Briteq BTX-FALCON Le manuel du propriétaire

Catégorie
Projecteurs
Taper
Le manuel du propriétaire
ENGLISH OPERATION MANUAL
BRITEQ
®
1/79 BTX-FALCON
OPERATION MANUAL
Thank you for buying this BRITEQ product. To take full advantage of all possibilities and for your own safety,
please read these operating instructions very carefully before you start using this unit.
FEATURES
This unit is radio-interference suppressed. This product meets the requirements of the current European and
national guidelines. Conformity has been established and the relevant statements and documents have been
deposited by the manufacturer.
A very bright moving head projector based on a brand-new powerful 180W LED engine!
100% backward compatible with our famous BTX-180LS but with over 40% more lumen output !
The use of advanced 16° optics guarantees an incredibly bright output: 221’700 lux @ 1m
Perfect for rental companies, stage, discotheques, …
The very fast pan/tilt movements (540°/270°) assure very dynamic show programming.
8 or 16bit resolution pan/tilt resolution with X/Y position correction and pan/tilt speed channel.
Uses 17 DMX channels for an excellent range of possibilities and specs:
DMX-controlled electronic focus
DMX-controlled iris
2 gobo wheels for nice gobo overlay effects:
7 fast rotating gobos + open
8 fixed gobos + open
2 color wheels, each with 7 carefully selected dichroic colors + open
Extremely fast electronic dimmer/shutter
Fast rotating 3facet prism for special effects
Different strobe effects
Effect channel: remote lamp on/off control, different blackout functions, etc.
Works also in standalone & master/slave mode: the internal mic triggers the preprogrammed shows.
Neutrik PowerCON
®
in/outputs: easy daisy chaining of several units up to 16A.
Neutrik 3pin & 5pin in/outputs for maximum flexibility in a professional environment
Easy firmware updates keep your machine up-to-date at all times (optional firmware updater needed)
The matrix LCD-display assures easy navigation in the different setup menus
High efficiency and low power consumption, only 245W
Equipped with omega brackets for fast installation
BEFORE USE
Before you start using this unit, please check if there’s no transportation damage. Should there be any, do
not use the device and consult your dealer first.
Important: This device left our factory in perfect condition and well packaged. It is absolutely necessary
for the user to strictly follow the safety instructions and warnings in this user manual. Any damage caused
by mishandling is not subject to warranty. The dealer will not accept responsibility for any resulting defects
or problems caused by disregarding this user manual.
Keep this booklet in a safe place for future consultation. If you sell the fixture, be sure to add this user
manual.
Check the contents:
Check that the carton contains the following items:
Operating instructions
BTX-FALCON projector
2pcs Quick lock “Omega bracket
PowerCON
®
cable
ENGLISH OPERATION MANUAL
BRITEQ
®
2/79 BTX-FALCON
SAFETY INSTRUCTIONS:
To protect the environment, please try to recycle the packing material as much as possible.
To prevent fire or shock hazard, do not expose this appliance to rain or moisture.
To avoid condensation to be formed inside, allow the unit to adapt to the surrounding temperatures when
bringing it into a warm room after transport. Condense sometimes prevents the unit from working at full
performance or may even cause damages.
This unit is for indoor use only.
Don’t place metal objects or spill liquid inside the unit. Electric shock or malfunction may result. If a foreign
object enters the unit, immediately disconnect the mains power.
Locate the fixture in a well ventilated spot, away from any flammable materials and/or liquids. The fixture
must be fixed at least 50cm from surrounding walls.
Don’t cover any ventilation openings as this may result in overheating.
Prevent use in dusty environments and clean the unit regularly.
Keep the unit away from children.
Inexperienced persons should not operate this device.
Maximum safe ambient temperature is 40°C. Don’t use this unit at higher ambient temperatures.
Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging
and servicing.
Allow the device about 10 minutes to cool down before to start servicing.
Always unplug the unit when it is not used for a longer time or before to start servicing.
The electrical installation should be carried out by qualified personal only, according to the regulations for
electrical and mechanical safety in your country.
Check that the available voltage is not higher than the one stated on the unit.
The power cord should always be in perfect condition. Switch the unit immediately off when the power cord
is squashed or damaged. It must be replaced by the manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
Never let the power-cord come into contact with other cables!
This fixture must be earthed in order to comply with safety regulations.
Don’t connect the unit to any dimmer pack.
Always use an appropriate and certified safety cable when installing the unit.
In order to prevent electric shock, do not open the cover. There are no user serviceable parts inside.
Never repair a fuse or bypass the fuse holder. Always replace a damaged fuse with a fuse of the same
type and electrical specifications!
In the event of serious operating problems, stop using the fixture and contact your dealer immediately.
The housing and the lenses must be replaced if they are visibly damaged.
Please use the original packing when the device is to be transported.
CAUTION: To reduce the risk of electric shock, do not remove
the top cover. No user-serviceable parts inside. Refer servicing
to qualified service personnel only.
The lightning flash with arrowhead symbol within the equilateral triangle is intended to alert the
use or the presence of un-insulated “dangerous voltage” within the product’s enclosure that may
be of sufficient magnitude to constitute a risk of electric shock.
The exclamation point within the equilateral triangle is intended to alert the user to the presence
of important operation and maintenance (servicing) instructions in the literature accompanying
this appliance.
This symbol means: indoor use only
This symbol means: Read instructions
This symbol determines: the minimum distance from lighted objects. The minimum distance
between light-output and the illuminated surface must be more than 2 meters
The device is not suitable for direct mounting on normally flammable surfaces. (suitable only for
mounting on non-combustible surfaces)
CAUTION: Do not stare at operating lamp.
May be harmful to the eyes.
ENGLISH OPERATION MANUAL
BRITEQ
®
3/79 BTX-FALCON
Due to safety reasons it is prohibited to make unauthorized modifications to the unit.
Important: Never look directly into the light source! Don’t use the effect in the presence of persons suffering
from epilepsy.
DESCRIPTION:
CONTROL PANEL:
1. STATUS LEDS: leds used to indicate the status of the projector.
DMX
DMX input present, blinks during a software update
MASTER
Projector works in master mode
SLAVE
Projector works in slave mode
SOUND
Shows audio activity
2. DISPLAY shows the various menus and the selected functions.
3. NAVIGATION BUTTONS:
MENU
To enter the setup menu or return to a previous function
DOWN
To go forward in the menu tree
UP
To go backward in the menu tree
ENTER
To confirm the selected function
Two button shortcuts make life easier for the installer:
Press UP & DOWN buttons together: Display turns over 180°
Press MENU + ENTER buttons for 3sec: the projector resets.
4. OMEGA CLAMP: on the bottom you can insert the included “omega” quick clamp. Just turn the locking
system over 90° to secure the clamp. Always use a safety cable for extra security!
5. DMX IN/OUTPUTS: used for DMX512 linking, you can use good quality balanced signal cables with 3pin
or 5pin XLR-connectors.
6. MAINS FUSE: this fuse only protects the electronics of the projector, mains input/output (7) is not fused.
7. MAINS INPUT / OUTPUT: with PowerCON
®
sockets, connect the supplied mains cable here, you can
daisy chain several units, up to max 16A. Input and output are connected to each other without any fuse.
Hint: Please check our website for special cable assemblies that contain both power (3x1.5mm² with Neutrik
PowerCON
®
) and balanced signal (XLR 3pin) in one cable. Different lengths are available: 1.3m, 3m, 5m and
10m, very convenient!
ENGLISH OPERATION MANUAL
BRITEQ
®
4/79 BTX-FALCON
SETUP MENU:
Press the MENU button to enter the setup menu.
Use UP / DOWN buttons to browse the submenu(s) and/or select functions, change the value(s).
Always press the ENTER button to confirm.
To return to a previous menu, always use the MENU button.
Note 1: After 60 seconds the display will automatically return to normal mode without any change.
Note 2: The grey colored options in the setup menu are the default settings.
DMX Functions
This submenu contains all DMX-related settings.
Press the MENU button and select the DMX Functions” submenu.
DMX Address
Used to set the starting address in a DMX
setup.
Select DMX address and press ENTER.
Use DOWN / UP buttons to change the
DMX512 address.
Press the ENTER button to save.
To return to a previous menu, press the MENU
button.
DMX Channel Mode
Used to select the desired channel mode.
Select DMX Channel Mode and press
ENTER
Use DOWN / UP buttons to select the desired
DMX channel mode.
Press the ENTER button to save.
To return to a previous menu, press the MENU
button.
View DMX Value
Select View DMX Value and press ENTER.
The display now shows the DMX-values for the
different channels.
To return to a previous menu, press the MENU
button or after 60 seconds the display will
automatically return to normal mode.
Show Settings
This submenu contains specific settings for
when the projector is used in standalone or
master/slave mode (without DMX controller).
Press the MENU button and select the Show
Settings” submenu.
Offline Mode
Determines how the projector should behave
when the DMX-signal is lost or not connected
(so it is “offline”).
M/S mode (master/slave mode): when no
DMX-signal is detected, the projector starts
working in standalone mode. The internal
programs will be triggered to the rhythm of the
music by the built-in microphone.
Hold mode: when no DMX-signal is detected,
the unit freezes with the latest dmx values
received and waits for the DMX-signal.
ENGLISH OPERATION MANUAL
BRITEQ
®
5/79 BTX-FALCON
Blackout mode: when no DMX-signal is detected, the unit goes in blackout and waits for the DMX-signal.
Select “Offline Mode” and press ENTER
Use DOWN / UP buttons to select one of the available options.
Press the ENTER button to save.
To return to a previous menu, press the MENU button.
Show Mode
Used to choose the Show mode when used in standalone or master/slave mode.
Select “Show Mode” and press ENTER
Use DOWN / UP buttons to select one of the available Shows.
Press the ENTER button to save.
To return to a previous menu, press the MENU button.
Slave Mode
Used to make the slave unit work in opposite to the master or to work in complete sync.
Select “Slave Mode” and press ENTER
Use DOWN / UP buttons to select one of the available options:
Slave1: the slave follows the master in complete sync
Slave2: the slave follows the master in opposite sync
Press the ENTER button to save.
To return to a previous menu, press the MENU button.
Focus 1
Used to help you adjusting the focus of the rotating gobos (gobo wheel 1) while used in standalone
mode.
Select Focus 1 and press ENTER: the projector shows one of the rotating gobos so you can easily
adjust the focus.
Use DOWN / UP buttons until the gobo is sharp (value range: 0-255)
Press the ENTER button to save.
To return to a previous menu, press the MENU button.
Remark: please note that you can only set an “average focus” , while in standalone mode it is not possible to
set the focus perfectly sharp for all directions.
Focus 2
Used to help you adjusting the focus of the fixed gobos (gobo wheel 2) while used in standalone
mode.
Select Focus 2and press ENTER: the projector shows one of the fixed gobos so you can easily adjust
the focus.
Use DOWN / UP buttons until the gobo is sharp (value range: 0-255)
Press the ENTER button to save.
To return to a previous menu, press the MENU button.
Remark: please note that you can only set an “average focus” , while in standalone mode it is not possible to
set the focus perfectly sharp for all directions.
Sound Trigger
If switch on, the unit works to rhythm of the beat while used in standalone or master/slave mode
Select “Sound Trigger” and press ENTER
Use DOWN / UP buttons to select:
On: internal shows triggered by the internal microphone
Off: internal shows triggered at a preset slow speed.
Press the ENTER button to save.
To return to a previous menu, press the MENU button.
Sound Sensitivity
Used to set the sensitivity of the internal microphone while used in standalone or master/slave mode
Select “Sound Sensitivity” and press ENTER
Use DOWN / UP buttons to change the sensitivity from 0 (very low sensitivity) to 100 (high sensitivity).
Press the ENTER button to save.
To return to a previous menu, press the MENU button.
ENGLISH OPERATION MANUAL
BRITEQ
®
6/79 BTX-FALCON
Fixture Settings
This submenu contains specific fixture settings.
Press the MENU button and select the Fixture Settings” submenu.
Pan Inverse
No: Panning movement is not inverted.
Yes: Panning movement is inverted.
Select Pan Inverseand press ENTER
Use DOWN / UP buttons to select Yes or No.
Press the ENTER button to save.
To return to a previous menu, press the MENU button.
Tilt Inverse
No: Tilt movement is not inverted.
Yes: Tilt movement is inverted.
Select “Tilt Inverse” and press ENTER
Use DOWN / UP buttons to select Yes or No.
Press the ENTER button to save.
To return to a previous menu, press the MENU button.
P/T Feedback
While touching the head of the projector, the pan/tilt positioning can be disturbed and not in sync with the
other machines. P/T Feedback can automatically correct such issues.
Select “P/T Feedback” and press ENTER
Use DOWN / UP buttons to select:
No: Pan/Tilt are not automatically corrected.
Yes: Pan/Tilt are automatically corrected.
Press the ENTER button to save.
To return to a previous menu, press the MENU button.
Iris Inverse
Used to determine the iris behavior.
Select “Iris Inverse and press ENTER
Use DOWN / UP buttons to select:
No: Iris is open while DMX-value is 000.
Yes: Iris is open while DMX-value is 255.
Press the ENTER button to save.
To return to a previous menu, press the MENU button.
Bl.O. P/T Moving
“Blackout while Pan/tilt are moving”: while pan/tilt positions are changing the projector can cut off the
output to obtain a special effect.
Select “Bl.O. P/T Moving” and press ENTER
Use DOWN / UP buttons to select:
No: output stays on during pan/tilt movements.
Yes: output shuts off during pan/tilt movements.
Press the ENTER button to save.
To return to a previous menu, press the MENU button.
Bl.O. Color Change
“Blackout while changing the colors”: while colors are changing the projector can cut off the output to
obtain a special effect.
Select “Bl.O. Color Change” and press ENTER
Use DOWN / UP buttons to select:
No: output stays on during color changes.
Yes: output shuts off during color changes.
Press the ENTER button to save.
To return to a previous menu, press the MENU button.
ENGLISH OPERATION MANUAL
BRITEQ
®
7/79 BTX-FALCON
Bl.O. Gobo Change
“Blackout while changing the gobos”: while gobos are changing the projector can cut off the output to
obtain a special effect.
Select “Bl.O. Gobo Change” and press ENTER
Use DOWN / UP buttons to select:
No: output stays on during gobo changes.
Yes: output shuts off during gobo changes.
Press the ENTER button to save.
To return to a previous menu, press the MENU button.
Brightness Cali
Although the BTX-FALCON is 100% backward compatible with the previous BTX-180LS, the new
LED-engine in the BTX-FALCON has about 40% more output. With this function you can match
(reduce) the light output with that of the BTX-180LS.
Select “Brightness Cali” and press ENTER
Use DOWN / UP buttons to change the light output from 50% to 100%.
(a value of about 60% will match with the BTX-180LS)
Press the ENTER button to save.
To return to a previous menu, press the MENU button.
Display Settings
This submenu contains display related settings
Press the MENU button and select the Display Settings” submenu.
Display Inverse
The projector can be fixed/used in upward position
or hung in upside-down position. To make reading
of the display easier, you can turn it over 180°.
No: Display readable while the projector is in
upward position.
Yes: Display readable while the projector is in
upside-down position.
Select “Display Inverse” and press ENTER
Use DOWN / UP buttons to select Yes or No.
Press the ENTER button to save.
To return to a previous menu, press the MENU
button.
Notice an alternative shortcut for this
function: press the UP & DOWN
buttons together.
Backlight Auto Off
No: display is always lit.
Yes: display turns dark when not used for
some time.
Select “Backlight Auto Off” and press ENTER.
Use DOWN / UP buttons to select Yes or No.
Press the ENTER button to save.
To return to a previous menu, press the MENU
button.
Backlight Intensity
Used to set the intensity of the display
backlight.
Select Backlight Intensity and press ENTER.
Use DOWN / UP buttons to change the intensity
between 1 and 10.
Press the ENTER button to save.
To return to a previous menu, press the MENU button.
ENGLISH OPERATION MANUAL
BRITEQ
®
8/79 BTX-FALCON
Temperature Unit
The display can show temperature either in °C (Celsius) or °F (Fahrenheit)
°C: Temperature is shown in Celsius.
°F: Temperature is shown in Fahrenheit.
Select “Temperature Unit” and press ENTER.
Use DOWN / UP buttons to select °C or °F.
Press the ENTER button to save.
To return to a previous menu, press the MENU button.
Display Warning
You can choose if the projector warns you that an error occurred.
No: display only shows the error discretely
Yes: the display starts blinking while the error is shown on the display.
Select “Display Warning” and press ENTER.
Use DOWN / UP buttons to select Yes or No.
Press the ENTER button to save.
To return to a previous menu, press the MENU button.
Fixture Test
This submenu contains some features to quickly test the unit without the need for a controller.
Press the MENU button and select the Fixture Test submenu.
Auto Test
The uit performs an automatic test where all features are shown.
Select Auto Test and press ENTER.
The projector starts the automatic test function and returns to normal operation after the test.
To return to a previous menu or stop the test, press the MENU button.
Manual Test
You can check all functions one by one without the need for a DMX-controller.
Select Manual Test and press ENTER.
The display shows a list with all functions that can be tested.
Use DOWN / UP buttons to browse the list and press ENTER to select a function.
Use DOWN / UP buttons to adapt the values: 000 to 255.
Press MENU to return to the list and choose another function to test.
To stop the test, press the MENU button until you’re in the main menu.
Fixture Information
This submenu contains some useful information for servicing.
Press the MENU button and select the Fixture Information” submenu.
The display shows the following information:
Fixture use Hour”: shows how many hours the fixture was in use. (reset not possible)
Light Use Hour”: shows how many hours the led engine was switched on (can be reset to zero)
Firmware Version: press MENU to show the software version for the different processors.
To return, press the MENU button until you’re in the main menu.
Reset Functions
This submenu is used to reset the unit or parts of the unit.
Press the MENU button and select the Reset Functions submenu.
The display shows a list with different functions that can be rest: Pan/tilt, Color, Gobo, …, All.
Use DOWN / UP buttons to browse the list and press ENTER to select a function.
Use DOWN / UP buttons to confirm your choice: Yes or No.
Press MENU to return to the list and choose another function.
To return, press the MENU button until you’re in the main menu.
Notice an alternative shortcut for a complete reset of the projector: press the MENU & ENTER
buttons together for 3seconds.
ENGLISH OPERATION MANUAL
BRITEQ
®
9/79 BTX-FALCON
Special Functions
This submenu contains some useful functions for servicing.
Press the MENU button and select the Special Functions submenu.
Factory Settings
This is your emergency exit if you really messed up the settings: just return to factory settings.
No: keep the current settings unchanged.
Yes: return to factory settings, personal settings are lost.
Select “Factory Settings” and press ENTER
Use DOWN / UP buttons to select Yes or No.
Press the ENTER button to save.
To return to a previous menu, press the MENU button.
OFFSET ADJUST:
Used to adjust the home position of pan / tilt and zoom so
all units are perfectly aligned:
If you’re not already in the setup menu, just press the
MENU button shortly to enter the setup menu
Now press the ENTER button for at least 5 seconds to go
into offset mode.
Use DOWN / UP buttons to select one of the available
options.
Press the ENTER button, the display shows the actual
offset value.
Use DOWN / UP buttons to adjust the offset values
Press the ENTER button to confirm your setting or press the
MENU button to leave without saving the value.
To return to normal working mode: press the MENU button.
OVERHEAD RIGGING
Important: The installation must be carried out by qualified service personal only. Improper
installation can result in serious injuries and/or damage to property. Overhead rigging requires
extensive experience! Working load limits should be respected, certified installation materials
should be used, the installed device should be inspected regularly for safety.
Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging
and servicing.
Locate the fixture in a well ventilated spot, far away from any flammable materials and/or liquids. The
fixture must be fixed at least 50cm from surrounding walls.
The device should be installed out of reach of people and outside areas where persons may walk by or be
seated.
Before rigging make sure that the installation area can hold a minimum point load of 10times the device’s
weight.
Always use a certified safety cable that can hold 12 times the weight of the device when installing the unit.
This secondary safety attachment should be installed in a way that no part of the installation can drop
more than 20cm if the main attachment fails.
The device should be well fixed; a free-swinging mounting is dangerous and may not be considered!
Don’t cover any ventilation openings as this may result in overheating.
The operator has to make sure that the safety-relating and machine-technical installations are approved by
an expert before using them for the first time. The installations should be inspected every year by a skilled
person to be sure that safety is still optimal.
ENGLISH OPERATION MANUAL
BRITEQ
®
10/79 BTX-FALCON
ELECTRICAL INSTALLATION + ADDRESSING
Important: The electrical installation should be carried out by qualified personal only,
according to the regulations for electrical and mechanical safety in your country.
Every time you turn the unit on, it will show a welcome message on the display and move all the motors to
their ‘home’ position and you may hear some noises for about 20 seconds. After that the unit will be ready to
receive DMX signal or run the built-in programs.
Electrical installation for two or more units in master/slave:
In this mode the units will show a synchronized show, working to the rhythm of the beat.
Connect 2 to maximum 16 units together using good quality balanced microphone cables. The first unit in
the chain will automatically act as the master, the other units will act automatically as slaves.
Make sure that all units are connected to the mains.
The FIRST projector in the line should be set as MASTER! (also refer to the chapter SETUP MENU -
Show settings Offline mode):
Press the MENU button and select the “Show Settings” submenu
Select the “Offline Mode” submenu and select “M/S” (“M/S” stands for “master/slave” mode)
Select the “Show Mode” submenu and choose one of the Shows.
Done!
Remark1: if there’s no output, please make sure to set the first unit in “M/S” mode.
Remark2: if the units don’t follow the beats of the music, check on the master if “Sound Trigger” is set to ON
and the “Sound Sensitivity” is set at the desired level. (see chapter “SETUP MENU)
Electrical installation for several units on a DMX line:
The DMX-protocol is a widely used high speed signal to control intelligent light equipment.
You need to “daisy chain” your DMX controller and all the connected light effects with a
good quality XLR M/F balanced cable. To prevent strange behavior of the light effects, due
to interferences, you must use a 90Ω to 120Ω terminator at the end of the chain. Never use
Y-cables to split the DMX-line, instead use a good quality DMX splitter!
Each unit in the chain must have its proper starting address so it knows which commands from the controller
it has to decode.
ENGLISH OPERATION MANUAL
BRITEQ
®
11/79 BTX-FALCON
HOW TO SET THE RIGHT STARTING ADDRESS:
Refer to the chapter “SETUP MENU” to learn how to set the starting address on this unit. The starting
address of each unit is very important. If you want to control all projectors independently, you should give
them all a different start address and the DMX-channels of the different projectors may not overlap.
Example:
Projector1: start address = 001 (end address 017)
Projector2: start address = 018 (end address 034)
Projector3: start address = 035 (end address 051)
Unfortunately it is impossible to tell you in this user manual which starting addresses you have to use exactly
because this completely depends on the controller and setup you will use… So please refer to the user
manual of your DMX-controller to find out which starting addresses you must set.
DMX-CONFIGURATION:
Currently the projector has 1 DMX-mode, with eventual future software updates this could change.
CHANNEL
VALUE
FUNCTION
1
000 - 255
Pan
2
000 - 255
Pan Fine (Least significant bit)
3
000 - 255
Tilt
4
000 - 255
Tilt Fine (Least significant bit)
5
000 - 255
Pan / Tilt Speed (000 = fast ~ 255 = slow)
6
000 - 255
Dimmer (0 to 100%)
7
Strobe / Shutter effect
000 - 007
Shutter closed (no output)
008 - 015
Shutter open
016 - 131
Strobe 1 (slow fast)
132 - 139
Shutter open
140 - 181
Strobe 2: slow open / instant close (slow → fast)
182 - 189
Shutter open
190 - 231
Strobe 3: instant open / slow close (slow → fast)
232 - 239
Shutter open
240 - 247
Strobe 4: random strobe
248 - 255
Shutter open
8
Color wheel 1
000 - 007
COLOR 1 - White (open)
008 - 015
COLOR 2 - Light Blue
016 - 023
COLOR 3 - Green
024 - 031
COLOR 4 - Orange
032 - 039
COLOR 5 - Yellow
040 - 047
COLOR 6 - Magenta
048 - 055
COLOR 7 - Blue
056 - 063
COLOR 8 - Red
064 - 127
Indexing (intermediate positions)
128 - 189
Color wheel turning clockwise (fast → slow)
190 - 193
Color wheel stops turning
194 - 255
Color wheel turning counter clockwise (slow fast)
9
Color wheel 2
000 - 007
COLOR 1 - White (open)
008 - 015
COLOR 2 - Pink
016 - 023
COLOR 3 - CTO 3200K (warm white filter)
ENGLISH OPERATION MANUAL
BRITEQ
®
12/79 BTX-FALCON
024 - 031
COLOR 4 - UV light
032 - 039
COLOR 5 - Yellow
040 - 047
COLOR 6 Grass Green
048 - 055
COLOR 7 CTO 5600K (cold white)
056 - 063
COLOR 8 Pale Blue
064 - 127
Indexing (intermediate positions)
128 - 189
Color wheel turning clockwise (fast → slow)
190 - 193
Color wheel stops turning
194 - 255
Color wheel turning counter clockwise (slow fast)
10
Gobo wheel 1 - select (rotating gobos)
000 - 007
OPEN (no gobo)
008 - 015
GOBO 1
016 - 023
GOBO 2
024 - 031
GOBO 3
032 - 039
GOBO 4
040 - 047
GOBO 5
048 - 055
GOBO 6
056 - 063
GOBO 7
064 - 073
GOBO 1 Shaking
074 - 082
GOBO 2 Shaking
083 - 091
GOBO 3 Shaking
092 - 100
GOBO 4 Shaking
101 - 109
GOBO 5 Shaking
110 - 118
GOBO 6 Shaking
119 - 127
GOBO 7 Shaking
128 - 189
Gobo wheel turning clockwise (fast → slow)
190 - 193
Gobo wheel stops turning
194 - 255
Gobo wheel turning counter clockwise (slow fast)
11
Gobo wheel 1 - rotation
000 - 127
indexed positioning: 0° - 360°
128 - 189
Gobo turning clockwise (fast → slow)
190 - 193
Gobo stops turning
194 - 255
Gobo turning counter clockwise (slow → fast)
12
Gobo wheel 2 - select (static gobos)
000 - 007
OPEN (no gobo)
008 - 014
GOBO 1
015 - 021
GOBO 2
022 - 028
GOBO 3
029 - 035
GOBO 4
036 - 042
GOBO 5
043 - 049
GOBO 6
050 - 056
GOBO 7
057 - 063
GOBO 8
064 - 071
GOBO 1 Shaking
072 - 079
GOBO 2 Shaking
080 - 087
GOBO 3 Shaking
088 - 095
GOBO 4 Shaking
096 - 103
GOBO 5 Shaking
104 - 111
GOBO 6 Shaking
112 - 119
GOBO 7 Shaking
120 - 127
GOBO 8 Shaking
128 - 189
Gobo wheel turning clockwise (fast → slow)
190 - 193
Gobo wheel stops turning
ENGLISH OPERATION MANUAL
BRITEQ
®
13/79 BTX-FALCON
194 - 255
Gobo wheel turning counter clockwise (slow fast)
13
Prism on/off
000 - 127
Prism effect OFF
128 - 255
Prism effect ON
14
Prism - rotation
000 - 127
indexed positioning: 0° - 360°
128 - 189
Prism turning clockwise (fast → slow)
190 - 193
Prism stops turning
194 - 255
Prism turning counter clockwise (slow → fast)
15
000 - 255
Iris (maximum to minimum)
16
000 - 255
Focus (close to distant)
17
Special functions
000 - 069
No function
070 - 079
Activate blackout during pan/tilt (*)
080 - 089
Disable blackout during pan/tilt (*)
090 - 099
Activate blackout during color change (*)
100 - 109
Disable blackout during color change (*)
110 - 119
Activate blackout during gobo change (*)
120 - 129
Disable blackout during gobo change (*)
130 - 139
No function
140 - 149
Pan/tilt reset (*)
150 - 159
Color reset (*)
160 - 169
Gobo reset (*)
170 - 179
No function
180 - 189
Focus reset (*)
190 - 199
No function
200 - 209
Reset all (*)
210 - 219
Activate blackout during gobo/color or pan/tilt change (*)
220 - 229
Disable blackout during gobo/color or pan/tilt change (*)
230 - 255
No function
Note (*): function delay is set to 3seconds, the selected function will only be active while the corresponding
DMX-value is received during at least 3seconds.
ROTATING GOBOS (GOBO WHEEL1 CHANNEL 10
Gobo wheel 1 contains 7 standard rotating gobos (gobo size: 26,8mm image size: 22,0mm)
These gobos can be replace by your own custom gobos, both metal and glass gobos can be used.
Replacing the gobos:
Switch the projector off, unplug the power cable and wait until the unit is cool.
Remove the plastic cover of the head using a Phillips screwdriver (PH2)
Locate the gobo wheel with rotating gobos.
Each of the rotating gobos is mounted in a separate holder that can be easily removed from the wheel
just by lifting it up a little and tear it out.
The gobo is fixed in the holder using a wire clip: remove the wire clip gently.
Remove the gobo and replace it by a new one
Put the wire clip back in place and click the holder back in the gobo wheel.
Put the plastic cover of the head back in place using a Phillips screwdriver (PH2)
Done.
ENGLISH OPERATION MANUAL
BRITEQ
®
14/79 BTX-FALCON
FIXED GOBOS (GOBO WHEEL2 CHANNEL 12
Gobo wheel 2 contains 8 standard fixed gobos (gobo size: 31,4mm image size: 22,0mm)
These gobos can be replace by your own custom gobos, only metal gobos can be used.
Replacing the gobos:
Switch the projector off, unplug the power cable and wait until the unit is cool.
Remove the plastic cover of the head using a Phillips screwdriver (PH2)
Locate the gobo wheel with fixed gobos.
The gobos are fixed directly in the gobo wheel.
Remove the gobo gently and replace it by a new one.
Put the plastic cover of the head back in place using a Phillips screwdriver (PH2)
Done.
MAINTENANCE
Make sure the area below the installation place is free from unwanted persons during servicing.
Switch off the unit, unplug the mains cable and wait until the unit has been cooled down.
During inspection the following points should be checked:
All screws used for installing the device and any of its parts should be tightly fastened and may not be
corroded.
Housings, fixations and installations spots (ceiling, truss, suspensions) should be totally free from any
deformation.
When an optical lens is visibly damaged due to cracks or deep scratches, it must be replaced.
The mains cables must be in impeccable condition and should be replaced immediately when even a
small problem is detected.
In order to protect the device from overheat the cooling fans and ventilation openings should be cleaned
monthly.
The interior of the device should be cleaned annually using a vacuum cleaner or air-jet.
The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp,
smoky or particularly dirty surroundings can cause greater accumulation of dirt on the unit’s optics.
Clean with a soft cloth using normal glass cleaning products.
Always dry the parts carefully.
Attention: We strongly recommend internal cleaning to be carried out by qualified personnel!
ENGLISH OPERATION MANUAL
BRITEQ
®
15/79 BTX-FALCON
SPECIFICATIONS
Mains Input: AC 100 - 240V, 50/60Hz
Power consumption: 330 Watt
Fuse: 250V 6,3A slow blow (20mm glass)
Power connections: Neutrik® PowerCON® - 16A Power linking capacity.
DMX connections: 3pin-XLR & 5pin-XLR male / female
DMX channels used: 17ch
Lamp: 180W LED Engine
Beam Angle: 16°
Color wheel 1: 7 colors + open
Color wheel 2: 8 colors, including CTO 3200K, CTO 5600K and UV
GOBO wheel 1: 7 rotating gobos, replaceable by metal and glass gobos
Outer diameter: 26,8mm Image diameter: 22,0mm
GOBO wheel 2: 8 fixed gobos, replaceable only by metal gobos
Outer diameter: 31,4mm Image diameter: 22,0mm
IP-Rating: IP20
Operating temperature (T
a
): 0°C to 40°C
Installation: 2 quarter turn quick clamps
Size: see drawing below
Weight: 17,5 kg
The information might be modified without prior notice
You can download the latest version of this user manual on our website: www.briteq-lighting.com
FRANÇAIS GUIDE D'UTILISATION
BRITEQ
®
16/79 BTX-FALCON
GUIDE D'UTILISATION
Nous vous remercions d'avoir acheté ce produit BRITEQ. Pour tirer pleinement profit de toutes les
possibilités et pour votre propre sécurité, lisez ces instructions très attentivement avant d'utiliser cet appareil.
CARACTÉRISTIQUES
Cet appareil ne produit pas d'interférences radio. Ce produit répond aux exigences des directives européennes
et nationales actuelles. La conformité a été établie et les clarations et documents correspondants ont été
déposés par le fabricant.
Une lyre très lumineuse contrôlée par un module à LED tout neuf et puissant de 180W !
100% compatible avec notre fameuse BTX-180LS mais avec 40% plus de puissance lumineuse!
L'utilisation d'optique de pointe 16° permet de produire une lumière incroyablement forte : 221’700 lux @ 1m
Idéal pour les entreprises de location, scènes, discothèques, etc.
Les mouvements pan/tilt (540°/270°) très rapides assurent une programmation de spectacle très dynamique.
Résolution pan/tilt 8 ou 16 bits avec correction de position X/Y et canal de vitesse.
Les 17 canaux DMX offrent un grand nombre de possibilis et caractéristiques :
Netteté contrôlée électroniquement par DMX
Diaphragme contrôlé par DMX
2 roues de gobos pour des beaux effets de gobos superposés :
7 gobos rotatifs rapides + ouvert
8 gobos fixes + ouvert
2 roues de couleur, chacune avec 7 couleurs dichroïques soigneusement sélectionnées + ouvert
Gradateur/obturateur électronique extrêmement rapide
Prisme à 3 facettes à rotation rapide pour les effets spéciaux
Différents effets stroboscopiques
Canal d'effets : Allumage/Extinction de lampe à distance, différentes fonctions d'obscurcissement, etc.
Fonctionne également en mode autonome et mtre/esclave : les shows préprogrammés sont déclenchés
par le micro interne.
Entrées/sorties Neutrik PowerCon
®
: chaînage facile de plusieurs unités jusqu'à 16A.
Entrées/sorties Neutrik 3 et 5 broches pour un maximum de flexibilité dans un environnement professionnel
Les mises à jour faciles du micrologiciel permettent de maintenir votre appareil à jour en permanence (un
module de mise à jour optionnel est nécessaire)
L'écran LCD à matrice assure une navigation facile à travers les différents menus de configuration
Haut rendement et faible consommation d'énergie, uniquement 245 Watts
Equipé de supports Omega pour une installation rapide
AVANT UTILISATION
Avant d'utiliser cet appareil, vérifiez s'il n'a pas été endommagé durant le transport. En cas de dommages,
n'utilisez pas l'appareil et consultez immédiatement votre revendeur.
Important : Cet appareil est expédié de notre usine en parfait état et bien emballé. Il est absolument
nécessaire que l'utilisateur suive strictement les instructions et les avertissements de sécurité se trouvant
dans ce manuel. Tout dommage à une mauvaise manipulation n'est pas garanti. Le revendeur
n'accepte aucune responsabilité pour tous les défauts et problèmes dus au non-respect de ce manuel.
Conservez ce manuel dans un endroit sûr pour toute consultation future. Si vous vendez l'appareil, veillez
à joindre ce manuel.
Vérifiez le contenu :
Vérifiez que le carton contient les éléments suivants :
Instructions d'utilisation
Lyre BTX-FALCON
2 attaches rapides « Omega »
Câble PowerCon
®
FRANÇAIS GUIDE D'UTILISATION
BRITEQ
®
17/79 BTX-FALCON
INSTRUCTIONS DE SÉCURITÉ :
Pour protéger l'environnement, essayer de recycler autant que possible les matériaux d'emballage.
Pour éviter tout incendie ou électrocution, n'exposez pas cet appareil à la pluie ou l'humidité.
Pour éviter une formation de condensation interne, laissez l'appareil s'adapter à la température ambiante
quand vous le mettez dans une pièce chaude après le transport. La condensation empêche parfois
l'appareil de fonctionner à plein rendement ou peut même causer des dommages.
Cet appareil est destiné à un usage intérieur seulement.
Ne placez pas d'objets métalliques et ne renversez pas de liquides à l'intérieur de l'appareil. Un choc
électrique ou un dysfonctionnement peut en résulter. Si un corps étranger pénètre dans l'appareil,
débranchez immédiatement le cordon d'alimentation de la prise secteur.
Placez l'appareil dans un endroit bien aéré, loin de tout matériau et/ou liquide inflammable. L'appareil doit
être fixé à au moins 50cm des murs environnants.
Ne couvrez pas les ouvertures de ventilation, cela pourrait entraîner une surchauffe.
Évitez une utilisation dans des environnements poussiéreux et nettoyez l'appareil régulièrement.
Gardez l'appareil loin de la portée des enfants.
Les personnes inexpérimentées ne doivent pas utiliser cet appareil.
La température ambiante de fonctionnement maximale est de 40°C. N'utilisez pas cet appareil à des
températures ambiantes plus élevées.
Assurez-vous qu'aucune personne étrangère ne se trouve dans la zone en dessous de l'emplacement
d'installation durant le montage, le démontage et l'entretien.
Laissez environ 10 minutes à l'appareil pour refroidir avant de commencer l'entretien.
Débranchez toujours l'appareil lorsqu'il ne va pas être utilisé pendant une longue période ou avant de
commencer l'entretien.
L'installation électrique doit être effectuée par du personnel qualifié, conformément à la réglementation en
matière de sécurité électrique et mécanique dans votre pays.
Vérifiez que la tension secteur n'est pas supérieure à celle indiquée sur l'appareil.
Le cordon d'alimentation doit toujours être en parfait état. Éteignez immédiatement l'appareil dès que le
cordon d'alimentation est écrasé ou endommagé. Il doit être remplacé par le fabricant, son agent de
service ou une personne de même qualification afin d'éviter tout danger.
Ne laissez jamais le cordon d'alimentation ENTRER en contact avec d'autres câbles !
Ce luminaire doit être mis à la terre pour être conforme réglementation en matière de sécurité.
Ne connectez pas l'appareil à un variateur de lumière.
Utilisez toujours un câble de sécurité approprié et certifié lors de l'installation de l'appareil.
Afin d'éviter un choc électrique, n'ouvrez aucun panneau. L'appareil ne contient aucun composant
réparable par l'utilisateur.
ATTENTION : Pour réduire le risque de choc électrique, ne
retirez pas le panneau supérieur. L'appareil ne contient aucun
composant réparable par l'utilisateur. Confiez toute réparation à
un personnel qualifié uniquement.
Le symbole de l'éclair à l'intérieur d'un triangle équilatéral, est destià alerter l'utilisateur de la
présence de « tensions dangereuses » non isolées à l'intérieur de l'appareil, d'une magnitude
pouvant constituer un risque d'électrocution.
Le symbole du point d'exclamation dans un triangle équilatéral sert à avertir l'utilisateur que
d'importants conseils d'utilisation et de maintenance sont fournis dans la documentation
accompagnant l'appareil.
Ce symbole signifie : pour usage intérieur uniquement.
Ce symbole signifie : Lisez les instructions.
Ce symbole détermine : la distance minimale requises avec les objets éclairés. La distance
minimale entre la sortie de lumière et la surface éclairée doit être supérieure à 2 mètres.
Cet appareil n'est pas adapté pour un montage direct sur des surfaces normalement
inflammables. (ne convient que pour le montage sur surfaces non combustibles)
ATTENTION : Ne fixez pas votre regard sur une lampe allumée.
Peut être nocif pour les yeux.
FRANÇAIS GUIDE D'UTILISATION
BRITEQ
®
18/79 BTX-FALCON
Ne réparez jamais un fusible et ne court-circuitez jamais le porte-fusible. Remplacez toujours un fusible
endommagé par un fusible du même type ayant les mêmes spécifications électriques !
En cas de sérieux problèmes de fonctionnement, cessez d'utiliser l'appareil et contactez immédiatement
votre revendeur.
Le boîtier et l'objectif doivent être remplacés s'ils sont visiblement endommagés.
Utilisez l'emballage d'origine pour transporter l'appareil.
Pour des raisons de sécurité, il est interdit d'apporter des modifications non autorisées à l'appareil.
Important : Ne regardez jamais directement la source de lumière ! N'utilisez pas le jeu de lumière en
présence de personnes souffrant d'épilepsie.
DESCRIPTION :
PANNEAU DE COMMANDE :
1. Témoins d'état : témoins utilisés pour indiquer l'état du projecteur.
DMX
présence d'entrée DMX, clignote pendant la mise à jour du
logiciel
MASTER
le projecteur fonctionne en mode maître
SLAVE
le projecteur fonctionne en mode esclave
SOUND
Indique une activité audio
2. L'écran : affiche les différents menus et les fonctions sélectionnées.
3. TOUCHES DE NAVIGATION :
MENU
Permet d'accéder au menu configuration ou de retourner à une fonction
précédente
BAS
Permet de descendre dans l'arborescence des menus
HAUT
Permet de remonter dans l'arborescence des menus
ENTER
Pour confirmer les fonctions sélectionnées
Deux touches raccourcis facilitent le travail de l'installateur :
Appuyez sur Haut et Bas en même temps : Permet de faire pivoter l'affichage de 180°.
Maintenez appuyées MENU + ENTER pendant 3 secondes : le projecteur retrouve sa position
initiale.
4. Attache Omega : vous pouvez utiliser l'attache rapide « oméga » incluse en dessous de l’appareil. Il
suffit de faire pivoter le système de verrouillage sur 90° pour fixer l'attache. Utilisez toujours un câble de
sécurité pour plus de sécurité !
5. ENTREES/SORTIES DMX : utilisé pour des configurations en DMX512, vous pouvez utiliser des câbles
de signaux symétriques de bonne qualité avec connecteurs XLR 3 ou 5 broches.
6. FUSIBLE SECTEUR : ce fusible ne protège que la partie électronique du projecteur, l'entrée/sortie (7)
secteur n'est pas protégée par fusible.
7. ENTRÉE ET SORTIE SECTEUR : Utilisez les prises POWERCON
®
pour brancher le câble
d'alimentation fourni ici ; vous pouvez connecter en rie plusieurs unités, jusqu'à 16A maximum. Aucun
fusible n'est utilisé au niveau des entrées et sorties raccordées.
Astuce : Veuillez consulter notre site Web pour les assemblages de câbles spéciaux qui offrent une
puissance (3x1,5mm² avec Neutrik PowerCon
®
) et un signal symétrique (XLR 3 broches) dans un seul câble.
Différentes longueurs sont disponibles : 1,3m, 3m, 5m et 10m, très pratiques !
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84

Briteq BTX-FALCON Le manuel du propriétaire

Catégorie
Projecteurs
Taper
Le manuel du propriétaire