Briteq BTX-FALCON Le manuel du propriétaire

ENGLISH OPERATION MANUAL

BRITEQ

®

1/79 BTX-FALCON

OPERATION MANUAL

Thank you for buying this BRITEQ product. To take full advantage of all possibilities and for your own safety,

please read these operating instructions very carefully before you start using this unit.

FEATURES

This unit is radio-interference suppressed. This product meets the requirements of the current European and

national guidelines. Conformity has been established and the relevant statements and documents have been

deposited by the manufacturer.

 A very bright moving head projector based on a brand-new powerful 180W LED engine!

 100% backward compatible with our famous BTX-180LS but with over 40% more lumen output !

 The use of advanced 16° optics guarantees an incredibly bright output: 221’700 lux @ 1m

 Perfect for rental companies, stage, discotheques, …

 The very fast pan/tilt movements (540°/270°) assure very dynamic show programming.

 8 or 16bit resolution pan/tilt resolution with X/Y position correction and pan/tilt speed channel.

 Uses 17 DMX channels for an excellent range of possibilities and specs:

 DMX-controlled electronic focus

 DMX-controlled iris

 2 gobo wheels for nice gobo overlay effects:

 7 fast rotating gobos + open

 8 fixed gobos + open

 2 color wheels, each with 7 carefully selected dichroic colors + open

 Extremely fast electronic dimmer/shutter

 Fast rotating 3facet prism for special effects

 Different strobe effects

 Effect channel: remote lamp on/off control, different blackout functions, etc.

 Works also in standalone & master/slave mode: the internal mic triggers the preprogrammed shows.

 Neutrik PowerCON

®

in/outputs: easy daisy chaining of several units up to 16A.

 Neutrik 3pin & 5pin in/outputs for maximum flexibility in a professional environment

 Easy firmware updates keep your machine up-to-date at all times (optional firmware updater needed)

 The matrix LCD-display assures easy navigation in the different setup menus

 High efficiency and low power consumption, only 245W

 Equipped with omega brackets for fast installation

BEFORE USE

 Before you start using this unit, please check if there’s no transportation damage. Should there be any, do

not use the device and consult your dealer first.

 Important: This device left our factory in perfect condition and well packaged. It is absolutely necessary

for the user to strictly follow the safety instructions and warnings in this user manual. Any damage caused

by mishandling is not subject to warranty. The dealer will not accept responsibility for any resulting defects

or problems caused by disregarding this user manual.

 Keep this booklet in a safe place for future consultation. If you sell the fixture, be sure to add this user

manual.

Check the contents:

Check that the carton contains the following items:

 Operating instructions

 BTX-FALCON projector

 2pcs Quick lock “Omega bracket”

 PowerCON

®

cable

ENGLISH OPERATION MANUAL

BRITEQ

®

2/79 BTX-FALCON

SAFETY INSTRUCTIONS:

 To protect the environment, please try to recycle the packing material as much as possible.

 To prevent fire or shock hazard, do not expose this appliance to rain or moisture.

 To avoid condensation to be formed inside, allow the unit to adapt to the surrounding temperatures when

bringing it into a warm room after transport. Condense sometimes prevents the unit from working at full

performance or may even cause damages.

 This unit is for indoor use only.

 Don’t place metal objects or spill liquid inside the unit. Electric shock or malfunction may result. If a foreign

object enters the unit, immediately disconnect the mains power.

 Locate the fixture in a well ventilated spot, away from any flammable materials and/or liquids. The fixture

must be fixed at least 50cm from surrounding walls.

 Don’t cover any ventilation openings as this may result in overheating.

 Prevent use in dusty environments and clean the unit regularly.

 Keep the unit away from children.

 Inexperienced persons should not operate this device.

 Maximum safe ambient temperature is 40°C. Don’t use this unit at higher ambient temperatures.

 Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging

and servicing.

 Allow the device about 10 minutes to cool down before to start servicing.

 Always unplug the unit when it is not used for a longer time or before to start servicing.

 The electrical installation should be carried out by qualified personal only, according to the regulations for

electrical and mechanical safety in your country.

 Check that the available voltage is not higher than the one stated on the unit.

 The power cord should always be in perfect condition. Switch the unit immediately off when the power cord

is squashed or damaged. It must be replaced by the manufacturer, its service agent or similarly qualified

persons in order to avoid a hazard.

 Never let the power-cord come into contact with other cables!

 This fixture must be earthed in order to comply with safety regulations.

 Don’t connect the unit to any dimmer pack.

 Always use an appropriate and certified safety cable when installing the unit.

 In order to prevent electric shock, do not open the cover. There are no user serviceable parts inside.

 Never repair a fuse or bypass the fuse holder. Always replace a damaged fuse with a fuse of the same

type and electrical specifications!

 In the event of serious operating problems, stop using the fixture and contact your dealer immediately.

 The housing and the lenses must be replaced if they are visibly damaged.

 Please use the original packing when the device is to be transported.

CAUTION: To reduce the risk of electric shock, do not remove

the top cover. No user-serviceable parts inside. Refer servicing

to qualified service personnel only.

The lightning flash with arrowhead symbol within the equilateral triangle is intended to alert the

use or the presence of un-insulated “dangerous voltage” within the product’s enclosure that may

be of sufficient magnitude to constitute a risk of electric shock.

The exclamation point within the equilateral triangle is intended to alert the user to the presence

of important operation and maintenance (servicing) instructions in the literature accompanying

this appliance.

This symbol means: indoor use only

This symbol means: Read instructions

This symbol determines: the minimum distance from lighted objects. The minimum distance

between light-output and the illuminated surface must be more than 2 meters

The device is not suitable for direct mounting on normally flammable surfaces. (suitable only for

mounting on non-combustible surfaces)

CAUTION: Do not stare at operating lamp.

May be harmful to the eyes.

ENGLISH OPERATION MANUAL

BRITEQ

®

3/79 BTX-FALCON

 Due to safety reasons it is prohibited to make unauthorized modifications to the unit.

Important: Never look directly into the light source! Don’t use the effect in the presence of persons suffering

from epilepsy.

DESCRIPTION:

CONTROL PANEL:

1. STATUS LEDS: leds used to indicate the status of the projector.

DMX

On

DMX input present, blinks during a software update

MASTER

On

Projector works in master mode

SLAVE

On

Projector works in slave mode

SOUND

Flashing

Shows audio activity

2. DISPLAY shows the various menus and the selected functions.

3. NAVIGATION BUTTONS:

MENU

To enter the setup menu or return to a previous function

DOWN

To go forward in the menu tree

UP

To go backward in the menu tree

ENTER

To confirm the selected function

Two button shortcuts make life easier for the installer:

 Press UP & DOWN buttons together: Display turns over 180°

 Press MENU + ENTER buttons for 3sec: the projector resets.

4. OMEGA CLAMP: on the bottom you can insert the included “omega” quick clamp. Just turn the locking

system over 90° to secure the clamp. Always use a safety cable for extra security!

5. DMX IN/OUTPUTS: used for DMX512 linking, you can use good quality balanced signal cables with 3pin

or 5pin XLR-connectors.

6. MAINS FUSE: this fuse only protects the electronics of the projector, mains input/output (7) is not fused.

7. MAINS INPUT / OUTPUT: with PowerCON

®

sockets, connect the supplied mains cable here, you can

daisy chain several units, up to max 16A. Input and output are connected to each other without any fuse.

Hint: Please check our website for special cable assemblies that contain both power (3x1.5mm² with Neutrik

PowerCON

®

) and balanced signal (XLR 3pin) in one cable. Different lengths are available: 1.3m, 3m, 5m and

10m, very convenient!

ENGLISH OPERATION MANUAL

BRITEQ

®

4/79 BTX-FALCON

SETUP MENU:

 Press the MENU button to enter the setup menu.

 Use UP / DOWN buttons to browse the submenu(s) and/or select functions, change the value(s).

 Always press the ENTER button to confirm.

 To return to a previous menu, always use the MENU button.

Note 1: After 60 seconds the display will automatically return to normal mode without any change.

Note 2: The grey colored options in the setup menu are the default settings.

DMX Functions

This submenu contains all DMX-related settings.

 Press the MENU button and select the “DMX Functions” submenu.

DMX Address

Used to set the starting address in a DMX

setup.

 Select “DMX address” and press ENTER.

 Use DOWN / UP buttons to change the

DMX512 address.

 Press the ENTER button to save.

To return to a previous menu, press the MENU

button.

DMX Channel Mode

Used to select the desired channel mode.

 Select “DMX Channel Mode” and press

ENTER

 Use DOWN / UP buttons to select the desired

DMX channel mode.

 Press the ENTER button to save.

To return to a previous menu, press the MENU

button.

View DMX Value

 Select “View DMX Value” and press ENTER.

 The display now shows the DMX-values for the

different channels.

To return to a previous menu, press the MENU

button or after 60 seconds the display will

automatically return to normal mode.

Show Settings

This submenu contains specific settings for

when the projector is used in standalone or

master/slave mode (without DMX controller).

 Press the MENU button and select the “Show

Settings” submenu.

Offline Mode

Determines how the projector should behave

when the DMX-signal is lost or not connected

(so it is “offline”).

 M/S mode (master/slave mode): when no

DMX-signal is detected, the projector starts

working in standalone mode. The internal

programs will be triggered to the rhythm of the

music by the built-in microphone.

 Hold mode: when no DMX-signal is detected,

the unit freezes with the latest dmx values

received and waits for the DMX-signal.

ENGLISH OPERATION MANUAL

BRITEQ

®

5/79 BTX-FALCON

 Blackout mode: when no DMX-signal is detected, the unit goes in blackout and waits for the DMX-signal.

 Select “Offline Mode” and press ENTER

 Use DOWN / UP buttons to select one of the available options.

 Press the ENTER button to save.

To return to a previous menu, press the MENU button.

Show Mode

Used to choose the Show mode when used in standalone or master/slave mode.

 Select “Show Mode” and press ENTER

 Use DOWN / UP buttons to select one of the available Shows.

 Press the ENTER button to save.

To return to a previous menu, press the MENU button.

Slave Mode

Used to make the slave unit work in opposite to the master or to work in complete sync.

 Select “Slave Mode” and press ENTER

 Use DOWN / UP buttons to select one of the available options:

 Slave1: the slave follows the master in complete sync

 Slave2: the slave follows the master in opposite sync

 Press the ENTER button to save.

To return to a previous menu, press the MENU button.

Focus 1

Used to help you adjusting the focus of the rotating gobos (gobo wheel 1) while used in standalone

mode.

 Select “Focus 1” and press ENTER: the projector shows one of the rotating gobos so you can easily

adjust the focus.

 Use DOWN / UP buttons until the gobo is sharp (value range: 0-255)

 Press the ENTER button to save.

To return to a previous menu, press the MENU button.

Remark: please note that you can only set an “average focus” , while in standalone mode it is not possible to

set the focus perfectly sharp for all directions.

Focus 2

Used to help you adjusting the focus of the fixed gobos (gobo wheel 2) while used in standalone

mode.

 Select “Focus 2” and press ENTER: the projector shows one of the fixed gobos so you can easily adjust

the focus.

 Use DOWN / UP buttons until the gobo is sharp (value range: 0-255)

 Press the ENTER button to save.

To return to a previous menu, press the MENU button.

Remark: please note that you can only set an “average focus” , while in standalone mode it is not possible to

set the focus perfectly sharp for all directions.

Sound Trigger

If switch on, the unit works to rhythm of the beat while used in standalone or master/slave mode

 Select “Sound Trigger” and press ENTER

 Use DOWN / UP buttons to select:

 On: internal shows triggered by the internal microphone

 Off: internal shows triggered at a preset slow speed.

 Press the ENTER button to save.

To return to a previous menu, press the MENU button.

Sound Sensitivity

Used to set the sensitivity of the internal microphone while used in standalone or master/slave mode

 Select “Sound Sensitivity” and press ENTER

 Use DOWN / UP buttons to change the sensitivity from 0 (very low sensitivity) to 100 (high sensitivity).

 Press the ENTER button to save.

To return to a previous menu, press the MENU button.

ENGLISH OPERATION MANUAL

BRITEQ

®

6/79 BTX-FALCON

Fixture Settings

This submenu contains specific fixture settings.

 Press the MENU button and select the “Fixture Settings” submenu.

Pan Inverse

No: Panning movement is not inverted.

Yes: Panning movement is inverted.

 Select “Pan Inverse” and press ENTER

 Use DOWN / UP buttons to select Yes or No.

 Press the ENTER button to save.

To return to a previous menu, press the MENU button.

Tilt Inverse

No: Tilt movement is not inverted.

Yes: Tilt movement is inverted.

 Select “Tilt Inverse” and press ENTER

 Use DOWN / UP buttons to select Yes or No.

 Press the ENTER button to save.

To return to a previous menu, press the MENU button.

P/T Feedback

While touching the head of the projector, the pan/tilt positioning can be disturbed and not in sync with the

other machines. P/T Feedback can automatically correct such issues.

 Select “P/T Feedback” and press ENTER

 Use DOWN / UP buttons to select:

 No: Pan/Tilt are not automatically corrected.

 Yes: Pan/Tilt are automatically corrected.

 Press the ENTER button to save.

To return to a previous menu, press the MENU button.

Iris Inverse

Used to determine the iris behavior.

 Select “Iris Inverse” and press ENTER

 Use DOWN / UP buttons to select:

 No: Iris is open while DMX-value is 000.

 Yes: Iris is open while DMX-value is 255.

 Press the ENTER button to save.

To return to a previous menu, press the MENU button.

Bl.O. P/T Moving

“Blackout while Pan/tilt are moving”: while pan/tilt positions are changing the projector can cut off the

output to obtain a special effect.

 Select “Bl.O. P/T Moving” and press ENTER

 Use DOWN / UP buttons to select:

 No: output stays on during pan/tilt movements.

 Yes: output shuts off during pan/tilt movements.

 Press the ENTER button to save.

To return to a previous menu, press the MENU button.

Bl.O. Color Change

“Blackout while changing the colors”: while colors are changing the projector can cut off the output to

obtain a special effect.

 Select “Bl.O. Color Change” and press ENTER

 Use DOWN / UP buttons to select:

 No: output stays on during color changes.

 Yes: output shuts off during color changes.

 Press the ENTER button to save.

To return to a previous menu, press the MENU button.

ENGLISH OPERATION MANUAL

BRITEQ

®

7/79 BTX-FALCON

Bl.O. Gobo Change

“Blackout while changing the gobos”: while gobos are changing the projector can cut off the output to

obtain a special effect.

 Select “Bl.O. Gobo Change” and press ENTER

 Use DOWN / UP buttons to select:

 No: output stays on during gobo changes.

 Yes: output shuts off during gobo changes.

 Press the ENTER button to save.

To return to a previous menu, press the MENU button.

Brightness Cali

Although the BTX-FALCON is 100% backward compatible with the previous BTX-180LS, the new

LED-engine in the BTX-FALCON has about 40% more output. With this function you can match

(reduce) the light output with that of the BTX-180LS.

 Select “Brightness Cali” and press ENTER

 Use DOWN / UP buttons to change the light output from 50% to 100%.

(a value of about 60% will match with the BTX-180LS)

 Press the ENTER button to save.

To return to a previous menu, press the MENU button.

Display Settings

This submenu contains display related settings

 Press the MENU button and select the “Display Settings” submenu.

Display Inverse

The projector can be fixed/used in upward position

or hung in upside-down position. To make reading

of the display easier, you can turn it over 180°.

No: Display readable while the projector is in

upward position.

Yes: Display readable while the projector is in

upside-down position.

 Select “Display Inverse” and press ENTER

 Use DOWN / UP buttons to select Yes or No.

 Press the ENTER button to save.

To return to a previous menu, press the MENU

button.

 Notice an alternative shortcut for this

function: press the UP & DOWN

buttons together.

Backlight Auto Off

No: display is always lit.

Yes: display turns dark when not used for

some time.

 Select “Backlight Auto Off” and press ENTER.

 Use DOWN / UP buttons to select Yes or No.

 Press the ENTER button to save.

To return to a previous menu, press the MENU

button.

Backlight Intensity

Used to set the intensity of the display

backlight.

 Select “Backlight Intensity” and press ENTER.

 Use DOWN / UP buttons to change the intensity

between 1 and 10.

 Press the ENTER button to save.

To return to a previous menu, press the MENU button.

ENGLISH OPERATION MANUAL

BRITEQ

®

8/79 BTX-FALCON

Temperature Unit

The display can show temperature either in °C (Celsius) or °F (Fahrenheit)

°C: Temperature is shown in Celsius.

°F: Temperature is shown in Fahrenheit.

 Select “Temperature Unit” and press ENTER.

 Use DOWN / UP buttons to select °C or °F.

 Press the ENTER button to save.

To return to a previous menu, press the MENU button.

Display Warning

You can choose if the projector warns you that an error occurred.

No: display only shows the error discretely

Yes: the display starts blinking while the error is shown on the display.

 Select “Display Warning” and press ENTER.

 Use DOWN / UP buttons to select Yes or No.

 Press the ENTER button to save.

To return to a previous menu, press the MENU button.

Fixture Test

This submenu contains some features to quickly test the unit without the need for a controller.

 Press the MENU button and select the “Fixture Test” submenu.

Auto Test

The uit performs an automatic test where all features are shown.

 Select “Auto Test” and press ENTER.

 The projector starts the automatic test function and returns to normal operation after the test.

To return to a previous menu or stop the test, press the MENU button.

Manual Test

You can check all functions one by one without the need for a DMX-controller.

 Select “Manual Test” and press ENTER.

 The display shows a list with all functions that can be tested.

 Use DOWN / UP buttons to browse the list and press ENTER to select a function.

 Use DOWN / UP buttons to adapt the values: 000 to 255.

 Press MENU to return to the list and choose another function to test.

To stop the test, press the MENU button until you’re in the main menu.

Fixture Information

This submenu contains some useful information for servicing.

 Press the MENU button and select the “Fixture Information” submenu.

 The display shows the following information:

 “Fixture use Hour”: shows how many hours the fixture was in use. (reset not possible)

 “Light Use Hour”: shows how many hours the led engine was switched on (can be reset to zero)

 “Firmware Version”: press MENU to show the software version for the different processors.

To return, press the MENU button until you’re in the main menu.

Reset Functions

This submenu is used to reset the unit or parts of the unit.

 Press the MENU button and select the “Reset Functions” submenu.

 The display shows a list with different functions that can be rest: Pan/tilt, Color, Gobo, …, All.

 Use DOWN / UP buttons to browse the list and press ENTER to select a function.

 Use DOWN / UP buttons to confirm your choice: Yes or No.

 Press MENU to return to the list and choose another function.

To return, press the MENU button until you’re in the main menu.

 Notice an alternative shortcut for a complete reset of the projector: press the MENU & ENTER

buttons together for 3seconds.

ENGLISH OPERATION MANUAL

BRITEQ

®

9/79 BTX-FALCON

Special Functions

This submenu contains some useful functions for servicing.

 Press the MENU button and select the “Special Functions” submenu.

Factory Settings

This is your emergency exit if you really messed up the settings: just return to factory settings.

No: keep the current settings unchanged.

Yes: return to factory settings, personal settings are lost.

 Select “Factory Settings” and press ENTER

 Use DOWN / UP buttons to select Yes or No.

 Press the ENTER button to save.

To return to a previous menu, press the MENU button.

OFFSET ADJUST:

Used to adjust the home position of pan / tilt and zoom so

all units are perfectly aligned:

 If you’re not already in the setup menu, just press the

MENU button shortly to enter the setup menu

 Now press the ENTER button for at least 5 seconds to go

into offset mode.

 Use DOWN / UP buttons to select one of the available

options.

 Press the ENTER button, the display shows the actual

offset value.

 Use DOWN / UP buttons to adjust the offset values

 Press the ENTER button to confirm your setting or press the

MENU button to leave without saving the value.

To return to normal working mode: press the MENU button.

OVERHEAD RIGGING

 Important: The installation must be carried out by qualified service personal only. Improper

installation can result in serious injuries and/or damage to property. Overhead rigging requires

extensive experience! Working load limits should be respected, certified installation materials

should be used, the installed device should be inspected regularly for safety.

 Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging

and servicing.

 Locate the fixture in a well ventilated spot, far away from any flammable materials and/or liquids. The

fixture must be fixed at least 50cm from surrounding walls.

 The device should be installed out of reach of people and outside areas where persons may walk by or be

seated.

 Before rigging make sure that the installation area can hold a minimum point load of 10times the device’s

weight.

 Always use a certified safety cable that can hold 12 times the weight of the device when installing the unit.

This secondary safety attachment should be installed in a way that no part of the installation can drop

more than 20cm if the main attachment fails.

 The device should be well fixed; a free-swinging mounting is dangerous and may not be considered!

 Don’t cover any ventilation openings as this may result in overheating.

 The operator has to make sure that the safety-relating and machine-technical installations are approved by

an expert before using them for the first time. The installations should be inspected every year by a skilled

person to be sure that safety is still optimal.

ENGLISH OPERATION MANUAL

BRITEQ

®

10/79 BTX-FALCON

ELECTRICAL INSTALLATION + ADDRESSING

Important: The electrical installation should be carried out by qualified personal only,

according to the regulations for electrical and mechanical safety in your country.

Every time you turn the unit on, it will show a welcome message on the display and move all the motors to

their ‘home’ position and you may hear some noises for about 20 seconds. After that the unit will be ready to

receive DMX signal or run the built-in programs.

Electrical installation for two or more units in master/slave:

In this mode the units will show a synchronized show, working to the rhythm of the beat.

 Connect 2 to maximum 16 units together using good quality balanced microphone cables. The first unit in

the chain will automatically act as the master, the other units will act automatically as slaves.

 Make sure that all units are connected to the mains.

 The FIRST projector in the line should be set as MASTER! (also refer to the chapter “SETUP MENU -

Show settings – Offline mode”):

 Press the MENU button and select the “Show Settings” submenu

 Select the “Offline Mode” submenu and select “M/S” (“M/S” stands for “master/slave” mode)

 Select the “Show Mode” submenu and choose one of the Shows.

 Done!

Remark1: if there’s no output, please make sure to set the first unit in “M/S” mode.

Remark2: if the units don’t follow the beats of the music, check on the master if “Sound Trigger” is set to ON

and the “Sound Sensitivity” is set at the desired level. (see chapter “SETUP MENU”)

Electrical installation for several units on a DMX line:

The DMX-protocol is a widely used high speed signal to control intelligent light equipment.

You need to “daisy chain” your DMX controller and all the connected light effects with a

good quality XLR M/F balanced cable. To prevent strange behavior of the light effects, due

to interferences, you must use a 90Ω to 120Ω terminator at the end of the chain. Never use

Y-cables to split the DMX-line, instead use a good quality DMX splitter!

Each unit in the chain must have its proper starting address so it knows which commands from the controller

it has to decode.

ENGLISH OPERATION MANUAL

BRITEQ

®

11/79 BTX-FALCON

HOW TO SET THE RIGHT STARTING ADDRESS:

Refer to the chapter “SETUP MENU” to learn how to set the starting address on this unit. The starting

address of each unit is very important. If you want to control all projectors independently, you should give

them all a different start address and the DMX-channels of the different projectors may not overlap.

Example:

 Projector1: start address = 001 (end address 017)

 Projector2: start address = 018 (end address 034)

 Projector3: start address = 035 (end address 051)

 …

Unfortunately it is impossible to tell you in this user manual which starting addresses you have to use exactly

because this completely depends on the controller and setup you will use… So please refer to the user

manual of your DMX-controller to find out which starting addresses you must set.

DMX-CONFIGURATION:

Currently the projector has 1 DMX-mode, with eventual future software updates this could change.

CHANNEL

VALUE

FUNCTION

1

000 - 255

Pan

2

000 - 255

Pan Fine (Least significant bit)

3

000 - 255

Tilt

4

000 - 255

Tilt Fine (Least significant bit)

5

000 - 255

Pan / Tilt Speed (000 = fast ~ 255 = slow)

6

000 - 255

Dimmer (0 to 100%)

7

Strobe / Shutter effect

000 - 007

Shutter closed (no output)

008 - 015

Shutter open

016 - 131

Strobe 1 (slow → fast)

132 - 139

Shutter open

140 - 181

Strobe 2: slow open / instant close (slow → fast)

182 - 189

Shutter open

190 - 231

Strobe 3: instant open / slow close (slow → fast)

232 - 239

Shutter open

240 - 247

Strobe 4: random strobe

248 - 255

Shutter open

8

Color wheel 1

000 - 007

COLOR 1 - White (open)

008 - 015

COLOR 2 - Light Blue

016 - 023

COLOR 3 - Green

024 - 031

COLOR 4 - Orange

032 - 039

COLOR 5 - Yellow

040 - 047

COLOR 6 - Magenta

048 - 055

COLOR 7 - Blue

056 - 063

COLOR 8 - Red

064 - 127

Indexing (intermediate positions)

128 - 189

Color wheel turning clockwise (fast → slow)

190 - 193

Color wheel stops turning

194 - 255

Color wheel turning counter clockwise (slow → fast)

9

Color wheel 2

000 - 007

COLOR 1 - White (open)

008 - 015

COLOR 2 - Pink

016 - 023

COLOR 3 - CTO 3200K (warm white filter)

ENGLISH OPERATION MANUAL

BRITEQ

®

12/79 BTX-FALCON

024 - 031

COLOR 4 - UV light

032 - 039

COLOR 5 - Yellow

040 - 047

COLOR 6 – Grass Green

048 - 055

COLOR 7 – CTO 5600K (cold white)

056 - 063

COLOR 8 – Pale Blue

064 - 127

Indexing (intermediate positions)

128 - 189

Color wheel turning clockwise (fast → slow)

190 - 193

Color wheel stops turning

194 - 255

Color wheel turning counter clockwise (slow → fast)

10

Gobo wheel 1 - select (rotating gobos)

000 - 007

OPEN (no gobo)

008 - 015

GOBO 1

016 - 023

GOBO 2

024 - 031

GOBO 3

032 - 039

GOBO 4

040 - 047

GOBO 5

048 - 055

GOBO 6

056 - 063

GOBO 7

064 - 073

GOBO 1 – Shaking

074 - 082

GOBO 2 – Shaking

083 - 091

GOBO 3 – Shaking

092 - 100

GOBO 4 – Shaking

101 - 109

GOBO 5 – Shaking

110 - 118

GOBO 6 – Shaking

119 - 127

GOBO 7 – Shaking

128 - 189

Gobo wheel turning clockwise (fast → slow)

190 - 193

Gobo wheel stops turning

194 - 255

Gobo wheel turning counter clockwise (slow → fast)

11

Gobo wheel 1 - rotation

000 - 127

indexed positioning: 0° - 360°

128 - 189

Gobo turning clockwise (fast → slow)

190 - 193

Gobo stops turning

194 - 255

Gobo turning counter clockwise (slow → fast)

12

Gobo wheel 2 - select (static gobos)

000 - 007

OPEN (no gobo)

008 - 014

GOBO 1

015 - 021

GOBO 2

022 - 028

GOBO 3

029 - 035

GOBO 4

036 - 042

GOBO 5

043 - 049

GOBO 6

050 - 056

GOBO 7

057 - 063

GOBO 8

064 - 071

GOBO 1 – Shaking

072 - 079

GOBO 2 – Shaking

080 - 087

GOBO 3 – Shaking

088 - 095

GOBO 4 – Shaking

096 - 103

GOBO 5 – Shaking

104 - 111

GOBO 6 – Shaking

112 - 119

GOBO 7 – Shaking

120 - 127

GOBO 8 – Shaking

128 - 189

Gobo wheel turning clockwise (fast → slow)

190 - 193

Gobo wheel stops turning

ENGLISH OPERATION MANUAL

BRITEQ

®

13/79 BTX-FALCON

194 - 255

Gobo wheel turning counter clockwise (slow → fast)

13

Prism on/off

000 - 127

Prism effect OFF

128 - 255

Prism effect ON

14

Prism - rotation

000 - 127

indexed positioning: 0° - 360°

128 - 189

Prism turning clockwise (fast → slow)

190 - 193

Prism stops turning

194 - 255

Prism turning counter clockwise (slow → fast)

15

000 - 255

Iris (maximum to minimum)

16

000 - 255

Focus (close to distant)

17

Special functions

000 - 069

No function

070 - 079

Activate blackout during pan/tilt (*)

080 - 089

Disable blackout during pan/tilt (*)

090 - 099

Activate blackout during color change (*)

100 - 109

Disable blackout during color change (*)

110 - 119

Activate blackout during gobo change (*)

120 - 129

Disable blackout during gobo change (*)

130 - 139

No function

140 - 149

Pan/tilt reset (*)

150 - 159

Color reset (*)

160 - 169

Gobo reset (*)

170 - 179

No function

180 - 189

Focus reset (*)

190 - 199

No function

200 - 209

Reset all (*)

210 - 219

Activate blackout during gobo/color or pan/tilt change (*)

220 - 229

Disable blackout during gobo/color or pan/tilt change (*)

230 - 255

No function

Note (*): function delay is set to 3seconds, the selected function will only be active while the corresponding

DMX-value is received during at least 3seconds.

ROTATING GOBOS (GOBO WHEEL1 – CHANNEL 10

Gobo wheel 1 contains 7 standard rotating gobos (gobo size: 26,8mm – image size: 22,0mm)

These gobos can be replace by your own custom gobos, both metal and glass gobos can be used.

Replacing the gobos:

 Switch the projector off, unplug the power cable and wait until the unit is cool.

 Remove the plastic cover of the head using a Phillips screwdriver (PH2)

 Locate the gobo wheel with rotating gobos.

 Each of the rotating gobos is mounted in a separate holder that can be easily removed from the wheel

just by lifting it up a little and tear it out.

 The gobo is fixed in the holder using a wire clip: remove the wire clip gently.

 Remove the gobo and replace it by a new one

 Put the wire clip back in place and click the holder back in the gobo wheel.

 Put the plastic cover of the head back in place using a Phillips screwdriver (PH2)

 Done.

ENGLISH OPERATION MANUAL

BRITEQ

®

14/79 BTX-FALCON

FIXED GOBOS (GOBO WHEEL2 – CHANNEL 12

Gobo wheel 2 contains 8 standard fixed gobos (gobo size: 31,4mm – image size: 22,0mm)

These gobos can be replace by your own custom gobos, only metal gobos can be used.

Replacing the gobos:

 Switch the projector off, unplug the power cable and wait until the unit is cool.

 Remove the plastic cover of the head using a Phillips screwdriver (PH2)

 Locate the gobo wheel with fixed gobos.

 The gobos are fixed directly in the gobo wheel.

 Remove the gobo gently and replace it by a new one.

 Put the plastic cover of the head back in place using a Phillips screwdriver (PH2)

 Done.

MAINTENANCE

 Make sure the area below the installation place is free from unwanted persons during servicing.

 Switch off the unit, unplug the mains cable and wait until the unit has been cooled down.

During inspection the following points should be checked:

 All screws used for installing the device and any of its parts should be tightly fastened and may not be

corroded.

 Housings, fixations and installations spots (ceiling, truss, suspensions) should be totally free from any

deformation.

 When an optical lens is visibly damaged due to cracks or deep scratches, it must be replaced.

 The mains cables must be in impeccable condition and should be replaced immediately when even a

small problem is detected.

 In order to protect the device from overheat the cooling fans and ventilation openings should be cleaned

monthly.

 The interior of the device should be cleaned annually using a vacuum cleaner or air-jet.

 The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to

optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp,

smoky or particularly dirty surroundings can cause greater accumulation of dirt on the unit’s optics.

 Clean with a soft cloth using normal glass cleaning products.

 Always dry the parts carefully.

Attention: We strongly recommend internal cleaning to be carried out by qualified personnel!

ENGLISH OPERATION MANUAL

BRITEQ

®

15/79 BTX-FALCON

SPECIFICATIONS

Mains Input: AC 100 - 240V, 50/60Hz

Power consumption: 330 Watt

Fuse: 250V 6,3A slow blow (20mm glass)

Power connections: Neutrik® PowerCON® - 16A Power linking capacity.

DMX connections: 3pin-XLR & 5pin-XLR male / female

DMX channels used: 17ch

Lamp: 180W LED Engine

Beam Angle: 16°

Color wheel 1: 7 colors + open

Color wheel 2: 8 colors, including CTO 3200K, CTO 5600K and UV

GOBO wheel 1: 7 rotating gobos, replaceable by metal and glass gobos

Outer diameter: 26,8mm – Image diameter: 22,0mm

GOBO wheel 2: 8 fixed gobos, replaceable only by metal gobos

Outer diameter: 31,4mm – Image diameter: 22,0mm

IP-Rating: IP20

Operating temperature (T

a

): 0°C to 40°C

Installation: 2 quarter turn quick clamps

Size: see drawing below

Weight: 17,5 kg

The information might be modified without prior notice

You can download the latest version of this user manual on our website: www.briteq-lighting.com

FRANÇAIS GUIDE D'UTILISATION

BRITEQ

®

16/79 BTX-FALCON

GUIDE D'UTILISATION

Nous vous remercions d'avoir acheté ce produit BRITEQ. Pour tirer pleinement profit de toutes les

possibilités et pour votre propre sécurité, lisez ces instructions très attentivement avant d'utiliser cet appareil.

CARACTÉRISTIQUES

Cet appareil ne produit pas d'interférences radio. Ce produit répond aux exigences des directives européennes

et nationales actuelles. La conformité a été établie et les déclarations et documents correspondants ont été

déposés par le fabricant.

 Une lyre très lumineuse contrôlée par un module à LED tout neuf et puissant de 180W !

 100% compatible avec notre fameuse BTX-180LS mais avec 40% plus de puissance lumineuse!

 L'utilisation d'optique de pointe 16° permet de produire une lumière incroyablement forte : 221’700 lux @ 1m

 Idéal pour les entreprises de location, scènes, discothèques, etc.

 Les mouvements pan/tilt (540°/270°) très rapides assurent une programmation de spectacle très dynamique.

 Résolution pan/tilt 8 ou 16 bits avec correction de position X/Y et canal de vitesse.

 Les 17 canaux DMX offrent un grand nombre de possibilités et caractéristiques :

 Netteté contrôlée électroniquement par DMX

 Diaphragme contrôlé par DMX

 2 roues de gobos pour des beaux effets de gobos superposés :

 7 gobos rotatifs rapides + ouvert

 8 gobos fixes + ouvert

 2 roues de couleur, chacune avec 7 couleurs dichroïques soigneusement sélectionnées + ouvert

 Gradateur/obturateur électronique extrêmement rapide

 Prisme à 3 facettes à rotation rapide pour les effets spéciaux

 Différents effets stroboscopiques

 Canal d'effets : Allumage/Extinction de lampe à distance, différentes fonctions d'obscurcissement, etc.

 Fonctionne également en mode autonome et maître/esclave : les shows préprogrammés sont déclenchés

par le micro interne.

 Entrées/sorties Neutrik PowerCon

®

: chaînage facile de plusieurs unités jusqu'à 16A.

 Entrées/sorties Neutrik 3 et 5 broches pour un maximum de flexibilité dans un environnement professionnel

 Les mises à jour faciles du micrologiciel permettent de maintenir votre appareil à jour en permanence (un

module de mise à jour optionnel est nécessaire)

 L'écran LCD à matrice assure une navigation facile à travers les différents menus de configuration

 Haut rendement et faible consommation d'énergie, uniquement 245 Watts

 Equipé de supports Omega pour une installation rapide

AVANT UTILISATION

 Avant d'utiliser cet appareil, vérifiez s'il n'a pas été endommagé durant le transport. En cas de dommages,

n'utilisez pas l'appareil et consultez immédiatement votre revendeur.

 Important : Cet appareil est expédié de notre usine en parfait état et bien emballé. Il est absolument

nécessaire que l'utilisateur suive strictement les instructions et les avertissements de sécurité se trouvant

dans ce manuel. Tout dommage dû à une mauvaise manipulation n'est pas garanti. Le revendeur

n'accepte aucune responsabilité pour tous les défauts et problèmes dus au non-respect de ce manuel.

 Conservez ce manuel dans un endroit sûr pour toute consultation future. Si vous vendez l'appareil, veillez

à joindre ce manuel.

Vérifiez le contenu :

Vérifiez que le carton contient les éléments suivants :

 Instructions d'utilisation

 Lyre BTX-FALCON

 2 attaches rapides « Omega »

 Câble PowerCon

®

FRANÇAIS GUIDE D'UTILISATION

BRITEQ

®

17/79 BTX-FALCON

INSTRUCTIONS DE SÉCURITÉ :

 Pour protéger l'environnement, essayer de recycler autant que possible les matériaux d'emballage.

 Pour éviter tout incendie ou électrocution, n'exposez pas cet appareil à la pluie ou l'humidité.

 Pour éviter une formation de condensation interne, laissez l'appareil s'adapter à la température ambiante

quand vous le mettez dans une pièce chaude après le transport. La condensation empêche parfois

l'appareil de fonctionner à plein rendement ou peut même causer des dommages.

 Cet appareil est destiné à un usage intérieur seulement.

 Ne placez pas d'objets métalliques et ne renversez pas de liquides à l'intérieur de l'appareil. Un choc

électrique ou un dysfonctionnement peut en résulter. Si un corps étranger pénètre dans l'appareil,

débranchez immédiatement le cordon d'alimentation de la prise secteur.

 Placez l'appareil dans un endroit bien aéré, loin de tout matériau et/ou liquide inflammable. L'appareil doit

être fixé à au moins 50cm des murs environnants.

 Ne couvrez pas les ouvertures de ventilation, cela pourrait entraîner une surchauffe.

 Évitez une utilisation dans des environnements poussiéreux et nettoyez l'appareil régulièrement.

 Gardez l'appareil loin de la portée des enfants.

 Les personnes inexpérimentées ne doivent pas utiliser cet appareil.

 La température ambiante de fonctionnement maximale est de 40°C. N'utilisez pas cet appareil à des

températures ambiantes plus élevées.

 Assurez-vous qu'aucune personne étrangère ne se trouve dans la zone en dessous de l'emplacement

d'installation durant le montage, le démontage et l'entretien.

 Laissez environ 10 minutes à l'appareil pour refroidir avant de commencer l'entretien.

 Débranchez toujours l'appareil lorsqu'il ne va pas être utilisé pendant une longue période ou avant de

commencer l'entretien.

 L'installation électrique doit être effectuée par du personnel qualifié, conformément à la réglementation en

matière de sécurité électrique et mécanique dans votre pays.

 Vérifiez que la tension secteur n'est pas supérieure à celle indiquée sur l'appareil.

 Le cordon d'alimentation doit toujours être en parfait état. Éteignez immédiatement l'appareil dès que le

cordon d'alimentation est écrasé ou endommagé. Il doit être remplacé par le fabricant, son agent de

service ou une personne de même qualification afin d'éviter tout danger.

 Ne laissez jamais le cordon d'alimentation ENTRER en contact avec d'autres câbles !

 Ce luminaire doit être mis à la terre pour être conforme réglementation en matière de sécurité.

 Ne connectez pas l'appareil à un variateur de lumière.

 Utilisez toujours un câble de sécurité approprié et certifié lors de l'installation de l'appareil.

 Afin d'éviter un choc électrique, n'ouvrez aucun panneau. L'appareil ne contient aucun composant

réparable par l'utilisateur.

ATTENTION : Pour réduire le risque de choc électrique, ne

retirez pas le panneau supérieur. L'appareil ne contient aucun

composant réparable par l'utilisateur. Confiez toute réparation à

un personnel qualifié uniquement.

Le symbole de l'éclair à l'intérieur d'un triangle équilatéral, est destiné à alerter l'utilisateur de la

présence de « tensions dangereuses » non isolées à l'intérieur de l'appareil, d'une magnitude

pouvant constituer un risque d'électrocution.

Le symbole du point d'exclamation dans un triangle équilatéral sert à avertir l'utilisateur que

d'importants conseils d'utilisation et de maintenance sont fournis dans la documentation

accompagnant l'appareil.

Ce symbole signifie : pour usage intérieur uniquement.

Ce symbole signifie : Lisez les instructions.

Ce symbole détermine : la distance minimale requises avec les objets éclairés. La distance

minimale entre la sortie de lumière et la surface éclairée doit être supérieure à 2 mètres.

Cet appareil n'est pas adapté pour un montage direct sur des surfaces normalement

inflammables. (ne convient que pour le montage sur surfaces non combustibles)

ATTENTION : Ne fixez pas votre regard sur une lampe allumée.

Peut être nocif pour les yeux.

FRANÇAIS GUIDE D'UTILISATION

BRITEQ

®

18/79 BTX-FALCON

 Ne réparez jamais un fusible et ne court-circuitez jamais le porte-fusible. Remplacez toujours un fusible

endommagé par un fusible du même type ayant les mêmes spécifications électriques !

 En cas de sérieux problèmes de fonctionnement, cessez d'utiliser l'appareil et contactez immédiatement

votre revendeur.

 Le boîtier et l'objectif doivent être remplacés s'ils sont visiblement endommagés.

 Utilisez l'emballage d'origine pour transporter l'appareil.

 Pour des raisons de sécurité, il est interdit d'apporter des modifications non autorisées à l'appareil.

Important : Ne regardez jamais directement la source de lumière ! N'utilisez pas le jeu de lumière en

présence de personnes souffrant d'épilepsie.

DESCRIPTION :

PANNEAU DE COMMANDE :

1. Témoins d'état : témoins utilisés pour indiquer l'état du projecteur.

DMX

Marche

présence d'entrée DMX, clignote pendant la mise à jour du

logiciel

MASTER

Marche

le projecteur fonctionne en mode maître

SLAVE

Marche

le projecteur fonctionne en mode esclave

SOUND

Clignotant

Indique une activité audio

2. L'écran : affiche les différents menus et les fonctions sélectionnées.

3. TOUCHES DE NAVIGATION :

MENU

Permet d'accéder au menu configuration ou de retourner à une fonction

précédente

BAS

Permet de descendre dans l'arborescence des menus

HAUT

Permet de remonter dans l'arborescence des menus

ENTER

Pour confirmer les fonctions sélectionnées

Deux touches raccourcis facilitent le travail de l'installateur :

 Appuyez sur Haut et Bas en même temps : Permet de faire pivoter l'affichage de 180°.

 Maintenez appuyées MENU + ENTER pendant 3 secondes : le projecteur retrouve sa position

initiale.

4. Attache Omega : vous pouvez utiliser l'attache rapide « oméga » incluse en dessous de l’appareil. Il

suffit de faire pivoter le système de verrouillage sur 90° pour fixer l'attache. Utilisez toujours un câble de

sécurité pour plus de sécurité !

5. ENTREES/SORTIES DMX : utilisé pour des configurations en DMX512, vous pouvez utiliser des câbles

de signaux symétriques de bonne qualité avec connecteurs XLR 3 ou 5 broches.

6. FUSIBLE SECTEUR : ce fusible ne protège que la partie électronique du projecteur, l'entrée/sortie (7)

secteur n'est pas protégée par fusible.

7. ENTRÉE ET SORTIE SECTEUR : Utilisez les prises POWERCON

®

pour brancher le câble

d'alimentation fourni ici ; vous pouvez connecter en série plusieurs unités, jusqu'à 16A maximum. Aucun

fusible n'est utilisé au niveau des entrées et sorties raccordées.

Astuce : Veuillez consulter notre site Web pour les assemblages de câbles spéciaux qui offrent une

puissance (3x1,5mm² avec Neutrik PowerCon

®

) et un signal symétrique (XLR 3 broches) dans un seul câble.

Différentes longueurs sont disponibles : 1,3m, 3m, 5m et 10m, très pratiques !

La page charge ...

Briteq BTX-FALCON Le manuel du propriétaire

Briteq BTX-FALCON Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents