VTech SM8252-2 Guide de démarrage rapide

VTech
Marque
VTech
Modèle
SM8252-2
Catégorie
Moniteurs vidéo bébé
Taper
Guide de démarrage rapide
Specifications are subject to change without notice.
© 2018 VTech Communications, Inc. All rights reserved.
11/18. SM8252-2_QSG_V2.
Document order number: 96-012216-020-100
Quick start guide
SM8252-2
Full Color Video Monitor
Go to www.vtechphones.com
to register your product for
enhanced warranty support and
the latest VTech product news.
What’s in the box 2 Connect the baby monitor
5
Strangulation
Hazard
Keep this cord out of reach of children.
The cord needs to be at least three feet
away from the child at all times. Do not
use with an extension cord. Do not
remove this tag.
Éloignez ce cordon des enfants. Le
cordon doit se trouver à au moins trois
pieds d’un enfant et ce, en tout temps.
N’utilisez pas de rallonge. Ne retirez pas
cette étiquette.
Mantenga este cable fuera de la alcance
de los niños. Este cable debe estar por
lo menos tres pies fuera de la alcance
del niño en todo momento. No lo use
con una extensión inalámbrica. No quite
esta etiqueta.
Risque
d’étranglement
Riesgo de
estrangulación
Strangulation
Hazard
Keep this cord out of reach of children.
The cord needs to be at least three feet
away from the child at all times. Do not
use with an extension cord. Do not
remove this tag.
Éloignez ce cordon des enfants. Le
cordon doit se trouver à au moins trois
pieds d’un enfant et ce, en tout temps.
N’utilisez pas de rallonge. Ne retirez pas
cette étiquette.
Mantenga este cable fuera de la alcance
de los niños. Este cable debe estar por
lo menos tres pies fuera de la alcance
del niño en todo momento. No lo use
con una extensión inalámbrica. No quite
esta etiqueta.
Risque
d’étranglement
Riesgo de
estrangulación
NOTESNOTE
• Use only the power adapters supplied with this product.
• Make sure the baby monitor is not connected to a switch-controlled electric outlet.
• Connect the power adapters in a vertical or floor mount position only. The adapters’ prongs are not
designed to hold the weight of baby monitor, so do not connect them to any ceiling, under-the-
table, or cabinet outlets. Otherwise, the adapters may not properly connect to the outlets.
• Make sure the parent unit, the baby units and the power adapter cords are out of reach of children.
63ē
Caution
• The default volume of your parent unit
is level 4, and the maximum volume is
level 7. If you experience high-pitched
screeching noise from your baby
monitor while positioning:
- Make sure your baby units and parent
unit are more than 3 feet (1 meter) apart,
OR
- Lower the volume of your parent unit.
4
Positioning the baby monitor
> 3ft (1m)
3
Power on or off the baby monitor
Slide the ON/OFF switch to power
on or off your baby unit.
Press and hold POWER to power on or
off your parent unit.
5
Adjust speaker volume
Press VOL / VOL to adjust your
parent unit speaker volume. Even if you
have set the parent unit volume to the
maximum, you may not hear sound from
the baby unit. It depends on the sound
sensitivity setting.
Zoom
Press to zoom in or out.
Talk to your baby unit
Press and hold TALK and speak to your
parent unit. Your voice is transmitted to
the baby unit.
Turn off the parent unit
Press and hold POWER to power off
your parent unit.
63ē
Use the menu
Press to enter the menu, choose a menu
item, or save a setting. You can use the parent
unit for advanced settings or operations,
such as to play or stop the baby unit lullaby,
or to adjust the baby unit sound sensitivity.
While in the menu:
• Press or to scroll among the menu
options.
• Press or to select an item.
• Press to return to the main menu or idle
screen.
Turn off the screen
Press and hold LCD ON/OFF to switch off
the screen. You can still hear sound from the
baby unit.
Tip
• Press any keys on the parent unit to turn on
the screen again.
63ē
ē
63ē
Press and hold
Basic operation - Parent unit
Alert tone
Low Battery Tone
No Link Alert
Sound alert in split-view
LCD is turning off...
6U]KXOTMULL
6U]KXOTMULL
Long press
Long press
Strangulation
Hazard
Keep this cord out of reach of children.
The cord needs to be at least three feet
away from the child at all times. Do not
use with an extension cord. Do not
remove this tag.
Éloignez ce cordon des enfants. Le
cordon doit se trouver à au moins trois
pieds d’un enfant et ce, en tout temps.
N’utilisez pas de rallonge. Ne retirez pas
cette étiquette.
Mantenga este cable fuera de la alcance
de los niños. Este cable debe estar por
lo menos tres pies fuera de la alcance
del niño en todo momento. No lo use
con una extensión inalámbrica. No quite
esta etiqueta.
Risque
d’étranglement
Riesgo de
estrangulación
1
Install the battery
THIS SIDE UP
5 Status check
Once you power on both your baby units and parent unit, your
parent unit displays image from the baby unit, and the LINK LED
light turns on.
If you are viewing baby unit , the
POWER LED light of baby unit turns
on. As baby unit is not being viewed,
its POWER LED light flashes.
NOTESNOTE
Note
• If you power on only one baby unit, you may see the parent unit displaying and then
No link to CAM # (# represents the baby unit number), and the LINK LED light flashing.
Press VIEW in Single CAM or Patrol mode to switch to the baby unit you have powered on.
In Single CAM or Patrol mode, press
VIEW to switch between the image of
baby units and .
Change different views - Single CAM
Monitoring Mode
Single CAM
Patrol
Split
Press VIEW
Select Patrol as your monitoring mode
to alternately view the image from baby
unit and every 10 seconds.
Change different views - Patrol
Monitoring Mode
Single CAM
Patrol
Split
10s
6U]KXOTMUT
6U]KXOTMUT
6U]KXOTMULL
Long press Long press
Select Split as your monitoring mode to
view the images from both baby units
at once.
Change different views - Split
Monitoring Mode
Single CAM
Patrol
Split
> 3ft (1m)
< 3ft (1m)
NOTESNOTE
Notes
• To avoid interference from other electronic
devices, place your baby monitor at least
3 feet (1 meter) away from devices such as
wireless routers, microwaves, cell phones
and computers.
≥
< 3ft (1m)
3ft (1m)
Mount the baby unit on dry wall (optional)
Sound sensitivity and sound activation
Insert the screws into the holes and tighten
the screws until only 1/4 inch of the screws
are exposed.
Dim mode
With dim mode preset to
on, your parent unit display
will dim to conserve energy
after 10 minutes of inactivity,
in which there is neither key
pressed nor alert received
from the baby units.
10 min inactivity
Press any buttons
NOTESNOTE
• If you do not want LCD to dim automatically, turn off the Dim Mode.
LCD
Brightness
Dim Mode
Dim Mode
On
LCD
Brightness
Dim Mode
Dim Mode
On
Use a pencil to mark two holes in
parallel. Make sure they are the same
distance apart as the wall mount holes
on the baby unit.
NOTESNOTE
Note
• Check for reception strength and camera
angle before drilling the holes.
2 screws
2 anchors
Night vision
The baby units have infrared LEDs that
allow you to see your baby clearly at
night or in a dark room. When the baby
unit being viewed detects low light
levels, the infrared LEDs are switched
on automatically. The images from the
baby unit are in black and white, and
appears on the screen.
Notes
• It is normal if you see a short white glare
on your parent unit screen as the baby unit
is adapting to the dark environment.
• When the infrared LEDs are on, the images
are in black and white. This is normal.
Tip
• Depending on the surroundings and other
interfering factors, like lightings, objects,
colors and backgrounds, the video quality
may vary. Adjust the baby units’ angle or
place the baby units at a higher level to
prevent glare and blurry display.
Overview - Parent unit
POWER
TALK
MENU/SELECT
Volume
Microphone
VIEW / LCD ON/OFF
LED lights
Zoom
Arrow keys
Stand
Power jack
Speaker
Antenna
Battery compartment
cover
Align the wall mount holes at the bot-
tom of the baby unit with the screws on
the wall. Slide the baby unit down until
it locks into place.
Adjust the camera angle.
Drill two holes in the wall.
If you drill the holes into a stud, go to
step 3.
-OR-
If you drill the holes into an object other
than a stud, insert the wall anchors into
the holes. Tap gently on the ends with a
hammer until the wall anchors are flush
with the wall.
Overview - Baby unit
ON/OFF switch
Speaker
5
Power jack
Light sensor
Camera
Microphone
POWER LED light
Infrared LEDs
Wall mount holes
Items to purchase
You will need to purchase the
following items separately to
mount your baby unit:
NOTESNOTE
Note
• The types of screws and anchors
you need depend on the
composition of the wall.
When sound activation is on, the parent unit screen stays off
to save power when the baby unit detects no sound.
Once the baby unit detects sounds that are louder than the
chosen sound sensitivity level, the parent unit screen turns
on automatically. It will then turn off again after 50 seconds
of no sound detection.
Sound-activated Screen
On
O
Sound activation
With sound sensitivity setting, you can choose to hear sounds from the
baby unit all the time, or to hear sounds that exceed a certain level. The
default level Highest allows you to hear all sounds (including background
noises).
If you set the sound sensitivity to
a lower level (e.g. Medium), you
will only hear sounds that exceed
the selected level. The baby unit
may not detect soft sounds, and
the parent unit speaker may remain
quiet.
For details, please see Adjust the
sound sensitivity of the baby unit
in the User’s manual.
VOX Sensitivity
Low
Medium
High
Highest
Sound sensitivity
63ē
  • Page 1 1
  • Page 2 2

VTech SM8252-2 Guide de démarrage rapide

VTech
Marque
VTech
Modèle
SM8252-2
Catégorie
Moniteurs vidéo bébé
Taper
Guide de démarrage rapide
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes