Pioneer SX-S30 Manuel utilisateur

English

Français

Español

Language select / Sélection de la langue / Selección de idioma

SX-S30

E

N

Before Start

What's in the box .................................................................... 2

Part Names

Front Panel ............................................................................. 3

Rear Panel .............................................................................. 4

Remote Controller .................................................................. 5

Display .................................................................................... 6

Install

1. Connect the Speakers ........................................................ 7

2. Connect the TV ................................................................... 8

3. Connect the HDMI AV Components ................................... 9

4. Connect the Audio Components ....................................... 10

5. Connect Other Cables .......................................................11

Initial Setup

Initial Setup with Auto Start-up Wizard ................................. 12

Playback

AV Component Playback ...................................................... 15

Internet Radio ....................................................................... 16

Spotify ................................................................................... 18

Music Server ......................................................................... 19

USB Storage Device ............................................................. 21

AirPlay

®

................................................................................ 23

BLUETOOTH

®

Playback ......................................................24

Listening to the FM Radio ..................................................... 25

Listening Modes ................................................................... 26

AV Adjust .............................................................................. 28

Supplementary Information

Supplementary information for player functions .................... 30

Advanced Setup

System Setup ........................................................................ 31

MCACC ................................................................................. 40

Network/Bluetooth ................................................................. 42

Firmware Update .................................................................. 45

Others

Troubleshooting .................................................................... 48

General Specifications .......................................................... 53

About HDMI .......................................................................... 55

License and Trademark Information ..................................... 56

> Before Start > Part Names > Install > Initial Setup > Playback

Supplementary Information | Advanced Setup | Others

NETWORK STEREO RECEIVER

SX-S30

Instruction

Manual

2

> Before Start > Part Names > Install > Initial Setup > Playback

Supplementary Information | Advanced Setup | Others

E

N

Before Start

What's in the box

0

Connect speakers with

4

Ω to

8

Ω impedance.

0 The power cord must be connected only after all other cable connections are completed.

0 We will not accept responsibility for damage arising from the connection of equipment

manufactured by other companies.

0 Functionality may be introduced by firmware updates and service providers may cease

services, meaning that some network services and content may become unavailable in

the future. Furthermore, available services may vary depending on your area of

residence.

0 Specifications and appearance are subject to change without prior notice.

Main unit (1)

Remote controller (RC-933R) (1), batteries (AAA/R03) (2)

Speaker setup microphone (1)

Indoor FM antenna (1)

> Before Start >Part Names > Install > Initial Setup > Playback

Supplementary Information | Advanced Setup | Others

3

E

N

Part Names

Front Panel

1. Í STANDBY/ON button: Turns the unit on or into standby mode.

2. DIRECT button: This switches the unit to the "Direct" mode (ÄP26) which shuts down

processing that affects sound quality, so sound closer to the original is reproduced. Press

again to cancel.

DIRECT indicator: This lights when the listening mode is "Direct" or "Pure Direct". The

display section and other indicators are turned off at this time.

3. Display (ÄP6)

4. Remote control sensor

5. NETWORK indicator: When the power of the unit is on, this lights when "NET" is selected

with the input selector and the unit is connected to the network. If the unit is in standby

mode, this lights when functions such as HDMI CEC and Network Standby are enabled.

6. INPUT SELECTOR dial: Switches the input to be played. (BD/DVD / CBL/SAT / GAME /

STRM BOX / CD / TV / PHONO / FM / NET / USB / BT AUDIO)

7. MASTER VOLUME dial: Allows you to adjust the volume.

8. PHONES jack: Stereo headphones with a mini plug (

Ø 3.5 mm) are connected.

9. BASS dial: Adjusts the bass.

10.

TREBLE dial: Adjusts the treble.

11.

FL OFF indicator: This lights when you have pressed DIMMER repeatedly to turn the

display off.

12.

USB port: A USB storage device is connected so that music files stored in it can be

played. You can also supply power (maximum 5 V/1 A) to USB devices with a USB cable.

 

  







4

> Before Start >Part Names > Install > Initial Setup > Playback

Supplementary Information | Advanced Setup | Others

E

N

Rear Panel

1. ANTENNA FM UNBAL 75 jack: Connect the supplied antenna.

2. Wireless antenna: Raise for Wi-Fi connection or when using a BLUETOOTH enabled

device. The diagram shows the movable range for the wireless antenna. Do not try to

force it beyond this range otherwise you may break it.

3. AUDIO IN jacks: Input AV component audio signals with an analog audio cable.

4. SIGNAL GND terminal: The ground wire of the turntable is connected.

5. DIGITAL IN OPTICAL/COAXIAL jacks: Input TV or AV component digital audio signals

with a digital optical cable or digital coaxial cable.

6. SETUP MIC jack: The supplied speaker setup microphone is connected.

7. Power cord

8. NETWORK port: Connect to the network with an Ethernet cable.

9. HDMI OUT jack: Connect a HDMI cable to transfer video signals and audio signals to a

TV.

10.

HDMI IN jacks: Input video signals and audio signals with a HDMI cable connected to an

AV component.

11.

SPEAKERS terminals: Connect speakers with speaker cables. When using banana

plugs, first tighten the speaker terminals and then insert the banana plugs.

12.

SUBWOOFER PRE OUT jack: Connect a powered subwoofer with a subwoofer cable.

180°

90°



 







  







> Before Start >Part Names > Install > Initial Setup > Playback

Supplementary Information | Advanced Setup | Others

5

E

N

Remote Controller

1. Í button: Turns the unit on or into standby mode.

2. Input selector buttons: Switches the input to be played.

3. (AV ADJUST) button: You can perform common settings on the TV screen. (ÄP28)

4. Cursors, ENTER button: Select the item with the cursors and press ENTER to confirm.

5. button: Displays the Home.

6. Volume buttons: Allows you to adjust the volume. This button also cancels the muting.

7. button: Temporarily mutes audio. Press again to cancel muting.

8. Listening mode buttons: Allows you to select the listening mode. (ÄP26)

9. Play buttons: You can start play of the Music Server or USB.

10.

button: You can start repeat or random play of the Music Server or USB.

CLEAR button: Deletes all characters you have entered when entering text on the TV

screen.

11.

(STATUS) button: Switches the information on the display.

12.

button: Returns the display to the previous state during setting.

13.

DIMMER button: You can switch the display off or adjust the brightness of the display in

three steps.

14.

MODE button: Switches tuning to an FM station between automatic tuning and manual

tuning.

15.

+Fav button: Used to register FM radio stations.































30°

Approx.5 m

(16 ft.)

6

> Before Start >Part Names > Install > Initial Setup > Playback

Supplementary Information | Advanced Setup | Others

E

N

Display

1. Lights in the following conditions.

HDMI: HDMI signals are input and selected.

ARC: Audio signals from the ARC compatible TV are input and selected.

USB: When "USB" is selected with the input selector and the unit is connected by USB

and the USB device is selected. Flashes if the USB is not properly connected.

NET: When "NET" is selected with the input selector and the unit is connected to the

network. It will flash if the connection to the network is not correct.

DIGITAL: Digital signals are input and the digital input selector is selected.

2. Lights when operating the "NET" or "USB" input selector indicating remote controller

cursor operations are possible in screens showing list of tracks, for example.

3. Lights when headphones are connected.

4. Lights when operating the "NET" or "USB" input selector when tracks are played or

paused.

5. Lights according to the type of input digital audio signals and the listening mode.

6. Lights in the following conditions.

AUTO: When FM tuning mode is auto.

TUNED: Receiving FM radio.

FM STEREO: Receiving FM stereo.

SLEEP: Sleep timer has been set.

ASb: When Auto Standby function is enabled. (ÄP38)

7. Flashes when muting is on.

8. Displays various information of the input signals. Characters that cannot be displayed on

this unit are replaced with asterisks ( ).



Neo:6









 

7

> Before Start > Part Names >Install > Initial Setup > Playback

Supplementary Information | Advanced Setup | Others

E

N

Install

1. Connect the Speakers

a Speaker cable, b Subwoofer cable

3

2

1

1/2˝

(12 mm)

1

3 4

2

a

b

Refer to the illustration to connect the speaker system.

Twist the wires of the speaker cable tightly before inserting

into the SPEAKERS terminals. After inserting the cables,

tighten the terminals firmly by turning to the right. Make

correct connection between the unit’s jacks and speaker’s

jacks (+ to + and – to –) for each channel. If connection is

wrong, a bass sound may become poor due to reverse

phase.

To connect a powered subwoofer, use a subwoofer cable

and connect to the SUBWOOFER PRE OUT jack.

Make sure the exposed wires of the speaker cable do not

stick out of the speaker terminals when connecting. If the

exposed wires of the speaker cable touch the rear panel or

the + and – wires touch each other, the protection circuit will

be activated. (ÄP48)

Setup

0 Settings for the speaker configuration you have connected

need to be made in "1. Full Auto MCACC" (ÄP13) in Initial

Setup.

8

> Before Start > Part Names >Install > Initial Setup > Playback

Supplementary Information | Advanced Setup | Others

E

N

2. Connect the TV

a HDMI cable, b Digital optical cable

a

b

DIGITAL

OPTICAL OUT

1

To ARC TV

For a TV that supports the ARC (Audio Return Channel)

(ÄP55) feature, use an HDMI cable and connect according

to illustration "a". Choose an HDMI IN jack on the TV that

supports ARC when connecting.

To Non-ARC TV

For a TV that does not support the ARC (Audio Return

Channel) feature, connect both the HDMI cable in illustration

"a" and the digital optical cable in "b".

Setup

0 Settings are required to use the ARC function. Select

"Yes" in "4. Audio Return Channel" (ÄP14) in the Initial

Setup.

0 Please refer to the TV’s operation manual for directions on

connections and setup for the TV.

9

> Before Start > Part Names >Install > Initial Setup > Playback

Supplementary Information | Advanced Setup | Others

E

N

3. Connect the HDMI AV Components

a HDMI cable

e.g. BD

a

HDMI OUT

1

a

BD/DVD GAME

Cable/Satellite

set-top box

Streaming media

player

This is an example of connection with an AV component

that has an HDMI jack. With connection to an AV

component that conforms with the CEC (Consumer

Electronics Control) standard, you can use features such as

the HDMI CEC feature that links with the input selector, and

the HDMI Standby Through feature which allows you to

play video and audio from AV components on the TV even

when this unit is in standby mode. (ÄP55)

0 To play 4K or 1080p video, use the high speed HDMI

cable.

Setup

0 Settings are required to use the HDMI CEC and HDMI

Standby Through features. (ÄP36, 37) Make settings after

all connections are complete.

0 To enjoy digital surround sound including Dolby Digital,

audio output should be set to "Bitstream output" on the

connected Blu-ray Disc player or other device.

10

> Before Start > Part Names >Install > Initial Setup > Playback

Supplementary Information | Advanced Setup | Others

E

N

4. Connect the Audio Components

a Digital coaxial cable, b Analog audio cable

CD

a

b

Turntable

Connecting a CD player

Use a digital coaxial cable to connect a CD player to the

DIGITAL IN COAXIAL jack.

Connecting a turntable

You can also connect a turntable that has an MM-type

cartridge to the PHONO jack.

0 If the turntable has a built-in audio equalizer, connect it to

an AUDIO IN jack other than the PHONO jack. Further, if

the turntable uses an MC type cartridge, install an audio

equalizer compatible with the MC type cartridge between

the unit and the turntable, then connect to any AUDIO IN

jack other than the PHONO jack.

If the turntable has a ground wire, connect it to the SIGNAL

GND terminal of this unit.

11

> Before Start > Part Names >Install > Initial Setup > Playback

Supplementary Information | Advanced Setup | Others

E

N

5. Connect Other Cables

a Indoor FM antenna, b Ethernet cable, c Power cord

b

c

1

3

2

a

Antenna Hookup

Connect the supplied FM antenna to the ANTENNA FM

UNBAL 75 terminal. Move the FM indoor antenna around

while playing the radio to find the position with the best

reception.

Network Hookup

Connect this unit to the network using wired LAN or Wi-Fi

(wireless LAN). You can enjoy network features such as

internet radio by connecting the unit to the network. If you

connect by wired LAN, connect with an Ethernet cable to the

NETWORK port as shown in the illustration. To connect by

Wi-Fi, then after selecting "Wireless" in "3. Network

Connection" (ÄP13) in Initial Setup, select the desired

setting method and follow the onscreen instructions to

configure the connection.

Power Cord Hookup

Connect the power cord of this unit only after all other

connections are completed.

12

> Before Start > Part Names > Install > Initial Setup >Playback

Supplementary Information | Advanced Setup | Others

E

N

Initial Setup

Initial Setup with Auto Start-up Wizard

1

3 4

2

TV's remote controller

Initial Setup starts automatically

1. Switch the input on the TV to that assigned to the unit.

2. Put batteries into the remote controller of this unit.

3. Press Í on the remote controller. When power turns on

for the first time, an Initial Setup screen is automatically

displayed on the TV to allow you to make settings

required for start up.

4. Follow the on-screen instructions to select the item with

the cursors of the remote controller and press ENTER to

confirm your selection.

0 To return to the previous screen, press .

To redo Initial Setup: If you terminate the procedure on the

way or want to change a setting made during Initial Setup,

press on the remote controller, select "Miscellaneous" -

"Initial Setup" in the System Setup menu from Home and

press ENTER. To select the language displayed again,

change "OSD Language". (ÄP31)

Initial Setup

Language Select

English

Deutsch

Français

Español

Italiano

Nederlands

Svenska

13

> Before Start > Part Names > Install > Initial Setup >Playback

Supplementary Information | Advanced Setup | Others

E

N

1. Full Auto MCACC

Place the supplied speaker setup microphone in the

listening position, measure the test tones emitted by the

speakers, then the unit automatically sets the optimum

volume level for each speaker, the crossover frequencies,

and the distance from the listening position. This also

automatically adjusts the equalizers for the speakers and

enables correction of distortion caused by the acoustic

environment of the room.

0 Calibration takes between 3 to 12 minutes to be

completed. The speakers emit the test tone at high

volume during measurement, so be careful of your

surroundings. Keep the room as quiet as possible during

measurement.

0 If the power of this unit suddenly turns off, the wires in the

speaker cables may have touch the rear panel or other

wires and tripped the protection circuit. Twist the wires

again properly and make sure they do not stick out of the

speaker terminals when connecting.

1. Place the supplied speaker setup microphone in the

listening position, and connect to the SETUP MIC jack on

the main unit.

When putting the speaker setup microphone on a tripod,

refer to the illustration when putting it in place.

0 To cancel Full Auto MCACC partway through,

disconnect the speaker setup microphone.

2. Select whether a subwoofer is connected.

The image on the screen changes as you choose the

number of channels in "Speaker Channels", so refer to it

when performing the settings. Also use this screen to

select whether you have connected a subwoofer.

0 If you have connected a subwoofer, check the power

and volume of the subwoofer. The low frequencies

played by the subwoofer may not be discernible, so

set its volume to at least halfway.

3. Test tones are emitted by the speakers, and firstly the

unit detects the speakers connected and the noise in the

environment.

4. After the results of the above measurements are

displayed, select "Next", press ENTER on the remote

controller, and the test tones are emitted again, and the

unit automatically makes settings such as the optimum

volume level and the crossover frequency.

5. When the measurement is completed, the measurement

result is displayed.

Press the cursors w/x on the remote controller to check

the settings. Press ENTER when "Save" is selected to

save the settings.

6. Disconnect the speaker setup microphone.You cannot

use any other menu options while it is connected.

2. Source Connection

Check that each input source is connected correctly. Follow

the guidance, select the input you want to confirm, start play

of the selected player, and confirm that the images appear

on the TV and that sound is played.

3. Network Connection

Set up Wi-Fi connection with an access point such as a

wireless LAN router. There are the following two methods of

connecting by Wi-Fi:

"Scan Networks": Search for an access point from this

unit. Find out the SSID of the access point beforehand.

"Use iOS Device (iOS7 or later)": Share the iOS device's

Wi-Fi settings with this unit.

If you select "Scan Networks", there are a further two

choices of connection method. Check the following.

0 "Enter Password": Enter the password (or key) of the

access point to connect.

0 "Push Button": If the access point has an automatic

connection button, you can connect without entering a

password.

0 If the SSID of the access point is not displayed, then in

the screen listing the SSIDs, select "Other..." with the x

SETUP MIC

Specifies whether the subwoofer is connected or not.

14

> Before Start > Part Names > Install > Initial Setup >Playback

Supplementary Information | Advanced Setup | Others

E

N

button on the remote controller and press ENTER, then

follow the on-screen instructions.

Keyboard input: To switch between upper and lower case,

select "A/a" on the screen and press ENTER. To select

whether to mask the password with " " or display it in plain

text, press +Fav on the remote controller. Pressing CLEAR

will delete all the input characters.

Privacy policy: A confirmation screen asking you to agree

to the privacy policy is displayed during network setting.

Select "Yes" and press ENTER to indicate agreement.

4. Audio Return Channel

If you have connected a TV that supports ARC, select

"Yes". This unit's ARC setting turns on and you can listen to

the TV's audio through this unit.

0 If you select "Yes", the HDMI CEC function is enabled

and power consumption increases during standby.

Wi-Fi Setup

Ðáóó÷ïòä

When finished, select the "OK" key.

A/aAll Erase

OKA/a

a b cdefghi jklm

nopqr s t uvwx y z

1 2 34567890- ^\

, . /;:@[]

Hide/Show

15

> Before Start > Part Names > Install > Initial Setup >Playback

Supplementary Information | Advanced Setup | Others

E

N

Playback

AV Component Playback

Basic operations

Play an AV component or TV connected to this unit with an

HDMI cable or other cable.

1. Switch the input on the TV to that assigned to the unit.

2. Press the input selector (a) on the remote controller with

the same name as the jack to which you connected the

player to switch the input.

For example, press BD/DVD to play the player connected

to the BD/DVD jack. Press TV to listen the TV's sound.

0 Note that when the CEC link function works, the input

switches automatically when you have connected a

CEC compliant TV and player to this unit using HDMI

connection.

3. Start play on the player.

4. Use VOL+/– (b) to adjust the volume.

a

b

16

> Before Start > Part Names > Install > Initial Setup >Playback

Supplementary Information | Advanced Setup | Others

E

N

Internet Radio

Basic operations

When this unit is connected to a network, you can listen to

TuneIn or other preregistered Internet radio services.

Depending on the internet radio service, the user may need

to register from their computer first.

1. Switch the input on the TV to that assigned to the unit.

2. Press NET on the remote controller.

3. Follow the on-screen instructions, using the cursors to

select radio stations and programs, then press ENTER

(b) to play. Play starts when 100% is displayed for

buffering.

0 To return to the previous screen, press (c).

0 If you cannot select a network service, it will become

selectable when the network function is started.

Regarding TuneIn Radio

To display the TuneIn Radio menu during play, press

ENTER (b) on the remote controller.

Add to My Presets Registers radio stations being

broadcast and programs in "My Presets". Once registered,

"My Presets" is displayed in the level under TuneIn Radio.

To play, select the program you like from "My Presets".

Remove from My Presets Removes a radio station or

program from "My Presets" in TuneIn Radio.

Pandora

®

(U.S. only)

Pandora is a free, personalized Internet radio service that

plays the music you know and helps you discover music

you’ll love. After selecting "Pandora", do the following.

1. Use y/z (a) on the remote controller to select "I have a

Pandora Account" or "I’m new to Pandora" and then

press ENTER (b).

If you are new to Pandora, select "I’m new to Pandora".

You will see an activation code on your TV screen.

Please write down this code. Go to an Internet connected

computer and point your browser to www.pandora.com/

pioneer. Enter your activation code and then follow the

instructions to create your Pandora account and your

personalized Pandora stations. You can create your

stations by entering your favorite tracks and artists when

prompted. After you have created your account and

stations you can return to your receiver and press

ENTER (b) to begin listening to your personalized

Pandora.

If you have an existing Pandora account, you can add

your Pandora account to your receiver by selecting "I

have a Pandora Account" and logging in with your email

and password.

2. To play a station, use y/z (a) on the remote controller to

select the station from your station list, and then press

ENTER (b). Playback starts and the playback screen

appears.

Create new station: Enter the name of a track, artist, or

genre and Pandora will create a unique radio station for you

based on the musical qualities of that track, artist, or genre.

Regarding the Pandora Menu: Icons are displayed on the

screen while playing a station. You can do the following by

selecting the icon with y/z (a) on the remote controller and

pressing ENTER (b).

a

c

b

1

> Before Start > Part Names > Install > Initial Setup >Playback

Supplementary Information | Advanced Setup | Others

17

E

N

(I like this track) :

Give a track “thumbs-up” and Pandora will play more music

like it.

(I don't like this track) :

Give a track “thumbs-down” and Pandora will ban that track

from the current station.

:

Automatically find stations matching your preferences

based on genre, specific artists, and songs, and delete

those stations you don't need.

18

> Before Start > Part Names > Install > Initial Setup >Playback

Supplementary Information | Advanced Setup | Others

E

N

Spotify

b

d

e

c

a

1

2

3

4

Basic operations

Spotify Connect play is possible by connecting this unit to

the same network as a smart phone or tablet. To enable

Spotify Connect, install the Spotify application on your

smartphone or tablet and create a Spotify premium account.

1. Connect the smartphone to the network that this unit is

connected to.

2. Click the Connect icon in the track play screen of the

Spotify app.

3. Select this unit.

4. This unit turns on automatically and the input selector

changes to NET and streaming of Spotify starts.

0 If "Hardware" - "Power Management" - "Network

Standby" is set to "Off" in the System Setup menu from

Home, manually turn the unit on and then press NET on

the remote controller.

0 Refer to the following for Spotify settings:

www.spotify.com/connect/

0 The Spotify software is subject to third party licenses

found here:

www.spotify.com/connect/third-party-licenses

The following remote controller operations are also

possible.

(a) Pressed during play, this button changes the displayed

track information.

(b) This button plays the previous track.

(c) This button lets you start repeat or random playback.

Pressing this button repeatedly cycles through the

repeat modes.

(d) Pressed during play this button pauses playback.

Pressed while paused, and it restarts play.

(e) This button plays the next track.

19

> Before Start > Part Names > Install > Initial Setup >Playback

Supplementary Information | Advanced Setup | Others

E

N

Music Server

It is possible to stream music files stored on PCs or NAS

devices connected to the same network as this unit. The

network servers this unit is compatible with are those PCs

with players installed that have the server functionality of

Windows Media

®

Player 11 or 12, or NAS that are

compatible with home network functionality. You may need

to make some settings in advance to use Windows Media

®

Player 11 or 12. Note that only music files registered in the

library of Windows Media

®

Player can be played.

Configuring Windows Media

®

Player

∫ Windows Media

®

Player 11

1. Turn on your PC and start Windows Media

®

Player 11.

2. In the "Library" menu, select "Media Sharing" to display a

dialog box.

3. Select the "Share my media" check box, and then click

"OK" to display the compatible devices.

4. Select this unit, click "Allow" and put a check mark next to

the icon for this unit.

5. Click "OK" to close the dialog.

0 Depending of the version of Windows Media

®

Player,

there may be differences in the names of items you can

select.

∫ Windows Media

®

Player 12

1. Turn on your PC and start Windows Media

®

Player 12.

2. In the "Stream" menu, select "Turn on media streaming"

to display a dialog box.

0 If media streaming is already turned on, select "More

streaming options..." in the "Stream" menu to list players

in the network, and then go to step 4.

3. Click "Turn on media streaming" to list players in the

network.

4. Select this unit in "Media streaming options" and check

that it is set to "Allow".

5. Click "OK" to close the dialog.

0 Depending of the version of Windows Media

®

Player,

there may be differences in the names of items you can

select.

Playing

1. Start the server (Windows Media

®

Player 11, Windows

Media

®

Player 12, or NAS device) containing the music

files to play.

2. Make sure that the PCs and/or NASs are properly

connected to the same network as this unit.

3. Switch the input on the TV to that assigned to the unit.

4. Press NET on the remote controller.

5. With the cursors on the remote controller, select "Music

Server", and then press ENTER (b).

6. Select the target server with the cursors on the remote

controller and press ENTER (b) to display the items list

screen.

7. With the cursors on the remote controller, select the

music file to play, and then press ENTER (b) to start

playback. To return to the previous screen, press (d).

0 If "No Item." is displayed, check whether the network is

properly connected.

0 Depending on the server and share settings, the unit may

not recognize it, or may not be able to play its music files.

Furthermore, the unit cannot access pictures and videos

stored on servers.

a

c

d

b

e

f

g

h

1

La page charge ...

Pioneer SX-S30 Manuel utilisateur

Pioneer SX-S30 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents