Kenwood KDC-202MR Manuel utilisateur

Take the time to read through this instruction manual. Familiarity with installa-

tion and operation procedures will help you obtain the best performance from

your new CD-receiver.

For your records

Record the serial number, found on the back of the unit, in the spaces designated on

the warranty card, and in the space provided below. Refer to the model and serial

numbers whenever you call upon your KENWOOD dealer for information or service on

the product.

Model KDC-2022, KDC-2022V, KDC-202MR, KDC-222, KDC-222S,

KDC-122, KDC-122S Serial number

KDC-2022

KDC-2022V

KDC-202MR

KDC-222

KDC-222S

KDC-122

KDC-122S

CD-RECEIVER

INSTRUCTION MANUAL

AMPLI-TUNER-LECTEUR DE CD

MODE D’EMPLOI

RECEPTOR DE CD

MANUAL DE INSTRUÇÕES

REPRODUCTOR DE DISCOS COMPACTOS RECEPTOR DE FM/AM

MANUAL DE INSTRUCCIONES

KDC-2022/202/122(K)Cover 02.9.26 3:20 PM Page 1

— 2 —

English

Contents

Safety precautions......................3

About CDs...................................5

General features .........................6

Power

Selecting the Source

Volume

Attenuator

Loudness

System Q

Audio Control

Speaker Setting

Clock Display

Adjusting Clock

DSI (Disabled System Indicator)

Theft Deterrent Faceplate

Tuner features .............................9

Tuning Mode

Tuning

Station Preset Memory

Auto Memory Entry

Preset Tuning

CRSC (Clean Reception System Circuit)

CD/External disc control

features ..................................11

Playing CD

Playing External Disc

Fast Forwarding and Reversing

Track Search

Album Search

Track/Album Repeat

Track Scan

Random Play

Magazine Random Play

Direct Track Search

Direct Album Search

Basic Operations of remote......14

Loading and Replacing the battery

Basic operations

In Tuner source

In Disc source

Accessories ...............................16

Installation Procedure ..............16

Connecting Wires to Terminals 17

Installation ................................18

Troubleshooting Guide .............20

Specifications ...........................23

Warning .....................................24

KDC-2022/122_U.S 02.9.26 3:20 PM Page 2

— 3 —

Safety precautions

To prevent injury or fire, take the

following precautions:

• Insert the unit all the way in until it is fully

locked in place. Otherwise it may fall out of

place when jolted.

• When extending the ignition, battery, or

ground wires, make sure to use automotive-

grade wires or other wires with a 0.75mm

2

(AWG18) or more to prevent wire

deterioration and damage to the wire

coating.

•To prevent a short circuit, never put or leave

any metallic objects (such as coins or metal

tools) inside the unit.

• If the unit starts to emit smoke or strange

smells, turn off the power immediately and

consult your Kenwood dealer.

• Make sure not to get your fingers caught

between the faceplate and the unit.

• Be careful not to drop the unit or subject it to

strong shock.

The unit may break or crack because it

contains glass parts.

• Do not touch the liquid crystal fluid if the

LCD is damaged or broken due to shock. The

liquid crystal fluid may be dangerous to your

health or even fatal.

If the liquid crystal fluid from the LCD

contacts your body or clothing, wash it off

with soap immediately.

2WARNING

To prevent damage to the machine,

take the following precautions:

• Make sure to ground the unit to a negative

12V DC power supply.

• Do not open the top or bottom covers of the

unit.

• Do not install the unit in a spot exposed to

direct sunlight or excessive heat or humidity.

Also avoid places with too much dust or the

possibility of water splashing.

• Do not set the removed faceplate or the

faceplate case in areas exposed to direct

sunlight, excessive heat or humidity. Also

avoid places with too much dust or the

possibility of water splashing.

•To prevent deterioration, do not touch the

terminals of the unit or faceplate with your

fingers.

• Do not subject the faceplate to excessive

shock, as it is a piece of precision

equipment.

• When replacing a fuse, only use a new one

with the prescribed rating. Using a fuse with

the wrong rating may cause your unit to

malfunction.

•To prevent a short circuit when replacing a

fuse, first disconnect the wiring harness.

• Do not place any object between the

faceplate and the unit.

• Do not use your own screws. Use only the

screws provided. If you use the wrong

screws, you could damage the unit.

2CAUTION

IMPORTANT INFORMATION

About CD players/disc changers

connected to this unit

KENWOOD disc changers/ CD players

released in 1998 or later can be connected to

this unit.

Refer to the catalog or consult your Kenwood

dealer for connectable models of disc

changers/ CD players.

Note that any KENWOOD disc changers/ CD

players released in 1997 or earlier and disc

changers made by other makers cannot be

connected to this unit.

Unsupported connection may result in

damage.

Setting the "O-N" Switch to the "N" position for

the applicable KENWOOD disc changers/ CD

players.

The functions that can be used and the

information that can be displayed will differ

depending on the models being connected.

You can damage both your unit and the CD

changer if you connect them incorrectly.

Do Not Load 3-in. CDs in the CD slot

If you try to load a 3 in. CD with its adapter

into the unit, the adapter might separate from

the CD and damage the unit.

KDC-2022/122_U.S 02.9.26 3:20 PM Page 3

— 4 —

English

Safety precautions

• If you experience problems during

installation, consult your Kenwood dealer.

• If the unit does not seem to be working

right, try pressing the reset button first. If

that does not solve the problem, consult

your Kenwood dealer.

•Press the reset button if the Disc auto

changer fails to operate correctly. Normal

operatin should be restored.

• Characters in the LCD may become difficult

to read in temperatures below 41 ˚F (5 ˚C).

• The illustrations of the display and the panel

appearing in this manual are examples used

to explain more clearly how the controls are

used. Therefore, what appears on the display

in the illustrations may differ from what

appears on the display on the actual

equipment, and some of the illustrations on

the display may represent something

impossible in actual operation.

NOTE

Reset button

Cleaning the Faceplate Terminals

If the terminals on the unit or faceplate get

dirty, wipe them with a dry, soft cloth.

Cleaning the Unit

If the faceplate of this unit is stained, wipe it

with a dry soft cloth such as a silicon cloth.

If the faceplate is stained badly, wipe the stain

off with a cloth moistened with neutral

cleaner, then wipe neutral detergent off.

Applying spray cleaner directly to the unit may

affect its mechanical parts. Wiping the

faceplate with a hard cloth or using a volatile

liquid such as thinner or alcohol may scratch

the surface or erases characters.

Cleaning the CD Slot

As dust tends to accumulate in the CD slot,

clean it every once in a while. Your CDs can

get scratched if you put them in a dusty CD

slot.

Lens Fogging

Right after you turn on the car heater in cold

weather, dew or condensation may form on

the lens in the CD player of the unit. Called

lens fogging, CDs may be impossible to play.

In such a situation, remove the disc and wait

for the condensation to evaporate. If the unit

still does not operate normally after a while,

consult your Kenwood dealer.

KDC-2022/122_U.S 02.9.26 3:20 PM Page 4

— 5 —

About CDs

Handling CDs

• Don’t touch the recording surface of the CD.

• CD-R and CD-RW are easier to damage than

a normal music CD. Use a CD-R or a CD-RW

after reading the caution items on the

package etc.

• Don’t stick tape etc. on the CD.

Also, don’t use a CD with tape stuck on it.

When using a new CD

If the CD center hole or outside rim has burrs,

use it after removing them with a ball pen etc.

CD accessories

Don’t use disc type accessories.

CD cleaning

Clean from the center of the disc and move

outward.

Removing CDs

When removing CDs from this unit pull them

out horizontally.

CDs that can’t be used

• CDs that aren’t round can’t be used.

• CDs with coloring on the recording surface

or that are dirty can’t be used.

• This unit can only play the CDs with

.

It may not correctly play discs which do not

have the mark.

•A CD-R or CD-RW that hasn’t been finalized

can’t be played. (For the finalization process

refer to your CD-R/CD-RW writing software,

and your CD-R/CD-RW recorder instruction

manual.)

CD storage

• Don’t place them in direct sunlight (On the

seat or dashboard etc.) and where the

temperature is high.

• Store CDs in their cases.

Burrs

KDC-2022/122_U.S 02.9.26 3:20 PM Page 5

— 6 —

English

Turning the volume down quickly.

Press the [ATT] button.

Each time the button is pressed the Attenuator turns ON or OFF.

When it’s ON, the "ATT" indicator blinks.

Attenuator

Increasing Volume

Press the [u] button.

Decreasing Volume

Press the [d] button.

Volume

Press the [SRC] button.

Source required Display

Tuner "TUnE"

CD "CD"

External disc "DISC"

(Function of the KDC-2022/KDC-2022V/KDC-202MR)

Standby (Illumination only mode) "OFF"

Selecting the Source

Turning ON the Power

Press the [SRC] button.

Turning OFF the Power

Press the [SRC] button for at least 1 second.

Power

General features

— 6 —

AM FM

Q/CLK/

AUDADJ

ATT/

LOUD

SRC #1 #3

¢4ud

KDC-2022/KDC-2022V/KDC-202MR

ATT indicator

LOUD indicator

ATT indicator

LOUD indicator

SYSTEM Q indicator

Release button

(KDC-2022/KDC-2022V/KDC-202MR/

KDC-222/KDC-222S only)

KDC-222/KDC-222S/KDC-122/KDC-122S

Clock indicator

Clock display

Clock indicator

Clock display

KDC-2022/122_U.S 02.9.26 3:20 PM Page 6

— 7 —

1 Select the source for adjustment

Press the [SRC] button.

2 Enter Audio Control mode

Press the [AUD] button for at least 1 second.

3 Select the Audio item for adjustment

Press the [FM] or [AM] button.

Each time the button is pressed the items that can be adjusted

switch as shown below.

4 Adjust the Audio item

Press the [4] or [¢] button.

Adjustment Item Display Range

Bass level "BAS" –8 — +8

Middle level "MID" –8 — +8

Treble level "TRE" –8 — +8

Balance "BL" Left 15 — Right 15

Fader "FD" Rear 15 — Front 15

5 Exit Audio Control mode

Press the [AUD] button.

Audio Control

You can recall the best sound setting preset for different types of

the music.

1 Select the source to set

Press the [SRC] button.

2 Select the Sound type

Press the [Q] button.

Each time the button is pressed the sound setting switches.

Sound setting Display

Flat "SQ-1"

Rock "SQ-2"

Top 40 "SQ-3"

Pops "SQ-4"

Jazz "SQ-5"

Easy "SQ-6"

• Each setting value is changed with the <Speaker setting> (page

8).

First, select the speaker type with the Speaker setting.

• When the System Q setting is changed, the Bass, Middle, and

Treble set in audio control replace the System Q values.

System Q

Compensating for low and high tones during low volume.

Press the [LOUD] button for at least 1 second.

Each time the button is pressed for at least 1 second the

Loudness turns ON or OFF.

When it’s ON, "LOUD" indicator is ON.

Loudness

KDC-2022/122_U.S 02.9.26 3:20 PM Page 7

Function of the KDC-2022/KDC-2022V/KDC-202MR/KDC-222/KDC-222S

A red indicator will blink on the unit after the faceplate is

removed, warning potential thieves.

1 Turn the power OFF

Press the [SRC] button for at least 1 second.

2 Set the DSI

While pressing the [#1] and [#3] button, press the [SRC]

button.

Each time the step 1 and 2 operation is done the DSI turns ON or

OFF.

DSI (Disabled System Indicator)

1 Select the clock display

Press the [CLK] button.

2 Enter clock adjustment mode

Press the [CLK] button for at least 2 seconds.

The clock display blinks.

3 Adjust the hours

Press the [FM] or [AM] button.

Adjust the minutes

Press the [4] or [¢] button.

4 Exit clock adjustment mode

Press the [CLK] button.

Adjusting Clock

Press the [CLK] button.

Each time the button is pressed the clock display turns ON or

OFF.

When it’s ON, the clock indicator is ON.

Clock Display

Fine-tuning so that the System Q value is optimal when setting

the speaker type.

1 Enter Standby

Press the [SRC] button.

Select the "OFF" display.

2 Enter Speaker Setting mode

Press the [Q] button.

3 Select the Speaker type

Press the [4] or [¢] button.

Each time the button is pressed the setting switches as shown

below.

Speaker type Display

OFF "SP-F"

For the OEM speaker "SP-O"

For 6 & 6x9 in. speaker "SP-6"

For 5 & 4 in. speaker "SP-5"

4 Exit Speaker Setting mode

Press the [Q] button.

Speaker Setting

General features

— 8 —

English

KDC-2022/122_U.S 02.9.26 3:20 PM Page 8

— 9 —

Function of the KDC-2022/KDC-2022V/KDC-202MR/KDC-222/KDC-222S

The faceplate of the unit can be detached and taken with you,

helping to deter theft.

Removing the Faceplate

Press the Release button.

The faceplate is unlocked, allowing you to detach it.

• The faceplate is a precision piece of equipment and can be

damaged by shocks or jolts. For that reason, keep the faceplate in

its special storage case while detached.

• Do not expose the faceplate or its storage case to direct sunlight

or excessive heat or humidity. Also avoid places with too much

dust or the possibility of water splashing.

Reattaching the Faceplate

1 Align the projections on the unit with the grooves on the

faceplate.

2 Push the faceplate in until it clicks.

The faceplate is locked in place, allowing you to use the unit.

Theft Deterrent Faceplate

Tuner features

AM

CRSC

FM/

AUTO/

AME

#1 - 6SRC

¢4

KDC-2022/KDC-2022V/KDC-202MR

KDC-222/KDC-222S/KDC-122/KDC-122S

ST indicator

Band display

Preset station number

Frequency display

AUTO indicator

ST indicator

Band display

Preset station number

Frequency display

AUTO indicator

CRSC indicator

KDC-2022/122_U.S 02.9.26 3:20 PM Page 9

Calling up the stations in the memory.

1 Select the band

Press the [FM] or [AM] button.

2 Call up the station

Press the [#1] — [#6] button.

Preset Tuning

Putting stations with good reception in the memory

automatically.

1 Select the band for Auto Memory Entry

Press the [FM] or [AM] button.

2 Open Auto Memory Entry

Press the [AME] button for at least 2 seconds.

When 6 stations that can be received are put in the memory

Auto Memory Entry closes.

Auto Memory Entry

1 Select the band

Press the [FM] or [AM] button.

2 Select the frequency to put in the memory

Press the [4] or [¢] button.

3 Put the frequency in the memory

Press the [#1] — [#6] button for at least 2 seconds.

The preset number display blinks 1 time.

On each band, 1 station can be put in the memory on each [#1]

— [#6] button.

Putting the station in the memory.

Station Preset Memory

Selecting the station.

1 Select tuner source

Press the [SRC] button.

Select the "TUnE" display.

2 Select the band

Press the [FM] or [AM] button.

Each time the [FM] button is pressed it switches between the

FM1, FM2, and FM3 bands.

3 Tune up or down band

Press the [4] or [¢] button.

During reception of stereo stations the "ST" indicator is ON.

Tuning

Choose the tuning mode.

Press the [AUTO] button.

Each time the button is pressed the Tuning mode switches as

shown below.

Tuning mode Display Operation

Auto seek "AUTO 1" Automatic search for a station.

indicator

Preset station "AUTO 2" Search in order of the stations

seek indicator in the Preset memory.

Manual — Normal manual tuning control.

Tuning Mode

Tuner features

— 10 —

English

KDC-2022/122_U.S 02.9.26 3:20 PM Page 10

— 11 —

Temporarily have reception switched from stereo to mono to

reduce multi-path noise when listening to the FM station.

Press the [CRSC] button for at least 1 second.

Each time the button is pressed CRSC turns ON or OFF.

When it's ON, the CRSC indicator is ON.

CRSC (Clean Reception System Circuit)

DISC- DISC+

REP

RDM

SCAN

M.RDMSRC

¢40

KDC-2022/KDC-2022V/KDC-202MR

KDC-222/KDC-222S/KDC-122/KDC-122S

RDM indicator

SCN indicator

REP indicator

Track time

Track number

IN indicator

RDM indicator

SCN indicator

REP indicator

Track number

IN indicator

Disc number

Track time

CD/External disc control features

KDC-2022/122_U.S 02.9.26 3:20 PM Page 11

Replaying the song/disc you're listening to.

Press the [REP] button.

Each time the button is pressed the Repeat Play switches as

shown below.

Repeat play Display

Track Repeat "REP" indicator & Track No. blink.

Album Repeat "REP" indicator & Disc No. blink.

(Function of disc changer)

OFF —

Track/Album Repeat

Function of the KDC-2022/KDC-2022V/KDC-202MR

Selecting the disc you want to hear.

Press the [DISC–] or [DISC+] button.

Album Search (Function of disc changer)

Selecting the song you want to hear.

Press the [4] or [¢] button.

Track Search

Hold down on the [¢] button.

Release your finger to play the disc at that point.

Reversing

Hold down on the [4] button.

Release your finger to play the disc at that point.

Fast Forwarding

Fast Forwarding and Reversing

Function of the KDC-2022/KDC-2022V/KDC-202MR

Playing discs set in the optional accessory disc player connected

to this unit.

Press the [SRC] button.

Select the display for the disc player you want.

Display examples:

Display Disc player

"CD-2" CD player

"DISC" CD changer

"DISC" MD changer

• Disc #10 is displayed as "0".

• The functions that can be used and the information that can be

displayed will differ depending on the external disc players being

connected.

Playing External Disc

When a CD is inserted

Press the [SRC] button.

Select the "CD" display.

When a CD is inserted, the "IN" indicator is ON.

Eject the CD

Press the [0] button.

3 in. (8cm) CD cannot be played. Using an adapter and inserting

them into this unit can cause damage.

Playing CD

CD/External disc control features

— 12 —

English

KDC-2022/122_U.S 02.9.26 3:20 PM Page 12

— 13 —

When it's ON, the "RDM" indicator is ON and the track and disc

number blink.

When the [¢] button is pressed, the next song select starts.

Function of the KDC-2022/KDC-2022V/KDC-202MR

Play the songs on all the discs in the disc changer in random

order.

Press the [M.RDM] button.

Each time the button is pressed the Magazine Random Play turns

ON or OFF.

Magazine Random Play

(Function of disc changer)

Playing all the songs on the disc in random order.

Press the [RDM] button.

Each time the button is pressed Random Play turns ON or OFF.

When it's ON, the "RDM" indicator is ON and the track number

blinks.

When the [¢] button is pressed, the next song select starts.

Random Play

Playing the first part of each song on the disc you are listening

to and searching for the song you want to listen to.

1 Start Track Scan

Press the [SCAN] button.

"SCN" indicator is ON.

2 Release it when the song you want to listen to is played

Press the [SCAN] button.

Track Scan

Doing Track Search by entering the track number.

1 Enter the track number

Press the number buttons on the remote.

2 Do Track Search

Press the [4] or [¢] button.

Canceling Direct Track Search

Press the [38] button.

Direct Track Search (Function of remote)

Doing Disc Search by entering the disc number.

1 Enter the disc number

Press the number buttons on the remote.

2 Do Album Search

Press the [DISC+] or [DISC–] button.

Canceling Direct Album Search

Press the [38] button.

Input "0" to select disc 10.

Direct Album Search

(Function of disc changers with remote)

Function of the KDC-2022/KDC-2022V

KDC-2022/122_U.S 02.9.26 3:20 PM Page 13

[VOL.] buttons

Adjusting the volume.

[SRC] button

Each time the button is pressed the source switches.

For the source switching order refer to <Selecting the Source>

(page 6).

[ATT] button

Turning the volume down quickly.

When it is pressed again it returns to the previous level.

Basic operations

Use one lithium battery (CR2025).

Insert the batteries with the + and – poles aligned properly,

following the illustration inside the case.

Store unused batteries out of the reach of children. Contact a doctor

immediately if the battery is accidentally swallowed.

Do not set the remote on hot places such as above the dashboard.

2WARNING

Loading and Replacing the battery

[#0] — [#9]

FM/AM/DISC

+

/DISC–

ATT

38

4/¢

VOL.

SRC

Accessory of the KDC-2022/KDC-2022V

Basic Operations of remote

— 14 —

English

Not used

KDC-2022/122_U.S 02.9.26 3:20 PM Page 14

— 15 —

[4]/ [¢] buttons

Doing track forward and backward.

[DISC+]/ [DISC–] buttons

Doing album forward and backward.

[38] button

Each time the button is pressed the song pauses and plays.

[#0] — [#9] buttons

When in <Direct Track Search> (page 13) and <Direct Album

Search> (page 13), enter the track/disc number.

In Disc source

[FM]/ [AM] buttons

Select the band.

Each time the [FM] button is pressed it switches between the

FM1, FM2, and FM3 bands.

[4]/ [¢] buttons

Tune up or down band.

[#0] — [#9] buttons

Press buttons [#1] — [#6] to recall preset stations.

In Tuner source

KDC-2022/122_U.S 02.9.26 3:20 PM Page 15

English

— 16 —

The use of any accessories except for those provided might result in

damage to the unit. Make sure only to use the accessories shipped with

the unit, as shown above.

1. To prevent a short circuit, remove the key from the ignition and

disconnect the - battery.

2. Make the proper input and output wire connections for each unit.

3. Connect the speaker wires of the wiring harness.

4. Connect the wiring harness wires in the following order: ground,

battery, ignition.

5. Connect the wiring harness connector to the unit.

6. Install the unit in your car.

7. Reconnect the - battery.

8. Press the reset button.

If you connect the ignition wire (red) and the battery wire (yellow)

to the car chassis (ground), you may cause a short circuit, that in

turn may start a fire. Always connect those wires to the power

source running through the fuse box.

• If your car's ignition does not have an ACC position, connect the

ignition wires to a power source that can be turned on and off

with the ignition key. If you connect the ignition wire to a power

source with a constant voltage supply, as with battery wires, the

battery may die.

• If the console has a lid, make sure to install the unit so that the

faceplate will not hit the lid when closing and opening.

• If the fuse blows, first make sure the wires aren’t touching to

cause a short circuit, then replace the old fuse with one with the

same rating.

• Insulate unconnected wires with vinyl tape or other similar

material. To prevent a short circuit, do not remove the caps on

the ends of the unconnected wires or the terminals.

• Connect the speaker wires correctly to the terminals to which

they correspond. The unit may be damaged or fail to work if you

share the - wires or ground them to any metal part in the car.

• When only two speakers are being connected to the system,

connect the connectors either to both the front output terminals

or to both the rear output terminals (do not mix front and rear).

For example, if you connect the + connector of the left speaker

to a front output terminal, do not connect the - connector to a

rear output terminal

• After the unit is installed, check whether the brake lamps,

blinkers, wipers, etc. on the car are working properly.

•Mount the unit so that the mounting angle is 30° or less.

2CAUTION

2WARNING

Accessories

Installation Procedure

.........1

1

3

5

External view

......... Number of items

External view

......... Number of items

.........4

4

.........2

2

.........4

.........1

(KDC-2022/KDC-2022V/

KDC-222/KDC-222S only)

KDC-2022/122_U.S 02.9.26 3:20 PM Page 16

— 17 —

P.CONT

ANT.

CONT.

FRONT • L

FRONT • R

REAR • L

REAR • R

–

+

REAR

L

R

FM/AM antenna input 1

Rear left output (White) 23

Rear right output (Red) 28

Fuse (10A) 24

2 KENWOOD disc changer control input (KDC-2022/2022V/202MR only)

Wiring harness

(Accessory1)25

29

White/Black

32

Gray/Black

35

Green/Black

38

Purple/Black

White

31

Gray

34

Green

37

Purple

40

To front left

speaker 30

To front right

speaker 33

To rear right

speaker 39

To rear left

speaker 36

Ignition wire (Red) 20

Battery wire (Yellow) 21

Ground wire (Black) · (To car chassis) 22

Ignition key

switch

10

Car fuse box

(Main fuse)

11

ACC 13

Car fuse

box 14

Battery 12

If no connections are made, do not let the wire come out from the tab.

4

Front left output (White) (KDC-2022/2022V/202MR only) 26

Front right output (Red) (KDC-2022/2022V/202MR only) 27

To connect the Disc changer, consult

your Disc changer manual. 3

Connecting Wires to Terminals

Power control/Motor antenna

control wire (Blue/White)

16

6 Connect either to the power control terminal

when using the optional power amplifier, or to

the antenna control terminal in the vehicle.

Not Used 19

Do not let the wire come

out from the tab. 4b

KDC-2022/122_U.S 02.9.26 3:20 PM Page 17

Make sure that the unit is installed securely in place. If the unit is

unstable, it may malfunction (for example, the sound may skip).

Metal mounting strap

(commercially available)

Self-tapping screw

(commercially available)

Firewall or metal support

Screw (M4X8)

(commercially

available)

■ Installation

8 mm

MAX.

ø5mm

8mm

MAX.

■ Installing in Japanese-Made Cars

T: Toyota cars

N: Nissan cars

T

N

T

T/N

Accessory3...for Nissan car

Accessory4 ...for Toyota car

• During installation, do not use any screws except for those provided.

The use of different screws might result in damage to the main unit.

• Damage may occur if a screwdriver or similar tool is used with

excessive force during the installations.

1 Refer to the section "Removing the hard rubber frame" (page 19)

and then remove the hard rubber frame.

2 Align the holes in the unit (two locations on each side) with the

vehicle mounting bracket and secure the unit with the accessory

screws.

3

4

Bend the tabs of the

mounting sleeve

with a screwdriver or

similar utensil and

attach it in place.

Installation

Accessory5

■ Screwing the Faceplate on the Unit

(KDC-2022/KDC-2022V/KDC-222/KDC-222S only)

Never insert the taptite screw (ø4 × 16 mm) in any other screw hole

than the one specified. If you screw it in another hole, it will contact

and may cause damage to the mechanical parts inside the unit.

If you want to fasten the

faceplate to the main unit so

that it does not fall off,

screw in the provided screw

(ø4 X 16 mm) in the hole

shown below.

English

— 18 —

KDC-2022/122_U.S 02.9.26 3:20 PM Page 18

— 19 —

■ Removing the hard rubber frame

2 When the lower level is removed, remove the upper two

locations.

The frame can be removed from the top side in the same manner.

Catch

Lock

1 Engage the catch pins on the removal tool and remove the two

locks on the lower level.

Lower the frame and pull it forward as shown in the figure.

Accessory2

Removal tool

Accessory2

Removal tool

Screw (M4X8)

(commercially

available)

■ Removing the Unit

4 Lower the removal tool

toward the bottom, and pull

out the unit halfway while

pressing towards the inside.

Be careful to avoid injury from

the catch pins on the removal

tool.

5 Pull the unit all the way out

with your hands, being

careful not to drop it.

1 Refer to the section “Removing the hard rubber frame” and then

remove the hard rubber frame.

2 Remove the screw (M4 × 8) on the back panel.

3 Insert the two removal tools deeply into the slots on each side,

as shown.

KDC-2022/122_U.S 02.9.26 3:20 PM Page 19

English

— 20 —

Troubleshooting Guide

What might seem to be a malfunction in your unit may

just be the result of slight misoperation or miswiring.

Before calling service, first check the following table

for possible problems.

General

? The power does not turn ON.01

✔ The fuse has blown.

☞ After checking for short circuits in the wires, replace the fuse with

one with the same rating.

✔ No ACC position on vehicle ignition.02

☞ Connect the same wire to the ignition as the battery wire.

? Nothing happens when the buttons are pressed.04

✔ The computer chip in the unit is not functioning normally.

☞ Press the reset button on the unit (page 4).

? There’s a source you can’t switch.06

✔ There’s no CD inserted.

☞ Set the media you want to listen to. If there’s no media in this

unit, you can't swhich to each source.

? The memory is erased when the ignition is turned OFF.10

✔ The battery wire has not been connected to the proper terminal.

☞ Connect the wire correctly, referring to the section on

<Connecting Wires to Terminals>.

✔ The ignition and battery wire are incorrectly connected.11

☞ Connect the wire correctly, referring to the section on

<Connecting Wires to Terminals>.

? Even if Loudness is turned ON, high-pitched tone isn't compensated

for. 17

✔ Tuner source is selected.

☞ High-pitched tone isn't compensated for when in Tuner source.

? No sound can be heard, or the volume is low.

✔ The fader or balance settings are set all the way to one side.21

☞ Center the fader and balance settings.

✔ The input/output wires or wiring harness are connected incorrectly.22

☞ Reconnect the input/output wires or the wiring harness correctly.

See the section on <Connecting Wires to Terminals>.

? The sound quality is poor or distorted.25

✔ One of the speaker wires is being pinched by a screw in the car.

☞ Check the speaker wiring.

✔ The speakers are not wired correctly.27

☞ Reconnect the speaker wires so that each output terminal is

connected to a different speaker.

? The Touch Sensor Tone doesn’t sound.34

✔ The preout jack is being used.

☞ The Touch Sensor Tone can’t be output from the preout jack.

Tuner source

? Radio reception is poor.39

✔ The car antenna is not extended.

☞ Pull the antenna out all the way.

✔ The antenna control wire is not connected.40

☞ Connect the wire correctly, referring to the section on

<Connecting Wires to Terminals>.

KDC-2022/122_U.S 02.9.26 3:20 PM Page 20

La page charge ...

Kenwood KDC-202MR Manuel utilisateur

Kenwood KDC-202MR Manuel utilisateur

dans d''autres langues

Documents connexes