VTech CS5119 Manuel utilisateur

Marque: VTech

Modèle: CS5119

Catégorie: Téléphones

Taper: Manuel utilisateur

Ce manuel convient également à

User’s manual

CS5119

CS5119-15

CS5119-16

CS5119-2

DECT 6.0 cordless telephone

Go to www.vtechphones.com (US)

to register your product for

enhanced warranty support and

the latest VTech product news.

Go to phones.vtechcanada.com

(Canada) for the latest VTech

product news.

Scan the QR code for

support information

(US) (CA)

Congratulations

on purchasing your new VTech product.

Before using this telephone, please read

Important safety instructions.

This manual has all the feature operations

and troubleshooting necessary to install

and operate your new VTech telephone.

Please review this manual thoroughly to

ensure proper installation and operation

of this innovative and feature rich VTech

product.

For support, shopping, and everything

new at VTech, visit our website at

www.vtechphones.com.

In Canada, please visit

phones.vtechcanada.com.

Telephones identiﬁed with

this logo have reduced

noise and interference

when used with most T-coil

equipped hearing aids

and cochlear implants.

The TIA-1083 Compliant

Logo is a trademark of the

Telecommunications Industry

Association. Used under

license.

The ENERGY STAR® program

(www.energystar.gov)

recognizes and encourages

the use of products that save

energy and help protect

our environment. We are

proud to mark this product

with the ENERGY STAR® label

indicating it meets the latest

energy efﬁciency guidelines.

Important safety instructions

When using your telephone equipment,

basic safety precautions should always be

followed to reduce the risk of ﬁre, electric

shock and injury, including the following:

1. Read and understand all instructions.

2. Follow all warnings and instructions

marked on the product.

3. Unplug this product from the wall outlet

before cleaning. Do not use liquid or

aerosol cleaners. Use a damp cloth for

cleaning.

4. CAUTION: Do not install the telephone

base at a height above 2 meters.

5. Do not use this product near water such

as near a bath tub, wash bowl, kitchen

sink, laundry tub or swimming pool, or

in a wet basement or shower.

6. Do not place this product on an

unstable table, shelf, stand or other

unstable surfaces.

7. Avoid placing the telephone system in

places with extreme temperature, direct

sunlight, or other electrical devices.

Protect your phone from moisture, dust,

corrosive liquids and fumes.

8. Slots and openings in the back or bottom

of the telephone base and handset are

provided for ventilation. To protect them

from overheating, these openings must

not be blocked by placing the product

on a soft surface such as a bed, sofa or

rug. This product should never be placed

near or over a radiator or heat register.

This product should not be placed in

any area where proper ventilation is not

provided.

9. This product should be operated only

from the type of power source indicated

on the marking label. If you are not sure

of the type of power supply in your

home or ofﬁce, consult your dealer or

local power company.

10. Do not allow anything to rest on the

power cord. Do not install this product

where the cord may be walked on.

Compatible with

Hearing Aid T-Coil

TIA-1083

11. Never push objects of any kind into

this product through the slots in the

telephone base or handset because

they may touch dangerous voltage

points or create a short circuit. Never

spill liquid of any kind on the product.

12. To reduce the risk of electric shock,

do not disassemble this product, but

take it to an authorized service facility.

Opening or removing parts of the

telephone base or handset other than

speciﬁed access doors may expose

you to dangerous voltages or other

risks. Incorrect reassembling can cause

electric shock when the product is

subsequently used.

13. Do not overload wall outlets and

extension cords.

14. Unplug this product from the wall

outlet and refer servicing to an

authorized service facility under the

following conditions:

• When the power supply cord or

plug is damaged or frayed.

• If liquid has been spilled onto the

product.

• If the product has been exposed to

rain or water.

• If the product does not operate

normally by following the operating

instructions. Adjust only those

controls that are covered by the

operation instructions. Improper

adjustment of other controls may

result in damage and often requires

extensive work by an authorized

technician to restore the product to

normal operation.

• If the product has been dropped

and the telephone base and/or

handset has been damaged.

• If the product exhibits a distinct

change in performance.

15. Avoid using a telephone (other than

cordless) during an electrical storm.

There is a remote risk of electric shock

from lightning.

16. Do not use the telephone to report

a gas leak in the vicinity of the leak.

Under certain circumstances, a spark

may be created when the adapter is

plugged into the power outlet, or when

the handset is replaced in its cradle.

This is a common event associated with

the closing of any electrical circuit. The

user should not plug the phone into

a power outlet, and should not put a

charged handset into the cradle, if the

phone is located in an environment

containing concentrations of ﬂammable

or ﬂame-supporting gases, unless there

is adequate ventilation. A spark in such

an environment could create a ﬁre or

explosion. Such environments might

include: medical use of oxygen without

adequate ventilation; industrial gases

(cleaning solvents; gasoline vapors; etc.);

a leak of natural gas; etc.

17. Only put the handset of your telephone

next to your ear when it is in normal talk

mode.

18. The power adapters are intended to be

correctly oriented in a vertical or ﬂoor

mount position. The prongs are not

designed to hold the plug in place if it is

plugged into a ceiling, under-the-table or

cabinet outlet.

19. For pluggable equipment, the socket

outlet shall be installed near the

equipment and shall be easily accessible.

20. CAUTION: Use only the

batteries indicated in this manual. There

may be a risk of explosion if a wrong

type of battery is used for the handset.

Use only the supplied rechargeable

batteries or replacement batteries

(BT262342) for the handset. Do not

dispose of batteries in a ﬁre. They may

explode. Disposed of used batteries

according to the instruction.

• Do not use the battery in following

conditions:

• High or low extreme temperature

during use, storage or

transportation.

• Replacement of a battery with an

incorrect type that can defeat a

safeguard.

• Disposal of a battery into ﬁre

or a hot oven, or mechanically

crushing or cutting of a battery,

that can result in an explosion.

• Leaving a battery in an extremely

high temperature surrounding

environment that can result in

an explosion or the leakage of

ﬂammable liquid or gas.

• A battery subjected to extremely

low air pressure that can result in

an explosion or the leakage of

ﬂammable liquid or gas.

21. Use only the adapter included with

this product. Incorrect adapter polarity

or voltage can seriously damage the

product.

22. The applied nameplate is located at the

bottom or near of the product.

SAVE THESE INSTRUCTIONS

Battery

• Use only the battery provided or

equivalent. To order a replacement, visit

our website at

www.vtechphones.com or call

1 (800) 595-9511. In Canada, go to

phones.vtechcanada.com or call

1 (800) 267-7377.

• Do not dispose of the battery in a ﬁre.

Check with local waste management

codes for special disposal instructions.

• Do not open or mutilate the battery.

Released electrolyte is corrosive and

may cause burns or injury to the eyes

or skin. The electrolyte may be toxic if

swallowed.

• Exercise care in handling batteries in

order not to create a short circuit with

conductive materials.

• Charge the battery provided with this

product only in accordance with the

instructions and limitations speciﬁed in

this manual.

Precautions for users of implanted

cardiac pacemakers

Cardiac pacemakers (applies only to digital

cordless telephones):

Wireless Technology Research, LLC

(WTR), an independent research entity,

led a multidisciplinary evaluation of the

interference between portable wireless

telephones and implanted cardiac

pacemakers. Supported by the U.S.

Food and Drug Administration, WTR

recommends to physicians that:

Pacemaker patients

• Should keep wireless telephones at least

six inches from the pacemaker.

• Should NOT place wireless telephones

directly over the pacemaker, such as in a

breast pocket, when it is turned ON.

• Should use the wireless telephone at the

ear opposite the pacemaker.

WTR’s evaluation did not identify any risk

to bystanders with pacemakers from other

persons using wireless telephones.

About cordless telephones

• Privacy: The same features that make a

cordless telephone convenient create

some limitations. Telephone calls are

transmitted between the telephone

base and the cordless handset by radio

waves, so there is a possibility that

the cordless telephone conversations

could be intercepted by radio receiving

equipment within range of the

cordless handset. For this reason, you

should not think of cordless telephone

conversations as being as private as

those on corded telephones.

• Electrical power: The telephone base

of this cordless telephone must be

connected to a working electrical outlet.

The electrical outlet should not be

controlled by a wall switch. Calls cannot

be made from the cordless handset

if the telephone base is unplugged,

switched off or if the electrical power is

interrupted.

• Potential TV interference: Some

cordless telephones operate at

frequencies that may cause interference

to televisions and VCRs. To minimize or

prevent such interference, do not place

the telephone base of the cordless

telephone near or on top of a TV or VCR.

If interference is experienced, moving

the cordless telephone farther away

from the TV or VCR often reduces or

eliminates the interference.

• Rechargeable batteries: Exercise care in

handling batteries in order not to create

a short circuit with conducting material

such as rings, bracelets and keys. The

battery or conductor may overheat and

cause harm. Observe proper polarity

between the battery and the battery

charger.

• Nickel-metal hydride rechargeable

batteries: Dispose of these batteries in

a safe manner. Do not burn or puncture

the battery. Like other batteries of this

type, if burned or punctured, they could

release caustic material which could

cause injury.

Table of contents

What’s in the box ............................................ 1

Overview ........................................................ 2

Telephone base overview ...................................2

Handset overview ................................................. 2

Charger overview .................................................3

Display icons overview........................................ 4

Telephone base lights overview ....................... 4

Handset lights overview ..................................... 4

Connect ...........................................................4

Connect the telephone base ............................. 4

Connect the charger .............................................5

Mount the telephone base .................................5

Install the battery ...................................................5

Check the battery level ....................................... 6

Charge the battery ............................................... 6

Before use ....................................................... 7

Set date and time .................................................. 7

Check for dial tone................................................7

Operating range ...................................................7

Conﬁgure your telephone .............................. 8

Use the handset menu ........................................ 8

Set language ......................................................... 8

Set date and time ................................................. 8

Dial mode .............................................................. 8

Temporary tone dialing ...................................... 8

Telephone operations .....................................9

Make a call ............................................................. 9

Predial a call .......................................................... 9

Answer a call ......................................................... 9

End a call ................................................................ 9

Speakerphone ...................................................... 9

Volume ................................................................... 9

Mute ..................................................................... 10

Join a call in progress (for multiple handset

models only) .................................................. 10

Call waiting .......................................................... 10

Chain dialing ....................................................... 10

Find handset ........................................................11

Redial list ....................................................... 11

Review a redial list entry ....................................11

Dial a redial list entry...........................................11

Delete a redial list entry .....................................11

Multiple handset use .................................... 12

Intercom ...............................................................12

Answer an incoming call during an

intercom call ...................................................12

Transfer a call ........................................................12

Phonebook ................................................... 13

Add a phonebook entry .................................... 13

Review a phonebook entry .............................. 14

Alphabetical search ........................................... 14

Delete the phonebook entries ........................ 14

Edit a phonebook entry .....................................15

Dial a phonebook entry .....................................15

Caller ID ......................................................... 15

Review a caller ID log entry.............................. 16

Memory match ................................................... 16

Missed call indicator .......................................... 16

View dialing options.......................................... 16

Dial a caller ID log entry ..................................... 17

Save a caller ID log entry to the

phonebook .....................................................17

Delete the caller ID log entries ......................... 17

Call block ....................................................... 18

Block unknown calls .......................................... 18

Add a call block list entry .................................. 18

Review call block list .......................................... 18

Edit a call block list entry ................................... 19

Save a caller ID log entry to the

call block list ................................................... 19

Delete a call block list entry .............................. 19

Mute ﬁrst ring ..................................................... 19

Sound settings ..............................................20

Key tone ............................................................... 20

Ringer tone ......................................................... 20

Ringer volume .................................................... 20

Temporary ringer silencing .............................. 20

Quiet mode.........................................................20

ii 1

What’s in the box

Your telephone package contains the

following items. Save your sales receipt

and original packaging in the event

warranty service is necessary.

NOTE

To purchase replacement batteries or power

adapters, visit our website at

www.vtechphones.com or call

1 (800) 595-9511. In Canada, go to

phones.vtechcanada.com or dial

1 (800) 267-7377.

1 set for CS5119/CS5119-15/

CS5119-16

2 sets for CS5119-2

1 set for CS5119/CS5119-15/

CS5119-16/CS5119-2

1 set for CS5119/CS5119-15/

CS5119-16/CS5119-2

1 set for CS5119-2

Abridged

user’s

manual

Retrieve voicemail from telephone

service ...................................................... 21

Retrieve voicemail ...............................................21

Set your voicemail number ................................21

Turn off the new voicemail indicators ..............21

Screen messages ........................................... 22

ECO mode ..................................................... 23

General product care .................................... 24

Frequently asked questions .......................... 24

The RBRC seal .................................................27

FCC, ACTA and IC regulations ........................27

California Energy Commission battery

charging testing instructions ................... 29

For C-UL compliance only ............................. 30

Limited warranty ........................................... 33

Disclaimer and Limitation of Liability ........... 35

Technical speciﬁcations ................................ 35

2 3

Overview

Telephone base overview

1 –

• Page all system handsets.

2 – light

• Flashes when there is an incoming

call, or another telephone sharing

the same line is in use.

• On when the telephone is in use.

3 – Charging pole

Handset overview

1 – Handset earpiece

2 – LCD display

11 –

• Enter space character during text

editing.

12 –

• Press repeatedly to add or remove

1 in front of the caller ID log entry

before dialing or saving it to the

phonebook.

• Press and hold to set or dial your

voicemail number.

13 –

• Make or answer a call.

• Answer an incoming call when you

receive a call waiting alert.

14 –

• Review the redial list.

• Insert a dialing pause while dialing

or entering numbers into the

phonebook.

15 –

• Review the phonebook when the

telephone is not in use.

• Scroll up while in a menu, or in the

phonebook, caller ID log, call block

list or redial list.

• Move the cursor to the right when

entering numbers or names.

• Increase the listening volume during

a call.

• Review the caller ID log when the

telephone is not in use.

• Scroll down while in a menu, or in

the phonebook, caller ID log, call

block list or redial list.

• Move the cursor to the left when

entering numbers or names.

• Decrease the listening volume

during a call.

16 – light

• On when the handset is charging in

the telephone base or charger.

Charger overview

1 – Charging pole

3 –

• Show the menu.

• While in a menu, press to select an

item, or save an entry or setting.

4 –

• Hang up a call.

• Return to the previous menu or idle

mode without making changes.

• Delete digits while predialing.

• Silence the handset ringer

temporarily while the phone is

ringing.

• Press and hold to erase the missed

call indicator while the handset is

not in use.

5 –

• Press and hold to turn on or off the

quiet mode.

• Show other dialing options when

reviewing a caller ID log entry.

6 –

• Start an intercom conversation or

transfer a call (for multi-handset

models only).

7 – Microphone

8 –

• Mute the microphone during a call.

• Silence the handset ringer

temporarily while the phone is

ringing.

• Delete the displayed entry while

reviewing the phonebook, caller ID

log, call block list or redial list.

• Delete digits or characters when

entering numbers or names.

9 –

• Make or answer a call using the

handset speakerphone.

• Switch between the handset

speakerphone and the handset

earpiece during a call.

10 –

• Switch to tone dialing temporarily

during a call.

4 5

Connect

You can choose to connect the telephone

base for desktop usage or wall mounting.

NOTE

• Use only the adapters provided.

• Make sure the electrical outlets are not

controlled by wall switches.

• The adapters are intended to be correctly

oriented in a vertical or ﬂoor mount position.

The prongs are not designed to hold the

plug in place if it is plugged into a ceiling,

under-the-table or cabinet outlet.

TIP

• If you subscribe to digital subscriber line

(DSL) high-speed Internet service through

your telephone line, make sure you install

a DSL ﬁlter (not included) between the

telephone line cord and telephone wall jack.

Contact your DSL service provider for more

information.

Connect the telephone base

Connect the charger

Display icons overview

The battery icon ﬂashes when

the battery is low and needs

charging.

The battery icon animates

when the battery is charging.

The battery icon becomes

solid when the battery is fully

charged.

The handset ringer is turned

off.

There are new voicemail

received from your telephone

service provider.

NEW New caller ID log entry.

ECO The ECO mode activates

automatically to reduce power

consumption whenever the

handset is synchronized with

the telephone base.

Telephone base lights overview

• On when the telephone line

is in use.

• On when you are registering

a handset.

• Flashes quickly when there is

an incoming call.

• Flashes when another

telephone sharing the same

line is in use.

• Flashes when you are

deregistering all handsets.

Handset lights overview

On when the handset

speakerphone is in use.

On when the handset is

charging in the telephone

base or charger.

Mount the telephone base

Install the battery

Install the battery as shown below.

NOTES

• Use only supplied battery.

• Charge the battery provided with this

product only in accordance with the

instructions and limitations speciﬁed in this

manual.

• If the handset will not be used for a long

time, disconnect and remove the battery to

prevent possible leakage.

THIS SIDE UP

6 7

Check the battery level

After you have installed the battery, check

the battery level on the handset screen.

• If the battery icon is , or , then go

to Before use section to set the date and

time.

• If the screen is blank, or ﬂashes, then

the battery needs to be charged. Go to

Charge the battery section before you

do any setting or operation.

Charge the battery

Place the handset in the telephone base or

the charger to charge.

Once you have installed the battery, the

handset LCD display indicates the battery

status (see the table on the next page).

NOTES

• Press CANCEL or place the handset in the

charger will bypass the set date and time.

• For best performance, keep the handset in

the telephone base or charger when not in

use.

• The battery is fully charged after 12 hours of

continuous charging.

• If you place the handset in the telephone

base or the charger without plugging in the

battery, the screen displays No battery.

Battery

indicators Battery

status Action

The screen

is blank, or

displays Put in

charger and

ﬂashes.

The battery

has no or

very little

charge. The

handset

cannot be

used.

Charge

without

interruption

(at least 30

minutes).

The screen

displays

Low battery

and ﬂashes.

The battery

has enough

charge to be

used for a

short time.

Charge

without

interruption

(about 30

minutes).

The screen

displays

HANDSET X.

The battery

is charged. To keep

the battery

charged,

place it in the

telephone

base or

charger when

not in use.

When the battery is fully charged, you can

expect the following performance:

Operation Operating

time

While in use (talking*) Seven hours

While in speakerphone

mode (talking*) Three and a

half hours

While not in use (standby**) Five days

* Operating times vary depending on your

actual use and the age of the battery.

** Handset is not charging nor in use.

To manually set the date and time, refer to

Conﬁgure your telephone section.

Before use

After you install your telephone or power

returns following a power outage, the

handset will prompt you to set the date

and time.

Set date and time

1. Use the dialing keys (0-9) to enter the

month (MM), date (DD) and year (YY).

Then press SELECT.

2. Use the dialing keys (0-9) to enter the

hour (HH) and minute (MM). Then

press q or p to choose AM or PM.

3. Press SELECT to save.

Check for dial tone

Press . If you hear a dial tone, the

installation is successful.

If you do not hear a dial tone:

• Make sure the installation procedures

described above are properly done.

• It may be a wiring problem. If you have

changed your telephone service to

digital service from a cable company or

a VoIP service provider, the telephone

line may need to be rewired to allow

all existing telephone jacks to work.

Contact your cable/VoIP service

provider for more information.

Operating range

This cordless telephone operates with the

maximum power allowed by the Federal

Communications Commission (FCC). Even

so, this handset and telephone base can

communicate over only a certain distance

- which can vary with the locations of the

telephone base and handset, the weather,

and the layout of your home or ofﬁce.

When the handset is out of range, the

handset displays Out of range or no pwr

at base.

If there is a call while the handset is out of

range, it may not ring, or if it does ring, the

call may not connect well when you press

. Move closer to the telephone base,

then press to answer the call.

If the handset moves out of range during

a telephone conversation, there may be

interference. To improve reception, move

closer to the telephone base.

8 9

Conﬁgure your telephone

Use the handset menu

1. Press MENU when the phone is not in

use.

2. Press q or p until the screen displays

the desired feature menu.

3. Press SELECT.

• To return to the previous menu, press

CANCEL.

• To exit menu display, press and hold

CANCEL.

Set language

The LCD language is preset to English. You

can select English, French or Spanish to be

used in all screen displays.

1. Press MENU when the handset is not

in use.

2. Press q or p to choose Settings and

then press SELECT twice.

3. Press q or p to choose English,

Français or Español.

4. Press SELECT to save your setting. You

hear a conﬁrmation tone.

NOTE

• If you accidentally set the LCD language to

Spanish or French, press MENU and then

enter *364# to change the handset LCD

language back to English while the handset

is not in use.

Set date and time

1. Press MENU on the handset when not

in use.

2. Press q or p to choose Set

date/time and then press SELECT.

3. Use the dialing keys (0-9) to enter the

month (MM), date (DD) and year (YY).

Then press SELECT.

4. Use the dialing keys (0-9) to enter the

hour (HH) and minute (MM). Then

press q or p to choose AM or PM.

5. Press SELECT to save your setting. Your

hear a conﬁrmation tone.

Dial mode

The dial mode is preset to touch-tone

dialing. If you have pulse (rotary) service,

you need to change the dial mode to

pulse dialing before using the telephone.

1. Press MENU when the handset is not

in use.

2. Press q or p to choose Settings, and

then press SELECT.

3. Press q or p to choose Dial mode,

then press SELECT.

4. Press q or p to choose

Touch-tone or Pulse, then press

SELECT to conﬁrm your selection. You

hear a conﬁrmation tone.

Temporary tone dialing

If you have pulse (rotary) service only,

you can switch from pulse to touch-tone

dialing temporarily during a call. This is

useful if you need to send touch-tone

signals to access your telephone banking

or long distance services.

1. During a call, press TONE .

2. Use the dialing keys to enter the

number. The telephone sends touch-

tone signals. It automatically returns to

pulse dialing mode after you end the

call.

Telephone operations Make a call

• Press or , and then dial the

telephone number.

NOTES

• The screen shows the elapsed time as you

talk (in hours, minutes and seconds).

• While entering numbers, press and hold

PAUSE to insert a dialing pause (a P appears).

Predial a call

• Enter the telephone number using the

dialing keys (0-9), then press or to

dial.

NOTE

• When predialing (preview numbers

before dialing), press DELETE or CANCEL

to backspace and delete; press and hold

PAUSE to insert a dialing pause (a P appears).

Answer a call

• Press , or any of the dialing key.

End a call

• Press OFF or put the handset back in the

telephone base or charger.

Speakerphone

During a call, press to switch between

speakerphone and normal handset use.

When the speakerphone is active, the

handset displays Speaker.

Volume

• During a call, press p/VOLUME/q to

adjust the listening volume.

Handset control key panel:

10 11

Mute

The mute function allows you to hear the

other party but the other party cannot hear

you.

• During a call, press MUTE. The handset

displays Muted.

• Press MUTE again to resume the

conversation. The handset displays

Microphone on brieﬂy.

Join a call in progress (for multiple

handset models only)

You can use up to four handsets at a time

on an outside call.

• When a handset is already on a call,

press or on another handset to

join the call.

• To exit the call, press OFF or place

the handset in the telephone base or

charger. The call continues until both

handsets hang up.

Call waiting

When you subscribe to call waiting service

from your telephone service provider, you

hear an alert tone if there is an incoming

call while you are already on a call.

• Press FLASH to put the current call on

hold and take the new call.

• Press FLASH at any time to switch back

and forth between calls.

If you also subscribe to caller ID service, it

will let you see the name and telephone

number of the caller during call waiting.

It may be necessary to change your

telephone service to use this feature.

Contact your telephone service provide if:

• You have both caller ID and call waiting,

but as separate service (you may need

to combine these service);

• You have only caller ID service, or only

call waiting service; or

• You do not subscribe to caller ID or call

waiting services.

There are fees for caller ID services. In

addition, services may not be available in

all areas.

Chain dialing

Use this feature to initiate a dialing

sequence from numbers stored in the

phonebook, caller ID log or redial list while

you are on a call.

Chain dialing can be useful if you wish

to access other numbers (such as bank

account numbers or access codes) from

the phonebook, caller ID log or redial list.

To access a number in the phonebook

while on a call:

1. Press MENU twice to enter the

phonebook.

2. Press q or p to scroll to the desired

entry.

3. Press SELECT to dial the displayed

number.

To access a number in the caller ID log

while on a call:

1. Press MENU and then press q or p to

select Caller ID log.

2. Press SELECT and then press q or p

to scroll to the desired entry.

3. Press SELECT to dial the displayed

number.

To access a number in the redial list

while on a call:

1. Press REDIAL.

2. Press q, p or REDIAL repeatedly to

browse to the desired entry.

3. Press SELECT to dial the displayed

number.

NOTES

• You cannot edit a phonebook entry while

on a call. Refer to the Phonebook section for

more details.

• You cannot copy a caller ID log entry into

the phonebook while on a call. Refer to the

Caller ID log section for more details.

• You cannot erase a redial entry while on a

call. Refer to the Redial list section for more

details.

• Press CANCEL to exit redial list, phonebook

or caller ID log when you are on a call.

Find handset

Use this feature to ﬁnd all system handsets.

To start paging:

• Press FIND HANDSET on the

telephone base when not in use.

All idle handsets ring and display

** Paging **.

To end paging:

• Press FIND HANDSET at the telephone

base.

-OR-

• Press , , OFF or any of the dialing

key on the handset.

-OR-

• Place the handset in the telephone base

or charger.

NOTES

• Press MUTE to turn off the ringer of a

handset temporarily. Paging tone continues

on the other handset.

• Do not press and hold FIND HANDSET

for more than four seconds. It may lead

to handset deregistration. If the handset

displays To register HS... and ...see manual,

refer to the Frequently asked questions

section to register the handset back to the

telephone base.

Redial list

Each handset stores the last 10 telephone

numbers dialed. Entries are shown in

reverse chronological order. When there

are already 10 entries, the oldest entry is

deleted to make room for the new entry.

Review a redial list entry

1. Press REDIAL when the handset is not

in use.

2. Press q, p or REDIAL repeatedly until

the desired entry displays.

Dial a redial list entry

1. Press REDIAL when the phone is not

in use.

2. Press q, p or REDIAL repeatedly until

the desired entry displays.

3. Press or to dial.

-OR-

1. Press or when the phone is not

in use.

2. Press REDIAL and then press q, p or

REDIAL repeatedly until the desired

entry displays.

3. Press SELECT to dial.

Delete a redial list entry

1. Press REDIAL when the handset is not

in use.

2. Press q, p or REDIAL repeatedly to

browse to the desired entry.

3. Press DELETE to delete the displayed

number. You hear a conﬁrmation tone.

12 13

Multiple handset use

Intercom

Use the intercom feature for conversations

between two handsets.

1. Press INT on your handset when not in

use.

• If you have only one handset, your

handset displays INT needs 2 HS.

• If you have two handsets, your

handset displays Calling HS X.

• If you have three or more handsets,

your handset displays Intercom

to. Use the dialing keys to enter a

destination handset. Your handset

displays Calling HS X.

The destination handset rings and its

screen displays HS X is calling.

2. To answer the intercom call, press

, , INT or any dialing key on the

destination handset. Both handsets

now display Intercom.

3. To end the intercom call, press OFF

or place the handset back in the

telephone base or charger. Both

handsets now display Intercom ended.

NOTES

• To cancel the intercom call before it is

answered, press OFF or INT.

• Press OFF or MUTE on the destination

handset to temporarily silence the intercom

ringer.

• If the destination handset does not answer

the intercom call within 100 seconds, is on a

call or out of range, the originating handset

displays Unable to call and returns to idle

mode.

• If there is an incoming call while the

originating handset displays Calling HS X,

the intercom request will be stopped and

the screen displays Incoming call.

Answer an incoming call during an

intercom call

When you receive an outside call during

an intercom call, there is an alert tone.

• To answer the outside call, press .

The intercom call ends automatically.

• To end the intercom call without

answering the outside call, press OFF.

The telephone continues to ring.

Transfer a call

Use the intercom feature to transfer an

outside call to another system handset.

1. During a call, press INT.

• If you have two handsets, the

outside call is put on hold and your

handset displays Calling HS X.

• If you have three or more handsets,

your handset displays Intercom

to. Use the dialing keys to enter a

handset number. The outside call

is put on hold and your handset

displays Calling HS X.

The destination handset rings and its

screen displays HS X is calling.

2. To answer the intercom call on the

destination handset, press , ,

INT or any dialing key on the

destination handset. The outside call is

still on hold and both handsets now

display Intercom. You can now have a

private conversation with the

destination handset.

NOTES

• To cancel the intercom call before it is

answered, press , OFF or INT.

• If the destination handset does not answer

within 100 seconds, is in use, on a call or

is out of range, the originating handset

displays Unable to call and then reconnects

to the outside call.

3. For this intercom call, you have the

following options:

• You can let the destination handset

join you on the outside call in a

three-way conversation. Press

and hold INT on the originating

handset.

• You can transfer the call. Press

OFF, or place your handset back

in the telephone base or charger.

Your handset displays Line in use.

The destination handset is then

connected to the outside call.

• You can press INT to switch

between the outside call (Outside

call displays) and the intercom call

(Intercom displays).

• The destination handset can end

the intercom call by pressing OFF,

or by placing the handset back in

the telephone base or charger.

The outside call continues with the

original system handset.

Phonebook

The phonebook can store up to 50 entries,

which are shared by all handsets. Each

entry may consist of a telephone number

up to 30 digits, and a name up to 15

characters.

Any additions, deletions or edits made

on one handset will be reﬂected on other

handsets.

If the telephone number in the

phonebook exceeds 15 digits, a dash

appears after the 14th digit and then the

remaining digits are shown beginning with

a dash, alternately.

Add a phonebook entry

1. Enter the number when the phone is

not in use. Press MENU, then go to

Step 3.

-OR-

Press MENU when the phone is not

in use, then press SELECT to choose

Phonebook. Press SELECT again to

choose Add new entry.

2. When Enter number

displays, use the

dialing keys to enter

the number.

-OR-

Copy a number

from the redial list

by pressing REDIAL and then press

q, p or REDIAL repeatedly to select

a number. Press SELECT to copy the

number.

3. Press SELECT to move

on to enter the name.

The handset displays

Enter name.

4. Use the dialing keys

to enter the name.

Additional key

presses show other characters of that

particular key. The ﬁrst character of

every word is capitalized.

Enter number

ECO ANS ON

Enter name

ECO ANS ON

14 15

5. Press SELECT to save. You hear a

conﬁrmation tone.

While entering names and numbers, you

can:

• Press DELETE to backspace and erase a

digit or character.

• Press and hold DELETE to erase the

entire entry.

• Press q or p to move the cursor to the

left or right.

• Press and hold PAUSE to insert a dialing

pause (for entering numbers only).

• Press 0 to add a space (for entering

names only).

Review a phonebook entry

Entries are sorted alphabetically.

1. Press when the phone is not in use.

2. Press q or p to browse through the

phonebook, or use the dialing keys to

start a name search.

-OR-

1. Press MENU when the phone is not in

use.

2. Press SELECT to choose Phonebook.

3. Press q or p to scroll

to Review and then

press SELECT.

4. Press q or p to

browse.

NOTE

• You hear two beeps when you reach the

beginning or end of the phonebook.

Alphabetical search

1. Follow the steps in Review a

phonebook entry to enter the

phonebook.

2. Use the dialing keys to enter the

letter associated with the name. For

example, if you have entries for Jenny,

Jessie, Kristen and Laura in your

phonebook, press 5 (JKL) once to see

Jenny (when Jenny displays, press

q to see Jessie), twice to see Kristen,

or three times to see Laura. If there is

no name entry matching your search,

the next closest match in alphabetical

order appears. If necessary, press q or

p to browse.

Delete the phonebook entries

1. Search for the

desired entry in the

phonebook (see

Review a phonebook

entry or Alphabetical

search).

2. When the desired

entry appears, press

DELETE. The handset

displays Delete

entry? and the

number.

3. Press SELECT

to conﬁrm. The handset displays

Deleting.... Then you hear a

conﬁrmation tone.

To delete all phonebook entries:

1. Press MENU when the phone is not in

use.

2. Press SELECT to choose Phonebook.

3. Press q or p to select Delete all then

press SELECT.

4. The screen displays Delete all?. Press

SELECT to conﬁrm. The handset

displays Deleting... and then you hear

a conﬁrmation tone.

Edit a phonebook entry

1. Search for the desired entry in the

phonebook (see Review a phonebook

entry or Alphabetical search).

2. When the desired entry appears, press

SELECT. The handset displays Enter

number and the stored number.

3. Use the dialing keys to edit the

number, then press SELECT. The

handset displays Enter name and then

the stored name.

4. Use the dialing keys to edit the name.

Additional key presses show other

characters of that particular key.

The ﬁrst character of every word is

capitalized.

5. Press SELECT to save. You hear a

conﬁrmation tone.

Dial a phonebook entry

1. Search for the desired entry in the

phonebook (see Review a phonebook

entry or Alphabetical search).

2. When the desired entry appears, press

or to dial.

Caller ID

If you subscribe to caller ID service,

information about each caller appears after

the ﬁrst or second ring. If you answer a call

before the caller information appears on

the screen, it will not be saved in the caller

ID log.

The caller ID log stores up to 30 entries.

Each entry has up to 24 digits for the

phone number and 15 characters for the

name.

If the telephone number has more that 15

digits, only the last 15 digits appear.

If the name has more than 15 characters,

only the ﬁrst 15 characters are shown and

saved in the caller ID log.

Entries appear in reverse chronological

order. When the caller ID log is full, the

oldest entry is deleted to make room for

new incoming call information.

Caller ID log entries are shared by all

system handsets. Any deletions made on

one handset are reﬂected on all other

handsets.

NOTE

• This product can provide information

only if both you and the caller are in areas

offering caller ID service and if both

telephone service providers use compatible

equipment. The time and date are sent by

your telephone service provider along with

the call information.

Review

ECO ANS ON

Mike Smith

800-595-9511

ECO ANS ON

Delete entry?

ECO ANS ON

16 17

Review a caller ID log entry

1. Press CID when the phone is not in

use.

2. Press q or p to browse through the

caller ID log.

-OR-

1. Press MENU when the phone is not in

use. Press q or p to select Caller ID

log.

2. Press SELECT twice and then press q

or p to browse.

NOTE

• You hear two beeps when you reach the

beginning or end of the caller ID log.

Memory match

When the incoming telephone number

matches the last seven digits of a

telephone number in your phonebook,

the screen displays the stored name of the

phonebook entry.

For example, if Linda Jones calls, her name

appears as Linda if this is how you entered

it into your phonebook.

NOTE

• The number shown in the caller ID log

is in the format sent by the telephone

service provider. It usually delivers 10-digit

telephone numbers (area code plus phone

number). If the last seven digits of the

incoming telephone number does not match

a number in your phonebook, the name

appears as it is delivered by the telephone

service provider.

Missed call indicator

When there are calls that

have not been reviewed

in the caller ID log, the

handset displays XX

missed calls.

Each time you review a

caller ID log entry marked

NEW, the number of

missed calls decreases by

one.

When you have reviewed

all the missed calls, the

missed call indicator no

longer displays.

If you do not want to review the missed

calls one by one, press and hold CANCEL

on the idle handset to erase the missed

call indicator. All the entries are then

considered old.

View dialing options

The caller ID log entries received have 10

digits (the area code plus the seven-digit

number). You may dial a 1 plus the area

code plus the seven digits.

While reviewing the caller ID log, press

(pound key) repeatedly if you

need to add or remove 1 in front of the

telephone number before dialing or

saving it in the phonebook.

Mike Smith

800-595-9511

ECO ANS ON

10:15pm 12/25

Press # 1-800-595-9511

Press # 800-595-9511

NOTE

• 7-digit local dialing will be invalid from

October 2021 onwards. Press # (pound key)

repeatedly to select the appropriate dialing

option.

Dial a caller ID log entry

When the number is shown in the correct

format for dialing, press or to dial.

Save a caller ID log entry to the

phonebook

1. When in the caller ID log, press q or

p to browse.

2. When the desired caller ID log entry

displays, press SELECT twice to choose

To Phonebook. The handset displays

Enter number and the stored number.

3. Use the dialing keys to modify the

number, if necessary. Then press

SELECT. The handset displays Enter

name and then the stored name.

4. Use the dialing keys to modify the

name, if necessary. Then press SELECT

to save. You hear a conﬁrmation tone.

While entering names and numbers, you

can:

• Press DELETE to backspace and erase a

digit or character.

• Press and hold DELETE to erase the

entire entry.

• Press q or p to move the cursor to the

left or right.

• Press and hold PAUSE to insert a dialing

pause (for entering numbers only).

• Press 0 to add a space (for entering

names only).

Delete the caller ID log entries

1. When in the caller ID log, press q or

p to browse.

2. When the desired caller ID log entry

displays, press DELETE. The handset

displays Deleting.... Then you hear a

conﬁrmation tone.

To delete all caller ID log entries:

1. Press MENU when the phone is not in

use.

2. Press q or p to select Caller ID log

and then press SELECT.

3. Press q or p to

select Delete all then

press SELECT.

4. The screen displays

Delete all?. Press

SELECT to conﬁrm.

The handset displays

Deleting... and

then you hear a

conﬁrmation tone.

XX missed calls

ECO ANS ON

10:15pm 12/25

Mike Smith

595-9511

ECO ANS ON

10:15pm 12/25

NEW

Delete all

ECO ANS ON

Delete all?

ECO ANS ON

18 19

Call block

If you have subscribed to caller ID service,

you can set the telephone to block

unknown calls and certain undesired calls.

The call block list can store up to 20 entries.

When a call is blocked, the caller will

hear a simulated busy tone for one ring

cycle. The call recipient may pick up the

call during the ﬁrst ring when there is no

caller ID information. Otherwise, the call is

disconnected.

Block unknown calls

All incoming calls with unknown numbers

will be blocked.

1. Press MENU when the phone is not in

use.

2. Press q or p to select Call block and

then press SELECT.

3. Press q or p to select Calls w/o num

then press SELECT.

4. Press q or p to choose Unblock or

Block, then press SELECT. You hear a

conﬁrmation tone.

Add a call block list entry

1. Press MENU when the phone is not in

use.

2. Press q or p to select Call block and

then press SELECT.

3. Press SELECT to choose Block list.

4. Press q or p to select Add new entry

then press SELECT.

5. When Enter number displays, use the

dialing keys to enter the number.

-OR-

Copy a number from the redial list

by pressing REDIAL and then press

q, p or REDIAL repeatedly to select

a number. Press SELECT to copy the

number.

6. Press SELECT to move on to enter

the name. The handset displays Enter

name.

7. Use the dialing keys to enter the

name. Additional key presses show

other characters of that particular key.

The ﬁrst character of every word is

capitalized.

8. Press SELECT to save. You hear a

conﬁrmation tone.

While entering names and numbers, you

can:

• Press DELETE to backspace and erase a

digit or character.

• Press and hold DELETE to erase the

entire entry.

• Press q or p to move the cursor to the

left or right.

• Press and hold PAUSE to insert a dialing

pause (for entering numbers only).

• Press 0 to add a space (for entering

names only).

Review call block list

1. Press MENU when the phone is not in

use.

2. Press q or p to select Call block and

then press SELECT.

3. Press SELECT to choose Block list.

4. Press SELECT to choose Review.

5. Press q or p to browse through the

call block list.

Edit a call block list entry

1. Search for the desired entry in the call

block list (see Review call block list).

2. When the desired entry appears, press

SELECT. The handset displays Enter

number and the stored number.

3. Use the dialing keys to edit the

number, then press SELECT. The

handset displays Enter name and then

the stored name.

4. Use the dialing keys to edit the name.

Additional key presses show other

characters of that particular key.

The ﬁrst character of every word is

capitalized.

5. Press SELECT to save. You hear a

conﬁrmation tone.

Save a caller ID log entry to the call

block list

1. When in the caller ID log, press q or

p to browse.

2. When the desired caller ID log entry

displays, press SELECT twice to choose

To Call block. The handset displays

Enter number and the stored number.

3. Use the dialing keys to modify the

number, if necessary. Then press

SELECT. The handset displays Enter

name and then the stored name.

4. Use the dialing keys to modify the

name, if necessary. Then press SELECT

to save. You hear a conﬁrmation tone.

Delete a call block list entry

1. Search for the desired entry in the call

block list (see Review call block list).

2. When the desired call block list entry

displays, press DELETE and you hear a

conﬁrmation tone.

Mute ﬁrst ring

An incoming call will ring once and then

the system will check if the call should be

blocked. You can choose to mute the ﬁrst

ring for all incoming calls, so that there will

be no ring for blocked calls. By default, the

ﬁrst ring is set to On.

1. Press MENU when the handset is not

in use.

2. Press 7464# on the handset.

3. Press q or p to choose First ring:On

to keep the ﬁrst ring, or First ring:Off

to mute the ﬁrst ring.

4. Press SELECT to save. You hear a

conﬁrmation tone.

NOTE

• If you have muted the ﬁrst ring, you will hear

one ring less before the voicemail answers

the incoming calls.

20 21

Sound settings

Key tone

You can turn the key tone on or off for

each handset.

1. Press MENU when the handset is not

in use.

2. Press q or p to choose Settings and

then press SELECT.

3. Press q or p to choose Key tone, then

press SELECT.

4. Press q or p to choose On or Off,

then press SELECT to save. You hear a

conﬁrmation tone.

Ringer tone

You can choose from different ringer tones

for each handset.

1. Press MENU when the handset is not

in use.

2. Press q or p to choose Ringers and

then press SELECT.

3. Press q or p to choose Ringer tone,

then press SELECT.

4. The screen displays Tone: with the

current setting displayed. Press q or

p to sample each ringer tone.

5. Press SELECT to save. You hear a

conﬁrmation tone.

NOTE

• If you turn off the ringer volume, you will not

hear ringer tone samples.

Ringer volume

You can adjust the handset ringer volume

level, or turn the ringer off.

1. Press MENU when the handset is not

in use.

2. Press q or p to choose Ringers and

then press SELECT twice.

3. Press q or p to sample each ringer

volume level.

4. Press SELECT to save. You hear a

conﬁrmation tone.

NOTES

• If the ringer volume is set to Off, the idle

screen displays .

• When the ringer volume is set to Off, the

handset still rings when you press FIND

HANDSET at the telephone base.

Temporary ringer silencing

When the telephone is ringing, you can

temporarily silence the ringer without

disconnecting the call. The next call rings

normally at the preset volume.

• Press CANCEL or MUTE. The handset

displays Ringer muted and .

Quiet mode

You can turn on the quiet mode for a

period of time (1-12 hours). During this

period, all tones (except paging tone) are

muted.

To set the duration and turn on the

quiet mode:

1. Press and hold when the

handset is not in use.

2. The handset displays Quiet: _ _ hours.

Use the dialing keys (0-9) to enter the

desired duration (1-12).

3. Press SELECT to save. You hear a

conﬁrmation tone.

The handset displays Quiet mode on and

NOTE

• When you change the settings of the ringer

tone or ringer volume, you can still hear the

samples even if the quiet mode is on.

To turn off the quiet mode:

• Press and hold when the

handset is not in use. The handset

displays Quiet mode off brieﬂy and

then returns to idle.

Retrieve voicemail from

telephone service

Voicemail is a feature available from most

telephone service providers. It may be

included with your telephone service, or

may be optional. Fees may apply.

Retrieve voicemail

When you received a

voicemail, the handset

displays and New

voicemail.

To retrieve, you typically

dial an access number

provided by your

telephone service provider, and then enter

a security code. Contact your telephone

service provider for instructions on how to

conﬁgure the voicemail settings and listen

to messages.

NOTE

• After you have listened to all new voicemail

messages, the indicators on the handset turn

off automatically.

Set your voicemail number

You can save your access number on each

handset for easy access to your voicemail.

After you saved the voicemail number, you

can press and hold to retrieve

voicemail.

1. Press and hold when the phone is

not in use.

2. Use the dialing keys to enter the

voicemail number (up to 30 digits).

3. Press SELECT to save. Then the handset

dials the saved voicemail number.

-OR-

1. Press MENU when the handset is not

in use.

2. Press q or p to choose Settings and

then press SELECT.

3. Press q or p to choose Voicemail #

and then press SELECT.

4. Use the dialing keys to enter the

voicemail number (up to 30 digits).

5. Press SELECT to save. You hear a

conﬁrmation tone.

While entering numbers, you can:

• Press DELETE to backspace and erase a

digit.

• Press and hold DELETE to erase the

entire entry.

• Press q or p to move the cursor to the

left or right.

• Press and hold PAUSE to insert a dialing

pause.

Turn off the new voicemail

indicators

If you have retrieved your voicemail while

away from home, and the handset still

displays the new voicemail indicators, use

this feature to turn off the indicators.

NOTE

• This feature turns off the indicators only, it

does not delete your voicemail messages.

1. Press MENU when the phone is not in

use.

2. Press q or p to choose Settings and

then press SELECT.

3. Press q or p to

choose Clr voicemail

and then press

SELECT. You hear a

conﬁrmation tone.

New voicemail

ECO ANS ON

10:15pm 12/25

Clr voicemail

ECO ANS ON

22 23

Screen messages

Calling HS X

(for models with two

or more handsets

only)

You are calling

another handset (for

intercom calls).

Ended You have just ended

a call.

HS X is

calling

(for models with two

or more handsets

only)

Another handset is

calling (for intercom

calls).

Incoming

call

There is an incoming

call.

INT needs 2

Two handsets are

required for an

intercom call.

Intercom The handset is on an

intercom call.

Intercom

ended

The intercom call has

just ended.

Intercom to

(for models with

three or more

handsets only)

You have started the

intercom process or

started transferring

a call, and need to

enter the desired

handset number.

Line in use A system handset is

in use, or another

telephone on the

same line is in use.

List empty There are no

phonebook entries,

caller ID log entries

or call block list

entries.

Low battery The battery needs to

be recharged.

Microphone

MUTE is turned off

and the person on

the other end can

hear you.

Muted You have turned

off the handset

microphone. The

other party cannot

hear you but you can

hear the other party.

New

voicemail

There are new

voicemail message(s)

from the telephone

service provider.

No battery No battery is

installed. Follow the

directions for battery

installation on page 4

to install the battery

before charging.

No line There is no

telephone line

connected.

Not

available

Another handset is

already reviewing the

phonebook, caller ID

log or call block list.

Number

repeated

The telephone

number you enter is

already stored in the

phonebook.

Out of range

or no pwr at

base

The handset cannot

communicate with

the telephone base.

Check the telephone

base power

connection or move

the handset closer to

the telephone base.

Phone The handset is on a

call.

PRIVATE NAME The caller is

blocking the name

information.

PRIVATE

NUMBER

The caller is blocking

the telephone

number information.

PRIVATE

CALLER

The caller is blocking

the name and the

telephone number

information.

Put in

charger

The battery is

very low. Place

the handset in the

telephone base

or charger for

recharging.

Quiet mode

off

The quiet mode is

turned off.

Quiet mode

The quiet mode is

turned on.

Rec mem full The phonebook is

full.

Reg. failed The handset

registration is not

successful.

Registering

...

The handset

registration is in

progress.

Ringer muted The handset ringer

is muted temporarily

during an incoming

call.

Ringer off The handset ringer is

turned off.

Speaker The handset

speakerphone is in

use.

To register

HS...

...see

manual

Screen display on

a non-registered

handset.

Unable to

call

Failed phone call (the

other handset is in

use).

UNKNOWN NAME This caller’s name is

unavailable.

UNKNOWN

NUMBER

This caller’s number is

unavailable.

UNKNOWN

CALLER

No caller information

is available about this

caller.

XX missed

calls

There are calls that

have not been

reviewed in the caller

ID log.

** Paging ** The system handsets

are being paged.

ECO mode

This power conserving technology reduces

power consumption for optimal battery

performance. The ECO mode activates

automatically whenever the handset is

synchronized with the telephone base.

24 25

General product care

Taking care of your telephone

Your cordless telephone contains

sophisticated electronic parts, so it must be

treated with care.

Avoid rough treatment

Place the handset down gently. Save the

original packing materials to protect your

telephone if you ever need to ship it.

Avoid water

Your telephone can be damaged if it gets

wet. Do not use the handset outdoors in

the rain, or handle it with wet hands. Do

not install the telephone base near a sink,

bathtub or shower.

Electrical storms

Electrical storms can sometimes cause

power surges harmful to electronic

equipment. For your own safety, take

caution when using electrical appliances

during storms.

Cleaning your telephone

Your telephone has a durable plastic casing

that should retain its luster for many years.

Clean it only with a dry non-abrasive cloth.

Do not use dampened cloth or cleaning

solvents of any kind.

Frequently asked questions

Below are the questions most frequently

asked about the cordless telephone. If you

cannot ﬁnd the answer to your question,

visit our website at

www.vtechphones.com or call

1 (800) 595-9511 for customer service. In

Canada, visit phones.vtechcanada.com or

call 1 (800) 267-7377.

My telephone

does not work

at all.

Make sure the telephone

base is installed properly,

and battery is installed

and charged correctly.

For optimum daily

performance, return the

handset to the telephone

base after use.

The display

shows No line. I

cannot hear the

dial tone.

Disconnect the telephone

line cord from your

telephone and connect it

to another telephone. If

there is no dial tone on that

other telephone either,

then the telephone line

cord may be defective. Try

installing a new telephone

line cord.

If changing the telephone

line cord does not help,

the wall jack (or the wiring

to this wall jack) may

be defective. Contact

your telephone service

provider.

You may be using a new

cable or VoIP service, the

existing telephone jacks in

your home may no longer

work. Contact your service

provider for solutions.

I cannot dial out. Make sure there is a dial

tone before dialing. It

is normal if the handset

takes a second or two

to synchronize with the

telephone base before

producing a dial tone. Wait

an extra second before

dialing.

Eliminate any background

noise. Mute the handset

before dialing, or dial from

another room in your home

with less background

noise.

The display

shows To

HS... and

...see manual

alternately. The

handset does

not work at all.

The handset is

deregistered from the

telephone base.

Place the handset in the

telephone base to register

it back. The handset

shows Registered when

the registration process

completes. This process

takes about 60 seconds to

complete.

The display

shows Low

battery.

Place the handset in the

telephone base or charger

for charging.

The battery

does not charge

in the handset

or the handset

battery does not

accept charge.

Make sure the handset is

placed in the telephone

base or charger correctly.

If the battery is completely

depleted, charge the

battery for at least

30 minutes before use.

You may need to purchase

a new battery.

The telephone

does not ring

when there is an

incoming call.

Make sure the ringer

volume is not set to off.

The handset may be too

far from the telephone

base. Move it closer to the

telephone base.

My handset

beeps and is

not performing

normally.

Move the handset closer to

the telephone base. It may

be out of range.

I hear noise on

the cordless

handset and

the keys do not

work.

Make sure the telephone

line cord is plugged in

securely.

I hear other calls

when using the

telephone.

Disconnect the telephone

base from the telephone

wall jack. Plug in a different

telephone. If you still hear

other calls, the problem is

probably in the wiring or

telephone service. Contact

your telephone service

provider.

There is

interference

during a

telephone

conversation.

My calls fade

out when

I am using

the cordless

handset.

The handset may be out of

range. Move it closer to the

telephone base.

If you subscribe to high-

speed Internet service (DSL

- digital subscriber line)

through your telephone

line, you must install a

DSL ﬁlter between the

telephone line cord

and the telephone wall

jack. The ﬁlter prevents

noise and caller ID

problems caused by DSL

interference. Contact your

DSL service provider for

more information about

DSL ﬁlters.

Appliances or other

cordless telephones

plugged into the same

circuit as the telephone

base can cause

interference. Try moving

the appliance or telephone

base to another outlet.

The location of your

telephone base can

impact the performance

of your cordless phone.

For better reception,

install the telephone base

in a centralized location

within your home or

ofﬁce, away from walls

or other obstructions.

In many environments,

elevating the telephone

base improves overall

performance.

26 27

The telephone

does not

receive caller

ID or the

telephone does

not show caller

ID during call

waiting.

Caller ID is a subscription

service. You must subscribe

to this service from your

telephone service provider

for this feature to work on

your telephone.

Both your and the caller’s

telephone service

providers must use

equipment compatible

with the caller ID service.

The caller may not be

calling from an area which

supports caller ID.

The caller ID information

displays after the ﬁrst or

second ring.

The display

shows Out of

range or no pwr

at base.

The handset may be out of

range. Move it closer to the

telephone base.

Make sure the power cord

is securely plugged into

the telephone base. Use

a working electrical outlet

not controlled by a wall

switch.

I subscribe to a

nontraditional

telephone

service that uses

my computer

to establish

connections,

and my

telephone

doesn’t work.

Make sure your computer

is powered on, and

your Internet is working

properly.

Make sure to plug your

USB telephone adapter

into a dedicated USB port

on your computer. Do not

plug into a multiple port

USB hub (USB splitter) that

is not powered.

In a few rare instances, the

USB port on your computer

may not have enough

power. In these instances,

try using a USB hub with

its own external power

supply.

If you are using a ﬁrewall, it

may prevent access to your

nontraditional telephone

service. Contact your

service provider for more

information.

I accidentally

set my LCD

language to

Spanish or

French, and I

don’t know how

to change it

back to English.

While the handset is not in

use, press MENU and then

enter 364# to change

the handset LCD language

back to English.

The RBRC seal

The RBRC seal on the nickel-metal

hydride battery indicates that VTech

Communications, Inc. is voluntarily

participating in an industry program to

collect and recycle these batteries at the

end of their useful lives, when taken out

of service within the United States and

Canada.

The program provides a convenient

alternative to placing used nickel-

metal hydride batteries into the trash or

municipal waste, which may be illegal in

your area.

VTech’s participation makes it easy for

you to drop off the spent battery at local

retailers participating in the program

or at authorized VTech product service

centers. Please call 1 (800) 8 BATTERY® for

information on Ni-MH battery recycling

and disposal bans/restrictions in your

area. VTech’s involvement in this program

is part of its commitment to protecting

our environment and conserving natural

resources.

The RBRC seal and 1 (800) 8 BATTERY® are

registered trademarks of Call2recycle, Inc.

FCC, ACTA and IC regulations

FCC Part 15

NOTE: This equipment has been

tested and found to comply with

the requirements for a Class B digital

device under Part 15 of the Federal

Communications Commission (FCC) rules.

These requirements are intended to

provide reasonable protection against

harmful interference in a residential

installation. This equipment generates,

uses and can radiate radio frequency

energy and, if not installed and used in

accordance with the instructions, may

cause harmful interference to radio

communications. However, there is no

guarantee that interference will not occur

in a particular installation. If this equipment

does cause harmful interference to radio

or television reception, which can be

determined by turning the equipment off

and on, the user is encouraged to try to

correct the interference by one or more of

the following measures:

• Reorient or relocate the receiving

antenna.

• Increase the separation between the

equipment and receiver.

• Connect the equipment into an outlet on

a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced

radio/TV technician for help.

WARNING: Changes or modiﬁcations to

this equipment not expressly approved

by the party responsible for compliance

could void the user’s authority to operate

the equipment.

This device complies with Part 15 of the

FCC rules. Operation is subject to the

following two conditions: (1) this device

may not cause harmful interference,

and (2) this device must accept any

interference received, including

28 29

interference that may cause undesired

operation. Privacy of communications

may not be ensured when using this

telephone.

To ensure safety of users, the FCC has

established criteria for the amount of

radio frequency energy that can be

safely absorbed by a user or bystander

according to the intended usage of the

product. This product has been tested and

found to comply with the FCC criteria. The

handset may be safely held against the

ear of the user. The telephone base shall

be installed and used such that parts of

the user’s body other than the hands are

maintained at a distance of approximately

20 cm (8 inches) or more.

This Class B digital apparatus complies

with Canadian requirement:

CAN ICES-3 (B)/NMB-3(B)

FCC Part 68 and ACTA

This equipment complies with Part

68 of the FCC rules and with technical

requirements adopted by the

Administrative Council for Terminal

Attachments (ACTA). The label on the back

or bottom of this equipment contains,

among other things, a product identiﬁer

in the format US:AAAEQ##TXXXX. This

identiﬁer must be provided to your

telephone service provider upon request.

The plug and jack used to connect this

equipment to premises wiring and the

telephone network must comply with

applicable Part 68 rules and technical

requirements adopted by ACTA. A

compliant telephone cord and modular

plug is provided with this product. It is

designed to be connected to a compatible

modular jack that is also compliant. An

RJ11 jack should normally be used for

connecting to a single line and an RJ14

jack for two lines. See the installation

instructions in the user’s manual.

The Ringer Equivalence Number (REN) is

used to determine how many devices you

may connect to your telephone line and

still have them ring when you are called.

The REN for this product is encoded as the

6th and 7th characters following the US: in

the product identiﬁer (e.g., if ## is 03, the

REN is 0.3). In most, but not all areas, the

sum of all RENs should be ﬁve (5.0) or less.

For more information, please contact your

telephone service provider.

This equipment must not be used with

Party Lines. If you have specially wired

alarm dialing equipment connected

to your telephone line, ensure the

connection of this equipment does not

disable your alarm equipment. If you have

questions about what will disable alarm

equipment, consult your telephone service

provider or a qualiﬁed installer.

If this equipment is malfunctioning, it must

be unplugged from the modular jack

until the problem has been corrected.

Replacement to this telephone equipment

can only be made by the manufacturer

or its authorized agents. For replacement

procedures, follow the instructions

outlined under the Limited warranty.

If this equipment is causing harm to the

telephone network, the telephone service

provider may temporarily discontinue

your telephone service. The telephone

service provider is required to notify you

before interrupting service. If advance

notice is not practical, you will be notiﬁed

as soon as possible. You will be given

the opportunity to correct the problem

and the telephone service provider is

required to inform you of your right to ﬁle

a complaint with the FCC. Your telephone

service provider may make changes in

its facilities, equipment, operation, or

procedures that could affect the proper

functioning of this product. The telephone

service provider is required to notify you if

such changes are planned.

If this product is equipped with a corded

or cordless handset, it is hearing aid

compatible.

If this product has memory dialing

locations, you may choose to store

emergency telephone numbers (e.g.,

police, ﬁre, medical) in these locations. If

you do store or test emergency numbers,

please:

Remain on the line and brieﬂy explain the

reason for the call before hanging up.

Perform such activities in off-peak hours,

such as early morning or late evening.

Industry Canada

This device contains licence-exempt

transmitter(s)/receiver(s) that comply

with Innovation, Science and Economic

Development Canada’s licence-exempt

RSS(s). Operation is subject to the

following two conditions:

(1) This device may not cause interference.

(2) This device must accept any

interference, including interference that

may cause undesired operation of the

device.

Privacy of communications may not be

ensured when using this telephone.

The term ‘’IC:‘’ before the certiﬁcation/

registration number only signiﬁes that the

Industry Canada technical speciﬁcations

were met.

The Ringer Equivalence Number (REN) for

this terminal equipment is 0.1. The REN

indicates the maximum number of devices

allowed to be connected to a telephone

interface. The termination of an interface

may consist of any combination of devices

subject only to the requirement that the

sum of the RENs of all the devices not

exceed ﬁve.

This product meets the applicable

Innovation, Science and Economic

Development Canada technical

speciﬁcations.

California Energy Commission

battery charging testing

instructions

This telephone is set up to comply with the

energy-conserving standards right out of

the box. These instructions are intended for

California Energy Commission (CEC) compliance

testing only. When the CEC battery charging

testing mode is activated, all telephone

functions, except battery charging, will be

disabled.

To activate the CEC battery charging testing

mode:

1. Unplug the telephone base power

adapter from the power outlet. Make sure

all handsets are plugged with charged

batteries before proceeding.

2. While you press and hold

FIND HANDSET, plug the telephone base

power adapter back to the power outlet.

3. After about 20 seconds, when the

IN USE light starts ﬂashing, release

FIND HANDSET and then press it again

within 2 seconds.

NOTES

• When the phone successfully enters the CEC

battery charging testing mode, the IN USE light

turns off and all handsets display To register HS...

and ...see manual alternatively.

• When the phone fails to enter this mode, repeat

Step 1 through Step 3 above.

To deactivate the CEC battery charging testing

mode:

1. Unplug the telephone base power adapter

from the power outlet, then plug it back in.

Then the telephone base is powered up as

normal.

2. Place the handset in the telephone base

to register it back. The handset displays

Registering....

NOTE

• The handset shows Registered when the

registration process completes. The registration

process takes about 60 seconds to complete.

30 31

For C-UL compliance only

Mesures de sécurité importantes

Aﬁn de réduire les risques d’incendie, de

blessures corporelles ou d’électrocution,

suivez toujours ces mesures préventives de

base lorsque vous utilisez votre téléphone :

1. Lisez et comprenez bien toutes les

instructions.

2. Observez toutes les instructions et mises

en garde inscrites sur l’appareil.

3. Débranchez ce téléphone de la prise

murale avant de le nettoyer. N’utilisez

pas de nettoyeurs liquides ni en

aérosol. N’utilisez qu’un chiffon doux et

légèrement humecté.

4. ATTENTION: Ne pas installer le socle

téléphonique à une hauteur supérieure

à 2 mètres.

5. N’utilisez pas ce produit près de l’eau,

tel que près d’un bain, d’un lavabo, d’un

évier de cuisine, d’un bac de lavage

ou d’une piscine, ou dans un sous-sol

humide ou sous la douche.

6. Ne déposez pas ce téléphone sur un

chariot, support ou table chancelants.

L’appareil pourrait tomber et être

sérieusement endommagé.

7. Évitez d’installer le système

téléphonique dans les endroits

soumis à une température extrême,

à la lumière directe du soleil ou à

proximité immédiate d’autres appareils

électriques ou électroniques. Protégez

votre téléphone contre les sources

d’humidité, la poussière, les vapeurs et

les liquides corrosifs.

8. Le boîtier de l’appareil est doté de

fentes et d’ouvertures d’aération

situées à l’arrière ou en dessous.

Aﬁn d’empêcher la surchauffe, ces

ouvertures ne doivent pas être

obstruées en plaçant l’appareil sur

un lit, divan, tapis ou autre surface

similaires. Ne placez pas cet appareil à

proximité d’un élément de chauffage

ni d’une plinthe électrique. De plus, ne

l’installez pas dans une unité murale ou

un cabinet fermé qui ne possède pas

d’aération adéquate.

9. Ne faites fonctionner cet appareil

qu’avec le type d’alimentation indiqué

sur les étiquettes de l’appareil. Si vous

ne connaissez pas le voltage de votre

maison, consultez votre marchand ou

votre fournisseur d’électricité.

10. Ne déposez rien sur le cordon

d’alimentation. Installez cet appareil

dans un endroit sécuritaire, là où

personne ne pourra trébucher sur

la ligne d’alimentation ni le cordon

téléphonique modulaire.

11. N’insérez jamais d’objets à travers les

fentes et ouvertures de cet appareil, car

ils pourraient toucher à des points de

tension dangereux ou court-circuiter

des pièces, ce qui constituerait un

risque d’incendie ou d’électrocution.

N’échappez pas de liquides dans

l’appareil.

12. Aﬁn de réduire les risques

d’électrocution, ne démontez pas

l’appareil, mais apportez-le plutôt à

un centre de service qualiﬁé s’il doit

être réparé. En enlevant le couvercle,

vous vous exposez à des tensions

dangereuses ou autres dangers

similaires. Un remontage inadéquat

peut être à l’origine d’une électrocution

lors d’une utilisation ultérieure de

l’appareil. Débranchez l’appareil avant

de procéder au nettoyage. Utilisez un

chiffon humide et doux.

13. Ne surchargez pas les prises de courant

et les rallonges.

14. Débranchez cet appareil de la prise

de courant et communiquez avec le

département de service à la clientèle de

VTech dans les cas suivants :

• Lorsque le cordon d’alimentation est

endommagé ou écorché.

• Si du liquide a été échappé dans

l’appareil.

• Si l’appareil a été exposé à une source

d’humidité telle que la pluie ou l’eau.

• Si le produit ne fonctionne pas

normalement en respectant les

instructions de fonctionnement.

Réglez uniquement les commandes

indiquées dans le les instructions

de fonctionnement. Les réglages

incorrects des autres commandes

pourraient provoquer un dommage

qui pourrait exiger un travail exhaustif

de la part d’un technicien autorisé aﬁn

de rétablir le fonctionnement normal

de l’appareil.

• Si le produit a été échappé et que

le socle et/ou le combiné a été

endommagé.

• Si le produit afﬁche une nette

diminution de sa performance.

15. Évitez d’utiliser un téléphone (autre

qu’un sans ﬁl) pendant un orage. Les

éclairs peuvent être à l’origine d’une

électrocution.

16. N’utilisez pas le téléphone pour

rapporter une fuite de gaz à proximité

de la fuite. En certaines circonstances,

une ﬂammèche pourrait être

provoquée lorsque l’adaptateur

est branché à une prise de courant,

ou lorsque le combiné est déposé

sur le socle. Ceci est un événement

commun associé à la fermeture d’un

circuit électrique. L’utilisateur ne

devrait pas brancher le téléphone à

une prise de courant, et ne devrait

pas déposer le combiné chargé sur

le socle, si le téléphone se trouve à

proximité d’un endroit comportant des

concentrations de gaz inﬂammables, à

moins que la ventilation soit adéquate.

Une ﬂammèche dans un tel endroit

pourrait provoquer un incendie ou

une explosion. De tels environnements

peuvent comprendre: des endroits où

l’on utilise de l’oxygène médical sans

ventilation adéquate; des gaz industriels

(dissolvants de nettoyage, des vapeurs

d’essence, etc.); une fuite de gaz

naturel, etc.

17. Ne placez que le combiné de votre

téléphone près de votre oreille

lorsqu’en mode de conversation.

18. Ces adaptateurs ont été conçus pour

être orientés en position verticale ou

montés au sol. Les broches ne sont pas

conçues pour maintenir l’adaptateur en

place si celui-ci est barnché dans une

prise au plafond ou sous une table/

armoire.

19. Pour le MATERIEL RACCORDE PAR

PRISE DE COURANT, le socle de prise

de courant doit etre installe a proximite

du materiel et doit etre aisement

accessible.

20. MISE EN GARDE: Il peut y avoir

un risque d’explosion si vous utilisez le

mauvais type de piles pour le

téléphone. N’utilisez que les piles

rechargeable inclus ou les piles de

rechange (BT262342). N’incinérez pas

les piles. Celles-ci risqueraient

d’exploser. Mettre au rebut les batteries

usagées conformément aux instructions

du fabricant. Débrancher les lignes

téléphoniques avant le remplacement

des piles.

• Évite d’utiliser la batterie dans les

conditions suivantes:

• des températures extrêmes faibles

ou élevées auxquelles une batterie

peut être soumise pendant

l’utilisation, le stockage ou le

transport.

• remplacement d’une batterie

par un type incorrect pouvant

supprimer une protection.

• mise au rebut d’une batterie

dans un feu ou dans un four

chaud, ou écrasement mécanique

ou coupure d’une batterie,

susceptible de provoquer une

explosion.

• maintien d’une batterie dans

un environnement à très haute

température pouvant provoquer

une explosion ou la fuite de liquide

ou de gaz inﬂammables.

La page charge ...

VTech CS5119 Manuel utilisateur

Marque: VTech

Modèle: CS5119

Catégorie: Téléphones

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: VTech CS5119 User manual

VTech CS5119 Manuel utilisateur

Ce manuel convient également à

VTech CS5119 Manuel utilisateur

dans d''autres langues

Documents connexes