Bloomfield EBC™ 3 Warmer Brewer Le manuel du propriétaire

Marque: Bloomfield

Modèle: EBC™ 3 Warmer Brewer

Catégorie: Cafetières

Taper: Le manuel du propriétaire

Ce manuel convient également à

641

Includes:

Installation

Use & Care

Servicing Instructions

2060 Cessna Dr, Suite 100

Vacaville, CA 95688

telephone: 707-448-5151

fax: 707-448-1521

www.bloomfieldworldwide.com

OWNERS MANUAL

for

E. B. C.™

Electronic Brew Control ™

DECANTER

COFFEE BREWERS

p/n 2M-75844 Rev J 146M 190613

E.B.C.™ brewers are protected under

U. S. Patent # 5,704,275

Other U. S. and Canadian patents pending.

Models 1012 Brewer

with optional

8900-Series Glass Decanters

Model 1072 Brewer

with optional

8900-Series Glass Decanters

MODELS

1012

1040

1072

NOTE: For your protection, please note that equipment in

this shipment was carefully inspected and packaged by skilled

personnel before leaving the factory.

Upon acceptance of this shipment, the transportation

company assumes full responsibility for its safe delivery.

IF SHIPMENT ARRIVES DAMAGED:

1. VISIBLE LOSS OR DAMAGE: Be certain that any

visible loss or damage is noted on the freight bill

or express receipt, and that the note of loss or damage

is signed by the delivery person.

2. FILE CLAIM FOR DAMAGE IMMEDIATELY:

Regardless of the extent of the damage.

3. CONCEALED LOSS OR DAMAGE: if damage is

unnoticed until the merchandise is unpacked, notify the

transportation company or carrier immediately, and

¿OH³&21&($/(''$0$*(´FODLPZLWKWKHP This

PXVWEHGRQHZLWKLQ¿IWHHQGD\VIURPWKHGDWH

the delivery was made to you. Be sure to retain the

container for inspection.

%ORRP¿HOGFDQQRWDVVXPHOLDELOLW\IRUGDPDJHRUORVV

incurred in transit. We will, however, at your request, supply

you with the necessary documents to support your claim.

WARRANTY STATEMENT

SERVICE POLICY AND PROCEDURE GUIDE

ADDITIONAL WARRANTY EXCLUSIONS

yp ,p qp

TE: For

our

rotection

lease note that e

ment in

EALED L

OSS

R DAMA

E: i

dama

e is

SHIPPING DAMAGE CLAIMS PROCEDURE

1. Resetting of safety thermostats, circuit breakers,

overload protectors, or fuse replacements.

2. All problems due to operation at voltages other than

VSHFL¿HGRQHTXLSPHQWQDPHSODWHVFRQYHUVLRQWR

correct voltage must be the customer’s responsibility.

3. All problems due to electrical connections not made in

accordance with electrical code requirements and

wiring diagrams supplied with the equipment.

4. Replacement of items subject to normal wear, to

include such items as knobs and light bulbs. Normal

maintenance functions including adjustment of

thermostats, microswitches, and replacement of fuses

and indicating lights are not covered under warranty.

 All problems due to inadequate water supply, such as

ÀXFWXDWLQJRUKLJKRUORZZDWHUSUHVVXUH

6. All problems due to mineral/calcium deposits, or

FRQWDPLQDWLRQIURPFKORULGHVFKORULQHV'HOLPLQJLV

considered a preventative maintenance function and is

not covered by warranty.

All electrical equipment manufactured by BLOOMFIELD is

warranted against defects in materials and workmanship

for a period of (1 year labor, two year parts) from the date

RIRULJLQDOLQVWDOODWLRQDQGLVIRUWKHEHQH¿WRIWKHRULJLQDO

purchaser, except that:

a. airpots carry a 30 day parts warranty only.

b. dispensers; i.e., tea and coffee carry a 90 days parts

warranty only, excludes decanters.

c. decanters are not covered by this warranty

THE FOREGOING OBLIGATION IS EXPRESSLY GIVEN

IN LIEU OF ANY OTHER WARRANTIES, EXPRESSED

OR IMPLIED, INCLUDING ANY IMPLIED WARRANTY OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR

PURPOSE, WHICH ARE HEREBY EXCLUDED.

BLOOMFIELD, LLC SHALL NOT BE LIABLE FOR

INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES

OR LOSSES FROM ANY CAUSE WHATSOEVER.

This warranty is void if it is determined that upon inspection

by an authorized service agency that the equipment has

EHHQPRGL¿HGPLVXVHGPLVDSSOLHGLPSURSHUO\LQVWDOOHGRU

GDPDJHGLQWUDQVLWRUE\¿UHÀRRGRUDFWRI*RG

It also does not apply if the serial nameplate has been

removed or unauthorized service personnel perform service.

7KHSULFHVFKDUJHGE\%ORRP¿HOGIRULWVSURGXFWVDUHEDVHG

upon the limitations in this warranty. Seller’s obligation under

this warranty is limited to the repair of defects without charge

E\D%ORRP¿HOG Authorized Service Agency or one of its

VXEDJHQFLHV This service will be provided on customer’s

SUHPLVHVIRUQRQSRUWDEOHPRGHOV3RUWDEOHPRGHOVDGHYLFH

ZLWKDFRUGDQGSOXJRWDGLVSHQVHUPXVWEHWDNHQRUVKLSSHG

to the closest authorized service agency, transportation

charges prepaid, for services.

In addition to restrictions contained in this warrantyVSHFL¿F

OLPLWDWLRQVDUHVKRZQEHORZ$GGLWLRQDOWDUUDQW\([FOXVLRQV

%ORRP¿HOG Authorized Service Agencies are located in

principal cities.

This warranty is valid in the United States, Canada and void

HOVHZKHUH3OHDVHFRQVXOW\RXUFODVVL¿HGWHOHSKRQHGLUHFWRU\

or your food service equipment dealer; or, for information and

other details concerning warranty, write to:

7. Full use, care and manuals may or may not be sent with

each unit, only a condensed version. Please visit our

web site to download the full version.

8. TUDYHOPLOHDJHLVOLPLWHGWR¿IW\PLOHVIURPDQ

DXWKRUL]HGVHUYLFHDJHQF\RURQHRILWVVXEVHUYLFH

agencies.

9. All labor shall be performed during normal working hours.

Overtime premium shall be charged to the customer.

10. $OOJHQXLQH%ORRP¿HOGUHSODFHPHQWSDUWVDUHZDUUDQWHG

IRUQLQHW\GD\VIURPGDWHRISXUFKDVHRQQRQ

warranted equipment. Any use of non-genuine

%ORRP¿HOGSDUWVFRPSOHWHO\YRLGVDQ\ZDUUDQWy.

11. Installation, labor and job checkouts are not considered

warranty.

12. Charges incurred by delays, waiting time or operating

restrictions that hinder the service technicians ability

to perform services are not covered by warranty.

This includes institutional and correctional facilities.

641 p/n 2M-75844 1012 1040 1072 Owmers Manual

PARTS TOWN

1200 Greenbriar Dr,

Addison, IL 60101

Phone: (800) 438-8898 Fax: (888) 513-0259

[email protected] / www.bloomfieldworldwide.com

TABLE OF CONTENTS

SPECIFICATIONS

Thank You for purchasing this

WARRANTY STATEMENT xi

SPECIFICATIONS 1

FEATURES & OPERATING CONTROLS 2

PRECAUTIONS & GENERAL INFORMATION 3

AGENCY LISTING INFORMATION 3

INSTALLATION INSTRUCTIONS 4

OPERATION 6

BREWING COFFEE 10

CLEANING INSTRUCTIONS 11

TROUBLESHOOTING SUGGESTIONS 12

SERVICING INSTRUCTIONS 14

EXPLODED VIEWS & PARTS LISTS 22

WIRING DIAGRAMS 29

APPLICABILITY

1012

1040

1072

641 p/n 2M-75844 1012 1040 1072 Owmers Manual

Country Model Style Volts Amps Was Power Supply Cord

4A-1012D3F-120V 3W In-Line 15 1800

4A-1040D2F-120V 2W In-Line 14.2 1700

4A-1072D3F-120V 3W Lo Proﬁle 15 1800

4A-1012D3F-120C 3W In-Line 15 1800

4A-1040D2F-120C 2W In-Line 14.2 1700

4A-1072D3F-120C 3W Lo Proﬁle 15 1800

USA

CAN

120

NEMA 5-15P

NEMA 5-20P

FEATURES AND OPERATING CONTROLS

Fig. 1 Features & Operating Controls

641 p/n 2M-75844 1012 1040 1072 Owmers Manual

PRECAUTIONS AND GENERAL INFORMATION

WARNING: ELECTRIC SHOCK HAZARD

service personnel. Do not open any access panels which require the use of tools. Failure

to heed this warning can result in electrical shock.

WARNING: INJURY HAZARD

all applicable electrical and plumbing codes. Failure could result in property damage and

personal injury.

WARNING: ELECTRIC SHOCK HAZARD

Brewer must be properly grounded to prevent possible shock hazard. DO NOT assume a

plumbing line will provide such a ground. Electrical shock will cause death or serious Injury.

WARNING: BURN HAZARD

This appliance dispenses very hot liquid. Serious bodily injury from scalding can occur from

contact with dispensed liquids.

This appliance is intended for commercial use only.

This appliance is intended for use to brew beverage products for

human consumption. No other use is recommended or

authorized by the manufacturer or its agents.

This appliance is intended for use in commercial establishments,

where all operators are familiar with the appliance use,

limitations and associated hazards. Operating instructions and

warnings must be read and understood by all operators and

users.

Except as noted, this piece of equipment is made in the USA

and has American sizes on hardware. All metric conversions are

approximate and can vary in size.

The following trouble shooting, component views and parts lists

are included for general reference, and are intended for use by

This manual should be considered a permanent part of this

appliance. The manual must remain with the appliance if it is

sold or moved to another location.

CAUTION:

EQUIPMENT DAMAGE

DO NOT plug in or energize this

appliance until all Installation

Instructions are read and followed.

Damage to the Brewer will occur if

these instructions are not followed.

CAUTION:

BURN HAZARD

Exposed surfaces of the

appliance, brew chamber and

decanter may be HOT to the

touch, and can cause serious

burns.

AGENCY APPROVAL INFORMATION

E d

DO NO

WARNING

641 p/n 2M-75844 1012 1040 1072 Owners Manual

These brewers are listed under ETL 3016449.

This brewer meets

Standard 4 only when installed,

operated and maintained in accordance with the enclosed

instructions.

STD 4

INSTALLATION INSTRUCTIONS

READ THIS CAREFULLY BEFORE STARTING THE INSTALLATION

Unpack the unit. Inspect all components for completeness and

condition. Ensure that all packing materials have been removed

from the unit.

Verify that the Spray Head Gasket (#33) and Spray Disk (#34)

are properly installed.

LEVELING THE UNIT

Verify that an adjustable leg is installed at each corner of the

brewer.

Set Brewer in its operating location. Level the Brewer. A spirit

level should be placed on the top of the unit, at the edge, as a

guide when making level adjustments.

Level the unit from left to right and front to back by turning the

adjustable feet. Be sure all four feet touch the counter to prevent

tipping.

PLUMBER’S INSTALLATION INSTRUCTIONS

Brewer should be connected to a POTABLE WATER, COLD

WATER line. Flush water line before connecting to Brewer.

DO NOT use a saddle valve with a self-piercing tap for the water

line connection. Such a tap can become restricted by waterline

debris. For systems that must use a saddle tap, shut off the

main water supply and drill a 3/16” (minimum) tap for the saddle

connection, in order to insure an ample water supply. Remember

WRÀXVKWKHOLQHSULRUWRLQVWDOOLQJWKHVDGGOH

The brewer must be installed on a water line with average

pressure between 20 PSI and 90 PSI. If your water pressure

exceeds 90 PSI at anytime, a pressure regulator must be

installed in the water supply line to limit the pressure to not more

than 90 PSI in order to avoid damage to lines and solenoid.

A water shut-off valve should be installed on the incoming water

line in a convenient location (Use a low restriction type valve,

VXFKDVDWXUQEDOOYDOYHWRDYRLGORVVRIZDWHUÀRZWKUXWKH

valve.

The provided water line strainer must be installed in the supply

line, between the shutofIYDOYHDQGLQOHW¿WWLQJ1RWH)/2:

arrow marking on strainer body.

IMPORTANT:

To enable the installer to make

a quality installation and to

minimize installation time, the

following suggestions and tests

should be done before the

actual unit installation is started:

CAUTION:

EQUIPMENT

DAMAGE

DO NOT plug in or energize this

appliance until all Installation

Instructions are read and

followed. Damage to the

Brewer will occur if these

instructions are not followed.

CAUTION:

UNSTABLE

EQUIPMENT

HAZARD

It is very important for safety

and for proper operation that the

brewer is level and stable when

VWDQGLQJLQLWV¿QDORSHUDWLQJ

position. Provided adjustable,

non-skid legs must be installed

at each corner of the unit.

Failure to do so will result in

movement of the brewer which

can cause personal Injury and/

or damage to brewer.

NOTE: :ater supply inlet line

must meet certain minimum

criteria to insure successful

operation of the brewer.

%ORRP¿HOGUHFRPPHQGV´

copper tubing for installation of

less than 12 feet and 3/8” for

more than 12 feet from a 1/2”

water supply line.

641 p/n 2M-75844 1012 1040 1072 Owmers Manual

INSTALLATION INSTRUCTIONS (continued)

NOTE: This equipment must

be installed to comply with

all applicable federal, state

and local plumbing codes and

ordinances.

WARNING:

SHOCK HAZARD

Brewer must be properly

grounded to prevent possible

shock hazard. DO NOT

assume a plumbing line

will provide such a ground.

Electrical shock will cause death

or serious injury.

IMPORTANT: Do not connect

brewer to electrical power until

WKHWDQNLV¿OOHGZLWKZDWHr.

Pour water into the pour-over

RSHQLQJXQWLOZDWHUÀRZVIURP

the brew head.

IMPORTANT:

Supply power must match

nameplate for voltage and

phase. Connecting to the

wrong voltage will damage the

brewer or result in decreased

performance. Such damage is

not covered by warranty.

NSF requires that the brewer be able to be moved for cleaning

underneath. AÀH[OLQHRUORRSVRIFRSSHUWXELQJZLOOVDWLVI\WKLV

requirement. See Figure 2 below.

,QVRPHDUHDVORFDOFRGHVUHTXLUHDEDFNÀRZSUHYHQWHU (check

YDOYHWREHLQVWDOOHGRQWKHLQOHWZDWHUOLQH,IDEDFNÀRZ

preventer is used, you must install a water hammer arrester

LQWKHLQFRPLQJOLQHEHWZHHQWKHEDFNÀRZSUHYHQWHUDQGWKH

brewer inlet, as far away from the brewer as space will allow.

7KLVZLOOUHOLHYHWKHH[FHVVLYHEDFNSUHVVXUHVWKDWFDQFDXVH

faucet leaks and solenoid malfunctions.

ELECTRICIAN’S INSTALLATION INSTRUCTIONS

REFER TO ELECTRICAL SPECIFICATIONS - Page 1

Check the nameplate to determine correct electrical service

required for the Brewer to be installed.

IMPORTANT: Before connecting to electricity, make sure

automatic brewers are connected to the water supply.

Models 1012, 1040 & 1072 (US only) are equipped with a cord

and plug. They require a 115 - 125 volt 15 amp circuit (50/60 Hz,

2 wire plus ground, with NEMA 5-15R or 5-20R Receptacle).

IMPORTANT: The ground prong of the plug is part of a system

designed to protect you from electrical shock in the event of

internal damage. Never cut off the ground prong nor twist a

EODGHWR¿WDQH[LVWLQJUHFHSWDFOH&RQWDFWDOLFHQVHGHOHFWULFLDQ

to install the proper circuit and receptacle.

IL1615

Fig. 2 Water Supply Installation

641 p/n 2M-75844 1012 1040 1072 Owmers Manual

Brewer mu

NEMA 5-15P

PLUG

GROUND

NEMA 5-15R

RECEPTACLE

IL1686

OPERATION

Fig. 4 Brewer Operation Diagram

START-UP

For initial start-up, or if the brewer has not been used for an

extended period of time:

• Be sure spray disk and brew gasket are properly installed in the

brew head.

• Be sure the water supply is properly connected and the water

supply valve is turned ON.

• Be sure the WATER TANK IS FILLED

BEFORE plugging the brewer into a receptacle, or otherwise

connecting brewer to electrical power THE WATER TANK MUST

BE FILLED. Place an empty decanter under the brew head. Lift

the pour-over cover then pour warm tap water into the pour-over

RSHQLQJXQWLOZDWHUÀRZVIURPWKHEUHZKHDG:KHQZDWHUVWRSV

dripping from the brew head, empty the container.

Once the tank is full of water, connect the brewer to electrical

power. For Models 1016 & 1074, press power switch to ON.

The heating elements will begin heating the water in the tank.

When the water has reached the proper temperature, the

“HEAT” LED will go out.

A.IMPORTANT:

Tank must be full of

water before connecting

brewer to electrical power.

Heating elements will be

damaged if allowed to

operate without being fully

submerged in water.

Damage caused by

operating the brewer

without water in the tank

is NOT COVERED BY

WARRANTY.

IL2203

641 p/n 2M-75844 1012 1040 1072 Owmers Manual

OPERATION (continued)

WATER HEATER

Water temperature is sensed by an electronic water

temperature probe inserted into the water tank.

This temperature signal is fed to the controller.

The setpoint temperature is adjustable. The

controller sends a command signal to the power

board based upon a comparison between the

setpoint temperature and actual temperature.

See page 17.

The power board energizes the heating elements

based on the command signal from the controller.

Excessive temperature will trip the hi-limit safety

switch. The hi-limit will automatically reset when

the brewer cools.

WATER FLOW

POUR-OVER FEATURE

Pouring any amount of water into the pour-over

opening and into the basin pan forces an identical

amount of heated water out of the tank and through

the spray head.

AUTOMATIC OPERATION

Pressing the BREW key energizes the solenoid

valve, allowing water from an external water supply

WRÀRZLQWRWKHZDWHUWDQN The incoming water

forces heated water out of the tank to perform the

brew.

7KHVROHQRLGXVHVDÀRZFRQWUROGHYLFHVRWKDW

ÀRZLVFRQVLVWHQWEHWZHHQSVLDQGSVL

The length of time the solenoid is open is controlled

by the time setting of the controller. See page 18.

$IWHUWKHVROHQRLGFORVHVZDWHUZLOOFRQWLQXHWRÀRZ

to the brew chamber until the water level in the tank

falls below the brew pickup, breaking the siphon.

HOT WATER FAUCET

The faucet water coil is submerged in the hot water

tank and draws heat from the brew water. Wa-

ter going to the water coil is not controlled by the

solenoid valve.

Hot water is provided at the faucet, at supply water

pressure, any time the faucet shut-off valve is

OPEN

Fig. 6 Water Flow Diagram

Fig. 5 Heat Control Diagram

,/

,/

641 p/n 2M-75844 1012 1040 1072 Owmers Manual

OPERATION (continued)

ELECTRONIC FEATURES

Energizing the Brewer

:KHQHOHFWULFSRZHULVDSSOLHGWRWKHXQLWDOOWKHOLJKWVZLOOÀDVKIRXU

WLPHVDQGIRXUEHHSVZLOOVRXQG 7KHXQLWZLOOEHOFF

Press the ON/OFF key)RXUEHHSVZLOOVRXQGDQGDOOOLJKWVZLOOÀDVK

RQFH The POWER indicator will remain

ON,IWKHZDWHUWHPSHUDWXUH

LVPRUHWKDQ)EHORZWKHVHWSRLQWWKH+(AT indicator will glow until

ZDWHUWHPSHUDWXUHUHDFKHVVHWSRLQW

3UHVVWKH212))NH\DJDLQWRWXUQWKHEUHZHUOFF 7KUHHEHHSVZLOO

VRXQGWKHWDQNKHDWHUDQGDOOZDUPHUVZLOOEHVZLWFKHGRIIDQGDOO

LQGLFDWRUOLJKWVZLOOJRRXW

Brew Settings

6HHSDJHVIRUVHWWLQJ%UHZ Time and THPSHUDWXUH

ABS™ (Automatic Brew Start)

6WDUWDEUHZE\SUHVVLQJ%5(W AVLQJOHEHHSZLOOVRXQG The system

ZLOOYHULI\WKDWWKHZDWHULQWKHWDQNLVDWWKHSURSHUWHPSHUDWXUH,ILWLV

EUHZZLOOVWDUWLPPHGLDWHOy2WKHUZLVHWKH%5(:LQGLFDWRUZLOOÀDVK

%UHZWaiting Mode) until the water reaches setpoint temperature,

WKHQWKHLQGLFDWRUZLOOJORZDQGEUHZZLOOFRPPHQFH,IWKHPDLQ

warmer is oIILWZLOOEHHQHUJL]HGDXWRPDWLFDOOy

$WWKHFRQFOXVLRQRIWKHEUHZF\FOHWKUHHEHHSVZLOOVRXQG

NOTE: TRRYHUULGH%UHZWDLWLQJ0RGHSUHVVDQGKROGWKH%5(:NH\

IRUVHFRQGVZKLOHWKH%5(:LQGLFDWRULVÀDVKLQJ%UHZZLOOEHJLQ

UHJDUGOHVVRIZDWHUWHPSHUDWXUH TRDYRLGXQGHUWHPSHUDWXUHEUHZV

WKLVIHDWXUHVKRXOGRQO\EHXVHGZKHQVHWWLQJEUHZYROXPHV

NOTE: %UHZWDLWLQJ0RGH%5(:LQGLFDWRUÀDVKLQJSUHYHQWV

PXOWLSOHXQDWWHQGHGEUHZV:KLOHWKH%5(:LQGLFDWRULVRQRU

ÀDVKLQJDQ\DGGLWLRQDOVWURNHVRIWKH%5(:NH\ZLOOEHLJQRUHGWKHUH

ZLOOEHDEHHSHDFKWLPHWKHNH\LVSUHVVHGKRZHYHU $QRWKHUEUHZ

FDQQRWEHLQLWLDWHGXQWLOWKHSUHYLRXVEUHZLVFRPSOHWH

7KH%UHZWaiting Time, also called Dripout TLPHLQWHUYDOEHWZHHQ

ZKHQWKHEUHZLVLQLWLDWHGDQGWKHDXGLEOHVLJQDOVRXQGVDWWKHHQG

RIWKHEUHZPD\EHDGMXVWHGEHWZHHQDQGPLQXWHVDWWKH%UHZ

Signal Timer dial on the controller6HHSDJH

Brew Cancel

TRFDQFHODEUHZLQSURJUHVVRUDEUHZLQZDLWLQJSUHVVWKH&$1&(L

key TZREHHSVZLOOVRXQGDQGWKH%5(:LQGLFDWRUZLOOJRRXW

NOTE: ,IDEUHZLQSURJUHVVLVFDQFHOOHGFRIIHHZLOOFRQWLQXHWRÀRZ

XQWLODOOZDWHUGHOLYHUHGKDVGULSSHGWKURXJKWKHEUHZFKDPEHr

IMPORTANT:

DO NOTHQHUJL]HWKLV

EUHZHUXQWLOWKHZDWHU

WDQNKDVEHHQ¿OOHG'U\

¿ULQJZLOOGDPDJHKHDWLQJ

HOHPHQWV6HHSDJH

641 p/n 2M-75844 1012 1040 1072 Owmers Manual

Fig. 7 Turning Brewer

ON or OFF

Fig. 8 Initiate a Brew

Fig 9 Brew Cancel

,/

OPERATION (continued)

Quality Timer is normally

set for 30 minutes. It can

be set for 20 minutes by

moving a jumper on the

controller. See page 17.

After Hours™ is an energy

saving feature. The brew-

er will enter After Hours™

mode if it is not used for

three hours.

Press the BREW key

to immediately return

the brewer to normal

operation.

IMPORTANT:

If the original cause of

the problem has not been

addressed, the brewer will

once again go into Over

Temperature mode four

minutes after being reset.

Quality Timer

Coffee looses its freshness as it sits on a warmer. The Quality Timer

ÀDVKHVWKHZDUPHUOLJKWVPLQXWHVDIWHUWKHODVWEUHZWRUHPLQG\RX

that the coffee is nearing the end of its useful life.

After Hours™ Operation

During normal operation, the controller will maintain the precise

brewing temperature. If, however, if the BREW key in not pressed for

3 hours, the brewer goes into After Hours™ mode; any warmer left on

will be turned off; and, the temperature will only be maintained to within

20ºF. This feature prolongs component life and saves energy.

As soon as the BREW key is pressed, the brewer returns to normal

operation, heating the water to the precise temperature before

beginning the brew. The brewer will return to After Hours™ mode only

if three hours pass without a brew being initiated.

Disable/Enable After Hours™ Feature

To disable After Hours™, press the ON/OFF key to turn the brewer

OFF.

Press and hold the CANCEL key until two beeps sound, and the HEAT

LQGLFDWRUÀDVKHVWZLFH This feature is now disabled.

To re-enable After Hours™, press the ON/OFF key to turn the brewer

OFF. Press and hold the CANCEL key until three beeps sound, and the

32:(5LQGLFDWRUÀDVKHVWZLFH This feature is now enabled, however,

it will not be activated unless no brew is initiated for three hours.

Over-Temperature and Temperature Fault Protection

Should the water temperature exceed 214ºF (101ºC), or if the control-

ler does not detect a 2ºF (1ºC) rise in temperature within four minutes

of calling for heat, the brewer will go into Over Temperature Mode; the

heating element is turned off, all warmers are disabled and all lights will

ÀDVK

Possible causes of Over Temperature condition:

Setpoint is in the boiling range.

Heating element or temperature probe has malfunctioned.

Excessive scale buildup is preventing the element from heating the

water.

Heating element relay fails in the “on” state.

No water in the tank.

Hi-limit safety tripped (must be manually reset)

To reset the brewer:

Determine the cause of the failure and take appropriate remedial

action to rectify the problem.

Press and hold the CANCEL key for three seconds. Four beeps will

sound and the brewer will resume normal operation.



641 p/n 2M-75844 1012 1040 1072 Owmers Manual

BREWING COFFEE

CAUTION:

BURN HAZARD

Exposed surfaces of the

brewer, brew chamber and

decanter may be HOT to

the touch, and can cause

serious burns.

CAUTION:

BURN HAZARD

To avoid splashing or

RYHUÀRZLQJKRWOLTXLGV

ALWAYS place an empty

decanter under the brew

chamber before starting

the brew cycle. Failure to

comply can cause serious

burns.

CAUTION:

BURN HAZARD

After a brew cycle, brew

chamber contents are

HOT. Remove the brew

chamber and dispose of

used grounds with care.

Failure to comply can

cause serious burns.

NOTE: The brewer will not

initiate a second automatic

brew cycle until the current

cycle plus the drip-out time

is completed. If the BREW

key is pressed during this

time, the BREW light will

ÀDVKLQGLFDWLQJDEUHZLQ

progress.

NOTE: Water for the hot

water faucet is heated in

a coil inside of the water

tank. Use of the faucet will

not affect the volume of

water delivered for a brew.

However, overuse of the

faucet during a brew may

lower the temperature of

the brew water.

Exposed

PREPARATION

Place one (1) genuine

%ORRP¿HOGSDSHU¿OWHULQWKH

brew chamber.

Add a pre-measured amount

of fresh coffee grounds.

Gently shake the brew

chamber to level the bed of

grounds.

Slide the brew chamber into

place under the brew head.

B. AUTOMATIC OPERATION

BE sure HEAT light is not lit.

Place the appropriate EMPTY

decanter in place under the

brew chamber.

Press the BREW switch.

The BREW light will glow and

a beep will sound.

The solenoid will open for an

amount of time determined by

the timer setting, admitting a

PHDVXUHGTXDQWLW\RIZDWHU

into the tank.

Inlet water will displace a like amount of heated water from the tank.

The hot water will be forced into the brew head where it will spray

over the bed of grounds. Freshly brewed cofIHHZLOOEHJLQWR¿OOWKH

container under the brew chamber.

At the end of the brew cycle, plus an amount of time set to allow all

water to drip out of the brew chamber, three beeps will sound.

:KHQWKHÀRZDQGDOOGULSSLQJVWRSVWKHFRIfee is ready to serve.

Discard the contents of the brew chamber and rinse it in a sink.

When the HEAT light goes out, the brewer is ready for another

brew cycle.

C. WARMERS

At the start of a brew, the MAIN warmer is energized automatically.

Press either the FRONT or REAR warmer switch to energize an

auxiliary warmer6HWWKH¿OOHGGHFDQWHURQWKHVHOHFWHGZDUPHUWR

keep it warm.

IL1605

PAPER

FILTER

BREW

CHAMBE

Fig. 10 Prepare Brew Chamber

Fig. 11 Press BREW to Start

641 p/n 2M-75844 1012 1040 1072 Owmers Manual

CLEANING INSTRUCTIONS

PROCEDURE: Clean Coffee Brewer

PRECAUTIONS: Disconnect brewer from electric power.

Allow brewer to cool.

FREQUENCY: Daily

TOOLS: Mild Detergent, Clean Soft Cloth or Sponge

Bristle Brush.

1. Disconnect brewer from electric power.

Allow brewer to cool before cleaning.

2. Remove and empty decanters.

3. Remove and empty brew chamber.

4. 5HPRYHWKHVSUD\GLVNIURPWKHEUHZKHDG6HH¿JXUH

Press up on the spray disk ears, and then turn the disk to

the left to unlatch. Remove the gasket from inside the brew

head.

5. Wipe inside of brew head and area around the brew head

with a soft clean cloth or sponge moistened with clean water.

6. Wash the spray disk in a sink using warm water and a mild

detergent. A bristle brush may be used to clear clogged

spray holes. Rinse the spray disk with clean water and allow

to air dry.

7. Wash the brew chamber in a sink using warm water and a

mild detergent. A bristle brush may be used to clean the

inside. Rinse with clean water and allow to air dry. For

stainless steel brew chambers, be sure the wire rack is prop-

erly reinstalled.

 Wipe the exterior of the brewer with a soft clean cloth or

sponge moistened with clean water.

9. Reinstall the gasket INSIDE the brew head, then reinstall the

spray disk.

10. Reinstall the brew chamber.

11. Decanters may be washed in a dishwasher or sink.

Procedure is complete

CAUTION:

BURN HAZARD

Brewing and serving

temperatures of coffee are

extremely hot.

Hot coffee will cause

serious skin burns.

CAUTION:

SHOCK HAZARD

Do not submerge or immerse

brewer in water.

IMPORTANT:

DO NOT use steel wool, sharp

objects, or caustic, abrasive or

chlorinated cleansers to clean

the brewer.

Brewing an

Fig. 12 Cleaning

IL1677

641 p/n 2M-75844 1012 1040 1072 Owmers Manual

TROUBLESHOOTING SUGGESTIONS

SYMPTOM POSSIBLE CAUSE SUGGESTED REMEDY

Water won’t heat

(NOTE: Models 1016 & 1074 must

have power switch ON)

Brewer unplugged or circuit breaker

tripped

Check power supply cord,

Check / reset circuit breaker

Temperature adjusted too low or set

to off

Turn on and set for desired

temperature. See page 15

Hi-Limit thermostat tripped Allow to cool

Damaged internal component or

wiring

Examine wiring & connectors,

controller, power board and

heating element, Repair/replace

as needed

Coffee level too high or low Timer out of adjustment Adjust controller. See page 17

%UHZFKDPEHURYHUÀRZV

TRRPDQ\¿OWHUSDSHUVRUZURQJ¿OWHU

paper

8VHRQHJHQXLQH%ORRP¿HOG

¿OWHUSHUEUHZ

Brew chamber dispense hole

plugged

Thoroughly clean brew chamber

Sprays water from brew head Spray gasket improperly installed

Check/reinstall gasket on INSIDE

of brew head

1REUHZZKLOHIDXFHWÀRZV2.

Spray disk plugged Clean spray disk

Damaged internal component or

wiring

Check keypad, controller,

power board & solenoid,

Repair, replace as needed

1REUHZSOXVQRÀRZIURPKRWZDWHU

faucet

Water supply OFF Turn water supply ON

Solenoid screen plugged Clean solenoid screen

Water line strainer (if used) plugged Clean strainer

1RÀRZIURPKRWZDWHUIDXFHW

WDWHU¿OWHULIXVHGSOXJJHd 5HSODFH¿OWHUHOHPHQW

Faucet valve turned OFF Turn faucet valve ON

Faucet plugged Disassemble faucet, clean

Poor coffee quality

.HHSEUHZHUDQGGHFDQWHUVFOHDQ,QVWDOODWDVWHDQGRGRU¿OWHULQZDWHU

supply, and replace cartridges regularly. Use a quality coffee with a

consistent roast. Use proper grind and amount of coffee per brew.

641 p/n 2M-75844 1012 1040 1072 Owmers Manual

CAUTION:

SHOCK HAZARD

Live electrical circuits may

be exposed while performing

these procedures.

These procedures are to

EHSHUIRUPHGE\TXDOL¿HG

technical personnel only.

ERROR DETECTION

WHAT TO CHECK DESCRIPTION CORRECTIVE ACTION

Has the water

tank been properly

¿OOHG"

On initial startup, an attempt to heat a

dry tank will be detected as too high a

WHPSHUDWXUHRULQVXI¿FLHQWWHPSULVHRU

will trip the high limit.

TDQNPXVWEHSURSHUO\¿OOHGDV

detailed on page 6.

Check hi-limit (see below)

Has hi-limit safety

thermostat tripped

ofI"

Brewer may have been started without

water in the tank, or the temp control

thermostat may require adjustment.

Access hi-limit by removing front

panel. Hi-limit is on the left side of

the tank. Use an insulated tool to

push the red button in until it “clicks”

and stays. Reset per above.

Check control

board and temp

probe.

Brewer will go into error mode

immediately if either the control board

or temp probe is defective.

Temp probe electrical resistance is

approximately 30K at room temp, and

2K at boiling. Replace temp probe if

less than 1K

Reset by holding the CANCEL key for

VHFRQGV,IOLJKWVFRQWLQXHWRÀDVK

Disconnect temp probe from control

board.

D,IOLJKWVFRQWLQXHWRÀDVKXQSOXJ

brewer and replace control board.

E,IOLJKWVVWRSÀDVKLQJXQSOXJ

brewer and replace temp probe.

Check power

board and heating

element..

Brewer will go into error mode 4

minutes after energizing the heating

HOHPHQWLILQVXI¿FLHQWKHDWULVHLV

detected. The heating element is

energized by an electronic power

board, and protected by the hi-limit

safety.

Heating element should receive full line

voltage (i.e. 120V, 208V or 240V).

Be sure the hi-limit safety is reset.

Reset by holding the CANCEL key for

VHFRQGV,IOLJKWVUHVXPHÀDVKLQJ

DIWHUPLQXWHV

Check the voltage across the heating

HOHPHQWWHUPLQDOV

a. If no voltage is present, unplug

brewer and replace power board.

b. If proper voltage is present,

unplug brewer and replace tank

heating element.

Is the brew

temperature

SURSHUO\DGMXVWHG"

The brewer may occasionally go into

error mode if the brew temperature is

set too high.

See page 17 for temperature

adjustment procedure.

This brewer is designed to perform a continuous internal

GLDJQRVLVDQGWRVLJQDOIDXOWVE\ÀDVKLQJDOOWKHOLJKWV,QIDXOW

PRGHZDUPHUVKHDWLQJHOHPHQWDQGZDWHU¿OOVROHQRLGDUHWXUQHG

“off”, and most keypad functions are disabled.

(UURUGHWHFWLRQDOOOLJKWVÀDVKLQJZLOORFFXUXQGHUWZRFRQGLWLRQV

Anytime a temperature in excess of 214ºF is detected.

Temperature does not change by at least 2ºF within 4 minutes

of tank heater being energized (HEAT light on).

To reset the brewer after the fault has been corrected, press and

hold the CANCEL key for 3 seconds, or disconnect the brewer from

electrical power for three seconds.



Li l t i

641 p/n 2M-75844 1012 1040 1072 Owmers Manual

SERVICING INSTRUCTIONS

CAUTION:

SHOCK HAZARD

Opening access panels or

removing warmer plates on this

brew may expose uninsulated

electrical components.

Disconnect brewer from

electrical power before

removing any panel or warmer

plate.

ACCESS PANELS

TOP PANEL:

Remove top panel to access hot water tank, thermo probe,

heating elements, brew circuit tubing, faucet valve and piping.

Top panel is held by two screws at the rear and a retaining lip at

the front.

FRONT PANEL:

Upper front panel is held by two screws at the bottom and a

retaining lip at the top. Lower panels are held by retaining clips

under the warmer plates.

Remove front panel to access controller and power board.

Solenoid on Models 1040 & 1072 are accessible through the

front panel.

WARMER ELEMENTS:

Warmer plates screw to the bracket, and are locked by a nut from

below. For lower warmers, remove the appropriate hole plug to

access the nut. For top panel warmers, remove the top panel to

access the nut. Remove the warmer plate to access the warmer

element.

Fig. 13 Access Panels

641 p/n 2M-75844 1012 1040 1072 Owmers Manual

IL2207

enin

SERVICING INSTRUCTIONS (continued)

TEMPERATURE ADJUSTMENT

Unplug power cord or turn circuit breaker OFF. Remove top

panel. Remove button plug from front panel.

Pull vent tube out of tank lid and insert a thermometer of known

accuracy in vent hole. Reconnect brewer to electrical power.

Place empty container under brew chamber. Energize brewer

and pour one decanter (64 oz.) of cold water into pour-over

opening. When HEAT light goes out, read the temperature

displayed on thermometer.

Adjust WATER TEMP dial on controller; clockwise increases

temperature. Refer to Table 1 below for proper brewing

temperature based on altitude.

Upon completion, remove thermometer and reinstall vent tube.

Fig. 14 Checking and Adjusting Brew Temperature

CAUTION:

SHOCK HAZARD

These procedures involve

exposed electrical circuits.

These procedures are to

EHSHUIRUPHGE\TXDOL¿HG

technical personnel only.

NOTE: Optimum brewing

temperature is 195ºF to 205ºF

(90ºC to 96ºC).

Maximum temperature setting

should be no more than 205ºF

(96ºC).

IMPORTANT:

An electronic temperature con-

troller will maintain temperature

within ±2ºF.

To prevent boiling water in

the brewer, controller should

be adjusted to a maximum

temperature equal to the local

boiling temperature minus 2ºF,

or 205ºF, whichever is less.

641 p/n 2M-75844 1012 1040 1072 Owmers Manual

Table 1 Boiling Temperature by Altitude

ELEVATION (feet above seal level)

(

)

195

200

205

210

190

IDEAL

BREWING

TEMPERATURE

RANGE

MAXIMUM

TEMPERATURE

SETTING

BOILING

POINT OF

WATER

IL2208

IL2209

SERVICING INSTRUCTIONS (continued)

IMPORTANT: Water pressure

must be between 20 p.s.i and

SVLÀRZLQJSUHVVXUH,I

water pressure exceeds this

YDOXHRULIZDWHUSUHVVXUH

YDULHVJUHDWOy, a pressure

UHJXODWRUPXVWEHLQVWDOOHGLQ

the water supply line.

IMPORTANT: %HIRUHVHWWLQJ

DVVHPEO\LQWRWDQNPDNHVXUH

WDQNOLGJDVNHWLVSURSHUO\

VHDWHGRQÀDQJHRIOLG

DO NOT OVER-TIGHTEN.

IMPORTANT: :KHQUHSODFLQJ

WHPSHUDWXUHSUREHEHVXUHD

new seal washer is in place

DURXQGWKHSUREH TLJKWHQMDPE

ORFNQXWRQO\HQRXJKWRHQVXUH

QRZDWHUOHDNDJH([FHVVLYH

WLJKWHQLQJLVQRWQHFHVVDUy.

IMPORTANT: :KHQUHSODFLQJ

KHDWLQJHOHPHQWDOVRUHSODFH

VHDOJDVNHWV

BREW TIME ADJUSTMENT

7KHDPRXQWRIZDWHUGLVSHQVHGDXWRPDWLFDOO\GXULQJDEUHZF\FOH

LVFRQWUROOHGE\WKH62/(12,' 7,0(GLDORIWKHFRQWUROOHr.

Place empty decanter under brew chamber3UHVV%5(:

EXWWRQ%UHZHUVKRXOGGLVSHQVHRQHIXOOGHFDQWHURIZDWHr.

TRDGMXVWDPRXQW

5HPRYHEUHZFKDPEHUDQGEXWWRQSOXJ2QWKHFRQWUROOHrDGMXVW

62/(12,' 7,0(GLDO%5(: 7,0(FORFNZLVHLQFUHDVHVWLPH

5XQVHYHUDOF\FOHVWRFKHFNDPRXQWRIZDWHUGHOLYHUHG

DRIPOUT TIME ADJUSTMENT

WDWHUGHOLYHUHGWRWKHEUHZFKDPEHUZLOOWDNHDZKLOHWRGULS

WKURXJKDVFRIIHH 7KHWLPHEHWZHHQWKHHQGRIDEUHZDQG

ZKHQDQHZEUHZFDQEHLQLWLDWHGLVFRQWUROOHGE\WKH%5(:

6,*1$/ 7,0(5 $GMXVWWKH%5(:6,*1$/ 7,0(5GLDORQWKH

FRQWUROOHUWRDFFRXQWIRUWKHGULSRXWWLPH5HSODFHEXWWRQSOXJ

REMOVE TANK LID ASSEMBLY

8QSOXJEUHZHURUWXUQFLUFXLWEUHDNHUOFF. Turn OFF water

supply5HPRYHWRSSDQHO3XOOYHQWWXEHDQGLQOHWHOERZRXWRI

basin pan.

2QDXWRPDWLFPRGHOVSXOOZDWHULQOHWWXEHRXWRIEDVLQSDQ

5HPRYHEDVLQSDQ

2QPRGHOVZLWKIDXFHWGLVFRQQHFWLQOHWSLSHDWIDXFHWVKXWRII

YDOYHDQGRXWOHWSLSHDWIDXFHW

'LVFRQQHFWDOOZLULQJIURPKLOLPLWDQGKHDWLQJHOHPHQW

'LVFRQQHFWWHPSHUDWXUHSUREHIURPFRQWUROOHr.

/RRVHQFHQWHUVFUHZRQWDQNKROGGRZQEUDFNHW5HPRYH

KROGGRZQEUDFNHWE\VOLGLQJVKRUWVORWWHGHQGRIIRIORFNLQJVWXG

DQGOLIWLQJLWRII 5HPRYHFRYHUDVVHPEO\E\OLIWLQJLWVWUDLJKWXS

5HDVVHPEOHLQUHYHUVHRUGHr.

REPLACE TEMPERATURE PROBE

8QSOXJEUHZHURUWXUQFLUFXLWEUHDNHUOFF5HPRYHWRSSDQHO

/RRVHQDQGIUHHMDPQXWIURPSDVVWKUX¿WWLQJVHFXULQJ

WHPSHUDWXUHSUREH'LVFRQQHFWWHPSHUDWXUHSUREHZLULQJ

FRQQHFWRUIURPFRQWUROOHr.

/LIWRXWSUREHMDPEQXWDQGJDVNHW

5HDVVHPEOHLQUHYHUVHRUGHr.

REPLACE HEATING ELEMENT

5HPRYHWDQNOLGDVVHPEO\SHUDERYH

5HPRYHWZRKH[QXWVKROGLQJHOHPHQWWRFRYHr. Pull element

IURPPRXQWLQJKROHV

5HDVVHPEOHLQUHYHUVHRUGHr.

Fig. 15 Adjust BrewTime

and Dripout Time

,/

BREW TIME

DRIPOUT TIME

TER

(°

)

SOLENOID TIMER

(WATER VOLUME)

(SECONDS)

BREW SIGNAL TIMER

- BREW LIGHT

END OF BREW BEEPER

(MINUTES)

185

190

195

200

205

641 p/n 2M-75844 1012 1040 1072 Owmers Manual

SERVICING INSTRUCTIONS (continued)

REPLACE SOLENOID

Unplug power cord. Turn OFF and disconnect water supply from

EUHZHULQOHW¿WWLQJ

Remove front panel. Remove two screws holding access door in

SODFH5HPRYHDFFHVVGRRUDQGVROHQRLG8QVFUHZLQOHW¿WWLQJ

cap to release solenoid from door.

Remove wiring from solenoid.

Large end of wrench 86660 can be used to hold solenoid inlet

¿WWLQJZKLOHGLVFRQQHFWLQJVXSSO\OLQH

REPLACE FAUCET SUPPLY HOSE

Unplug power cord. Turn OFF and disconnect water supply from

EUHZHULQOHW¿WWLQJ'LVFRQQHFWKRVH¿WWLQJIURPVROHQRLG6HH

illustration at right).

'LVFRQQHFWKRVHÀDUH¿WWLQJIURPWDQNFRLO¿WWLQJ

REPLACE HOT WATER FAUCET COIL

6\PSWRP%UHZHUGULSVFRQWLQXRXVO\IURPEUHZKHDGH[FHSW

when faucet valve is turned OFF.)

IMPORTANT: :KHQUHSODFLQJZDWHUIDXFHWFRLODOVRUHSODFH

VHDOJDVNHWV

5HPRYHWDQNOLGDVVHPEO\SHUDERYH

5HPRYHWZRKH[QXWVKRWZDWHUFRLOWRFRYHr. Pull coil from

mounting holes.

REPAIR HOT WATER FAUCET

Remove top panel and turn faucet valve OFF.

Unscrew aerator cap from faucet and remove handle retaining

FOLS'RQRWOHWIDXFHWERG\WXUQ

Pull bonnet assembly from faucet body.

([DPLQHWKHLQWHULRURIWKHIDXFHWERG\DQGWKHVXUIDFHRIWKH

seat cup. Clean out any debris in the faucet bodyXVLQJDVWLff

bristle brush if necessary.

NOTE: $Q\DEUDVLRQRUURXJKQHVVRQWKHÀDWHQGRIWKHVHDW

FXSZLOOUHTXLUHUHSODFLQJWKHVHDWFXS

WRUNWKHVHDWFXSRXWRIWKHERQQHWDQGRff of the end of the

stem.

,QVWDOODQHZVHDWFXSPDNLQJVXUHWKHNQRERQWKHVWHPLVIXOO\

LQVHUWHGLQWRWKHSRFNHWRIWKHVHDWFXSDQGWKHVNLUWRIWKHVHDW

cup is fully inserted into the bonnet.

([DPLQHWKHDHUDWRr&OHDQDQ\GHEULVIURPWKHVFUHHQRUÀRZ

straightenerXVLQJDVWLff bristle brush if necessary.

Fig. 16 Fill Solenoid

Fig. 17 86660 Solenoid Wrench

P/N 2C-76660 Braided Hose Wrench

BYPASS

OUTLET

5/8” for VALVE

FLARE FITTING

7/16” for

BRAIDED HOSE

METAL FITTING

2C-76660 WRENCH

WRENCH

METAL FITTING

CLINCH RING

SLIDE WRENCH BETWEEN

VALVE AND HOSE FITTING

PRESS CLINCH RING TOWARD

METAL FITTING TO RELEASE

WHITE

CLINCH

RING

IL2619

641 p/n 2M-75844 1012 1040 1072 Owmers Manual

SCREEN

SOLENOID

WASHER

INLET

FITTING

CAP

IL1693a

Fill

Solenoid

REPLACE HOT WATER FAUCET COIL

(Symptom: Brewer drips continuously from brew head, except

when faucet valve is turned OFF.)

Remove tank lid assembly per above.

Remove two hex nuts hot water coil to cover. Pull coil from

mounting holes.

Reassemble in reverse order.

REPAIR HOT WATER FAUCET

Remove top panel and turn faucet valve OFF.

Unscrew aerator cap from faucet and remove handle retaining

clip. Do not let faucet body turn.

Pull bonnet assembly from faucet body.

Examine the interior of the faucet body and the surface of the

seat cup. Clean out any debris in the faucet body, using a stiff

bristle brush if necessary.

Examine the aerator&OHDQDQ\GHEULVIURPWKHVFUHHQRUÀRZ

straightener, using a stiff bristle brush if necessary.

Reassemble in reverse order.

REPLACE CONTROLLER

Unplug power cord or turn circuit breaker OFF.

Remove front panel. Remove timer faceplate. Use needle

QRVHSOLHUVWRGLVHQJDJHWKUHHEDUEHG¿WWLQJVKROGLQJFRQWUROOHU

to bracket. Disconnect keypad ribbon cable (note position “1”),

temperature probe and power board cable.

Set jumpers as described on page 19.

Reassemble in reverse order.

Adjust controller as described on pages 15 & 16.

IMPORTANT: When replacing

water faucet coil, also replace

seal gaskets.

NOTE: Any abrasion or

URXJKQHVVRQWKHÀDWHQGRIWKH

seat cup will require replacing

the seat cup:

Work the seat cup out of the

bonnet and off of the end of the

stem.

Install a new seat cup, making

sure the knob on the stem is

fully inserted into the pocket of

the seat cup, and the skirt of the

seat cup is fully inserted into the

bonnet.

REPLACE

TER

AUCET COIL

IMPOR

When replacing

SERVICING INSTRUCTIONS (continued)

Fig. 18 Controller Hook-Up

IL2620

KEYPAD

RIBBON

CABLE

TEMP

PROBE

POWER

BOARD

CONNECTOR

641 p/n 2M-75844 1012 1040 1072 Owmers Manual

La page charge ...

Bloomfield EBC™ 3 Warmer Brewer Le manuel du propriétaire

Marque: Bloomfield

Modèle: EBC™ 3 Warmer Brewer

Catégorie: Cafetières

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Bloomfield EBC™ 3 Warmer Brewer Owner's manual

Bloomfield EBC™ 3 Warmer Brewer Le manuel du propriétaire

Ce manuel convient également à

Bloomfield EBC™ 3 Warmer Brewer Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents