Extron TLP Pro 1520TG Manuel utilisateur

Taper
Manuel utilisateur
68-2294-01 Rev. D
01 19
TLP Pro 1220, TLP Pro 1520,
and TLP Pro 1720 Series
User Guide
TouchLink Pro Touchpanels
TouchLink Pro Touchpanel Control Systems
Safety Instructions • English
WARNING: This symbol,
D
, when used on the product, is intended
to alert the user of the presence of uninsulated dangerous voltage
within the product’s enclosure that may present a risk of electric shock.
ATTENTION: This symbol,
I
, when used on the product, is
intended to alert the user of important operating and maintenance
(servicing) instructions in the literature provided with the equipment.
For information on safety guidelines, regulatory compliances, EMI/EMF
compatibility, accessibility, and related topics, see the Extron Safety and
Regulatory Compliance Guide, part number 68-290-01, on the Extron
website, www.extron.com.
Sicherheitsanweisungen • Deutsch
WARNUNG: Dieses Symbol
D
auf dem Produkt soll den Benutzer
darauf aufmerksam machen, dass im Inneren des Gehäuses dieses
Produktes gefährliche Spannungen herrschen, die nicht isoliert sind
und die einen elektrischen Schlag verursachen können.
VORSICHT: Dieses Symbol
I
auf dem Produkt soll dem Benutzer
in der im Lieferumfang enthaltenen Dokumentation besonders wichtige
Hinweise zur Bedienung und Wartung (Instandhaltung) geben.
Weitere Informationen über die Sicherheitsrichtlinien, Produkthandhabung,
EMI/EMF-Kompatibilität, Zugänglichkeit und verwandte Themen finden Sie
in den Extron-Richtlinien für Sicherheit und Handhabung (Artikelnummer
68-290-01) auf der Extron-Website, www.extron.com.
Instrucciones de seguridad • Español
ADVERTENCIA: Este símbolo,
D
, cuando se utiliza en el producto,
avisa al usuario de la presencia de voltaje peligroso sin aislar dentro del
producto, lo que puede representar un riesgo de descarga eléctrica.
ATENCIÓN: Este símbolo,
I
, cuando se utiliza en el producto,
avisa al usuario de la presencia de importantes instrucciones de uso y
mantenimiento recogidas en la documentación proporcionada con el
equipo.
Para obtener información sobre directrices de seguridad, cumplimiento
de normativas, compatibilidad electromagnética, accesibilidad y temas
relacionados, consulte la Guía de cumplimiento de normativas y seguridad
de Extron, referencia 68-290-01, en el sitio Web de Extron,
www.extron.com.
Instructions de sécurité • Français
AVERTISSEMENT : Ce pictogramme,
D
, lorsqu’il est utilisé sur
le produit, signale à l’utilisateur la présence à l’intérieur du boîtier du
produit d’une tension électrique dangereuse susceptible de provoquer
un choc électrique.
ATTENTION : Ce pictogramme,
I
, lorsqu’il est utilisé sur
le produit, signale à l’utilisateur des instructions d’utilisation ou de
maintenance importantes qui se trouvent dans la documentation
fournie avec le matériel.
Pour en savoir plus sur les règles de sécurité, la conformité à la
réglementation, la compatibilité EMI/EMF, l’accessibilité, et autres sujets
connexes, lisez les informations de sécurité et de conformité Extron,
réf. 68-290-01, sur le site Extron, www.extron.com.
Istruzioni di sicurezza • Italiano
AVVERTENZA: Il simbolo,
D
, se usato sul prodotto, serve ad
avvertire l’utente della presenza di tensione non isolata pericolosa
all’interno del contenitore del prodotto che può costituire un rischio di
scosse elettriche.
ATTENTZIONE: Il simbolo,
I
, se usato sul prodotto, serve ad
avvertire l’utente della presenza di importanti istruzioni di funzionamento
e manutenzione nella documentazione fornita con l’apparecchio.
Per informazioni su parametri di sicurezza, conformità alle normative,
compatibilità EMI/EMF, accessibilità e argomenti simili, fare riferimento
alla Guida alla conformità normativa e di sicurezza di Extron, cod. articolo
68‑290‑01, sul sito web di Extron, www.extron.com.
Instrukcje bezpieczeństwa • Polska
OSTRZEŻENIE: Ten symbol,
D
, gdy używany na produkt, ma na celu
poinformować użytkownika o obecności izolowanego i niebezpiecznego
napięcia wewnątrz obudowy produktu, który może stanowić zagrenie
porażenia prądem elektrycznym.
UWAGI: Ten symbol,
I
, gdy używany na produkt, jest przeznaczony do
ostrzegania użytkownika ważne operacyjne oraz instrukcje konserwacji
(obsługi) w literaturze, wyposażone w sprzęt.
Informacji na temat wytycznych w sprawie bezpieczeństwa, regulacji wzajemnej
zgodności, zgodność EMI/EMF, dostępności i Tematy pokrewne, zobacz Extron
bezpieczeństwa i regulacyjnego zgodności przewodnik, część numer 68-290-01,
na stronie internetowej Extron, www.extron.com.
Инструкция по технике безопасности Русский
ПРЕДУПРЕЖДЕНИЕ: Данный символ,
D
, если указан
на продукте, предупреждает пользователя о наличии
неизолированного опасного напряжения внутри корпуса
продукта, которое может привести к поражению электрическим
током.
ВНИМАНИЕ: Данный символ,
I
, если указан на продукте,
предупреждает пользователя о наличии важных инструкций по
эксплуатации и обслуживанию в руководстве, прилагаемом к
данному оборудованию.
Для получения информации о правилах техники безопасности,
соблюдении нормативных требований, электромагнитной
совместимости (ЭМП/ЭДС), возможности доступа и других вопросах
см. руководство по безопасности и соблюдению нормативных
требований Extron на сайте Extron: www.extron.com, номер по
каталогу - 68-290-01.
安全说明 简体中文
警告D产品上的这个标志意在警告用户产品机壳内暴露的危险 电压
有触电危险
注意I 产品上的这个标志意在提示用户设备随附的用户手册中有
重要的操作和维护(维修说明
关于我们产品的安全指南、遵循的规范、EMI/EMF 的兼容性、无障碍
使用的特性等相关内容,敬请访问 Extron 网站 www.extron.com参见 Extron
安全规范指南,产品编号 68‑290‑01
Safety Instructions
安全記事 繁體中文
警告: D 若產品上使用此符號,是為了提醒使用者產品殼內存在著
可能會導致觸電之風險的未絕緣危險電壓。
注意I 若產品上使用此符號,是為了提醒使用者設備隨附的用戶手冊中有
護( )説
有關安全性指導方法規遵守EMI/EMF 相容性存取範圍和相關主題的詳細
資訊請瀏覽 Extron 網站www.extron.com,然 Extron 安全性與
》,準 68‑290‑01
安全上の注意 日本語
警告: の記号 D 示されて縁されて
いなれ、ること示しいま
注意: この記号 I 製品上に表示されている場合は、の取扱説明書に
記載され いる重要な操作と保守(整備)の指示についーの注意
す。
安全上の注意、法令遵守、EMI/EMF適合性、その他の関連項目
スト イト www.extron.com より
Extron Safety and Regulatory Compliance Guide(P/N 68‑290‑01) をご
くだ
안전 지침 한국어
경고: 이 기호 D, 가 제품에 사용될 경우, 제품의 인클로저 내에 있는
접지되지 않은 위험한 전류로 인해 사용자가 감전될 위험이
있음을 경고합니다.
주의: 이 기호 I, 가 제품에 사용될 경우, 장비와 함께 제공된 책자에
나와 있는 주요 운영 및 유지보수(정비) 지침을 경고합니다.
전 가이드라인, 규제 준수, EMI/EMF 호환성, 접근성, 그리고 관련 항목에
대한 자세한 내용은 Extron 웹 사이트(www.extron.com)의 Extron 안전 및
제 준수 안내서, 68-290-01 조항을 참조하십시오.
Copyright
© 2015 - 2019 Extron Electronics. All rights reserved.
Trademarks
All trademarks mentioned in this guide are the properties of their respective owners.
The following registered trademarks
®
, registered service marks(
SM
), and trademarks(™) are the property of RGBSystems, Inc. or Extron Electronics
(see the current list of trademarks on the Terms of Use page at www.extron.com):
Registered Trademarks
(
®
)
Cable Cubby, ControlScript, CrossPoint, DTP, eBUS, EDID Manager, EDID Minder, Extron, Flat Field, FlexOS, Glitch Free, Global Configurator,
Global Scripter, GlobalViewer, Hideaway, HyperLane, IPIntercom, IPLink, Key Minder, LinkLicense, LockIt, MediaLink, MediaPort,
NetPA, PlenumVault, PoleVault, PowerCage, PURE3, Quantum, Show Me, SoundField, SpeedMount, SpeedSwitch, StudioStation,
SystemINTEGRATOR, TeamWork, TouchLink, V-Lock, VideoLounge, VN-Matrix, VoiceLift, WallVault, WindoWall, XTP, XTP Systems, and ZipClip
Registered Service Mark
(SM)
: S3 Service Support Solutions
Trademarks
(
)
AAP, AFL (Accu-Rate Frame Lock), ADSP (Advanced Digital Sync Processing), Auto-Image, AVEdge, CableCover, CDRS (Class D
Ripple Suppression), Codec Connect, DDSP (Digital Display Sync Processing), DMI (Dynamic Motion Interpolation), DriverConfigurator,
DSPConfigurator, DSVP (Digital Sync Validation Processing), eLink, EQIP, Everlast, FastBite, FOX, FOXBOX, IP Intercom HelpDesk, MAAP,
MicroDigital, Opti-Torque, PendantConnect, ProDSP, QS-FPC (QuickSwitch Front Panel Controller), Room Agent, Scope-Trigger, ShareLink, SIS,
Simple Instruction Set, Skew-Free, SpeedNav, Triple-Action Switching, True4K, Vector™ 4K, WebShare, XTRA, and ZipCaddy
FCC Class A Notice
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part15 of the FCC rules. The ClassA limits provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause interference.
This interference must be corrected at the expense of the user.
NOTES:
This unit was tested with shielded I/O cables on the peripheral devices. Shielded
cables must be used to ensure compliance with FCC emissions limits.
For more information on safety guidelines, regulatory compliances, EMI/EMF
compatibility, accessibility, and related topics, see the Extron Safety and
Regulatory Compliance Guide on the Extron website.
Battery Notice
This product contains a battery. Do not open the unit to replace the battery. If the
battery needs replacing, return the entire unit to Extron (for the correct address, see the Extron
Warranty section on the last page of this guide).
CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose of used
batteries according to the instructions.
ATTENTION : Risque d’explosion. Ne pas remplacer la pile par le mauvais type de pile.
Débarrassez-vous des piles utilisées selon le mode d’emploi.
Conventions Used in this Guide
Notifications
In this user guide, the following are used:
WARNING: Potential risk of severe injury or death.
AVERTISSEMENT : Risque potentiel de blessure grave ou de mort.
CAUTION: Risk of minor personal injury.
ATTENTION : Risque de blessuremineure.
ATTENTION:
Risk of property damage.
Risque de dommages matériels.
NOTE: A note draws attention to important information.
Software Commands
Commands are written in the fonts shown here:
^AR Merge Scene,,Op1 scene 1,1 ^B 51 ^W^C
[01] R 0004 00300 00400 00800 00600 [02] 35 [17] [03]
E
X!
*
X1&
*
X2)
*
X2#
*
X2!
CE
}
NOTE: For commands and examples of computer or device responses mentioned
in this guide, the character “0” is used for the number zero and “O” represents the
capital letter “o”.
Computer responses and directory paths that do not have variables are written in the font shown
here:
Reply from 208.132.180.48: bytes=32 times=2ms TTL=32
C:\Program Files\Extron
Variables are written in slanted form as shown here:
ping xxx.xxx.xxx.xxx —t
SOH R Data STX Command ETB ETX
Selectable items, such as menu names, menu options, buttons, tabs, and field names are written
in the font shown here:
From the File menu, select New.
Click the OK button.
Specifications Availability
Product specifications are available on the Extron website, www.extron.com.
Extron Glossary of Terms
A glossary of terms is available at www.extron.com/technology/glossary.aspx.
Contents
Introduction............................................................ 1
About the TLP Pro 1220, 1520, and 1720 Series ....1
Features .................................................................. 2
Application Diagram ................................................3
Requirements ..........................................................3
Software .............................................................3
Hardware ............................................................3
Installation Overview ........................................... 4
Panel Features ...................................................... 6
TLP Pro 1220, 1520, and 1720 Series
Front Panel Features ..............................................6
TLP Pro 1220, 1520, and 1720 Series
Rear Panel Features ............................................... 8
Routing Cables (TG Models) ..................................12
Setup Menu .......................................................... 13
Setup Menu ..........................................................13
Status Screen ...................................................14
Network Screen ................................................14
Display Screen ..................................................16
Audio Screen ....................................................17
Input Screen .....................................................17
Advanced Screen..............................................19
Configuration Software ..................................... 20
Configuration Software .......................................... 20
Install GUI Designer, Global Configurator,
and Toolbelt .........................................................21
Using the Software ............................................22
TLP Pro 1220, 1520, and 1720 Series
Web Page ............................................................ 22
Updating the Firmware ..........................................23
Downloading Firmware ......................................23
Updating Firmware Using the Touchpanel
Web Page ........................................................ 23
Updating Firmware Using Toolbelt ..................... 23
Mounting ............................................................... 24
Mounting the TLP Pro 1220MG, 1520MG,
and 1720MG .......................................................24
Rack Mounting ..................................................24
Wall Mounting ...................................................25
Mounting the TLP Pro 1220TG, 1520TG,
and 1720TG ........................................................28
Removing the Back and Base Covers ...............28
Desktop Mounting ............................................28
VESA Mounting .................................................29
Reference Material ............................................. 30
Network Port Requirements and Licensed
Third-Party Software Used by the Touchpanels ....30
Reset Modes.........................................................30
Use Factory Firmware .......................................30
Reset All IP Settings .......................................... 31
Reset to Factory Defaults ..................................31
TLP Pro 1220, TLP Pro 1520, and TLP Pro 1720 Series • Contents vii
TLP Pro 1220, TLP Pro 1520, and TLP Pro 1720 Series • Contents viii
Introduction
This guide describes the function, installation, and operation of the following Extron Touchlink Pro
Touchpanels:
TLP Pro 1220MG TLPPro1220TG
TLP Pro 1520MG TLPPro1520TG
TLP Pro 1720MG TLPPro1720TG
Unless otherwise stated, the terms “touchpanel” or “TLP Pro” refer to any of the six models.
The touchpanels are ideal for any AV applications requiring large touchpanels with flexible
mounting options and fully customizable interfaces.
This section provides an overview of these products:
About the TLP Pro 1220, 1520, and 1720 Series
Features
Application Diagram
Requirements
About the TLP Pro 1220, 1520, and 1720 Series
The TLP Pro 1220 Series touchpanels have 12.1 inch screens with a resolution of 1280x800.
The TLP Pro 1520 Series touchpanels have 15.6 inch screens with a resolution of 1366x768.
The TLP Pro 1720 Series touchpanels have 17.3 inch screens with a resolution of 1920x1080.
The MG models (TLP Pro 1220MG, TLP Pro 1520MG, and TLP Pro 1720MG) are
wall-mountable. The TG models (TLP Pro 1220TG, TLP Pro 1520TG, and TLP Pro 1720TG) have
a weighted base that can be tilted, which allows them to stand on any suitable table or desktop.
A range of mounting options are available for all the models (see Mounting on page24).
The screen layout is designed with the Extron GUI Designer software. The functions are assigned
to the screen objects with the Extron Global Configurator Plus and Professional software. This
provides versatility and adaptability to the configuration and control of an AV system.
A motion sensor, a light sensor, and a speaker provide sleep mode, auto dimming, and audible
feedback.
TLP Pro 1220, TLP Pro 1520, and TLP Pro 1720 Series • Introduction 1
Features
Capacitive touchscreen with 16 million colors
12.1 inch screen with 1280x800 resolution (TLPPro1220 series)
15.6 inch screen with 1366x768 resolution (TLPPro1520 series)
17.3 inch screen with 1920x1080 resolution (TLP Pro 1720 series)
Faster processing and more memory — Allows for quicker configuration uploads and
more storage for GUI pages.
Full motion video preview and monitoring — With HDMI and XTP inputs
Compatible with the full range of Extron IPL Pro and IPCP Pro control processors
— Allows easy integration into existing systems
Power over EthernetTouchpanel receives power and communication over a single
Ethernet cable, eliminating the need for a local power supply.
Built-in speakers provide stereo audio — For video preview and audible feedback from
button presses.
3.5 mm headphone jack — Provides local audio out from the touchpanel.
Light sensor — Adjusts screen brightness as the ambient room lighting changes.
Configurable red and green status lights —Indicate the availability or call status of a
room.
System connection status indicator — The communication LED provides visual
feedback if the touchpanel is not communicating with a control processor.
Two high speed USB 2.0 ports — For future expansion
Automatic clock synchronization — Allows touchpanel to display the accurate time and
date.
Energy-saving features
Adjustable sleep timer puts touchpanel into sleep mode
Motion detector wakes touchpanel
Mounting options for tilt models (TG models):
Sit on a tabletop — weighted base allows up to 45° of tilt.
Threaded holes in baseplate allow for secure mounting to a table.
Kensington
®
lock support allows the touchpanels to be locked to a table or other flat
surface.
Supports the optional SMA-1 Swivel Mount Adapter.
VESA FDMI Type D 100 mm mounting pattern standard can be used for VESA
mounting.
Mounting options for wall-mount models (MG models):
Mount on a wall, lectern, or any flat surface.
The optional back box, BB 700M can be used where local codes require a rear metal
enclosure.
Fully customizable using Extron control system software — GUI Designer combined
with Global Configurator Plus and Professional
Supports the Extron Control App.
TLP Pro 1220, TLP Pro 1520, and TLP Pro 1720 Series • Introduction 2
Application Diagram
The application diagram below shows the TLP Pro 1220MG. The other touchpanels described in
this user guide can be used in similar configurations.
POWER
12V
--A MAX
G
Tx Rx RTSCTS
COM 1
G
Tx Rx
COM 2
VCG
VOL
RELAYS
1 2 C
1 2 3 4 G
DIGITAL I/O
PWR OUT = 6W
eBUS
+V +S
-S
G
LAN
IPCP PRO 250
IR/S
S G
POWER
12V
0.4A MAX
RS-232
Tx Rx G
12
INPUT
REMOTE
OUTPUTS
ABCDEF
1
Help
System
Off
Display
Room
Control
Off
Mute
Screen
Lighting
December 15, 2013 - 7:58 AM
Audio
Control
Volume
Mute
Tuner
1 2 3
VCRLaptop PC DVD
Doc
Cam
Tuner
On
Channel
Last
Presets
More
Presets
321
654
987
Enter
0
TCP/IP
Network
Display
Power Sequencer
Media Player
Extron
IPCP Pro 250
IP Link Pro
Control Processor
PC
IRRS-232HDMI HDMI
HDMI
Ethernet
Ethernet
Ethernet/Power
Extron
TLP Pro 1220MG
12" Wall Mount
TouchLink Pro
Touchpanel
Extron
HDMI DA2
Distribution Amplier
Motion
Sensor
Power Injector
Figure 1. Application Diagram
Requirements
Software
For a complete list of the requirements for running GUI Designer, Global Configurator Plus and
Professional, and Toolbelt see the Extron web page for that software.
NOTE: These touchpanels are not compatible with GlobalConfigurator 3 or
GUIConfigurator.
Hardware
An Extron IP Link Pro control interface must also be connected to the same network domain as
the TouchLink panel. See www.extron.com for a list of suitable controllers.
NOTE: These touchpanels are not compatible with Extron IP Link (non-Pro) controllers.
TLP Pro 1220, TLP Pro 1520, and TLP Pro 1720 Series • Introduction 3
Installation
Overview
This section contains an overview of the installation process. Follow the links for a more detailed
explanation of each step.
1. Before starting, download and install the latest versions of the following software:
GUI Designer — For designing layouts for Extron TouchLink Pro touchpanels and third
party touch interfaces.
Global Configurator Plus and Professional — For setting up and configuring the
control processor and touchpanel.
Toolbelt — Provides device discovery, device information, firmware updates,
and configuration of network settings, system utilities, and user management for
TouchLink Pro devices.
See Configuration Software on page 20.
2. Obtain the following network information from your network administrator:
Dynamic Host Configuration Protocol (DHCP) status (on or off). If DHCP is off, you will
also require:
IP address
Subnet mask
Gateway
User name — This can be either admin or user.
Password — By default, this is extron (for either admin or user).
MAC address — Make a note of the touchpanel MAC address, which can be found on
the rear panel label (you need to remove the back cover for TG models).
3. Mount and cable the units:
ATTENTION:
Do not power on the touchpanels or control processors until you have read
the Attention notice on page 11 (12 VDC power supply) or on page 10 (power
injector).
Ne branchez pas les écrans tactiles ou les contrôleurs avant d’avoir lu les mises
en garde page 11 (source d’alimentation 12VCC) ou page 10 (injecteur PoE).
Mount the units. There are several mounting options for TouchLink Pro touchpanels (see
Mounting on page 24).
NOTE: If you use the setup menu to configure the wall-mount models, do not
mount the unit before configuring them as you need access to the rear panel
Menu button.
Connect cables to the touchpanels (see TLP Pro 1220, 1520, and 1720 Series Rear
Panel Features on page 8).
Connect the power cords and power on all devices (see XTP/PoE/LAN input on page
8 or 12V power input on page 10).
TLP Pro 1220, TLP Pro 1520, and TLP Pro 1720 Series • Installation Overview 4
4. Set up the touchpanels for network communication:
Connect the PC that you are using for setup, the control processor, and the touchpanel
to the same Ethernet subnetwork.
Use the Setup Menu (see page 13) or Toolbelt to set the DHCP status and,
if necessary, the IP address, subnet mask, gateway, and related settings for the
touchpanel.
5. Configure the Touchpanels — the GUI Designer Help File, the Global Configurator Help File,
and the Toolbelt Help File provide step-by-step instructions and detailed information.
The Global Configurator Help File also includes an introduction to that software and sections
on how to start a project and configuration.
TLP Pro 1220, TLP Pro 1520, and TLP Pro 1720 Series • Installation Overview 5
Panel Features
This section describes:
TLP Pro 1220, 1520, and 1720 Series Front Panel Features
TLP Pro 1220, 1520, and 1720 Series Rear Panel Features
TLP Pro 1220, 1520, and 1720 Series Front Panel Features
Figure 2 shows the TLP Pro 1720MG and TLP Pro 1720TG front panels. The features of
TLP Pro 1220MG and 1520MG models are very similar to the TLP Pro 1720MG and the features
of TLP Pro 1220TG and 1520TG models are very similar to the TLP Pro 1720TG.
AABBC
CD
D
E
EE
EFF
GG
AAB
BCCDD
E
EF
FE
E
Figure 2. TLP Pro 1720MG (Left) and TLP Pro 1720TG (Right) Front Panels
A
Communication LED
B
Status light
C
Ambient light sensor
D
Capacitive touch screen
E
Speakers (2)
F
Motion sensor
G
Menu button (MG models only)
TLP Pro 1220, TLP Pro 1520, and TLP Pro 1720 Series • Panel Features 6
A
Communication LED (see figure 2 on the previous page) — shows the configuration and
connection status of the touchpanel:
Unlit during normal operation (the touchpanel is configured and connected to an
IP Link Pro control processor).
Blinks red if the touchpanel has been configured but is not connected to an IP Link Pro
control processor.
Permanently lit if the touchpanel has not been configured.
The indicator can be toggled between enabled and disabled, using the Setup Menu (see
page 13).
B
Status light — one LED light bar, above the screen, which can be programmed to provide
system feedback.
Light red or green
Blink or light continuously
For information about programming this light, see the Global Configurator Help File.
C
Ambient light sensor — monitors ambient light level and adjusts screen brightness, based
on the settings configured using the Setup Menu.
D
Capacitive touch screen — with a touch overlay. The touchpanel has a resolution
of 1280x800 (TLP Pro 1220 series), 1366x768 (TLP Pro 1520 series), or 1920x1080
(TLP Pro 1720 series).
E
Speakers — two speakers located below the screen, one on each side of the panel,
provide stereo audio for video preview and audible feedback from button presses.
F
Motion sensor — detects motion between three to five feet from the touchpanel, and at
least 15° from the center axis.
When no motion has been detected for a user-defined period of time, the touchpanel
enters sleep mode.
When motion is detected by the sensor, the screen display is restored and active.
G
Menu Button (MG models only) — activates the setup menu and calibration screen (Setup
Menu). It is accessed from under the touchpanel.
TLP Pro 1220, TLP Pro 1520, and TLP Pro 1720 Series • Panel Features 7
TLP Pro 1220, 1520, and 1720 Series Rear Panel Features
Figure 3 shows the TLP Pro 1720MG and TLP Pro 1720TG rear panels. The TLP Pro 1720TG is
shown with the rear cover removed. The features of TLP Pro 1220MG and 1520MG models are
very similar to the TLP Pro 1720MG and the features of TLP Pro 1220TG and 1520TG models
are very similar to the TLP Pro 1720TG.
AA
B
B
C
C
D
D
EEFFGG
II
JJ
HH
BBF
FEEDDAA
CC
II
H
H
G
G
J
J
KK
DDEEFFGGH
H
KK
AA
B
B
C
C
L
L
MM
Figure 3. TLP Pro 1720MG (Left) and TLP Pro 1720TG (Right) Rear Panels
A
Reset LED
H
12V power input (see page 10)
B
Reset button
I
Mounting notches (see page 12) (MG models only)
C
Menu button
J
Mounting screws (see page 12) (MG models only)
D
USB connectors (2)
K
Rear status light (see page 12) (TG models only)
E
Audio output
L
VESA mounting holes (see page 12) (TG models only)
F
XTP/PoE/LAN input
M
Base attachment hinges (see page 12) (TG models only)
G
HDMI input (see page 10)
A
Reset LED— indicates power status and reset status of the device (see Reset Modes on
page 30).
B
Reset button— initiates one of three reset modes for the unit (see Reset Modes).
C
Menu button— activates the Setup Menu (see page 13).
D
USB connectors — two high speed USB 2.0 connectors for peripheral controls.
E
Audio output — a 3.5 mm headphone jack provides local line level audio output from the
touchpanel.
F
XTP/PoE/LAN input — accepts an input from a LAN or an Extron XTP transmitter. Use
Cat 5e or greater cable terminated with an RJ-45 connector. Extron recommends using
XTP DTP 24 SF/UTP cable for the best performance. At a minimum, Extron recommends
24 AWG, solid conductor, STP cable with a minimum bandwidth of 400 MHz.
An Extron IPL Pro Control Processor must also be connected to the same network domain
as the TouchLink Pro touchpanel. See www.extron.com for a list of suggested models.
The network port has two LEDs. The green LED lights steadily to indicate that the
touchpanel is connected correctly to a network. The yellow LED flashes to indicate that data
is being passed to or from the touchpanel.
TLP Pro 1220, TLP Pro 1520, and TLP Pro 1720 Series • Panel Features 8
These touchpanels can use either a 12 VDC desktop power supply or a Power over Ethernet
power injector.
The Extron PI 140 power injector is provided with the TLP Pro 1720 series touchpanels. Do
not use a different power injector with these models.
ATTENTION:
Do not connect either power supply before reading the Attention notifications on
page 10 or page 11.
Ne branchez pas de sources d’alimentation externes avant d’avoir lu les mises
en garde dans la section «PowerSupply» sur page 10 ou page 11.
If you are using a 12V power input (see page 10), connect the touchpanel directly to an
XTP source or to a LAN.
To use a PoE power injector, connect the touchpanel as shown in figure 4, below. You
must use the PI 140 (shown in figure 4) with the TLP Pro 1720 series touchpanels and
Extron recommends using this power injector with the TLP Pro 1220 and TLP Pro 1520
series touchpanels.
Limit the use to no more than two pass-through points, which may include patch points,
punch down connectors, couplers and power injectors. If these pass-through points are
required, use shielded couplers and punch-down connectors
NOTES: When using shielded twisted pair cable in bundles or conduits, consider
the following:
Do not exceed 40% fill capacity in conduits.
Do not comb the cable for the first 20 meters, where cables are straightened,
aligned, and secured in tight bundles.
Loosely place cables and limit the use of tie wraps or hook-and-loop
fasteners.
Keep twisted pair cables separate from AC power cables.
To use a PoE power injector — connect an Ethernet
cable to the power supply and a switch or router. This
cable carries network information from the switch
or router to the power supply input. A second cable
carries the network information and 56VDC from the
power supply to the touchpanel. Connect the IEC
power cord to a convenient 100 VAC to 240 VAC,
50-60 Hz power source.
Figure 4. Connecting the Power Injector
100-240V~50/60 Hz
1.1A MAX
INPUT OUTPUT
POWERED TLP
LAN
To Network or
XTP Device
To a TLP Pro
touchpanel
Extr
on PI 140
TLP Pro 1220, TLP Pro 1520, and TLP Pro 1720 Series • Panel Features 9
ATTENTION:
Always use a power supply provided by or specified by Extron. Use of an
unauthorized power supply voids all regulatory compliance certification and may
cause damage to the supply and the end product.
Utilisez toujours une source d’alimentation fournie ou recommandée par Extron.
L’utilisation d’une source d’alimentation non autorisée annule toute conformité
réglementaire et peut endommager la source d’alimentation ainsi que le produit
final.
The installation must always be in accordance with the applicable provisions of
National Electrical Code ANSI/NFPA 70, article 725 and the Canadian Electrical
Code part 1, section 16.
Cette installation doit toujours être en accord avec les mesures qui s’applique
au National Electrical Code ANSI/NFPA70, article725, et au Canadian Electrical
Code, partie1, section16.
These products are intended for use with a UL Listed power source marked
“Class 2” or “LPS” and rated 12VDC, minimum 3.0 A. or 56 VDC (PoE), minimum
0.8 A.
Ces produits sont destiné à une utilisation avec une source d’alimentation
listéeUL avec l’appellation «Classe2» ou «LPS» et normée 12Vcc, 3,0A
minimum ou 56Vcc (PoE), 0,8A minimum.
The power supply shall not be permanently fixed to the building structure or
similar structure.
La source d’alimentation ne devra pas être fixée de façon permanente à une
structure de bâtiment ou à une structure similaire.
Power over Ethernet (PoE) is intended for indoor use only. It is to be connected
only to networks or circuits that are not routed to the outside plant or building.
L’alimentation via Ethernet (PoE) est destinée à une utilisation en intérieur
uniquement. Elle doit être connectée seulement à des réseaux ou des circuits qui
ne sont pas routés au réseau ou au bâtiment extérieur.
The touchpanels are intended for connection to a Power over Ethernet circuit for
intra-building use only and are considered to be part of a Network Environment 0
per IEC TR62101.
Les écrans tactiles sont conçu pour une connexion à un circuit PoE pour une
utilisation intérieure seulement et est considéré comme faisant partie d’un
environnement réseau 0 par IECTR62101.
G
HDMI input (see figure 3 on page 8) — One female HDMI connector for video input.
H
12V Power input — power supplies must be purchased separately.
Connect a 12 VDC, 3.0 A power supply to the rear panel power receptacle. Extron
recommends using the PS 1230 power supply
WARNING: The two power cord wires must be kept separate while the power
supply is plugged in. Remove power before wiring.
AVERTISSEMENT : Les deux cordons d’alimentation doivent être tenus à l’écart
l’un de l’autre quand l’alimentation est branchée. Couper l’alimentation avant de
faire l’installation électrique.
NOTES:
The TLP Pro 1220 and 1520 series touchpanels ship without a power supply.
Either the 12 VDC power supply or the power injector must be purchased
separately.
Power supplies for the TG models use DC plugs. Power supplies for the MG
models use captive screw connectors.
TLP Pro 1220, TLP Pro 1520, and TLP Pro 1720 Series • Panel Features 10
ATTENTION:
Always use a power supply provided by or specified by Extron. Use of an
unauthorized power supply voids all regulatory compliance certification and may
cause damage to the supply and the end product.
Utilisez toujours une source d’alimentation fournie ou recommandée par Extron.
L’utilisation d’une source d’alimentation non autorisée annule toute conformité
réglementaire et peut endommager la source d’alimentation ainsi que le produit final.
The installation must always be in accordance with the applicable provisions of
National Electrical Code ANSI/NFPA 70, article 725 and the Canadian Electrical Code
part 1, section 16.
Cette installation doit toujours être en accord avec les mesures qui s’applique au
National Electrical Code ANSI/NFPA70, article725, et au Canadian Electrical Code,
partie1, section16.
These products are intended for use with a UL Listed power source marked “Class 2”
or “LPS” and rated 12VDC, minimum 3.0 A. or 56 VDC (PoE), minimum 0.8 A.
Ces produits sont destiné à une utilisation avec une source d’alimentation listéeUL
avec l’appellation «Classe2» ou «LPS» et normée 12Vcc, 3,0A minimum ou
56Vcc (PoE), 0,8A minimum.
The power supply shall not be permanently fixed to the building structure or similar
structure.
La source d’alimentation ne devra pas être fixée de façon permanente à une structure
de bâtiment ou à une structure similaire.
Unless otherwise stated, the AC/DC adapters are not suitable for use in air handling
spaces or in wall cavities. The power supply is to be located within the same vicinity
as the Extron AV processing equipment in an ordinary location, Pollution Degree 2,
secured to the equipment rack within the dedicated closet, podium, or desk.
Sauf mention contraire, les adaptateurs AC/DC ne sont pas appropriés pour une
utilisation dans les espaces d’aération ou dans les cavités murales. La source
d’alimentation doit être située à proximité de l’équipement de traitement audiovisuel
dans un endroit ordinaire, avec un degré2 de pollution, fixé à un équipement de rack
à l’intérieur d’un placard, d’une estrade, ou d’un bureau.
Extron power supplies are certified to UL/CSA 60950-1 and are classified as LPS
(Limited Power Source). Use of a non-LPS or unlisted power supply will void all
regulatory compliance certification.
Les sources d’alimentation Extron sont qualifiées UL/CSA60950-1 et sont
classéesLPS(LimitedPowerSource). L’utilisation d’une source d’alimentation non-
listée ou non-listéeLPS annulera toute certification de conformité réglementaire.
The length of the exposed wires in the stripping process is critical. The ideal length is
3/16 inches (5 mm). If they are any longer, the exposed wires may touch, causing a
short circuit between them. If they are any shorter, the wires can be easily pulled out
even if tightly fastened by the captive screws.
La longueur des câbles exposés est primordiale lorsque l’on entreprend de les
dénuder. La longueur idéale est de 5mm (3/16inches). S’ils sont un peu plus longs,
les câbles exposés pourraient se toucher et provoquer un court circuit. S’ils sont un
peu plus courts, ils pourraient sortir, même s’ils sont attachés par les vis captives.
Do not tin the wire leads before installing into the connector. Tinned wires are not as
secure in the connector and could be pulled out.
Ne pas étamer les conducteurs avant de les insérer dans le connecteur. Les câbles
étamés ne sont pas aussi bien fixés dans le connecteur et pourraient être retirés.
TLP Pro 1220, TLP Pro 1520, and TLP Pro 1720 Series • Panel Features 11
I
Mounting notches (2) (MG models only) (see figure 3 on page 8) — lower these
notches over the hooks at the top of the mounting frame (see Wall Mounting on page
25).
J
Mounting screws (2) (MG models only) — for securing the bottom of the touchpanel to the
mounting frame (see Wall Mounting).
K
Rear status light (TG models only) — one LED light bar that can be programmed to
provide system feedback.
Light red or green
Blink or light continuously
TG models have a status light on both the front and rear panels. Both lights provide
the same information and cannot be programmed individually. For information about
programming this light, see the Global Configurator Help File.
L
VESA mounting holes (4) — VESA FDMI Type D 100 mm mounting pattern standard used
for VESA mounting (see VESA Mounting on page 29).
M
Base attachment hinges (2) (TG models only) — Secure the base to the touchpanel. For
VESA Mounting, remove the base by unscrewing the hinges.
Routing Cables (TG Models)
Organize cables behind the rear and base covers for a more esthetically appealing appearance.
The TLP Pro 1520TG is shown below but the TLP Pro 1220TG and TLP Pro 1720TG are similar.
AA
B
B
C
C
C
C
D
D
Figure 5. TLP Pro 1520TG Cable Organization
1. If necessary, remove the rear and base covers and connect the cables as required.
2. Run the cables through the clamp on the back (
A
), and through the restricted gap where
the base and back meet (
B
).
3. Run the cables through the raceways on either side of the center hole (
C
), and through the
clamp at the back of the base (
D
). Multiple cables, can be loosely bundled to keep them
organized.
4. Move the cable clamp back into position and press the top to secure it in place
5. Put back the rear and base covers. The base cover must be inserted before the rear cover.
TLP Pro 1220, TLP Pro 1520, and TLP Pro 1720 Series • Panel Features 12
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40

Extron TLP Pro 1520TG Manuel utilisateur

Taper
Manuel utilisateur

dans d''autres langues