EarthQuake RC4432 Mode d'emploi

Marque: EarthQuake

Modèle: RC4432

Catégorie: Tondeuses à gazon

Taper: Mode d'emploi

Ce manuel convient également à

RC4432 MOWER ROUGH CUT 44 INCH BRIGGS

GAS/OIL

RATIO

50:1

SERIAL NO.

N° DE SÉRIE

DATE OF PURCHASE:

DATE D’ACHAT:

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.

CE LIVRET D’INSTRUCTIONS CONTIENT DES INFORMATIONS IMPORTANTES SUR LA SÉCURITÉ. VEUILLEZ LE LIRE ET LE CONSERVER POUR TOUTE CONSULTATION EXTÉRIEURE.

Owner’s Manual

Manuel de l’utilisateur

ACREAGE™

Rough Cut Mower

Faucheuse tractée

Model #’s: RC4432

Modèles n°: RC4432

Get parts or technical assistance online at

www.GetEarthquake.com or call (800) 345-6007

Pièces détachées et assistance technique en ligne à

www.GetEarthquake.com ou composer le (800) 345-6007

P/N: 29890

Réf.: 12645

REV 2: 10/29/2019

RÉV 2: 2019-10-29

ENGLISHFRANÇAIS

Owner’s Manual

ACREAGE™ ROUGH CUT MOWER

Get parts online at www.GetEarthquake.com or Call 800-345-6007 M-F 8-5 CST

INTRODUCTION

Thank you for purchasing your product from Earthquake®. We have worked to ensure that this product meets the highest

standards for usability and durability. With proper care, your purchase will provide many years of service.

Please read this entire manual before installation and use. Earthquake® reserves the right to change, alter or improve the product

and this document at any time without prior notice. Due to continuous product improvements, product images may not be exact.

Some assembly may be required.

Read and keep this manual for future reference. This manual contains important information regarding safety, assembly, operation

and maintenance. The owner must be certain that all the product information is included with the unit. This information includes

the manual, the replacement parts and the warranties. This information must be included to make sure state laws and other laws

are followed. All persons to whom rent/loan this unit must have access to and understand this information. This manual should

remain with the product even if it is resold.

CONTENTS

Introduction/Contents ..................................................................................................................................................................................................................2

Bolt Identication Chart ................................................................................................................................................................................................................3

Warnings and Safety Precautions ..........................................................................................................................................................................................4-9

Features ............................................................................................................................................................................................................................................10

Assembly ................................................................................................................................................................................................................................... 11-12

Operation .................................................................................................................................................................................................................................. 12-15

Maintenance and Storage ................................................................................................................................................................................................... 15-17

Troubleshooting and Repair ......................................................................................................................................................................................................17

STOP! ACTIVATE YOUR WARRANTY BEFORE USE

All products must be registered within 30 days from the date of purchase in order to be covered under

warranty. For more information regarding Warranty and Registration please review the Warranty and

Registration terms and conditions expressed in the warranty insert.

REGISTRATION AND SERVICE

Record the product model number and serial number in the

space provided for easy reference when ordering parts or

requesting technical support. Excluding emissions-related

warranty items, the warranty is valid only if the completed

registration is received by Ardisam within 30 days of

purchase. You can register your warranty online by visiting

www.GetEarthquake.com, or by mailing it to: Ardisam, 1160

8th Avenue, Cumberland, WI 54829. You may also call our

Customer Service department at (800) 345-6007 Mondays

through Fridays from 8 a.m. to 5 p.m. CST.

Serial Number

Location

Owner’s Manual

ACREAGE™ ROUGH CUT MOWER

Get parts online at www.GetEarthquake.com or Call 800-345-6007 M-F 8-5 CST

HARDWARE IDENTIFICATION CHART

Bolts shown are for size reference only. Extra hardware may be

included in the parts bag.

(A)

6.35mm x 45mm long

Qty. = 2

(B)

M12 x 64mm long

Qty. = 1

(C)

Shaft Cap

Qty. = 2

Owner’s Manual

ACREAGE™ ROUGH CUT MOWER

Get parts online at www.GetEarthquake.com or Call 800-345-6007 M-F 8-5 CST

NOTICE

NOTICE INDICATES YOUR EQUIPMENT CAN BE DAMAGED

IF THE SAFETY INSTRUCTIONS THAT FOLLOW THIS SIGNAL

WORD ARE NOT OBEYED.

WARNINGS AND SAFETY PRECAUTIONS

OWNER’S RESPONSIBILITY

Accurate assembly and safe and eective use of the machine is

the owner’s responsibility.

• Read and follow all safety instructions.

• Carefully follow all assembly instructions.

• Maintain the machine according to directions and

schedule included in this Earthquake® operator’s manual.

• Ensure that anyone who uses the machine is familiar with

all controls and safety precautions.

SPECIAL MESSAGES

Your manual contains special messages to bring attention to

potential safety concerns, machine damage as well as helpful

operating and servicing information. Please read all the

information carefully to avoid injury and machine damage.

NOTE: General information is given throughout the manual

that may help the operator in the operation or service of the

machine.

This symbol points out important safety instructions

which if not followed could endanger your personal safety.

Read and follow all instructions in this manual before

attempting to operate this equipment.

BEFORE OPERATING EQUIPMENT:

Please read this section carefully. Read entire operating and

maintenance instructions for this product. Failure to follow

instructions could result in serious injury or death. Operate the

machine according to the safety instructions outlined here and

inserted throughout the text. Anyone who uses this machine

must read the instructions and be familiar with the controls.

CAUTION

CAUTION INDICATES A HAZARD WHICH, IF NOT AVOIDED,

COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY

DAMAGE.

WARNING

WARNING INDICATES A HAZARD WHICH, IF NOT AVOIDED,

COULD RESULT IN DEATH OR SERIOUS INJURY AND/OR

PROPERTY DAMAGE.

DANGER

DANGER INDICATES A HAZARD WHICH, IF NOT AVOIDED,

CERTAINLY WILL RESULT IN DEATH OR SERIOUS INJURY

AND/OR PROPERTY DAMAGE.

IMPORTANT

IMPORTANT INDICATES HELPFUL INFORMATION FOR

PROPER ASSEMBLY, OPERATION OR MAINTENANCE OF

YOUR EQUIPMENT.

WARNING

YOU MUST READ, UNDERSTAND AND COMPLY WITH ALL

SAFETY AND OPERATING INSTRUCTIONS IN THIS MANUAL

BEFORE ATTEMPTING TO SETUP AND OPERATE YOUR

MACHINE.

FAILURE TO COMPLY WITH ALL SAFETY AND OPERATING

INSTRUCTIONS CAN RESULT IN LOSS OF MACHINE

CONTROL, SERIOUS PERSONAL INJURY TO YOU AND/OR

BYSTANDERS, AND RISK OF EQUIPMENT AND PROPERTY

DAMAGE. THE TRIANGLE IN THE TEXT SIGNIFIES

IMPORTANT CAUTIONS OR WARNINGS WHICH MUST BE

FOLLOWED.

Owner’s Manual

ACREAGE™ ROUGH CUT MOWER

Get parts online at www.GetEarthquake.com or Call 800-345-6007 M-F 8-5 CST

WARNING

CALIFORNIA PROPOSITION 65 WARNING

ENGINE EXHAUST FROM THIS PRODUCT CONTAINS

CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE

CANCER, BIRTH DEFECTS, OR OTHER REPRODUCTIVE HARM.

GENERAL SAFETY RULES

• Read, understand, and follow all instructions on the

machine and in the manual(s). Be thoroughly familiar

with the controls and the proper use of the mower before

starting.

• Familiarize yourself with all of the safety and operating

decals on this equipment and on any of its attachments or

accessories.

• Do not put hands or feet near or under rotating parts.

• Only allow responsible individuals, who are familiar with

the instructions, to operate the mower.

• Thoroughly inspect the area where the machine is to be

used and remove all foreign objects. Your equipment can

propel small objects at high speed causing personal injury

or property damage. Stay away from breakable objects,

such as house windows, automobile, greenhouses, etc.

• Keep the area of operation clear of all persons, particularly

small children, and pets.

• Wear appropriate clothing such as a long-sleeved shirt

or jacket. Also wear long trousers or slacks. Do not wear

shorts.

• Do not wear loose clothing or jewelry. They can get

caught in moving parts.

• Always wear safety goggles or safety glasses with side

shields when operating mower to protect your eyes from

foreign objects which can be thrown from the unit.

• Always wear work gloves and sturdy footwear. Wear

footwear that will improve footing on slippery surfaces.

Leather work shoes or short boots work well for most

people. These will protect the operator’s ankles and shins

from small sticks, splinters, and other debris.

• It is advisable to wear protective headgear to prevent

the possibility of being struck by small ying particles,

or being struck by low hanging branches, twigs, or other

objects which may be unnoticed by the operator.

• Do not operate the mower without proper guards or other

safety protective devices in place.

• Use this equipment for its intended purpose only.

• See manufacturer’s instructions for proper operation and

installation of accessories. Only use accessories approved

by the manufacturer.

• Operate only in daylight or good articial light.

• Do not operate product when fatigued or under the

inuence of alcohol, drugs or other medication which

can cause drowsiness or aect your ability to operate this

machine safely.

• Never operate mower in wet grass. Always be sure of your

vehicle’s traction; keep a steady pace and do not exceed

the recommended maximum speed in this manual.

• Stop the rotating mower head when crossing gravel

drives, walks, or roads. Wait for the cutting blades to stop

rotating.

• Watch for trac when operating near, or when crossing

roads.

• Stop the engine (motor) whenever you leave the

equipment, before cleaning, repairing or inspecting

the unit, be sure the mower and all moving parts have

stopped. Let the engine cool, disconnect the spark plug

wire, move it away from the spark plug and remove the

ignition key.

• If the equipment should start to vibrate abnormally,

stop the engine (motor), disconnect the spark plug wire,

prevent it from touching the spark plug and remove the

ignition key. Check immediately for cause. Vibration is

generally a symptom of a larger issue.

• After striking a foreign object, stop the engine (motor).

Remove the wire from the spark plug and remove the

ignition key. Inspect the mower for damage. If damaged,

repair before starting and operating the mower.

• Never leave the mower unattended when the engine is

running.

• Regularly inspect the mower. Make sure parts are not

bent, damaged or loose.

• Allow muer and engine areas to cool before touching.

• Never operate or have engine running without having

mower attached to suitable tow vehicle.

Owner’s Manual

ACREAGE™ ROUGH CUT MOWER

Get parts online at www.GetEarthquake.com or Call 800-345-6007 M-F 8-5 CST

• Prolonged exposure to noise and vibration from gasoline

engine powered equipment should be avoided. Take

intermittent breaks and/or wear ear protection from

engine noise.

• Check local regulations for age restrictions on use of this

machine.

• If the noise or vibrations of the machine increase, stop

immediately and perform an inspection.

• The fuel used in this machine is considered extremely

ammable and should be handled with care. When storing

extra fuel be sure that it is in an appropriate container and

away from any re hazards.

SLOPE OPERATION

• Slopes are a major factor related to slip-and-fall or roll-

over accidents which can result in severe injury. All slopes

require extra caution. If you feel uneasy on a slope, do not

mow it. Do mow up and down; never across the face of

slopes. Do not mow excessively steep slopes (maximum

20 degrees) or areas where the ground is very rough. See

the “Slope Guide” in the back of this manual to check a

slope. Exercise extreme caution when changing direction

on slopes.

• Remove objects such as rocks, tree limbs, etc.

• Watch for holes, ruts, or bumps. Tall grass can hide

obstacles.

IMPORTANT NOTES:

Do not mow near drop-os, ditches, or embankments.The

towing vehicle could lose traction or balance.

Do not mow excessively steep slopes.

Do not mow on wet grass. Reduced traction could cause

slipping or roll-over. Wet piles of grass can also cause re due

to spontaneous combustion.

CHILDREN

Tragic accidents can occur if the operator is not alert to the

presence of children. Children are often attracted to the

mower and the mowing activity. Never assume that children

will remain where you last saw them.

• Keep children out of the mowing area and under the

watchful care of a responsible adult that is not performing

mower operation.

• Be alert and turn mower o if children enter the area.

• Before and while moving backwards, look behind and

down for small children.

• Never allow children to operate the mower or be a

passenger on the tow vehicle.

• Use extra care when approaching blind corners, shrubs,

trees, or other objects that may obscure vision.

SERVICE

• Use extra care in handling gasoline and other fuels. They

are ammable and vapors are explosive.

• Use only an approved container.

• Never remove gas cap or add fuel with the engine

running. Allow engine to cool before refueling. Do not

smoke while refueling.

• Fill fuel tank outdoors with extreme care. Never ll fuel

tank indoors or near appliances with pilot lights, heaters,

or other ignition sources. Replace fuel cap securely. If fuel

is spilled, do not start the engine but move product and

fuel container from area. Clean up spilled fuel and allow to

evaporate.

• Never store the machine or fuel container inside where

there is an open ame (such as a water heater), or other

ignition source.

• If the fuel has to be drained, this should be done

outdoors. The drained fuel should be stored in a container

specically designed for fuel storage or it should be

disposed of carefully and according to local regulations.

• Engines give o carbon monoxide, an odorless, colorless,

poison gas. Breathing carbon monoxide can cause nausea,

fainting or death. Always start and run engine outdoors.

Do not start or run engine in an enclosed area, even if

doors or windows are open.

• Never make adjustments or repairs with the engine

(motor) running. Disconnect the spark plug wire, keep the

wire away from the plug to prevent accidental starting,

and remove the ignition key. Always wear eye protection

when you make adjustments or repairs.

• Check the mower head and engine mounting bolts at

frequent intervals for proper tightness.

• Keep all nuts and bolts tight and keep equipment in good

condition. Check mounting hardware on mower prior to

each use.

Owner’s Manual

ACREAGE™ ROUGH CUT MOWER

Get parts online at www.GetEarthquake.com or Call 800-345-6007 M-F 8-5 CST

ENGINE SAFETY PRECAUTIONS

If your product comes with a separate engine manual, be sure

to read and follow all safety and warning precautions outlined

there, in addition to any in this manual.

PREVENTING CARBON MONOXIDE POISONING

• Always start and run engine outdoors. Do not start or run

engine in an enclosed area, even if doors or windows are

open.

• Never try to ventilate engine exhaust indoors. Carbon

monoxide can reach dangerous levels very quickly.

• Never tamper with safety devices. Check their proper

operation regularly.

• When servicing or repairing the mower, do not tip the

machine over or up unless specically instructed to do so

in this manual. Service and repair procedures can be done

with the mower in an upright position. Some procedures

will be easier if the machine is lifted on a raised platform

or working surface.

• To reduce re hazard, keep mower free of grass, leaves, or

other debris build-up. Clean up oil or fuel spillage. Allow

mower to cool before storing.

• Stop and inspect the equipment if you strike an object.

Repair, if necessary, before restarting.

• Always disconnect spark plug wire and remove the

ignition key before cleaning, repairing, or adjusting.

• Do not change the engine governor setting or over-speed

the engine.

• Clean and replace safety and instruction decals as

necessary.

• To guard against engine over-heating, always have engine

debris lter mounted and clean.

• Inspect cooling ns on engine.

• Inspect mower before storage. When not in use,

disconnect spark plug lead, remove ignition key and store

indoors in a dry place locked or otherwise inaccessible to

children.

• Use only original equipment or authorized replacement

parts.

• Always follow the manufacturers instructions on operation

of the tow vehicle.

• Never run engine outdoors where exhaust fumes may be

pulled into a building.

• Never run engine outdoors in a poorly ventilated area

where the exhaust fumes may be trapped and not easily

taken away. (Examples include: in a large hole or areas

where hills surround your working area.)

• Never run engine in an enclosed or partially enclosed area.

(Examples include: buildings that are enclosed on one or

more sides, under tents, car ports or basements.)

• Always run the engine with the exhaust and muer

pointed in the direction away from the operator.

• Never point the exhaust muer towards anyone. People

should always be many feet away from the operation of

the engine and its attachments.

• Do not change the engine governor settings or over-

speed the engine.

SAFE HANDLING OF GASOLINE

Use extra care in handling gasoline and other fuels. They are

extremely ammable and vapors are explosive.

• Extinguish all cigarettes, cigars, pipes and other sources of

ignition.

• Never remove gas cap or add fuel with the engine

running.

• Allow engine to cool before refueling.

• Never store the machine or fuel container where there

is an open ame, spark, or pilot light such as on a water

heater or on other appliances.

• Never ll containers inside a vehicle or on a truck or trailer

bed with a plastic liner. Always place containers on the

ground away from your vehicle before lling.

• Remove gas powered equipment from the truck or trailer

and refuel it on the ground. If this is not possible, then

refuel such equipment with a portable container, rather

than from a gasoline dispenser nozzle.

• Keep the nozzle in contact with the rim of the fuel tank or

container opening at all times until fueling is complete. Do

not use a nozzle lock open device.

• If fuel is spilled on clothing, change clothing immediately.

• Never overll fuel tank. Replace gas cap and tighten

securely.

Owner’s Manual

ACREAGE™ ROUGH CUT MOWER

Get parts online at www.GetEarthquake.com or Call 800-345-6007 M-F 8-5 CST

• If fuel is spilled do not attempt to start the engine but

move the machine away from the area of spillage and

avoid creating any source of ignition until fuel vapors have

dissipated.

• Prevent re and explosion caused by static electric

discharge. Use only nonmetal, portable fuel containers

approved by the Underwriter’s Laboratory (U.L.) or the

American Society for Testing & Materials (ASTM).

• Always ll fuel tank outside in a well ventilated area. Never

ll your fuel tank with fuel indoors. (Examples include:

basement, garage, barn, shed, house, porch, etc.).

• Test the fuel cap for proper installation before starting and

using engine.

• Always run the engine with fuel cap properly installed on

the engine.

Owner’s Manual

ACREAGE™ ROUGH CUT MOWER

Get parts online at www.GetEarthquake.com or Call 800-345-6007 M-F 8-5 CST

SAFETY DECALS AND WARNINGS

Pictured below are safety and hazard symbols on the unit

or in this manual. Before you operate your unit, learn and

understand the purpose for each symbol.

A B C

D E

Hazard Symbols and Meanings

a: Warning!

b: Read Owner's Manual Before Operating Machine

c: Keep Hands Clear, Contact Can Injure

d: Keep Feet Clear, Contact Can Injure

e: Go Up And Down Slopes, Not Across Slopes Sideways

f: Remove Objects That Could Be Thrown By The Blade

Should any of the safety labels become unreadable because

of being worn, faded, or otherwise damaged during the use of

your mower, please use the part number information provided

to order a replacement label.

Part Number: 21430

Decal Mower Warnings

Part Number: 21429

Decal Danger Keep Hands And Feet Away

Part Number: 21432

Decal Caution Do Not Exceed 5 MPH

Part Number: 21433

Decal Danger Spinning Blades

Owner’s Manual

ACREAGE™ ROUGH CUT MOWER

Get parts online at www.GetEarthquake.com or Call 800-345-6007 M-F 8-5 CST

FEATURES

Read this owner's manual and safety rules before operating your mower. Take time to compare the following illustration with the

mower to familiarize yourself with the product and its controls. SEE FIGURE 12

FIGURE 12: RC4432 ROUGH CUT MOWER FEATURES

KEY FEATURE

1 TOOLLESS ADJUSTABLE TANDEM TOWBAR 9 TOWING POSITIONS

2 TOWBAR LOCKING PIN

3 FRONT AND REAR CHAIN GUARDS

4 KEY START IGNITION *ON BACK OF UNIT

5 BLADE CONTROL LEVER

6 TOOLLESS STEPANDDROP WHEEL ADJUSTERS 5 POSITIONS

7 1.72 GALLON FUEL TANK

KEY FEATURE

8 FUEL PUMP

9 OIL FILL PORT

10 500CC ELECTRIC START BRIGGS & STRATTON

ENGINE

11 EXHAUST MUFFLER

12 BATTERY

13 WHEEL BRUSH GUARD

14 MANUAL CANISTER

FIGURE 12

Owner’s Manual

ACREAGE™ ROUGH CUT MOWER

Get parts online at www.GetEarthquake.com or Call 800-345-6007 M-F 8-5 CST

ASSEMBLY

Tools Required:

• Wrenches

• Tire Pressure Gauge

• Sidecutter or Industrial Scissors

• Safety Goggles and Gloves

• ATV/UTV

Remove the Mower from the Shipping Crate:

1. Remove any loose parts or packaging, from the crate. SEE

FIGURE 3

2. Remove the bolts securing the sections of the container

together, cut all zip ties and disassemble shipping crate.

3. Raise the cutter deck to its highest height position (see

cutter height adjustment on Page 13) to clear the crate. The

mower can now be rolled o the shipping crate.

4. Remove any additional packaging material and inspect

the mower.

5. Assemble the adjustable tandem tow draw bar to the

mower using included hardware.

NOTE: Refer to the Illustrated Parts Breakdown for part

identication and location.

ENGINE PREPARATION

See the engine manufacturer’s instructions for the type of

gasoline and oil to use. Before you use the unit, read the

information on safety, operation, maintenance, and storage.

Fill Crankcase With Oil

See engine manual for oil ll instructions.

Fill Fuel Tank With Gasoline

See the engine manufacturer’s instructions for the type of

gasoline to use.

BATTERY PREPARATION

The Rough Cut Mower is supplied with a 12 volt, maintenance

free lead acid battery. When the battery is properly maintained

and charged, it will provide years of dependable service.

1. The Rough Cut Mower is shipped with the negative

battery terminal disconnected. This is to prevent battery

discharge while in shipping. If necessary, connect the

terminal and charge the battery.

FIGURE 3: YOUR NEW MOWER AS IT IS SHIPPED TO YOU

WARNING

CAUTION

USE THE CORRECT PERSONAL PROTECTION. WEAR

SAFETY GLASSES OR FACE SHIELDS WHILE ASSEMBLING OR

OPERATING THE MOWER.

BE CAREFUL OF SHARP EDGES. THE CUTTER BLADE ASSEMBLY

CAN ROTATE AS THE DECK IS MANEUVERED. WEAR GLOVES

WHEN HANDLING THE MOWER DECK AND CUTTER BLADES.

REMOVE SPARK PLUG WIRE FROM SPARK PLUG AND KEY FROM

IGNITION BEFORE DOING ANY ASSEMBLY OR MAINTENANCE

TO THE MOWER.

TWO MAN LIFT REQUIRED. THE RC4432 MOWER WEIGHS 675

LBS. DO NOT TRY TO LIFT ALONE.

USE THE CORRECT PERSONAL PROTECTION. GASOLINE

AND ENGINE OIL ARE HAZARDOUS TO YOUR HEALTH.

ALWAYS USE A SAFETY APPROVED GASOLINE CONTAINER.

DO NOT SMOKE WHEN ADDING GASOLINE TO THE ENGINE.

DO NOT FILL WITH GASOLINE WHEN INSIDE AN ENCLOSURE.

ALWAYS MOVE OUTDOORS WHERE FUEL VAPORS WILL NOT

COLLECT.

THE ENGINE AND MUFFLER CAN BE VERY HOT AND CAUSE

BURNS. BEFORE YOU ADD GASOLINE, STOP THE ENGINE. LET

THE ENGINE COOL FOR SEVERAL MINUTES.

ENGINE DOES NOT CONTAIN OIL OR GASOLINE WHEN

SHIPPED FROM THE FACTORY. YOU MUST SERVICE THE

ENGINE BEFORE OPERATION.

FOLLOW THE ENGINE MANUFACTURER’S INSTRUCTIONS FOR

THE TYPE OF GASOLINE AND OIL TO USE.

Owner’s Manual

ACREAGE™ ROUGH CUT MOWER

Get parts online at www.GetEarthquake.com or Call 800-345-6007 M-F 8-5 CST

MAKE SURE YOU READ AND UNDERSTAND THE

OPERATORS MANUAL BEFORE ATTEMPTING TO OPERATE

THIS MACHINE. KNOW HOW TO QUICKLY SHUT DOWN

THE MOWER AND TOW VEHICLE BEFORE ATTEMPTING

TO OPERATE THIS MACHINE.

BE CAREFUL AROUND MOVING PARTS. THE MOWER

HEAD WILL CONTINUE TO ROTATE FOR SEVERAL

SECONDS AFTER THE ENGINE HAS STOPPED.

DO NOT ATTEMPT TO CRANK OR START THE ENGINE

BEFORE IT HAS BEEN PROPERLY SERVICED WITH THE

RECOMMENDED OIL. THIS MAY RESULT IN AN ENGINE

FAILURE.

DO NOT MODIFY, REMOVE, CUT, BEND, OR WELD

THE PARTS OF THE MOWER OR THE SHIELD GUARDS.

MODIFICATION OF YOUR MACHINE WILL VOID YOUR

WARRANTY AND CAN CAUSE PROPERTY DAMAGE,

SERIOUS INJURY AND/OR DEATH.

ALWAYS BE AWARE OF THE MOWER POSITION. THE

MOWER CAN BE TOWED AT AN OFF SET AND MAY NOT

ALWAYS BE DIRECTLY BEHIND THE TOW VEHICLE.

WHEEL PREPARATION

Use a tire pressure gauge to check the tire pressure. Fill tires to

a maximum of 28 psi.

USE THE CORRECT PERSONAL PROTECTION. BATTERY

CONTAINS SULFURIC ACID AND IS CORROSIVE. YOU

MUST WEAR SAFETY GOGGLES AND GLOVES WHEN

SERVICING THE BATTERY.

DO NOT DROP THE BATTERY. BATTERY IS HEAVY AND CAN

CAUSE DAMAGE TO EQUIPMENT OR CAUSE PERSONAL

INJURY IF DROPPED.

USE THE CORRECT CHARGER AND ALWAYS INSPECT

THE BATTERY AND TERMINALS FOR DAMAGE OR WEAR.

REPLACE ANY DAMAGED OR WORN ITEMS.

DO NOT LIFT OR CARRY THE BATTERY BY THE TERMINALS

OR CABLES. DO NOT SHORT CIRCUIT THE BATTERY

TERMINALS. DAMAGE TO THE BATTERY OR FIRE CAN

OCCUR. SERIOUS INJURY OR DEATH CAN RESULT.

IF DURING OPERATION THE MOWER MAKES UNUSUAL

NOISES OR VIBRATIONS, SHUT OFF THE TOW VEHICLE

THEN SHUT OFF THE ROUGH CUT MOWER ENGINE. WAIT

FOR THE ENGINE AND MOWER PARTS TO COOL. REMOVE

THE SPARK PLUG AND KEY FROM IGNITION BEFORE

INSPECTING THE MOWER.

INSPECT MOWER FOR LOOSE, WORN, DAMAGED,

OR MISSING HARDWARE. REPAIR OR REPLACE ANY

DAMAGED PARTS BEFORE OPERATION OF THE MOWER.

ALWAYS USE APPROVED REPLACEMENT PARTS AND

HARDWARE.

CLEAR ALL OBSTRUCTIONS FROM THE MOWER DECK,

AIR FILTER, AND EXHAUST MUFFLER AREAS.

MOWER BLADES ARE SHARP. MAKE SURE YOU WRAP THE

BLADES OR USE GLOVES WHEN SERVICING.

DO NOT ALLOW PEOPLE OR PETS TO RIDE ON THE

MOWER WHEN RUNNING OR STOPPED.

DISENGAGE THE MOWER BLADES AND USE EXTREME

CAUTION WHEN CROSSING DRIVEWAYS, SIDEWALKS, OR

ROAD WAYS. BE ALERT FOR TRAFFIC AND HIDDEN ROAD

HAZARDS.

NEVER LEAVE TOW VEHICLE OR MOWER RUNNING

UNATTENDED. MAKE SURE TO SHUT DOWN THE TOW

VEHICLE PER MANUFACTURERS INSTRUCTIONS. SET THE

PARKING BRAKE AND REMOVE THE KEY. DISENGAGE THE

MOWER CUTTING BLADES, SHUT DOWN THE ROUGH

CUT MOWER ENGINE AND REMOVE THE KEY.

SHUT OFF ENGINE BEFORE ADJUSTING DECK HEIGHT.

KEEP HANDS AND FEET FROM UNDER THE DECK. MAKE

SURE BLADES ARE STOPPED. THE MOWER IS HEAVY AND

COULD CAUSE INJURY.

DO NOT PLACE HANDS OR FEET UNDER DECK OF MOWER

WHEN ENGINE IS RUNNING OR BLADES ARE TURNING.

FAILURE TO FOLLOW WARNINGS CAN RESULT IN SERIOUS

INJURY OR DEATH.

OPERATION

How to Start the Mower

1. Make sure the battery is connected and grounded. SEE

FIGURE 4

2. Make sure the blade control lever is in the DISENGAGED

position. SEE FIGURE 5

WARNING

Owner’s Manual

ACREAGE™ ROUGH CUT MOWER

Get parts online at www.GetEarthquake.com or Call 800-345-6007 M-F 8-5 CST

Cutter Deck Height Adjustment

1. To adjust the cutting height:

a. Apply foot pressure to the deck height adjuster foot

pad. SEE FIGURE 6

b. While holding foot pressure on the foot pad, lift

the spring loaded deck height adjustment knob to

disengage and allow movement of the deck height

adjuster.

c. Apply or release foot pressure on the deck height

adjuster foot pad to align the index holes on the top

deck height adjuster to achieve the desired height.

d. Release the spring loaded deck height adjustment

knob into the appropriate hole to secure the mower

deck at the required height.

SPRING LOADED

DECK HEIGHT

ADJUSTMENT KNOB

DECK HEIGHT

ADJUSTER

INDEX HOLES

DECK HEIGHT

ADJUSTER

FOOT PAD

FIGURE 6: CUTTER DECK HEIGHT ADJUSTMENT.

BLADE CONTROL LEVER

(FORWARD TO ENGAGE -

BACKWARD TO DISENGAGE)

FIGURE 5: CUTTER BLADE CONTROL LEVER.

Tow Bar Oset Adjustment

1. Oset the tow bar deck mount degree plate and tow bar

hitch degree plates as follows:

a. Lift the spring loaded tow bar locking pin knob

and turn 90 degrees to lock in the up/disengaged

position. SEE FIGURE 7

b. Position the tow bar at the desired numbered oset

hole on the deck mount degree plate. SEE FIGURE 8

AND TABLE 1

c. Lift the spring loaded tow bar locking pin knob

and turn 90 degrees to lock in the down/engaged

position. Make sure the pin engages completely.

NEGATIVE WIRE (BLACK) TO

NEGATIVE TERMINAL

POSITIVE WIRE (RED) TO

POSITIVE TERMINAL

FIGURE 4: BATTERY WIRE ROUTING.

3. Turn the key switch to the center position RUN position

and then to the START position for no more than 5

seconds. Repeat up to 3 times until the engine starts.

(If engine fails to start after 3 attempts, refer to Trouble

Shooting Guide). When the engine starts, release the key

to the RUN position.

How to Stop the Mower

1. Make sure the blade control lever is in the DISENGAGED

position.

2. Turn the key to the STOP position. Always remove the key

for safety.

Engage/Disengage the Cutter Blades

1. Engage the cutter blades by pulling the blade control

lever towards the front of the mower. SEE FIGURE 5

2. Disengage the cutter blades by pushing the blade control

lever towards the rear of the mower.

2. Repeat Steps 1 a. - d. to adjust the other side.

NOTE: Make sure the left and right sides of the mower deck

height adjustment is the same on both sides. Cutting height

is between 3.5 to 7.5 inches.

Owner’s Manual

ACREAGE™ ROUGH CUT MOWER

Get parts online at www.GetEarthquake.com or Call 800-345-6007 M-F 8-5 CST

2. Repeat Steps 1 a. - c. to adjust the hitch degree plate.

NOTE: Make sure both the hitch and deck mount degree

plates are indexed into the same numbered hole.

SPRING LOCK

(UP/DISENGAGED)

SPRING LOCK

(DOWN/ENGAGED)

DECK

MOUNT

DEGREE

PLATE

HITCH

MOUNT

DEGREE

PLATE

TOW BAR

FIGURE 7: TOW BAR OFFSET ADJUSTMENT

DO NOT LEAVE MOWER UNATTENDED WHILE ENGINE

OR TOW VEHICLE IS RUNNING. SET THE TOW VEHICLE

PARKING BRAKE, SHUT OFF THE TOW VEHICLE.

DISENGAGE THE MOWER CUTTING BLADES, SHUT OFF

THE ROUGH CUT MOWER ENGINE. WAIT FOR THE MOWER

BLADES TO STOP ROTATING.

NEVER RUN THE ENGINE INDOORS OR IN A POORLY

VENTILATED AREA. ENGINE EXHAUST CONTAINS

CARBON MONOXIDE, AN ODORLESS AND DEADLY GAS.

KEEP HANDS, FEET, HAIR AND LOOSE CLOTHING AWAY

FROM THE MOWER AND ANY MOVING PARTS ON THE

ENGINE.

DO NOT TOUCH THE MUFFLER OR SURROUNDING AREAS.

TEMPERATURES MAY EXCEED 150 DEGREES FAHRENHEIT.

DEBRIS SUCH AS STICKS, GRAVEL OR ROCKS CAN BE

THROWN WITH SUFFICIENT FORCE TO CAUSE PERSONAL

INJURY OR PROPERTY DAMAGE.

CHECK THE TOW VEHICLE OWNERS MANUAL TO

DETERMINE THE TOWING CAPACITY ON SLOPES AND

HILLS. USE EXTREME CAUTION WHEN OPERATING THE

MOWER HILLY, UNEVEN, OR WET TERRAIN. MAKE SURE

YOU FOLLOW RECOMMENDATIONS SO YOU DO NOT TIP

THE MOWER OVER.

NEVER USE THE MOWER ON SLOPES GREATER THAN 20

DEGREES.

FOR BETTER CONTROL ON SLOPES, MOW UP AND DOWN

AND NEVER ACROSS THE SLOPE.

FIGURE 8: TOW BAR OFFSET POSITION GUIDE

TABLE 1. TOW BAR OFFSET GUIDE

Position Oset (in)

1 27.5 LEFT

2 20.0 LEFT

3 11.5 LEFT

4 10.0 LEFT

5 0.00

6 10.0 RIGHT

7 11.5 RIGHT

8 20.0 RIGHT

9 27.5 RIGHT

WARNING

Owner’s Manual

ACREAGE™ ROUGH CUT MOWER

Get parts online at www.GetEarthquake.com or Call 800-345-6007 M-F 8-5 CST

Mower Tips:

• Never operate outside of tow vehicle

recommendations.

• If the weeds or grass are tall and thick, operate the

mower at a slower towing speed.

• Frequently clean the underside of the mower to

remove any grass build up. See the "Maintenance,

Service and Storage" section for details.

• Do not mow on excessively steep slopes. Never use

the mower on slopes greater than 20 degrees using

any type of tow vehicle. Do not mow on slopes when

the ground is slippery or wet. Mow up and down the

face of the slope, not across.

• Do not operate tow vehicle over 5 mph on at terrain,

or 4 mph on rough terrain while towing the mower.

• When cutting larger wooded sections like small

saplings, allow the mower to ride up over the material

slowly. Use a slower speed to adjust for various

conditions.

• After the rst pass of cutting large saplings, mow the

section again to clean additional debris. Mow from

the trunk towards the top as the brush lays on the

ground.

• When cutting heavy brush in o set mowing, keep the

oset by 10 inches (Position 4 or Position 6).

• Do not use a commercial or non-commercial

automobile, truck, sport utility vehicle (SUV) or

motorcycle, as dened by the Wisconsin Department

of Motor Vehicles, to tow the Rough Cut Mower.

These vehicles make it dicult to see and control the

mower. Use of these tow vehicle types will void the

warranty.

Tow Vehicle Recommendations:

Acreage™ recommends a tow vehicle be either two or four

wheel drive. Some suitable suggestions are listed below:

• Compact or Sub-compact tractor,

• Utility Vehicle (UTV)

• All-Terrain Vehicle (ATV)

• Lawn/Garden Tractor (17 HP and above and weighing

at least 500 lbs.)

• Riding lawn mowers with engines under 17 HP and

weighing less than 500 lbs. are not suitable for use on

slopes greater than 5 degrees.

NOTE: Do not operate the tow vehicle out side of the

manufacturers recommended operating instructions or

conditions. Lawn and garden tractors work best as tow

vehicles when the cutting deck is removed.

MAINTENANCE, SERVICE, AND STORAGE

SERVICE AND ADJUSTMENT

How to Change Engine Oil

See engine manual for manufacturer’s recommendations.

BEFORE YOU INSPECT, CLEAN OR SERVICE THE MOWER,

STOP THE ENGINE. MAKE SURE THAT ALL MOVING PARTS

HAVE STOPPED. DISCONNECT THE WIRE FROM THE

SPARK PLUG AND REMOVE KEY FROM THE IGNITION.

WARNING

Owner’s Manual

ACREAGE™ ROUGH CUT MOWER

Get parts online at www.GetEarthquake.com or Call 800-345-6007 M-F 8-5 CST

SERVICE RECORDS

BEFORE EACH

USE EVERY 25 HOURS AS NOTED

SERVICE

DATE

CHECK ENGINE OIL LEVEL X

CHECK MOWER BLADES X

CHECK TIRE PRESSURE X

ENGINE/MACHINE CLEANING X 1

CHECK NUTS AND BOLTS X

CHECK SPARK PLUG X 2

CHANGE ENGINE OIL X 2

SERVICE AIR FILTER X 2

Maintenance Schedule

NOTE: Maintenance, replacement or repair of the emissions control devices and systems may be performed by any non-road

engine repair establishment or individuals. However, items must be serviced by an authorized dealer to obtain "no charge"

emissions control service. Good maintenance is essential to help reduce air pollution and for safe, economical and trouble-free

operation.

GENERAL RECOMMENDATIONS

The warranty on this mower does not cover items that have

been subjected to operator abuse or negligence. To receive

full value from the warranty, the operator must maintain

the mower as instructed in this manual.

Some adjustments must be made periodically to properly

maintain your mower. All adjustments in the "Service and

Adjustments" section of this manual must be checked at

least once each season.

Note 1 - Clean daily if used in extremely dusty or dirty conditions.

Note 2 - Change more often if used in extremely dusty or dirty conditions. Follow engine manufacturer’s

recommendation.

Owner’s Manual

ACREAGE™ ROUGH CUT MOWER

Get parts online at www.GetEarthquake.com or Call 800-345-6007 M-F 8-5 CST

STORAGE

When the mower is put in storage for thirty days or more,

follow the steps below to make sure the mower is in good

condition the following season.

Mower:

Completely Clean The Mower

Store the mower in a building that is well- ventilated.

1. Completely clean the mower, including dirt and debris

from the cylinder cooling ns and the engine housing.

2. Fully charge battery. After complete charge, disconnect

negative battery terminal and move away from battery

post.

3. When not in use, disconnect spark plug lead, remove

key from ignition and store in a well-ventilated area

inaccessible to children.

NOTE: A yearly check-up or tune-up at an authorized service

dealer will ensure that the mower will provide maximum

performance for the next season.

Engine:

1. Follow manufacturer’s recommendation for engine long-

term storage.

TROUBLESHOOTING & REPAIR

At Earthquake®, we build quality and durability into the design

of our products; but no amount of careful design by us, and

careful maintenance by you, can guarantee a repair-free life for

your Rough Cut Mower. Most repairs will be minor, and easily

xed by following the suggestions in the troubleshooting

guide in this section.

The guide will help you pinpoint the causes of common

problems and identify remedies.

For more complicated repairs, you may want to rely on an

authorized service center. A parts breakdown is located toward

the end of this manual.

We will always be glad to answer any questions you have, or

help you nd suitable assistance. To order parts or inquire

about warranty, call or email us using the contact information

found below.

Ordering Replacement Parts

Parts can be obtained from the store where the rough cut

mower was purchased or direct from the factory. To order

parts visit www.getearthquake.com or call 800-345-6007.

For other general questions, you can e-mail us at info@

getearthquake.com.

Please include the following information with your order:

1) Part numbers

2) Part description

3) Quantity

4) Model number and serial number

DO NOT REMOVE GASOLINE WHILE INSIDE A BUILDING,

NEAR A FIRE, OR WHILE YOU SMOKE. GASOLINE FUMES

CAN CAUSE AN EXPLOSION OR A FIRE.

WARNING

Owner’s Manual

ACREAGE™ ROUGH CUT MOWER

Get parts online at www.GetEarthquake.com or Call 800-345-6007 M-F 8-5 CST

TROUBLESHOOTING GUIDE

NOTE: Please see the engine manual for a full troubleshooting guide for any engine issues.

Trouble Cause Correction

Engine does not start Spark plug wire disconnected Connect spark plug wire

Defective or incorrectly gapped spark plug See engine manual

Fuel tank empty Add fuel

Dirty carburetor or fuel line See engine manual

Dirty air lter See engine manual

Carburetor out of adjustment For carburetor adjustment, take the unit to an

authorized service center

Engine ooded Wait several minutes before starting

Stale gasoline Drain old gasoline and add fresh gas

Defective ignition See engine manual

Battery has no charge Charge and replace if dead, damaged, or defective

Engine runs poorly Bad spark plug Replace spark plug

Dirty air lter See engine manual

Carburetor out of adjustment For carburetor adjustment, take the unit to an

authorized service center

Stale gasoline Drain old gasoline and add fresh gas

Engine cooling system clogged Clean debris screen and engine cooling ns

Engine overheats Engine cooling system clogged Clean debris screen and engine cooling ns

Carburetor out of adjustment For carburetor adjustment, take the unit to an

authorized service center

Oil level is low Add oil

Engine will not stop

running

Ignition failed Inspect and replace damaged parts

Wire disconnected from ignition Inspect, repair, or replace damaged parts

Poor Mower

performance

Cutter Blades Dull Sharpen mower cutter blades,

Mower vibrates Loose nuts or bolts Check all bolts and nuts, including engine bolts

Broken mower head Replace broken part

Owner’s Manual

ACREAGE™ ROUGH CUT MOWER

Get parts online at www.GetEarthquake.com or Call 800-345-6007 M-F 8-5 CST

Use this guide to determine slope angle.

DO NOT MOW ON A SLOPE GREATER THAN 20

DEGREES.

• A 10 degree slope is a hill that increases in height at

approximately 1.76 feet (53.6 cm) in 10 feet (304.5 cm).

• A 20 degree slope is a hill that increases in height at

approximately 3.64 feet (110.9 cm) in 10 feet (304.5 cm).

SLOPE GUIDE

WARNING

USE EXTREME CARE AT ALL TIMES AND AVOID SUDDEN

TURNS OR MANEUVERS. FOLLOW OTHER INSTRUCTIONS

IN THIS MANUAL FOR SAFETY IN MOWING ON SLOPES.

OPERATE A MOWER UP AND DOWN SLOPES, NEVER

ACROSS SLOPES. USE EXTRA CARE WHEN OPERATING ON

OR NEAR SLOPES AND OBSTRUCTIONS.

20 DEGREES FOLD ALONG DOTTED LINE

10 DEGREES

20 DEGREES

SLOPE GUIDE

Sight and hold this guide level with a vertical

tree, a corner of a structure, a power line

pole, or a fence.

Manuel de l’utilisateur

FAUCHEUSE TRACTÉE ACREAGE™

Pièces détachées en ligne à www.GetEarthquake.com ou composer le 800-345-6007 L-V 8h-17h HNC

INTRODUCTION

Merci d’avoir acheté ce produit Earthquake®. Nous nous sommes attachés à ce que ce produit réponde aux plus hautes normes d’utilisation et de

durabilité. Moyennant des soins corrects, votre achat orira de nombreuses années de service able.

Lire ce manuel en entier avant de l’installer et de l’utiliser. Earthquake® se réserve le droit de changer, modier ou améliorer ce produit et cette

documentation à tout moment sans préavis. En raison des constantes améliorations de nos produits, les représentations du produit peuvent être

inexactes. Un certain assemblage peut être requis.

Lire ce manuel et le conserver pour toute consultation ultérieure. Ce manuel contient des renseignements importants concernant la sécurité,

l’assemblage, l’utilisation et l’entretien. Le propriétaire doit veiller à ce que toute la documentation sur le produit soit fournie avec l’appareil.

Cette documentation comprend le manuel, la liste des pièces de rechange et les garanties. Cette documentation doit être fournie en vertu de la

réglementation en vigueur. Toutes les personnes à qui cette machine est louée/prêtée doivent avoir accès à ces informations et les comprendre.

Le présent manuel doit rester avec le produit, notamment s’il est revendu.

SOMMAIRE

Introduction / Sommaire ........................................................................................................................................................................................................................................ 20

Schéma d’identication des vis ............................................................................................................................................................................................................................ 21

Avertissements et mesures de précaution ................................................................................................................................................................................................. 22-27

Caractéristiques ......................................................................................................................................................................................................................................................... 28

Assemblage ...........................................................................................................................................................................................................................................................29-30

Utilisation ...............................................................................................................................................................................................................................................................30-33

Entretien et entreposage ..................................................................................................................................................................................................................................33-35

Dépannage et réparation ....................................................................................................................................................................................................................................... 35

ARRÊTEZ!

ARRÊTEZ! ACTIVEZ LA GARANTIE AVANT UTILISATION

Tous les produits doivent être enregistrés dans les 30 jours à compter de la date d’achat pour être couverts par la garantie.

Pour plus d’information sur la garantie et l’enregistrement, veuillez consulter les modalités et conditions de la garantie et

de l’enregistrement gurant dans l’encart de garantie.

ENREGISTREMENT ET SERVICE APRÈSVENTE

Consigner le numéro de modèle et le numéro de série du produit

dans l’espace prévu pour y accéder facilement lors des commandes

de pièces détachées ou des demandes d’assistance technique. À

l’exception des articles couverts par la garantie sur le contrôle des

émissions, la garantie est valable uniquement si l’enregistrement

dûment rempli est reçu par Ardisam dans les 30 jours après l’achat.