle (g) once the appliance has cooled and then

unscrew the tip of the steam nozzle.

Remove all milk particles by using a clean sewing needle and

rinse under the faucet. Replace nozzle tip making sure to screw

it on tightly. Wipe off the outside of the nozzle with a wet cloth.

The plastic housing of the cappuccino nozzle should be rinsed

in warm water. If the small suction openings are clogged up, they

can be opened with a small needle.

CAUTION! Do not try to open or disassemble the main body

of the machine.

CLEANING AND SERVICING

CLEANING THE CAPPUCCINO NOZZLE

ENGLISH

KR_COFFEEMAKERS_ESPRESSO-XP1000_8080011304_Mise en page 1 18/06/12 09:45 Page15

16

The warranty does not cover a faulty or broken espresso

machine due to not being descaled.

Due to the acidity of the cleaning solution, we recommend

protecting your worktop and sink during the descaling process,

especially if it is made of marble or stone. Isolate your appliance

with an old towel, tablecloth or tray.

The espresso machine must be decalcified regularly. The

frequency depends on the hardness of your water and how often

you use the espresso machine.

Before descaling, the brewing sieve on the brewing head must

first be screwed off.

1. Remove all lime and coffee residues from the brewing sieve

and the brewing head.

2. Remove the plastic housing of the cappuccino nozzle (g).

As a descaling agent we recommend the use of Krups descaling

solution F054 available at authorized Krups retailers and Service

Centres or by contacting your respective countries Customer

Service Department.

3. Dissolve a packet of KRUPS descaling solution in 10 oz/300

ml of lukewarm water and pour into the boiler container and

screw back the cap. Put a container under the brewing head

and another under the steam nozzle.

(Note: Do not secure the filter holder (c) during decalcification).

4. Open the steam valve and turn on the appliance. Allow the

descaling solution to run out of the espresso outlet and the

steam nozzle.

5. After each brewing cycle, switch off the appliance and allow

the appliance to cool down.

6. Repeat this operation once more.

Following this, allow 2 containers of clear water to run through

the system. Switch off the appliance. Allow the appliance to cool

down. Insert the brewing sieve into the brewing head again and

push the plastic housing of the cappuccino nozzle onto the

steam nozzle.

DECALCIFYING THE ESPRESSO SIDE

KR_COFFEEMAKERS_ESPRESSO-XP1000_8080011304_Mise en page 1 18/06/12 09:45 Page16

17

TROUBLESHOOTING

Problems Probable Causes Solutions

Espresso

The coffee drips

too slowly.

The coffee is ground

too fine.

Filter blocked.

Water passage grid is

clogged.

Presence of scale.

Use more coarsely

ground coffee.

Clean it with a brush.

Clean the appliance

when cold.

De-Scale the

appliance.

The coffee drips

too slowly.

Dirty filter-holder or

dirty filter.

The coffee is ground

too fine.

Clean them with hot

water.

Use more coarsely

ground coffee.

The coffee

doesn’t drip.

The knob is in the

“Steam” position

(b3).

Turn the knob to the

“Espresso” position

(b2).

The espresso

leaks onto the

filter holder sides.

Filter holder is

clogged up.

The filter holder is not

properly positioned.

Remove any excess

ground coffee.

Put it back into place

and lock it into

position.

Bad taste. Insufficient rinsing. Follow the rinsing

instructions.

Steam

Water runs out of

the filter holder.

The knob is in the

“Espresso”

position (b2).

Turn the knob to the

“Steam” position (b3).

Little or no steam

in the “steam”

position.

The knob opened too

early.

Close the “Steam”

knob for 2

minutes.

ENGLISH

KR_COFFEEMAKERS_ESPRESSO-XP1000_8080011304_Mise en page 1 18/06/12 09:45 Page17

18

: www.krups.com

With a strong commitment to the environment, most of Krups

products are repairable during and after the warranty period.

Before returning any defective products to the point of

purchase, please call Krups consumer service directly at the

phone number below for repair options. Your help to sustain

the environment is appreciated!

The Warranty

This product is guaranteed by Krups for a period of 2 years against

any manufacturing defect in materials or workmanship, starting

from the initial date of purchase.

The manufacturer's warranty by Krups is an extra benefit which

does not affect consumer's Statutory Rights.

The Krups warranty covers all costs related to restoring the proven

defective product so that it conforms to its original specifications,

through the repair or replacement of any defective part and the ne-

cessary labor. At Krups’s choice, a replacement product may be

provided instead of repairing a defective product. Krups’s sole obli-

gation and your exclusive resolution under this warranty are limited

to such repair or replacement.

Problems Probable Causes Solutions

The steam nozzle

doesn’t froth the

milk.

Blocked steam

nozzle.

Whole milk used.

Milk not fresh or cold

enough.

Container doesn’t

have the right shape.

Rinse out the steam

nozzle.

Use 1 or 2% milk.

Always use very fresh,

cold milk.

Use a small diameter

container (small jug).

LIMITED WARRANTY

KR_COFFEEMAKERS_ESPRESSO-XP1000_8080011304_Mise en page 1 18/06/12 09:45 Page18

19

Conditions & Exclusions

The Krups warranty only applies within USA, Canada & Mexico,

and is valid only on presentation of a proof of purchase. The pro-

duct can be taken directly in person to an authorized

service centre or must be adequately packaged and returned, by

recorded delivery (or equivalent method of postage), to a Krups au-

thorized service centre. Full address details for each country’s au-

thorized service centre are listed on the Krups website

(www.krups.com) or by calling the appropriate telephone number

listed below to request the appropriate postal address.

Krups shall not be obliged to repair or replace any product which

is not accompanied by a valid proof of purchase.

This warranty will not cover any damage which could occur as a

result of misuse, negligence, failure to follow Krups instructions,

use on current or voltage other than as stamped on the product,

or a modification or unauthorized repair of the product. It also does

not cover normal tear and wear, maintenance or replacement of

consumable parts, and the following:

- using the wrong type of water

- scaling (any de-scaling must be carried out according to the

instructions for use);

- ingress of water, dust or insects into the product;

- mechanical damages, overloading

- damages or bad results due to wrong voltage or frequency

- accidents including fire, flood, lightning, etc

- professional or commercial use

- damage to any glass or porcelain ware in the product

This warranty does not apply to any product that has been tampe-

red with, or to damages incurred through improper use and care,

faulty packaging by the owner or mishandling by any carrier.

The Krups manufacturer's warranty applies only for products pur-

chased and used in USA, Canada & Mexico. Where a product pur-

chased in one country and then used in another one:

a) The Krups guarantee duration is the one in the country of

usage of the product, even if the product was purchased in

another listed country with different guarantee duration.

ENGLISH

KR_COFFEEMAKERS_ESPRESSO-XP1000_8080011304_Mise en page 1 18/06/12 09:45 Page19

20

b) The Krups guarantee does not apply in case of non confor-

mity of the purchased product with the local standards, such

as voltage, frequency, power plugs, or other local technical

specifications

c) The repair process for products purchased outside the coun-

try of use may require a longer time if the product is not locally

sold by Krups

d) In cases where the product is not repairable in the new coun-

try, the Krups guarantee is limited to a replacement by a si-

milar product or an alternative product at similar cost, where

possible.

Consumer Statutory Rights

This Krups manufacturer's warranty does not affect the statutory

rights a consumer may have or those rights that cannot be excluded

or limited, nor rights against the retailer from which the consumer

purchased the product. This warranty gives a consumer specific

legal rights, and the consumer may also have other legal rights

which vary from State to State or Country to Country or Province to

Province. The consumer may assert any such rights at his sole dis-

cretion.

Additional information

Accessories, Consumables and end-user replaceable parts can be

purchased, if locally available, as described in Krups internet site.

: www.krups.com

CANADA

GROUPE SEB

CANADA

345 Passmore

Avenue

Toronto, ON

M1V 3N8

MEXICO

Groupe SEB

MEXICO

S.A. de C.V.

Goldsmith 38 Desp.

401 Col. Polanco

Delegacion Miguel

Hildalgo

11 560 Mexico D.F.

MEXICO

U.S.A.

GROUPE SEB

USA

2121 Eden

Road

Millville, NJ

08332

1-800-418-3325

01800 1128325

800-526-5377

KR_COFFEEMAKERS_ESPRESSO-XP1000_8080011304_Mise en page 1 18/06/12 09:45 Page20

La page charge ...

Krups XP100050 Manuel utilisateur

Krups XP100050 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents